hcd-gnz5d - especarchive.espec.ws/files/sony hcd-gnz5d.pdf1 ver. 1.1 2005. 12 model name using...
TRANSCRIPT
1
Ver. 1.1 2005. 12
Model Name Using Similar Mechanism HCD-GNZ7D/GNZ8D/GNZ9DDVD
DVD Mechanism Type CDM74HF-DVBU101//CSection
Optical Pick-up Name KHM-310CAB/C2NP
Tape Deck Model Name Using Similar Machanism HCD-GNZ7D/GNZ8D/GNZ9D
Section Tape Transport Mechanism Type CWM43FR601
SERVICE MANUAL E Model
HCD-GNZ5D
Amplifier sectionThe following measured at AC 120, 220, 230 – 240 V,50/60 HzContinuous RMS power output (reference)
50 + 50 watts(6 ohms at 1 kHz, 10%THD)
InputsMIC (phone jack): sensitivity 1 mV,
impedance 10 kilohmsOutputsVIDEO OUT (phono jack):
max. output level1 Vp-p, unbalanced, Syncnegative, load impedance75 ohms
DIGITAL OPTICAL OUT (Square optical connector jack,rear panel)Wavelength 660 nmPHONES (stereo mini jack):
accepts headphones of8 ohms or more
FRONT SPEAKER: Use only the suppliedspeaker SS-GNZ5D
SPECIFICATIONS
Disc player sectionSystem Compact disc and digital
audio and video systemLaser Semiconductor laser
(DVD: λ=650 nm,CD: λ=790 nm)Emission duration:continuous
Frequency response DVD (PCM 48 kHz):2 Hz – 22 kHz (±1 dB)CD: 2 Hz – 20 kHz (±1 dB)
Video color system formatNTSC, PAL
Tape deck sectionRecording system 4-track 2-channel stereoFrequency response 40 – 13,000 Hz (±3 dB),
using Sony TYPE Icassette
Sony CorporationHome Audio Division
Published by Sony Engineering Corporation
9-879-821-022005L04-1
© 2005. 12
– Continued on next page –
DVD DECK RECEIVER
• HCD-GNZ5D is the tuner, deck,DVD and amplifier section inMHC-GNZ5D.
2
HCD-GNZ5D
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINEWITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND INTHE PARTS LIST ARE CRITICAL TO SAFE OPERATION.REPLACE THESE COMPONENTS WITH SONY PARTS WHOSEPART NUMBERS APPEAR AS SHOWN IN THIS MANUAL ORIN SUPPLEMENTS PUBLISHED BY SONY.
Tuner sectionFM stereo, FM/AM superheterodyne tuner
FM tuner sectionTuning range 87.5 – 108.0 MHz
(50-kHz step)Antenna FM lead antennaAntenna terminals 75 ohm unbalancedIntermediate frequency 10.7 MHz
AM tuner sectionTuning range 530 – 1,710 kHz (with the
interval set at 10 kHz)531 – 1,602 kHz (with theinterval set at 9 kHz)
Antenna AM loop antennaAntenna terminals External antenna terminalIntermediate frequency 450 kHz
GeneralPower requirementsIndian model: 220 – 240 V AC, 50/60 HzThai model: 220 V AC, 50/60 HzOther models: 120 V, 220 V or 230 –
240 V AC, 50/60 HzAdjustable with voltageselector
Power consumption 110 watts
Dimensions (w/h/d) (excl. speakers)Approx. 280 × 326 × 365 mm
Mass (excl. speakers) Approx. 9 kg
Design and specifications are subject to change withoutnotice.
3
CAUTIONUse of controls or adjustments or performance of proceduresother than those specified herein may result in hazardousradiation exposure.
HCD-GNZ5D
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCKOR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostaticbreakdown because of the potential difference generated by thecharged electrostatic load, etc. on clothing and the human body.During repair, pay attention to electrostatic break-down and alsouse the procedure in the printed matter which is included in therepair parts.The flexible board is easily damaged and should be handled withcare.
Notes on Chip Component Replacement• Never reuse a disconnected chip component.• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing• Keep the temperature of soldering iron around 270°C during re-
pairing.• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).• Be careful not to apply force on the conductor when soldering
or unsoldering.
UNLEADED SOLDERBoards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARKUnleaded solder has the following characteristics.• Unleaded solder melts at a temperature about 40 °C higher than
ordinary solder.Ordinary soldering irons can be used but the iron tip has to beapplied to the solder joint for a slightly longer time.Soldering irons using a temperature regulator should be set to about350 °C.Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow) thanordinary solder so use caution not to let solder bridges occur suchas on IC pins, etc.
• Usable with ordinary solderIt is best to use only unleaded solder but unleaded solder may alsobe added to ordinary solder.
This appliance isclaassified as a CLASS 1LASER product. Thislabel is located on therear exterior.
NOTES ON LASER DIODE EMISSION CHECKThe laser beam on this model is concentrated so as to be focused onthe disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission,observe from more than 30 cm away from the objective lens.
Laser component in this product is capableof emitting radiation exceeding the limit forClass 1.
Ver. 1.1
Note on DMB11 board replacementNew part of EEP ROM (IC103) on the DMB11 board cannot beused. Therefore, if the mounted DMB11 board (A-1109-317-A, etc.)is replaced, exchange new EEP ROM (IC103) with that used beforethe replacement.
4
HCD-GNZ5D
MODEL IDENTIFICATION
– BACK PANEL –
MODEL PARTS No.
GNZ5D: PH 2-582-753-0s
GNZ5D: E3, E15 2-582-753-1s
GNZ5D: E12, E13 2-582-753-2s
PARTS No.
• AbbreviationE3 : 240 V AC area in E modelE12 : 220 – 240 V AC area in E modelE13 : 220 – 230 V AC area in E modelE15 : Iran modelPH : Philippine model
5
TABLE OF CONTENTS
HCD-GNZ5D
7. DIAGRAMS7-1. Circuit Boards Location .................................................... 267-2. Block Diagram — RF/Servo Section — ........................... 277-3. Block Diagram — Video Section — ................................. 287-4. Block Diagram — Main Section — .................................. 297-5. Block Diagram — Function/Power Section — ................. 307-6. Printed Wiring Boards — Driver Section —..................... 327-7. Schematic Diagram — Driver Section — ......................... 337-8. Printed Wiring Board — DMB11 Section — ................... 347-9. Schematic Diagram — DMB11 Section (1/4) — ............. 367-10. Schematic Diagram — DMB11 Section (2/4) — ............. 377-11. Schematic Diagram — DMB11 Section (3/4) — ............. 387-12. Schematic Diagram — DMB11 Section (4/4) — ............. 397-13. Printed Wiring Boards — Audio Section — ..................... 407-14. Schematic Diagram — Audio Section (1/3) —................. 417-15. Schematic Diagram — Audio Section (2/3) —................. 427-16. Schematic Diagram — Audio Section (3/3) —................. 437-17. Printed Wiring Board — Video Section — ....................... 447-18. Schematic Diagram — Video Section — .......................... 457-19. Printed Wiring Board — Front AMP Section — .............. 467-20. Schematic Diagram — Front AMP Section — ................. 477-21. Schematic Diagram — Panel Section (1/2) — ................. 487-22. Schematic Diagram — Panel Section (2/2) — ................. 497-23. Printed Wiring Boards — Panel Section — ...................... 507-24. Printed Wiring Board — Jack Section — ......................... 517-25. Schematic Diagram — Jack Section — ............................ 527-26. Schematic Diagram — Power Section — ......................... 537-27. Printed Wiring Board — Trans Section — ....................... 547-28. Printed Wiring Board — Sub Trans Section — ................ 55
8. EXPLODED VIEWS8-1. Main Section ..................................................................... 648-2. Front Panel Section (1) ...................................................... 658-3. Front Panel Section (2) ...................................................... 668-4. Front Panel Section (3) ...................................................... 678-5. DVD Block Section ........................................................... 688-6. Chassis Section ................................................................. 698-7. Audio Board Section ......................................................... 708-8. DVD Mechanism Deck Section (1) .................................. 718-9. DVD Mechanism Deck Section (2) .................................. 72
9. ELECTRICAL PARTS LIST ........................................ 73
1. SERVICE NOTE1-1. Service Position of CDM .................................................... 61-2. Service Position of DMB11 Board, Video Board ............... 61-3. Service Position of TCM ..................................................... 71-4. Service Position of Front AMP Board ................................ 7
2. GENERALMain Unit ................................................................................ 8Remote Control ....................................................................... 9
3. DISASSEMBLY3-1. Case ................................................................................... 113-2. Loading Panel Assy ........................................................... 113-3. Front Panel Section ........................................................... 123-4. DVD Block Section ........................................................... 123-5. Tape Mechanism Deck Section ......................................... 133-6. Panel Board ....................................................................... 133-7. Jack Board ......................................................................... 143-8. Back Panel Section ............................................................ 143-9. Boards Section .................................................................. 153-10. Audio Board ...................................................................... 153-11. DVD Mechanism Block, Video Board, DMB11 Board .... 163-12. Pick-up Unit ...................................................................... 163-13. SW Board, Driver Board ................................................... 173-14. Sensor Board ..................................................................... 173-15. Motor (TB) Board ............................................................. 183-16. Motor (LD) Board ............................................................. 18
4. TEST MODE4-1. General Description .......................................................... 204-2. Starting Test Mode ............................................................ 204-3. Drive Manual Operation .................................................... 204-4. Mirror Time Adjustment ................................................... 204-5. Executing IOP Measurement ............................................ 22
5. MECHANICAL ADJUSTMENTS ............................... 23
6. ELECTRICAL ADJUSTMENTS ................................. 24
6
HCD-GNZ5D
1-2. SERVICE POSITION OF DMB11 BOARD, VIDEO BOARD
1-1. SERVICE POSITION OF CDM
SECTION 1SERVICE NOTE
stand
DVD mechanism block
PANEL board
DMB11 board
VIDEO boardJ-2501-102-A
7
HCD-GNZ5D
1-4. SERVICE POSITION OF FRONT AMP BOARD
1-3. SERVICE POSITION OF TCM
earth is taken
FRONT AMP board
insulating plate
AUDIO board
earth is taken
8
HCD-GNZ5DSECTION 2GENERAL This section is extracted
from instruction manual.
Ad
ditio
nal In
form
ation
67GB
Main unit
CD SYNC wg (38)Deck A ws (37, 39)Deck B qg (37, 38, 39, 46)DIRECTION qd (37, 38, 39)DISC 1 – 3 qs (12, 14, 38, 56)DISC SKIP/EX-CHANGE qa (9,
11, 12, 14, 38)Disc tray 9 (11)DISPLAY 2 (47, 48, 56)Display window 6DVD wk (9, 38)EQ BAND/MEMORY 4 (41)GROOVE wh (40)MIC jack ql (41)MIC LEVEL qk (41)
Operation Dial (l L) 5 (41)
PHONES jack w; PRESET EQ wj (40, 41)REC PAUSE/START wf (38, 39)Remote sensor 3SOUND FIELD 7 (40)TAPE A/B wk (37, 38, 39)TUNER/BAND wk (35, 36, 39)TUNING + qh (35, 36) TUNING – wa (35, 36)VOLUME control qj (42)
?/1 (power) 1 (8, 36, 45, 56)nN (play) 8 (11, 29, 37, 38)X (pause) 8 (8, 11, 37)x (stop) 8 (9, 11, 30, 37, 38, 56)Z OPEN/CLOSE q; (11)Z PUSH (deck B) (eject) qf (37)M (fast forward) qh (12, 37)y (slow forward) qh (12)m (rewind) wa (12, 37)
(slow rewind) wa (12)Z PUSH (deck A) (eject) wd (37)
List of button locations and reference pages
How to use this pageUse this page to find the location of buttons and other parts of the system that are mentioned in the text.
Illustration numberr
TAPE A/B wk (37, 38, 39)R R
Name of button/part Reference page
ALPHABETICAL ORDER
A — N O — Z
BUTTON DESCRIPTIONS
M yM y
nN
X
x
qd
qs
qfqg
q;
qa
12 9876534
qh
qjqlqkw;wa
wkwjwh
wd
wfwg
ws
continued
9
HCD-GNZ5D
Remote control
ALBUM +/– wf (11, 50)ANGLE 5 (34)AUDIO 4 (25, 41)CLEAR es (10, 14, 15, 16, 20,
23)DISC SKIP w; (12, 14)DISPLAY qj (47, 48)ENTER qs (9, 13, 14, 16, 17, 19,
21, 23, 27, 35, 43, 45, 46, 56)FM MODE ws (36)FUNCTION +/– 2 (10, 11, 35,
36)KARAOKE MODE qg (41)KARAOKE PON qh (42)MENU 6 (16, 18, 19, 21, 35)Number buttons* qf (17, 31)PICTURE NAVI 3 (20, 24)PRESET + wh (36)PRESET – e; (36)
REPEAT ws (15)SLEEP qk (45)SOUND FIELD wa (40)SUBTITLE wd (34)THEATRE SYNC ql (50)TIMER MENU eg (9, 45, 46)TIME/TEXT ef (47, 48)TOP MENU qd (16)TUNING + 9 (35, 36)TUNING – qa (35, 36)TV wk (50)TV CH + wh (50)TV CH – e; (50)TV/VIDEO qk (50)TV VOL +/–* 7 (50)VOLUME +/–* 7 (45)
?/1 (power) 1 (8, 45, 56)TV ?/1 1 (50)
REPLAY/ADVANCE /c STEP/STEP C 8 (12)
SLOW y 9 (12)M (fast forward) 9 (12, 37)X (pause) q; (11, 37)
SLOW qa (12)m (rewind) qa (12, 37) M/m/</, qs (9, 13, 26, 43, 45)
DISPLAY wg (13, 26, 49)> (go forward) wh (11) x (stop) wj (37). (go back) e; (11) H (play)* wl (11, 29) O RETURN ea (17)-/-- esKEY CONTROL #/2 ed (42)
* The H, number 5 and VOLUME + (TV VOL +) buttons have tactile dots. Use the tactile dots as references when operatihng the system.
ALPHABETICAL ORDER
A — Q R — Z
BUTTON DESCRIPTIONS
bB
< z
V
v
+
–
+–
+ +
–
+
X
yy
x
m M
. >
O
bB
< z < z
V
v
+
–
+–
+
X x
m M
. >
O
#2
c C
< z
H yy H
c C
–2 #
1
2
3
4
5
6
7
8
9
q;
qa
qs
qd
qf
qgqh
qj
qkql
w;
waws
wd
wf
wgwh
wjwk
wl
e;
ea
es
ed
ef
eg
10
HCD-GNZ5DSECTION 3
DISASSEMBLY
Note : Disassemble the unit in the order as shown below.
3-15. MOTOR (TB) BOARD(Page 18)
3-16. MOTOR (LD) BOARD(Page 18)
3-1. CASE(Page 11)
3-2. LOADING PANEL ASSY(Page 11)
SET
3-3. FRONT PANEL SECTION(Page 12)
3-12. PICK-UP UNIT(Page 16)
3-14. SENSOR BOARD(Page 17)
3-13. SW BOARD,DRIVER BOARD(Page 17)
3-4. DVD BLOCK SECTION(Page 12)
3-8. BACK PANEL SECTION(Page 14)
3-9. BOARDS SECTION(Page 15)
3-10. AUDIO BOARD(Page 15)
3-11. DVD MECHANISM BLOCK,VIDEO BOARD,DMB11 BOARD(Page 16)
3-6. PANEL BOARD(Page 13)
3-5. TAPE MECHANISM DECK SECTION
(Page 13)
3-7. JACK BOARD(Page 14)
11
HCD-GNZ5D
3-2. LOADING PANEL ASSY
Note : Follow the disassembly procedure in the numerical order given.3-1. CASE
2 screw (case 3 TP2)
7 screw (case 3 TP2)
1 screw (case 3 TP2)
6 screw (case 3 TP2)
5 case (side-R)
0 case (side-R)
qg case (top)
3 screw (+BVTT 3 × 6)
qa two screws (+BVTT 3 × 6)
qs two screws (+BVTP 3 × 10)
8 screw (+BVTT 3 × 6)
4
9qd
qf
qd
3 Pull-out the disc tray.
5 loading panel assy
2 Turn the pulley to the direction of arrow.
1 The DVD mechanism block has a cover.So the pulley may not be rotated unless the cover is opened.
pulley
Front panel side
CD mechanism deck (CDM74HF)
cover (B-CDM)
4
12
HCD-GNZ5D
3-3. FRONT PANEL SECTION
qs CN601 (3P)
qa CN602 (8P)
0 CN751 (10P)
7 CN752 (27 core)
1 CN005 (13 core)
8 CN755 (4P)
9 CN203 (4P)
2 CN102 (13 core)
3 screw (+BVTP 3 × 10)
4 screw (+BVTP 3 × 10)
6
5 four screws (+BVTT 3 × 6)
qd front panel section
3-4. DVD BLOCK SECTION
1 screw (+BVTP 3 × 10)
2 three screws (+BVTT 3 × 6)
34 CN301 (17 core)
5 CN851 (8P)
6 DVD block section
13
HCD-GNZ5D
3-6. PANEL BOARD
3-5. TAPE MECHANISM DECK SECTION
4 two screws (+BVTP 2.6 (3CR))
5 two screws (+BVTP 2.6 (3CR))
2 screw (+BVTP 2.6 (3CR))
3 GUARD board
6 screw (+BVTP 2.6 (3CR))
7 tape mechanism deck
clamp
lug
lug
1 connector
5 CN151 (7P)
6 PANEL board
4 six claws
1 five screws (+BVTP 2.6 (3CR))
2 two screws (+BVTP 2.6 (3CR))
3 three screws (+BVTP 2.6 (3CR))
14
HCD-GNZ5D
3-7. JACK BOARD
4 bracket (TC-JACK)
5 JACK board
1 mic knob
2 two screws (+BVTP 2.6 (3CR))
3 two screws (+BVTT 3 × 6)
3-8. BACK PANEL SECTION
8 back panel section
5 three screws (+BVTT 3 × 6)
3 two screws (+BVTT 3 × 6)
4 screw (+BVTP 3 × 10)
7 CN754 (2P)
6
1 CN753 (9P)
2 CN306 (3P)
15
HCD-GNZ5D
3-10. AUDIO BOARD
3-9. BOARDS SECTION
6 boards section
4 two screws (+BV sumitite (B3))
5 two screws (+BV sumitite (B3))
3 two screws (+BVTT 3 × 6)
2 CN914 (10P)
1 CN915 (4P)
2 AUDIO board
CN201
CN202
1 claw
16
HCD-GNZ5D
3-12. PICK-UP UNIT
3-11. DVD MECHANISM BLOCK, VIDEO BOARD, DMB11 BOARD
qf screw (+BVTP 3 × 8)
qj bracket (DVD)qg screw (+BVTP 3 × 8)
qh
3 two screws (+BVTT 3 × 6)
6 three screws (+BVTT 3 × 6)
0 two screws (+BVTT 3 × 6)
qd two screws (+BVTP 3 × 8)
qa two screws (+BVTT 3 × 6)
5 VIDEO board
7 REINFORCE (CDM) board
qs DMB11 board
8 CN201 (6P)
9 CN101 (24 core)
qk DVD mechanism block
2 CN401 (5P)
1 CN801 (5P)
4 claw
2 two insulator screws
4 two insulators
5 two insulators
3 two insulator screws
6 pick-up unit
7 holder (310)1 floating screw (+PTPWH M2.6)
Note : Be short-circuited of the land of optical pick-up when CN101is done in pulling out.
17
HCD-GNZ5D
3-13. SW BOARD, DRIVER BOARD
6 DRIVER board2 SW board
3 CN704
4 CN703
7 CN702 (flat type)
5 two screws (+BTTP (M2.6))
1 screw (+BTTP (M2.6))
3-14. SENSOR BOARD
2 tray
3 belt (table)
5 pulley (table)
8 screw (+BTTP (M2.6))
9 SENSOR board
7 gear (geneva)
0 CN731
1 floating screw (+PTPWH M2.6)
6 floating screw (+PTPWH M2.6)
4 floating screw (+PTPWH M2.6)
18
HCD-GNZ5D
3-15. MOTOR (TB) BOARD
3-16. MOTOR (LD) BOARD
5 Remove the two solders of motor.
4 MOTOR (TB) board
2 stopper
2 stopper
6 table motor assy (M741)
table assy
3 two screws (+BTTP (M2.6))
1
4 Remove the two solders of motor.3 MOTOR (LD) board
1 belt (loading)
5 loading motor assy (M751)
2 two screws (+BTTP (M2.6))
19
HCD-GNZ5DSECTION 4TEST MODE
[Cold Reset]• The cold reset clears all data including preset data stored in the
RAM to initial conditions. Execute this mode when returningthe set to the customer.
Procedure:1. Press three buttons of x , [DISPLAY] and [DISC 1]
simultaneously.2. The message “COLD RESET” is displayed, and the set is reset.
[Tuner Step Change]• A step of AM channels can be changed over between 9 kHz and
10 kHz.Procedure:1. Press the /1 button to turn the power ON, and set the function
to TUNER/BAND “AM”.2. Press the `/1 button to turn the power OFF.3. Press two buttons of [TUNING +] and `/1 simultaneously, and
the message changes to “AM 9 k STEP” or “AM 10 k STEP”,and thus the channel step is changed over.
[Color System Change]Procedure:1. Press the `/1 button to turn the power ON.2. Press two buttons of X and `/1 simultaneously.3. The message “COLOR NTSC” or “COLOR PAL” is displayed.
[Disc Tray Lock]The disc tray lock function for the antitheft of a demonstration discin the store is equipped.Setting Procedure :1. Press the ?/1 button to turn the power ON.2. Press two buttons of x and Z simultaneously for five seconds.3. The message “LOCKED” is displayed, and the tray is locked.Releasing Procedure :1. Press two buttons of x and Z simultaneously for five seconds.2. The message “UNLOCKED” is displayed, and the tray is
unlocked.Note: When the message “LOCKED” is displayed, the tray lock is
not released by turning power ON/OFF with the ?/1 button.
[Panel Test Mode]• This mode is used to check the fluorescent indicator tube, LEDs,
keyboard, volume and phones.Enter The Panel Test ModeProcedure:1. Press three buttons of x , [DISPLAY] and [DISC 2] simulta-
neously.2. LEDs and fluorescent indicator tube are all turned on.Model InformationProcedure:1. It puts it into the start of the panel test mode.2. Press the [DIRECTION] button, the mode change model name
or destination display.Key Test ModeProcedure:1. It puts it into the start of the panel test mode.2. Press the Y button, the mode change key test mode.
VACS DisplayProcedure:1. It puts it into the start of the panel test mode.2. Press the X button, the mode change VACS display.
The message “VACS 0+0” is displayed.Version DisplayProcedure:1. It puts it into the start of the panel test mode.2. Press the [DIRECTION] button, the mode change version display.
Press the [DISPLAY] button, the mode change version or days isdisplayed.
3. You can exit the Test Mode when you press three buttons of X ,[DISPLAY] and [DISC 2] simultaneously.
[Common Test Mode]• This mode is used to check operations of the respective sections
of Amplifier and Tape.Procedure:• To enter MC Test Mode1. Press the `/1 button to turn the power ON.2. Press three buttons of x , [DISPLAY] and [DISC 3] simulta-
neously.
* Check of Amplifier
Initial settings: EQ , FLATVACS , ON
• When you press the [EQ BAND/MEMORY] button, the message“GEQ FLAT” is displayed, and the entire band of the graphicequalizer is set to the center level.
• Whenever you press the [GROOVE] button, it toggles between“VACS ON” and “VACS OFF” so that you can switch ON orOFF of VACS.
* To return to normal mode again.1. When you want to exit this mode, press the `/1 button.2. The cold reset is enforced at the same time.
[DVD and CD Ship Mode (No Memory Clear)]• This mode moves the position to the position durable to
vibration. Use this mode when returning the set to the customerafter repair.
Procedure:1. Press the `/1 button to turn the power ON.2. Press two buttons of x and [DISC SKIP] simultaneously.3. After the “STANDBY” display blinks 15 times, the message
“LOCK” is displayed, and the DVD ship mode is set.
[DVD and CD Ship Mode (Memory Clear)]• This mode moves the pickup to the position durable to
vibration. Use this mode when returning the set to the customerafter repair.
Procedure:1. Press the `/1 button to turn the power ON.2. Press three buttons of x , [DISPLAY] and [DIRECTION] simul-
taneously.3. After the “STANDBY” display blinks 15 times, the message
“LOCK” is displayed, and the DVD ship mode is set.
20
HCD-GNZ5D
DVD SECTION4-4. MIRROR TIME ADJUSTMENT
To enter Mirror Time Adjustment, press 5 “R” button on the remotecommander. The screen will appear as below.
There are five main commands in the Mirr time Adjust menu asshown in the figure above. The functions of each command aredescribed in the following page.
1. CD MIRR time CheckThis command checks the Mirror time value for CD disc.
2. DVD MIRR time CheckThis command checks the Mirror time value for DVD disc.
3. ThresholdThis command displays the threshold value between CD and DVDmirror time.
4. Save to EEPROMThis command saves an adjusted mirror time value to the EEPROM.
5. Default set MIRR timeThis command will set CD and DVD mirror time to firmware defaultvalue.
[Open] / [Close]Pressing the A button controls the tray for disc changeduring mirror time adjustment.[0] Return to previous menuPress 0 “R” button to return to previous menu.
4-4-1. EXECUTING MIRROR TIME ADJUSTMENT
In order to execute mirror time adjustment, the following standardprocedures must be followed.
(1) In standby mode, press three buttons x , A and [VOLUME +]
simultaneously.(2) Select “2. Drive Manual Operation”.
MIRR time Adjust Menu
1. CD MIRR time Check:2. DVD MIRR time Check:3. Threshold:4. Save to EEPROM5. Default set MIRR time
[Open] Tray open [Close] Tray close[0] Return to previous menu
Remocon Diagnosis Menu
0. External Chip Check1. Servo Parameter Check2. Drive Manual Operation3. Emergency History Check4. Version information5. Video Level Adjustment
Model : GVLXD_xxIF-con : Ver. xx.xx (xxxx)Syscon : Ver. x.xxx
Ver. 1.1
[TEST DISC LIST]Be sure to use the DVD disc that matches the signal standards ofyour region.• CD
YEDS-18 (Part No.: 3-702-101-01)PATD-012 (Part No.: 4-225-203-01)
• DVD SL (Single Layer) NTSC : HLX-503 (Part No.: J-6090-069-A)
HLX-504 (Part No.: J-6090-088-A) PAL : HLX-506 (Part No.: J-6090-077-A)• DVD DL (Dual Layer) NTSC : HLX-501 (Part No.: J-6090-071-A)
HLX-505 (Part No.: J-6090-089-A) PAL : HLX-507 (Part No.: J-6090-078-A)
4-1. GENERAL DESCRIPTION
The Mirror Time and IOP measurement allows you to makediagnosis and adjustment simply by using the remote commanderand monitor TV. The instructions, diagnosis results, etc. are givenon the on screen display (OSD).
The Mirror Time and IOP measurement is required is such eventswhere servicing a DVD-Player includes changing the Base Unit(BU). For each new BU to be used with a certain MV-044 board,Mirror Time and IOP measurement need to be carried out.
4-2. STARTING TEST MODE
Press three buttons x , A and [VOLUME +] simultaneouslywith the DVD player in standby mode.The Test Mode starts, then the menu shown below will bedisplayed on the TV screen.
The menu above is the Remocon Diagnosis Menu screen whichconsists of six main function. At the bottom of the menu screen,the model name and IF-con version. To enter Mirror TimeAdjustment menu, press button 2 “R” on the remote commanderto enter Drive Manual Operation menu. To exit from the Test Mode,press the power button on the remote commander.
4-3. DRIVE MANUAL OPERATION
The Drive Manual Operation menu consists of five mainfunction. By pressing 2 “R” button on the remote commander inthe Remocon Diagnosis Menu, the screen will appear as below.
Remocon Diagnosis Menu
0. External Chip Check1. Servo Parameter Check2. Drive Manual Operation3. Emergency History4. Version Information5. Video Level Adjustment
Model Name : GVLXD_XXIF-con : VSyscon : Ver.
er. xx.xx (xxxx)x.xxx
Drive Manual Operation
1. Servo Control2. Track/Layer Jump3. Manual Adjustment4. Tray Aging Mode5. MIRR time Adjust0. Return to Top Menu
21
HCD-GNZ5D
(3) Select “5. MIRR time Adjust”.
(4) Select “5. Default set MIRR time”.
(5) Select “3. Threshold”.
(6) Confirm the number. If it is 7D, go to next step. If it is any other value, return to step 4.
(7) Push A button to eject tray.
(8) Insert Test Disc HLX-504 into tray.
(9) Push A button to close tray.
(10) Push “2. DVD MIRR time Check”.
(11) Wait for HEX number to display.
(12) Confirm the number, if XX is 28 ~ 70, proceed with next step. If no, return to 8.
(13) Push “4. Save to EEPROM”.
Drive Manual Operation
1. Servo Control2. Track/Layer Jump3. Manual Adjustment4. Mecha test mode5. MIRR time Adjust0. Return to Top Menu
MIRR time Adjust Menu
1. CD MIRR time Check:2. DVD MIRR time Check:3. Threshold:4. Save to EEPROM:5. Default set MIRR time:
[Open] Tray open [Close] Tray close[0] Return to previous menu
MIRR time Adjust Menu
1. CD MIRR time Check:2. DVD MIRR time Check:3. Threshold: 7D4. Save to EEPROM:5. Default set MIRR time:
[Open] Tray open [Close] Tray close[0] Return to previous menu
MIRR time Adjust Menu
1. CD MIRR time Check:2. DVD MIRR time Check: xx xx3. Thereshold:4. Save to EEPROM:5. Default set MIRR time:
[Open] tray open [close] Tray close[0] Return to previous menu
(14) Confirm the same values are displayed. If it is not same, return to step 7.
(15) Push A button to eject tray.
(16) Take out HLX-504 and insert Test Disc YEDS-18 into tray.
(17) Push A button to close tray.
(18) Push “1. CD MIRR time check”.
(19) Wait for HEX number to display.
(20) Confirm the number, if YY is 5A ~ E8, proceed with next step. If no, return to 15.
(21) Push “4. Save to EEPROM”.
(22) Confirm the same values are displayed. If it is not the same, return to step 15.
(23) Push A button to eject tray.
(24) Remove Test Disc YEDS-18 from tray.
(25) Push A button to close tray.
(26) Press 0 “R” button to the Drive Manual Operation menu.
(27) Press 0 “R” button to return to the Remocon DiagnosisMenu.
(28) Press the ?/1 button to switch OFF set.
MIRR time Adjust Menu
1. CD MIRR time Check:2. DVD MIRR time Check: XX XX3. Threshold:4. Save to EEPROM:5. Default set MIRR time:
[Open] Tray open [close] Tray close[0] Return to previous menu
MIRR time Adjust Menu
1. CD MIRR time Check: yy YY2. DVD MIRR time Check: XX XX3. Threshold:4. Save to EEPROM:5. Default set MIRR time:
[Open] Tray open [close] Tray close[0] Return to previous menu
MIRR time Adjust Menu
1. CD MIRR time check: YY YY2. DVD MIRR time check: XX XX3. Threshold:4. Save to EEPROM:5. Default set MIRR time:
[Open] Tray open [close] Tray close[0] Return to previous menu
22
HCD-GNZ5D
4-5. EXECUTING IOP MEASUREMENT
In order to execute mirror time adjustment, the following standardprocedures must be followed.
(1) In standby mode, press three buttons x , A and[VOLUME +] simultaneously.
(2) Select “2. Drive Manual Operation” by pressing the 2 “R”button on the remote commander. The screen will appear as
below.
(3) Select “3. Manual Adjustment” by pressing the 3 “R” buttonon the remote commander. The screen will appear as below.
(4) Select Iop by pressing 6 “R” button on the remote commander.
Remocon Diagnosis Menu
0. External Chip Check1. Servo Parameter Check2. Drive Manual Operation3. Emergency History Check4. Version information5. Video Level Adjustment
Model : GVLXD XXIF-con Ver : XX.XX (XXXX)Syscon Ver : X.XX
Drive Manual Operation
1. Servo Control2. Track/Layer Jump3. Manual Adjustment4. Tray Aging Mode5. MIRR time adjust0. Return to top Menu
Manual Adjust
1. Track Balance Adjust:2. Track Gain Adjust:3. Focus Balance Adjust:4. Focus Gain Adjust:5. Eg boost Adjust:6. Iop:7. TRV. Level:8. S curve(FE) Level:9. RFL(PI) Level:0. MIRR Time:
o O Change Value[RETURN] Return to previous menu
(5) Wait until a hexadecimal number appear.
(6) Convert each data from hexadecimal to decimal using conversion table.
(7) Substract between these two values.
(8) If the remainder is smaller than 93 (decimal), then it is OK. However if the value is higher than 93, then the BU is defective and need to be change.
(9) Press RETURN “R” button to return back to previous menu.
(10) Press 0 “R” button to return to Top Menu and power OFFthe DVD Player.
Manual Adjust
1. Track Balance Adjust:2. Track Gain Adjust:3. Focus Balance Adjust:4. Focus Gain Adjust:5. Eq Boost Adjust:6. Iop. 5B:7. TRV. Level:8. S curve(FE) Level:9. RFL(PI) Level:0. MIRR Time:
Change Value[0] Return to previous menu
23
HCD-GNZ5DSECTION 5
MECHANICAL ADJUSTMENTS
Precaution1. Clean the following parts with a denatured alcohol-moistened
swab:record/playback heads pinch rollerserase head rubber beltscapstan idlers
2. Demagnetize the record/playback head with a headdemagnetizer.
3. Do not use a magnetized screwdriver for the adjustments.4. After the adjustments, apply suitable locking compound to the
parts adjusted.5. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
Torque Measurement
3.06 N • m to 6.96 N • m31 to 71 g • cm
(0.43 – 0.98 oz • inch)
0.19 N • m to 0.58 N • m2 to 6 g • cm
(0.02 – 0.08 oz • inch)
3.06 N • m to 6.96 N • m31 to 71 g • cm
(0.43 – 0.98 oz • inch)
0.19 N • m to 0.58 N • m2 to 6 g • cm
(0.02 – 0.08 oz • inch)
6.96 N • m to 14.02 N • m71 to 143 g • cm
(0.98 – 1.99 oz • inch)
9.80 N • m100 g or more
(3.53 oz or more)
9.80 N • m100 g or more
(3.53 oz or more)
Mode Torque meter
CQ-102C
CQ-102C
CQ-102RC
CQ-102RC
CQ-201B
CQ-403A
CQ-403R
Meter reading
FWD
FWDback tension
REV
REVback tension
FF/REW
FWD tension
REV tension
24
HCD-GNZ5DSECTION 6
ELECTRICAL ADJUSTMENTS
VIDEO SECTION
Video Level Check (VIDEO BOARD)PurposeThis adjustment is made to satisfy the NTSC standard, and if notadjusted correctly, the brightness will be too large or small.
Procedure:1. Connect oscilloscope to VIDEO output.2. Load a DVD reference disc playback.3. Check the video signal level is 1.00±0.07Vp-p.
DVD SECTION
When the base unit is replaced, perform the adjustment and themeasurement as shown below in this order.
1) MIRROR TIME ADJUSTMENT (See page 20)2) EXECUTING IOP MEASUREMENT (See page 22)
[TEST DISC LIST]Be sure to use the DVD disc that matches the signal standards ofyour region.• CD
YEDS-18 (Part No.: 3-702-101-01)PATD-012 (Part No.: 4-225-203-01)
• DVD SL (Single Layer) NTSC : HLX-503 (Part No.: J-6090-069-A)
HLX-504 (Part No.: J-6090-088-A) PAL : HLX-506 (Part No.: J-6090-077-A)• DVD DL (Dual Layer) NTSC : HLX-501 (Part No.: J-6090-071-A)
HLX-505 (Part No.: J-6090-089-A) PAL : HLX-507 (Part No.: J-6090-078-A)
[RFMON Level Check]Connection:
Procedure:1. Connect an oscilloscope to CN105 pin 6 (RFMON) and
CN105 pin 3 (GND) on the DMB11 board.2. Turn the power on.3. Set the test disc (refer to the TEST DISC LIST) on the tray
and press H button to playback.4. Confirm that oscilloscope waveform is clear and check
RFMON signal level is correct or not.Note: A clear RFMON signal waveform means that the shape “◊” can be
clearly distinguished at the center of the waveform.
+–
CN105 pin 6 (RFMON)CN105 pin 3 (GND)
oscilloscope
DMB11 board
VOLT/DIV: 200 mVTIME/DIV: 500 ns
RFMON signal waveform
level: 0.58 ± 1.23 Vp-p (DVD) 0.57 ± 1.1 Vp-p (CD)
oscilloscope
set
J801VIDEO OUTPUT
75 Ω
1.00 ± 0.07 Vp-p
(WHITE 100%)
Ver. 1.1
Checking Location: DMB10 board (Side A)
IC102
IC101
IC104
IC201
CN105CN106
CN105 pin 3 (GND)CN105 pin 6 (RFMON)
16
25
HCD-GNZ5D
0 dB=0.775 VDECK SECTION
1. Demagnetize the record/playback head with a headdemagnetizer.
2. Do not use a magnetized screwdriver for the adjustments.3. After the adjustments, apply suitable locking compound to the
parts adjust.4. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.5. The adjustments should be performed in the order given in this
service manual. (As a general rule, playback circuit adjustmentshould be completed before performing recording circuitadjustment.)
6. The adjustments should be performed for both L-CH and R-CH.
7. Switches and controls should be set as follows unless otherwisespecified.
• Test Tape
Record/Playback Head Azimuth Adjustment
Note: Perform this adjustments for both decksProcedure:1. Mode: Playback
Tape Signal Used forP-4-A063 6.3 kHz, –10 dB Azimuth Adjustment
DECK A DECK B
2. Turn the adjustment screw and check output peaks. If the peaksdo not match for L-CH and R-CH, turn the adjustment screwso that outputs match within 1dB of peak.
3. Mode: Playback
4. After the adjustments, apply suitable locking compound to thepats adjusted.
Adjustment Location: Playback Head (Deck A).Record/Playback/Erase Head (Deck B).
set
AUDIO boardIC201Pin 28 (L-CH)Pin 37 (R-CH)
AUDIO boardIC201Pin 38 (GND)
+–
level meter
test tapeP-4-A063(6.3 kHz, –10 dB)
screwposition
L-CHpeak
within1dB
outputlevel
L-CHpeak
R-CHpeak
within1dB
screwposition
R-CHpeak
AUDIOboardIC201
test tapeP-4-A063(6.3 kHz, –10 dB)
pin 37
oscilloscope
L-CH
R-CH
V H
waveform of oscilloscope
in phase 45° 90° 135° 180°
good wrong
pin 38
pin 28
L
R
reverseforward
Ver. 1.1
26
HCD-GNZ5D
7-1. CIRCUIT BOARDS LOCATION
SECTION 7DIAGRAMS
SUB TRANS board
JACK board
PANEL board
TRANS board
STREAM board
AUDIO board
FRONT AMP board
LEAD PIN board
SIRCS board
DRIVER board
SW board
DMB11 board
MOTOR (LD) board
MOTOR (TB) board
SENSOR board
VIDEO board
OPTICAL board
POWER SWITCHING
27 27
HCD-GNZ5D
HCD-GNZ5D
7-2. BLOCK DIAGRAM — RF/SERVO SECTION —
: CD PLAY
: DVD PLAY
: SACD PLAY
• Signal Path
DETECTOR
6
2345
1110
19
18
252 253
DVDRFIP
DVDADVDBDVDCDVDD
TPI
TNI
MCMD
CD
LD01
MD12
LD02
MSW
MD11
OSP OSN
CD/DVD RF AMP,FOCUS/TRACKING ERROR AMP
DVD SYSTEM PROCESSORDIGITAL SERVO PROCESSOR
IC102(1/2)
OPTICAL PICK-UPBLOCK
2AXISDEVICEFOCUS/
TRACKINGCOIL
23
20
LI M SW176
22
50
21
36 48
43
37 1
Q102 (2/2)AUTOMATIC POWERCONTROL (FOR DVD)
Q101, Q103VOLUME CONTROL
Q102 (1/2)AUTOMATIC POWERCONTROL (FOR CD)
LASERDIODE
(FOR CD)
LASERDIODE
(FOR DVD)
FOCUS COILDRIVE
4241
BUFFER
35 334 4
TRACKING COILDRIVE
32
3842
3741
30
47
SLED MOTORDRIVE
FOCUS/TRACKING COIL DRIVER,SPINDLE, SLED MOTOR DRIVER
IC201
2728
SPINDLE MOTORDRIVEMMSPINDLE
4647
FMOFOO
MIC
DMOTRO
V REFO
SPFG
40 IOPMON
FOO
RF
ABCD
F
E
CD LD
PD
LIMIT
WR650
VR780
MSW
DVD LD
FCS+FCS–
TRK+
VCC
TRK–
SP+SP–
SL+SL–
D C B A
V1P4
V1P4
9 NBB
8 NAA
3029 SLED MOTOR
DRIVEMM
BUFFER
19202221
40
45
SYSTEMCONTROLIC101(1/3)
99IFCK MTK_CLK29
100XIFCS MTK_CS30
110PRST MTK_XRST23
98IFSDO MTK_IN28101IFSDI
105IFBSY
KRMOD/HSYNCMREQ
MTK BUSY24
KARAOKE/MTK-REQ87
MTK_OUT27
TRO
FMOFOO
DMOTRO
1013
FMODMO
211 MUTE123210 MUTE170 TSDM
207114
MIC/VSYNC 205 A MAINSECTION
SLED
(Page 29)
2828
HCD-GNZ5D
HCD-GNZ5D
7-3. BLOCK DIAGRAM — VIDEO SECTION —
DVD SYSTEM PROCESSORIC102(2/2)
217ASDAT0ASDAT1ASDAT2ASDAT4
225SDPIF
EEPROMIC103
6 5
SCL
SDA
CE WEOE
FLASH ROMIC101
125-123, 121, 120, 118,117, 115, 135, 133-128, 126
146, 147, 149-151,158-160, 162, 164-166
22-26,29-35
HIGHA0-7IOA0-7, IOA18-IOA20A16, A17AD0 – AD7
A1-A
20
DATA & ADDRESS BUS
DATA & ADDRESS BUS
81-84,86-88,91 53-61, 67-72, 74-76, 78, 89, 92, 93
HD0 – HD7 A0 – A21
HD0 – HD7 A0
2645CE W
E
28
OE
11
A0 – A19DQ15/A-1
77
IOCS
IOW
A
79
IOUE
66
DQ0 – DQ7
RCLK
CE WE
OE
SDRAMIC104
38
DRCL
K
RD0 – RD15 RA0 – RA11
RA0 – RA11RD0 – RD15
142
RCS
19
RCS
138
RWE
16
RWE
140
RAS
18
RAS
139
CAS
17
CAS
MDQ
M0
15
DQM
0M
DQM
1
39
DQM
1CK
E
37
DRCK
E
102
SCL
103
SDA
143
BA0
20
BS0
BA1
21
BS1
29,31,33,35,38,40,42,44 25-16, 9-1, 48
145 156 113 137 157
2,4,5,7,8,10,11,13,42,44,45,47,48,50,51,53
218
D/A CONVERTERIC301
J801VIDEOOUT
IC3711
219222
198YUV3
220XRST215ACLK214ABCK213ALRCK
14 SDTI1
4 IN
VIDEO MUTE
2OUT3SAG
1PS
VIDEO AMPIC801
15 SDTI216 SDTI313 SDTI4
8 PDN10 MCLK9 BICK17 LRCK
19 SCL20 SDA
38DOWNMIX L
37
2FRONT L
1
DIGITALOPTICAL
TRANSMITTERIC306
DIGITALOUT
OPTICAL
LOUT4+LOUT4–
(DMIXL)
LOUT1+LOUT1–
(FL)
B MAINSECTION
C MAINSECTION
XTALI
XTALO
229
228
X10127MHz
IC3771
• Signal Path
: VIDEO
: Y
: COMPONENT VIDEO
: AUDIO
: DIGITAL
(Page 29)
(Page 29)
29 29
HCD-GNZ5D
HCD-GNZ5D
7-4. BLOCK DIAGRAM — MAIN SECTION —
17REC(DECK B)
PB(DECK A)
PB(DECK B)
TUNER
DOWN MIX L
MIC
76
RELAYSWITCH
3
4
75
L
R
FANSWITCH
BIAS OSCQ601
T601
B VIDEOSECTION
R-CH
HFUNCTION/
POWERSECTION
ARF/SERVOSECTION
CVIDEOSECTION
1
2
FRONT L 57
NEGPOS
IC701
M751(LOADING)
M741(TABLE)
LOADINGMOTORDRIVE
M
NEGPOS
IC712
TABLEMOTORDRIVE
M
LOD
TBL
Q731IC731TABLE
ADDRESSSENSOR
RE701DISC TRAYADDRESS
DETECT
CLOSE OPEN
S751OPEN/CLOSE
DETECT
R-CH
A+9V
MIC
3 1
35 34
DATA
CLOC
KDA
TACL
OCK
88VACS/
ILLUMI
VACS2 8
CDM EJECT/PROTECT 95
AC DET
AC4
6VIDEO MUTE VIDEO MUTE
8TA MUTE9HP MUTE6FUN ON/OFF
12FUN CTRL7FRONT RELAY
86 BIAS
PB B
DMSUR1
INB1
PB A
REC
28LOUT
27BBB125
53
BBA1
POWER AMPIC401
REC/PB AMP,SOUND CONTROLLER
IC201
SYSEM CONTORLIC101 (2/3)
76
15
13OVERLOAD
DETQ401
5
TM901
LCH
6DI8DO
4+9V
3RCH
DBFBDET AC
DET
DBFBSWITCH
Q212
R-CH
PROTECTDET
R-CH
Q282,283
+VH
RY481
FRONTSPEAKER
TM401
Q272
Q271Q402,403
MUTEQ701
IN
ST-BY
+RE-RE
AC DETD763,Q721-723
D753
SWITCHQ281
MUTEQ703
MUTECONTROL
Q791-795,797
Q481,482R-CH
R-CH
OVERHEATDET
TH401,Q416,417
AC DET
J1002
RV1001
MIC 1
MIC LEVEL
MIC AMPIC1001 (1/2)
MIC AMPIC1001 (2/2)
69 DIN70 DOUT71 CLK68 CE
ST
19 TUNED
97 CDM ENC0/1/2
100 CDMTBL-SENS
R-CH
Q602,603
Q627,Q628
A+9V
ERASEHEAD
REC/PBHEAD R-CH
R-CHPB
HEAD
MUTE CONTROLQ629-631
MUTE CONTROLQ623,624
MUTEQ622
J1004PHONES
R-CH
AC3
FAN901FAN
(DECK A)
HP901
HRPE901
(DECK B)
TAPEMECHANISM
DECK BLOCK
SHUT(B)84SHUT(A)83PLAY SW(A)&(B)/A-HALF82
85
79
B-HALF/REC
TRG(A)A SOL
REC(REV)
B PHOTOA PHOTOB MODEA MODEB HALFA HALF
REC(FWD)
TRG(B)B SOL 78
CAP M+
B SOL DRIVEQ101,102
CAP M DRIVEQ103,104
A SOL DRIVEQ105,106
7CL9CE
TUNED 1
DOUTDIN
CLKCETUNED IC203
3
4
59
AM
ANTENNA
FM 75ΩCOAXIAL
MUTE CONTROLQ729
HP SW
MIC 21 PB/REC
1920
1718
24 CAPM SW
SIGNAL IN/OUT CONTROLIC102 (1/2)
MUTECONTROL
Q728
79
42
79
42
• Signal Path
: TUNER
: AUDIO
: PB (DECK A)
: PB (DECK B)
: REC (DECK B)
: VIDEO
: COMPONENT VIDEO
• R-CH is omitted due to same as L-CH.
(Page 28)
(Page 27)
(Page 28)
(Page 30)
3030
HCD-GNZ5D
HCD-GNZ5D
7-5. BLOCK DIAGRAM — FUNCTION/POWER SECTION —
AC INRY901
T911POWER
TRANSFORMER
DVDM +9V
M +9V
A +9V
75CLK76DI1 STBY
RELAY
P1I
P21
73LATCH77RST
CLKDI1
LATCHRSTB
326
42
SYSTEM CONTROLIC101 (3/3)
VCC CONT
HP SW
72
44-51,53-61,
6365-67
D110I/1
SIRCS 7D117,118
RINGILLUMINATION
FUNCTIONKEY
S11,12,14-20
REMOTE CONTROLRECEIVER
94
S31-33,34,35,38,101
93
S51-57
92
89
74
4 STANDBYLED
12 RESET
LED+9V
+VF
20 AC CUT
43 – 31
X10232.768kHz
11
10
XCOUT
XCIN
13
15X101
16MHzXOUT
XIN
ILLUMI 1/4
WAKE UP0
KEY2
VOL(A)&(B)/SW IN
KEY1
KEY0
+VH
-VH
D471 F914
F915
F910
+VF
DVD +5V
D +3.3V D +3.3V
LED +9V
DVD POWER 22
UNREG+20V
UNREG+15V
D751 F918
D761 F919
D911
D+3.3V EVER+4V
-VP
EVER+4V
VCC+3.3V+3.3VREG
IC105 +3.3V
RF+3.3VREG
IC107
DVD+3.3VREG
IC851
DVD POWERCONTROLQ861,870
RF +3.3V
DVD +3.3V
DVD +5VDVD+5V
REGIC861
DVDM+9VREG
IC941
M+9VREG
IC942
A+9VREG
IC943
DVD POWERCONTROLQ771,772
POWERCONTROLQ108,109
DVD+5VREG
IC771
ILLUMINATIONCONTROL
Q11118
RESETSWITCH
Q107
RESETIC103
D+4VREG
IC945
B-SWITCH
Q902
POWERSWITCHING
D+4V
D+4V
EVER+4V
+3.3VRF+1.8V
REGIC106
RF +1.8V
5
SIGNAL IN/OUT CONTROLIC102 (2/2)
FL101FLUORESCENT
INDICATORTUBE
RELAYDRIVEQ901
HMAINSECTION
ENCODER
S102
MASTER VOLUME
FUNCTIONKEY
FUNCTIONKEY
G1-13D101
D102
E3,E15,PH MODEL
E3,E15,PH MODEL
E3,E15,PH MODEL
E12,E13AUS
E12,E13 MODEL
E12,E13 MODEL
IC104
S901VOLTAGE SELECTOR
230-240230-240V
220V
120V
220120
(Page 29)
31 31
HCD-GNZ5D
HCD-GNZ5D
• NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
Note on Printed Wiring Board:• X : parts extracted from the component side.• Y : parts extracted from the conductor side.• : Pattern from the side which enables seeing.
(The other layer’s patterns are not indicated.)
Caution:Pattern face side: Parts on the pattern face side seen from(Conductor Side) the pattern face are indicated.Parts face side: Parts on the parts face side seen from(Component Side) the parts face are indicated.
• Indication of transistor.• A : B+ Line.• B : B– Line.• Voltage and waveforms are dc with respect to ground
under no-signal (detuned) conditions.no mark : FM
∗ : Impossible to measure• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal produc-tion tolerances.
• Waveforms are taken with a oscilloscope.Voltage variations may be noted due to normal produc-tion tolerances.
• Circled numbers refer to waveforms.• Signal path.
F : AUDIOf : TUNERL : VIDEO (COMPONENT)r : VIDEO (COMPOSITE)E : TAPE PLAY (DECK A)d : TAPE PLAY (DECK B)G : TAPE REC (DECK B)J : DVD (AUDIO)c : DVD (RF)I : DVD (DIGITAL)
• AbbreviationE3 : 240 V AC area in E modelE12 : 220 – 240 V AC area in E modelE13 : 220 – 230 V AC area in E modelE15 : Iran modelPH : Philippine model
Note: The components identified by mark 0 or dotted linewith mark 0 are critical for safety.Replace only with part number specified.
UNLEADED SOLDERBoards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARKUnleaded solder has the following characteristics.• Unleaded solder melts at a temperature about 40 °C higher than
ordinary solder.Ordinary soldering irons can be used but the iron tip has to beapplied to the solder joint for a slightly longer time.Soldering irons using a temperature regulator should be set to about350 °C.Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow) thanordinary solder so use caution not to let solder bridges occur suchas on IC pins, etc.
• Usable with ordinary solderIt is best to use only unleaded solder but unleaded solder may alsobe added to ordinary solder.
C
B
These are omitted.
E
Q
B
These are omitted.
C E
Q
B
These are omitted.
C E
Q
Note on Schematic Diagram:• All capacitors are in µF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolyticsand tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.• 2 : nonflammable resistor.• C : panel designation.
1 IC102 6 (DVDRFIP)
0.5 Vp-p
200 mV/DIV, 100 nsec/DIV
500 mV/DIV, 20 µsec/DIV
2 IC102 ea (FED)
100 mV/DIV, 1 msec/DIV
6 IC102 <z., (YUV3)
500 mV/DIV, 20 µsec/DIV
3 IC102 es (TEO)
500 mV/DIV, 1 msec/DIV
7 IC102 <xx. (YUV1)
500 mV/DIV, 20 µsec/DIV
1.8 Vp-p
4 IC102 <z.v (YUV1)
500 mV/DIV, 20 µsec/DIV
5 IC102 <z.n (YUV2)
700 mVp-p
0.3 Vp-p
1.3 Vp-pH
H 1.2 Vp-p
H 1.5 Vp-p
37 nsec
1.1 Vp-p
32.768 kHz
1 IC101 q; (X CIN)
0.5 V/DIV, 20 µsec/DIV
0.6 Vp-p
16 MHz
2 IC101 qd (X OUT)
0.5 V/DIV, 0.5 µsec/DIV
• WAVEFORMS
– DMB11 BOARD –
– PANEL BOARD –
3232
HCD-GNZ5D
HCD-GNZ5D
7-6. PRINTED WIRING BOARDS — DRIVER SECTION — • Refer to page 26 for Circuit Boards Location. : Uses unleaded solder.
Ref. No. LocationD701 D-6D711 D-7
IC701 E-6IC712 E-7IC731 E-11
Q731 C-9
• SemiconductorLocation
1
A
B
C
D
E
F
G
H
2 3 4 5 6 7 8 9 10 11 12 13 14
(OPEN/CLOSE DETECT)
(DISC TRAY ADDRESS DETECT)
1
9
1
9
1
4
1
21 2
CN751S751
IC731
CN731
CN741
CN74
2
CN72
1
PANELBOARDCN102A
C715
C731
C735
C736
R70
1
R711
R731
R721
R722
R723
R73
5
R73
2
R733
R73
4
D70
1
D71
1
C751
IC712IC701
CN704
C737
R71
3
R712
C741
R70
2
JW702
JW703
JW704
JW705
JW706
JW707
JW70
8
JW711CN703
CN702 CN705
R751
C752
JW712
JW701
JW70
9
JW710
JW713
JW714
CN70
1
Q731
B E
(Page 50)
33 33
HCD-GNZ5D
HCD-GNZ5D
7-7. SCHEMATIC DIAGRAM — DRIVER SECTION — • Refer to page 56 for IC Block Diagrams.
IC B/D
IC B/D
R751
C752CN705
CN704CN721
CN751
C751
IC701
IC712
R701
R713
R711
R723 R721R722
C735C736C737
R735
R733R731
C731
Q731
C741
CN703
IC731CN731 CN741
CN742
C715
R702
R712
R732R734
D711
M751
M741
S751
CN701
D701
CN702
CN711
RE701
(Page 49)
3434
HCD-GNZ5D
HCD-GNZ5D
7-8. PRINTED WIRING BOARD — DMB11 SECTION — • Refer to page 26 for Circuit Boards Location. : Uses unleaded solder.
Ref. No. LocationD1001 H-6D3501 G-10D3502 F-10
IC101 D-4IC102 E-6IC103 G-7IC104 G-6(IC105) C-5IC106 I-6(IC107) C-8IC201 G-4(IC301) H-8(IC3711) H-9(IC3771) G-9
(Q101) B-7(Q102) B-6Q103 B-7Q3801 F-9
• SemiconductorLocation
( ): SIDE B
1
A
B
C
D
E
F
G
H
I
J
2 3 4 5 6 7 8 9 10 11
OPTICAL PICK-UP BLOCK
EVIDEOBOARDCN801
DAUDIOBOARDCN301
1-865-736-
11
(11)
C VIDEO BOARD NO851
BPANELBOARDCN005
1716
A3A2A1
A4
A5
A6
A7
A9
A10
A11
A12
R31
8
A8
IC10
2
FB115
FB11
4 FB11
3
FB112
R36
53
IC20
1
R31
9
Q103
R11
6
R117
C224
R136
IC106
R14
2
IC104
IC103
R144
C222C221
R153
R155
C220
C219
C218
C215
IC10
1
C210
X101
R20
8
C208
CN10
5CN
106
CN201
CN401
R20
9
C206
C205
R21
0
R21
4
FB40
1
FB40
2
FB40
3
FB404D1001
FB40
5
FB40
6
R21
5
R216
R21
9
R22
4
FL40
2
C190
R23
3
R23
4
C180
C179
R161
R107
R101
C217
C102
C105
C402
C108
R189
C307
C305
R190
R19
1
C302
R192
R19
3
C153
C152
R11
01
C117
R1102
R11
05
R1108
R15
53
C138
C137
C135
R11
29
C133 C132
R11
68
C119
C118
C116
C112
R195
C306
C101
R197
C167
C170
C181
C187
C189
C177
R15
44
C403
C129
R15
2
C378
3
R15
50
R15
49
C378
2C3781
C3774
C377
3
C3772C3771
C370
7
R37
82R37
81
R4706
R4705
R1543
C3784
R3773
R3774
R37
75
R3776
R37
77
R3772
R3771
R37
78
R3783
R3784
R37
85
R3786
R37
87
C3801
R37
88
R38
02
R3801
C178
R3716
R37
17
R37
15
R3714
R3713
R37
18
R37
21
R37
22
R3723
R37
12
R3711
R3724
R37
25
D3502
D3501
CN30
2
C150
C3724
C372
3
C372
2
C3721
C3714
CN301
54
12
C371
3
C3712
C371
1
C370
1R
3728
R37
27
R3726
R1557
C3805
C380
3
FL40
1
R3803
C380
2
R38
04
Q38
01
C3804 BCE
RB1
12
CN101
B C E
RB1
13
RB108
RB107
FL40
3
FL107
FL10
1
R3805
(Page 50)
(Page 44)
(Page 44)
(Page 40)
Ver. 1.1
New part of EEP ROM (IC103) on the DMB11 board cannot be used. Therefore,if the mounted DMB11 board (A-1109-317-A, etc.) is replaced, exchange newEEP ROM (IC103) with that used before the replacement.
35 35
HCD-GNZ5D
HCD-GNZ5D
1
A
B
C
D
E
F
G
H
I
J
234567891011
1-865-736-
11
(11)
1
1
3
5
4
3
54
B5
B1
B4
B3
B7
B8
B2
B6
R50
05
R50
11
R50
16
R50
17
C114 C1
15C120
C121
C122
C123
C124
C125
C126
FB111
C130
R109
C139
C140
C146
C147
C148C1
49C151
C154
C156
C159
C161
C163
R10
5
R10
6
R12
3
C171
C172
C173
R110
R118
R120
R121
R187
R127
C193
C195
C301
R16
4
R169
R1133
R20
4R
205
R146
R151
R20
6
R20
7
R21
3 R22
0
R22
1
IC301
R22
3
R22
5
IC105
R22
6
R23
0
R231
R23
2
R1109
Q102
R246
R24
7
R1110
R196
R11
50
IC10
7
R1151
R1152
R1530
R1531
Q101
C214
C213
C212
R108
C211
R1540
R11
1
R112
R113
R114
R115
C209
R12
6
R124
C203
R1554
C191
R141
R143
C188
R16
0
C184
C182
R1552R
1134
R1126
R1123 C176
C175
C174
R31
4
R36
52
R1104
R1103
C164
R15
51
R25
04
R15
04
C106
C109
R15
02
C113
C127
C128
C131
C136
R104
C144
C158
C160
C162
C370
8
R1548
R4704
R4703
R4702
R4701
R1542
C192
R1547
C233
C196
R15
46
R37
19
R37
29
R37
79
R3789
R1524
R1526
R3501
IC37
71IC
3711
R321
R138
C370
2
FL108
RB1
03
FL10
5
RB106 RB105
RB1
11
RB1
04
FL10
6FL
104
R21
2
C155
3636
HCD-GNZ5D
HCD-GNZ5D
7-9. SCHEMATIC DIAGRAM — DMB11 SECTION (1/4) — • Refer to page 56 for IC Block Diagrams.
IC B/D
JL3505JL3506
JL3507JL3508JL3509
JL3510JL3511
JL3512JL3513
JL3514JL3515
JL3517JL3516
R319
R318
ICT301
C3804
R3802
C3803
JL3504JL3503
JL3502JL3501
C3805
C306
C307
IC3711
Q3801
IC3771
C3801
C301
C305
JL34
4
JL34
3
JL36
53
JL36
52JL
3651
JL345JL346
JL347JL348
JL349
C302 R3805R3804
R3803
R3781 R3783
R3782
R3784 C3782C3781
C3783R3785 R3786
R3787 R3788
C3708
C3707
C3773R3775
R3774
R3772
C3771
R3771 R3773
C3772
R3776
R3777
C3774
R3721 R3723
C3721 C3722
R3722
R3724 R3727
R3726R3725 C3723
C3702
C3701
R3712
R3714C3711 C3712
R3715 C3713
R3711 R3713
R3717
R3716
R3718
C3714
R3719
R3729
C3724
R3728
R3778
R3779
R3789
C3784
R3801
C3802
R3653
R3652
R314
IC301D3501
D3502
R3501
CN302
(Page 38)
(Page 39)
(Page 38)
(Page 41)
(Page 38)
(Page 39)
37 37
HCD-GNZ5D
HCD-GNZ5D
7-10. SCHEMATIC DIAGRAM — DMB11 SECTION (2/4) —
CL202
CL203
CL204
CL20
5
CL206
CL20
7
CL20
8
CL210
CL211
CL212
ICT207
JL201JL202JL203
JL204JL205
JL206
CL209
CL201
C217
C218C220
JL4601JL4602
JL4603JL4604JL4605JL4606
JL4607JL4608JL4609JL4610
CN401
R206
R207R204
C203
R205
R209
R210
R219 R224
C210
R216
C208
R215
C206
R214
C205
R208
R212
C233
R220
C209
R221
R223R225
C211 R234R230
C212
C214
C215
R233
C213
C222
C221
C219C224
CN201
R247
R246
R2504
R22
6
R23
1
R23
2R213
IC201
C402C403
FB406
FB405 FL402
FL403 FB403
FB404 FL401 FB402
FB401
(Page 38)
(Page 39)
(Page 39)
(Page 38)
(Page39)
(Page 39)
(Page 38)
(Page 39)
(Page 38)
(Page 39)
(Page 39)
(Page 38)
(Page 45)
3838
HCD-GNZ5D
HCD-GNZ5D
• Refer to page 59 for IC Pin Descriptions.7-11. SCHEMATIC DIAGRAM — DMB11 SECTION (3/4) — • Refer to page 31 for Waveforms.
R14
4
R15
2
R196
CL101
CL10
3
JL12
9
JL12
8
JL16
0
CL104
JL135
CL105
CL110CL109
CL108
ICT109
ICT112
ICT1
13
ICT114
ICT115
ICT117ICT118
ICT135
ICT136
JL101
JL102
JL130
JL167
JL127JL132
JL133
JL10
3
JL10
4
JL10
5
JL10
6
ICT1
33
JL113
JL136
JL13
7
JL17
1
JL161
JL162
JL16
8
JL16
9JL
170
JL163
JL16
4
JL17
2JL
173
JL16
5
JL16
6
ICT125
ICT131
ICT1501
R15
30
R15
31
C117
C119
C129
JL4701
JL4713
JL4712JL4711
JL4710
JL4709JL4708
JL4707JL4706
JL4705JL4704
JL4703JL4702
R1101R1553
R1123
R15
42
C116
C120C121
C122C123
C124
C130 C132
C133
C125
C126
C196
C128
C131
C136 C144
R16
1
R15
57
C160
C158C155
R15
47
R15
40
R15
48R
1549
R15
50
R15
1
R15
3R
155
R16
0
C163
C162
C164
C176
RB111
RB103
RB104
C174
C175
C173
C171
C170
R4706
R4705
R4704
R4703
R4702
R4701R321
R15
26
R15
24
C148C147
R15
51R13
6
C137
C135 C1
39C1
40
C146
C149
C150
R14
1
C151
R14
2
C154
R11
68C1
53
C152
C156
R1552
C161
R1543 R18
9R
190
R19
2
R19
7
R11
02
R19
5
R146
C127
C118
C115C114
RB108
RB107
R15
04
R138
C138
R14
3
RB113RB112
FL105
X101
R164
C159
R1103 R1104
CL138
R1105
R1108
C172
R1126R1554R1109
R127
IC102
CN301
(Page 36)
(Page 39)(Page 36)
(Page 39)
(Page 37)
(Page 37)
(Page 37)
(Page 39)
(Page 45)
(Page 36)
(Page 39)
(Page 37)
(Page 37)
(Page 39)
39 39
HCD-GNZ5D
HCD-GNZ5D
7-12. SCHEMATIC DIAGRAM — DMB11 SECTION (4/4) —
R109
R1133
R1134
R123
R126
R187
CL106
CL107
CL112
CL113
JL139
JL140
JL141JL142
JL143JL144
JL145
JL146JL147JL148
JL149JL150
JL151
JL152JL153JL154
JL155JL156JL157
JL158JL159
CL114CL115
CL116
CL117
CL118
ICT1
08
ICT110
ICT111
ICT121
ICT123
ICT124
ICT126
ICT127
ICT128
ICT129
ICT137
JL107
JL108JL109
JL110JL111JL112
JL114
JL138
JL115JL116
JL117JL118
JL119JL120
JL121JL122
JL123JL124
JL125
CL1501
C105
C177
C178 C187
CN101
CN105
D1001
IC104
CN106
R1544
C101
R108R111
R116
R117
R101
R114
R107
R1129
R105
R106
C102
C113C106
C195C193
C192
C108
C109R1150
R1546
R1152
R1151
C167
C180
C191
C179
RB105 RB106
C184R169
C182 C188
C189
R1110
C181
ICT107
ICT102
ICT101
ICT106
ICT105
ICT104
ICT103
C190
R104
R193 R191R11
3
R11
5
R11
2
R11
8
R12
0
R12
1
R12
4
C112
R110
Q102
IC103
IC105
R1502
FL101
IC107
Q103
Q101
FB115
FB114
FB113FB112
FB111
FL106
FL104
FL107
FL108
IC101
IC106
(Page 37)
(Page 37)
(Page 37)
(Page 37)
(Page 37)
(Page 38)
(Page 37)
(Page 37)(Page 36)
(Page 36)
(Page 38)
(Page 38)
(Page 38)
(Page 49)
(Page 38)
Ver. 1.1
New part of EEP ROM (IC103) on the DMB11 board cannot be used. Therefore,if the mounted DMB11 board (A-1109-317-A, etc.) is replaced, exchange newEEP ROM (IC103) with that used before the replacement.
4040
HCD-GNZ5D
HCD-GNZ5D
7-13. PRINTED WIRING BOARDS — AUDIO SECTION — • Refer to page 26 for Circuit Boards Location. : Uses unleaded solder.
1
A
B
C
D
E
F
G
H
I
2 3 4 5 6 7 8 9 10 11 12 13 14
1 3
C308
R30
4
IC30
6
C309
IC306
123
13
DIGITALOUT
OPTICAL
NO305
R384
FB30
1
JW291
JW293
R737
IC201
D72
6
R623
R798
R62
6
R625
C653C613C651C611
13 8 1
Q728
R32
3
C323
R317
R27
7R
276
R232
R35
3
R35
7
R657
R36
3
R65
2
R658 R740
C657
Q772
Q721
R769
Q792
R79
3
R79
1
R795
C793
R794
C794
D79
1
D792D793
Q793Q791
R74
1
R76
4
R76
2
R79
2C3
63
R74
2
R656
R35
5
C259
R252
C260
R25
3
Q70
3
C621
C262
Q70
4
R315R313
C201
R238
R255
R256
R254
D202
R20
1
R202
Q252
JR251
R21
4
R235
R215
Q212
JR211R
216
R351
C222C220 R
213
C218C219
R21
2
R237
R616
C617
R617
R236
R61
8
R620
R272
R27
1
IC203
R63
2
Q281
R60
2
R611
R23
1
D235
C622
R21
1
R25
1
R651
C728
D201
R613
Q272
R239
R653
R654
R655
R615
R614
C283
C623
Q621
R32
1
Q622
Q623
Q626
Q62
8
Q629
R62
2
R75
1
Q627
R624
R62
1
Q624
Q625 Q631R62
7
R628 R629
Q630
R63
9
R73
8
R601
C601C602
Q602
Q603 R603
R604
R73
9
R27
5
R31
1
R361
Q729
R79
0
Q722
D72
7
R26
1
Q723
Q795
R22
1
R262
R76
3
Q283
R72
1
JR30
4
R70
3
R70
4
R300
Q282
R222
C795
R753
JR30
5
C778
C258
Q702Q701
R70
2R
701
C624
R35
2R
312
R362
R752
R32
2
R72
3
R28
2
R612
R768
Q771
R27
3R
274
Q27
1D271
Q797
R79
6
R65
9
D753
D763
D72
8
C367C368
D762
R71
5
R71
7
C612 C652
C792
L302
3
1
1 17
JW301
JW113
JW116
JW11
7
JW11
8
JW12
4
JW126
JW133JW134
JW135
JW13
6JW
138
JW140
JW141JW142
JW14
4
JW14
5
JW14
7
JW15
1
JW15
5
JW156
JW15
7
JW15
8
JW159
JW16
0
JW162 JW163JW164JW165
JW166JW167
JW168
JW169
JW17
0
JW17
1JW
172
JW174
JW17
5JW177JW179
JW181JW182
JW183
JW18
5
JW186JW187
JW190
JW191
JW192
JW193
JW194
JW195
JW19
6JW
197
JW19
8JW
199
JW20
0
JW201
JW20
3JW204
JW20
6
JW20
7
JW20
9JW
210
JW21
4
JW21
5
JW216
JW218
JW219JW220 JW221
JW222 JW22
3JW224JW225
JW227
JW228JW229
JW230
JW23
1JW
232
JW233JW234
JW23
7JW
238
JW25
1JW
252
JW25
3
JW25
4JW
255
JW25
6
JW26
1
JW26
4
JW26
5
JW27
0JW27
2
JW27
3JW
274
JW27
8
JW279
JW28
4JW
285
JW28
6
JW28
8
JW28
9
JW290
JW29
5
JW29
7
JW29
8
JW303JW305
JW30
6JW
307
JW309
JW310 JW311
JW312JW313JW314JW315
JW316
JW317JW318JW319JW320
JW32
1JW
322
JW32
3
JW32
4JW
325
JW32
6
JW327
JW328JW329
JW33
0
JW331
JW332JW333
JW33
5JW
336
JW33
7
JW33
8
JW339JW341
JW342
JW343
JW344
JW345
JW346
JW347
JW348JW349
JW350JW351
JW352JW353
JW354
JW355
JW356JW357
JW358
JW359
JW360JW361JW362JW363
JW365
JW366
JW367
JW368
JW36
9
JW371
JW37
4
JW37
8JW
379
JW381
JW384
JW385
JW38
6JW
387
JW388
JW38
9
JW39
0
JW392JW393JW394
JW395JW396
JW397
JW398
JW39
9JW
400
JW40
1
JW40
3
JW40
6
JW40
7
JW40
8JW40
9
JW41
0
JW41
1JW
412
JW413
JW414
LP502
LP503
JW14
8
JW24
3JW
244
JW24
5JW
246
JW24
7JW
248
JW24
9
JW12
3
JW188
JW30
8
JW226
JW415
JW41
6
JW417
JW41
8
JW419
JW40
4
JW40
5
JW184
JW202
CN201
C351
CN75
4
CN602
CN202
CN601
C265
C285
C352
C726
C658
C383
C791
Q79
4D76
1
D75
1
C763
C765
C356
C365
C362C316
C325
C322
C261
C312C263
C202
C224
C225
C274
C223
C221
C618
C620
D771
C236
C286
C253
C254
C256
C237
C226
C213
C239
C211
C753
C655
C656
C203
C204
C205
C251
C266
C616 C615
C228C268
C654 C614
EPT751
C229
C603
Q60
1
C273
T601
C605
CN75
3
R22
3
C771
C725
C764
IC771C772
CN75
1
CN301
C214
C269
R263
C282
C264
C281
C311
C361
C321
JW39
1
JW38
0
JW161
JW38
3
JW153
JW382
NO302B
1 4
1 4
1 4
NO302A
LP504
NO701
JW127
NO703
1 8
4 1
JW14
3JW
146
JW21
7JW268JW271
JW275
JW276
JW277
JW280JW282
JW28
3
JW373 JW372 JW375
JW42
0
JW42
1
CN755
JW281
JW340
JW26
9
C619
C659
LP506FAN901
JW12
9
CN75
2
JW30
4
JW364
JW29
6
JW287
JW235
JW25
7
JW125
JW422JW423
JW13
9
JW137
C604
JW154
JW263
JW26
7
JW26
2
JW26
0JW
259
JW25
8
JW25
0
JW23
6
JW24
0
JW24
1
JW24
2
JW29
9
JW21
1JW
212
JW21
3
JW189
JW176
JW18
0
JW114
JW115
JW11
2
JW11
9
JW120
JW12
1
JW12
2
JW128
JW130
JW131
JW14
9
JW30
0JW
302
JW334
JW11
1
JW26
6
JW15
0JW
152
JW17
3
JW23
9JW
132
JW376
CN30
4CN203
1
1
6
3
10
JACKBOARDNO1002
F
GJACK
BOARDNO1001
PANELBOARDCN003
H
PANELBOARDNO101
I
BLKERASE
HRPE901REC/PB/ERASE
HEAD(DECK B)
REC/PB(R-CH)
REC/PB(L-CH)
CN602
WHTREDBLK
WHTREDBLK
WHT
HRP901PB
HEAD(DECK A)
PB(L-CH)
PB(R-CH)
CN601
REDBLK
WHT
FRONT AMP BOARDCN402
J FRONT AMP BOARDCN401
K TRANS BOARDCN914
L
1-865-685-
14
14
1-865-697-
11
14
VIDEO BOARDCN851M
E
3
1
B
DMB11 BOARD CN302
D
TM901
(CHASSIS)
(Page 34)
(Page 51)
(Page 51)
(Page 50)
(Page 50)
(Page 46) (Page 46) (Page 54) (Page 44)
D201 D-5D202 D-5D235 F-11D271 H-4D726 C-8D727 C-7D728 C-7D751 G-10D753 G-8D761 G-9D762 B-7D763 G-8D771 B-8D791 I-11D792 I-12D793 I-12
IC201 E-5IC203 H-8IC306 C-14IC771 B-9
Q212 D-6Q252 C-5Q271 H-4Q272 H-3Q281 H-8Q282 H-8Q283 H-8Q601 G-5
Ref. No. Location
• Semiconductor LocationRef. No. LocationQ602 G-6Q603 G-5Q621 G-4Q622 G-4Q623 H-5Q624 H-5Q625 G-4Q626 H-4Q627 G-4Q628 G-4Q629 H-5Q630 H-5Q631 H-5Q701 I-8Q702 I-9Q703 G-11Q704 F-12Q721 B-6Q722 B-6Q723 B-5Q728 D-8Q729 D-7Q771 C-8Q772 C-8Q791 I-11Q792 I-11Q793 I-12Q794 H-12Q795 I-12Q797 H-12
41 41
HCD-GNZ5D
HCD-GNZ5D
7-14. SCHEMATIC DIAGRAM — AUDIO SECTION (1/3) —
C362
C322
R357
R311
R351
R312
R352
R321
R361
R322
R362
C321
C361
R740R741
R742
JR304 JR305
R768
R769
R236
R235 R238
R263
R703
R704
R723
R721
R739
R738 R737
CN753
C728
C778
NO302ANO302BCN755
JW417
C356
C316
C325
C365
C312
C352
C311
C351
R239R237 C239
C726
JW415 JW416
Q729
Q728
D771
D235R223
Q703
Q704
Q722 Q723
Q721
R353 R355
R313 R315 R317
C323
C363
CN301
C229
C269
R715
R717
JW301
R363
R323FB301CN304NO305
R304
C309C308
L302
D727
D726
D762
D728
IC306
C725
(Page 36)
(Page 52)
(Page 42)
4242
HCD-GNZ5D
HCD-GNZ5D
7-15. SCHEMATIC DIAGRAM — AUDIO SECTION (2/3) —
C223
C263
R215
R214
R216
R255
R254
R256
R201
C221C6
58C6
18
R639
CN602
C205C204
C266
R21
2
R62
0
R61
7
R23
2
TP20
1
TP20
0
C203
C213
C253
C237
C281C282C283
R271
C273
R275 R277 C274
R276
Q629
R621
R622
R221R261
C286
R611
R651
R652
R612
R272R273
R274
R659
C220
CN201
C254
C214
CN601
R616
R632
R21
1R
251
C259
C258
C218
C219
C620
R65
7
C654
C614
R282
R623
R624R626
R625C2
36
C262
C285
R231R658
C659
R253
C261
R656R252
C657
R213C222
C617
C619
R618
C211
C653
C613
R629
R628
R627
R604
R603C605
C603
R601
C602
C601
C616
C656
C622C621
C615
C251
R613
C623C624
C226
C655 R653
C264
C265
JR251
C611
C651
C201
C225
C224
JR211
JW293
R701
R702
C228
C268
T601
Q601
Q271
Q621
Q622
Q624
Q623
Q627
Q625
Q626Q628
Q630 Q631
R602
Q603
Q602
R655
R654
R615
R614
IC201C260
JW291
C202
Q282
Q283
IC203
Q281
Q701
Q272
D271
C612
C652
Q702C2
56
R202
C604
CN203
Q252
D201
D202
Q212
NO703
R222
R262
C368C367
(Page 41)
(Page 52)
(Page 43)
(Page 47)
(Page 45)
43 43
HCD-GNZ5D
HCD-GNZ5D
7-16. SCHEMATIC DIAGRAM — AUDIO SECTION (3/3) —
C763
C753
C791TP791
CN754
R795
R791
R792
C795
Q794
Q793C793
R794
CN202
C794
CN751
IC771
C772 C771
R790
R798
R763
C765R764R762
Q792
R793
C764
R753
R752
R796
CN752
NO701
R751
D753
D763
EPT751
FAN901
Q772
Q771
D761
D751
D792
D793
Q795
Q797
Q791
D791
(Page 49)
(Page 42)
(Page 47)
(Page 53)
(Page 48)
4444
HCD-GNZ5D
HCD-GNZ5D
7-17. PRINTED WIRING BOARD — VIDEO SECTION — • Refer to page 26 for Circuit Boards Location. : Uses unleaded solder.
1
A
B
C
D
E
F
G
H
I
2 3 4 5 6 7 8 9 10 11 12 13
(CHASSIS)
J801VIDEOOUT
1-866-974-
11
(11)
(CHASSIS)
MAUDIO BOARD NO703
CDMB11 BOARD CN401
EDMB11 BOARD CN301
IC8011
16
342345
C854
C851
Q87
0
Q86
1
C862
L861
L862
C863
D86
1
IC86
1
R861
C865
C856
C866
EP80
1
C840
EP85
1
C811
C802
L801
NO851
C872
LP851JW860
IC85
1
C853
R87
0
R87
1
JW85
2
R801
JW85
4
JW856C8
01
JW859
JW801
JW85
1
JW853
1
15
3
5
1
8 1
E
C
B
E
C
B
JW855
JW857
FB81
1C813
J801
R81
1
C841
C842
R81
2
C812
CN851
CN80
1
Ref. No. LocationD861 G-5
IC801 C-9IC851 E-6IC861 G-6
Q861 F-3Q870 F-2
• SemiconductorLocation
(Page 34)(Page 34)
(Page 40)
45 45
HCD-GNZ5D
HCD-GNZ5D
7-18. SCHEMATIC DIAGRAM — VIDEO SECTION —
IC B/D
C802L801
C862
C863C865
L861
L862R870
R871
C872
C840
C851
C812R811
C813
FB811
C841
C842
R801
C853 C854
IC851
IC801
IC861
R861 Q861
Q870
C801 R812
C856
C866
NO851
C811
EP801
EP851D861
CN851
CN801J801
(Page 37)
(Page 38)
(Page 42)
4646
HCD-GNZ5D
HCD-GNZ5D
D401 D-10D410 C-7D451 D-8D471 D-3D481 C-11D485 D-11D486 D-11D491 E-11
IC401 F-9IC941 F-6IC942 F-5
Ref. No. Location
• Semiconductor LocationRef. No. LocationIC943 F-4IC945 F-4
Q401 D-10Q402 E-5Q403 D-5Q416 E-11Q417 F-11Q451 D-9Q481 B-10Q482 B-11
7-19. PRINTED WIRING BOARD — FRONT AMP SECTION — • Refer to page 26 for Circuit Boards Location. : Uses unleaded solder.
1
A
B
C
D
E
F
2 3 4 5 6 7 8 9 10 11 12 13 14
1-865-686-
J
AUDIO BOARD CN202
AUDIO BOARD CN201
K
QTRANSBOARDCN915
13
(13)
(CHASSIS)
1 15
TM401FRONT
SPEAKER
R
L
E
BE
B
B
E
B
E
E
BE
B
1 4
1 3 1 3 1 3
B
B
E
E
1 4
NO471R
472 C4
71
C472
TM40
1
C485
C486
D481R480
R485
R486
JW481
JW482Q482
R487 R48
8
R489
R49
0
JW46
0
JW463
JW46
4
JW46
5
IC401
TH401
Q41
7R
415
R41
7
R41
8
R41
3
R41
4
C403
C453
CN401CN402
R44
0
IC941IC942IC943IC945
C949
C945 C946
C943C941
R94
1
R42
5
R426
R40
1R402
C401
C402
C452 R451R452
R45
3
R403
R40
4
R419
C408
C458
R46
1
C416
Q401
Q451D45
1
R408
R409
R41
0
C406C4
07
C456
C457
R458R459
R460
JW41
2
JW413
JW40
6
JW44
3
JW44
5
JW47
5
JW41
9JW
420
JW42
1
JW476
JW426JW427JW428
JW431
JW433JW434
JW472
JW43
6
JW43
8
JW44
0
JW44
8JW
449
JW453JW454
JW456
JW457
JW45
8
EP401
C942
JW40
1
JW414
R47
1
R411
JW423JW422
R42
0
JW41
8
R45
4
JW41
0
JW409
JW40
4
JW432
JW429
JW40
5
D485D486
JW461
D491
JW415
JW40
7
R43
9
JW44
2
JW41
1
JW41
6
R45
7R
407
JW41
7 D40
1
JW452
RY481
R412
R42
1
R42
7
Q40
2
R428R429R430
Q403 JW408
JW43
9
R40
6
R45
6
C944
C950
Q41
6
C421
JW44
4
JW40
3
C404C4
54
JW40
2
JW40
0
HS471
D471
C451
C410
R41
6
JW473
JW455D410
Q481
1 15 1 15
(Page 54)
(Page 40) (Page 40)
47 47
HCD-GNZ5D
HCD-GNZ5D
7-20. SCHEMATIC DIAGRAM — FRONT AMP SECTION —
R451
R401
R454
R439
R440
R489
R490
C451
C401
C416
C403
C453
D491
D481
TM401
IC942
IC943
JW482
JW481
R416
R429
Q402R406
CN401
CN402
C950
C946 C945
C944 C943
R941C942 C941
R452
R404
R402
R407
R408
R409
R458
D451R459
R457
R456
R460
R430R426
R410
R425
R428
R427
R413
R414
R421
Q417
R417R418
R412
TH401
C410R415
Q416
R471
R472
D485D486
R488
R487
NO471
R419
R420
R411
R461 C406
C407
C457
C456
C486
C485
D410
D401
RY481
R486 R485
EP401
Q401Q403
Q451
Q481
Q482
IC945
IC941
R403
C404
C454
R453
D471
R480
IC401
C949
C402
C452
C408 C458C421
C471
C472
(Page 43)
(Page 42)
(Page 53)
4848
HCD-GNZ5D
HCD-GNZ5D
7-21. SCHEMATIC DIAGRAM — PANEL SECTION (1/2) —
FB102
FB101
R027
R028R031
R032
JR112
JR111
JR110
JR109
S11
S32
S33
S34
S35
S57
S31
S38
S52
S53
S54
S55
S56
S51
R167 R148
R140
R095 R096
S12
S14
S15
S16
S17
S18
S19
S20
R166
R165R163
R161R160R159
R158R157
R156R155
R154R153
R151R150
R149
R147
R146R145
R144R143R142
R141
R139R138
R137R136
R135R134
R133R132R131
D11
4
R055R051
D11
3
R053
R152
R063
JR113
JR114
JR115
JR116
NO152 CN152
JR117
NO151 CN151
Q101 Q103 Q105
NO101
C128JR105
R052 R054 R056JR107
JR108
R037
R016
R025
R039
R038R036
R035R034
R033
R040
C102C101
D112
D111
R081R082R083R084R085R086
R068 R067 R062 R061
R041R042R043R044R045R046R047R048R049R050
CN004
R069
S102
S101
FL101
D117
D118
D101
D102
Q102 Q104 Q106
R066 R065 R064 R071 R070
R175
Q111
JR118
(Page 43)
(Page 49)
49 49
HCD-GNZ5D
HCD-GNZ5D
• Refer to page 57 for IC Pin Descriptions.7-22. SCHEMATIC DIAGRAM — PANEL SECTION (2/2) — • Refer to page 31 for Waveforms.
CN143 CN153
R11
7C1
03
C112
R12
0
R16
8
R197
R195C114
R200
R10
1
R11
9
R005
R017
C106
C105
R12
1
TP10
1
TP10
2
R013
R014R015
D109 R075
R076
D105
R074
R181
R11
8
R17
8R
179
R18
0
R10
2R
103
R10
5
R10
6
R10
8
R006
R018R019
R020
R12
2R
123
R12
4R
125
R12
6R
127
R12
8
R12
9R
130
R16
9R
170
R17
1
R182
R183R184
R185R186R187
R188R189
R007
R008R009
R010R011
R012
R078
R080
R077
R090R089
R087R088
CN002
C148
R199
R10
9
R198
D108
C120
R026
R024R023R022
R021
C116
JR10
4
TP104TP105
R16
2
R16
4
R10
7
D121
Q108
R079
R002
R057
R058
R029
R030
R001R110
JR102
R05
9
R06
0
C129
C130
C122
JR119
JR120
C152
C153
C154
JR121
C121
FB10
3
R194
R193R192
C146
C145
R072
R073
R10
4
R174
IC102
IC103
C147
R172
R173
CN003
CN102
CN005
C113
C127
C117C118C119 R004
R003
R11
1
R112
C110
C111
C104
FB104
R177
D110
JR101
JR106
IC104
CN001
Q107
X101
D106 D107
C126
C125
FB105
Q109
R113
R114
C115
X102
C144
JR123
R115
R116
IC101
(Page 39)
(Page 33)
(Page 43)
(Page 48)
5050
HCD-GNZ5D
HCD-GNZ5D
7-23. PRINTED WIRING BOARDS — PANEL SECTION — • Refer to page 26 for Circuit Boards Location. : Uses unleaded solder.
Ref. No. LocationD101 C-3D102 C-3D105 D-7D106 D-7D107 D-8D109 D-8D110 B-12D111 C-5D112 C-5D113 G-4D114 F-4D117 H-6D118 H-5D121 E-5
IC101 C-7IC102 D-4IC103 D-8IC104 H-11
Q101 G-5Q102 G-4Q103 G-5Q104 G-4Q105 G-5Q106 G-4Q107 D-8Q108 D-3Q109 D-3Q111 G-7
• SemiconductorLocation
1
A
B
C
D
E
F
G
H
I
J
2 3 4 5 6 7 8 9 10 11 12 13
IAUDIO BOARD CN751
HAUDIO BOARD CN752
A
DRIVER BOARD CN701
B
DMB11 BOARD CN106
TAPEMECHANISM
DECKBLOCK
1-865-681-
14
(14)
1-865-682-
12
(14)
1-865-683-
11
(14)
I/
X
3 1
117RING
ILLUMINATION
D118
MASTERVOLUME
S102
lOPERATIO DIALL
RINGILLUMINATION
3 1
5 4
1 3
1
2
13
12
3 1
1 4
18
R115R113
JR118
D114
IC101
D101
FB10
3R
117
C104
R12
0
R104
IC102
R199
R026
R10
1
R10
2R
103
R105R106
R20
0
R189
JR108
JR109
JR107
Q10
4
Q101
R018
Q103
Q105Q10
6
Q108
R05
2
R053
R019
R05
4
R02
0R022
R05
6
R021R023
C118C117
Q109
R06
4
R06
5R
066
R06
7R
068
R07
0
R071
CD SYNC
PRESET EQ
GROOVE
TAPEA/B
TUNER/BANDEQ BAND/
MEMORY
REC PAUSE/START
R06
3
R06
2R
061
Q10
2
R055
D113
R051
FB10
5
R178
R01
7
R041
R042
R043
FB104
R044
DIRECTION
DISC 3
DISC 2
DISC 1
ZOPEN/CLOSE
R04
5R
046
R047
R048
R04
9
R050
DISC SKIP/EX-CHANGE
R083
R084
R085
R086
JR101
R024
R078
R081
C119
R168
R10
7
R00
6C1
20 R080
R079
R197
R192
R19
5
C114
R170R171
R180R179
R184R185
R077
R194
C113
C144
R01
1
R17
2
R169
R004
R060
R05
7
R088
R087
R090
R089R
058
R00
8
R00
5
R01
0
R00
7
R01
2
R00
9
R182R183
R187
R174
R003
R116
R114
R19
3
R188
R19
8
R181
R127
R130
R10
8
R129
R123
R119R118
R122
R126
R121
R124R125
R128
C127
R013
R014R015
D102
C102FB101
FB102
C101
Q111
R096R095
IC103
C146
D10
7
D106
D105
R073R075
R07
4
R07
6
R07
2
D10
9
C145 D10
8
Q107
R111
R10
9 C112
R11
2
C110
C111
C125
R16
7 R131
R134R135
R136
R133
R142
R132
R143 R139
R141 R140
R138
R137R144R
145
R14
6R
147
R14
8
R14
9R
150
R15
1R
153
R15
4R
155
R15
7
R15
8
R15
6
R15
9R
160
R16
1
R16
3R
165
R16
6
R08
2
R177
C106
R04
0
R03
5
R03
6R
037
R03
8R
039
R02
5
R03
1
R03
2
R03
3
R034
R027R028
JR112
JR110
R152
JR120
R173D
111
D11
2
JR105
R059
R186
R016
C116
JR10
4
R162
R164
JR106
JR111
R110
R029 R030
R001
R00
2
D121
C129
C130
C153
JR119
C152
C154
JR12
1
C115
JR123
R17
5
NO
101
JW101
JW103
JW10
5
JW10
6
JW10
7
JW10
8
JW10
9
JW11
0
JW111
JW112
JW114
JW11
5
JW11
6
JW11
7JW11
8JW11
9
JW12
0
JW12
1
JW122
JW123
JW124
JW125
JW126
JW12
7
JW12
8
JW129
JW130
JW13
1
JW13
2
JW13
3
JW13
4
JW13
5JW
136
JW13
7
JW13
8JW
139
JW140
JW141JW142JW143JW144JW145JW146JW147JW148
JW149JW150
JW151
JW152JW153
JW154JW155
JW156JW157
JW158
JW159
JW16
1
JW16
2
JW16
3
JW16
4
JW16
5
JW16
6
JW16
7
JW16
8
JW16
9
JW170
JW17
2
JW173
JW174
JW175
JW176
JW178
JW179
JW180
JW181
JW182
JW183 JW18
4JW
185
JW18
9
JW19
1
JW19
2
JW19
3
JW194
JW19
5
JW19
6
JW19
7
JW19
8
JW19
9
JW20
0
JW20
1
JW203
JW204JW206
JW207JW208
JW211
JW21
2
JW21
3
JW21
4
JW21
5
JW21
6
JW21
7
JW21
8
JW21
9
JW22
0
JW221
JW222
JW223
JW224
JW225JW226
JW22
7
JW22
8
JW22
9
JW23
0
JW23
1
JW23
2
JW23
3
JW23
4
JW23
6
JW23
7
JW23
8
JW24
0
JW24
1
JW24
2
JW245
JW24
6
JW24
7
JW248
JW249
JW250
JW11
3
JW251
JW252
JW25
3
JW23
5
JW23
9
JW19
0
JW17
7
JW25
4
JW16
0
JW210
JW202
JW209
JW18
7
JW18
8
JW18
6
JW24
3
JW24
4
JW25
5
CN152LP101
X102
CN00
2
CN001
D110
C122
CN102
CN004
S35
S34
S33
S32
S57
S11
S31S12
S14
S56
S38
S51S52
SOUND FIELD
nN
S53
S54
S55
S15S16
S17
S18
S19
S20
C147
X101
C128
CN153
C126
CN00
3
CN005
FL101
CN151
C103
C121
C105
JW205
JW102
JW104
JW171
DVD
DISPLAY
MyTUNING+
m TUNING–
y
x
1
10
JR11
4
JR11
6
JR11
3
JR11
7
JR11
5
R069
NO151
NO152
S102
S101
D117D118
JR102 IC104
C148
IC104
CN143
3 1
(Page 32)
(Page 40)
(Page 34)
(Page 40)
51 51
HCD-GNZ5D
HCD-GNZ5D
7-24. PRINTED WIRING BOARD — JACK SECTION — • Refer to page 26 for Circuit Boards Location. : Uses unleaded solder.
1
A
B
C
D
E
F
G
2 3 4 5 6 7 8 9 10 11 12 13
G F
AUDIO BOARD CN203
AUDIO BOARD CN755
(CHASSIS)
1-865-693-
13
(14)
J1004PHONES
J1002MIC
2
5 4 6
1
7
3
1 2 3
RV1001MIC
LEVEL
(CHASSIS)
R1019
R1020
IC1001
R1009
R1010
R1006
R1008
R10
07
D1006
R10
14
R10
17
R1015
R10
11
R1012
C1036
C101
1
C101
6
C101
3
C100
6
C1008
D1005
R1013
FB10
04
FB10
03
JR1000
NO1001
JW1003
JW10
04
JW10
05
JW1006
JW10
07
JW10
08
JW10
09
JW10
10
JW1011JW
1012
LP1001NO1002
EP1001
JW10
13
EPT1001
C1005
EPT1002
C1014
C1010
C1007
C1009
C1012
R1032
R1031
J1004RV1001
JW10
02
1 41 4
(Page 40) (Page 40)
5252
HCD-GNZ5D
HCD-GNZ5D
7-25. SCHEMATIC DIAGRAM — JACK SECTION —
IC1001(2/2)
R1008
RV1001
R1012
R1007
C1013
C1010
IC1001(1/2)
R1014 C1011
R1015C1014
J1002
EP1001
C1005
FB1004FB1003
R1032R1031
J1004
JW1013
NO1002
C1007R1009
R1010
R1006
R1013C1008
C1006R1011
C1016 R1017
C1036D1005 D1006
C1012
C1009
EPT1002
EPT1001
JR1000
R1019R1020
NO1001
(Page 42)
(Page 41)
53 53
HCD-GNZ5D
HCD-GNZ5D
7-26. SCHEMATIC DIAGRAM — POWER SECTION —
C918
C912
C913
R914
R91
5
R91
6
C915
R919
CN901
D901
FH911 FH910
R901
L901
C903
C902
CN914
R911
CN915
FH926 FH925
FH928 FH927
FH920 FH919
FH918 FH917
NO912 NO903
JW924
Q902
JW921
JW923
EP901 EP904
EP902
JW901
S901
Q901
CN902
D912
D911
NO901
R904
RY901
JW910
F919
JW925
D913
F914
F915
F918
T911
NO911 NO902
F910
(Page 47)
(Page 43)
5454
HCD-GNZ5D
HCD-GNZ5D
7-27. PRINTED WIRING BOARD — TRANS SECTION — • Refer to page 26 for Circuit Boards Location. : Uses unleaded solder.
1
A
B
C
D
E
F
2 3 4 5 6 7 8 9 10 11 12 13 14
VSUB TRANS
BOARDNO902
1-866-975-
QFRONT AMP
BOARDNO471
WSUB TRANS BOARD NO903
LAUDIOBOARDNO701
11
(CHASSIS)
(11)
B C E
1 3
FH927
FH925
FH919
FH917 FH918
FH920
FH926
E12,E13 MODELE12,E13 MODEL
E12,E13 MODEL
NO9114P:E3,E15,PH MODEL2P:E12,E13MODEL
E3,E15,PH MODEL
FH928T911
POWERTRANSFORMER
1
567891011121314
2 3 4
JW923
1
2
3
4 JW92
1
JW920
C915
EP902
CN91
5
R915D91
3
R916
R91
4C913
D91
2
C912
D91
1
R911
F919
F918
F915
F914
C918
LP901
LP902
LP904
CN91
4
JW924
NO
911
R91
9
Q902
JW931JW932
JW93
3JW
934
NO912
JW92
5
(Page 55)(Page 46)
(Page 40)
(Page 55)
55 55
HCD-GNZ5D
HCD-GNZ5D
7-28. PRINTED WIRING BOARD — SUB TRANS SECTION — • Refer to page 26 for Circuit Boards Location. : Uses unleaded solder.
1
A
B
C
D
E
F
G
H
I
J
2 3 4 5 6 7 8 9 10
V
W
1TRANSBOARDNO912
POWERSWITCHING
ACIN
TRANS BOARD NO911
3
2 1
2 1
4 3 2 1
11
(CHASSIS)
(CHASSIS)
(11)
S901VOLTAGE SELECTOR
E12,E13 MODEL
E3,E15,PH MODEL
CN901
RY9
01
NO902
JW901
FH910FH911
F910
NO903
NO901
C903
C902
EP90
1EP
904
D90
1
Q90
1
R90
1
JW910
E12,E13 MODEL
E3,E15,PH MODEL
E12,E13 MODEL
LP903
L901
JW91
1
CN902
R90
4
JW902
1-866-976-
E
C
B
NO9024P:E3,E15,PH MODEL2P:E12,E13MODEL
(Page 54)
(Page 54)
5656
HCD-GNZ5D
HCD-GNZ5D
12
25 26 27 28 3129 30 34 35 3632 33
11 10 9 8 7 6 5 4 3
48
2 1
1447
46
45
44
43
42
41
40
39
38
37
13
15
16
17
21
18
22
23
24
1920
DATT
AUDIOINTERFACE
SDTI4
SDTI1
SDTI2
SDTI3
LRCK
I2CSCLSDA
CAD1
DCLK
DSDL
1DS
DR1
DSDL
1DS
DR2
DSDL
3DS
DR3
DIF0
ROUT
4-RO
UT4+
(DMIXR)
AVSS
VREF
HAV
DD
DSDL4
DSDR4
DAC
SCF
SCF
SCF
(FR)ROUT1+
DVSS
DVDD
MCL
K
BICK
PDN
ACKS
N
CAD0
DZF1
(SUR
)
DZF2
(R)
DZF3
(L)
LOUT
1+
LOUT
1+
ROUT1-
SCF
SCF
SCF
SCF
SCF
DATT DAC
DATT
CONTROLREGISTER
DAC
DATT DAC
DATT DAC
DATT DAC
DATT
DATT
DACDAC
(FL)
(SL)LOUT2+
LOUT2-
(SR)ROUT2+
ROUT2-
(FC)LOUT3+
LOUT3-
(SW)ROUT3+
ROUT3-
(DMIXL)LOUT4+
LOUT4-
1 2 3 4 5 6 7 8 9
CONTROL LOGIC
TSD
VREF
OUT2
OUT1
RNF
VM VCC
FIN
GND
RIN
IC301 AK4358VQ-L (DMB11 Board (1/4))
• IC BLOCK DIAGRAMS
IC701 BA6956AN (DRIVER Board)IC712 BA6956AN (DRIVER Board)
IC801 MM1671XNRE (VIDEO Board)
1
2
3 4
5
6
LPF
6.75MHz
6dB
PS
OUT
SAG
VCC
GND
IN
75ΩDRIVER
CLAMP
57
HCD-GNZ5D
• IC PIN DescriptionsIC101 M30392MEP-A10FPU0 (SYSTEM CONTROL) (PANEL BOARD (2/2))
Pin No. Pin Name I/O Pin Description
1 61537 CLK O TA device control serial clock signal output
2 61530 CLK O TA device control serial clock signal output
3 TA DATA O TA device control serial data signal output
4 STANDBY LED O Standby LED control signal output
5 VIDEO OUT SW O Video out switch control signal output “H”: VIDEO
6 VIDEO MUTE O Video mute signal output “L”: VIDEO
7 SIRCS I Remote control signal input
8 VACS2 I VACS signal input
9 CN VSS — Connector ground pin
10 X CIN I Sub clock signal input (32.768 kHz)
11 X COUT O Sub clock signal output (32.768 kHz)
12 RESET I Reset signal input
13 XOUT O Main clock signal output (16 MHz)
14 VSS — Ground pin
15 X IN I Main clock signal input (16 MHz)
16 VCC1 — Power supply pin (+3.3 V)
17 P85 I Pull up (EVER+3.3 V)
18 ILLUMI 1/4 O Illumination on/off control signal output “H”: On
19 ST TUNED I ST tuned signal input
20 AC CUT I AC cut signal input
21 ILLUMI CTRL O Illumination control signal output
22 DVD POWER O DVD power supply control signal output
23 MTK RESET O MTK reset signal output
24 MTK BUSY O MTK busy signal output
25 I2C CLK I/O I2C serial clock signal input/output
26 I2C DATA I/O I2C serial data signal input/output
27 MTK OUT O MTK serial data signal output
28 MTK IN I MTK serial data signal input
29 MTK CLK I MTK serial clock signal input
30 MTK CS I MTK chip select signal input
31 to 43 G13 to G1 O Grid and segment control signal output
44 to 51 P1 to P8 O Grid and segment control signal output
52 VEE — Power supply pin
53 to 61 P9 to P17 O Grid and segment control signal output
62 VCC2 — Power supply pin (+3.3 V)
63 P18 O Grid and segment control signal output
64 VSS — Ground pin
65 to 67 P19 to P21 O Grid and segment control signal output
68 ST CE O Tuner chip enable signal output
69 ST DIN I Tuner data in signal input
70 ST DOUT O Tuner data out signal output
71 ST CLK O Tuner serial clock signal output
72 I/O VCC CONT O In/out power supply control signal output
73 I/O LATCH O In/out serial latch control signal output
74 WAKE UP0 I Wake up signal input
75 I/O CLK O In/out serial clock control signal output
76 I/O DI1 O In/out serial data control signal output
77 I/O RST O In/out reset signal output
78 TRG (B) O Tape mechanism logic (Trigger B) control signal output
79 TRG (A) O Tape mechanism logic (Trigger A) control signal output
80 ILLUMI 3/6 O Illumination on/off control signal output “H”: On
81 ILLUMI 2/5 O Illumination on/off control signal output “H”: On
82PLAY SW (A) & (B)/
IHead up switch detect signal input (A deck and B deck)
A-HALF A deck HALF signal input
58
HCD-GNZ5D
Pin No. Pin Name I/O Pin Description
83 SHUT (A) I Protect detect signal input (A deck)
84 SHUT (B) I Protect detect signal input (B deck)
85 B HALF/REC I B deck HALF signal input/Record signal input (A deck and B deck)
86 BIAS O Bias on/off signal output
87KARAOKE/
IMTK KARAOKE mode signal input
MTK M REQ MTK mute request signal input
88 VACS/ILLUMI I VACS and illumination (L+R) control signal input
89VOL (A) & (B)/
IVolume A and B control signal input
SW IN Sub woofer control signal input
90 SPEC IN I Specification signal input
91 MODEL IN I Serial line up signal input
92 to 94 KEY2 to KEY0 I Key signal input
95CDM EJECT/
ICD mechanism eject detect signal input
PROTECT Protect detect signal input
96 AVSS — Ground pin
97 CDM ENC0/1/2 I CD mechanism switch signal input
98 VREF — Voltage reference pin
99 AVCC — Power supply pin (+3.3 V)
100 CDM TBL SENS I CD mechanism table sensor detect signal input
IC102 BH2210FV (SIGNAL IN/OUT CONTROL) (PANEL BOARD (2/2))
Pin No. Pin Name I/O Pin Description
1 CTLIO I IN/OUT control port (Fixed at “H” in this set.)
2 RSTB I Reset signal input
3 CLK I Serial clock signal input
4 LATCH I Serial latch signal input
5 STBY RELAY O Standby relay on/off signal output “H”: On, “L”: Off
6 FAN ON/OFF O Fan on/off signal output “H”: Off, “L”: On
7 FRONT RELAY O Front relay on/off signal output “H”: On, “L”: Off
8 TA MUTE O TA line mute on/off signal output “H”: Off, “L”: On
9 HP MUTE O Headphones mute on/off signal output “H”: Off, “L”: On
10 AU-OUT MUTE O Audio out mute on/off signal output “H”: Off, “L”: On
11 SW MUTE O Subwoofer mute on/off signal output “H”: Off, “L”: On
12 FAN CTRL O FAN control signal output “L”: Off
13 to 15 NO USE O Not used. (Open)
16 NO USE O Not used. (Fixed at “L”.)
17 TBL POS O CD mechanism table position control signal output
18 TBL NEG O CD mechanism table NEG control signal output
19 LOD POS O CD mechanism table loading position control signal output
20 LOD NEG O CD mechanism table NEG control signal output
21 PB/REC O Tape playback/record signal output “H”: REC, “L”: PB
22 REAR RELAY O Rear relay on/off signal output “H”: On, “L”: Off
23 SW RELAY O Subwoofer relay on/off signal output “H”: On, “L”: Off
24 CAPM SW O Capstan motor on/off signal output “H”: On, “L”: Off
25 DO2 O Not used. (Open)
26 DI1 I Serial data signal input
27 VSS — Ground pin
28 VDD — Power supply pin (+3 V)
59
HCD-GNZ5D
IC102 CXD9849R (DMB11 BOARD (3/4))(CD/DVD RF AMP, FOCUS/TRACKING ERR AMP, DVD SYSTEM PROCESSOR, DIGITAL SERVO PROCESSOR)
Pin No. Pin Name I/O Description
1 AGND — Terminal Ground
2 DVDA I AC coupled input path A
3 DVDB I AC coupled input path B
4 DVDC I AC coupled input path C
5 DVDD I AC coupled input path D
6 DVDRFIP I AC coupled DVD RF signal input RFIP
7 DVDRFIN I AC coupled DVD RF signal input RFIN (not used)
8 NA I DC coupled main-beam RF signal input A
9 NB I DC coupled main-beam RF signal input B
10 MC I DC coupled main-beam RF signal input C
11 MD I DC coupled main-beam RF signal input D
12 SA I DC coupled sub-beam RF signal input A (not used)
13 SB I DC coupled sub-beam RF signal input B (not used)
14 SC I DC coupled sub-beam RF signal input C (not used)
15 SD I DC coupled sub-beam RF signal input D (not used)
16 CDFON I CD focusing error negative input (not used)
17 CDFOP I CD focusing error positive input (not used)
18 TNI I 3 beam satellite PD signal negative input
19 TPI I 3 beam satellite PD signal positive input
20 MDI1 I Laser power PD monitor input
21 MDI2 I Laser power PD monitor input
22 LDO2 O Laser drive output
23 LDO1 O Laser drive output
24 SVDD3 — Power Supply (+3.3V)
25 CSO O Central servo, Positive main beam summing output (not used)
26 RFLVL O RFRP low pass, or Positive main beam summing output (not used)
27 SGND — Terminal Ground
28 V2REFO O Reference voltage 2.8V
29 V2O O Reference voltage 2.0V
30 VREFO O Reference voltage 1.4V
31 FEO O Focus error monitor output (not used)
32 TEO O Tracking error monitor output (not used)
33 TEZISLY O TE Slicing Level (not used)
34 OPOUT O Op amp output (not used)
35 OPIN I Op amp negative input (not used)
36 OPIN I Op amp positive input (not used)
37 DMO O Disk motor control output. PWM output
38 FMO O Feed motor control. PWM output
39 TROPENPWM O Tray PWM output/Tray open output.
40 IOPMON O General PWM output
41 TRO O Tracking servo output
42 FOO O Focus servo output
43 DVSS — Terminal Ground
44 NC — Not used. (Open)
45 NC — Not used. (Open)
46 DVDD3 — Power Supply (+3.3V)
47 SPFGG I Motor Hall sensor input
60
HCD-GNZ5D
Pin No. Pin Name I/O Description
48 DSEL O Select signal output
49 WIDE O SI signal output to VIDEO AMP
50 MSW O Volume control signal output to Optical pick-up
51 MAMUTE O MAMUTE signal output to System Controller (IC509) (not used)
52 DVDD18 — Power Supply (+1.8V)
53 to 58 IOA 2 to 7 O Address bus 2 to 7 output to PROM (IC101)
59 HIGHA0 O Address bus 8 output to PROM (IC101)
60, 61 IOA18, 19 O Address bus 18, 19 output to PROM (IC101)
62 DVSS — Terminal Ground
63 APLLCAP I APLL External Capacitance connection
64 APLLVSS — Terminal Ground
65 DVDD3 — Power Supply (+3.3V)
66 IOWA O WE signal output to PROM (IC101)
67 A16 O Address bus 16 output to PROM (IC101)
68 to 72 HIGHA 7 to 3 O Address bus 15 to 11 output to PROM (IC101)
73 DVDD3 — Power Supply (+3.3V)
74, 75 HIGHA 2, 1 O Address bus 10, 9 output to PROM (IC101)
76 IOA20 O Address bus 20 output to PROM (IC101)
77 IOCS O CE signal output to PROM (IC101)
78 IOA1 O Address bus 1 output to PROM (IC101)
79 IOOE O OE signal output to PROM (IC101)
80 DVDD3 — Power Supply (+3.3V)
81 to 84 AD 0 to 3 I Data bus 0 to 3 input from PROM (IC101)
85 DVSS — Terminal Ground
86 to 88 AD 4 to 6 I Data bus 4 to 6 input from PROM (IC101)
89 IOA21 O Address bus 21 output to PROM (IC101)
90 ALE O Address latch enable (not used)
91 AD7 I Data bus 7 input from PROM (IC101)
92 A17 O Address bus 17 output to PROM (IC101)
93 IOA0 O Address bus 0 output to PROM (IC101)
94 DVSS — Terminal Ground
95 UWA I System Controller write strobe (not used)
96 URB I System Controller read strobe (not used)
97 DVDD18 — Power Supply (+1.8V)
98 IFSDO I DVD SOD signal input from System Controller (IC509)
99 IFCK O DVD SCO signal output to System Controller (IC509)
100 XIFCS I DVD XIFCS signal input from System Controller (IC509)
101 IFSDI I VIFBUSY signal output from System Controller (IC509)
102 SCL O SCL signal output to EEPROM (IC103)
103 SDA O SDA signal output to EEPROM (IC103)
104 TRG-SW O RS232 RXD signal output (not used)
105 IF-BSY I RS232 TXD signal input from System Controller (IC509)
106 RXD I RD232 RXD clock
107 TXD I RD232 TXD data
108 DVDD3 — Power Supply (+3.3V)
109 ICE I ICE mode enable (not used)
110 PRST I MTRST signal input from System Controller (IC509)
111 IR I IR control signal input (not used)
112 INT0 I External interrupt0 (not used)
113 DQMO O DQM0 signal output to SD-RAM (IC104)
61
HCD-GNZ5D
Pin No. Pin Name I/O Description
114 MREQ I DQM signal input
115 RD7 I Data bus 7 from SD-RAM (IC104)
116 DVSS — Terminal Ground
117, 118 RD 6, 5 I Data bus 6, 5 from SD-RAM (IC104)
119 DVSS — Terminal Ground
120, 121 RD 4, 3 I Data bus 4, 3 from SD-RAM (IC104)
122 DVDD18 — Power Supply (+1.8V)
123 to 125 RD 2 to 0 I Data bus 2 to 0 from SD-RAM (IC104)
126 RD15 I Data bus 15 from SD-RAM (IC104)
127 DVDD3 — Power Supply (+3.3V)
128 RD 14 I Data bus 14 from SD-RAM (IC104)
129 to 133 RD 13 to 9 I Data bus 13 to 9 from SD-RAM (IC104)
134 DVSS — Terminal Ground
135 RD8 I Data bus 8 from SD-RAM (IC104)
136 GPI0 — Not used. (Open)
137 DQM1 O DQM1 signal output to SD-RAM (IC104)
138 REW O WE signal output to SD-RAM (IC104)
139 CAS O CAS signal output to SD-RAM (IC104)
140 RAS O RAS signal output to SD-RAM (IC104)
141 DVDD3 — Power Supply (+3.3V)
142 RCS O RCS signal output to SD-RAM (IC206)
143 BAO 0 BAO signal output to SD-RAM (IC206)
144 DVSS — Terminal Ground
145 BA1 O BA1 signal output to SD-RAM (IC104)
146 RA10 O Address bus 10 output to SD-RAM (IC104)
147 RA0 O Address bus 0 output to SD-RAM (IC104)
148 DVSS — Terminal Ground
149 to 151 RA 1 to 3 O Address bus 1 to 3 output to SD-RAM (IC104)
152 DVDD18 — Power Supply (+1.8V)
153 NC — Not used. (Open)
154 NC — Not used. (Open)
155 DVDD3 — Power Supply (+3.3V)
156 RCLK O CLK signal output to SD-RAM (IC104)
157 CKE O CKE signal output to SD-RAM (IC104)
158 to 160 RA 11 to 8 O Address bus 11 to 8 output to SD-RAM (IC104)
161 DVSS — Terminal Ground
162 RA7 O Address bus 7 output to SD-RAM (IC104)
163 DVSS — Terminal Ground
164 to 166 RA 6 to 4 O Address bus 6 to 4 output to SD-RAM (IC104)
167 DVDD3 — Power Supply (+3.3V)
168 DISC/X — Not used. (Open)
169 RGB O RGB control signal output Not used. (Open)
170 TSD M O TSDM signal output to Motor driver (IC201)
171 NC — Not used. (Open)
172 NC — Not used.
173 DVDD18 — Power Supply (+1.8V)
174 FWD O FWD signal output to Motor driver (IC201) Not used. (Open)
175 NC — Not used. (Open)
176 LIMSW O LIMSW signal output to Optical pick-up
62
HCD-GNZ5D
Pin No. Pin Name I/O Description
177 OCSW I SEN signal input from System Controller (IC509)/OCSW signal input
178 REW O REV signal output to Motor driver (IC201) Not used. (Open)
179 CKSW I CKSW signal input Not used. (Open)
180 NC — Not used. (Open)
181 NC — Not used. (Open)
182 DVDD3 — Power Supply (+3.3V)
183 NC — Not used. (Open)
184 NC — Not used. (Open)
185 NC — Not used. (Open)
186 NC — Not used. (Open)
187 NC — Not used. (Open)
188 NC — Not used. (Open)
189 DAVCC — Power Supply (+3.3V)
190 VREF I Bandgap reference voltage Not used. (Open)
191 FS O Full scale adjustment (pull down)
192 YUV0 — Not used. (Open)
193 DVSS — Terminal Ground
194 YUV1 O Y signal output to VIDEO AMP (IC201)
195 DAVDD — Power Supply (+3.3V)
196 YUV2 O CHROMA signal output to VIDEO AMP (IC201)
197 DVSS — Terminal Ground
198 YUV3 O VIDEO signal output to VIDEO AMP (IC201)
199 DAVDD — Power Supply (+3.3V)
200 YUV4 O G signal output to VIDEO AMP (IC201)
201 DVSS — Terminal Ground
202 YUV5 O B signal output to VIDEO AMP (IC201)
203 YUV6 O R signal output to VIDEO AMP (IC201)
204 DVDD3 — Power Supply (+3.3V)
205 MIC/VSYNC O MIC control signal output
206 VOICE/YUV7 — Not used.
207 KRMOB/HSYNC O KARAOKE mode control signal output
208 SMSCK — Not used. (Open)
209 SPDATA/SMSDI I Audio data of SPDIF input
210 MUTE O MUTE signal output to Motor driver (IC201)
211 MUTE123 O MUTE signal output to Motor driver (IC201)
212 DVDD3 — Power Supply (+3.3V)
213 ALRCK I Audio left/right channel clock
214 ABCK O Audio bit clock
215 ACLK I Audio DAC master clock
216 DVSS — Terminal Ground
217 ASDATA0 O Auio serial data
218 ASDATA1 O Auio serial data
219 ASDATA2 O Auio serial data
220 XRST O Reset signal output
221 DVDD18 — Power Supply (+1.8V)
222 ASDATA4 O Auio serial data (not used)
223 DVSS — Terminal Ground
224 DWIDE — Not used. (Open)
225 SDPIF — SPDIF output (not used)
226 RFGND18 — Terminal Ground
63
HCD-GNZ5D
Pin No. Pin Name I/O Description
227 RFVDD18 — Power Supply (+1.8V)
228 ZTALO O Oscillator output signal
229 ZTALI I Oscillator input signal
230 JITFO O RF jitter meter output
231 JITFN I Negative input of operation amplifier for RF jigger meter
232 PLLVSS — Terminal Ground
233 IDAC — Not used.
234 PLLVDD3 — Power Supply (+3.3V)
235 LPFON O Negative output of loop filter amplifier
236 LPFIP I Positive input of loop filter amplifier
237 LPFIN I Negative input of loop filter amplifier
238 LPFOP O Positive output of loop filter amplifier
239 VDD3 I Power Supply (+3.3V)
240 NC — Not used. (Open)
241 VSS — Terminal Ground
242 NC — Not used. (Open)
243 NC — Not used. (Open)
244 RFVDD3 — Power Supply (+3.3V)
245 RFRPDC I RFRP signal input
246 RFRPAC I RFRP signal input
247 HRFZC I High frequency RF ripple zero crossing
248 CRTPLP O Defect level filter capacitor connecting
249 RFGND — Terminal Ground
250 NC — Not used. (Open)
251 NC — Not used. (Open)
252 OSP O RF offset cancellation capacitor connecting
253 OSN I RF offset cancellation capacitor connecting
254 RFGC O RF offset loop capacitor connecting for DVD-ROM
255 IREF I Current reference input
256 AVDD3 — Power Supply (+3.3V)
64
HCD-GNZ5DSECTION 8
EXPLODED VIEWS
NOTE:• The mechanical parts with no reference
number in the exploded views are not supplied.• Items marked “*” are not stocked since
they are seldom required for routine service.Some delay should be anticipatedwhen ordering these items.
• -XX and -X mean standardized parts, sothey may have some difference from theoriginal one.
• Accessories are given in the last of thisparts list.
• AbbreviationE3 : 240 V AC area in E modelE12 : 220 – 240 V AC area in E modelE13 : 220 – 230 V AC area in E modelE15 : Iran modelPH : Philippine model
Ref. No. Part No. Description Remark
8-1. MAIN SECTION
Ref. No. Part No. Description Remark
1 2-582-718-31 ESCUTCHEON (LOADING)2 2-582-709-51 PANEL, LOADING3 3-363-099-02 SCREW (CASE 3 TP2)4 3-363-099-32 SCREW (CASE 3 TP2)5 4-245-183-71 CASE (SIDE-L)
6 4-244-849-71 CASE (TOP)
7 1-828-956-11 WIRE (FLAT TYPE) (9 CORE)8 4-245-184-71 CASE (SIDE-R)FAN901 1-763-072-11 FAN, DCTN1 1-693-671-11 TUNER (FM/AM) (TM-10E)#1 7-685-647-79 SCREW +BVTP 3X10 TYPE2 TT (B)
#2 7-685-871-01 SCREW +BVTT 3X6 (S)
The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.
#2
#2
#2
#1
#1 #2
#2
#2
#2
#1
#1
#1
#1
#2
FAN901
not supplied
not supplied(OPTICAL board)
front panelsection
chassis section
DVD block section
TN1
3
3
1
2
4
4
56
7
8
#1
65
HCD-GNZ5D
8-2. FRONT PANEL SECTION (1)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
51 A-1109-321-A JACK BOARD, COMPLETE52 3-087-053-01 +BVTP 2.6 (3CR)53 4-238-628-12 MIC KNOB54 A-1141-196-A PANEL BOARD, COMPLETE55 1-828-977-11 WIRE (FLAT TYPE) (13 CORE)
56 1-828-971-11 WIRE (FLAT TYPE) (13 CORE)57 1-829-041-11 WIRE (FLAT TYPE) (27 CORE)
58 1-797-246-11 DECK, MECHANISM59 1-828-332-11 WIRE (FLAT TYPE) (13 CORE)60 4-245-758-02 PLATE (HEAD), SHIELDFL101 1-519-811-11 INDICATOR TUBE, FLUORESCENT#2 7-685-871-01 SCREW +BVTT 3X6 (S)
#3 7-685-853-04 SCREW +BVTT 2X6 (S)
not supplied
not supplied
not supplied
not supplied
not supplied
FL101
not supplied(SIRCS board)
52
52
52
52 52
52
52
58
52
52
5456
57
51
53
5559
#2
#3
#3
52
60
66
HCD-GNZ5D
8-3. FRONT PANEL SECTION (2)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
101 4-231-836-01 SPRING (HEART CAM-A)102 4-231-824-01 CAM (A), HEART103 4-224-104-41 DAMPER104 2-582-708-01 LID (B), CASSETTE105 4-238-631-01 TAPE SPRING
106 2-582-720-01 ESCUTCHEON (LID TC)107 2-582-711-01 BUTTON (DISC)
108 2-582-707-01 LID (A), CASSETTE109 4-231-825-01 CAM (B), HEART110 4-231-841-01 SPRING (HEART CAM-B)111 X-2050-168-1 BUTTON (POWER) ASSY112 2-582-712-01 BUTTON (PLAY)
113 4-985-672-01 SCREW (+PTPWH M2.6), FLOATING
not supplied
not supplied
not supplied
101 102
103
105
103
104106
106
108
105
113
109
110
111112 112
107
67
HCD-GNZ5D
8-4. FRONT PANEL SECTION (3)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
151 2-582-706-12 PANEL, FRONT152 3-087-053-01 +BVTP 2.6 (3CR)153 4-233-980-01 RUBBER FOOT154 2-582-719-01 ESCUTCHEON (PANEL)155 2-582-715-01 RING (JOG)
156 2-582-714-01 INDICATOR (JOG)
157 2-590-671-12 KNOB (VOL)158 3-038-018-01 EMBLEM, SONY159 2-582-716-01 ESCUTCHEON (JOG)160 2-582-717-01 ORNAMENT (PLAY)161 2-582-719-21 ESCUTCHEON (PANEL)
162 2-582-721-02 WINDOW, INDICATION
not supplied
supplied with S102
not supplied
not supplied
not supplied
153
155
156154
157
159
151
152
152
160
161
162
158
not supplied(STREAM board)
68
HCD-GNZ5D
8-5. DVD BLOCK SECTION
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
201 A-1109-328-A VIDEO BOARD, COMPLETE202 1-828-354-11 WIRE (FLAT TYPE) (17 CORE)203 1-828-290-11 WIRE (FLAT TYPE) (5 CORE)204 A-1109-316-A DMB11 BOARD, COMPLETE (PH)
204 A-1109-317-A DMB11 BOARD, COMPLETE (EXCEPT PH)#2 7-685-871-01 SCREW +BVTT 3X6 (S)#4 7-685-646-79 SCREW +BVTP 3X8 TYPE2 TT (B)
#2
#4
#4
#4
#2
#2 #2
#2
not supplied
not supplied
not supplied
not suppliednot supplied
not supplied
not supplied
201202204
203
CDM74HF
69
HCD-GNZ5D
8-6. CHASSIS SECTION
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
251 4-233-980-01 RUBBER FOOT252 4-900-386-01 SCREW253 3-703-244-00 BUSHING (2104), CORD (E12,E13,PH)
* 253 3-703-571-12 BUSHING (S) (4516), CORD (E3,E15)0254 1-777-071-23 CORD, POWER (E12,E13,PH)
0254 1-827-226-31 CORD, POWER (E3,E15)0255 1-468-737-21 POWER, SWITCHING
256 3-970-608-01 SUMITITE (B3), +BV
0F910 1-532-504-33 FUSE (4A/250V) (E3,E15,PH)0F914 1-532-506-33 FUSE (6.3A/250V)0F915 1-532-506-33 FUSE (6.3A/250V)0F918 1-532-504-33 FUSE (4A/250V)0F919 1-532-504-33 FUSE (4A/250V)
0T911 1-443-792-11 TRANSFORMER, POWER#2 7-685-871-01 SCREW +BVTT 3X6 (S)
251
252
252
253
256
256
256256
254
255
F910
F914F915
F918
F919
T911
#2
#2
not supplied
not supplied
not supplied(TRANS board)
not supplied(SUB TRANS board)
70
HCD-GNZ5D
8-7. AUDIO BOARD SECTION
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
301 A-1109-313-A AUDIO BOARD, COMPLETE302 A-1109-314-A FRONT AMP BOARD, COMPLETEIC401 6-705-845-01 IC STK403-090IC941 8-759-198-03 IC PQ09RF21J00HIC942 8-759-701-59 IC NJM78M09FA
IC943 8-759-701-59 IC NJM78M09FAIC945 6-703-546-01 IC TA7804LS#4 7-685-646-79 SCREW +BVTP 3X8 TYPE2 TT (B)#5 7-685-650-79 SCREW +BVTP 3X16 TYPE2 IT-3
#5
#4
IC401
IC945
IC943IC942
IC941
not supplied
#4
#4
not supplied
not supplied(LEAD PIN board)
301
302
71
HCD-GNZ5D
8-8. DVD MECHANISM DECK SECTION (1)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
351 4-218-253-62 SCREW (M2.6), +BTTP352 1-776-182-11 WIRE (FLAT TYPE) (5 CORE)353 1-687-134-12 MOTOR (TB) BOARD354 4-243-815-11 TABLE (LOADING)355 4-245-571-02 GEAR (STOPPER)
356 4-218-252-61 SCREW (+PTPWH M2.6), FLOATING357 4-245-570-01 GEAR (JOINT)358 4-245-572-01 BUSHING (GEAR)359 1-687-132-12 SENSOR BOARD
360 4-243-820-01 GEAR (TABLE)361 4-243-819-01 GEAR (GENEVA)362 4-243-816-21 TRAY363 4-243-823-01 BELT (TABLE)364 4-985-672-01 SCREW (+PTPWH M2.6), FLOATING
365 4-243-821-01 PULLEY (TABLE)366 3-231-598-01 SHEET (BA)M741 A-1108-965-A MOTOR ASSY, TABLE (TABLE)
351
352
366
353
354
355355
356
356357
357
358
358359
351
356
362
363
364365360
361364
M741
chassis assy
72
HCD-GNZ5D
8-9. DVD MECHANISM DECK SECTION (2)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
401 A-1103-756-A DRIVER BOARD, COMPLETE402 4-218-253-52 SCREW (M2.6), +BTTP403 1-687-669-12 SW BOARD404 4-244-034-01 BELT (LOADING)405 4-985-672-01 SCREW (+PTPWH M2.6), FLOATING
406 4-225-844-01 GEAR (LOADING A)407 4-224-613-01 GEAR (SHAFT)408 1-687-133-12 MOTOR (LD) BOARD409 4-244-108-01 GEAR, SWING410 4-224-609-01 GEAR (LOADING C)
411 4-224-608-01 COLLAR, SWING412 3-016-533-11 WASHER (FR), STOPPER413 4-224-611-01 GEAR (LOADING B)
414 4-224-606-01 GEAR (RV)415 4-243-818-01 GEAR (U/D)416 2-541-918-01 LEVER (LIFTER (H))417 2-345-982-01 PULLEY A (310), CHUCKING418 2-345-983-01 PULLEY B (310), CHUCKING
419 3-087-599-01 INSULATOR SCREW420 2-634-618-01 INSULATOR421 1-828-771-51 WIRE (FLAT TYPE) (24 CORE)
0422 8-820-291-02 OPTICAL PICK-UP (KHM-310CAB/C2RP)423 4-251-923-01 YOKE (310)
M751 A-1108-966-A MOTOR ASSY, LOADING (LOADING)RE701 1-477-680-12 ENCODER, ROTARY (DISC TRAY ADDRESS
DETECT)
401
402
402
402
403
404
405
405406
407
408
409
410
411 412
413
414
415
416
418
419
419
420
420
420420
421
422
417
423
405
405
405
M751
not supplied not supplied
not supplied
not supplied
RE701
73
HCD-GNZ5DSECTION 9
ELECTRICAL PARTS LIST
NOTE:• Due to standardization, replacements in
the parts list may be different from theparts specified in the diagrams or thecomponents used on the set.
• -XX and -X mean standardized parts, sothey may have some difference from theoriginal one.
• RESISTORSAll resistors are in ohms.METAL:Metal-film resistor.METAL OXIDE: Metal oxide-film resistor.F:nonflammable
• Items marked “*” are not stocked sincethey are seldom required for routine service.Some delay should be anticipatedwhen ordering these items.
• SEMICONDUCTORSIn each case, u : µ, for example:uA.. : µA.. uPA.. : µPA..uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..
• CAPACITORSuF : µF
• COILSuH : µH
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.
When indicating parts by referencenumber, please include the board.
A-1109-313-A AUDIO BOARD, COMPLETE**********************
< CAPACITOR >
C201 1-164-156-11 CERAMIC CHIP 0.1uF 25VC202 1-104-658-11 ELECT 100uF 20% 10VC203 1-104-658-11 ELECT 100uF 20% 10VC204 1-104-658-11 ELECT 100uF 20% 10VC205 1-104-658-11 ELECT 100uF 20% 10V
C211 1-126-964-11 ELECT 10uF 20% 50VC213 1-126-964-11 ELECT 10uF 20% 50VC214 1-126-964-11 ELECT 10uF 20% 50VC218 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25VC219 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
C220 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16VC221 1-126-964-11 ELECT 10uF 20% 50VC222 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50VC223 1-126-964-11 ELECT 10uF 20% 50VC224 1-137-194-81 FILM 0.47uF 5% 50V
C225 1-137-194-81 FILM 0.47uF 5% 50VC226 1-126-960-11 ELECT 1uF 20% 50VC228 1-126-964-11 ELECT 10uF 20% 50VC236 1-130-491-00 MYLAR 0.047uF 5% 50VC237 1-126-964-11 ELECT 10uF 20% 50V
C239 1-126-959-11 ELECT 0.47uF 20% 50VC251 1-126-964-11 ELECT 10uF 20% 50VC253 1-126-964-11 ELECT 10uF 20% 50VC254 1-126-964-11 ELECT 10uF 20% 50VC256 1-126-964-11 ELECT 10uF 20% 50V
C258 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25VC259 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25VC260 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16VC261 1-126-964-11 ELECT 10uF 20% 50VC262 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C263 1-126-964-11 ELECT 10uF 20% 50VC264 1-137-194-81 FILM 0.47uF 5% 50VC265 1-137-194-81 FILM 0.47uF 5% 50VC266 1-126-960-11 ELECT 1uF 20% 50VC268 1-126-964-11 ELECT 10uF 20% 50V
C273 1-126-964-11 ELECT 10uF 20% 50VC274 1-126-960-11 ELECT 1uF 20% 50VC281 1-126-964-11 ELECT 10uF 20% 50VC282 1-104-658-11 ELECT 100uF 20% 10VC283 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C285 1-126-961-11 ELECT 2.2uF 20% 50VC286 1-104-658-11 ELECT 100uF 20% 10VC311 1-126-964-11 ELECT 10uF 20% 50VC312 1-126-964-11 ELECT 10uF 20% 50VC316 1-126-964-11 ELECT 10uF 20% 50V
C321 1-126-964-11 ELECT 10uF 20% 50VC322 1-126-964-11 ELECT 10uF 20% 50VC323 1-216-864-11 SHORT CHIP 0C325 1-126-964-11 ELECT 10uF 20% 50VC351 1-126-964-11 ELECT 10uF 20% 50V
C352 1-126-964-11 ELECT 10uF 20% 50VC356 1-126-964-11 ELECT 10uF 20% 50VC361 1-126-964-11 ELECT 10uF 20% 50VC362 1-126-964-11 ELECT 10uF 20% 50VC363 1-216-864-11 SHORT CHIP 0
C365 1-126-964-11 ELECT 10uF 20% 50VC367 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC368 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC601 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50VC602 1-164-245-11 CERAMIC CHIP 0.015uF 10% 25V
C603 1-136-155-00 FILM 0.015uF 5% 50VC604 1-126-965-11 ELECT 22uF 20% 50VC605 1-106-375-12 MYLAR 0.022uF 5% 200VC611 1-162-963-11 CERAMIC CHIP 680PF 10% 50VC612 1-100-670-11 CERAMIC CHIP 4.7uF 20% 16V
C613 1-162-963-11 CERAMIC CHIP 680PF 10% 50VC614 1-126-963-11 ELECT 4.7uF 20% 50VC615 1-137-150-11 FILM 0.01uF 5% 100VC616 1-126-947-11 ELECT 47uF 20% 35VC617 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C618 1-126-964-11 ELECT 10uF 20% 50VC619 1-136-497-81 FILM 0.1uF 5% 50VC620 1-126-960-11 ELECT 1uF 20% 50VC621 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC622 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C623 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC624 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC651 1-162-963-11 CERAMIC CHIP 680PF 10% 50VC652 1-100-670-11 CERAMIC CHIP 4.7uF 20% 16VC653 1-162-963-11 CERAMIC CHIP 680PF 10% 50V
C654 1-126-963-11 ELECT 4.7uF 20% 50VC655 1-137-150-11 FILM 0.01uF 5% 100VC656 1-126-947-11 ELECT 47uF 20% 35VC657 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50VC658 1-126-964-11 ELECT 10uF 20% 50V
• AbbreviationE3 : 240 V AC area in E modelE12 : 220 – 240 V AC area in E modelE13 : 220 – 230 V AC area in E modelE15 : Iran modelPH : Philippine model
AUDIO
74
HCD-GNZ5D
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C659 1-136-497-81 FILM 0.1uF 5% 50VC725 1-107-696-11 ELECT 47uF 20% 16VC726 1-107-696-11 ELECT 47uF 20% 16VC728 1-164-156-11 CERAMIC CHIP 0.1uF 25VC753 1-119-939-51 ELECT 6800uF 20% 35V
C763 1-111-235-61 ELECT 10000uF 20% 25VC764 1-126-963-11 ELECT 4.7uF 20% 50VC765 1-126-961-11 ELECT 2.2uF 20% 50VC771 1-126-956-11 ELECT 0.1uF 20% 50VC772 1-126-923-11 ELECT 220uF 20% 10V
C778 1-164-156-11 CERAMIC CHIP 0.1uF 25VC791 1-126-963-11 ELECT 4.7uF 20% 50VC793 1-162-974-11 CERAMIC CHIP 0.01uF 50VC794 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25VC795 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
< CONNECTOR >
CN201 1-573-847-11 CONNECTOR, BOARD TO BOARD 15PCN202 1-573-847-11 CONNECTOR, BOARD TO BOARD 15PCN203 1-785-316-11 PIN, CONNECTOR (STRAIGHT) 4PCN301 1-779-285-11 CONNECTOR, FFC (LIF(NON-ZIF)) 17PCN304 1-564-506-11 PLUG, CONNECTOR 3P
CN601 1-564-705-11 PIN, CONNECTOR (SMALL TYPE) 3P* CN602 1-564-710-11 PIN, CONNECTOR (SMALL TYPE) 8P
CN751 1-785-322-11 PIN, CONNECTOR (STRAIGHT) 10PCN752 1-784-788-11 CONNECTOR, FFC 27PCN753 1-568-828-11 CONNECTOR, FFC 9P
* CN754 1-564-518-11 PLUG, CONNECTOR 3PCN755 1-564-706-11 PIN, CONNECTOR (SMALL TYPE) 4P
< DIODE >
D201 6-501-193-01 DIODE 1SS355WTE-17D202 6-501-193-01 DIODE 1SS355WTE-17D235 6-501-193-01 DIODE 1SS355WTE-17D271 6-500-848-01 DIODE MC2840-T112-1D726 6-501-193-01 DIODE 1SS355WTE-17
D727 6-501-193-01 DIODE 1SS355WTE-17D728 6-501-193-01 DIODE 1SS355WTE-17D751 8-719-028-23 DIODE D3SBA20-4101D753 6-500-335-01 DIODE MC2838-T112-1D761 8-719-028-23 DIODE D3SBA20-4101
D762 6-501-193-01 DIODE 1SS355WTE-17D763 6-500-335-01 DIODE MC2838-T112-1D771 6-500-522-21 DIODE 10EDB40-TB3D791 6-501-193-01 DIODE 1SS355WTE-17D792 8-719-069-56 DIODE UDZSTE-176.2B
D793 8-719-069-56 DIODE UDZSTE-176.2B
< GROUND TERMINAL >
EPT751 1-537-771-21 TERMINAL BOARD, GROUND
< JUMPER RESISTOR >
FB301 1-216-295-11 SHORT CHIP 0
< IC >
IC201 6-705-667-01 IC M61537FP-RF0GIC203 6-703-610-01 IC RT8H015C-T112-1
IC771 6-703-547-01 IC TA7805LS
< JUMPER RESISTOR >
JR211 1-216-837-11 METAL CHIP 22K 5% 1/10WJR251 1-216-837-11 METAL CHIP 22K 5% 1/10WJR304 1-216-864-11 SHORT CHIP 0JR305 1-216-864-11 SHORT CHIP 0JW291 1-216-864-11 SHORT CHIP 0
JW293 1-216-864-11 SHORT CHIP 0
< COIL >
L302 1-408-619-31 INDUCTOR 220uH
< TRANSISTOR >
Q212 8-729-905-35 TRANSISTOR 2SC4081-RQ252 8-729-905-35 TRANSISTOR 2SC4081-RQ271 8-729-905-35 TRANSISTOR 2SC4081-RQ272 8-729-905-35 TRANSISTOR 2SC4081-RQ281 8-729-905-35 TRANSISTOR 2SC4081-R
Q282 8-729-905-35 TRANSISTOR 2SC4081-RQ283 8-729-905-35 TRANSISTOR 2SC4081-RQ601 8-729-011-92 TRANSISTOR 2SC2001TP-K1K2Q602 8-729-026-53 TRANSISTOR 2SA1576A-T106-QRQ603 8-729-905-35 TRANSISTOR 2SC4081-R
Q621 8-729-021-15 TRANSISTOR 2SD2351T106WQ622 8-729-021-15 TRANSISTOR 2SD2351T106WQ623 8-729-039-18 TRANSISTOR BCR183W-GEG-E6327Q624 8-729-039-14 TRANSISTOR BCR133W-GEG-E6327Q625 8-729-021-15 TRANSISTOR 2SD2351T106W
Q626 8-729-021-15 TRANSISTOR 2SD2351T106WQ627 8-729-021-15 TRANSISTOR 2SD2351T106WQ628 8-729-021-15 TRANSISTOR 2SD2351T106WQ629 8-729-026-53 TRANSISTOR 2SA1576A-T106-QRQ630 8-729-039-14 TRANSISTOR BCR133W-GEG-E6327
Q631 8-729-039-14 TRANSISTOR BCR133W-GEG-E6327Q701 8-729-021-15 TRANSISTOR 2SD2351T106WQ702 8-729-021-15 TRANSISTOR 2SD2351T106WQ703 8-729-021-15 TRANSISTOR 2SD2351T106WQ704 8-729-021-15 TRANSISTOR 2SD2351T106W
Q721 8-729-039-18 TRANSISTOR BCR183W-GEG-E6327Q722 8-729-039-14 TRANSISTOR BCR133W-GEG-E6327Q723 8-729-905-35 TRANSISTOR 2SC4081-RQ728 8-729-039-18 TRANSISTOR BCR183W-GEG-E6327Q729 8-729-039-18 TRANSISTOR BCR183W-GEG-E6327
Q771 6-550-185-01 TRANSISTOR RT1P137P-TP-1Q772 8-729-039-14 TRANSISTOR BCR133W-GEG-E6327Q791 8-729-039-14 TRANSISTOR BCR133W-GEG-E6327Q792 8-729-905-35 TRANSISTOR 2SC4081-RQ793 8-729-905-35 TRANSISTOR 2SC4081-R
Q794 8-729-026-68 TRANSISTOR 2SD2525(TP)Q795 8-729-039-14 TRANSISTOR BCR133W-GEG-E6327Q797 8-729-905-35 TRANSISTOR 2SC4081-R
< RESISTOR >
R201 1-216-821-11 METAL CHIP 1K 5% 1/10WR202 1-216-821-11 METAL CHIP 1K 5% 1/10WR211 1-216-864-11 SHORT CHIP 0
AUDIO
75
HCD-GNZ5D
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R212 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR213 1-216-833-11 METAL CHIP 10K 5% 1/10WR214 1-216-833-11 METAL CHIP 10K 5% 1/10WR215 1-216-821-11 METAL CHIP 1K 5% 1/10WR216 1-216-841-11 METAL CHIP 47K 5% 1/10W
R221 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR222 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
0R223 1-215-868-11 METAL OXIDE 680 5% 2W FR231 1-216-864-11 SHORT CHIP 0R232 1-216-833-11 METAL CHIP 10K 5% 1/10W
R235 1-216-837-11 METAL CHIP 22K 5% 1/10WR236 1-216-837-11 METAL CHIP 22K 5% 1/10WR237 1-216-833-11 METAL CHIP 10K 5% 1/10WR238 1-216-845-11 METAL CHIP 100K 5% 1/10WR239 1-216-857-11 METAL CHIP 1M 5% 1/10W
R251 1-216-864-11 SHORT CHIP 0R252 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR253 1-216-833-11 METAL CHIP 10K 5% 1/10WR254 1-216-833-11 METAL CHIP 10K 5% 1/10WR255 1-216-821-11 METAL CHIP 1K 5% 1/10W
R256 1-216-841-11 METAL CHIP 47K 5% 1/10WR261 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR262 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
0R263 1-215-868-11 METAL OXIDE 680 5% 2W FR271 1-216-821-11 METAL CHIP 1K 5% 1/10W
R272 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR273 1-216-837-11 METAL CHIP 22K 5% 1/10WR274 1-216-833-11 METAL CHIP 10K 5% 1/10WR275 1-216-845-11 METAL CHIP 100K 5% 1/10WR276 1-216-833-11 METAL CHIP 10K 5% 1/10W
R277 1-216-841-11 METAL CHIP 47K 5% 1/10WR282 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR311 1-216-864-11 SHORT CHIP 0R312 1-216-845-11 METAL CHIP 100K 5% 1/10WR313 1-216-864-11 SHORT CHIP 0
R315 1-216-864-11 SHORT CHIP 0R317 1-216-864-11 SHORT CHIP 0R321 1-216-864-11 SHORT CHIP 0R322 1-216-845-11 METAL CHIP 100K 5% 1/10WR323 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R351 1-216-864-11 SHORT CHIP 0R352 1-216-845-11 METAL CHIP 100K 5% 1/10WR353 1-216-864-11 SHORT CHIP 0R355 1-216-864-11 SHORT CHIP 0R357 1-216-864-11 SHORT CHIP 0
R361 1-216-864-11 SHORT CHIP 0R362 1-216-845-11 METAL CHIP 100K 5% 1/10WR363 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR601 1-216-838-11 METAL CHIP 27K 5% 1/10WR602 1-216-295-11 SHORT CHIP 0
R603 1-216-833-11 METAL CHIP 10K 5% 1/10WR604 1-216-833-11 METAL CHIP 10K 5% 1/10WR611 1-216-821-11 METAL CHIP 1K 5% 1/10WR612 1-216-821-11 METAL CHIP 1K 5% 1/10WR613 1-216-851-11 METAL CHIP 330K 5% 1/10W
R614 1-216-835-11 METAL CHIP 15K 5% 1/10WR615 1-216-812-11 METAL CHIP 180 5% 1/10WR616 1-216-834-11 METAL CHIP 12K 5% 1/10W
R617 1-216-835-11 METAL CHIP 15K 5% 1/10WR618 1-216-823-11 METAL CHIP 1.5K 5% 1/10WR620 1-216-857-11 METAL CHIP 1M 5% 1/10WR621 1-216-821-11 METAL CHIP 1K 5% 1/10WR622 1-216-821-11 METAL CHIP 1K 5% 1/10W
R623 1-216-821-11 METAL CHIP 1K 5% 1/10WR624 1-216-821-11 METAL CHIP 1K 5% 1/10WR625 1-216-821-11 METAL CHIP 1K 5% 1/10WR626 1-216-821-11 METAL CHIP 1K 5% 1/10WR627 1-216-833-11 METAL CHIP 10K 5% 1/10W
R628 1-216-833-11 METAL CHIP 10K 5% 1/10WR629 1-216-833-11 METAL CHIP 10K 5% 1/10WR632 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR639 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR651 1-216-821-11 METAL CHIP 1K 5% 1/10W
R652 1-216-821-11 METAL CHIP 1K 5% 1/10WR653 1-216-851-11 METAL CHIP 330K 5% 1/10WR654 1-216-835-11 METAL CHIP 15K 5% 1/10WR655 1-216-812-11 METAL CHIP 180 5% 1/10WR656 1-216-834-11 METAL CHIP 12K 5% 1/10W
R657 1-216-835-11 METAL CHIP 15K 5% 1/10WR658 1-216-823-11 METAL CHIP 1.5K 5% 1/10WR659 1-216-797-11 METAL CHIP 10 5% 1/10WR701 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR702 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R703 1-216-821-11 METAL CHIP 1K 5% 1/10WR704 1-216-821-11 METAL CHIP 1K 5% 1/10WR715 1-216-864-11 SHORT CHIP 0R717 1-216-864-11 SHORT CHIP 0R721 1-216-821-11 METAL CHIP 1K 5% 1/10W
R723 1-216-821-11 METAL CHIP 1K 5% 1/10WR737 1-216-833-11 METAL CHIP 10K 5% 1/10WR738 1-216-864-11 SHORT CHIP 0R739 1-216-841-11 METAL CHIP 47K 5% 1/10WR740 1-216-833-11 METAL CHIP 10K 5% 1/10W
R741 1-216-864-11 SHORT CHIP 0R742 1-216-841-11 METAL CHIP 47K 5% 1/10WR751 1-216-809-11 METAL CHIP 100 5% 1/10WR752 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR753 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R762 1-216-837-11 METAL CHIP 22K 5% 1/10WR763 1-216-837-11 METAL CHIP 22K 5% 1/10WR764 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10WR768 1-216-809-11 METAL CHIP 100 5% 1/10WR769 1-216-809-11 METAL CHIP 100 5% 1/10W
R790 1-216-809-11 METAL CHIP 100 5% 1/10WR791 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR792 1-216-841-11 METAL CHIP 47K 5% 1/10WR793 1-216-849-11 METAL CHIP 220K 5% 1/10WR794 1-216-837-11 METAL CHIP 22K 5% 1/10W
R795 1-216-837-11 METAL CHIP 22K 5% 1/10WR796 1-216-833-11 METAL CHIP 10K 5% 1/10WR798 1-216-809-11 METAL CHIP 100 5% 1/10W
< TRANSFORMER >
T601 1-437-220-11 TRANSFORMER, BIAS OSCILLATION*************************************************************
AUDIO
76
HCD-GNZ5D
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
A-1109-316-A DMB11 BOARD, COMPLETE (PH)A-1109-317-A DMB11 BOARD, COMPLETE (EXCEPT PH)
***********************
< CAPACITOR >
C101 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC102 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC105 1-126-205-11 ELECT CHIP 47uF 20% 6.3VC106 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC108 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C109 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC112 1-126-205-11 ELECT CHIP 47uF 20% 6.3VC113 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC114 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC115 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C116 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC117 1-124-779-00 ELECT CHIP 10uF 20% 16VC118 1-124-779-00 ELECT CHIP 10uF 20% 16VC119 1-124-779-00 ELECT CHIP 10uF 20% 16VC120 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C121 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC122 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC123 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC124 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC125 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C126 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC127 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC128 1-162-965-11 CERAMIC CHIP 0.0015uF 10% 50VC129 1-124-779-00 ELECT CHIP 10uF 20% 16VC130 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C131 1-125-838-11 CERAMIC CHIP 2.2uF 10% 6.3VC132 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC133 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC135 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16VC136 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C137 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC138 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC139 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC140 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC144 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C146 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC147 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16VC148 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16VC149 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC150 1-124-779-00 ELECT CHIP 10uF 20% 16V
C151 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25VC152 1-162-916-11 CERAMIC CHIP 12PF 5% 50VC153 1-162-916-11 CERAMIC CHIP 12PF 5% 50VC154 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC155 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C156 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC158 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC159 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC160 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC161 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C162 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC163 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC164 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C167 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC170 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC171 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC172 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC173 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C174 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC175 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC176 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC177 1-126-205-11 ELECT CHIP 47uF 20% 6.3VC178 1-126-208-21 ELECT CHIP 47uF 20% 4V
C179 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC180 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC181 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC182 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16VC184 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C187 1-126-208-21 ELECT CHIP 47uF 20% 4VC188 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16VC189 1-128-934-11 CERAMIC CHIP 0.33uF 20% 10VC190 1-126-205-11 ELECT CHIP 47uF 20% 6.3VC191 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C192 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC193 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16VC195 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16VC196 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50VC203 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C205 1-164-230-11 CERAMIC CHIP 220PF 5% 50VC206 1-164-230-11 CERAMIC CHIP 220PF 5% 50VC208 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC209 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16VC210 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C211 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16VC212 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC213 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC214 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC215 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C217 1-126-204-11 ELECT CHIP 47uF 20% 16VC218 1-124-779-00 ELECT CHIP 10uF 20% 16VC219 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC220 1-124-779-00 ELECT CHIP 10uF 20% 16VC221 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C222 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC224 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC233 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50VC301 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC302 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V
C305 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10VC306 1-126-206-11 ELECT CHIP 100uF 20% 6.3VC307 1-126-206-11 ELECT CHIP 100uF 20% 6.3VC402 1-126-204-11 ELECT CHIP 47uF 20% 16VC403 1-126-205-11 ELECT CHIP 47uF 20% 6.3V
C3701 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC3702 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC3707 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC3708 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC3711 1-162-977-11 CERAMIC CHIP 0.0018uF 10% 50V
C3712 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50VC3713 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC3714 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
DMB11Ver. 1.1
New part of EEP ROM (IC103) on the DMB11 board cannot be used. Therefore,if the mounted DMB11 board (A-1109-317-A, etc.) is replaced, exchange newEEP ROM (IC103) with that used before the replacement.
77
HCD-GNZ5D
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C3721 1-162-977-11 CERAMIC CHIP 0.0018uF 10% 50VC3722 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50VC3723 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC3724 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC3771 1-162-977-11 CERAMIC CHIP 0.0018uF 10% 50V
C3772 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50VC3773 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC3774 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC3781 1-162-977-11 CERAMIC CHIP 0.0018uF 10% 50VC3782 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50V
C3783 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC3784 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC3801 1-126-206-11 ELECT CHIP 100uF 20% 6.3VC3802 1-117-370-11 CERAMIC CHIP 10uF 10VC3803 1-126-205-11 ELECT CHIP 47uF 20% 6.3V
C3804 1-126-205-11 ELECT CHIP 47uF 20% 6.3VC3805 1-126-208-21 ELECT CHIP 47uF 20% 4V
< CONNECTOR >
CN101 1-815-763-32 CONNECTOR, FFC/FPC 24P* CN105 1-770-470-21 PIN, CONNECTOR (PC BOARD) 6P
CN106 1-793-989-21 CONNECTOR, FFC/FPC 13P* CN201 1-770-470-21 PIN, CONNECTOR (PC BOARD) 6P
CN301 1-784-365-21 CONNECTOR, FFC/FPC 5P
CN302 1-784-376-11 CONNECTOR, FFC/FPC 17PCN401 1-779-993-11 PIN, CONNECTOR (PWB) 5P
< DIODE >
D1001 8-719-058-24 DIODE RB501V-40TE-17D3501 6-501-193-01 DIODE 1SS355WTE-17D3502 6-501-193-01 DIODE 1SS355WTE-17
< FERRITE BEAD >
FB111 1-414-226-21 INDUCTOR, FERRITE BEADFB112 1-414-226-21 INDUCTOR, FERRITE BEADFB113 1-414-226-21 INDUCTOR, FERRITE BEADFB114 1-414-226-21 INDUCTOR, FERRITE BEADFB115 1-414-226-21 INDUCTOR, FERRITE BEAD
FB401 1-469-324-21 FERRITE, EMI (SMD) (2012)FB402 1-469-324-21 FERRITE, EMI (SMD) (2012)FB403 1-469-324-21 FERRITE, EMI (SMD) (2012)FB404 1-469-324-21 FERRITE, EMI (SMD) (2012)FB405 1-469-324-21 FERRITE, EMI (SMD) (2012)
FB406 1-469-324-21 FERRITE, EMI (SMD) (2012)
< FILTER >
FL101 1-234-177-21 FILTER, CHIP EMIFL104 1-234-177-21 FILTER, CHIP EMIFL105 1-234-177-21 FILTER, CHIP EMIFL106 1-234-177-21 FILTER, CHIP EMIFL107 1-234-177-21 FILTER, CHIP EMI
FL108 1-234-177-21 FILTER, CHIP EMIFL401 1-234-177-21 FILTER, CHIP EMIFL402 1-233-893-21 FILTER, CHIP EMIFL403 1-234-177-21 FILTER, CHIP EMI
< IC >
IC101 6-805-764-01 IC MX29LV320ABTC65-CBA4-0503CE(EXCEPT PH)
IC101 6-805-765-01 IC MX29LV320ABTC65-CBA4-0503GA (PH)IC102 6-707-535-01 IC CXD9849RIC103 (not supplied) IC BR24L64F-WE2IC104 6-705-929-01 IC K4S641632H-UC75T
IC105 6-702-302-01 IC TK11133CSCL-GIC106 6-708-153-01 IC PQ018EN01ZPHIC107 6-702-302-01 IC TK11133CSCL-GIC201 6-704-524-01 IC FAN8036LIC301 6-704-222-01 IC AK4358VQ-L
IC3711 8-759-359-49 IC NJM3414AV(TE2)IC3771 8-759-359-49 IC NJM3414AV(TE2)
< TRANSISTOR >
Q101 6-550-008-01 FET UM6K1N-TNQ102 6-550-653-01 FET QST8TRQ103 8-729-901-00 TRANSISTOR DTC124EKQ3801 8-729-230-49 TRANSISTOR 2SC2712-YG
< RESISTOR >
R101 1-216-809-11 METAL CHIP 100 5% 1/10WR104 1-216-864-11 SHORT CHIP 0R105 1-216-833-11 METAL CHIP 10K 5% 1/10WR106 1-216-833-11 METAL CHIP 10K 5% 1/10WR107 1-216-833-11 METAL CHIP 10K 5% 1/10W
R108 1-216-857-11 METAL CHIP 1M 5% 1/10WR109 1-216-864-11 SHORT CHIP 0R110 1-216-841-11 METAL CHIP 47K 5% 1/10WR111 1-216-809-11 METAL CHIP 100 5% 1/10WR112 1-211-977-11 METAL CHIP 22 0.5% 1/10W
R113 1-211-977-11 METAL CHIP 22 0.5% 1/10WR114 1-216-845-11 METAL CHIP 100K 5% 1/10WR115 1-211-977-11 METAL CHIP 22 0.5% 1/10WR116 1-216-821-11 METAL CHIP 1K 5% 1/10WR117 1-216-841-11 METAL CHIP 47K 5% 1/10W
R118 1-216-801-11 METAL CHIP 22 5% 1/10WR120 1-216-801-11 METAL CHIP 22 5% 1/10WR121 1-216-801-11 METAL CHIP 22 5% 1/10WR123 1-216-864-11 SHORT CHIP 0R124 1-216-841-11 METAL CHIP 47K 5% 1/10W
R126 1-216-864-11 SHORT CHIP 0R127 1-216-809-11 METAL CHIP 100 5% 1/10WR136 1-216-835-11 METAL CHIP 15K 5% 1/10WR138 1-216-845-11 METAL CHIP 100K 5% 1/10WR141 1-218-916-11 METAL CHIP 750K 0.5% 1/10W
R142 1-216-845-11 METAL CHIP 100K 5% 1/10WR143 1-469-116-21 FERRITE, EMI (SMD) (1608)R144 1-216-864-11 SHORT CHIP 0R146 1-216-805-11 METAL CHIP 47 5% 1/10WR151 1-216-805-11 METAL CHIP 47 5% 1/10W
R152 1-216-864-11 SHORT CHIP 0R153 1-216-805-11 METAL CHIP 47 5% 1/10WR155 1-216-805-11 METAL CHIP 47 5% 1/10WR160 1-216-805-11 METAL CHIP 47 5% 1/10WR161 1-216-809-11 METAL CHIP 100 5% 1/10W
DMB11Ver. 1.1
New part of EEP ROM (IC103) on the DMB11 board cannot be used. Therefore,if the mounted DMB11 board (A-1109-317-A, etc.) is replaced, exchange newEEP ROM (IC103) with that used before the replacement.
78
HCD-GNZ5D
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R164 1-216-809-11 METAL CHIP 100 5% 1/10WR169 1-216-833-11 METAL CHIP 10K 5% 1/10WR187 1-216-864-11 SHORT CHIP 0R189 1-218-827-11 METAL CHIP 150 0.5% 1/10WR190 1-218-827-11 METAL CHIP 150 0.5% 1/10W
R191 1-216-821-11 METAL CHIP 1K 5% 1/10WR192 1-218-827-11 METAL CHIP 150 0.5% 1/10WR193 1-216-821-11 METAL CHIP 1K 5% 1/10WR195 1-218-827-11 METAL CHIP 150 0.5% 1/10WR196 1-216-864-11 SHORT CHIP 0
R197 1-218-827-11 METAL CHIP 150 0.5% 1/10WR204 1-216-822-11 METAL CHIP 1.2K 5% 1/10WR205 1-216-833-11 METAL CHIP 10K 5% 1/10WR206 1-216-833-11 METAL CHIP 10K 5% 1/10WR207 1-216-826-11 METAL CHIP 2.7K 5% 1/10W
R208 1-216-839-11 METAL CHIP 33K 5% 1/10WR209 1-216-839-11 METAL CHIP 33K 5% 1/10WR210 1-216-841-11 METAL CHIP 47K 5% 1/10WR212 1-216-833-11 METAL CHIP 10K 5% 1/10WR213 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W
R214 1-216-835-11 METAL CHIP 15K 5% 1/10WR215 1-216-834-11 METAL CHIP 12K 5% 1/10WR216 1-216-834-11 METAL CHIP 12K 5% 1/10WR219 1-216-838-11 METAL CHIP 27K 5% 1/10WR220 1-216-833-11 METAL CHIP 10K 5% 1/10W
R221 1-218-889-11 METAL CHIP 56K 0.5% 1/10WR223 1-218-895-11 METAL CHIP 100K 0.5% 1/10WR224 1-216-833-11 METAL CHIP 10K 5% 1/10WR225 1-218-895-11 METAL CHIP 100K 0.5% 1/10WR226 1-218-889-11 METAL CHIP 56K 0.5% 1/10W
R230 1-218-893-11 METAL CHIP 82K 0.5% 1/10WR231 1-218-875-11 METAL CHIP 15K 0.5% 1/10WR232 1-218-877-11 METAL CHIP 18K 0.5% 1/10WR233 1-218-883-11 METAL CHIP 33K 0.5% 1/10WR234 1-216-833-11 METAL CHIP 10K 5% 1/10W
R246 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR247 1-216-821-11 METAL CHIP 1K 5% 1/10WR314 1-216-809-11 METAL CHIP 100 5% 1/10WR318 1-216-864-11 SHORT CHIP 0R319 1-216-864-11 SHORT CHIP 0
R321 1-216-864-11 SHORT CHIP 0R1101 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR1102 1-218-827-11 METAL CHIP 150 0.5% 1/10WR1103 1-216-833-11 METAL CHIP 10K 5% 1/10WR1104 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1105 1-216-833-11 METAL CHIP 10K 5% 1/10WR1108 1-216-864-11 SHORT CHIP 0R1109 1-216-864-11 SHORT CHIP 0R1110 1-216-826-11 METAL CHIP 2.7K 5% 1/10WR1123 1-216-864-11 SHORT CHIP 0
R1126 1-216-833-11 METAL CHIP 10K 5% 1/10WR1129 1-216-845-11 METAL CHIP 100K 5% 1/10WR1133 1-216-864-11 SHORT CHIP 0R1134 1-216-864-11 SHORT CHIP 0R1150 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R1151 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR1152 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR1168 1-216-817-11 METAL CHIP 470 5% 1/10W
R1502 1-216-864-11 SHORT CHIP 0R1504 1-216-864-11 SHORT CHIP 0R1524 1-216-864-11 SHORT CHIP 0R1526 1-216-864-11 SHORT CHIP 0R1530 1-216-864-11 SHORT CHIP 0
R1531 1-216-864-11 SHORT CHIP 0R1540 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR1542 1-216-833-11 METAL CHIP 10K 5% 1/10WR1543 1-216-833-11 METAL CHIP 10K 5% 1/10WR1544 1-216-864-11 SHORT CHIP 0
R1546 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR1547 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR1548 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR1549 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR1550 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R1551 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR1552 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR1553 1-216-864-11 SHORT CHIP 0R1554 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR1557 1-216-809-11 METAL CHIP 100 5% 1/10W
R2504 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR3501 1-216-809-11 METAL CHIP 100 5% 1/10WR3652 1-216-864-11 SHORT CHIP 0R3653 1-216-864-11 SHORT CHIP 0R3711 1-218-271-11 METAL CHIP 2K 5% 1/10W
R3712 1-218-271-11 METAL CHIP 2K 5% 1/10WR3713 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR3714 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR3715 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR3716 1-216-821-11 METAL CHIP 1K 5% 1/10W
R3717 1-216-821-11 METAL CHIP 1K 5% 1/10WR3718 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR3719 1-216-821-11 METAL CHIP 1K 5% 1/10WR3721 1-218-271-11 METAL CHIP 2K 5% 1/10WR3722 1-218-271-11 METAL CHIP 2K 5% 1/10W
R3723 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR3724 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR3725 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR3726 1-216-821-11 METAL CHIP 1K 5% 1/10WR3727 1-216-821-11 METAL CHIP 1K 5% 1/10W
R3728 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR3729 1-216-821-11 METAL CHIP 1K 5% 1/10WR3771 1-218-271-11 METAL CHIP 2K 5% 1/10WR3772 1-218-271-11 METAL CHIP 2K 5% 1/10WR3773 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R3774 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR3775 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR3776 1-216-821-11 METAL CHIP 1K 5% 1/10WR3777 1-216-821-11 METAL CHIP 1K 5% 1/10WR3778 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R3779 1-216-821-11 METAL CHIP 1K 5% 1/10WR3781 1-218-271-11 METAL CHIP 2K 5% 1/10WR3782 1-218-271-11 METAL CHIP 2K 5% 1/10WR3783 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR3784 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R3785 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR3786 1-216-821-11 METAL CHIP 1K 5% 1/10WR3787 1-216-821-11 METAL CHIP 1K 5% 1/10W
DMB11
79
HCD-GNZ5D
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R3788 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR3789 1-216-821-11 METAL CHIP 1K 5% 1/10WR3801 1-216-864-11 SHORT CHIP 0R3802 1-216-864-11 SHORT CHIP 0R3803 1-216-833-11 METAL CHIP 10K 5% 1/10W
R3804 1-216-836-11 METAL CHIP 18K 5% 1/10WR3805 1-216-821-11 METAL CHIP 1K 5% 1/10WR4701 1-216-864-11 SHORT CHIP 0R4702 1-216-864-11 SHORT CHIP 0R4703 1-216-864-11 SHORT CHIP 0
R4704 1-216-864-11 SHORT CHIP 0R4705 1-216-864-11 SHORT CHIP 0R4706 1-216-864-11 SHORT CHIP 0R5005 1-216-864-11 SHORT CHIP 0R5011 1-216-864-11 SHORT CHIP 0
R5016 1-216-864-11 SHORT CHIP 0 (EXCEPT PH)R5017 1-216-864-11 SHORT CHIP 0 (PH)
< NETWORK RESISTOR >
RB103 1-234-795-21 RES, NETWORK 0X4 (2010)RB104 1-234-795-21 RES, NETWORK 0X4 (2010)RB105 1-234-371-21 RES, NETWORK 47X4 (1005)RB106 1-234-371-21 RES, NETWORK 47X4 (1005)RB107 1-234-370-21 RES, NETWORK 22X4 (1005)
RB108 1-234-370-21 RES, NETWORK 22X4 (1005)RB111 1-234-795-21 RES, NETWORK 0X4 (2010)RB112 1-234-370-21 RES, NETWORK 22X4 (1005)RB113 1-234-370-21 RES, NETWORK 22X4 (1005)
< VIBRATOR >
X101 1-781-867-21 VIBRATOR, CRYSTAL (27MHz)*************************************************************
A-1103-756-A DRIVER BOARD, COMPLETE***********************
< CAPACITOR >
C715 1-126-933-11 ELECT 100uF 20% 16VC731 1-126-964-11 ELECT 10uF 20% 50VC735 1-164-159-21 CERAMIC 0.1uF 50VC736 1-164-159-21 CERAMIC 0.1uF 50VC737 1-164-159-21 CERAMIC 0.1uF 50V
C741 1-162-306-11 CERAMIC 0.01uF 20% 16VC751 1-162-306-11 CERAMIC 0.01uF 20% 16VC752 1-164-159-21 CERAMIC 0.1uF 50V
< CONNECTOR >
CN701 1-784-735-11 CONNECTOR, FFC 13PCN702 1-784-766-11 CONNECTOR, FFC 5P
* CN703 1-564-720-11 PIN, CONNECTOR (SMALL TYPE) 4PCN704 1-785-328-11 PIN, CONNECTOR (LIGHT ANGLE) 2P
< DIODE >
D701 8-719-921-42 DIODE MTZJ-5.1AD711 8-719-109-69 DIODE RD3.6ESB2
< IC >
IC701 8-759-598-69 IC BA6956AN
IC712 8-759-598-69 IC BA6956AN
< TRANSISTOR >
Q731 8-729-029-66 TRANSISTOR DTC114ESA
< RESISTOR >
R701 1-249-413-11 CARBON 470 5% 1/4WR702 1-247-807-31 CARBON 100 5% 1/4WR711 1-249-417-11 CARBON 1K 5% 1/4WR712 1-249-425-11 CARBON 4.7K 5% 1/4WR713 1-249-433-11 CARBON 22K 5% 1/4W
R721 1-249-425-11 CARBON 4.7K 5% 1/4WR722 1-249-425-11 CARBON 4.7K 5% 1/4WR723 1-249-425-11 CARBON 4.7K 5% 1/4WR731 1-247-807-31 CARBON 100 5% 1/4WR732 1-249-429-11 CARBON 10K 5% 1/4W
R733 1-249-417-11 CARBON 1K 5% 1/4WR734 1-249-430-11 CARBON 12K 5% 1/4WR735 1-247-807-31 CARBON 100 5% 1/4WR751 1-249-425-11 CARBON 4.7K 5% 1/4W
*************************************************************
A-1109-314-A FRONT AMP BOARD, COMPLETE***************************
7-685-872-09 SCREW +BVTT 3X8 (S)
< CAPACITOR >
C401 1-126-964-11 ELECT 10uF 20% 50VC402 1-162-302-11 CERAMIC 0.0022uF 20% 16VC403 1-162-286-31 CERAMIC 220PF 10% 50VC404 1-126-967-11 ELECT 47uF 20% 50VC406 1-136-495-11 FILM 0.068uF 5% 50V
C407 1-136-495-11 FILM 0.068uF 5% 50VC408 1-126-968-11 ELECT 100uF 20% 50VC410 1-126-926-11 ELECT 1000uF 20% 10VC416 1-162-306-11 CERAMIC 0.01uF 20% 16VC421 1-128-575-11 ELECT 33uF 20% 63V
C451 1-126-964-11 ELECT 10uF 20% 50VC452 1-162-302-11 CERAMIC 0.0022uF 20% 16VC453 1-162-286-31 CERAMIC 220PF 10% 50VC454 1-126-967-11 ELECT 47uF 20% 50VC456 1-136-495-11 FILM 0.068uF 5% 50V
C457 1-136-495-11 FILM 0.068uF 5% 50VC458 1-126-968-11 ELECT 100uF 20% 50VC471 1-135-832-11 ELECT 2200uF 20% 50VC472 1-135-832-11 ELECT 2200uF 20% 50VC485 1-162-306-11 CERAMIC 0.01uF 20% 16V
C486 1-162-306-11 CERAMIC 0.01uF 20% 16VC941 1-126-956-11 ELECT 0.1uF 20% 50VC942 1-126-925-11 ELECT 470uF 20% 10VC943 1-126-956-11 ELECT 0.1uF 20% 50VC944 1-104-658-11 ELECT 100uF 20% 10V
C945 1-126-956-11 ELECT 0.1uF 20% 50VC946 1-104-658-11 ELECT 100uF 20% 10VC949 1-126-947-11 ELECT 47uF 20% 35VC950 1-104-658-11 ELECT 100uF 20% 10V
DMB11 DRIVER FRONT AMP
80
HCD-GNZ5D
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
< CONNECTOR >
CN401 1-573-829-11 CONNECTOR, BOARD TO BOARD 15PCN402 1-573-829-11 CONNECTOR, BOARD TO BOARD 15P
< DIODE >
D401 8-719-991-33 DIODE 1SS133T-77D410 8-719-210-21 DIODE 11EQS04D451 8-719-991-33 DIODE 1SS133T-77D471 8-719-510-68 DIODE D5SBA204101D481 8-719-991-33 DIODE 1SS133T-77
D485 8-719-991-33 DIODE 1SS133T-77D486 8-719-991-33 DIODE 1SS133T-77D491 8-719-991-33 DIODE 1SS133T-77
< IC >
IC401 6-705-845-01 IC STK403-090
< TRANSISTOR >
Q401 8-729-140-84 TRANSISTOR 2SC1841-PAFAEAQ402 8-729-140-82 TRANSISTOR 2SA988-PAFAEAQ403 8-729-140-84 TRANSISTOR 2SC1841-PAFAEAQ416 8-729-119-78 TRANSISTOR 2SC2785-HFEQ417 8-729-119-78 TRANSISTOR 2SC2785-HFE
Q451 8-729-140-84 TRANSISTOR 2SC1841-PAFAEAQ481 8-729-140-82 TRANSISTOR 2SA988-PAFAEAQ482 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA
< RESISTOR >
R401 1-247-831-11 CARBON 1K 5% 1/4WR402 1-247-871-11 CARBON 47K 5% 1/4WR403 1-247-812-11 CARBON 160 5% 1/4WR404 1-247-871-11 CARBON 47K 5% 1/4W
0R406 1-208-602-11 METAL 0.22X2 2W
R407 1-247-831-11 CARBON 1K 5% 1/4WR408 1-249-431-11 CARBON 15K 5% 1/4WR409 1-247-879-11 CARBON 100K 5% 1/4WR410 1-260-076-11 CARBON 10 5% 1/2W F
0R411 1-212-881-11 FUSIBLE 100 5% 1/4W F
R412 1-247-887-00 CARBON 220K 5% 1/4WR413 1-249-421-11 CARBON 2.2K 5% 1/4WR415 1-249-429-11 CARBON 10K 5% 1/4WR416 1-249-429-11 CARBON 10K 5% 1/4WR417 1-249-429-11 CARBON 10K 5% 1/4W
R418 1-247-871-11 CARBON 47K 5% 1/4W0R419 1-202-972-61 FUSIBLE 1 5% 1/4W F0R420 1-202-972-61 FUSIBLE 1 5% 1/4W F
R421 1-249-429-11 CARBON 10K 5% 1/4WR425 1-249-439-11 CARBON 68K 5% 1/4W
R426 1-249-426-11 CARBON 5.6K 5% 1/4WR427 1-249-421-11 CARBON 2.2K 5% 1/4WR428 1-247-863-11 CARBON 22K 5% 1/4WR429 1-249-429-11 CARBON 10K 5% 1/4WR430 1-249-429-11 CARBON 10K 5% 1/4W
R439 1-247-871-11 CARBON 47K 5% 1/4WR440 1-247-873-11 CARBON 56K 5% 1/4WR451 1-247-831-11 CARBON 1K 5% 1/4WR452 1-247-871-11 CARBON 47K 5% 1/4W
R453 1-247-812-11 CARBON 160 5% 1/4WR454 1-247-871-11 CARBON 47K 5% 1/4W
0R456 1-208-602-11 METAL 0.22X2 2WR457 1-247-831-11 CARBON 1K 5% 1/4WR458 1-249-431-11 CARBON 15K 5% 1/4W
R459 1-247-879-11 CARBON 100K 5% 1/4WR460 1-260-076-11 CARBON 10 5% 1/2W F
0R461 1-212-881-11 FUSIBLE 100 5% 1/4W FR471 1-247-879-11 CARBON 100K 5% 1/4WR472 1-247-879-11 CARBON 100K 5% 1/4W
0R480 1-215-890-11 METAL OXIDE 470 5% 2W FR485 1-247-871-11 CARBON 47K 5% 1/4WR486 1-247-871-11 CARBON 47K 5% 1/4WR487 1-249-429-11 CARBON 10K 5% 1/4WR488 1-247-871-11 CARBON 47K 5% 1/4W
R489 1-249-429-11 CARBON 10K 5% 1/4WR490 1-249-429-11 CARBON 10K 5% 1/4WR941 1-247-831-11 CARBON 1K 5% 1/4W
< RELAY >
RY481 1-515-920-11 RELAY (24V)
< THERMISTOR >
TH401 1-807-796-11 THERMISTOR
< TERMINAL BOARD >
TM401 1-694-677-12 TERMINAL BOARD (4P) (FRONT SPEAKER)*************************************************************
A-1109-321-A JACK BOARD, COMPLETE*********************
< CAPACITOR >
C1005 1-115-872-11 ELECT 2.2uF 20% 50VC1006 1-162-955-11 CERAMIC CHIP 150PF 5% 50VC1007 1-126-786-11 ELECT 47uF 20% 16VC1008 1-162-949-11 CERAMIC CHIP 47PF 5% 50VC1009 1-115-872-11 ELECT 2.2uF 20% 50V
C1010 1-115-867-11 ELECT 0.1uF 20% 50VC1011 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC1012 1-126-786-11 ELECT 47uF 20% 16VC1013 1-162-949-11 CERAMIC CHIP 47PF 5% 50VC1014 1-115-868-11 ELECT 0.22uF 20% 50V
C1016 1-107-726-11 CERAMIC CHIP 0.01uF 10% 16VC1036 1-164-360-11 CERAMIC CHIP 0.1uF 16V
< DIODE >
D1005 6-501-193-01 DIODE 1SS355WTE-17D1006 6-501-193-01 DIODE 1SS355WTE-17
< GROUND TERMINAL >
EPT1001 1-537-771-21 TERMINAL BOARD, GROUNDEPT1002 1-537-771-21 TERMINAL BOARD, GROUND
< JUMPER RESISTOR >
FB1003 1-216-295-11 SHORT CHIP 0FB1004 1-216-295-11 SHORT CHIP 0
FRONT AMP JACK
81
HCD-GNZ5D
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
< IC >
IC1001 8-759-710-97 IC NJM4565M-D
< JACK >
J1002 1-770-226-11 JACK (LARGE TYPE) (MIC)J1004 1-794-702-11 JACK, HEADPHONE (PHONES)
< JUMPER RESISTOR >
JR1000 1-216-295-11 SHORT CHIP 0
< RESISTOR >
R1006 1-216-845-11 METAL CHIP 100K 5% 1/10WR1007 1-216-813-11 METAL CHIP 220 5% 1/10WR1008 1-216-809-11 METAL CHIP 100 5% 1/10WR1009 1-216-830-11 METAL CHIP 5.6K 5% 1/10WR1010 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R1011 1-216-847-11 METAL CHIP 150K 5% 1/10WR1012 1-216-833-11 METAL CHIP 10K 5% 1/10WR1013 1-216-809-11 METAL CHIP 100 5% 1/10WR1014 1-216-851-11 METAL CHIP 330K 5% 1/10WR1015 1-216-835-11 METAL CHIP 15K 5% 1/10W
R1017 1-216-833-11 METAL CHIP 10K 5% 1/10WR1019 1-216-864-11 SHORT CHIP 0R1020 1-216-864-11 SHORT CHIP 0R1031 1-260-083-11 CARBON 47 5% 1/2WR1032 1-260-083-11 CARBON 47 5% 1/2W
< VARIABLE RESISTOR >
RV1001 1-223-983-11 RES, VAR, CARBON 50K (MIC LEVEL)*************************************************************
1-687-133-12 MOTOR (LD) BOARD*****************
*************************************************************
1-687-134-12 MOTOR (TB) BOARD*****************
< CONNECTOR >
CN742 1-784-727-11 CONNECTOR, FFC 5P*************************************************************
OPTICAL BOARD**************
< CAPACITOR >
C308 1-164-156-11 CERAMIC CHIP 0.1uF 25VC309 1-126-923-11 ELECT 220uF 20% 10V
< IC >
IC306 6-600-465-11 IC TOTX147 (DIGITAL OUT OPTICAL)
< JUMPER RESISTOR >
R304 1-216-864-11 SHORT CHIP 0*************************************************************
A-1141-196-A PANEL BOARD, COMPLETE**********************
< CAPACITOR >
C101 1-164-156-11 CERAMIC CHIP 0.1uF 25VC102 1-164-156-11 CERAMIC CHIP 0.1uF 25VC103 1-126-916-11 ELECT 1000uF 20% 6.3VC104 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC105 1-119-941-11 ELECT 470uF 20% 6.3V
C106 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC110 1-162-918-11 CERAMIC CHIP 18PF 5% 50VC111 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC112 1-164-156-11 CERAMIC CHIP 0.1uF 25VC113 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C114 1-162-974-11 CERAMIC CHIP 0.01uF 50VC115 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3VC116 1-162-953-11 CERAMIC CHIP 100PF 5% 50VC117 1-162-953-11 CERAMIC CHIP 100PF 5% 50VC118 1-162-953-11 CERAMIC CHIP 100PF 5% 50V
C119 1-162-953-11 CERAMIC CHIP 100PF 5% 50VC120 1-162-953-11 CERAMIC CHIP 100PF 5% 50VC121 1-119-941-11 ELECT 470uF 20% 6.3VC122 1-119-941-11 ELECT 470uF 20% 6.3VC125 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C126 1-119-943-11 ELECT 47uF 20% 50VC127 1-162-974-11 CERAMIC CHIP 0.01uF 50VC128 1-126-382-11 ELECT 100uF 20% 16VC129 1-162-953-11 CERAMIC CHIP 100PF 5% 50VC130 1-162-953-11 CERAMIC CHIP 100PF 5% 50V
C144 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3VC145 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC146 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC147 1-126-382-11 ELECT 100uF 20% 16VC152 1-162-953-11 CERAMIC CHIP 100PF 5% 50V
C153 1-162-953-11 CERAMIC CHIP 100PF 5% 50VC154 1-162-953-11 CERAMIC CHIP 100PF 5% 50V
< CONNECTOR >
* CN001 1-568-450-11 HOUSING, CONNECTOR (PC BOARD) 4P* CN002 1-568-451-11 HOUSING, CONNECTOR (PC BOARD) 10P
CN003 1-784-749-11 CONNECTOR, FFC 27PCN004 1-784-735-11 CONNECTOR, FFC 13PCN005 1-779-550-21 CONNECTOR, FFC (LIF(NON-ZIF)) 13P
CN102 1-784-735-11 CONNECTOR, FFC 13PCN151 1-785-334-11 PIN, CONNECTOR (LIGHT ANGLE) 8PCN153 1-818-282-11 PIN, CONNECTOR (FOR PWB) 3P
< DIODE >
D101 6-500-335-01 DIODE MC2838-T112-1D102 6-500-335-01 DIODE MC2838-T112-1D105 6-501-193-01 DIODE 1SS355WTE-17D106 6-501-193-01 DIODE 1SS355WTE-17D107 6-501-193-01 DIODE 1SS355WTE-17
D108 1-216-295-11 SHORT CHIP 0D109 6-501-193-01 DIODE 1SS355WTE-17D110 8-719-053-43 LED SLR-325VCT31 (?/1)D111 6-501-193-01 DIODE 1SS355WTE-17D112 6-501-193-01 DIODE 1SS355WTE-17
JACK OPTICALMOTOR (TB)MOTOR (LD) PANEL
82
HCD-GNZ5D
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
D113 6-501-193-01 DIODE 1SS355WTE-17D114 6-501-193-01 DIODE 1SS355WTE-17D121 6-501-193-01 DIODE 1SS355WTE-17
< JUMPER RESISTOR >
FB101 1-216-295-11 SHORT CHIP 0FB102 1-216-295-11 SHORT CHIP 0FB103 1-216-295-11 SHORT CHIP 0FB104 1-216-295-11 SHORT CHIP 0FB105 1-216-295-11 SHORT CHIP 0
< FLUORESCENT INDICATOR TUBE >
FL101 1-519-811-11 INDICATOR TUBE, FLUORESCENT
< IC >
IC101 6-805-918-01 IC M30392MEP-A10FPU0IC102 6-707-095-01 IC BH2210FV-E2IC103 6-707-920-01 IC BD4828G-TR
< JUMPER RESISTOR >
JR101 1-216-864-11 SHORT CHIP 0JR104 1-216-864-11 SHORT CHIP 0JR105 1-216-864-11 SHORT CHIP 0JR106 1-216-864-11 SHORT CHIP 0JR107 1-216-864-11 SHORT CHIP 0
JR108 1-216-864-11 SHORT CHIP 0JR109 1-216-864-11 SHORT CHIP 0JR110 1-216-864-11 SHORT CHIP 0JR111 1-216-864-11 SHORT CHIP 0JR112 1-216-864-11 SHORT CHIP 0
JR118 1-216-864-11 SHORT CHIP 0JR119 1-216-864-11 SHORT CHIP 0JR120 1-216-864-11 SHORT CHIP 0JR121 1-216-864-11 SHORT CHIP 0JR123 1-216-864-11 SHORT CHIP 0
< TRANSISTOR >
Q101 8-729-039-14 TRANSISTOR BCR133W-GEG-E6327Q102 6-550-044-01 TRANSISTOR 2SB1689-T106Q103 8-729-039-14 TRANSISTOR BCR133W-GEG-E6327Q104 6-550-044-01 TRANSISTOR 2SB1689-T106Q105 8-729-039-14 TRANSISTOR BCR133W-GEG-E6327
Q106 6-550-044-01 TRANSISTOR 2SB1689-T106Q107 8-729-905-35 TRANSISTOR 2SC4081-RQ108 8-729-039-14 TRANSISTOR BCR133W-GEG-E6327Q109 8-729-026-53 TRANSISTOR 2SA1576A-T106-QRQ111 8-729-039-14 TRANSISTOR BCR133W-GEG-E6327
< RESISTOR >
R001 1-216-837-11 METAL CHIP 22K 5% 1/10WR002 1-216-809-11 METAL CHIP 100 5% 1/10WR003 1-216-809-11 METAL CHIP 100 5% 1/10WR004 1-216-809-11 METAL CHIP 100 5% 1/10WR005 1-216-809-11 METAL CHIP 100 5% 1/10W
R006 1-216-809-11 METAL CHIP 100 5% 1/10WR007 1-216-809-11 METAL CHIP 100 5% 1/10WR008 1-216-809-11 METAL CHIP 100 5% 1/10WR009 1-216-809-11 METAL CHIP 100 5% 1/10WR010 1-216-809-11 METAL CHIP 100 5% 1/10W
R011 1-216-809-11 METAL CHIP 100 5% 1/10WR012 1-216-809-11 METAL CHIP 100 5% 1/10WR013 1-216-833-11 METAL CHIP 10K 5% 1/10WR014 1-216-837-11 METAL CHIP 22K 5% 1/10WR015 1-216-841-11 METAL CHIP 47K 5% 1/10W
R016 1-216-833-11 METAL CHIP 10K 5% 1/10WR017 1-216-809-11 METAL CHIP 100 5% 1/10WR018 1-216-809-11 METAL CHIP 100 5% 1/10WR019 1-216-809-11 METAL CHIP 100 5% 1/10WR020 1-216-809-11 METAL CHIP 100 5% 1/10W
R021 1-216-809-11 METAL CHIP 100 5% 1/10WR022 1-216-809-11 METAL CHIP 100 5% 1/10WR023 1-216-809-11 METAL CHIP 100 5% 1/10WR024 1-216-809-11 METAL CHIP 100 5% 1/10WR025 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R026 1-216-809-11 METAL CHIP 100 5% 1/10WR027 1-216-837-11 METAL CHIP 22K 5% 1/10WR028 1-216-841-11 METAL CHIP 47K 5% 1/10WR029 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR030 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R031 1-216-833-11 METAL CHIP 10K 5% 1/10WR032 1-216-837-11 METAL CHIP 22K 5% 1/10WR033 1-216-841-11 METAL CHIP 47K 5% 1/10WR034 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR035 1-216-841-11 METAL CHIP 47K 5% 1/10W
R036 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR037 1-216-833-11 METAL CHIP 10K 5% 1/10WR038 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR039 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR040 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R041 1-216-813-11 METAL CHIP 220 5% 1/10WR042 1-216-815-11 METAL CHIP 330 5% 1/10WR043 1-216-817-11 METAL CHIP 470 5% 1/10WR044 1-216-819-11 METAL CHIP 680 5% 1/10WR045 1-216-821-11 METAL CHIP 1K 5% 1/10W
R046 1-216-823-11 METAL CHIP 1.5K 5% 1/10WR047 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR048 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR049 1-216-833-11 METAL CHIP 10K 5% 1/10WR050 1-216-839-11 METAL CHIP 33K 5% 1/10W
R051 1-216-819-11 METAL CHIP 680 5% 1/10WR052 1-216-821-11 METAL CHIP 1K 5% 1/10WR053 1-216-819-11 METAL CHIP 680 5% 1/10WR054 1-216-821-11 METAL CHIP 1K 5% 1/10WR055 1-216-819-11 METAL CHIP 680 5% 1/10W
R056 1-216-821-11 METAL CHIP 1K 5% 1/10WR057 1-216-833-11 METAL CHIP 10K 5% 1/10WR058 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR059 1-216-833-11 METAL CHIP 10K 5% 1/10WR060 1-216-833-11 METAL CHIP 10K 5% 1/10W
R061 1-216-813-11 METAL CHIP 220 5% 1/10WR062 1-216-815-11 METAL CHIP 330 5% 1/10WR063 1-216-817-11 METAL CHIP 470 5% 1/10WR064 1-216-823-11 METAL CHIP 1.5K 5% 1/10WR065 1-216-864-11 SHORT CHIP 0
R066 1-216-864-11 SHORT CHIP 0R067 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR068 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
PANEL
83
HCD-GNZ5D
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R070 1-216-819-11 METAL CHIP 680 5% 1/10WR071 1-216-821-11 METAL CHIP 1K 5% 1/10WR072 1-216-817-11 METAL CHIP 470 5% 1/10WR073 1-216-833-11 METAL CHIP 10K 5% 1/10WR074 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R075 1-216-837-11 METAL CHIP 22K 5% 1/10WR076 1-216-837-11 METAL CHIP 22K 5% 1/10WR077 1-216-841-11 METAL CHIP 47K 5% 1/10WR078 1-216-837-11 METAL CHIP 22K 5% 1/10WR079 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R080 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR081 1-216-813-11 METAL CHIP 220 5% 1/10WR082 1-216-815-11 METAL CHIP 330 5% 1/10WR083 1-216-817-11 METAL CHIP 470 5% 1/10WR084 1-216-819-11 METAL CHIP 680 5% 1/10W
R085 1-216-821-11 METAL CHIP 1K 5% 1/10WR086 1-216-823-11 METAL CHIP 1.5K 5% 1/10WR087 1-216-837-11 METAL CHIP 22K 5% 1/10WR088 1-216-841-11 METAL CHIP 47K 5% 1/10WR089 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R090 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR095 1-216-813-11 METAL CHIP 220 5% 1/10WR096 1-216-813-11 METAL CHIP 220 5% 1/10WR101 1-216-809-11 METAL CHIP 100 5% 1/10WR102 1-216-809-11 METAL CHIP 100 5% 1/10W
R103 1-216-809-11 METAL CHIP 100 5% 1/10WR104 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR105 1-216-809-11 METAL CHIP 100 5% 1/10WR106 1-216-809-11 METAL CHIP 100 5% 1/10WR107 1-216-809-11 METAL CHIP 100 5% 1/10W
R108 1-216-809-11 METAL CHIP 100 5% 1/10WR109 1-216-833-11 METAL CHIP 10K 5% 1/10WR110 1-216-841-11 METAL CHIP 47K 5% 1/10WR111 1-216-851-11 METAL CHIP 330K 5% 1/10WR112 1-216-833-11 METAL CHIP 10K 5% 1/10W
R113 1-216-811-11 METAL CHIP 150 5% 1/10W(E13)
R113 1-216-829-11 METAL CHIP 4.7K 5% 1/10W(E3,E12,E15)
R114 1-216-815-11 METAL CHIP 330 5% 1/10W(E3,E15)
R114 1-216-819-11 METAL CHIP 680 5% 1/10W(E12)
R114 1-216-829-11 METAL CHIP 4.7K 5% 1/10W(E13)
R114 1-216-864-11 SHORT CHIP 0 (PH)R115 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR116 1-216-864-11 SHORT CHIP 0R117 1-216-833-11 METAL CHIP 10K 5% 1/10WR118 1-216-809-11 METAL CHIP 100 5% 1/10W
R119 1-216-809-11 METAL CHIP 100 5% 1/10WR120 1-216-841-11 METAL CHIP 47K 5% 1/10WR121 1-216-809-11 METAL CHIP 100 5% 1/10WR122 1-216-809-11 METAL CHIP 100 5% 1/10WR123 1-216-809-11 METAL CHIP 100 5% 1/10W
R124 1-216-809-11 METAL CHIP 100 5% 1/10WR125 1-216-809-11 METAL CHIP 100 5% 1/10WR126 1-216-809-11 METAL CHIP 100 5% 1/10WR127 1-216-809-11 METAL CHIP 100 5% 1/10W
R128 1-216-809-11 METAL CHIP 100 5% 1/10WR129 1-216-809-11 METAL CHIP 100 5% 1/10WR130 1-216-809-11 METAL CHIP 100 5% 1/10WR131 1-216-841-11 METAL CHIP 47K 5% 1/10WR132 1-216-841-11 METAL CHIP 47K 5% 1/10W
R133 1-216-841-11 METAL CHIP 47K 5% 1/10WR134 1-216-841-11 METAL CHIP 47K 5% 1/10WR135 1-216-841-11 METAL CHIP 47K 5% 1/10WR136 1-216-841-11 METAL CHIP 47K 5% 1/10WR137 1-216-841-11 METAL CHIP 47K 5% 1/10W
R138 1-216-841-11 METAL CHIP 47K 5% 1/10WR139 1-216-841-11 METAL CHIP 47K 5% 1/10WR140 1-216-841-11 METAL CHIP 47K 5% 1/10WR141 1-216-841-11 METAL CHIP 47K 5% 1/10WR142 1-216-841-11 METAL CHIP 47K 5% 1/10W
R143 1-216-841-11 METAL CHIP 47K 5% 1/10WR144 1-216-841-11 METAL CHIP 47K 5% 1/10WR145 1-216-841-11 METAL CHIP 47K 5% 1/10WR146 1-216-841-11 METAL CHIP 47K 5% 1/10WR147 1-216-841-11 METAL CHIP 47K 5% 1/10W
R148 1-216-841-11 METAL CHIP 47K 5% 1/10WR149 1-216-841-11 METAL CHIP 47K 5% 1/10WR150 1-216-841-11 METAL CHIP 47K 5% 1/10WR151 1-216-841-11 METAL CHIP 47K 5% 1/10WR152 1-216-864-11 SHORT CHIP 0
R153 1-216-841-11 METAL CHIP 47K 5% 1/10WR154 1-216-841-11 METAL CHIP 47K 5% 1/10WR155 1-216-841-11 METAL CHIP 47K 5% 1/10WR156 1-216-841-11 METAL CHIP 47K 5% 1/10WR157 1-216-841-11 METAL CHIP 47K 5% 1/10W
R158 1-216-841-11 METAL CHIP 47K 5% 1/10WR159 1-216-841-11 METAL CHIP 47K 5% 1/10WR160 1-216-841-11 METAL CHIP 47K 5% 1/10WR161 1-216-841-11 METAL CHIP 47K 5% 1/10WR162 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R163 1-216-841-11 METAL CHIP 47K 5% 1/10WR164 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR165 1-216-841-11 METAL CHIP 47K 5% 1/10WR166 1-216-841-11 METAL CHIP 47K 5% 1/10WR167 1-216-841-11 METAL CHIP 47K 5% 1/10W
R168 1-216-809-11 METAL CHIP 100 5% 1/10WR169 1-216-809-11 METAL CHIP 100 5% 1/10WR170 1-216-809-11 METAL CHIP 100 5% 1/10WR171 1-216-809-11 METAL CHIP 100 5% 1/10WR172 1-216-833-11 METAL CHIP 10K 5% 1/10W
R173 1-216-833-11 METAL CHIP 10K 5% 1/10WR174 1-216-857-11 METAL CHIP 1M 5% 1/10WR175 1-216-864-11 SHORT CHIP 0R177 1-216-853-11 METAL CHIP 470K 5% 1/10WR178 1-216-809-11 METAL CHIP 100 5% 1/10W
R179 1-216-809-11 METAL CHIP 100 5% 1/10WR180 1-216-809-11 METAL CHIP 100 5% 1/10WR181 1-216-809-11 METAL CHIP 100 5% 1/10WR182 1-216-809-11 METAL CHIP 100 5% 1/10WR183 1-216-809-11 METAL CHIP 100 5% 1/10W
R184 1-216-809-11 METAL CHIP 100 5% 1/10WR185 1-216-809-11 METAL CHIP 100 5% 1/10WR186 1-216-809-11 METAL CHIP 100 5% 1/10W
PANEL
84
HCD-GNZ5D
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R187 1-216-809-11 METAL CHIP 100 5% 1/10WR188 1-216-809-11 METAL CHIP 100 5% 1/10WR189 1-216-809-11 METAL CHIP 100 5% 1/10WR192 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR193 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R194 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR195 1-216-809-11 METAL CHIP 100 5% 1/10WR197 1-216-809-11 METAL CHIP 100 5% 1/10WR198 1-216-864-11 SHORT CHIP 0R199 1-216-821-11 METAL CHIP 1K 5% 1/10W
R200 1-216-809-11 METAL CHIP 100 5% 1/10W
< SWITCH >
S11 1-762-875-21 SWITCH, KEYBOARD (?/1)S12 1-762-875-21 SWITCH, KEYBOARD (EQ BAND/MEMORY)S14 1-762-875-21 SWITCH, KEYBOARD (PRESET EQ)S15 1-762-875-21 SWITCH, KEYBOARD (DIRECTION)S16 1-762-875-21 SWITCH, KEYBOARD (DISC 3)
S17 1-762-875-21 SWITCH, KEYBOARD (DISC 2)S18 1-762-875-21 SWITCH, KEYBOARD (DISC 1)S19 1-762-875-21 SWITCH, KEYBOARD (DISC SKIP/EX-CHANGE)S20 1-762-875-21 SWITCH, KEYBOARD (Z OPEN/CLOSE)S31 1-762-875-21 SWITCH, KEYBOARD (DISPLAY)
S32 1-762-875-21 SWITCH, KEYBOARD (TUNER/BAND)S33 1-762-875-21 SWITCH, KEYBOARD (TAPE A/B)S34 1-762-875-21 SWITCH, KEYBOARD (CD SYNC)S35 1-762-875-21 SWITCH, KEYBOARD (REC PAUSE/START)S38 1-762-875-21 SWITCH, KEYBOARD ( m TUNING –)
S51 1-762-875-21 SWITCH, KEYBOARD (Y)S52 1-762-875-21 SWITCH, KEYBOARD (SOUND FIELD)S53 1-762-875-21 SWITCH, KEYBOARD (X)S54 1-762-875-21 SWITCH, KEYBOARD (x)S55 1-762-875-21 SWITCH, KEYBOARD (M y TUNING +)
S56 1-762-875-21 SWITCH, KEYBOARD (GROOVE)S57 1-762-875-21 SWITCH, KEYBOARD (DVD)
< VIBRATOR >
X101 1-795-482-11 VIBRATOR, CERAMIC (16MHz)X102 1-760-252-12 VIBRATOR, CRYSTAL (32.768kHz)
*************************************************************
1-687-132-12 SENSOR BOARD**************
< CONNECTOR >
CN731 1-785-329-21 PIN, CONNECTOR (LIGHT ANGLE) 3P
< IC >
IC731 6-600-022-01 IC RPI-576*************************************************************
SIRCS BOARD************
< CAPACITOR >
C148 1-162-974-11 CERAMIC CHIP 0.01uF 50V
< CONNECTOR >
CN143 1-816-423-11 SOCKET, CONNECTOR 3P
< IC >
IC104 6-600-309-01 IC RPM7240-H9 (IR)
< JUMPER RESISTOR >
JR102 1-216-864-11 SHORT CHIP 0*************************************************************
STREAM BOARD**************
< DIODE >
D117 8-719-085-33 LED SLI-343URCT32WST(RING ILLUMINATION)
D118 8-719-085-33 LED SLI-343URCT32WST(RING ILLUMINATION)
< JUMPER RESISTOR >
JR113 1-216-864-11 SHORT CHIP 0JR114 1-216-864-11 SHORT CHIP 0JR115 1-216-864-11 SHORT CHIP 0JR116 1-216-864-11 SHORT CHIP 0JR117 1-216-864-11 SHORT CHIP 0
< RESISTOR >
R069 1-216-833-11 METAL CHIP 10K 5% 1/10W
< SWITCH >
S101 1-786-289-11 SWITCH, DETECTION (l – EQ + L)
< ROTARY ENCODER >
S102 1-418-725-41 ENCODER, ROTARY (12 TYPE)(MASTER VOLUME)
*************************************************************
SUB TRANS BOARD****************
1-533-217-41 HOLDER, FUSE (E3,E15,PH)
< CAPACITOR >
C902 1-164-159-11 CERAMIC 0.1uF 50VC903 1-164-159-11 CERAMIC 0.1uF 50V
< CONNECTOR >
CN901 1-564-321-00 PIN, CONNECTOR (3.96mm PITCH) 2PCN902 1-785-314-11 PIN, CONNECTOR (STRAIGHT) 2P
< DIODE >
D901 8-719-991-33 DIODE 1SS133T-77
< COIL >
L901 1-414-189-31 INDUCTOR 100uH
PANEL
y
SENSOR SIRCS STREAM SUB TRANS
85
HCD-GNZ5D
Ref. No. Part No. Description Remark
< TRANSISTOR >
Q901 8-729-119-78 TRANSISTOR 2SC2785-HFE
< RESISTOR >
R901 1-249-429-11 CARBON 10K 5% 1/4WR904 1-249-393-11 CARBON 10 5% 1/4W
< RELAY >
0RY901 1-755-324-11 RELAY
< SWITCH >
0S901 1-786-055-21 SELECTOR, VOLTAGE (VOLTAGE SELECTOR)(E3,E15,PH)
*************************************************************
1-687-669-12 SW BOARD**********
< SWITCH >
S751 1-786-514-11 SWITCH, LEVER (SLIDE) (OPEN/CLOSE DET)*************************************************************
TRANS BOARD*************
1-533-217-41 HOLDER, FUSE
< CAPACITOR >
C912 1-126-960-11 ELECT 1uF 20% 50V(E12,E13)
C913 1-126-968-11 ELECT 100uF 20% 50VC915 1-164-159-11 CERAMIC 0.1uF 50VC918 1-128-576-11 ELECT 100uF 20% 63V
< CONNECTOR >
* CN914 1-564-525-11 PLUG, CONNECTOR 10P* CN915 1-564-519-11 PLUG, CONNECTOR 4P
< DIODE >
D911 6-500-522-11 DIODE 10EDB40-TA2B5D912 8-719-982-19 DIODE MTZJ-30AD913 8-719-118-64 DIODE RD5.6F-T7B3
< TRANSISTOR >
Q902 8-729-140-97 TRANSISTOR 2SB734-34
< RESISTOR >
0R911 1-217-637-00 FUSIBLE 1 5% 1/4W FR914 1-249-429-11 CARBON 10K 5% 1/4WR915 1-247-807-31 CARBON 100 5% 1/4WR916 1-247-807-31 CARBON 100 5% 1/4WR919 1-249-429-11 CARBON 10K 5% 1/4W
*************************************************************
A-1109-328-A VIDEO BOARD, COMPLETE**********************
< CAPACITOR >
C801 1-104-655-11 ELECT 470uF 20% 6.3VC802 1-162-306-11 CERAMIC 0.01uF 20% 16VC811 1-126-960-11 ELECT 1uF 20% 50VC812 1-126-916-11 ELECT 1000uF 20% 6.3VC813 1-162-282-31 CERAMIC 100PF 10% 50V
C840 1-162-282-31 CERAMIC 100PF 10% 50VC841 1-162-282-31 CERAMIC 100PF 10% 50VC842 1-162-282-31 CERAMIC 100PF 10% 50VC850 1-126-942-61 ELECT 1000uF 20% 25VC851 1-164-159-11 CERAMIC 0.1uF 50V
C852 1-117-245-11 ELECT 330uF 20% 6.3VC853 1-126-960-11 ELECT 1uF 20% 50VC854 1-164-159-11 CERAMIC 0.1uF 50VC856 1-117-245-11 ELECT 330uF 20% 6.3VC862 1-117-317-11 ELECT 1000uF 20% 25V
C863 1-128-646-11 ELECT 1000uF 20% 6.3VC865 1-117-245-11 ELECT 330uF 20% 6.3VC866 1-117-245-11 ELECT 330uF 20% 6.3VC872 1-164-159-11 CERAMIC 0.1uF 50VC873 1-104-658-11 ELECT 100uF 20% 10V
< CONNECTOR >
CN801 1-779-273-11 CONNECTOR, FFC (LIF(NON-ZIF)) 5P* CN851 1-564-724-11 PIN, CONNECTOR (SMALL TYPE) 8P
< DIODE >
D861 8-719-210-21 DIODE 11EQS04
< GROUND TERMINAL >
EP801 1-537-771-21 TERMINAL BOARD, GROUNDEP851 1-537-771-21 TERMINAL BOARD, GROUND
< IC >
IC801 6-600-495-01 IC MM1671XNREIC851 6-705-463-01 IC BA33BC0TIC861 8-759-474-09 IC SI-8050S-LF1101
< JACK >
J801 1-794-970-11 JACK, PIN 1P (VIDEO OUT)
< COIL >
L801 1-410-470-11 INDUCTOR 10uHL861 1-456-513-11 INDUCTOR 150uHL862 1-414-741-11 INDUCTOR 10uH
< TRANSISTOR >
Q861 8-729-029-66 TRANSISTOR DTC114ESAQ870 8-729-029-66 TRANSISTOR DTC114ESA
< RESISTOR >
R801 1-249-429-11 CARBON 10K 5% 1/4WR811 1-247-804-11 CARBON 75 5% 1/4WR812 1-247-879-11 CARBON 100K 5% 1/4W
Ref. No. Part No. Description Remark
SUB TRANS SW TRANS VIDEO
86
HCD-GNZ5D
R870 1-247-807-31 CARBON 100 5% 1/4WR871 1-249-429-11 CARBON 10K 5% 1/4W
*************************************************************
MISCELLANEOUS***************
7 1-828-956-11 WIRE (FLAT TYPE) (9 CORE)55 1-828-977-11 WIRE (FLAT TYPE) (13 CORE)56 1-828-971-11 WIRE (FLAT TYPE) (13 CORE)57 1-829-041-11 WIRE (FLAT TYPE) (27 CORE)58 1-797-246-11 DECK, MECHANISM
59 1-828-332-11 WIRE (FLAT TYPE) (13 CORE)202 1-828-354-11 WIRE (FLAT TYPE) (17 CORE)203 1-828-290-11 WIRE (FLAT TYPE) (5 CORE)
0254 1-777-071-23 CORD, POWER (E12,E13,PH)0254 1-827-226-31 CORD, POWER (E3,E15)
0255 1-468-737-21 POWER, SWITCHING352 1-776-182-11 WIRE (FLAT TYPE) (5 CORE)421 1-828-771-51 WIRE (FLAT TYPE) (24 CORE)
0422 8-820-291-02 OPTICAL PICK-UP (KHM-310CAB/C2RP)0F910 1-532-504-33 FUSE (4A/250V) (E3,E15,PH)
0F914 1-532-506-33 FUSE (6.3A/250V)0F915 1-532-506-33 FUSE (6.3A/250V)0F918 1-532-504-33 FUSE (4A/250V)0F919 1-532-504-33 FUSE (4A/250V)
FAN901 1-763-072-11 FAN, DC
IC941 8-759-198-03 IC PQ09RF21J00HIC942 8-759-701-59 IC NJM78M09FAIC943 8-759-701-59 IC NJM78M09FAIC945 6-703-546-01 IC TA7804LSM741 A-1108-965-A MOTOR ASSY, TABLE (TABLE)
M751 A-1108-966-A MOTOR ASSY, LOADING (LOADING)RE701 1-477-680-12 ENCODER, ROTARY (DISC TRAY ADDRESS
DETECT)0T911 1-443-792-11 TRANSFORMER, POWER
TN1 1-693-671-11 TUNER (FM/AM) (TM-10E)
Ref. No. Part No. Description Remark
VIDEO
87
HCD-GNZ5D
MEMO
88
HCD-GNZ5D
REVISION HISTORY
Clicking the version allows you to jump to the revised page.Also, clicking the version at the upper on the revised page allows you to jump to the next revised page.
Ver. Date Description of Revision1.0 2005. 08 New
1.1 2005. 12DVD section electrical adjustment alteration.Addition of note on DMB11 board replacement. (SPM-05077)