hardware technical manual r manual/b1hardware_081418.pdfpair of hinges) if door is high traffic or...
TRANSCRIPT
www.pittcometals.com
ARCHITECTURAL METALS, INC.
HARDWARE
AUGUST 2018
HARDWARETECHNICAL MANUAL
www.pittcometals.com
ARCHITECTURAL METALS, INC.
HARDWARE
AUGUST 2018
HARDWARE
AUGUST 2018
HINGE HARDWARE PAGES 8 TO 9. . . . . . . . . . . . . . . . . . . . . . . . . . . .PIVOT HARDWARE PAGES 10 TO 11. . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLOSERS PAGES 14 TO 15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EXIT DEVICES PAGES 12 TO 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .HOLD OPENS PAGE 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LOCKING HARDWARE PAGES 3 TO 7. . . . . . . . . . . . . . . . . . . . . . . . . .PUSH/PULL HANDLES PAGE 2. . . . . . . . . . . . . . . . . . . . . . . . . .
www.pittcometals.com
ARCHITECTURAL METALS, INC.
HARDWARE
AUGUST 2018
INDEX
1
PULL HANDLESPull handles are 1” diameter round formed bar and are the industry standard for
contemporary Architectural design. Our offset pull comes with a 2-1/2" clearance for
enhanced ADA compliance. The pull handles are securely attached with mounting
screws through the door. Pull handle comes standard in 10” size and is optionally
available in 12” size. Pull handles can be used on doors with butt hinges, continuous
hinges, or offset pivots. Pull handles can be mounted back to back for double acting
doors.
Standard finishes available are clear, dark bronze, and black anodize. Additional
colors are optionally available.
PUSH BARSPush bars are 1” diameter round formed bar and are the industry standard for
contemporary Architectural design. Push bars are securely attached with cone head
mounting screws and a set screw at each end. Push bars are available for 3'-0” and
3-6” door sizes. Push bars can be used on doors with butt hinges, continuous hinges,
or offset pivots. Push bars can be mounted back to back for double acting doors.
Standard finishes available are clear, dark bronze, and black anodize. Additional
colors are optionally available.
PUSH/PULL BARSPush/pulls are type 31 pull handles and type 31 push bar used together on single
acting doors.
www.pittcometals.com
ARCHITECTURAL METALS, INC.
HARDWARE
AUGUST 2018
HARDWARE
AUGUST 2018
PUSH/PULL
2
STANDARD DEADLOCKStandard deadlock is made from steel with corrosion-resistant plating and comes in a
natural finish. The bolt is designed from materials to prevent break-in by sawing and
the hook provides a secure short throw. The deadlock has a 1 1/8” cylinder backset
and accepts standard 1 5/32” diameter mortise cylinders or thumbturns from either
side. See cylinder types for standard options. The deadlock housing is concealed with
an aluminum face plate finished to match the door. The bolt latches into a stainless
steel strike, with dust box, and steel backer plate.
OPTIONAL DEADLOCKOptional deadlock is made from steel with corrosion-resistant plating and comes in a
natural finish. The bolt is designed from materials to prevent break-in by sawing and
the bolt has a 1 3/8” throw. The deadlock has a 1 1/2” cylinder backset and accepts
standard 1 5/32” diameter mortise cylinders or thumbturns from either side. See
cylinder types for standard options. The deadlock housing is concealed with an
aluminum face plate finished to match the door. The bolt latches into a stainless steel
strike, with dust box, and steel backer plate. The optional deadlock is for use in
medium and wide stiles only.
FACE PLATES FOR DEADLOCK & COMBINATION LOCKExtruded aluminum face plates are finished to match door and are made to conceal
standard deadlock, optional deadlock, and combination locks. Face plates come in two
shapes. One face plate has radius to match locks installed in meeting stiles and one
has bevel to match beveled stiles.
Standard finishes are clear, dark bronze, and black anodize.
COMBINATION LOCKSStandard combination lock is made from steel with corrosion-resistant plating and
comes in a natural finish. The latch bolt has smooth quiet action and the handed latch
is reversible. The latch bolt can be fully retracted to allow door to free to swing. The
lock bolt is designed from materials to prevent break-in by sawing and prybars. The
combination lock has a 1 1/8” cylinder backset and accepts standard 1 5/32” diameter
mortise cylinders or thumbturns from either side. See cylinder types for standard
options. The deadlock housing is concealed with an aluminum face plate finished to
match the door. The bolt latches into a stainless steel strike, with dust box, and steel
backer plate.
www.pittcometals.com
ARCHITECTURAL METALS, INC.
HARDWARE
AUGUST 2018
LOCKING HARDWARE
3
OPTIONAL COMBINATION LOCKOptional combination lock has the same features as the combination lock except that
the lock has a 1 1/2” cylinder backset. The optional combination lock can only be used
on medium and wide stile doors.
Strike plates are stainless steel and come in two shapes, flat to be used on frames,
and curved for use on meeting stiles. Each strike plate comes with a dust box and a
steel backer plate for secure attachment with screws to frames or stiles. Strike plates
are to be used with deadlocks and combination locks.
STRIKE PLATES
Standard deadlatch is made from steel with corrosion-resistant plating and comes in a
natural finish. The auxiliary bolt is designed to prevent case-knife entry but the
deadlatch hardware is not as secure and deadbolt or combination lock. The deadlatch
has a 1 1/8” cylinder backset and accepts standard 1 5/32” diameter mortise cylinders
or thumbturns from either side. See cylinder types for standard options. The
deadlatch housing is concealed with an aluminum face plate finished to match the
door. The latch bolt is spring loaded and retracts with turn of key or operating handle.
The latch bolt latches into a stainless steel strike, with dust box, and steel backer
plate.
DEADLATCH
The optional deadlatch is identical to the deadlatch except the backset for the cylinder
is 1 1/2”.
OPTIONAL DEADLATCH
www.pittcometals.com
ARCHITECTURAL METALS, INC.
HARDWARE
AUGUST 2018
HARDWARE
AUGUST 2018
LOCKING HARDWARE
4
STRIKE PLATES FOR DEADLATCHStrike plates are stainless steel and come in two shapes, flat to be used on frames,
and curved for use on meeting stiles. Each strike plate comes with a dust box and a
steel backer plate for secure attachment with screws to frames or stiles. Strike plates
are to be used with deadlatch hardware.
FACE PLATES FOR DEADLATCHExtruded aluminum face plates are finished to match door and are made to conceal
standard deadlock, optional deadlock, and combination locks. Face plates come in two
shapes. One face plate has radius to match locks installed in meeting stiles and one
has bevel to match beveled stiles.
Standard finishes are clear, dark bronze, and black anodize.
ELECTRIC STRIKE FOR SINGLE DOORSElectric strike bolt retainer jaw is made of stainless steel and works with deadlatch or
cylinder latches. Strike can be controlled remotely, works with 24 volt AC current, and
is UL listed. Strike is attached to door jamb and can be field coverted to from
fail-secure (locked when unpowered) to fail-safe (locked when powered).
Standard finishes are clear, dark bronze, and black anodize.
ELECTRIC STRIKE FOR PAIR OF DOORSElectric strike is the same as electric strike for single doors except that strike is
attached to door meeting stile.
www.pittcometals.com
ARCHITECTURAL METALS, INC.
HARDWARE
AUGUST 2018
LOCKING HARDWARE
5
LONG LEVER HANDLE WITH CAM PLUGLong lever handles and cam plug work with deadlatch and combination lock to allow
key access from the exterior and handle access from the interior. Deactivation of the
deadlatch or combination lock allows access from both exterior and interior. The
handle is design to fit in slim narrow stile doors, is comfortable to the hand allowing
safe operation, and is activated with a natural downward motion. The long lever
handle can be used for handicap applications.
Standard finishes are clear and dark bronze anodize.
LATCH PADDLE DEVICEThe latch paddle device is designed to work with deadlatch and combination lock to
allow key access from the exterior and handle access from the interior. Deactivation
of the deadlatch or combination lock allows access from both exterior and interior.
The latch paddle is design to open with a natural pushing motion and can be used for
handicap applications.
Standard finishes are clear and dark bronze anodize.
MORTISE TYPE CYLINDERMortise type cylinder is a 1 5/32” diameter and 5 pin tumbler security. Cylinder is design to work withdeadlock, combination lock, and deadlatch hardware. Cylinder is design for exterior key operation, comeswith 2 keys standard, and multiple doors can be keyed alike.
Standard finishes are clear and dark bronze anodize.
EURO LATCH PADDLE DEVICE
4550 LEVER
www.pittcometals.com
ARCHITECTURAL METALS, INC.
HARDWARE
AUGUST 2018
HARDWARE
AUGUST 2018
LOCKING HARDWARE
6
THUMBTURN CYLINDERThumbturn mortise type cylinder is a 1 5/32” diameter and 5 pin tumbler security.
Cylinder is design to work with deadlock, combination lock, and deadlatch hardware.
Cylinder is design for interior keyless operation.
Standard finishes are clear and dark bronze anodize.
DUMMY CYLINDERDummy mortise type cylinder is a 1 5/32” diameter. Cylinder is design to work fill
unwanted hole and works with deadlock, combination lock, and deadlatch hardware.
Standard finishes are clear and dark bronze anodize.
The cylinder guard is a defense system against break in attempts by removing the
cylinder and then operating the latch or lock hardware through the cylinder hole. The
security ring and retainer ring are made from hardened steel. The retainer ring
permits the security ring to swivel so that cylinder can't be unscrewed from the latch
and lock hardware.
Standard finishes are clear, dark bronze, and black anodize.
CYLINDER GUARD
The exit indicator provides notification that the exit door is either locked or open. The
exit indicator can be used with deadlock or combination lock hardware. The exit
indicator can be used on medium or wide stile doors.
Standard finishes are clear, dark bronze, and black anodize.
EXIT INDICATOR
www.pittcometals.com
ARCHITECTURAL METALS, INC.
HARDWARE
AUGUST 2018
LOCKING HARDWARE
7
The butt hinge is a commercial quality stainless steel hinge. The hinge is 4 1/2” x 4” x
0.134” thick, has five knuckles, comes with two ball bearings, a non-removable pin,
and pin button. Hinge has round corners, is mortised into the door and frame, and is
attached to door/frame with thick steel tapping plates for a secure connection. Doors
come standard with one pair of hinges, but 1 1/2 pair are used if door is high traffic or
taller than 7'-6”.
Standard finishes are clear, dark bronze, and black anodize.
BUTT HINGE
Butt hinges are secured to the stile and frame with concealed zinc plated steel tapping
plates. Plates are offset so that hinges are flush to stiles and jambs. Doors come
standard with 4 tapping plates (for one pair of hinges), and 6 tapping plates (for 1 1/2
pair of hinges) if door is high traffic or taller than 7'-6”.
BUTT HINGE TAPPING PLATE
The butt hinge is a commercial quality stainless steel hinge. The hinge is 4 1/2” x 4
1/2” x 0.180” thick, has five knuckles, comes with two ball bearings, a non-removable
pin, and pin button. Hinge has round corners, is mortised into the door and frame,
and is attached to door/frame with thick steel tapping plates for a secure connection.
Monumental doors come standard with one pair of hinges, but 1 1/2 pair are used if
door is high traffic or taller than 7'-6”.
Standard finishes are clear, dark bronze, and black anodize.
OPTIONAL BUTT HINGE
Optional butt hinges are secured to the stile and frame with concealed zinc plated steel
tapping plates. Plates are offset so that hinges are flush to stiles and jambs. Doors
come standard with 4 tapping plates (for one pair of hinges), and 6 tapping plates (for
1 1/2 pair of hinges) if door is high traffic or taller than 7'-6”.
OPTIONAL BUTT HINGE TAPPING PLATE
Extension flush bolt with lever to secure the inactive leaf of a pair. Convex face allows
for flush mounting in the nose of the door stile. Top and bottom flushbolts used with a
deadlatch or pivoting deadbolt provides 3 point locking for pairs of doors. Uses 10"
long hardened steel rod with nylon tip and
7
8
" throw. Available in painted finishes to
match standard anodized finishes.
FLUSHBOLTS
www.pittcometals.com
ARCHITECTURAL METALS, INC.
HARDWARE
AUGUST 2018
HARDWARE
AUGUST 2018
HINGE HARDWARE
8
CONTINUOUS HINGE - FOR 7'-0" DOORThe continuous hinge is an aluminum geared hinge that runs full height of a 7'-0” door
stile minus 1/8” at top and threshold clearance at the bottom. The weight of the door
bears on molded bearings evenly spaced along the length of the hinge. The hinge is
optionally used when doors are in high traffic areas and/or when the weight of the
door is high. Hinge is fastened to the door and frame with fasteners staggered at 6”
on center for the length.
Standard finishes are clear, dark bronze, and black anodize.
Same as continuous hinge for 7'-0” door except this hinge is for an 8'-0” door.
CONTINUOUS HINGE - FOR 8'-0" DOOR
Same as continuous hinge for 7'-0” door except this hinge is for an 10'-0” door.
CONTINUOUS HINGE - FOR 10'-0" DOOR
CONTINUOUS STAINLESS STEEL HINGE - FOR 7'-0" DOORThe continuous stainless steel hinge is made of 14 gauge 304 series stainless steel and
is continuously interlocked with knuckles to pivot around a continuous pin for the full
height of a 7'-0” door stile (minus 1/8” at top and threshold clearance at the bottom).
The weight of the door bears on molded bearings evenly spaced along the length of
the hinge. The hinge is optionally used when doors are in high traffic or high abuse
areas. The hinge supports high weight doors up to 600 pounds. Hinge is fastened to
the door and frame with fasteners staggered at 6” on center for the length.
Standard finish is polished.
Same as continuous stainless steel hinge for 7'-0” door except this hinge is for an
8'-0” door.
CONTINUOUS STAINLESS STEEL HINGE - FOR 8'-0" DOOR
www.pittcometals.com
ARCHITECTURAL METALS, INC.
HARDWARE
AUGUST 2018
HINGE HARDWARE
9
TOP OFFSET PIVOTTop offset pivot frame and door base are made of cast aluminum. Door base has a
spring loaded stainless steel pivot pin for easy installation and is fastened to the door
with fasteners into tapped threaded holes in pivot door base. Frame base has self
lubricating bearing and is fastened to the frame with fasteners into tapped threaded
holes in frame pivot base.
Standard finishes are clear, dark bronze, and black anodize.
BOTTOM OFFSET PIVOTBottom offset pivot frame and door base are made of cast aluminum. Door pivot base
has a self lubricating bearing and is fastened to the door with fasteners into tapped
threaded holes in door pivot base. Frame pivot base has a bearing pin that has a
threaded elevation adjustment which can be locked with an allen head set screw. The
frame pivot base is fastened to the door jamb with fasteners into tapped threaded
holes in pivot base and to the surrounding construction at the sill.
Standard finishes are clear, dark bronze, and black anodize.
INTERMEDIATE OFFSET PIVOTIntermediate offset pivot frame and door base are made of cast aluminum. Door base
has a self lubricating bearing and is fastened to the door with fasteners into tapped
threaded holes in pivot door base. Frame pivot base has stainless steel pin with
concealed vertical adjustment. Frame pivot base is fastened to the frame with
fasteners into tapped threaded holes in frame pivot base. Pivot meets ANSI 156.4
grade 1 certification.
Standard finishes are clear, dark bronze, and black anodize.
OPTIONAL OFFSET PIVOT SETOptional aluminum cast offset pivot set has 3/4” offset non-handed, full mortise top
pivot and a 3/4” offset handed, full mortise bottom pivot with 3/16” vertical
adjustment screw, and lubricated ball and socket bearing assembly. Vertical
adjustment screws are concealed by stainless steel threaded caps on top and bottom
pivots. Pivot set can support doors up to 450 pounds and meets BHMA/ANSI
C07131/3530A.
Standard finishes are clear, dark bronze, and black anodize.
www.pittcometals.com
ARCHITECTURAL METALS, INC.
HARDWARE
AUGUST 2018
HARDWARE
AUGUST 2018
PIVOT HARDWARE
10
OPTIONAL INTERMEDIATE OFFSET PIVOTIntermediate aluminum cast offset pivot has 3/4” offset, is handed, and is full mortise.
Pivot has vertical adjustment that is concealed by stainless steel threaded caps. Pivot
can be used on heavy doors and meets BHMA/ANSI C07231/3525.
Standard finishes are clear, dark bronze, and black anodize.
OPTIONAL INTERMEDIATE ELECTRICAL OFFSET PIVOTIntermediate offset pivot has 3/4” offset, is handed, and is full mortise. Pivot can be
used on heavy doors and meets BHMA/ANSI C07231/3525. Electric pivot is for power
transfer with (8) 28 gage wires. Pivot can't be split for installation.
Standard finishes are clear, dark bronze, and black anodize.
INTERMEDIATE OFFSET PIVOT TAPPING PLATEOptional intermediate pivots are secured to the stile and frame with concealed zinc
plated steel tapping plates. Plates are offset so that pivots are flush to stiles and
jambs.
www.pittcometals.com
ARCHITECTURAL METALS, INC.
HARDWARE
AUGUST 2018
PIVOT HARDWARE
11
STANDARD EXIT DEVICE-RIM TYPE FOR SINGLE DOORS 3'-0"Rim latching narrow stile model utilizes a low profile touch bar that projects less than
three inches from the face of the door. The device has a 1” hardened steel
latch bolt that engages a frame mounted stainless steel roller strike. The device is
active the full length between door stiles and mounts to the door using metal covers
and end caps. The device push bar and base shall be 6063 T-6 hardened aluminum in
anodized finishes. The device shall be capable of operation by external key cylinder
with night latch or hold back settings. The device shall be capable of disengagement
by single point, quarter turn dogging. The exit device is ANSI grade 1 and UL listed.
Standard finishes are clear, dark bronze, and black anodize.
STANDARD EXIT DEVICE-RIM TYPE FOR SINGLE 3'-6" DOORSSame as 3'-0” exit device except for 3'=6” doors.
OPT. EXIT DEVICE CONCEALED VERT. RODS PR 3'-0" DOORSExit device with concealed vertical rods utilizes a low profile touch bar that projects
less than three inches from the face of the door. The device has 3/8” steel vertical
rods operating hardened steel latch bolts that engage a jamb mounted top strike and a
spring loaded bottom engagement into the threshold. The device is active the full
length between door stiles and mounts to the door using metal covers and end caps.
The device push bar and base shall be 6063 T-6 hardened aluminum in anodized
finishes. The device shall be capable of operation by external key cylinder with night
latch or hold back settings. The device shall be capable of disengagement by single
point, quarter turn dogging. The exit device is ANSI grade 1.
Standard finishes are clear, dark bronze, and black anodize.
OPT. EXIT DEVICE CONCEALED VERT. RODS PR 3'-6" DOORSSame as 3'-0” optional exit device with vertical rods except for 3'=6” doors.
www.pittcometals.com
ARCHITECTURAL METALS, INC.
HARDWARE
AUGUST 2018
HARDWARE
AUGUST 2018
EXIT DEVICES
12
MORTISE TYPE EXIT DEVICE LATCH TYPE SINGLE DOORSMortise type exit device has low profile touch bar which engages latchbolt hardware.
The device is active the full length between door stiles and mounts to the door using
metal covers and end caps. The device push bar and base shall be extruded aluminum
in anodized finishes. The device shall be capable of operation by external key cylinder.
The device shall be capable of standard dogging with hex key or optionally with
cylinder. The exit device is ANSI grade 1.
Standard finishes are clear, dark bronze, and black anodize.
MIDPANEL EXIT DEVICE FOR 3'-0" SINGLE DOORStext
MIDPANEL EXIT DEVICE FOR 3'-6" SINGLE DOORSSame as 3'-0” midpanel exit device except for 3'-6” single doors.
RIM TYPE CYLINDERtext
www.pittcometals.com
ARCHITECTURAL METALS, INC.
HARDWARE
AUGUST 2018
EXIT DEVICES
13
OVERHEAD HOLDER/LIMIT DEVICEtext
CONCEALED OVERHEAD HOLDER/LIMIT DEVICEtext
OVERHEAD SURFACE MOUNTED CLOSEROverhead closer is a flexible and durable heavy duty closer for exterior doors to 4'-0"
wide. Closer is tested and certified under ansi a156.4 grade one. closer meets ada
requirements and is ul and cul listed. Closing power is field adjustable for a wide
range of powers and adjustable back check cushions opening swing. Closer is
adaptable to push side and pull side mounting options.
Standard finishes are clear, dark bronze, and black anodize.
OVERHEAD CONCEALED CLOSEROverhead concealed closer is a durable heavy duty closer designed to fit narrow
transoms for exterior doors to 3'-6" wide. Single acting cylinder is concealed in the
head frame and the concealed arm and track are in the door top rail. Closer is tested
and certified under ansi a156.4 grade one. Closer meets ada requirements and is ul
and cul listed. Closing power is field adjustable for a wide range of powers and
adjustable back check cushions opening swing. Closer is adaptable to push side and
pull side mounting options.
Standard finishes are clear, dark bronze, and black anodize.
www.pittcometals.com
ARCHITECTURAL METALS, INC.
HARDWARE
AUGUST 2018
HARDWARE
AUGUST 2018
HOLD OPENS
14
OPTIONAL OVERHEAD CONCEALED CLOSEROverhead concealed closer is a rack and pinnon type heavy duty closer. Closer is
aluminum construction with steel lever arms, independent adusting valves for closing,
latching, and back check. Cylinder is concealed in the head frame and the concealed
arm is in the door top rail. Closer is tested and certified under ANSI A156.4 grade
one.
Standard finishes are clear, dark bronze, and black anodize.
OPTIONAL OVERHEAD SURFACE MOUNTED CLOSEROverhead surface mounted closer is designed to provide a highly flexible door closing
system suitable for use in commercial construction. Closer is limited to 48" door
width, 96" door heights, and 250 pound door weights. Closer can adjust power, back
check intensity, sweep speed, and latch speed. Closer is tested and certified under
ANSI A156.4 grade one, UL, ULC, UL10C for positive pressure, UBC 7.2 1997, CSFM,
and M.E.A..
Standard finishes are aluminum, dark bronze, and black.
www.pittcometals.com
ARCHITECTURAL METALS, INC.
HARDWARE
AUGUST 2018
CLOSERS
15