har-1005 lt1 fuel injection wiring harness instructions

Download HAR-1005 LT1 Fuel Injection Wiring Harness Instructions

Post on 02-Jun-2018

215 views

Category:

Documents

1 download

Embed Size (px)

TRANSCRIPT

  • 8/10/2019 HAR-1005 LT1 Fuel Injection Wiring Harness Instructions

    1/14

    Manual P/N MAN-1005 Copyright 2014

    1

    1994 1997 GM LT1 W/ 4L60EElectronic Fuel Injection Wiring Harness

    PERFORMANCE S YSTEMS INTEGRATION 170 Oberlin Ave N Suite 13 Lakewood NJ 08701-4548Ph: 732-444-3277 Email: INFO@PSIConversion.com

    www.PSIConversion.com

    Thank you for choosing Performance Systems Integration (PSI). We offer a full line of LT1/LSX and GMOverdrive Transmission parts for your conversion needs. We have attempted to provide you with as

    accurate instructions as possible. If you have found any errors or omissions, or have comments concerningthese instructions send us an e-mail at TECHSUPPORT@PSICONVERSION.COM. Once again, thank

    you for choosing PSI!

    HAR-1005

    mailto:INFO@LT1Conversion.commailto:INFO@LT1Conversion.comhttp://www.lt1conversion.com/http://www.lt1conversion.com/http://www.lt1conversion.com/mailto:INFO@LT1Conversion.com
  • 8/10/2019 HAR-1005 LT1 Fuel Injection Wiring Harness Instructions

    2/14

  • 8/10/2019 HAR-1005 LT1 Fuel Injection Wiring Harness Instructions

    3/14

    PERFORMANCE S YSTEMS INTEGRATION

    Manual P/N MAN-1005 Copyright 20143

    3.0 PRE-INSTALLATION REQUIREMENTS

    THE FOLLOWING INFORMATION DETAILS SOME OF THE HARDWARE AND SOFTWAREREQUIREMENTS WHEN INSTALLING THIS HARNESS:

    *(SEE TABLE 2 FOR COMPATIBLE REPLACEMENT SENSOR PART NUMBERS)*

    1. All LT1 Engines will require the VATs System to be removed from the PCM. If the VATs is notremoved from the PCM the engine will NOT start. Contact PSI for removal of this function.

    2. All LT1 Engines from B-body (Caprice, Roadmaster) vehicles feature two (2) Knock Sensors. The PSIharness only uses the passenger side Knock Sensor.

    3. 92-95 LT1 Engines utilized an Ignition Coil with two connectors. This Ignition Coil must be replaced with a single connector Ignition Coil from a 96 -97. (SEE TABLE 2 FOR SENSOR PARTNUMBERS)

    4. 96-97 LT1 Engines utilized four (4) O2 Sensors ; two (2) Sensors on each side of the engine, onebefore and one after the catalytic converter. The rear O2 Sensors (after the catalytic converters) are not used with the PSI Harness. Provisions are provided for two oxygen sensors in the harness.

    5. 96-97 LT1 Engines are OBDII programmed. This harness must be used with OBDI programming,

    available through PSI.6. 96-97 LT1 Engines utilized a crank mounted sensor. This sensor is not used with the PSI Harness.7. All LT1 Engines utilized an EGR, AIR Pump, and CCP features for emissions control. This harness

    does not include these provisions. EGR, Air Pump, and CCP are not necessary for engine operation.PCM reprogramming may be necessary to avoid storing a Diagnostic Trouble Code (DTC) for absenceof emissions equipment.

    8. If any sensors are missing or damaged, PSI recommends replacements listed in Table 2. Note that thePCM listed in Table 2 must be used.

    9. If you ARE using a 4L60E transmission then you MUST have a two position brake switch. These arenecessary to allow proper function of the TCC. The brake switch should be closed (electricallyconnected) when the brakes ARE NOT being applied and open (not electrically connected) when thebrakes ARE being applied. This is the opposite of a standard brake light switch. A TCC brake switchkit is available through PSI (p/n KIT-1002), contact us to order.

    CAUTION: FAILURE TO WIRE THE TCC SWITCH CORRECTLY WILL RESULT IN ADANGEROUS SITUATION IN THE VEHICLE WHERE THE TORQUECONVERTER MAY NOT UNLOCK.

    10. If you ARE going to use a T56 transmission then you MUST use a two-position VSS.11. 92-93 LT1 Engines utilized an Optispark e xtension harness connector that was approximately 1

    long., while all other LT1 Engines utilized a connector that was approximately 2 long. Ensure that youare using the correct extension harness for your application.

    4.0 TOOLS

    Non-Standard Tools Required for Installation:1. Terminal Crimping Tool2. Wire Strippers3. Electric Drill4. 2" Hole saw (for the rubber grommet in the firewall)

  • 8/10/2019 HAR-1005 LT1 Fuel Injection Wiring Harness Instructions

    4/14

    PERFORMANCE S YSTEMS INTEGRATION

    Manual P/N MAN-1005 Copyright 20144

    5.0 ROUGH INSTALLATION/ROUTING

    This harness was designed with the intent of PCM mounting in the passenger compartment (e.g. glove box,or under dash). This fuel injection harness has two sections, the Engine Compartment Section, and the DashSection, reference Figure 1 below. Note that the Engine Compartment Section is on one side of theGrommet Seal and the Dash Section is on the other side.

    ENGINE COMPARTMENT SECTION: Includes wiring for the fuel injectors, optispark, sensors,and transmission (if applicable).

    DASH SECTION: Includes ignition feed wires, DLC Connector, Underdash Wires, PCMConnectors, Chassis Ground, and Fuse/Relay Center.

    5.1 Decide where and how the PCM and Fuse/Relay Center will be mounted. PSI wiring harnesses aredesigned to mount either under the dash or in the kick panel on the right side. They must be nofurther apart than the wiring will allow.

    5.2 A good exercise is to lay out the wire harness on the floor beside your vehicle and identify all theconnectors and wires.

    5.3 You will want to route the harness through and around open areas. Inside edges provide extraprotection from hazards and also provide places for tie wraps, clips and other support.

    5.4 Route the harness away from sharp edges, exhaust pipes, and the hood, trunk and door hinges.

    5.5 Allow enough slack in the harness at places where movement could possibly occur (body to frame,frame to engine, etc.).

    5.6 Familiarize yourself with the harness by locating each of the harness sections and by looking at theconnectors on the wire ends, reference Figure 1.

    NOTE : As with all automotive wiring, the grounding circuit is critical for proper operation. Ensure that

    there is secure grounding of the following, battery to engine, battery to chassis, engine to chassis, harness toengine, and harness to chassis.

    This harness is equipped with Ground Wiring on the front portion of the driver side cylinder head andadjacent the fuse block supplied with the harness.

    5.7 Connect a ground strap or cable (minimum of a 4 Ga. wire) from the negative battery terminal tothe chassis (frame).

    5.8 Connect a ground strap (minimum of a 4 Ga. wire) from the engine to the chassis (frame). DONOT RELY UPON THE MOTOR MOUNTS TO MAKE THIS CONNECTION.

    5.9 Connect a ground strap from the engine to the body.

  • 8/10/2019 HAR-1005 LT1 Fuel Injection Wiring Harness Instructions

    5/14

    PERFORMANCE S YSTEMS INTEGRATION

    Manual P/N MAN-1005 Copyright 20145

    Figure 1 - LT1 w/4L60E Wiring Harness

    NOTE: Routing your harness depends a great deal upon the particular make of the automobile and whatextent you want to secure and conceal the harness.

    PCM Connectors

    Underdash Wires

    DLC Connector

    Chassis Ground

    Ignition Power

    Fuse/RelayConnector

    Grommet Seal

    RH 02 Sensor

    Starter(Battery)

    KnockSensor

    Optispark

    MAP Sensor

    8

    7

    6

    5

    1 = #1 Fuel Injector2 = #2 Fuel Injector3 = #3 Fuel Injector4 = #4 Fuel Injector5 = #5 Fuel Injector6 = #6 Fuel Injector7 = #7 Fuel Injector8 = #8 Fuel Injector

    1

    2

    3

    4

    Alternator

    ECT Sensor

    Ground (Cyl.Head)

    ICM

    CoilConnector

    MAF Sensor

    LH 02 Sensor

    Trans Connector

    VSS Sensor

    IAT Sensor

    TPS Sensor

    IAC Motor

  • 8/10/2019 HAR-1005 LT1 Fuel Injection Wiring Harness Instructions

    6/14

  • 8/10/2019 HAR-1005 LT1 Fuel Injection Wiring Harness Instructions

    7/14

    PERFORMANCE S YSTEMS INTEGRATION

    Manual P/N MAN-1005 Copyright 20147

    7.0 ENGINE COMPARTMENT SECTION CONNECTIONS

    7.1 Locate the black and brown wires in the driver side group that end in a single, large ring terminaland ground them to the engine. (Commonly to the front of the driver side cylinder head on theIgnition Control Module Stud).

    7.2 Using Figure 1 and specific connections indicated in Table 3 connect the wiring as directed.

    7.3 If you are using the 4L60E transmission, route the 13-position connector to the passenger side ofthe transmission and attach it.

    7.4 If you are using a 4L60E or T56, take the connector for the Vehicle Speed Sensor (VSS) andconnect it to the Vehicle Speed Sensor on the driver side of the transmission.

    Connector Connected To Wire Colors CheckCompleted1 #1 Fuel Injector Black, Pink2 #2 Fuel Injector Lt Blue, Pink3 #3 Fuel Injector Yellow, Pink4 #4 Fuel Injector Dk Green, Pink5 #5 Fuel Injector Lt Green, Pink6 #6 Fuel Injector Red, Pink7 #7 Fuel Injector White, Pink8 #8 Fuel Injector Dk Blue, Pink9 LH 02 Sensor Tan, Purple, Black, Brown10 VSS Sensor Yellow, Purple

    11 Transmission ConnectorLt Green, Yellow, Dk Green, LtBlue, Pink, Yellow, Black, Pink,

    Red, Dk Blue, White, Tan, Brown12 Knock Sensor Dk Blue13 RH O2 Sensor Tan, White, Black, Brown14 Starter (Constant Power) Red15 ECT Sensor Yellow, Black16 Alternator Red18 MAP Sensor Black, Lt Green, Grey19 IAC Motor White, Lt Blue, Lt Green, Black20 TPS Sensor Black, Dk Blue, Grey

    22 Ignition Control Module(ICM) Pink, White, Black, Dk Green

    23 Coil Connectors (Black &Gray) Pink, Pink, Dk Green

    24Ground (Drivers Cylinder

    Head) Black, Black, Tan, Tan25 MAF Sensor Yellow, Black, Pink26 Optispark Pink, Red, Purple, Dk Green31 IAT Sensor Black, Tan

    Table 3 Engine Compartment Connection Checklist (Reference Figure 1)

  • 8/10/2019 HAR-1005 LT1 Fuel Inj