gsb-280 tyre bead remover user s manual
TRANSCRIPT
Leshan Shengxing Machinery China’s Leading Manufacturer of Tyre Recycling Equipment
Tel:(English Service)+86 13981391202, E-mail: [email protected] www.tyrerecycleline.com
GSB-280 Tyre Bead Remover
User’s Manual
P.R.C Patent No. ZL 0121472.3
Leshan Shengxing Machine Co., Ltd
2010
www.tyrerecycleline.com
Leshan Shengxing Machinery China’s Leading Manufacturer of Tyre Recycling Equipment
Tel:(English Service)+86 13981391202, E-mail: [email protected] www.tyrerecycleline.com
1.Function
GSB-280 Tyre Bead Remover can Peel off the rubber attached on
the tyre beads, to separate the rubber and steel bead so they can
be recycled and reused.
GSB-280 can be used either individually to remove the beads
directly from whole waste tyres, or be used in combine with tyre
disassemblers, remove the bead from tyre side walls cut off by tyre
disassemblers.
2.Specifications
Model GSB-280
Applicable Tyre SIze
(Hoop Diameter)
12″-22″
Process capacity (strip/hour) 60
Main motor power(KW) 15
Weight(kg) About 1200
Dimension(mm) 1250X1150X1300
www.tyrerecycleline.com
Leshan Shengxing Machinery China’s Leading Manufacturer of Tyre Recycling Equipment
Tel:(English Service)+86 13981391202, E-mail: [email protected] www.tyrerecycleline.com
3.Installation and Testing
Note: The design/size/color of control panel varies on the different batch of production according
to client requirements.
1. Keep the machine and flat ground, then level the four corners.
2. The machine should be installed with grounding protection, the
Resistance should be under 4Ω
www.tyrerecycleline.com
Leshan Shengxing Machinery China’s Leading Manufacturer of Tyre Recycling Equipment
Tel:(English Service)+86 13981391202, E-mail: [email protected] www.tyrerecycleline.com
3. Hyperbolic curve gear oil must be injected into the Speed Reducer
and the Wheel Gear Box before using the machine. The oil should be
cover the gears.
4. Lubricate the main bearings of the two separation rollers with
hyperbolic curve gear oil before using. The oil should be added every
shift. (8 hours).
www.tyrerecycleline.com
Leshan Shengxing Machinery China’s Leading Manufacturer of Tyre Recycling Equipment
Tel:(English Service)+86 13981391202, E-mail: [email protected] www.tyrerecycleline.com
5. The two rollers are cooled by water, therefore cooling water should
be added before using the machine.
6. The gap between the two separation rollers is 1-3mm, the gap size
influence the working load. Add just the gap size according to the
result of bead removing , until it removes the beads smoothly and
clean.
7. Each time using the machine, check and make sure the lubricating oil
in Speed Reducer and Wheel Gear Box is enough, make sure all the
screws are tightly installed.
4. Using the machine to remove the beads
1.Press the start button to tart the Motor
2.Place the whole tyre or the tyreside wall on the hoop bracket.
www.tyrerecycleline.com
Leshan Shengxing Machinery China’s Leading Manufacturer of Tyre Recycling Equipment
Tel:(English Service)+86 13981391202, E-mail: [email protected] www.tyrerecycleline.com
3. Rotate the hand wheel to move the tyre or the sidewall inward until it is
grasped by the two separation rollers. The rollers will start removing the
beads automatically.wait until the beads are separated with the rubber
part.
4. Rotate the hand wheel to move the bracket outward, take down the
beads to finish the whole removing process.
www.tyrerecycleline.com
Leshan Shengxing Machinery China’s Leading Manufacturer of Tyre Recycling Equipment
Tel:(English Service)+86 13981391202, E-mail: [email protected] www.tyrerecycleline.com
Warning!
Don’t take out the beads directly between the rollers with hands.
www.tyrerecycleline.com