hardware and accessory guide … · lightbox 36mm ultra thin backlit aluminum frame specifications...
TRANSCRIPT
H A R D W A R E
A N D
A C C E S S O R Y
G U I D E
We drive sales through a connected in-store experience
OUR WORK | OUR PARTNERS
17mm ALUMINUM WALL MOUNTED FRAME
22mm TAMPER RESISTANT FRAME
36mm ULTRA THIN BACKLIT ALUMINUM FRAME
50mm DOUBLE SIDED ALUMINUM FRAME
100mm SINGLE SIDED ALUMINUM FRAME
120mm DOUBLE SIDED ALUMINUM FRAME
36mm OUTDOOR FLIP FRAME
17mm PLASTIC EXTRUSIONS
FABRIC TENSION SYSTEM FOR PILLARS ACCESSORIES
LED LIGHTBOX SPECIFICATIONS
TA BLE OF CONTENTS
We drive sales through a connected in-store experience
OUR WORK | OUR PARTNERS
We drive sales through a connected in-store experience
Wall Cleat
17mm ALUMINUM WALL MOUNTED FR AME
s p e c i f i c a t i o n s
a c c e s s o r i e s
■ On wall, single sided application■ Single groove for SEG (silicone edge gasket)■ Graphic print■ Internal key line groove allows you to accurately
place screws mounting method through frame screws, wall cleat, VHB tape or slat wall adapter
Mobile Enabled SEG Grip Insert
We drive sales through a connected in-store experience
22mm TAMPER RESISTANT FR AME
s p e c i f i c a t i o n s
■ On wall application■ Single sided■ Single groove for SEG graphic print■ 22mm (0.87”) overall depth■ Internal key line groove allows you to accurately
place mounting screws where needed■ Tamper resistant cap can be added to this frame
for security against damage of fabric prints
a c c e s s o r i e s
Wall CleatMobile Enabled SEG Grip Insert
We drive sales through a connected in-store experience
LightBox
36mm ULTR A THIN BACK LIT ALUMINUM FR AME
s p e c i f i c a t i o n s
Wall Cleat Backlit - LGP
■ On wall application■ Single sided■ Single groove for SEG graphic print■ 36mm (1.44”) overall depth■ Holds light guided plate for low - profile backlit■ Requires external ballasts / power unit■ Can be used unlit■ Maximum size with Light Guided Plate 48“ x 48“
- Inquire about larger sizes■ Maximum size without light guided plate limitless■ Mounting method thru - frame - screws, VHB
tape,or wall cleat extrusion.■ Can be used without cap for edgeless
appearance, or with cap for picture frame look
a c c e s s o r i e s
Mobile Enabled SEG Grip Insert
Cap Cover System
Hanging Cable
Table Top Base Solid Back Panel
We drive sales through a connected in-store experience
s p e c i f i c a t i o n s
a c c e s s o r i e s
Magnet AdapterHanging Cable
Raised Feet
Support Bar Product HoldersSupport Bar Connector
SEG Grip InsertFlat BaseTable Top Base
50MM DOUBLE SIDED ALUMINUM FR AME
■ Free standing or suspended application■ Double sided■ Double SEG groove on each side allows you to
put block out on the inner groove if needed, or allows for some creative graphic “overlays”
■ Free standing units - 10’ lengths of extrusion, will result in a support bar and straight connector at widths greater than 10’
■ Try to keep free standing heights below 10’
■ Hanging units - max height 8 - 10’ - Will require internal cable supports with internal cable
Mobile Enabled
We drive sales through a connected in-store experience
s p e c i f i c a t i o n s
a c c e s s o r i e s
Power Adapter
with fuse
100mm SINGLE SIDED ALUMINUM FR AME
■ On wall or free standing application■ Single sided■ Double groove for SEG Graphic and diffuser■ Back groove perpendicular to frame to allow for
rigid panel (used when free standing), or “Z” clips when on wall
■ Max size free standing (edge lit ) 72” max height or width X any dimension - 10’ length s of extrusion, will result in a support bar and straight connector at widths greater than 10’ try to keep free standing heights below 10’ and less (if your frame is chosen to be 72” W)
■ Max size on wall (edge lit) 72” max height or width X any dimension
■ Max size free standing (back lit) 10’ H max x width any dimension 10’ lengths of extrusion, will result in a support bar and straight connector at widths greater than 10’ try to keep free standing heights below 10’ and less (if your frame is chosen to be 72” W)
E d g e L i g h t L E D
L a t t i c e L E D
Magnet AdapterHanging Cable
Raised Feet
Support Bar Product HoldersSupport Bar Connector
SEG Grip InsertFlat Base Mobile Enabled
LightBox
We drive sales through a connected in-store experience
E d g e L i g h t L E D
L a t t i c e L E D
s p e c i f i c a t i o n s
a c c e s s o r i e s
120mm DOUBLE SIDED ALUMINUM FR AME
■ Free standing or suspended application■ Double sided■ Double groove for SEG Graphic and diffuser
panel■ Max size free standing (edge lit) 72” max height
or width X any dimension - 10’ lengths of extrusion, will result in a support bar and straight connector at widths greater than 10’
■ Try to keep free standing heights below 10’■ Hanging units (edge lit) - 72” max height or
width X any dimension. Will require internal cable supports with internal cable trusses and there is not a real width limit.
■ Internal ballasts and power units and on/off switch or direct wire to power supply
Magnet AdapterHanging Cable
Raised Feet
Support Bar Product HoldersSupport Bar Connector
SEG Grip InsertFlat Base Mobile EnabledPower Adapter
with fuse
LightBox
We drive sales through a connected in-store experience
a c c e s s o r i e s
Magnet AdapterMobile Enabled
■ Outdoor or indoor application■ On wall application■ Single Sided■ Single SEG groove for SEG Graphic■ Internal keyline groove allows you to accurately place screws■ Mounting method thru - frame - screws, tapcon, etc. (depending on substrate you are bolting to)■ “Snap Frame” applied over top to secure SEG graphic from tampering or wind.■ Internal grip slot to tighten loose fitting graphic prints■ Multi width SEG slots to take up size variance■ 50% larger SEG used in this frame for extra holding strength for outdoor or larger size displays
s p e c i f i c a t i o n s
36mm FLIP FR AME
Cap Cover System SEG Grip Insert
We drive sales through a connected in-store experience
17mm Plastic - Inlay Straight
Magnet Adapter
Mobile Enabled
17mm PLASTIC EXTRUSIONS
FA BRIC TENSION SYSTEMS FOR WALL TREATMENTS
17mm Plastic - Straight
■ On wall application, where the edge of the frame would be hidden (example a wall-to-wall print, OR when costs is an issue for aluminum 17 mm)
■ Single sided■ Single groove for SEG (silicone edge gasket) graphic■ Internal keyline groove allows you to accurately place screws or crown
staples■ Mounting method thru - frame - screws or VHB tape■ Insert magnet on wall behind graphic print
17mm Grip Plastic - Straight
■ On wall application■ Can be used in conjunction with 17mm aluminum or 17mm plastic to finish are
as around light switches, fire alarm pulls, etc.■ On wall application, where you need to finish outside corners with edge to edge
graphics.■ Single sided■ No need for SEG edge as fabric tucks into profile■ Insert magnet on wall behind graphic print
s p e c i f i c a t i o n sa c c e s s o r i e s
SEG Grip Insert
17mm Plastic - Straight 17mm Grip Plastic - Straight
17mm Plastic - Inlay Straight
■ Inlay into received areas such as window frames■ Single sided with grove for SEG graphics■ Internal keyline grove allows you to accurately place screws or erase staples■ Mounting options - frame screws, staples or VHB tape
We drive sales through a connected in-store experience
a c c e s s o r i e s
17mm Plastic - Straight
Magnet Adapter
Mobile Enabled
17mm Plastic - Outside Corner
■ Outside corner extrusion allows for two frames to come together with virtually novisible hardware
■ For use on full wall coverings where an outside corner is present and the printneed to continue
■ For use on square column wraps (pillar wraps)■ For use with SEG graphics
Plastic Edge Corner Connector
■ Injection molded corner eliminates compound miter cutting on site■ To be used in conjunction with the 17mm plastic outside corner and 17mm
plastic - straight■ Provides seamless corner finish at top or bottom edges■ For use with SEG graphics
17mm PLASTIC EXTRUSIONS
FA BRIC TENSION SYSTEMS FOR PILLAR TREATMENTS
s p e c i f i c a t i o n s
17mm Plastic - Outside Corner Plastic Edge Corner Connector
SEG Grip Insert
17mm Plastic - Inlay Straight
■ Inlay into received areas such as window frames■ Single sided with grove for SEG graphics■ Internal keyline grove allows you to accurately place screws or erase staples■ Mounting options - frame screws, staples or VHB tape
We drive sales through a connected in-store experience
PA R T S & A C C E S S O R I E S
5 0 m m S t r a i g h t C o n n e c t o r■ Utilized to connect straight cut
portions of the 50mm frames■ Utilized whenever a support
bar is needed to hold a magnetadapter
1 0 0 m m , 1 2 0 m mS t r a i g h t C o n n e c t o r■ Utilized to connect straight cut
portions of the 100mm and120mm frames
■ Utilized whenever a supportbar is needed to hold a magnetadapter
5 0 m m C o r n e r C o n n e c t o r■ Utilized to connect miter cut
portions of the 50mm frame
1 0 0 m m , 1 2 0 m mC o r n e r C o n n e c t o r■ Utilized to connect miter cut
portions of the 50mm frame■ Additional corner support
included
1 7 m m , 2 2 m m , 3 6 m mC o r n e r C o n n e c t o r■ Utilized to connect miter cut
portions of the frame
We drive sales through a connected in-store experienceWe drive sales through a connected in-store experience
H a n g i n g C a b l e■ Internal support and cable
hanging systems designed tosupport 140lbs. of total weight.
S u p p o r t B a r■ Fastens to straight connector
for 50mm, 100mm and 120mm frames
■ To be used whenever straight connector is used to provide vertical frame support
■ Can be used solely for magnet support adaptor
M a g n e t A d a p t e r■ Used to attach accessory holders
through the fabric graphics■ Repositionable on support bar■ Used on support bar■ Double or single sided■ Fully adjustable for
50mm,100mm or 120mm frames■ Can be used behind fabric for on wall
treatments
P r o d u c t H o l d e r s■ An displays that has a magnets
adapter integrated can utilize afull suite of product holders
■ A variety of options are available
PA R T S & A C C E S S O R I E S
S u p p o r t B a r C o n n e c t o r■ Allows you to connect the
support bar to 100 and 120mmframe systems.
We drive sales through a connected in-store experience
PA R T S & A C C E S S O R I E S
T a b l e T o p B a s e■ Utilized for any small frame
sized application that with atable top application
■ Used with 50mm frames
R a i s e d F o o t■ Most popular foot■ Raises free standing frames
1.25” off the ground■ Ensures that graphics remain
clean being off the ground■ Provides clearance for electrical
and plugs (a clean, out of viewsolution)
■ Used with 50mm, 100mm or120mm frames
B a s e F o o t■ Low profile, non raised foot■ Great for tradeshow displays or
for customers who prefer thislook over the raised foot andraised foot benefits
■ Used with 50mm, 100mm or120mm frames
S E G G r i p I n s e r t■ This insert allows you to tension
fabric by hand with specialinstallation tools
■ Insert graphics that don’trequire any special SEG sewnedges
■ Insert SEG grip into any frameSEG slot
We drive sales through a connected in-store experience
L G P P a n e l L E D■ Light guided plates can only be
used in the LGP Frame■ Utilize external ballasts so there
is always a “powerbrick” withthis item
■ Allows for a low profile 36mmframe
■ Exclusive to The LookCompany
■ UL / CSA Certifed
B a c k l i t L E D■ Utilized in the 100mm and 120mm
frame and provides consistent lighting
■ See lighting section for more information
■ Exclusive to The Look Company■ UL / CSA certifed■ 4500k or 600k light temperatures
available
E d g e l i t L E D■ Utilized in the 100mm and 120mm
frame and provides consistent lighting
■ See lighting section for more information
■ Exclusive to The Look Company■ UL / CSA certifed■ 4500k or 600k light temperatures
available
PA R T S & A C C E S S O R I E S
P o w e r A d a p t e r w i t h F u s e■ Utilized in any application that
demands power (excluding the LGP frame)
■ Integrated fuse■ Integrated on/off switch■ Universal 3 prong cord socket■ Change colour and length of power
cord as desired
B a c k l i g h t i n g C o n n e c t o r C l i p s■ Utilized to attach the backlight
(lattice) to the 100mm frames■ Tool-less snap - in connection of
LED lattice to frame■ Exclusive to The Look Company
We drive sales through a connected in-store experience
PA R T S & A C C E S S O R I E S
M o b i l e E n a b l e d■ Mobile integration with fabric
elements■ Utilize NFC tags to direct
customers to a website or app■ Utilize Bluetooth beacons to
deliver content through an app (retailers app)
■ Utilize QR codes to direct customers to a weblink
W a l l A d a p t e r■ Utilized to hold the 100 mm and
LGP frame on wall■ Mount adapter to wall and sit
frame onto adapter
W a l l C l e a t■ Utilized on the 17mm and
22mm frame options to hang orassist with installation of largeframe projects
S o l i d B a c k P a n e l■ For use with the 36mm, and
100mm frame systems. [new bullet] Allows the blockout of unwanted elements from walls or surrounding areas that may show through the print
■ Eliminate shadows and discoloration incurred by backwall colours
■ Rigid back panel can be printed or left untreated as required
We drive sales through a connected in-store experience
LED LIGHTBOX SPECIFICATIONS
k e y p o i n t s
B a c k l i t - L att i c e L E D
l i g h t i n g t e m p e r a t u r e
E d g e L i g h t L E D
■ UL / CSA certified
■ LED will work with any voltage worldwide 110v to 240v
■ Fused surge protection and on/off switch
■ Capable of being direct wired
■ The type of power connector used allows for a universal power cord, allowing the customer to purchase spare or
different colours from any hardware, computer or electronics
store
■ We utilize a proprietary focal length lens opposed to
others in the industry, which produces no hot spots or
dip in light intensity along the edge of the light box
■ Cost effective premium option (more expensive than edgelit). Allows for any sized lightbox to have consistent light■ 850 lumens/sqft. typical
■ Premium light box effect
■ Specialty lens design to distribute light evenly
■ Tool-less, quick assembly
■ Designed and proprietary to The Look Company
■ UL / CSA certified
■ Lowest cost lighting option
■ Do not use on varying sized boxes side by side in the same environment as intensity will vary based on box size
■ One dimension must be 72” or less for perimeter in all scenarios
■ LED strips are factory assembled on extrusion
■ Specialty lens design to distribute light evenly
■ Designed and proprietary to The Look Company
■ UL / CSA certified
6 0 0 0 k o p t i o n
■ Produces a blue/cool light effect recommended for applications that require a bright “white” feel, used when there is a largea mount of natural light, competing showroom lights or existing showroom light boxes. The 6000k lighting option can beconsidered for bold effects and contrast of the graphic print image.
4 5 0 0 k o p t i o n
■ Produces a slightly warmer light effect that is recommended when graphics details such as skin tones are important. The 4500kprovides best-in-class colour correction capability and is a consideration for print images that need detailed colour, fine printdetails and zero wash-out.
E d g e L i g h t L E DL a t t i c e L E D
We drive sales through a connected in-store experience
OUR WORK | OUR PARTNERS
We drive sales through a connected in-store experience
OUR WORK | OUR PARTNERS
We drive sales through a connected in-store experience
OUR WORK | OUR PARTNERS
We drive sales through a connected in-store experience
OUR WORK | OUR PARTNERS
1-866-979-8326 | in fo@the lookcompany.com