AVR 240 Audio/VideoReceiverOWNERS MANUAL

Power for the Digital Revolution

2 TABLE OF CONTENTS

3 Introduction4 Safety Information4 Unpacking5 Front Panel Controls7 Rear Panel Connections9 Main Remote Control Functions

12 Installation and Connections12 Audio Connections12 Video Connections13 SCART A/V Connections14 System and Power Connections15 Speaker Selection15 Speaker Placement16 System Configuration16 First Turn On16 Using the On-Screen Display16 System Setup17 Input Setup18 Audio Setup18 Surround Setup19 Night Mode Settings20 Configuring the Surround Off

(Stereo) Modes20 Automated Speaker Setup Using EzSet+22 Manual Setup23 Speaker Setup26 Delay Settings27 Output Level Adjustment30 Operation30 Surround Mode Chart32 Basic Operation32 Source Selection32 6/8-Channel Direct Input32 Controls and Use of Headphones33 Surround Mode Selection33 Digital Audio Playback33 Dolby Digital34 DTS34 PCM Audio Playback34 Selecting a Digital Source34 Digital Bitstream Indicators34 Surround mode Types35 PCM Playback Indications35 Speaker/Channel Indicators36 Night Mode36 Tape Recording36 Using The Bridge 36 Output Level Adjustment

With Source Signals37 Memory backup37 Advanced Features37 Front Panel Display Fade38 Turn-On Volume Level38 Semi-OSD Settings38 Full-OSD Time Out Adjustment39 Default Surround Mode39 Full-OSD Background Color39 Tuner Operation39 Basic Tuner Operation39 Station Selection39 Preset Tuning40 RDS Operation40 RDS Tuning40 RDS Display Options

Table of Contents

Typographical ConventionsIn order to help you use this manual with the remote control, front-panel controls and rear-panelconnections, certain conventions have been used.

EXAMPLE (bold type) indicates a specific remote control or front-panel button, or rear-panel connection jack

EXAMPLE (OCR type) indicates a message that is visible on the front-panel information display

1 (number in a square) indicates a specific front-panel control

(number in a circle) indicates a rear-panel connection

0 (number in an oval) indicates a button or indicator on the remote

The appearance of the text or cursor for your receivers on-screen menus may vary slightly from theillustrations in this manual. Whether the text appears in all uppercase or upper- and lowercasecharacters, performance and operation remain the same.

Declaration of Conformity

We, Harman Consumer Group International2, route de Tours72500 Chteau-du-Loir,FRANCE

declare in own responsibility, that the productdescribed in this owners manual is in compliancewith technical standards:

EN 55013:2001 + A1:2003EN 55020:2002 + A1:2003EN 61000-3-2:2000EN 61000-3-3:1995 + A1:2001EN 60065:2002

Jurjen AmsterdamHarman Consumer Group International

07/05

40 Program Search41 Programming the Remote41 Programming the Remote with Codes41 Direct Code Entry41 Auto Search Method41 Code Readout42 Macro Programming42 Programmed Device Functions42 Volume Punch-Through

43 Channel Control Punch-Through43 Transport Control Punch-Through43 Resetting the Remote Memory44 Function List46 Troubleshooting Guide46 Processor Reset47 Technical Specifications48 Appendix - Settings Worksheet

INTRODUCTION 3

Introduction

Thank you for choosing Harman Kardon! With the purchase of a Harman Kardon AVR 240 you are about to begin many years oflistening enjoyment. Designed to provide all theexcitement and detail of movie soundtracks andevery nuance of musical selections, the AVR 240is truly a multichannel receiver for the newmillennium. In addition to the traditional 5.1digital decoding modes such as Dolby Digitaland DTS, it offers the latest advancements insurround technology such as Dolby Pro Logic IIand IIx, the full suite of DTS-ES 6.1 modes, DTSNeo:6 and the latest 7.1 channel versions ofHarman's own Logic 7 technology.

The AVR 240 has been engineered so that it iseasy to take advantage of all the power of itsdigital technology. On-screen menus, fully colorcoded connection jacks and terminals makeinstallation fast and simple. However, to obtainthe maximum enjoyment from your new receiv-er, we urge you to read this manual. A few min-utes spent learning the functions of the variouscontrols will enable you to take advantage of allthe power the AVR 240 is able to deliver.

If you have any questions about this product, itsinstallation or its operation, please contact yourretailer or custom installer. They are your bestlocal sources of information.

Description and FeaturesThe AVR 240 is among the most versatile andmultifeatured A/V receivers available, incorporat-ing a wide range of listening options. In additionto Dolby Digital and DTS decoding for digitalsources, a broad choice of surround modes forMatrix surround-encoded or Stereo recordingsare available for use with sources such as CD,VCR, TV broadcasts and the AVRs own FM/AMtuner. Along with Dolby Digital EX, Dolby ProLogic II and IIx, DTS Neo:6, DTS 96/24, Dolby 3Stereo, 5 Channel or 7 Channel Stereo and Halland Theater modes, the AVR offers HarmanInternationals exclusive Logic 7 process in both5.1 and 7.1 versions to create a wider, moreenveloping field environment and more definedfly-overs and pans. Although the AVR 240sprimary use will be in multichannel systems,advanced technology is at work even when onlytwo speakers are used, with Harman Inter-nationals proprietary VMAx creating envelop-ing sound fields from front left and right speak-ers only.

Dolby Virtual Speaker is available to createenveloping sound fields from front left and rightspeakers, and the latest Dolby Headphone cir-cuitry creates an amazing sense of opennesswith headphones.

In addition to providing a wide range of listeningoptions, the AVR is easy to configure so that itprovides the best results with your speakers andspecific listening-room environment.

On-screen menus combine with the EzSet+system to automate speaker configuration andoverall setup, resulting in a perfectly balancedsound field presentation that accuratelyreproduces the artists intent.

A Stereo-Direct mode bypasses the digitalprocessor to preserve all of the subtleties ofolder analog, two-channel materials, while bassmanagement, available in the surround andStereo-Digital modes,improves your ability totailor the sound to suit your room acoustics ortaste.

For the ultimate in flexibility, the AVR featuresconnections for five video devices, all with bothcomposite and S-Video inputs. Two additionalaudio inputs are available, and a total of sixdigital inputs and two outputs make the AVR 240 capable of handling all the latestdigital audio sources.For compatibility with the latest HDTV videosources and progressive scan DVD players, theAVR also features wide-bandwidth,low-crosstalk component video switching.

Coax and optical digital outputs are available fordirect connection to digital recorders. A videorecording output and a color-coded eight-chan-nel input make the AVR 240 virtually future-proof, with everything needed to accommodatetomorrows new formats right on board.

Until now, Harman Kardon AVRs have been ableto accommodate almost any source deviceequipped with line-level analog, optical digitalor coaxial digital outputs, including most digitalmedia players. With one simple connectionbetween the AVR 240 and the optional Harman Kardon , you are able to listento materials stored on your compatible Apple

iPod**. Your AVRs system remote control hasbeen preprogrammed with control codes thatenable you to select tracks for playback andnavigate many of your iPods functions, evenfrom across the room. The Bridge will even letyou charge your iPod.

The AVR 240s powerful amplifier usestraditional Harman Kardon high-current designtechnologies to meet the wide dynamic range ofany program selection.

Harman Kardon invented the high-fidelity receiver more then fifty years ago. With state-of-the-art circuitry and time-honored circuitdesigns, the AVR 240 is the perfect combinationof the latest in digital audio technology, a quietyet powerful analog amplifier in an elegant,easy-to-use package.

Dolby* Digital, Dolby Digital EX andDolby Pro Logic* II and IIx Decoding,and the full suite of DTS modes,including DTS-ES 6.1 Discrete & Matrixand Neo:6

Seven channels of high-currentamplification

Harman Kardons exclusive Logic 7processing, available for the first timewith both 7.1 and 5.1 processing in a variety of modes and two modes of VMAx

system with included micro-phone automatically configures speak-ers and sets delay times and outputlevels for optimal sound presentation

Stereo-Direct Mode for Two-ChannelSources Bypasses DSP Processing toPreserve the Integrity of AnalogMaterials

Stereo-Digital Mode for ProgrammableBass Management of Low FrequenciesBetween Main Speakers andSubwoofer

High-bandwidth, HDTV-compatiblecomponent video switching

Front panel analog A/V inputs Front panel digital inputs for easy con-

nection to portable digital devices andthe latest video game consoles

Connects to Harman Kardons (optional) for charging, playback andcontrol of a compatible Apple iPod

device

Input titling for all input sources(except tuner)

Multiple digital inputs and outputs On-screen menu and display system

with choice of blue or black back-ground screen

6-Channel/8-Channel Direct InputforUse with Future Audio Formats

Extensive bass management options,including four separate crossovergroupings

Main Remote with Internal Codes

4 SAFETY INFORMATION

Safety Information

Important Safety Information

Verify Line Voltage Before UseYour AVR has been designed for use with 220-240-Volt AC current. Connection to a linevoltage other than that for which it is intendedcan create a safety and fire hazard and maydamage the unit.

If you have any questions about the voltagerequirements for your specific model, or aboutthe line voltage in your area, contact your dealerbefore plugging the unit into a wall outlet.

Do Not Use Extension CordsTo avoid safety hazards, use only the power cordattached to your unit. We do not recommendthat extension cords be used with this product.As with all electrical devices, do not run powercords under rugs or carpets or place heavyobjects on them. Damaged power cords shouldbe replaced immediately by an authorizedservice depot with a cord meeting factoryspecifications.

Handle the AC Power Cord GentlyWhen disconnecting the power cord from an ACoutlet, always pull the plug, never pull the cord.If you do not intend to use the unit for anyconsiderable length of time, disconnect the plugfrom the AC outlet.

Do Not Open the CabinetThere are no user-serviceable components insidethis product. Opening the cabinet may present ashock hazard, and any modification to theproduct will void your guarantee. If water or anymetal object such as a paper clip, wire or astaple accidentally falls inside the unit,disconnect it from the AC power sourceimmediately, and consult an authorized servicestation.

Installation Location To assure proper operation and to avoid the

potential for safety hazards, place the unit ona firm and level surface. When placing theunit on a shelf, be certain that the shelf andany mounting hardware can support theweight of the product.

Make certain that proper space is providedboth above and below the unit for ventilation.If this product will be installed in a cabinet orother enclosed area, make certain that thereis sufficient air movement within the cabinet.Under some circumstances a fan may berequired.

Do not place the unit directly on a carpetedsurface.

Avoid installation in extremely hot or coldlocations, or an area that is exposed to directsunlight or heating equipment.

Avoid moist or humid locations. Do not obstruct the ventilation slots on the

top of the unit, or place objects directly overthem.

Due to the weight of the AVR 240 and theheat generated by the amplifiers, there is theremote possibility that the rubber padding onthe bottom of the units feet may leave markson certain wood or veneer materials. Use cau-tion when placing the unit on soft woods orother materials that may be damaged by heator heavy objects. Some surface finishes maybe particularly sensitive to absorbing suchmarks due to a variety of factors beyondHarman Kardon's control, including thenature of the finish, cleaning materials used,and normal heat and vibration caused by theuse of the product, or other factors. We rec-ommend that cau-tion be exercised in choos-ing an installation location for the componentand in normal maintenance practices, as yourwarranty will not cover this type of damage tofurniture.

CleaningWhen the unit gets dirty, wipe it with a clean,soft, dry cloth. If necessary, wipe it with a softcloth dampened with mild soapy water, then afresh cloth with clean water. Wipe dryimmediately with a dry cloth. NEVER usebenzene, aerosol cleaners, thinner, alcohol or anyother volatile cleaning agent. Do not useabrasive cleaners, as they may damage the finishof metal parts. Avoid spraying insecticide nearthe unit.

Moving the UnitBefore moving the unit, be certain to disconnectany interconnection cords with othercomponents, and make certain that youdisconnect the unit from the AC outlet.

Unpacking

The carton and shipping materials used toprotect your new receiver during shipment werespecially designed to cushion it from shock andvibration. We suggest that you save the cartonand packing materials for use in shipping if youmove, or should the unit ever need repair.

To minimize the size of the carton in storage,you may wish to flatten it. This is done bycarefully slitting the tape seams on the bottomand collapsing the carton. Other cardboardinserts may be stored in the same manner.Packing materials that cannot be collapsedshould be saved along with the carton in aplastic bag.

If you do not wish to save the packagingmaterials, please note that the carton and othersections of the shipping protection arerecyclable. Please respect the environment anddiscard those materials at a local recyclingcenter.

It is important that you remove the protectiveplastic film from the front-panel lens. Leavingthe film in place will affect the performance ofyour remote control.

FRONT PANEL CONTROLS 5

1 Main Power Switch: Press this button toapply power to the AVR. When the switch ispressed in, the unit is placed in a Standbymode, as indicated by the orange LED 3. Thisbutton MUST be pressed in to operate the unit.To turn the unit off completely and prevent theuse of the remote control, this switch should bepressed until it pops out from the front panel sothat the word OFF may be read at the top ofthe switch.

NOTE: This switch is normally left in the ONposition.

2 System Power Control: When the MainPower Switch 1 is ON, press this button toturn on the AVR; press it again to turn the unitoff (to Standby). Note that the Power Indicator3 will turn blue when the unit is on.

3 Power Indicator: This LED will be illuminatedin orange when the unit is in the Standby modeto signal that the unit is ready to be turned on.When the unit is in operation, the indicator willturn blue.

4 Headphone Jack: This jack may be used tolisten to the AVRs output through a pair of head-phones. Be certain that the headphones have astandard 6.3 mm stereo phone plug. Note thatthe speakers will automatically be turned offwhen the headphones are connected.

When configuring your system using EzSet+, thecalibration microphone should be plugged intothis jack using the supplied adaptor that convertsthe small mini-plug at the end of the micro-phones cord to a 1/4" plug.

5 Surround Mode Group Selector: Pressthis button to select the top-level group ofsurround modes. Each press of the button willselect a major mode grouping in the followingorder:

Dolby Modes DTS Digital Modes DSPModes Stereo Modes Logic 7 Modes

Once the button is pressed so that the name ofthe desired surround mode group appears in theMain Information Display , press theSurround Mode Selector 9 to cycle throughthe individual modes available. For example, pressthis button to select Dolby modes, and then pressthe Surround Mode Selector 9 to choosefrom the various mode options.

6 Speaker Select Button: Press this buttonto begin the process of selecting the speakerpositions that are used in your listening room.(See page 16 for more information on setup andconfiguration.)

Front Panel Controls

1234 5 67 8 9 )

! @ # $ % ^ & * (

Main Power SwitchSystem Power ControlPower IndicatorHeadphone JackSurround Mode Group SelectorSpeaker Select ButtonSelector ButtonsTone ModeSurround Mode SelectorTuning

Tuner Band SelectorSet ButtonPreset Stations SelectorSpeaker/Channel Input IndicatorInput Source SelectorRDS Select ButtonDelayDigital Optical 3 InputSurround Mode IndicatorsDigital Coax 3 Input

Video 4 input jacksInput IndicatorsMain Information DisplayRemote Sensor WindowDigital Input SelectorChannel Select ButtonVolume Control

6 FRONT PANEL CONTROLS

Front Panel Controls

7 Selector Buttons: When you are establishingthe AVRs configuration settings, use these buttonsto select from the choices available, as shown inthe Main Information Display .

8 Tone Mode: Pressing this button enables ordisables the Balance, Bass and Treble tonecontrols. When the button is pressed so that thewords TONEIN appear in the MainInformation Display , the settings of theBass and Treble controls and of the Balancecontrol will affect the output signals. When thebutton is pressed so that the words TONEOUT appear in the Main InformationDisplay , the output signal will be flat,without any balance, bass or treble alteration.

9 Surround Mode Selector: Press this buttonto select from among the available surroundmode options for the mode group selected. Thespecific modes will vary based on the number ofspeakers available, the mode group and if theinput source is digital or analog. For example,press the Surround Mode Group Selector 5to select a mode grouping such as Dolby or Logic7, and then press this button to see the modechoices available. For more information on modeselection, see page 33.

) Tuning Selector: Press the left side of thebutton to tune lower frequency stations and theright side of the button to tune higher frequencystations. When a station with a strong signal isreached, MANUALTUNED or AUTOTUNEDwill appear in the Main InformationDisplay (see page 40 for more informationon tuning stations).

! Tuner Band Selector: Pressing this buttonwill automatically switch the AVR to the Tunermode. Pressing it again will switch between theAM and FM frequency bands, holding it pressedfor some seconds will switch between stereo andmono receiving and between automatic andmanual tuning mode (See page 39 for moreinformation on the tuner).

@ Set Button: When making choices during thesetup and configuration process, press this buttonto enter the desired setting as shown in the Main Information Display into the AVRsmemory.

# Preset Stations Selector: Press thisbutton to scroll up or down through the list ofstations that have been entered into the presetmemory (See page 39 for more information ontuner programming).

$ Speaker/Channel Input Indicators: Theseindicators are multipurpose, indicating either thespeaker type selected for each channel or theincoming data-signal configuration. The left, center,right, right surround and left surround speakerindicators are composed of three boxes, while thesubwoofer is a single box. The center box lightswhen a Small speaker is selected, and the twoouter boxes light when Large speakers areselected. When none of the boxes are lit for thecenter, surround or subwoofer channels, no speakerhas been selected for that position. (See page 23for more information on configuring speakers.) Theletters inside each of the center boxes displayactive input channels. For standard analog inputs,only the L and R will light, indicating a stereoinput. When a digital source is playing, the indica-tors will light to display the channels beginreceived at the digital input. When the lettersflash, the digital input has been interrupted.(See page 26 for more information on the ChannelIndicators).

% Input Source Selector: Press this button tochange the input by scrolling through the list ofinput sources.

^ RDS Select Button: Press this button todisplay the various messages that are part of theRDS data system of the AVRs tuner.(See page 40 for more information on RDS).

& Delay: Press this button to begin thesequence of steps required to enter delay timesettings (See page 26 for more information ondelay times).

* Digital Optical 3 Input: Connect the opticaldigital audio output of an audio or video productto this jack. When the Input is not in use, becertain to keep the plastic cap installed to avoiddust contamination that might degrade future performance.

( Surround Mode Indicators: The currentselected mode or function will appear as one ofthese indicators. Note that when the unit isturned on, the entire list of available modes willlight briefly, and then revert to normal operationwith only the active mode indicator illuminated.

Digital Coax 3 Input: This jack is normallyused for connection to the output of portabledigital audio devices, video game consoles orother products that have a coax digital jack.

Video 4 Input Jacks: These audio/videojacks may be used for temporary connection tovideo games or portable audio/video productssuch as camcorders and portable audio players.

Input indicators: The current selectedmode or function will appear as one of theseindicators. Note that when the unit is turned on,the entire list of available modes will light briefly,and then revert to normal operation with onlythe active mode indicator illuminated.

Main Information Display: This displaydelivers messages and status indications to helpyou operate the receiver.

Remote Sensor Window: The sensorbehind this window receives infrared signals fromthe remote control. Aim the remote at this areaand do not block or cover it unless an externalremote sensor is installed.

Note: When /DMP has been selected as the input source, no Input Indicator willlight. DMP/THEBRIDGEISCONNECTEDwill scroll across the UpperDisplay Line , unless you have retitled thesource name, in which case that name willappear. See page 17 for more information oninput titling.

Digital Input Selector: When playing asource that has a digital output, press this buttonto select between the Optical and Coaxial Digital inputs. (See pages 17 and 33 formore information on digital audio).

Channel Select Button: Press this buttonto begin the process of trimming the channeloutput levels using an external audio source.(For more information on output level trimadjustment, see page 36).

Volume Control: Turn this knob clockwiseto increase the volume, counterclockwise todecrease the volume. If the AVR is muted, adjust-ing volume control will automatically release theunit from the silenced condition.

REAR PANEL CONNECTIONS 7

Rear Panel Connections

!"#$%&

AM AntennaFM AntennaTape InputsTape OutputsSubwoofer OutputDVD Audio InputsCD InputsVideo 1 Audio Outputs

DMP Connector8-Channel Direct InputsDigital Audio OutputsVideo Monitor OutputsDVD Video Inputs

Front Speaker OutputsCenter Speaker OutputsSurround Speaker OutputsSwitched AC Accessory OutletUnswitched AC Accessory OutletAC Power CordVideo 2 Component Video InputsComponent Video OutputsVideo 1 Component Video InputsVideo 2 Audio InputsCoaxial Digital InputsSurround Back Speaker OutputsVideo 1 Video Outputs

Video 1 Video InputsOptical Digital InputsVideo 1 Audio InputsVideo 2 Video InputsRemote IR OutputRemote IR InputPreamp OutputsVideo 2 Video OutputsVideo 3 Video InputsVideo 3 Audio InputsVideo 2 Audio Outputs

NOTE: To assist in making the correct connec-tions for multichannel input/output and speakerconnections, all connection jacks and terminalshave been color coded in conformance with thelatest CEA standards as follows:Front Left: WhiteFront Right: RedCenter: GreenSurround Left: BlueSurround Right: GraySurround Back Left: BrownSurround Back Right: TanSubwoofer (LFE): PurpleDigital Audio: OrangeComposite Video: YellowComponent Video Y: GreenComponent Video Pr: RedComponent Video Pb: Blue

AM Antenna: Connect the AM loop antennasupplied with the receiver to these terminals. If anexternal AM antenna is used, make connections tothe AM and GND terminals in accordance withthe instructions supplied with the antenna.

FM Antenna: Connect the supplied indoor oran optional external FM antenna to this terminal.

Tape Inputs: Connect these jacks to thePLAY/OUT jacks of an audio recorder.

Tape Outputs: Connect these jacks to theRECORD/INPUT jacks of an audio recorder.

Subwoofer Output: Connect this jack tothe line-level input of a powered subwoofer. If anexternal subwoofer amplifier is used, connect thisjack to the subwoofer amplifier input.

DVD Audio Inputs: Connect these jacks tothe analog audio jacks on a DVD or other audioor video source.

CD Inputs: Connect these jacks to the analog output of a compact disc player or CDchanger or any other audio source.

Video 1 Audio Outputs: Connect thesejacks to the RECORD/INPUT audio jacks on a VCR or any other Audio recorder.

Digital Media Player (DMP)Connector: With the AVR 240 turned off, con-nect one end of the optional Harman Kardon

to this proprietary connector, and theother to your compatible Apple iPod. When theDigital Media Player source is selected, you mayview your iPods control and navigation mes-sages on your video display (if one is connectedto one of the Video Monitor Outputs ), andin the Upper and Lower Display Lines .You may navigate the iPod and select tracks forplayback using the /// ButtonsDE, the Set Button F andTransport Controls P on your AVR remote.See page 36 for more information.

8 REAR PANEL CONNECTIONS

Rear Panel Connections

8-Channel Direct Inputs: These jacks areused for connection to source devices such asDVD-Audio or SACD players with discrete analogoutputs. Depending on the source device in use,all eight jacks may be used, though in manycases only connections to the front left/right,center, surround left/right and LFE (subwooferinput) jacks will be used for standard 5.1 audiosignals.

Digital Audio Outputs: Connect thesejacks to the matching digital input connector ona digital recorder such as a CD-R or MiniDiscrecorder.

Video Monitor Outputs: Connect this jackto the composite and/or S-Video input of a TVmonitor or video projector to view the on-screenmenus and the output of any standard Video orS-Video source selected by the receivers videoswitcher.

DVD Video Inputs: Connect these jacks tothe composite or S-Video output jacks on a DVDplayer or other video source.

Front Speaker Outputs: Connect theseoutputs to the matching + or terminals onyour left and right speakers. In conformance withthe new CEA color code specification, the Whiteterminal is the positive, or "+" terminal thatshould be connected to the red (+) terminal onFront Left speaker with the older color coding,while the Red terminal is the positive, or "+"terminal that should be connected to the red (+)terminal on Front Right speaker. Connect theblack () terminals on the AVR to the black ()terminals on the speakers. See page 12 for moreinformation on speaker polarity.

Center Speaker Outputs: Connect theseoutputs to the matching + and terminals onyour center channel speaker. In conformancewith the new CEA color code specification, theGreen Terminal is the positive, or "+" terminalthat should be connected to the red (+) terminalon speakers with the older color coding. Connectthe black () terminal on the AVR to the blacknegative () terminal on your speaker. (See page12 for more information on speaker polarity.)

Surround Speaker Outputs: Connectthese outputs to the matching + and terminalson your surround channel speakers. In confor-mance with the new CEA color code specifica-tion, the Blue terminal is the positive, or "+"terminal that should be connected to the red (+)terminal on the Surround Left speaker with oldercolor coding, while the Gray terminal should beconnected to the red (+) terminal on theSurround Right speaker with the older colorcoding. Connect the black () terminal on theAVR to the matching black negative () terminals for each surround speaker. (See page12 for more information on speaker polarity.)

Switched AC Accessory Outlet: Thisoutlet may be used to power any device that youwish to have turn on when the AVR is turned onwith the System Power Control switch 2.

Unswitched AC Accessory Outlet: Thisoutlet may be used to power any AC device. Thepower will remain on at this outlet regardless ofwhether the AVR is on or off (in Standby), pro-vided that the Main Power switch 1 is on.

Note: The total power consumption of alldevices connected to the accessory outletsshould not exceed 100 watts from theUnswitched Outlet and 50 W from theSwitched Outlet .

AC Power Cord: Connect the AC plug to anunswitched AC wall output.

Video 2 Component Video Inputs:Connect the Y/Pr/Pb component video outputs ofan HDTV Set-top convertor, satellite receiver, orother video source device with component videooutputs to these jacks.

Monitor Component Video Outputs:Connect these outputs to the component videoinputs of a video projector or monitor. When asource connected to one of the twoComponent Video Inputs is selectedthe signal will be sent to these jacks.

Video 1 Component Video Inputs:Connect the Y/Pr/Pb component video outputs ofa DVD player to these jacks.

Note: All component inputs/outputs can beused for RGB signals too, in the same way asdescribed for the Y/Pr/Pb signals, then connectedto the jacks with the corresponding color.RGB connection is not possible if the source out-puts a separate sync signal (see page 13).

Video 2 Audio Inputs: Connect these jacksto the PLAY/OUT audio jacks on a second VCRor other audio or video source.

Coaxial Digital Inputs: Connect the coaxdigital output from a DVD player, HDTV receiver,the output of a compatible computer sound cardplaying MP3 files or streams, LD player, MDplayer or CD player to these jacks. The signalmay be either a Dolby Digital signal, DTS signal,a 2 channel MPEG 1 signal, or a standard PCMdigital source. Do not connect the RF digital out-put of an LD player to these jacks.

Surround Back Speaker Outputs: Thesespeaker terminals are used to power thesurround back left/surround back right speakersin a 7.1 channel system. In normal surroundsystem use, the brown and black terminals arethe surround back left channel positive (+) andnegative () connections and the tan and blackterminals are the surround back right positive(+) and negative () terminals.

Video 1 Video Outputs: Connect thesejacks to the RECORD/INPUT composite or S-Video jack on a VCR.

Video 1 Video Inputs: Connect these jacksto the PLAY/OUT composite or S-Video jacks ona VCR or other video source.

Optical Digital Inputs: Connect the optical digital output from a DVD player, HDTVreceiver, the output of a compatible computersound card playing MP3 files or streams, LDplayer, MD player or CD player to these jacks.The signal may be either a Dolby Digital signal, aDTS signal, a 2 channel MPEG 1 signal, or astandard PCM digital source.

Video 1 Audio Inputs: Connect these jacksto the PLAY/OUT audio jacks on a VCR or otheraudio or video source.

Video 2 Video Inputs: Connect these jacksto the PLAY/OUT composite or S-Video jacks ona second VCR or other video source.

NOTE ON VIDEO CONNECTIONS: When con-necting a video source product such as a VCR,DVD player, satellite receiver, cable set-top box,personal video recorder or video game to theAVR 240, you may use either a composite or S-video connection, but not both.

Remote IR Output: This connection per-mits the IR sensor in the receiver to serve otherremote controlled devices. Connect this jack tothe IR IN jack on Harman Kardon or othercompatible equipment.

! Remote IR Input: If the AVRs front-panelIR sensor is blocked due to cabinet doors orother obstructions, an external IR sensor maybe used. Connect the output of the sensor tothis jack.

" Preamp Outputs: Connect these jacks toan optional, external power amplifier for appli-cations where higher power is desired.

# Video 2 Video Outputs: Connect thesejacks to the RECORD/INPUT composite or S-Video jacks on a second VCR.

$ Video 3 Video Inputs: Connect these jacksto the PLAY/OUT composite or S-Video jacks onany video source.

% Video 3 Audio Inputs: Connect these jacksto the PLAY/OUT audio jacks on any audio orvideo source.

& Video 2 Audio Outputs: Connect thesejacks to the RECORD/INPUT audio jacks on aVCR or any Audio recorder.

0123456789ABCDEFGHIJKLMNOPQ

MAIN REMOTE CONTROL FUNCTIONS 9

Main Remote Control Functions

Power Off ButtonIR Transmitter WindowProgram IndicatorPower On ButtonInput SelectorsAVR SelectorAM/FM Tuner Select6-Channel/8-Channel Direct InputTest ButtonSleep ButtonSurround Mode SelectorNight ModeChannel Select Button / Buttons ButtonSet ButtonDigital SelectNumeric KeysTuner ModeDirect ButtonTuning Up/DownOSD ButtonDolby Mode Select ButtonDTS Digital Mode SelectorLogic 7 Mode Select ButtonTransport ControlsSpare ButtonSkip Up/Down ButtonsStereo Mode Select ButtonDTS Neo:6 Mode SelectMacro ButtonsRDS Selector ButtonPreset Up/DownClear ButtonMemory ButtonDelay/Prev. Ch. ButtonSpeaker SelectMuteVolume Up/Down

DMP SelectorTV/Video SelectorDim Button

NOTE: The function names shown here are eachbuttons feature when used with the AVR. Mostbuttons have additional functions when usedwith other devices. See page 44-45 for a list ofthese functions.

10 MAIN REMOTE CONTROL FUNCTIONS

Main Remote Control Functions

IMPORTANT NOTE: The AVR 240s remote maybe programmed to control up to seven devices,including the AVR. Before using the remote, it isimportant to remember to press the InputSelector button 4 that corresponds to the unityou wish to operate. In addition, the AVRs remoteis shipped from the factory to operate the AVR andmost Harman Kardon CD or DVD players and cas-sette decks. The remote is also capable of operat-ing a wide variety of other products using thecontrol codes that are part of the remote. Beforeusing the remote with other products, follow theinstructions on pages 41-43 to program the prop-er codes for the products in your system.

It is also important to remember that many of thebuttons on the remote take on different functions, depending on the product selectedusing the Input Selector Button 4. Thedescriptions shown here primarily detail the func-tions of the remote when it is used to operate theAVR. (See page 44 for information about alter-nate functions for the remotes buttons.)

0 Power Off Button: Press this button toplace the AVR or a selected device unit in theStandby mode.

1 IR Transmitter Window: Point this windowtowards the AVR when pressing buttons on theremote to make certain that infrared commands areproperly received.

2 Program Indicator: This three-color indica-tor is used to guide you through the process ofprogramming the remote. (See page 41 for infor-mation on programming the remote.)

3 Power On Button: Press this button to turnon the power to a device selected by pressing oneof the Input Selectors 4 (except Tape).

4 Input Selectors: Pressing one of these but-tons will perform three actions at the same time.First, if the AVR is not turned on, this will powerup the unit. Next, it will select the source shownon the button as the input to the AVR. Finally, itwill change the remote control so that it controlsthe device selected. After pressing one of thesebuttons you must press the AVR Selector button 5 again to operate the AVRs functionswith the remote.

5 AVR Selector: Pressing this button willswitch the remote so that it will operate the AVRsfunctions. If the AVR is in the Standby mode, it willalso turn the AVR on.

6 AM/FM Tuner Select: Press this button toselect the AVRs tuner as the listening choice.Pressing this button when the tuner is in use willselect between the AM and FM bands.

7 6-Channel/8 Channel Direct Input:Press this button to select the device connected tothe 6-Channel Direct Inputs or the 8-Channel Direct Inputs (the input available will depend on the selection 5.1 or6.1/7.1 made in the surround mode setting,see page 32 for more information).

8 Test Tone: Press this button to begin thesequence used to calibrate the AVRs output levels.(See page 22 for more information on calibratingthe AVR).

9 Sleep Button: Press this button to place theunit in the Sleep mode. After the time shown inthe display, the AVR will automatically go into theStandby mode. Each press of the button changesthe time until turn-off in the following order:

Hold the button pressed for two seconds to turnoff the Sleep mode setting.Note that this button is also used to changechannels on your TV, VCR and Sat receiver whenthe appropriate source is selected, using thedevice Input Selectors 4.

A Surround Mode Selector: Press this but-ton to select any of the HALL, THEATER or VMAxsurround modes. Note that depending on thetype of input, some modes are not always avail-able. (See page 30 for more information aboutsurround modes.) Note that this button is alsoused to tune channels on your TV, VCR and Satreceiver when the appropriate source is selectedusing the device Input Selector 4.

B Night Mode: Press this button to activatethe Night mode. This mode is available only withDolby Digital encoded sources, and it preservesdialog (center channel) intelligibilty at low vol-ume levels (See page 19 for more information).

C Channel Select Button: This button isused to start the process of setting the AVRsoutput levels with an external source. Once thisbutton is pressed, use the / buttons D toselect the channel being adjusted, then press theSet button F, followed by the / buttonsD again, to change the level setting.(See page 35 for more information.)

D / Buttons: These multipurpose buttonsare used to change or scroll through items in theon-screen menus or on the front panel or tomake configuration settings such as digital inputsor delay timing. When changing a setting, firstpress the button for the function or setting to bechanged (e.g., press the Digital Select ButtonG to change a digital input) and then pressone of these buttons to scroll through the list ofoptions or to increase or decrease a setting. Thesections in this manual describing the individualfeatures and functions contain specific informa-tion on using these buttons for each application.

When the AVR remote is being programmed forthe codes of another device, these buttons are alsoused in the Auto Search process (See page 41for more information on programming the remote.)

E Button: This button is used to change themenu selection or setting during some of thesetup procedures for the AVR.

F Set Button: This button is used to enter settings into the AVRs memory. It is also used inthe setup procedures for delay time, speaker con-figuration and channel output level adjustment.

G Digital Select: Press this button to assignone of the digital inputs * to a source.(See page 34 for more information on using digital inputs.)

H Numeric Keys: These buttons serve as aten-button numeric keypad to enter tuner presetpositions. They are also used to select channelnumbers when TV, VCR or Sat receiver has beenselected on the remote, or to select track num-bers on a CD, DVD or LD player, depending onhow the remote has been programmed.

I Tuner Mode: Press this button when thetuner is in use to select between automatictuning and manual tuning. When the button ispressed so MANUAL appears in the MainInformation Display , pressing the Tuningbuttons K) will move the frequency up ordown in single-step increments. When the FMband is in use and AUTO appears in the MainInformation Display , pressing this buttonwill change to monaural reception making evenweek stations audible. (See page 39 for moreinformation.)

J Direct Button: Press this button when thetuner is in use to start the sequence for directentry of a stations frequency. After pressing thebutton simply press the proper Numeric KeysH to select a station (See page 39 for moreinformation on the tuner).

K Tuning Up/Down: When the tuner is in use,these buttons will tune up or down through theselected frequency band. If the Tuner Mode but-ton I has been pressed or the Band button !on the front panel was held pressed so thatAUTO appears in the Main InformationDisplay , pressing either of the buttons willcause the tuner to seek the next station withacceptable signal strength for quality reception.When the MANUAL appears in the MainInformation Display , pressing these but-tons will tune stations in single-step increments.(See page 39 for more information.)

L OSD Button: Press this button to activatethe On Screen Display (OSD) system used to setup or adjust the AVRs parameters.

MAIN REMOTE CONTROL FUNCTIONS 11

M Dolby Mode Selector: This button is usedto select one of the available Dolby Surround processing modes. Each press of this button willselect one of the Dolby Pro Logic II modes, Dolby3 Stereo or Dolby Digital. Note that the DolbyDigital mode is only available with a digital inputselected and the other modes only as long as aDolby Digital source is not playing (except ProLogic II with Dolby Digital 2.0 recordings, seepage 31). See page 30 for the available Dolby sur-round mode options.

N DTS Digital Mode Selector: When a DTSsource is in use the AVR will select the appropri-ate mode automatically and no other mode willbe available. Pressing this button will display themode currently selected by the AVRs decoder,depending on the surround material played andthe speaker setting. When a DTS source is not inuse, this button has no function. (See page 30 forthe available DTS options.)

O Logic 7 Selector: Press this button to selectone of the available Logic 7 surround modes. (Seepage 30 for the available Logic 7 options.)

P Transport Control Buttons: These buttonsdo not have any functions for the AVR, but theymay be programmed for the forward/reverse playoperation of a wide variety of CD or DVD players,and audio or video- cassette recorders. (See page40 for more information on programming theremote.)

Q Spare Button: This button has no functionwhen used with the AVR. When used with theDVD player, it controls the Subtitle On/Off func-tion.

Skip Up/Down Buttons: These buttons donot have a direct function with the AVR, butwhen used with a compatibly programmed CD orDVD player/changer they will change the trackson the disc currently being played.

Stereo Mode Selector: Press this buttonto select a stereo playback mode. When the but-ton is pressed so that SURROUNDOFFappears in the Main Information Display ,with only the Surr Off Surround ModeIndicator ( lit, the AVR will operate in abypass mode with true fully analog, two-channelleft/right stereo mode with no surround process-ing or bass management as opposed to othermodes where digital processing is used. Whenthe button is pressed so that SURROUNDOFF appears in the Main InformationDisplay , with both the DSP and Surr OffSurround Mode Indicators ( lit, you mayenjoy a two-channel presentation of the soundalong with the benefits of bass management.When the button is pressed so that 5 CHSTEREO or 7 CHSTEREO appears, thestereo signal is routed to all five speakers, ifinstalled. (See page 20 for more information onstereo playback modes).

DTS Neo:6 Mode Selector: Pressing thisselector button cycles the AVR through the various DTS Neo:6 modes, which extract a five-,six- or seven-channel surround field from two-channel program material (from PCM sourceor analog input signal). The first press selects thelast DTS Neo:6 surround mode that was in use,and each subsequent press selects the nextmode.

Macro Buttons: Press these buttons tostore or recall a Macro, which is a pre-pro-grammed sequence of commands stored in theremote. (See page 41 for more information onstoring and recalling macros).

RDS Select Button: Press this button to dis-play the various messages that are part of the RDSdata system of the AVRs tuner. (See page 40 formore information on RDS).

Preset Up/Down: When the tuner is in use,press these buttons to scroll through the stationsprogrammed into the AVRs memory. When CD orDVD is selected using the Input Selector button4, these buttons may function as SlowFwd/Rev (DVD) or +10 (CD, CDR).

Clear Button: Press this button to clearincorrect entries when using the remote to directlyenter a radio stations frequency.

Memory Button: Press this button to enter aradio station into the AVR s preset memory. Twounderline indicators will flash at the right side ofthe Main Information Display , you thenhave five seconds to enter a preset memory loca-tion using the Numeric Keys H. (See page 39for more information).

Delay/Prev Ch.: Press this button to beginthe process for setting the delay times used bythe AVR when processing surround sound. Afterpressing this button, the delay times are enteredby pressing the Set button F and then usingthe / buttons D to change the setting.Press the Set button again to complete theprocess. (See page 26 for more information).

Button: Press this button to change a set-ting or selection when configuring many of theAVRs settings.

Speaker Select: Press this button to beginthe process of configuring the AVRs BassManagement System for use with the type ofspeakers used in your system. Once the buttonhas been pressed, use the / buttons D toselect the channel you wish to set up.Press the Set Button F and then select thespeaker type (Large, Small or None) appropriatewith the speaker in use. (See page 23 for moreinformation).

Mute: Press this button to momentarilysilence the AVR or TV set being controlled,depending on which device has been selected.When the AVR remote is being programmed tooperate another device, this button is pressed withthe Input Selector button 4 to begin the pro-gramming process. (See page 41 for more infor-mation on programming the remote).

Volume Up/Down: Press these buttons toraise or lower the system volume.

Digital Media Player (DMP)Selector: When Harman Kardons (optional) is connected to DigitalMedia Player (DMP) Connector and acompatible Apple iPod is docked in ,pressing this selector will select the iPod as theaudio source input device for the AVR 240. Inaddition, if a video display is connected to one ofthe Video Monitor Outputs , the iPodsmessages will appear on screen, and in theUpper and Lower Display Lines . The/// Buttons DE, the SetButton F and the Transport Controls Pmay be used to navigate the iPod and to operatemany functions. See page 36, and the manualsfor The Bridge and your iPod for more informa-tion.

TV/Video Button: This button does nothave a direct function on the AVR, but when usedwith a compatibly programmed VCR, DVD orsatellite receiver that has a TV/Video function,pressing this button will switch between the out-put of the player or receiver and the externalvideo input to that player. Consult the OwnersManual for your specific player or receiver for thedetails of how it implements this function.

NOTE: With the press of any remote button theInput Selector button 45 associatedwith the botton pressed will briefly flash red toconfirm the transmission of the command, aslong as there is a function for that button withthe device selected (see function list on pages 44-45).

Dim Button: Press this button to activatethe Dimmer function, which reduces the bright-ness of the front-panel display, or turns it offentirely. The first press of the button shows thedefault state. Press the button again to changethe display to reduce the brightness by 50%, andpress it again within five seconds and the maindisplay will go completely dark. Note that thissetting is temporary; regardless of any changes,the display will always return to full brightnesswhen the AVR is turned on. The blue illuminationaround the Power Indicator 3 will alwaysremain at full brightness regardless of the settingto remind you that the AVR is still turned on.

Main Remote Control Functions

12 INSTALLATION AND CONNECTIONS

After unpacking the unit, and placing it on a solidsurface capable of supporting its weight, you willneed to make the connections to your audio andvideo equipment.

Audio Equipment Connections

We recommend that you use high-quality inter-connect cables when making connections tosource equipment and recorders to preserve theintegrity of the signals.

When making connections to audio sourceequipment or speakers it is always a good practice to unplug the unit from the AC wall outlet. This prevents any possibility ofaccidentally sending audio or transient signals tothe speakers that may damage them.

1. Connect the analog output of a CD player tothe CD inputs .

NOTE: When the CD player has both fixed andvariable audio outputs it is best to use the fixedoutput unless you find that the input to thereceiver is so low that the sound is noisy, or sohigh that the signal is distorted.

2. Connect the analog Play/Out jacks of a cas-sette deck, MD, CD-R or other audio recorder tothe Tape Input jacks . Connect the analogRecord/In jacks on the recorder to the TapeOutput jacks on the AVR.

3. Connect the digital output of any digitalsources such as a CD or DVD changer or player,advanced video game, a digital satellite receiver,HDTV tuner or digital cable set-top box or theoutput of a compatible computer sound card tothe Optical and Coaxial Digital Inputs*.We recommend connecting the coaxial digitalaudio output of your DVD player to the Coax 1Digital Audio Input , since that digital inputis assigned to the DVD source by default.

The Video 2/Cable/Sat source defaults to theOptical 1 Digital Audio Input . If yourcable television set-top box or satellite receiver isequipped with an optical digital audio output,we recommend that you connect it to this inputto obtain the benefits of higher-quality digitalaudio (such as PCM, Dolby Digital 2.0 or DolbyDigital 5.1 signals when broadcast by your cableor satellite provider).

4. Connect the Coaxial or Optical DigitalOutputs on the rear panel of the AVR to thematching digital input connections on a CD-R orMiniDisc recorder.

5. Assemble the AM Loop Antenna supplied withthe unit as shown below. Connect it to the AMand GND screw terminals .

6. Connect the supplied FM antenna to the FM(75 ohm) connection . The FM antenna maybe an external roof antenna, an inside poweredor wire lead antenna or a connection from acable system. Note that if the antenna or connec-tion uses 300-ohm twin-lead cable, you shoulduse a 300-ohm-to-75-ohm adapter to make theconnection.

7. With the AVR 240 turned off, connect theoptional Harman Kardon to Digital Media Player (DMP) Connector .Your compatible Apple iPod may be docked in

when you wish to use it as your audiosource device. Video materials stored on the iPodare not able to be viewed using the AVR.

8. Connect the front, center and surroundspeaker outputs to the respectivespeakers.

To assure that all the audio signals are carried toyour speakers without loss of clarity orresolution, we suggest that you use high-qualityspeaker cable. Many brands of cable areavailable and the choice of cable may be influen-ced by the distance between your speakers andthe receiver, the type of speakers you use,personal preferences and other factors. Yourdealer or installer is a valuable resource toconsult in selecting the proper cable.

Regardless of the brand of cable selected, we recommend that you use a cable constructed offine, multistrand copper with an area greater than2 mm2.

Cable with an area of 1.5 mm2 may be used forshort runs of less than 4 m. We do not recom-mend that you use cables with an area less than1mm2 due to the power loss and degradation inperformance that will occur.

Cables that are run inside walls should have theappropriate markings to indicate listing with anyappropriate testing agency standards. Questionsabout running cables inside walls should bereferred to your installer or a licensed electricianwho is familiar with the applicable local buildingcodes in your area.

When connecting wires to the speakers, be certain to observe proper polarity. Note that thepositive (+) terminal of each speaker connectionnow carries a specific color code as noted onpage 8. However, most speakers will still use ared terminal for the postive (+) connection.Connect the negative or black wire to thesame terminal on both the receiver and thespeaker.

NOTE: While most speaker manufacturersadhere to an industry convention of using blackterminals for negative and red ones for positive,some manufacturers may vary from this configu-ration. To assure proper phase and optimal per-formance, consult the identification plate on yourspeaker or the speakers manual to verify polarity.If you do not know the polarity of your speaker,ask your dealer for advice before proceeding, orconsult the speakers manufacturer.

We also recommend that the length of cableused to connect speaker pairs be identical. Forexample, use the same length piece of cable toconnect the front-left and front-right or surround-left and surround-right speakers, evenif the speakers are a different distance from theAVR.

9. Connections to a subwoofer are normallymade via a line level audio connection from theSubwoofer Output to the line-level inputof a subwoofer with a built-in amplifier. When apassive subwoofer is used, the connection firstgoes to a power amplifier, which will be connect-ed to one or more subwoofer speakers. If you areusing a powered subwoofer that does not haveline-level input connections, follow the instruc-tions furnished with the speaker for connectioninformation.

10. If an external multi-channel audio sourcewith 5.1 outputs such as an external digitalprocessor/decoder, DVD-Audio or SACD player isused, connect the outputs of that device to the 8-Channel Direct Inputs .

Video Equipment Connections

Video equipment is connected in the same manneras audio components. Again, the use of high-quality interconnect cables is recommended topreserve signal quality. To ensure best video per-formance S-Video sources should be connectedto the AVR only with their S-Video In/Outputs,not with their composite video connectors too.

1. Connect a VCRs audio and video Play/Outjacks to the Video 1 or Video 2 In jacks on the rear panel. The Audio and VideoRecord/In jacks on the VCR should be connectedto the Video 1 Out jacks on the AVR.

Installation and Connections

INSTALLATION AND CONNECTIONS 13

Installation and Connections

9. If you have a camcorder, video game or otheraudio/video device that is connected to the AVRon a temporary, rather than permanent basis,connect the audio, video and digital audio out-puts of that device to the Front Panel Inputs*. A device connected to the Video 4jacks is selected as the Video 4 input, andconnected to the digital jacks * it is selected as "Optical 3" or "Coaxial 3" input.(See page 17 for more information on inputconfiguration.)

Video Connection Notes: Y/Pr/Pb Component, RGB (see page 13), or

Composite video signals may only be viewedin their native formats and will not be convert-ed to the other formats. S-Video signals will beconverted to composite signal. The OSD can beviewed on the TV screen in any case, withVideo or S-Video input selected on the TV.

When the component video jacks are used,the on-screen menus will not be visible. Youmust switch to the standard composite or S-Video input on your TV to view those menus.

All component inputs/outputs can be used forRGB signals too, in the same way as describedfor the Y/Pr/Pb signals, then connected to thejacks with the corresponding color.But this is only correct as long as only thethree RGB video signals are output by thevideo source, with a sync signal in the "G"signal only, without any sync signal outputseparately by the source.

SCART A/V ConnectionsFor the connections described above your videodevice needs RCA (cinch) connectors or/and S-Video connectors for all Audio and Video signals:Any normal video device (Not SVHS or High 8)for only playback needs 3 RCA jacks, VCRs forrecord and playback even 6 RCA jacks. Any S-Video device (SVHS, High 8) needs 2 RCA(Audio) and 1 S-Video jack (Video), if its a play-back unit, or 4 RCA (Audio In/Out) and 2 S-Video (Video In/Out) jacks, if its a recordingVCR.

Many european video devices are equipped withRCA (Cinch) or S-Video jacks only partially, notfor all audio and video in/outputs needed asdescribed above, but with a so called Scart orEuro-AV connector (almost rectangular jack with21 pins, see drawings on next page).

In that case the following Scart to Cinchadapters or cables are needed:

Units for playback, such as satellite receivers,camcorders, DVD or LD players, need anadapter from Scart to 3 RCA plugs, see fig. 1(normal video devices) or from Scart to 2RCA+1 S-Video plugs, see fig. 4 (S-Videodevices).

HiFi VCRs need an adapter from Scart to 6RCA plugs, see fig. 2 (normal video), or fromScart to 4 Audio+2S-Video jacks, see fig. 5 (S-Video VCR). Read carefully the instructionattached to the adapter to find which of thesix plugs is used for the record signal to theVCR (connect with the AVRs Out jacks) andfor the playback signal from the VCR (connectwith the AVRs In jacks). Do not misconnectAudio and Video signals. Dont hesitate to con-sult your dealer, if you are uncertain.

If you use only normal video devices the TVmonitor needs an adapter from 3 RCA plugsto Scart (fig. 3) only. If also S-Video devices areused an adapter from 2 RCA+1S-Video plugsto Scart is needed additionally (fig. 6), con-nected to the SCART input on your TV that isprovided for S-Video.

Note that only the video plugs (the "yellow"cinch plug in fig. 3 and the S-Video plug in fig. 6) must be connected to the TV MonitorOutput , and the volume on the TV must bereduced to minimum.

Important Note for Adapter Cables:If the cinch connectors of the adapter youll useare labeled, connect the Audio and Video Inplugs with the corresponding Audio and VideoIn jacks on the AVR (and with a VCR connectthe Out plugs to the Out jacks on the VCR).Note that with some adapter types it may bejust turned around: If no signal is audible/ visiblewhen the VCR is playing connect the Outplugs to the In jacks on the AVR and turnedaround. If the adapter plugs are not labeled inthat way, pay attention to the signal flow direc-tions as shown in the diagrams above and in theinstruction attached to the adapter. If uncertain,dont hesitate to consult your dealer.

Important Notes for S-Video connections:1. Only the S-Video In/Out of S-Video devicesmust be connected to the AVR, NOT both,normal video and S-Video In/Outputs (except theTV, see item below).When both connections are made, only the S-Video signal will be viewed on the screen.

2. Like most common AV units the AVR does notconvert the Video signal to S-Video, only viceversa. Thus both connections must be made fromthe AVR to the TV if both, Video and S-Videosources, are used, and the appropriate input onthe TV must be selected.

2. Although any video device may be connectedto these jacks, we recommend connecting yourvideo recorder to the Audio 1 Audio/VideoInput Jacks so that you may take advan-tage of the fact that the remote control is pre-programmed with video recorder product codesfor the Video 1 device.For the same reason, we recommend connectingyour cable TV converter or satellite receiver tothe Video 2 Audio/Video Input Jacks ,and your television to the Video 3Audio/Video Input Jacks $% .

IMPORTANT: If you are only using the televisionas a display device (i.e., if you receive your tele-vision programs through a cable box or satellitereceiver), do not connect the TVs outputs to theVideo 3 Audio/Video and S-Video InputJacks $% , or to any other inputs on the AVR.

3. Connect the analog audio and video outputsof a DVD or laser disc player to the DVD jacks .

4. Connect the digital audio outputs of a CD,MD or DVD player, satellite receiver, cable box orHDTV converter to the appropriate Optical orCoaxial Digital Inputs *.Remember that the DVD source defaults to theCoaxial 1 Digital Input . All other sourcesdefault to their analog inputs, although anysource may be assigned to any digital audioinput on the receiver.

5. Connect the Composite and S-Video (if S-Video device is in use) Monitor Output jacks on the receiver to the composite and S-Video input of your television monitor or videoprojector.

6. If your DVD player and monitor both havecomponent video connections, connect the com-ponent outputs of the DVD player to the Video1 Component Video Inputs . Note thateven when component video connections areused the audio connections must still be madeto either the analog DVD Audio Inputs orany of the Coaxial or Optical Digital Inputjacks .

7. If another component video device is avail-able, connect it to the Video 2 ComponentVideo Input jacks . The audio connectionsfor this device should be made to either theVideo 2 Input jacks # or any of the Coaxialor Optical Digital Input jacks .

8. If the component video inputs are used,connect the Component Video Output tothe component video inputs of your TV, projectoror display device.

14 INSTALLATION AND CONNECTIONS

Installation and Connections

Figure 1:SCART/Cinch-Adapter

for playback;signal flow:

SCART Cinch

Figure 2:SCART/Cinch-Adapter

for record and playback;signal flow:

SCART Cinch

Figure 3:Cinch/SCART-Adapter for

playback;signal flow:

Cinch SCART

Figure 4:SCART/S-Video Adapter

for playback;signal flow:

SCART Cinch

Figure 5:SCART/S-Video Adapter

for record and playback;signal flow:

SCART Cinch

Figure 6:SCART/S-Video Adapter

for playback;signal flow:

Cinch SCART

Black

Yellow

Red

Black

Red

Blue1

Yellow

Green1

White

Black

Yellow

Red

Red

Black

S-Video In

Red

Black

S-Video Out

Black

Red

Blue1

Yellow

S-Video In

S-Video Out

1 Also other colours possible, e.g. brown and grey.

Important Note for the Use of SCART-Cinch Adapters:When video sources are connected to the TVdirectly with a SCART cable, specific controlsignals apart from Audio/Video signals will befed to the TV. These specific signals are: With allvideo sources, the signal for automatic inputselection that switches the TV automatically tothe appropriate input as soon as the videosource is started. And with DVD players, thesignals automatically turning the TV to 4:3/16:9format (with 16:9 TVs or with 4:3 TVs withselectable 16:9 format) and turning the RGBvideo decoder of the TV on or off, depending onthe DVD players setting. With any adapter cable,these control signals will be lost and theappropriate setting of the TV must be mademanually.

Note for RGB signal with SCART:If you use a unit providing RGB signals on aSCART output (as e.g. most DVD players do) andyou want to use that RGB signal, this SCARToutput must be connected directly to your TV.Although the AVR can switch three-way videosignals (like component signals Y/Pb/Pr), mostTVs need separate sync signals for RGB (alsowith SCART) that cannot be switched and pro-vided by the AVR.RGB signals can be pathed through the AVR onlywhen no separate sync signal is needed (see lastVideo Connection Note on page 13).

System and Power ConnectionsMain Room Remote Control ExtensionIf the receiver is placed behind a solid or smokedglass cabinet door, the obstruction may preventthe remote sensor from receiving commands. Inthis event, the remote sensor of any HarmanKardon or other compatible device, not coveredby the door, or an optional remote sensor maybe used. Connect the Remote IR Output ofthat device or the output of the remote sensor tothe Remote IR Input jack !.

If other components are also prevented fromreceiving remote commands, only one sensor isneeded. Simply use this units sensor or a remoteeye by running a connection from the RemoteIR Output jack to the Remote IR Inputjack on Harman Kardon or other compatibleequipment.

AC Power ConnectionsThis unit is equipped with two accessory ACoutlets. They may be used to power accessorydevices, but they should not be used with high-current draw equipment such as poweramplifiers. The total power draw to theUnswitched Outlet must not exceed 100 watts, that to the Switched Outlet 50 watts.

The Switched outlet will receive power onlywhen the unit is on completely. This is recom-mended for devices that have no power switchor a mechanical power switch that may be left inthe ON position.

NOTE: Many audio and video products go into aStandby mode when they are used withswitched outlets, and cannot be fully turned onusing the outlet alone without a remote controlcommand.

The Unswitched outlet will receive poweras long as the unit is plugged into a powered ACoutlet and the Main Power Switch 1 is on.

The AVR draws significantly more current thanother household devices such as computers thatuse removable power cords. For that reason, it isimportant that only the cord supplied with theunit (or a direct replacement of identical capaci-ty) be used.

Once the power cord is connected, you arealmost ready to enjoy the AVR 240s incrediblepower and fidelity!

INSTALLATION AND CONNECTIONS 15

Installation and Connections

Speaker Selection

No matter which type or brand of speakers isused, the same model or brand of speaker shouldbe used for the front-left, center and front-rightspeakers. This creates a seamless front sound-stage and eliminates the possibility of distractingsonic disturbances that occur when a soundmoves across mismatched front-channel speakers.

Speaker Placement

The placement of speakers in a multichannelhome-theater system can have a noticeableimpact on the quality of sound reproduced.

Depending on the type of center-channel speakerin use and your viewing device, place the centerspeaker either directly above or below your TV, orin the center behind a perforated front-projectionscreen.

Once the center-channel speaker is installed,position the left-front and right-front speakers sothat they are as far away from one another as thecenter-channel speaker is from the preferredlistening position. Ideally, the front-channelspeakers should be placed so that their tweetersare no more than 60cm above or below thetweeter in the center-channel speaker.

They should also be at least 0.5 meter from yourTV set unless the speakers are magneticallyshielded to avoid colourings on the TV screen.Note that most speakers are not shielded, evenwith complete surround sets only the Centerspeaker may be.

Depending on the specifics of your roomacoustics and the type of speakers in use, youmay find that imaging is improved by moving thefront-left and front-right speakers slightly forwardof the center-channel speaker. If possible, adjustall front loudspeakers so that they are aimed atear height when you are seated in the listeningposition.

Using these guidelines, youll find that it takessome experimentation to find the correct locationfor the front speakers in your particularinstallation. Dont be afraid to move thingsaround until the system sounds correct. Optimizeyour speakers so that audio transitions across thefront of the room sound smooth.

When the AVR is used in 5.1-channel operation,the preferred location for surround speakers is onthe side walls of the room, at or slightly behindthe listening position. In a 6.1-channel system, aback surround speaker is required, ideally placedat the center of the room's rear wall, pointingdirectly towards the front center channel speaker.The center of the speaker should face you (seebelow).

In a 7.1-channel system, both side surround andback surround speakers are required. The centerof the speaker should face you (see below).

Rear surround speakers are required when a full7.1-channel system is installed, and they mayalso be used in 5.1 channel mode as an alterna-tive mounting position when it is not practical toplace the main surround speakers at the sides ofthe room. Speakers may be placed on a rear wall,behind the listening position. As with the sidespeakers, the center of the rear surrounds shouldface you. The speakers should be no more than 2meters behind the rear of the seating area.

It is appropriate to configure the AVR 240 foreither 5.1- or 7.1-channel operation, but not for6.1 channels. When 6.1-channel programmaterial or a 6.1-channel processing mode is inuse, material for the surround back channel willbe outputted simultaneously through both theSurround Back Left and Right SpeakerOutputs . Connecting only one loudspeaker tothese speaker terminals will not only deprive youof the benefits of 7.1-channel surround modes,such as Logic 7, but will also interfere with thefunctioning of EzSet+ speaker setup and calibra-tion, as described on page 20. It may also putundesirable strain on the surround back amplifiercircuits and power supplies.

Subwoofers produce largely nondirectionalsound, so they may be placed almost anywhere ina room. Actual placement should be based onroom size and shape and the type of subwooferused. One method of finding the optimal locationfor a subwoofer is to begin by placing it in thefront of the room, about 15cm from a wall, ornear the front corner of the room. Anothermethod is to temporarily place the subwoofer inthe spot where you will normally sit, and thenwalk around the room until you find a spot wherethe subwoofer sounds best. Place the subwooferin that spot. You should also follow the instruc-tions of the subwoofers manufacturer, or youmay wish to experiment with the best location fora subwoofer in your listening room.

A) Front Channel Speaker Installation withDirect-View TV Sets or Rear-Screen Projectors

At least 15 cm from celling

At least 60 cm

5.1-Channel System

6.1-Channel System

7.1-Channel System

16 SYSTEM CONFIGURATION

System Configuration

Once the speakers have been placed in the roomand connected, the remaining steps are to pro-gram the system configuration memories. Withthe AVR two kind of memories are used, thoseassociated individually with the input selected,e.g. surround modes, and others working global-ly for all inputs selected like speaker output lev-els, crossover frequencies or delay times used bythe surround sound processor.

First Turn On

You are now ready to power up the AVR to beginthese final adjustments.

1. Plug the Power Cable into an unswitchedAC outlet.

2. Press the Main Power Switch 1 in until itlatches and the word OFF on the top of theswitch disappears inside the front panel. Notethat the Power Indicator 3 will turnorange, indicating that the unit is in theStandby mode.

3. Remove the protective plastic film from themain front-panel lens. If left in place, the filmmay affect the performance of your remotecontrol.

4. Install the three supplied AAA batteries in theremote as shown. Be certain to follow the (+)and () polarity indicators that are on the topof the battery compartment.

5. Turn the AVR on either by pressing the SystemPower Control 2 or the Input SourceSelector % on the front panel, or via theremote by pressing the Power On Button3, AVR Selector 5 or any of the InputSelectors 46 on the remote. The PowerIndicator 3 will turn blue to confirm that theunit is on, and the Main InformationDisplay will also light up.

NOTE: After pressing one of the Input Selectorbuttons 4 to turn the unit on, press the AVRSelector 5 to have the remote control the AVRfunctions.

Using the On-Screen Display

When making the following adjustments, youmay find them easier to make via the units on-screen display system. These easy-to-readdisplays give you a clear picture of the currentstatus of the unit and facilitate speaker, delay,input or digital selection you are making.

To view the on-screen displays, make certain youhave made a connection from the Video MonitorOut jack on the rear panel to the compositeor S-Video input of your TV or projector. In orderto view the AVRs displays, the correct video inputmust be selected on your video display. Note thatthe on-screen menus are not available when acomponent video display is in use.

IMPORTANT NOTE: When viewing the on-screenmenus using a CRT-based projector, plasma displayor any direct-view CRT monitor or television, it isimportant that they not be left on the screen for anextended period of time.As with any video display,but particularly with projectors, constant display ofa static image such as these menus or video gameimages may cause the image to be permanentlyburned into the CRT. This type of damage is notcovered by the AVR warranty and may not be cov-ered by the projector TV sets warranty.

The AVR has two on-screen display modes,Semi-OSD and Full-OSD. When making con-figuration adjustments, it is recommended thatthe Full-OSD mode be used. This will place acomplete status report or option listing on thescreen, making it easier to view the availableoptions and make the settings on the screen. TheSemi-OSD mode uses one-line displays only.

Note that when the full OSD system is in use, themenu selections are not shown in the Infor-mation Display . When the full OSD menusystem is used, OSDONwill appear in theMain Information Display to remind youthat a video display must be used.

When the semi-OSD system is used in conjunc-tion with the discrete configuration buttons, theon screen display will show a single line of textwith the current menu selection. That selectionwill also be shown in the Main InformationDisplay .

The full OSD system can always be turned on oroff by pressing the OSD button L. When thisbutton is pressed the MASTERMENU(Figure 1) will appear, and adjustments are madefrom the individual menus. Note that the menuswill remain on the screen for 20 seconds after thelatest action was made on the screen menu, thenthey will time-out and disappear from thescreen. The time-out may be increased to asmuch as 50 seconds by going to theADVANCEDSELECTmenu, and changingthe item titled FULLOSDTIMEOUT.

The semi-OSD system is also available as a sys-tem default, although it may be turned off byusing the ADVANCEDSELECTmenu. (Seepage 34). With the semi-OSD system, you maymake adjustments directly, by pressing the but-tons on the front panel or remote control for thespecific parameter to be adjusted. For example, tochange the digital input for any of the sources,press the Digital Select Button G andthen any of the Selector buttons / 7 or/ D on the front panel or remote.

Figure 1

System Setup

The AVR 240 features an advanced memory sys-tem that enables you to establish different con-figurations for the speaker configuration, digitalinput, surround mode, delay times, crossover fre-quencies and speaker setting for each inputsource. To ease the speaker setting, the samespeaker setting can also be made for all inputs.This flexibility enables you to custom tailor theway in which you listen to each source and havethe AVR memorize them. This means, for example,that you may associate different surround modesand analog or digital inputs with differentsources, or set different speaker configurationswith the resultant changes to the bass manage-ment system or the use of the center speakerand/or the Subwoofer. Once these settings aremade, they will automatically be recalledwhenever you select that input.

* * M A S T E R M E N U * *

I N P U T S E T U P

A U D I O S E T U P

S U R R O U N D S E L E C T

E z S e t +

M A N U A L S E T U P

A D V A N C E D

SYSTEM CONFIGURATION 17

However, we recommend that the first time youuse the AVR, you take advantage of the simplicityof configuring the system using the EzSet+process, which takes the guesswork out of speak-er size and delay settings, and balances thespeaker output levels to tailor the AVRs soundpresentation to your specific system and room.Before beginning the EzSet+ procedure, there area few adjustments that need to be made toensure accurate results.

The factory default settings for the AVR 240 haveall inputs configured for an analog audio inputexcept for the DVD input, where the CoaxialDigital Input is the default and the Video 2input, where the Optical Digital Audio Input is the default. Once the DSP processing systemis used for the first time for any input, the speakersettings will automatically default to Small atall positions with the subwoofer set to LFE. Thedefault setting for the surround modes is Logic 7Music, although Dolby Digital or DTS will auto-matically be selected as appropriate when asource with digital encoding is in use.

Before using the unit, you will probably want tochange the settings for most inputs so that theyare properly configured to reflect the use of digi-tal or analog inputs and the surround mode asso-ciated with the input. Remember that since theAVR memorizes the settings for each input indi-vidually, you will need to make these adjustmentsfor each input used. However, once they aremade, further adjustment is only required whensystem components are changed.

To make this process as quick and as easy as pos-sible, we suggest that you use the full-OSD sys-tem with the on-screen menus, and step througheach input.It is recommended that you record your settingsfor each input using the work-sheets in theappendix to this manual, in the event there is apower loss or if you need to reenter the settingsfor some other reason.

Input SetupThe first step in configuring the AVR is to selectan input, i.e. to associate an analog or digitalinput with each input source in use, e.g. CD orDVD. Note that once an input is selected, allsettings for the Digital Input, Speaker Configura-tion, Delay and Surround Mode will attachthemselves to that input and be stored in anonvolatile memory. This means that once made,the selection of an input will automatically recallthose settings. For that reason, the proceduresdescribed below must be repeated for each inputsource so that you have the opportunity tocustom tailor each source to your specificlistening requirements. However, once made theyneed not be changed again unless you need toalter a setting.

When using the full-OSD system to make thesetup adjustments, press the OSD button Lonce so that the MASTERMENU (Figure 1)appears. Note that the cursor will be next tothe INPUTSETUP line. Press the Set buttonF to enter the menu and the INPUTSETUPmenu (Figure 2) will appear on thescreen. Press the / buttons E until thedesired input name appears in the highlightedvideo, as well as being indicated in the frontpanel Input Indicators by the blue LED nextto the desired input name. If the input will use thestandard left/right analog inputs, no furtheradjustment is needed.

Figure 2

The AVR offers you the option of renaming eachinput (except tuner) as it appears in the on-screenand front panel messages. This is helpful if youhave more than one VCR, if you wish to associatea specific product brand name with the input, orto simply enter any name that will help you toremember which source is being selected.

To change the input name, press the /Navigation Button D on the remote so thatthe cursor is pointing to NAME. Next, pressand hold the Set Button F for a few secondsuntil a flashing box appears to the right of thecolon. Immediately release the Set Button F,as you are now ready to enter the device name.

Press the / Navigation Button D andnote that a complete set of alpha-numeric charac-ters will appear with the start of the alphabet incapital letters followed by the lower-case lettersand then numbers and symbols. When you pressthe Navigation Button D, a series of sym-bols and numbers will appear, followed by areverse list of the alphabet in lower-case letters.Press the button either way until the first letter ofthe desired name appears. If you wish to enter ablank space as the first character, press the Navigation Button .

When the desired character appears, press the Navigation Button and repeat the processfor the next letter, and continue until the desiredname is entered, up to a maximum of fourteencharacters.

Press the Set Button F to enter the inputname into the system memory and to proceedwith the configuration process.

If your system includes any sources that areequipped with Y/Pr/Pb component video outputs,the AVR is able to switch them to send the propersignals to your video display. Both ComponentVideo Inputs may be assigned to anysource for added system flexibility. The defaultsetting is for the Video 1 Component VideoInput to be assigned to the DVD, with theComponent Video 2 Jacks assigned to theother inputs. If your system does not include com-ponent video at this time, or if you do not need tochange these defaults, press the NavigationButton D to go to the next setting.

To change the Component Video assignment, firstmake certain that the cursor is pointing to theCOMPONENTIN line on the menu screen,and then press the / Navigation ButtonE until you see the desired input in thehighlighted video. The clicking noise that you willhear when the component video inputs isswitched is normal, due to the relay used toensure proper isolation between the three inputs.

When the desired component input has beenselected, press the Navigation Button Dgo to the next setting.

If you wish to associate one of the digital inputswith the selected input source, press the Button D on the remote while the INPUTSETUPmenu (Figure 2) is on the screen, andnote that the on-screen cursor will drop down tothe DIGITALIN line. Press the / ButtonsE until the name of the desired digitalinput appears. To return to the Analog input,press the buttons until the word ANALOGappears. When the correct input source appears,press the button D until the cursorappears next to BACKTOMASTERMENU,and press the Set Button F.

To associate an analog or digital input with theinput source currently selected at any time usingthe discrete function buttons, press the DigitalInput Select Button G on the front panelor the remote while the full-OSD is not in use.Within five seconds, make your input selectionusing the Selector buttons on the front panel 7or the / D Buttons on the remote untilthe desired digital or analog input is shown in theMain Information Display and in thelower third of the video display connected to theAVR. Press the Set Button F to enter the newinput assignment.

* I N P U T S E T U P *

I N P U T : D V D

N A M E :

C O M P O N E N T I N : C O M P V 1

D I G I T A L I N : C O A X I A L 1

A U T O P O L L : O F F

B A C K T O M A S T E R M E N U

System Configuration

18 SYSTEM CONFIGURATION

System Configuration

Some digital video input sources, such as a cablebox or HDTV set-top may change between ana-log and digital outputs, depending on whichchannel is in use. The AVRs Auto Polling featureallows you to avoid losing the audio feed whenthis happens by permitting both analog and digi-tal connections to the same source on the AVR.Digital audio is the default, and the unit willautomatically switch to the analog audio if thedigital audio stream stops.

In cases where only a digital source is used, youmay wish to disable the Auto Polling feature toprevent the AVR from trying to find an analogsource when the digital source is paused. To turnAuto Polling off for any input, first make certainthat the cursor is pointing to the AUTOPOLL line on the menu screen. Next, press the/ Navigation Button E so that OFFis highlighted in reverse video. Repeat the proce-dure at any time by highlighting ON to restorethe Auto Polling feature.

When DMP has been selected as thesource input, an additional line will appear in thismenu that lets you select whether you wish toallow your iPod to continue charging whiledocked in when the AVR 240 is turnedoff and placed in Standby mode. To make yourselection, press the / Buttons D until the cursor is next to the line readingRECHARGEINST-BY. Press the /Buttons E until the word YES appears ifyou wish charging to continue, and the bluelighting on The Bridge will remain lit when theAVR 240 is in Standby mode to indicate thatcharging is taking place. The default setting isNO, in which the docked iPod will not continueto charge when the AVR 240 is turned off, eventhough remains connected to the AVR.

When all needed adjustments have been made,press the Button D until the cursor isnext to BACKTOMASTERMENU to con-tinue with the system configuration.

Audio SetupThis menu allows you to configure the tone con-trols and to turn the upsampling on or off. If youdo not wish to change any of those settings atthis time, proceed to the next menu screen.However, to make configuration changes to thoseparameters, make certain that the MASTERMENU is on the screen with the cursor point-ing to the AUDIOSETUP line, and press theSet Button F. The AUDIOSETUPmenu(Figure 3) will appear.

Figure 3

The first line controls whether or not the bass/tre-ble tone controls are in the signal path. The nor-mal default is for them to be in-line, but if youwish to remove them from the circuit for flatresponse, first make certain that the cursor ispointing to the TONE line on the menu and pressthe / Navigation Button E so that OUTis highlighted in reverse video.

If you wish to leave the tone controls in the sig-nal path, the amount off boost or cut for bassand treble may be adjusted by pressing the /Navigation Button E so that the cursor isnext to the line for the setting you wish to adjust.Next, press the / Navigation Button Euntil the desired setting is shown.

Surround SetupThe next step for that input is to set the surroundmode you wish to use with that input. Since sur-round modes are a matter of personal taste, feelfree to select any mode you wish you maychange it later. The Surround Mode chart on page30 may help you select the mode best suited tothe input source selected. For example you mayselect Dolby Pro Logic II or Logic 7 for most ana-log inputs and Dolby Digital for inputs connectedto digital sources. In the case of inputs such as aCD Player, Tape Deck or Tuner, you may wish toset the mode to Stereo, if that is your preferredlistening mode for standard stereo sources, whereit is unlikely that surround encoded material willbe used. Alternatively, the 5 Channel Stereo orLogic 7 Music mode may also be a good choicefor stereo-only source material.

It is easiest to complete the surround setup usingthe full-OSD on-screen menus. From theMASTERmenu (Figure 1), press the /buttons D until the cursor is next to theSURROUNDSELECTmenu. Press the Set Button F so that the SURROUNDSELECTmenu (Figure 4) is on the screen.

Figure 4

Each of the option lines on this menu (Figure 4)selects the surround mode category, and withineach of those categories there will be a choice ofthe specific mode options. The choice of modeswill vary according to the speaker configurationin your system.

When the SURRBACK line of theSPEAKERSETUPmenu (Figure 11) is set toNONE the AVR will be configured for 5.1-channel operation, and only the modesappropriate to a five-speaker system will appear.

When the SURRBACK line of the SPEAK-ERSETUPmenu (Figure 11) is set toSMALL or LARGE the AVR will be configuredfor 6.1/7.1-channel operation, and additionalmodes such as Dolby Digital EX and 7 STEREO orLogic 7 7.1 will appear. In addition, the modesDTS ES (Discrete) and DTS+NEO:6 (DTS ESMatrix) available in the AVR 240 will not appearunless a digital source is playing the correct bit-stream.

In addition, some of the modes available in theAVR will not appear unless a digital source isselected and is playing the correct bitstream.

Remember that when you use only a single, sur-round back speaker, you will get the benefits of