guidlines bsc elect engg final year project report writing

7/28/2019 Guidlines BSc Elect Engg Final Year Project Report Writing

1/18

i

University of Engineering & Technology, Taxila.

Department of Electrical Engineering

Project Report Format

Prepared by:

Dr. Gulistan RajaAssistant Professor

[email protected]

Approved by:

Prof. Dr. Tahir Nadeem Malik

Chairman EED

June 2011
mailto:[email protected]:[email protected]:[email protected]


2/18

ii

PROJECT TITLE (in Caps)

(HARD BINDING PAGE)

Supervisor

Name

Designation

Submitted By

Name of Project Member1 07-EE-1


DEPARTMENT OF ELECTRICAL ENGINEERINGFACULTY OF ELECTRONICS & ELECTRICAL ENGINEERING

UNIVERSITY OF ENGINEERING AND TECHNOLOGY

TAXILA.

Month Year


3/18

iii

PROJECT TITLE (in Caps)

Supervisor

NameDesignation

Submitted By



A Project Report submitted in partial fulfillment of the

requirements for the award of Bachelors Degree in

Electrical Engineering

DEPARTMENT OF ELECTRICAL ENGINEERING

FACULTY OF ELECTRONICS & ELECTRICAL ENGINEERINGUNIVERSITY OF ENGINEERING AND TECHNOLOGY

TAXILA.

Month Year


4/18

iv

Undertaking

I/We certify that project work titled enter title of your project here is my/our own work.

No portion of the work presented in this project has been submitted in support of another

award or qualification either at this institution or elsewhere. Where material has been used

from other sources it has been properly acknowledged / referred.

Signature of Student 1

Name of Student 1

Registration No. of Student 1

Signature of Student 2

Name of Student 2

Registration No. of Student 2


5/18

v

Acknowledgements

We would like to thank . guiding us in understanding the concepts

of ... We would like to thank all our teachers especially

. guiding us in solving our problems related to .. our project

supervisor ... his cooperation and support to bring this project to completion.

We would also like to thank our families and friends for their continuous encouragement and

moral support.


6/18

vi

Abstract

NOTE: Write abstract here. The font of the entire document is Times New Roman size 12,

justified except headings with double line spacing.

The length of the abstract should not exceed 1 page at maximum

This project describes the implementation of..


7/18

vii

Table of Contents

Undertaking___________________________________________________________________ iv

Acknowledgements _____________________________________________________________ v

Abstract ______________________________________________________________________ vi

Chapter 1 ________________________________________________________________ 1

Introduction___________________________________________________________________ 11 BACKGROUND ____________________________________________________________________ 1

1.1 Sub Heading1 ___________________________________________________________________ 11.2 Sub Heading2 ___________________________________________________________________ 11.3 Sub Heading3 ___________________________________________________________________ 1

2 WHAT IS ________________________________________________________________________ 1

Chapter 2 ________________________________________________________________ 2

Theory related to Project ________________________________________________________ 2

2.1 Statement ______________________________________________________________________ 22.2 Technique 1 ____________________________________________________________________ 22.3 Technique 2 ____________________________________________________________________ 22.4 Technique 3 _____________________________________________________________________

Chapter 3 ________________________________________________________________ 3

Implementation of Project _______________________________________________________33.1 MODEL AND NAMING CONVENTIONS ___________________________________________ 3

3.1.1 Heading of Name1 __________________________________________________________ 33.1.1.1 Sub Heading1 ______________________________________________________________ 3

3.1.2 Heading of Name2 __________________________________________________________ 33.1.3 Heading of Name3 __________________________________________________________ 33.1.4 Heading of Name3 __________________________________________________________ 3

Chapter 4 ________________________________________________________________ 4

Simulation Results _____________________________________________________________ 41 HEADING 1 _____________________________________________________________________ 42 HEADING 2 _____________________________________________________________________ 4

CONCLUSION ___________________________________________________________________________ 5FUTURE RECOMMENDATIONS ___________________________________________________________ 6

Appendix A _______________________________________________________________ 7

Title of Appendix ______________________________________________________________ 7

References ____________________________________________________________________ 8

Hard Copy I nf ormation _____________________________________________________ 9


8/18

viii

Listof Figures

Figure 1Class diagram ...................................................................................................................................


9/18

ix

Listof TablesTable: List of abc ...............................................................................................................................................

Table: List of xyz ..............................................................................................................................................


10/18

1

Chapter 1

Introduction

1 BACKGROUND

1.1 Sub Heading1

Text here

1.2 Sub Heading2

abc xyz

1.3 Sub Heading3

Text..

.. .. ..

2 WHAT IS

Text here

New Line

NOTE: DRAW ALL DIAGRAMS IN MS VISIO FIGURE CAPTIONS BELOW FIGURE TABLE CAPTIONS ABOVE TABLE


11/18

2

Chapter 2

Theory Related to Project

2.1 Statement

The . will be based on the ..

2.2 Technique 1

Explain Technique 1 present in literature here.

2.3 Technique 2


2.4 Technique 3



12/18

3

Chapter 3

Implementation of Project

3.1 MODEL AND NAMING CONVENTIONS

Text here..

3.1.1 Heading of Name1

Text here..

3.1.1.1Sub Heading1

Text here


Text here


Text here


Text here

3.2 HEADING

Text here


13/18

4

Chapter 4

Simulation Results

1 HEADING 1

Discuss simulation results of your project here


14/18

5

Conclusion

We started the project with the objectives mentioned in the project statement and achieved all

of them. We have implemented


15/18

6

Future Recommendations

We would like to recommend the following features to be incorporated in our developed

software ..

abc xyz


16/18

7

Appendix A

Title of Appendix

Text here

Further appendixes can be inserted in the same format


17/18

8

References

Write down references used for the proposal here. Wri te down the references in order ofpubl ication year with ol dest reference at top and latest at the bottom. Use the following

formatfor references.

Example Journal Paper:

[1]Didier Le Gall, MPEG: A video compression standard for multimedia applications,Communications ACM, vol. 34, no. 4, pp. 4658, April 1991.

Example Conference Paper:

[2]Gulistan Raja and M. J. Mirza, Performance comparison of advanced video codingH.264 standard with baseline H.263 and H.263+ standards, in Proc. 4th IEEEInternational Symposium on Communications & Information Technologies, ISCIT 04,

Sapporo, Japan, 2004, pp. 743746.

Example Book:

[3]Iain E.G. Richardson, Video Codec Design, Great Britain, John Wiley & Sons, 2003,ISBN: xx-yyyy-zzzz.

Example Web Link:[4] MPEG Software Simulation Group, The MSSG homepage, available on-line at

http://www.mpeg.org/MPEG/ MSSG, 2004.

Example Standard:

[5]ITU-T Video Coding for low bit rate communication, ITU-T Recommendation H.263;version 1, Nov 1995; version 2, Jan. 1998; version 3, Nov. 2000.
http://www.mpeg.org/MPEG/%20%20MSSGhttp://www.mpeg.org/MPEG/%20%20MSSGhttp://www.mpeg.org/MPEG/%20%20MSSG


18/18

9

Hard Copy Information

Page Size A4 (21 cm x 29. 7 cm)Page Margins Top and Bottom = 2.54 cm

Left 3.81 cm, and Right = 2.54 cm

Page orientation Portrait

Line Spacing Double

Page Numbering Bottom Left

Printing One Side per sheet

1. THREE Hard bound copies (1 for supervisor/group, 1 for library/group and 1 forstudent) of the project report are to be submitted for final project examination. Hard

bound means permanently stitched and bound in BLUE COVERwith the title of the

project and your name clearly inscribed on the cover as per format given at the first

page of template in SILVERcolor.

2. The SPINE of project report should have Authors 1st Name (in case of multipleauthors) / Authors Full Name (in case of single author) , B.Sc. Elect. Engg. and

Year of Passing ONLY. The Authors name should be in vertical orientation while

B.Sc. Elect. Engg. and year of passing. should be in horizontal orientation in the spine

of hard bound copy of project.

3. TWO CDs containing soft copy of project report (in PDF and MS WORD format) to besubmitted in the Academic Cell. Both CDs must be titled using Permanent Marker with

the Students Regd. Nos & Project Title in brief. The transparent plastic casings of CDs

must also be titled with Student Regd. Nos, Project Title, Supervisor Name & Signature.

guidlines bsc elect engg final year project report writing

Documents