grooved quality since 1981 piping system · october 2019 fire protection piping solutions allied...

January 2019 FIRE PROTECTION PIPING SOLUTIONS

ALLIED RUBBER &GASKET [email protected]

QUALITY SINCE 1981

ARGCO reserves the rights of final interpretation and modification of this catalog. All information is subject to change without notice.

GROOVEDPIPING SYSTEM

FLEXIBLE COUPLINGSARGCO flexible couplings allow for full design features in applications such as curved or deflected layouts and or when systems are exposed to outside forces beyond normal static conditions such as seismic events or where vibra-tion and or noise attenuation are a concern. The ability to design in controlled flexibility is an advantageous feature when compared to traditional rigid joining methods such as threading, flanging and welding. When designing with flexible couplings you must allow for proper support to the system so as to eliminate undesired stress.There are several published standards and codes covering grooved piping component. These codes or standards may vary as to the definition or standard for flexible couplings. System designers should confirm which standard(s) and or code(s) are required for the system being designed and they should select the applicable coupling for the application.

RIGID OR FLEXIBLE?

Lede grooved couplings are classied into two types, exible and rigid. What are the differences? When and where should they be used? The following informa�on is intended for system designers and installers to be�er understand the nature of the grooved piping systems. This will allow the designer and installer to make be�er use of the design features and advantages of grooved piping components and systems.

Angle-pad design: As the bolts are �ghtened, the angled bolt pads slide in opposite direc�ons causing the couplings keys to �ghtly grip the pipe, while at the same �me the pipe grooves are forced outward against the coupling keys.

T&G design: The T&G (tongue & groove) mechanism provides a mechanical and fric�onal interlock resul�ng in a rigid joint which reduces undesired angular movement. Lede precision cas�ng techniques allow the coupling segments to meet metal-to-metal when installed on properly grooved pipe.

RIGID COUPLINGS

Lede rigid couplings can be used in applica�ons where you require a rigid joint similar to that of a tradi�onal anged, welded and or threaded connec�on. You need not worry about the snaking of the pipe on straight runs, as all Lede rigid couplings u�lize both a mechanical and fric�onal interlock design to provide rigidity. Rigid couplings eliminate or reduce undesired angular movement, axial displacement and rota�on a�er installa�on as is required under normal service condi�ons. Rigid couplings are some of the most popular and most widely used today.

Lede offers two different types of rigid couplings, the angle-pad design, the T&G (tongue and groove) design.

FLEXIBLE COUPLINGS

Lede exible couplings allow for full design features in applica�ons such as curved or deected layouts and or when systems are exposed to outside forces beyond normal sta�c condi�ons such as seismic events or where vibra�on and or noise a�enua�on are a concern. The ability to design in controlled exibility is an advantageous feature when compared to tradi�onal rigid joining methods such as threading, anging and welding. When designing with exible couplings you must allow for proper support to the system so as to eliminate undesired stress (see Anchoring, hanging and supports on page 48).

There are several published standards and codes covering grooved piping component. These codes or standards may vary as to the deni�on or standard for exible couplings. System designers should conrm which standard (s) and or code(s) are required for the system being designed and they should select the applicable coupling for the applica�on.

The most popular and most widely used couplingstoday

DESIGN FEATURES

Type Model Nos.

≥1°

<1°

<1°

1.6 - 3.2

<1.6

<1.6

Yes

No

No

XGQT2, XGQT31212

GKS, 1512, XGQT4

XGQT1, 31HP

Flexible Coupling

Angle-paddesign

AngularMovement

deg.

AxialDisplacement

mm

Rota�ona�er

installa�on

T&G design

Rigi

d Co

uplin

g

Note:

Angularmovement

D

Axialdisplacement

Rotationalmovement

1) Angilar movement of exible coupling 8” and larger sizes should be 0.5°.2) Axial displacement data based on roll-grooved pipe.

04�|�DESIGN�FEATURES

page 2ARGCO.comGrooved Piping Products Catalog Updated 7/28/2020 © ARGCO

RIGID or FLEXIBLE? ARGCO grooved couplings are classified into two types, flexible and rigid. The following information is intended for system designers and installers to better understand the nature of the grooved piping systems. This will allow the designer and installer to make better use of the design features and advantages of grooved piping components and systems

RIGID COUPLINGSARGCO rigid couplings can be used in application where you re-quire a rigid joint similar to that of a traditional flanged, welded and or threaded connection. You need not worry about the snak-ing of the pipe on straight runs, as all ARGCO rigid couplings uti-lize both a mechanical and frictional interlock design to provide rigidity. Rigid couplings eliminate or reduce undesired angular movement, axial displacement and rotation after installation as is required under normal service conditions. Rigid couplings are some of the most popular and most widely used today.

ANGLE-PAD DESIGNAngle-pad design: As the bolts are tightened, the angled bolt pads slide in opposite directions causing the couplings keys to ghtly grip the pipe, while at the same me the pipe grooves are forced outward against the coupling keys.

T&G design: The T&G (tongue & groove) mechanism provides a mechanical and frictional interlock resulting in a rigid joint which reduces undesired angular movement. ARGCO precision casting techniques allow the coupling seg-ments to meet metal-to-metal when installed on properly grooved pipe.

DESIGN FEATURES

TYPE

Flexible Coupling

Rigid Coupling

ANGULARMOVEMENT

DEG.

>1°

<1°

AXIALDISPLACEMENT

1.6 - 3.2

<1.6

ROTATIONAFTER

INSTALLATION

Yes

No

MODELNO'S

104

101

Note: Angular movement of flexible coupling 8" and larger sizes should be 0.5°. Axial displacement data based on roll-grooved pipe.

RIGID OR FLEXIBLE?




RIGID COUPLINGS



FLEXIBLE COUPLINGS




DESIGN FEATURES

Type Model Nos.

≥1°

<1°

<1°

1.6 - 3.2

<1.6

<1.6

Yes

No

No

XGQT2, XGQT31212

GKS, 1512, XGQT4

XGQT1, 31HP

Flexible Coupling

Angle-paddesign

AngularMovement

deg.

AxialDisplacement

mm

Rota�ona�er

installa�on

T&G design

Rigi

d Co

uplin

g

Note:

Angularmovement

D

Axialdisplacement

Rotationalmovement



RIGID OR FLEXIBLE?




RIGID COUPLINGS



FLEXIBLE COUPLINGS




DESIGN FEATURES

Type Model Nos.

≥1°

<1°

<1°

1.6 - 3.2

<1.6

<1.6

Yes

No

No

XGQT2, XGQT31212

GKS, 1512, XGQT4

XGQT1, 31HP

Flexible Coupling

Angle-paddesign

AngularMovement

deg.

AxialDisplacement

mm

Rota�ona�er

installa�on

T&G design

Rigi

d Co

uplin

g

Note:

Angularmovement

D

Axialdisplacement

Rotationalmovement



Axial Displacement & Angular Movement (Models XGQT2 & 1212)

NFPA 13 denes a exible coupling as;

�a listed coupling or ��ng that allows a�ial displacement, rota�on, and at least 1 degree of angular movement of the pipe without inducing harm on the pipe. For pipe diameters of 8 in. and larger, the angular movement shall �e permi�ed to �e less than 1 degree �ut not less than 0.5 degrees.” (NFPA 13-2007 3.5.4)

For sprinkler systems, NFPA 13 species the use of exible couplings to protect the system against damage from earthquakes and sets some specic examples of how

and where they should be used. Designers and installers should design their re protec�on systems in compliance with this standard. See Typical Applica�ons – Flexible Couplings on Page 44.

20

0.75

25

1

32

1.25

40

1.5

50

2

65

2.5

65

2.5

80

3

90

3.5

100

4

100

4

125

5

125

5

125

5

125

5

26.7

1.050

33.4

1.315

42.4

1.660

48.3

1.900

60.3

2.375

73

2.875

76.1

3.000

88.9

3.500

1016

4.000

108.0

4.25

114.3

4.500

127.0

5.000

133

5.250

139.7

5.500

141.3

5.563

1.6

0.0625

1.6

0.0625

1.6

0.0625

1.6

0.0625

1.6

0.0625

1.6

0.0625

1.6

0.0625

1.6

0.0625

1.6

0.0625

3.2

0.125

3.2

0.125

3.2

0.125

3.2

0.125

3.2

0.125

3.2

0.125

118

1.42

96

1.16

76

0.91

66

0.80

53

0.63

44

0.52

42

0.50

36

0.43

31

0.38

59.0

0.71

55

0.67

50.0

0.60

48

0.58

46

0.55

45

0.54

6°-46ˊ

5°-30ˊ

4°-20ˊ

3°-48ˊ

3°-01ˊ

2°-30ˊ

2°-24ˊ

2°-04ˊ

1°-48ˊ

3°-24ˊ

3°-12ˊ

2°-53ˊ

2°-46ˊ

2°-37ˊ

2°-36ˊ

Size Angular Movement(Deec on)

AxialDisplace

-mentmm/in

Nom.Sizemm/in

Actual ODmm/in

Per couplingdegrees

Per pipemm/m, in/

150

6

150

6

150

6

200 JIS

8

200

8

250 JIS

10

250

10

300 JIS

12

300

12

350

14

400

16

450

18

500

20

550

22

600

24

159.0

6.250

165.1

6.500

168.3

6.625

216.3

8.516

219.1

8.625

267.4

10.528

273.0

10.750

318.5

12.539

323.9

12.750

355.6

14.000

406.4

16.000

457.0

18.000

508.0

20.000

559.0

22.000

610.0

24.000

3.2

0.125

3.2

0.125

3.2

0.125

3.2

0.125

3.2

0.125

3.2

0.125

3.2

0.125

3.2

0.125

3.2

0.125

3.2

0.125

3.2

0.125

3.2

0.125

3.2

0.125

3.2

0.125

3.2

0.125

40

0.48

39

0.47

38

0.45

30

0.36

29

0.35

24

0.29

23

0.28

20

0.25

20

0.24

18

0.22

16

0.19

14

0.17

13

0.15

11

0.13

10

0.13


AxialDisplace

-mentmm/in

Nom.Sizemm/in

Actual ODmm/in

Per couplingdegrees

Per pipemm/m, in/

2°-18ˊ

2°-14ˊ

2°-10ˊ

1°-42ˊ

1°-40ˊ

1°-22ˊ

1°-20ˊ

1°-10ˊ

1°-08ˊ

1°-02ˊ

0°-54ˊ

0°-48ˊ

0°-44ˊ

0°-38ˊ

0°-36ˊ

Flexible Coupling

Note: Axial displacement is the maximum value when the system is pressurized to the maximum working pressure.Angular movement is the maximum value that a coupling allows under no internal pressure.

DESIGN�FEATURES�|�05

DESIGN FEATURESDesigners and installers should designtheir fire protection systems in compliancewith this standard.

Axial Displacement & Angular Movement (Models XGQT2 & 1212)

NFPA 13 denes a exible coupling as;

�a listed coupling or ��ng that allows a�ial displacement, rota�on, and at least 1 degree of angular movement of the pipe without inducing harm on the pipe. For pipe diameters of 8 in. and larger, the angular movement shall �e permi�ed to �e less than 1 degree �ut not less than 0.5 degrees.” (NFPA 13-2007 3.5.4)

For sprinkler systems, NFPA 13 species the use of exible couplings to protect the system against damage from earthquakes and sets some specic examples of how

and where they should be used. Designers and installers should design their re protec�on systems in compliance with this standard. See Typical Applica�ons – Flexible Couplings on Page 44.

20

0.75

25

1

32

1.25

40

1.5

50

2

65

2.5

65

2.5

80

3

90

3.5

100

4

100

4

125

5

125

5

125

5

125

5

26.7

1.050

33.4

1.315

42.4

1.660

48.3

1.900

60.3

2.375

73

2.875

76.1

3.000

88.9

3.500

1016

4.000

108.0

4.25

114.3

4.500

127.0

5.000

133

5.250

139.7

5.500

141.3

5.563

1.6

0.0625

1.6

0.0625

1.6

0.0625

1.6

0.0625

1.6

0.0625

1.6

0.0625

1.6

0.0625

1.6

0.0625

1.6

0.0625

3.2

0.125

3.2

0.125

3.2

0.125

3.2

0.125

3.2

0.125

3.2

0.125

118

1.42

96

1.16

76

0.91

66

0.80

53

0.63

44

0.52

42

0.50

36

0.43

31

0.38

59.0

0.71

55

0.67

50.0

0.60

48

0.58

46

0.55

45

0.54

6°-46ˊ

5°-30ˊ

4°-20ˊ

3°-48ˊ

3°-01ˊ

2°-30ˊ

2°-24ˊ

2°-04ˊ

1°-48ˊ

3°-24ˊ

3°-12ˊ

2°-53ˊ

2°-46ˊ

2°-37ˊ

2°-36ˊ


AxialDisplace

-mentmm/in

Nom.Sizemm/in

Actual ODmm/in

Per couplingdegrees

Per pipemm/m, in/

150

6

150

6

150

6

200 JIS

8

200

8

250 JIS

10

250

10

300 JIS

12

300

12

350

14

400

16

450

18

500

20

550

22

600

24

159.0

6.250

165.1

6.500

168.3

6.625

216.3

8.516

219.1

8.625

267.4

10.528

273.0

10.750

318.5

12.539

323.9

12.750

355.6

14.000

406.4

16.000

457.0

18.000

508.0

20.000

559.0

22.000

610.0

24.000

3.2

0.125

3.2

0.125

3.2

0.125

3.2

0.125

3.2

0.125

3.2

0.125

3.2

0.125

3.2

0.125

3.2

0.125

3.2

0.125

3.2

0.125

3.2

0.125

3.2

0.125

3.2

0.125

3.2

0.125

40

0.48

39

0.47

38

0.45

30

0.36

29

0.35

24

0.29

23

0.28

20

0.25

20

0.24

18

0.22

16

0.19

14

0.17

13

0.15

11

0.13

10

0.13


AxialDisplace

-mentmm/in

Nom.Sizemm/in

Actual ODmm/in

Per couplingdegrees

Per pipemm/m, in/

2°-18ˊ

2°-14ˊ

2°-10ˊ

1°-42ˊ

1°-40ˊ

1°-22ˊ

1°-20ˊ

1°-10ˊ

1°-08ˊ

1°-02ˊ

0°-54ˊ

0°-48ˊ

0°-44ˊ

0°-38ˊ

0°-36ˊ

Flexible Coupling

Note: Axial displacement is the maximum value when the system is pressurized to the maximum working pressure.Angular movement is the maximum value that a coupling allows under no internal pressure.



NFPA 13 defines a FLEXIBLE COUPLING as;“a listed coupling or fitting that allows axial displacement,rotation, and at least 1 degree of angular movement of the pipe without inducing harm on the pipe. For pipe diameters of 8 in. and larger, the angular movement shall be permitted to be less than 1 degree but not less than 0.5 degrees.” (NFPA 13-2007 3.5.4)For sprinkler systems, NFPA 13 specifies the use of flexible cou-plings to protect the system against damage from earthquakes and sets some specific examples of how and where they should be used.

MATERIALSHOUSINGThe housing segments not only provide significant strength to the joint but they also compress and protect the gasket fromexposure, ARGCO coupling housings and components are cast in a variety of materials as shown below.

DESIGN FEATURES


MATERIALS

The housing segments not only provide signicant strength to the joint but they also compress and protect the gasket from exposure, Lede coupling housings and components are cast in a variety of materials as shown below.

Duc le Iron: Standard coupling housings and �ngs are made of duc�le iron conforming to ASTM A536 Gr. 65-45-12. The proper�es of Grade 65-45-12 duc�le iron are as follows; 65,000 psi (448 MPa) tensile strength, 45,000 psi (310 MPa) yield strength and 12% elonga�on. As an

op�on we also offer duc�le iron made to ASTM A395 Gr. 60-40-18, for applica�ons where required or where boiler codes may apply.

Stainless Steel: We offer a variety of stainless steel cas�ng materials depending on your intended applica�on. Standard coupling housing and �ng materials include CF8 (304), CF8M (316) or CF3M (316L) per ASTM A743. Op�onal

materials include 2205 Duplex, 2507 Super Duplex and ASTM CK-3MCuN (UNSJ93245), equivalent to 254SMO*.(* 254SMO is a registered trademark of Avesta Polarit AQB.)

Lede gaskets are available in a variety of congura�ons and compounds to meet your specic requirements. These gaskets have excellent self sealing capabili�es and

are designed to provide a leak �ght seal. During assembly the gasket is rst stretched over the pipe ends which forms the ini�al seal. As the housing segments are installed and secured the pressure responsive gasket is slightly compressed to form a leak-�ght joint. The strength of the seal is further enhanced by internal line pressure that creates downward pressure on the lips of the gasket. The gasket also seals well under vacuum condi�ons up to 10 inHg (254 mmHg) which may occur when a system is drained. Please refer to the Lede Gasket Selec�on Guide for addi�onal details and gasket materials.

Lede products u�lize oval neck track bolts and heavy duty hex nuts, available either in UNC threaded or ISO metric threaded. The oval neck track bolts mate into the oval holes in the housing segments to allow for easy �ghtening using only a single wrench/spanner. The UNC bolts and nuts are electro zinc plated in a silver chromate color and ISO bolts and nuts in a gold chromate color. Hot-dip galvanized bolts and nuts are also available upon request. (M10 to M22 only)

Stainless steel track bolts and nuts, type 304 or 316, are supplied with Lede stainless steel couplings. Stainless steel track bolts and nuts are molybdenum disulde (MoS2) coated to inhibit galling.

HOUSINGS

BOLTS AND NUTS

GASKETS

A stainless steel boltfastened with a siliconebronze nut


MATERIALS










HOUSINGS

BOLTS AND NUTS

GASKETS



NUTS & BOLTSARGCO products utilize oval neck track bolts and heavy duty hex nuts, available either in UNC threaded or ISO metric threaded. The oval neck track bolts mate into the oval holes in the housing segments to allow for easy tightening using only a single wrench/spanner. The UNC bolts and nuts are electro zinc plated in a silver chromate color and ISO bolts and nuts in a goldchromate color. Hot-dip galvanized bolts and nuts are also available upon request. (M10 to M22 only)

Stainless steel track bolts and nuts, type 304 or 316, are supplied with ARGCO stainless steel couplings. Stainless steel track bolts and nuts are molybdenum disulfide (MoS2) coated to inhibit galling.

Stainless Steel: ARGCO offers a variety of stainless steel casting materials depending on your intendedapplication. Standard coupling housing and fitting materials include CF8 (304), CF8M (316) or CF3M (316L) per ASTM A743. Optional materials include 2205 Duplex, 2507 Super Duplex and ASTM CK-3MCuN (UNSJ93245), equivalent to 254SMO*. (* 254SMO is a registered trademark of Avesta Polarit AQB.)Most of these materials are special order. Call your sales rep for details.

GASKETSARGCO gaskets are available in a variety of configurations and compounds to meet your specific requirements. These gaskets have excellent self sealing capabilities and are designed to provide a leak tight seal. During assembly the gasket is first stretched over the pipe ends which forms the inial seal. As the housing segments are installed and secured the pressure responsive gasket is slightly compressed to form a leak-tight joint. The strength of the seal is further enhanced by internal line pressure that creates downward pressure on the lips of the gasket. The gasket also seals well under vacuum conditions up to 10 inHg (254 mmHg) which may occur when a system is drained. Please refer to the ARGCO Gasket Selection Guide for additional details and gasket materials.

MATERIALS










HOUSINGS

BOLTS AND NUTS

GASKETS



Ductile Iron: Standard coupling housings and fittings are made of ductile iron conforming to ASTM A536 Gr. 65-45-12. The properties of Grade 65-45-12 ductile iron are as follows; 65,000 psi (448 MPa) tensile strength, 45,000 psi (310 MPa) yield strength and 12% elongation. As an option we also offer ductile iron made to ASTM A395 Gr. 60-40-18, for applications where required or where boiler codes may apply.

ARGCO.comGrooved Piping Products Catalog Updated 7/28/2020 © ARGCO

DATA CHART NOTES

Nominal Size: ARGCO couplings and fittings are identified by the nominal IPS pipe size in inches or nominal diameter of pipe (DN) in millimeters.

Pipe OD: Actual outside diameter of pipe in inches and millimeters.Maximum Working Pressure: Maximum working pressures listed are CWP (cold water pressure) or maximum allowed working pressure within the service temperature range of the gasket used in the coupling, based on standard wall or sch. 7/10/40 steel pipe, cut or roll-grooved to ANSI/AWWA C606-04 specifications. These ranges may occasionally differ from maximum working pressures listed and/or approved by UL, ULC, and/or FM as testing conditions and test pipes differ. For performance data on other pipe schedules contact ARGCO.Note: For one time field test only the maximum joint working pressure may be increased 1.5 times the figures shownMaximum End Load: Maximum end loads listed are total of internal and external forces to which the joint can be subjected, based on standard wall or sch. 7/10/40 steel pipe, cut or roll-grooved to ANSI/AWWA C606-04 specifications.Axial Displacement: Designed range of the gap between pipe ends based on roll grooved pipe.Angular Movement (Deflection): Maximum allowable deflection of pipe from centerline when the joint is used with cut or roll-grooved steel pipe under no internal pressure.Dimensions: “A”, “B”, “C” and so on are external dimensions for reference purpose only in millimeters and inchesBolt Size: UNC bolt size and length in inches and ISO metric bolt size and length in millimeters with numbers of bolts where ap-plicable.Bolt Torque: Recommended bolt fastening torque in Lbs-Ft and N-m.

GENERAL NOTES

Service Fluid and Temperature: Service fluid and temperature limitations for ARGCO couplings are primarily governed by the gasket used within the coupling. Always refer to and consult the ARGCO Gasket Selection Guide.

Working Pressure: ARGCO grooved couplings are generally engineered for use with standard or sch. 7/10/40 steel pipes (except for some high pressure models) and can be used within the rated working pressures as shown in the ARGCO literature. A one me only field test at 1.5 times the working pressure is allowed.

As there are limitations in service temperatures, the ARGCO couplings and fittings do not adopt the ANSI temperature- pressure ranges (Class 150, Class 300, etc.), ISO or JIS methods of pressure ranges (PN10, PN16, JIS 10K or 20K, etc.). All the published work-ing pressures are CWP, non-shock cold water pressures, unless otherwise specified. Actual allowed working pressures for a specific coupling will vary depending on the coupling size, pipe material, pipe schedule (or thickness) and types of grooves used. Special attention is required when using thin wall stainless steel pipe such as sch. 5. For further details request the performance data for specific thin wall pipe.The dimensions, weights, performance data, and other specifications shown in this catalog supersede all previous published data.

ARGCO reserves the right to change product designs and or specifications without notice and without obligation.Illustrations shown within this catalog are for illustrative purposes. They are not drawn to scale and may have been exaggerated for clarity. Any person who makes use of the information or materials contained herein shall do so at their own risk and shall be liable for any results arising from such use.

DESIGN FEATURES

DATA CHART

NominalSize

mm/in

1

Max.WorkingPressureBar/PSI

Max.EndLoad

kN/Lbs

AxialDisplacement

mm/inDegree PerCoupling(°)

Pipemm/m in/

Bolt Sizein

BoltTorque

N-m/Lbs-FtA

mm/inB

mm/inC

mm/in

Angular Movement DimensionsPipeO.D.

mm/in

DATA CHART NOTES

GENERAL NOTES

Nominal Size: Lede couplings and �ngs are iden�ed by the nominal IPS pipe size in inches or nominal diameter of pipe (DN) in millimeters.

Service Fluid and Temperature: Service uid and temperature limita�ons for Lede couplings are primarily governed by the gasket used within the coupling. Always refer to and consult the Lede Gasket Selec�on Guide.

Working Pressure: Lede grooved couplings are generally engineered for use with standard or sch. 7/10/40 steel pipes (except for some high pressure models) and can be used within the rated working pressures as shown in the Lede literature. A one �me only eld test at 1.5 �mes the working pressure is allowed.

As there are limita�ons in service temperatures, the Lede couplings and �ngs do not adopt the ANSI temperature- pressure ra�ngs (Class 150, Class 300, etc.), ISO or JIS methods of pressure ra�ngs (PN10, PN16, JIS 10K or 20K, etc.). All the published working pressures are CWP, non-shock cold water pressures, unless otherwise specied. Actual allowed working

pressures for a specic coupling will vary depending on the coupling size, pipe material, pipe schedule (or thickness) and types of grooves used. Special a�en�on is required when using thin wall stainless steel pipe such as sch. 5. For further details request the performance data for specic thin wall pipe.

The dimensions, weights, performance data, and other specica�ons shown in this catalog supersede all previous published data. Lede reserves the right to change product designs and or specica�ons without no�ce and without obliga�on.

Illustra�ons shown within this catalog are for illustra�ve purposes. They are not drawn to scale and may have been exaggerated for clarity. Any person who makes use of the informa�on or materials contained herein shall do so at their own risk and shall be liable for any results arising from such use.

Maximum End Load: Maximum end loads listed are total of internal and external forces to which the joint can be subjected, based on standard wall or sch. 7/10/40 steel pipe, cut or roll-grooved to ANSI/AWWA C606-04 specica�ons.

1

Pipe OD: Actual outside diameter of pipe in inchs and millimeters.

2

Maximum Working Pressure: Maximum working pressures listed are CWP (cold water pressure) or maximum allowed working pressure within the service temperature range of the gasket used in the coupling, based on standard wall or sch. 7/10/40 steel pipe, cut or roll-grooved to ANSI/AWWA C606-04 specica�ons.These ra�ngs may occasionally differ from maximum working pressures listed and/or approved by UL, ULC, and/or FM as tes�ng condi�ons and test pipes differ. For performance data on other pipe schedules contact Lede.

Note: For one �me eld test only the maximum joint working pressure may be increased 1.5 �mes the gures shown.

3

4

Axial Displacement: Designed range of the gap between pipe ends based on roll grooved pipe.

5

Dimensions: “A”, “B”, “C” and so on are external dimensions for reference purpose only in millimeters and inches.

7

Bolt Torque: Recommended bolt fastening torque in Lbs-Ft and N-m.

9

Angular Movement (Deec on): Maximum allowable deec�on of pipe from centerline when the joint is used with cut or roll-grooved steel pipe under no internal pressure.

6

Bolt Size: UNC bolt size and length in inches and ISO metric bolt size and length in millimeters with numbers of bolts where applicable.

8

2 3 4 5 8 96 7

10�|�DATA�CHART


GROOVED COUPLINGS - STANDARD RIGIDModel 101

Available Sizes• 1" through 12" (25 through 300 mm)Pipe Material• Carbon steel, Schedule 10, Schedule 40. For use with alternative materials and wall thicknesses please contact ARGCO.Maximum Working Pressure• Up to 300 psi/2517 kPa.Function• Joins carbon steel pipe.• Provides a rigid pipe joint designed to restrict axial or angular movement.CERTIFICATIONS/LISTINGSUnderwriters Laboratories, Underwriters Laboratories Canada, Factory Mutual.

SPECIFICATIONS - MATERIALHousing Sections: Ductile Iron conforming to ASTM A 536, Grade 65-45-12.

Housing Coating: Standard: Orange EnamelAvailable: Hot Dipped Galvanized

Gasket: Standard: Grade E EPDM (Type A)ARGCO's products are listed by Underwriters Laboratories UL Canada and Approved by Factory Mutual for we and dry (oil free air) sprinkler services within the rated working pressure.

Bolts and NutsStandard: Carbon Steel oval neck track bolts meeing ASTM A449 and ISO 898-1. Carbon steel hex nuts meet ASTM A563 Grade B.Nuts and Bolts are zinc electroplated per ASTM B633 NZ/FE5, finish Type III.Available: Stainless Steel. Meets ASTM F593, Group 2 (316 stainless steel), condition CW. Hex nuts meets ASTM F594, Group 2 (316 stainless steel), condition CW, with galling-resistant coating.

The ARGCO Model 101 is an angle-pad design standard rigid coupling for moderate pressure piping services including fire mains, long straight runs and value con-nections. The angle-pad design allows the coupling housings to slide along the bolt pads when tightened. The result is an offset clamping action which provides a rigid joint which resists so-called ‘snaking’ of a long straight run. Support and hanging requirements correspond to ANSI B31.1, B31.9 and NFPA 13. With the removal of only one bolt you can make a fast and easy ‘swing-over’ installa-tion.



ARGCO Grooved Couplings are suitable for fire protection systems, water supply systems, and other process systems of higher working pressure.

GROOVED COUPLINGS

MODEL 1512 STANDARD RIGID COUPLING

The Lede Model 1512 is an angle-pad design standard rigid coupling for general piping applica�ons where rigidity is required including value connec�ons, mechanical rooms, re mains and long straight runs. The angle-pad design allows the coupling housings to slide along the bolt pads when �ghtened. The result is an offset clamping ac�on which provides a rigid joint that resists exural and torsional loads. Support and hanging reguirements correspond to ANSI B31.1, B31.9 and NFPA 13.

Sizes available: 32mm-300mm / 1-1/4’’~12’’Working Pressure: Up to 35 bar / 500 psi

- Angle-Pad Design -

3211/440

11/2502

6521/265

21/2803

1004

1255

1255

1506

1506

2008

2008

25010

25010

30012

30012

42.41.66948.31.9

60.32.375

732.87576.1

388.93.5

114.34.5

139.75.5

141.35.563165.1

6.5168.36.625216.38.515219.18.625267.4

10.527273

10.75318.5

12.539323.912.75

3550035

50035

50035

50035

50035

50035

50035

50035

50035

50035

50035

50035

50035

50035

50035

50035

500

2.92 656 3.79 852 9.84 2212 14.64 3240 15.68 3523 21.39 4808 35.36 7948 52.83 11874 48.59 10930 66.33 14920 76.67 17233 126.64 28465 129.94 29206 193.55 43502 201.74 45344 274.59 61718 283.98 63828

0-1.60-0.060-1.6

0-0.060-1.7

0-0.070-1.7

0-0.070-1.7

0-0.070-1.7

0-0.070-4.1

0-0.160-4.1

0-0.160-4.1

0-0.160-4.1

0-0.160-4.1

0-0.160-3.2

0-0.130-3.2

0-0.130-3.2

0-0.130-3.2

0-0.130-3.2

0-0.130-3.2

0-0.13

642.52

692.72

883.46 100

3.94 101.64.00 116

4.57 144.45.69 171.66.76 172

6.77 198

7.80 200

7.87 265

10.43 263.410.37

31712.48

32612.83

37514.76

38115.00

1064.17 113

4.45 122

4.80 142

5.59 142

5.59 158

6.22 194

7.64 230

9.06 231

9.09 255

10.04 256

10.08 334

13.15 334

13.15 396

15.59 404

15.91 464

18.27 468

18.43

471.85

471.85

471.85

471.85

471.85

471.85

512.01

522.05

522.05

532.09

532.09

632.48

632.48

652.56

652.56

652.56

652.56

M10×603/8×2-3/8M10×60

3/8×2-3/8M10×60

3/8×2-3/8M12×70

1/2×2-3/4M12×70

1/2×2-3/4M12×70

1/2×2-3/4M12×70

1/2×2-3/4M16×85

5/8×3-1/3M16×85

5/8×3-1/3M16×85

5/8×3-1/3M16×85

5/8×3-1/3M20×1203/4×4-3/4M20×1203/4×4-3/4M22×1907/8×7-1/2M22×1907/8×7-1/2M22×1907/8×7-1/2M22×1907/8×7-1/2

NominalSize

mm/in


Max.EndLoad

KN/Lbs

AxialDisplacement

mm/inA

mm/inB

mm/inC

mm/in No. mm/in

Dimensions Bolts SizePipe O.D.mm/in

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

Item #

7010001

7010002

7010003

7010004

7010005

7010006

7010007

7010008

7010009

7010010

7010011

7010012

Nominal Sizein/mm

1"25

1-1/4"32

1-1/2"402" 50

2-1/2" 653" 804"

1005"

1256"

1508"

20010"25012"300

Pipe O.D.in/mm1.32733.7

1.66942.41.9

48.32.375 60.3

2.875 733.5

88.94.5

114.35.5125

6.625168.38.625219.110.75273

12.75323.9

MaximumWorking Pressurepsi/kPa

30020

30020

30020

30020

30020

30020

30020

30020

30020

30020

30020

30020

MaximumEnd Load

lb/N

4051.806562.928523.7913275.9119458.66288512.84425818.94645728.73922941.061707975.9926101116.1337031164.76

AxialDisplacement

in/mm

0-0.060-1.6

0-0.060-1.6

0-0.060-1.6

0-0.060-1.6

0-0.060-1.6

0-0.060-1.6

0-0.160-4.1

0-0.160-4.1

0-0.060-4.1

0-0.160-4.1

0-0.160-4.1

0-0.160-4.1

Binches

mm3.8297

4.23107.54.491144.881245.391376.141567.321868.392139.61244

13.39340

15.75400

18.27464

Dimensions

C inches

mm1.7745

1.7745

1.7745

1.8146

1.8146

1.8146

1.9750

1.9750

1.9750

2.4462

2.5264

2.5264

Ainches

mm2.1755

2.5063.52.7269

3.2983.63.8698

4.491145.431386.461647.56192

10.00254

12.32313

14.49368

Bolt inches

mm3/8" x1-1/2"

M10x403/8" x1-3/4"

M10x453/8" x1-3/4"

M10x453/8" x 2-1/8"

M10x553/8" x 2-1/8"

M10x553/8" x 2-1/8"

M10x551/2" x 2-5/8"

M12x651/2" x 2-5/8"

M12x651/2" x 2-5/5"

M12x653/4" x3-1/2 "

M16x903/4" x3-1/2"

M20x907/8" x4-1/3"M22x110

• Working Pressure and End Load are total, from all internal and external loads, based on standard weight (ANSI) steel pipe, standard roll or cut grooved in accordance with ARGCO specifications. • The allowable pipe separation dimension shown is for system layout purposes only. ARGCO couplings are considered rigid connections and will not accommodate expansion or contraction of the piping system.• When assembling ARGCO couplings onto end caps, take additional care to make certain the end cap is fully seated against the gasket end stop.

User Responsibility for Product Selection and SuitabilityEach user bears final responsibility for making a determination as to the suitability of ARGCO products for a particular end-use application, in accordance with industry stan-dards and project specifications, and the applicable building codes and related regulations as well as ARGCO performance, maintenance, safety, and warning instructions. Nothing in this or any other document, nor any verbal recommendation, advice, or opinion from any ARGCO employee, shall be deemed to alter, vary, supersede, or waive any provision of Allied Rubber and Gasket Company's standard conditions of sale, installation guide, or this disclaimer.NoteAll products to be installed in accordance with current ARGCO installation/assembly instructions. ARGCO reserves the right to change product specifications, designs and standard equipment without notice and without incurring obligations.InstallationReference should always be made to the ARGCO installation instructions of the product you are installing. WarrantyRefer to the Warranty section of the current Price List or contact ARGCO for details.

INSTALLATION INSTRUCTIONS:

STANDARD RIGID COUPLINGDepressurize and drain the piping system before attemptingto install, remove, or adjust any piping products.Wear safety glasses, hardhat, and foot protection.

1. CHECK PIPE ENDS:The outside surface of the pipe from the pipe end to the groovemust be smooth and free from indentations, projections(including weld seams), and roll marks to ensure a leaktightseal for the gasket. All oil, grease, loose paint, and dirt mustbe removed.

2. CHECK GASKET AND LUBRICATE :Check the gasket to make sure it is suitable for the intendedservice. Apply a thin coat of Tuf-Lube Gasket GreaseLubricant to the gasket lips and exterior.

3. POSITION GASKET:Position the gasket over the pipe end. Make sure the gasket does not overhang the pipe end.

4. JOIN PIPE ENDS:Align and bring the two pipe ends together. Slide the gasket into position, and make sure it is centered between the grooves in each pipe.Make sure no portion of the gasket extends into the groove in either pipe.

5. ASSEMBLE HOUSINGS:Insert one bolt into the housings, and thread the nut loosely onto the bolt (nut should be flush with end of bolt) .

6. INSTALL HOUSINGS:Install the housings over the gasket. Make sure the housings’ keys engage the grooves properly on both pipes.

Torque ValueWhen a torque value is specified for coupling installation, this torque MUST be applied to the nuts in order to achieve proper installation. However, torque beyond specified values will not improve sealing.Exceeding the specified torque by more than 25% may cause damage to the product, resulting in pipe-joint failure.

Using Impact WrenchesWhen using an impact wrench, the speed of assembly may require extra care to ensure nuts are tightened evenly by alternating sides until proper assembly is complete.Impact wrenches do not provide the installer with direct “wrench feel” or torque to judge nut tightness. Since some impact wrenches are capable of high output, it is important to develop a familiarity with the impact wrench to avoid damaging or fracturing bolts or coupling bolt pads during installation.DO NOT continue to use an impact wrench after the visual installation guidelines for the coupling are achieved.Perform trial assemblies with the impact wrench and socket or torque wrenches to help determine the capability of the impact wrench. Using the same method, periodically check additional nuts throughout the system installation.In addition, verify that proper impact grade sockets are being used for couplinginstallation.

SIZE1”1-1/4”1-1/2”2”2-1/2”3”3-1/2”4”

MIN303030808080

100100

MAX454545

100100100130130

SPECIFIED TORQUE (LB/FT.)




GROOVED COUPLINGS - STANDARD FLEXIBLEModel 104

Available Sizes• 1" through 12" (25 through 300 mm)Pipe Material• Carbon steel, Schedule 10, Schedule 40. For use with alternative materials and wall thicknesses please contact ARGCO.Maximum Working Pressure• Up to 300 psi/2517 kPa.Function• Joins carbon steel pipe.• Provides a rigid pipe joint designed to restrict axial or angular movement.CERTIFICATIONS/LISTINGSUnderwriters Laboratories, Underwriters Laboratories Canada, Factory Mutual.






Item #

7010015

7010016

7010017

7010018

7010019

7010020

7010021

7010022

7010023

7010024

7010025

7010026

NominalSize

in/mm1"25

1-1/4"32

1-1/2"402" 50

2-1/2" 653" 804"

1005"

1256"

1508"

20010"25012"300

MaximumWorking Pressurepsi/kPa

30020

30020

30020

30020

30020

30020

30020

30020

30020

30020

30020

30020

MaximumEnd Load

lb/N

4051.806562.928523.7913275.9119458.66288512.84425818.94645728.73922941.061707975.9926101116.1337031164.76

AxialDisplacement

in/mm0.0625

1.60.0625

1.60.0625

1.60.0625

1.60.0625

1.60.0625

1.60.125

3.20.125

3.20.125

3.20.125

3.20.125

3.20.125

3.2

Binches

mm3.8297

4.23107.54.491144.881245.391376.141567.321868.392139.61244

13.39340

15.75400

18.27464

Dimensions

C inches

mm1.7745

1.7745

1.7745

1.8146

1.8146

1.8146

1.9750

1.9750

1.9750

2.4462

2.5264

2.5264

Ainches

mm2.1755

2.5063.52.7269

3.2983.63.8698

4.491145.431386.461647.56192

10.00254

12.32313

14.49368

Bolt inches

mm3/8" x1-1/2"

M10x403/8" x1-3/4"

M10x453/8" x1-3/4"

M10x453/8" x 2-1/8"

M10x553/8" x 2-1/8"

M10x553/8" x 2-1/8"

M10x551/2" x 2-5/8"

M12x651/2" x 2-5/8"

M12x651/2" x 2-5/8"

M12x653/4" x 3-1/2"

M20x903/4" x3-1/2"

M20x907/8" x4-1/3"M22x110

Note: Allowable Axial Displacement figures are for roll grooved standard steel pipe. Values for cut grooved pipe will be double that of roll grooved. These values are maximums; for design and installation purposes these figures should be reduced by: 50% for ¾” – 3½”; 25% for 4” and larger to com-pensate for jobsite conditions.• Working Pressure and End Load are total, from all internal and external loads, based on standard weight (ANSI) steel pipe, standard roll or cut grooved in accordance with ARGCO specifications. • When assembling ARGCO couplings onto end caps, take additional care to make certain the end cap is fully seated against the gasket end stop.

ARGCO Grooved Couplings are suitable for fire protection systems, water supply sys-tems, and other process systems of higher working pressure.

The NFPA 13 defines a flexible coupling as;

"a listed coupling or fitting that allows axial displacement, rotation, and at least 1 degree of angular movement of the pipe without inducing harm on the pipe. For pipe diameters of 8 in. and larger, the angular movement shall be permitted to be less than 1 degree but not less than 0.5 degrees.” (NFPA 13- 2007 3.5.4)

For sprinkler systems, NFPA 13 specifies the use of flexible couplings to protect the system against damage from earthquakes and sets some specific examples of how and where they should be used. Designers and installers should design their fire protection sys-tems in compliance with this standard.

per couplingdegrees5° - 30'

4° - 20'

3° - 48'

3° - 01'

2° - 30'

2° - 04'

3° - 14'

2° - 53'

2° - 18'

1° - 40'

1° - 20'

1° - 08'

per pipein/ft, mm/m

0.7158

0.5848

0.45380.433

0.3126

0.2118

0.3428

0.2723

0.2319

0.1815

0.1412

0.1210

Angular Movement

GROOVED COUPLINGS - STANDARD FLEXIBLEModel 104


1.66942.41.9

48.32.375 60.3

2.875 733.5

88.94.5

114.35.5125

6.625168.38.625219.110.75273

12.75323.9


GROOVED REDUCING COUPLINGS Model 105

Pipe Material• Carbon steel, Schedule 10, Schedule 40. For use with alternative materials and wall thicknesses please contact ARGCO.Maximum Working Pressure• Up to 300 psi/2517 kPa.Function• Joins carbon steel pipe.• Provides a rigid pipe joint designed to restrict axial or angular movement.CERTIFICATIONS/LISTINGSUnderwriters Laboratories, Underwriters Laboratories Canada, Factory Mutual.





The ARGCO Model 105 reducing coupling allows for direct reduction on a piping run and eliminates the need for a concentric reducer and couplings.The specially designed rubber gasket helpsprevent small pipe from telescoping into larger pipe during vertical assembly.

Caution: Model 105 couplings should not be used with an end cap, as the end may be sucked into the pipe when draining the system.

GROOVED REDUCING COUPLINGS Model 105


Bolt Size inches

mm3/8 x 2

M10 x 503/8 x 2-1/8M10 x 50

3/8 x 2-1/8M10 x 50

1/2 x 2-5/8M12 x 65

1/2 x 2-5/8M12 x 65 1/2

x 2-5/8M12 x 65 1/2

x 2-5/8M12 x 65 1/2

x 2-5/8M12 x 65

5/8 x 3-1/8M16 x 80

5/8 x 3-1/8M16 x 80

3/4 x 4-1/3M20 x 110

Item #7010109

7010111

7010112

7010113

7010114

7010115

7010116

7010117

7010118

7010119

7010120

NominalSize

in/mm1-1/2 x1-1/4

40 x 322 x 1-1/250 x 40

2-1/2 x 265 x 50

3 x 280 x 50

3 x 2-1/280 x 65

4 x 2100 x 504 x 2-1/2100 x 65

4 x 3100 x 80

5 x 4125 x 100

6 x 4150 x 100

8 x 6200 x 150

Max.Working Pressurepsi/Bar

30020

30020

30020

30020

30020

30020

30020

30020

30020

30020

30020

Max. End Load

Lbs/KN8523.7913275.9119458.66288512.84288512.84476921.22476921.22476921.22712431.70995044.271752477.97

AxialDisplacement

in/mm0.0625

1.60.0625

1.60.0625

1.60.0625

1.60.0625

1.60.125

3.20.125

3.20.125

3.20.125

3.20.125

3.20.125

3.2

Binches

mm4.451135.121305.941516.56

166.66.56

166.67.872007.872007.872009.25235

10.83275

13.23336

Dimensions

C inches

mm1.7745

1.8146

1.8146

1.8146

1.8146

1.9750

1.9750

1.9750

2.0552

2.0552

2.2858

Ainches

mm2.7670

3.2382

3.8297

4.411124.411125.551415.551415.58

141.86.651697.76197

10.08256

• Deflection or angular movement is the maximum value that a coupling allows under no internal pressure.• Working Pressure and End Load are total, from all internal and external loads, based on standard weight (ANSI) steel pipe, standard roll or cut grooved in accordance with ARGCO specifications. • The allowable pipe separation dimension shown is for system layout purposes only. ARGCO couplings are considere rigid connections and will not accommodate expansion or contraction of the piping system.

Pipein/ft

mm/m330.427

0.3222

0.2618

0.2218

0.2228

0.3428

0.3428

0.3423

0.2720

0.2415

0.18

Deflection

DegreePer

Coupling (°)1° - 54'1° - 54'1° - 31'1° - 31'1° - 15'1° - 15'1° - 02'1° - 02'1° - 02'1° - 02'1° - 36'1° - 36'1° - 36'1° - 36'1° - 36'1° - 36'1° - 18'1° - 18'1° - 07'1° - 07'1° - 50'1° - 50'

ActualO.D.

in/mm1.9 x 1.66948.3 x 42.42.375 x 1.960.3 x 48.3

2.875 x 2.37573 x 60.3

3.5 x 2.37588.9 x 60.33.5 x 2.87588.9 x 73.04.5 x 2.375

114.3 x 2.3754.5 x 2.875

114.3 x 73.04.5 x 3.5

114.3 x 88.95.5 x 4.5

139.7 x 114.36.625 x 4.5159 x 114.3

8.625 x 6.525219.1 x 168.3

ARGCO Grooved Couplings are suitable for fire protection systems, water supply sys-tems, and other process systems of higher working pressure.


GROOVED STANDARD RADIUS ELBOWSModels 201, 208, 205+, 207

Available Sizes• 1" through 12" (25 through 300 mm)

Pipe Material• Carbon steel, Schedule 10, Schedule 40. For use with alternative materials and wall thicknesses please contact ARGCO.

Maximum Working Pressure• Up to 300 psi/20 bar

Function• Joins carbon steel pipe.• Provides a rigid pipe joint designed to restrict axial or angular movement.

CERTIFICATIONS/LISTINGSUnderwriters Laboratories, Underwriters Laboratories Canada, Factory Mutual.



GROOVED STANDARD RADIUS ELBOWSModels 201, 208, 206, 207

Item #

7010041

7010042

7010043

7010044

7010045

7010046

7010047

7010048

7010049

7010050

7010051

NominalSize

in/mm1-1/4"

321-1/2"

402" 50

2-1/2" 653" 804"

1005"

1256"

1508"

20010"25012"300

C-Einches

mm2.7670

2.7670

3.2783

3.7495

4.25108

51275.511406.251657.761979.0222910

254

• Working Pressure and End Load are total, from all internal and external loads, based on standard weight (ANSI) steel pipe, standard roll or cut grooved in accordance with ARGCO specifications. • The allowable pipe separation dimension shown is for system layout purposes only. ARGCO couplings are considere rigid connections and will not accommodate expansion or contraction of the piping system.• When assembling ARGCO couplings onto end caps, take additional care to make certain the end cap is fully seated against the gasket end stop.

Model 20190° ElbowStandard

PipeO.D.

in/mm1.669 42.41.9

48.32.37560.3

2.875733.5

88.94.5

114.35.5133

6.625159

8.625219.110.75273

12.75323.9

Item #

7010062

7010063

7010064

7010065

7010066

7010067

7010068

7010069

7010070

7010071

7010072

C-Einches

mm1.7745

1.7745

2.0151

2.4462

2.7670

2.9976

3.2783

3.5089

4.251084.76121------

Item #

7010245

7010246

7010247

7010248

7010249

7010250

7010251

7010252

7010253

7010254

7010255

C-Einches

mm1.3835

1.3835

1.5038

1.5038

1.7745

1.7745

2.0151

2.0151

2.1354

2.2457------

Max WorkingPressurepsi/Bar

30020

30020

30020

30020

30020

30020

30020

30020

30020

30020

30020

Model 20845° Elbow

Model 20622.5° Elbow

Model 20711.25° Elbow

Item #

7010073

7010074

7010075

7010076

7010077

7010078

7010079

7010080

7010081

7010082

7010083

C-Einches

mm1.7745

1.8948

2.0151

2.0151

2.8773

2.8773

2.8773

3.1179

4.371114.88124------



GROOVED END OF RUN REDUCING ELBOW (ADACAP)MODEL 7091

Pipe Material• Carbon steel, Schedule 10, Schedule 40.


Function• Joins carbon steel pipe grooved pipe to threaded.

CERTIFICATIONS/LISTINGSUnderwriters Laboratories,Underwriters Laboratories Canada, Factory Mutual.

SPECIFICATIONS - MATERIALHousing Sections: Ductile Iron conforming toASTM A 536, Grade 65-45-12.


Ductile iron 90° grooved-end elbow with base support, designed for installation at the bottom of a riser system. An anchor can be placed in conjunction with the base to support the weight of the pipe, coupling and fluid.

Item #

7010260

7010261

7010262

7010263

7010264

7010265

7010266

7010267

7010268

NominalSize

in/mm1-1/4" x 1/2"

32 x 151-1/4" x 3/4"

32 x 201-1/4" x 1"

32 x 251-1/2" x 1/2"

40 x 151-1/2" x 3/4"

40 x 201-1/2" x 1"

40 x 252" x 1/2"50 x 152" x 3/4"50 x 202" x 1"50 x 25

C-Einches

mm2.4061

2.4061

2.4061

2.5264

2.5264

2.5264

2.5264

2.7670

2.7670

NPTBSP1/2"15

3/4"201"25

1/2"15

3/4"201"25

1/2"15

3/4"201"25


30020

30020

30020

30020

30020

30020

30020

30020

30020

GROOVED FITTINGS

MODEL XGQT014 90° REDUCING ELBOW

The Model XGQT014 is a duc le iron 90° grooved-end elbow with base support, designed for installa on at the bo om of a riser system. An anchor can be placed in conjunc on with the base to support the weight of the pipe, coupling and uid.

MODEL 900 END-ALL FITTING

The Model 900 End-All ng is a unique domed end cap ng available with 1/2’’, 3/4’’ and 1’’ NPT or BSP threaded outlets. Designed as an end of line ng the End-All features two mul -func on bosses which can be used for the direct connec on of sprinkler heads, sprigs, drops, drains and or gauges.

151/2203/4251

151/2203/4251

151/2203/4251

151/2203/4251

2030020

30020

30020

30020

30020

30020

30020

30020

30020

30020

30020

300

612.4061

2.4061

2.4064

2.5264

2.5264

2.5270

2.7670

2.7670

2.7676

2.9976

2.9976

2.99

32×1511/4×1/2

32×2011/4×3/4

32×2511/4×140×15

11/2×1/240×20

11/2×3/440×2511/2×150×152×1/250×202×3/450×25

2×165×15

21/2×1/265×20

21/2×3/465×2521/2×1

NominalSize

mm/inNPT/BSP C - E

mm/in

32×151.25×0.5

32×201.25×0.75

32×251.25×140×15

1.5×0.540×20

1.5×0.7540×251.5×150×152×0.550×202×0.7550×25

2×165×15

2.5×0.565×20

2.5×3/465×252.5×1

2030020

30020

30020

30020

30020

30020

30020

30020

30020

30020

30020

300

44.51.75044.5

1.75048.3

1.90044.5

1.75044.5

1.75048.3

1.90044.5

1.75044.5

1.75048.3

1.90044.5

1.75044.5

1.75048.3

1.900

30.11.19030.1

1.19031.8

1.25033.3

1.31333.3

1.31334.9

1.37539.7

1.56239.7

1.56241.3

1.62544.5

1.75044.5

1.75046.0

1.813

Nominal SizeGrooved X Threaded

mm/in

DimensionsA

mm/inB

mm/in



GROOVED SHORT RADIUS ELBOWS & TEESModels 301, 302









ARGCO short radius fittings, while primarily designed for fire protection applications, can also be used for general service requirements

GROOVED SHORT RADIUS ELBOWS & TEESModels 301, 302


Item #

7010032

7010033

7010034

7010035

7010036

7010037

7010038

NominalSize

in/mm2" 50

2-1/2" 653" 804"

1005"

1256"

1508"

200

C-Einches

mm2.7670

2.9976

3.3585

4.021024.761215.121305.12130

• Working Pressure and End Load are total, from all internal and external loads, based on standard weight (ANSI) steel pipe, standard roll or cut grooved in accordance with ARGCO specifications.

User Responsibility for Product Selection and SuitabilityEach user bears final responsibility for making a determination as to the suitability of ARGCO products for a particular end-use application, in accordance with industry stan-dards and project specifications, and the applicable building codes and related regulations as well as ARGCO performance, maintenance, safety, and warning instructions. Nothing in this or any other document, nor any verbal recommendation, advice, or opinion from any ARGCO employee, shall be deemed to alter, vary, supersede, or waive any provision of Allied Rubber and Gasket Company's standard conditions of sale, installation guide, or this disclaimer.NoteAll products to be installed in accordance with current ARGCO installation/assembly instructions. ARGCO reserves the right to change product specifications, designs and standard equipment without notice and without incurring obligations.InstallationReference should always be made to the ARGCO installation instructions of the product you are installing. WarrantyRefer to the Warranty section of the current Price List or contact ARGCO for details.

Model 30190° Elbow

Short

PipeO.D.

in/mm2.37560.3

2.875733.5

88.94.5

114.35.5

139.76.625168.38.625219.1

Item #

7010085

7010086

7010087

7010088

7010089

7010090

7010091

C-Einches

mm2.7670

2.9976

3.3585

4.021024.761215.121306.89175


30020

30020

30020

30020

30020

30020

30020

Model 302Tee Short

GROOVED DRAIN ELBOWModel 002D

Pipe Material• Carbon steel, Schedule 10, Schedule 40.



CERTIFICATIONS/LISTINGSUnderwriters Laboratories,Underwriters Laboratories Canada,Factory Mutual.



The Model 002D is a grooved-end ductile iron cast elbow with an integral 1’’ NPT drain. The 002D was primarily designed for, but not limited to, used on fire protection standpipes

NominalSize

in/mm2

502-1/2

653

804

1006

150

• Working Pressure is total, from all internal and external loads, based on standard weight (ANSI) steel pipe, standard roll or cut grooved in accordance with ARGCO specifications. • The allowable pipe separation dimension shown is for system layout purposes only. ARGCO couplings are considere rigid connections and will not accommodate expansion or contraction of the piping system.• When assembling ARGCO couplings onto end caps, take additional care to make certain the end cap is fully seated against the gasket end stop.

PipeO.D.

in/mm2.37560.3

2.875733.5

88.94.5

114.36.625168.3

Item #

7010054

7010055

7010056

7010057

7010058

Dimensions

C-Einches

mm3.2783

3.7495

4.251085.001276.50165

Dinches

mm2.7670

2.7670

2.7670

2.7670

2.7670

Einches

mm1.4837.51.7745

2.1755

2.7068.53.7695.5



GROOVED STANDARD RADIUS TEESModel 301









• Working Pressure and End Load are total, from all internal and external loads, based on standard weight (ANSI) steel pipe, standard roll or cut grooved in accordance with ARGCO specifications.

GROOVED STANDARD RADIUS TEESModel 301

Item #

7010092

7010093

7010094

7010095

7010096

7010097

7010098

7010099

7010100

7010101

7010102

NominalSize

in/mm1-1/4"

321-1/2"

402" 50

2-1/2" 653" 804"

1005"

1256"

1508"

20010"25012"300

C-Einches

mm2.7670

2.7670

3.3184

3.7495

4.251085.001275.511406.501657.761979.02229

10.00254

PipeO.D.

in/mm1.66942.41.9

48.32.37560.3

2.875733.5

88.94.5

114.35.5140

6.625168.58.625219.110.75273

12.75323.9


30020

30020

30020

30020

30020

30020

30020

30020

30020

30020

30020


GROOVED REDUCING TEES Model 303








GROOVED REDUCING TEES Model 303

Item #

7010501

7010502

7010511

7010512

7010513

7010519

7010520

7010523

7010524

7010525

7010526

7010528

7010534

7010537

7010538

7010539

7010541

NominalSize

in/mm2 x 1-1/250 x 40

2-1/2 x 1-1/465 x 32

4 x 2100 x 504 x 2-1/2100 x 65

4 x 3100 x 80

5 x 4125 x 100

6 x 2150 x 506 x 2-1/2150 x 65

6 x 3150 x 80

6 x 4150 x 100

6 x 5150 x 125

8 x 4200 x 100

8 x 6200 x 150

10 x 4250 x 100

10 x 6250 x 150

10 x 8250 x 200

12 x 8300 x 150

C-Einches

mm2.7670

2.9976

4.021024.021024.02 1024.13 1055.511405.511405.511405.511405.511406.851746.851747.481907.481907.481908.66220

PipeO.D.

in/mm2.375 x 1.960.3 x 48.3

2.875 x 1.66973 x 42.4

4.5 x 1.669114.3 x 42.4

4.5 x 1.9114.3 x 48.34.5 x 2.375

114.3 x 60.35.5 x 4.25

139.7 x 1086.25 x 3

159 x 76.16.25 x 3.5159 x 88.96.625 x 3150 x 8

6.625 x 4.5168.3 x 114.3

6.625 x 5.5168.3 x 139.7

8.625 x 4.5219.1 x 76.18.625 x 6.5

219.1 x 165.110.75 x 4.5273 x 114.310.75 x 6.5273 x 168.3

10.75 x 8.625273 x 219.1

10.75 x 8.625323.7 x 219.1


30020

30020

30020

30020

30020

30020

30020

30020

30020

30020

30020

30020

30020

30020

30020

30020

30020

C1-E1inches

mm2.7670

2.9976

4.021024.02 1024.02 1024.131055.511405.511405.511405.511405.511406.851746.851747.481907.481907.481908.66220

Dimensions


GROOVED END CAP, END CAP WITH HOLEModel 601, 602







ARGCO Model 602 End Cap with Hole is an ideal transition fitting when a large reduction isrequired such as 6’’×1’’, 4’’×1’’ etc. The Model 602 can be used as an alternave to expensive swaged nipples.

GROOVED END CAP, END CAP WITH HOLEModel 601, 602


NominalSize

in/mm1-1/4

321-1/2

402

502-1/2

653

804

1005

1256

1508

20010

25012

300

PipeO.D.

in/mm1.66942.41.9

48.32.37560.3

376.13.5

88.94.5

114.35.5

139.76.625168.38.625219.110.75273

12.75323.9

Item #

7010125

7010126

7010127

7010128

7010129

7010130

7010131

7010132

7010133

7010134

7010135


30020

30020

30020

30020

30020

30020

30020

30020

30020

30020

30020

E-Einches

mm0.942.380.942.380.942.380.942.380.942.381.0025.41.0025.41.0025.41.1930.21.1930.2 1.1930.2

NominalSize

in/mm2 x 1

50 x 25 2-1/2 x 165 x 25

3 x 180 x 25

4 x 1100 x 25

6 x 1150 x 25

8 x 1200 x 25

PipeO.D.

in/mm2.375 x 1.327

60.3 x 33.7 2.875 x 1.327

73 x 33.73.5 x 1.32788.9 x 33.74.5 x 1.327

114.3 x 33.76.625 x 1.327168.3 x 33.76.5 x 1.327

219.1 x 33.7

Item #

7010136A

7010136

7010137

7010138

7010140

7010141


30020

30020

30020

30020

30020

30020

E-Einches

mm0.9423.80.9423.80.9423.81.0025.41.0025.4

END CAP END CAP WITH HOLE


GROOVED CONCENTRIC REDUCERMODEL 701

Pipe Material• Carbon steel, Schedule 10, Schedule 40. For use with alternative materials and wall thicknesses please contact ARGCO.Maximum Working Pressure• Up to 300 psi/20 barFunction• Joins carbon grooved pipe system to flange components




GROOVED CONCENTRIC REDUCERMODEL 701

Item #

7010150

7010151

7010152

7010153

7010154

7010155

7010156

7010157

7010158

7010159

7010160

7010161

7010162

7010163

Nominal Sizein/mm

1-1/2" x 1-1/4"40 x 322" x 1"50 x 25

2" x 1-1/4"50 x 32

2" x 1-1/2"50 x 40

2-1/2" x 1-1/4"65 x 32

2-1/2" x 1-1/2"65 x 40

2-1/2" x 2"65 x 50

3" x 1-1/4"80 x 32

3" x 1-1/2"80 x 403" x 2"80 x 50

3" x 2-1/2"80 x 654" x 2"

100 x 504" x 2-1/2"100 x 654" x 3"

100 x 80

Pipe O.D.in/mm

1.9" x 1.669"48.3 x 42.4

2.375" x 1.669"60.3 x 42.42.375"x 1.9"60.3 x 48.3

2.875" x 1.669"73 x 42.4

2.875" x 1.9"73 x 48.3

2.875" x 2.375"73 60.3

3.5" x 1.669"88.9 x 42.4

3.5" x 88.9 x 48.3

3.5" x 2.375"88.9 x 60.33.5 x 2.875"

88.9 x 734.5" x 2.375"114.3 x 60.34.5" x 2.875"114.3 x 734.5" x 3.5"

114.3 x 88.9

Item #

7010164

7010165

7010166

7010168

7010169

7010170

7010172

7010173

7010174

7010176

7010177

7010179

7010180

7010181

Nominal Sizein/mm5" x 2"

125 x 505" x 3"

125 x 805" x 4"

125 x 1006" x 3"

6" x 4"150 x 100

6" x 5"150 x 125

8" x 4"200 x 100

8" x 5"200 x 125

8" x 6"200 x 15010" x 6"

250 x 15010" x 8"

250 x 20012" x 6"

300 x 15012" x 8"

300 x 20012" x 10"300 x 250

Pipe O.D.in/mm

5.25" x 2.375"133 x 60.35.5" x 3.5"

139.7 x 88.95.5" x 4.25"139.7 x 108

6.625" x 4.25"168.3 x 1086.625" x 5.5"168.3 x 139.78.625" x 4.5"219.1 x 114.38.625" x 5.5"219.1 x 139.78.625" x 6.25"219.1 x 159

10.75" x 6.25"273 x 159

10.75" x 8.625"273 x 219.1

12.75" x 6.25"323.9 x 159

12.75" x 8.63"323.9 x 219.1

12.75" x 10.75"323.9 x 273


E-Ein/mm2.5264

2.5264

2.5264

2.5264

2.5264

2.5264

2.5264

2.5264

2.5264

2.5264

2.5264

2.9976

2.9976

2.9976

E-Ein/mm3.3585

3.3585

3.3585

3.3585

3.3585

3.3585

3.3585

3.3585

3.3585

3.5490

3.5490

3.5490

3.5490

3.5490


THREADED CONCENTRIC REDUCERMODEL 702

Pipe Material• Carbon steel, Schedule 10, Schedule 40. For use with alternative materials and wall thicknesses please contact ARGCO.Maximum Working Pressure• Up to 250 psi/17 barFunction• Joins carbon grooved pipe system to flange components




ARGCO concentric reducers are cast ofductile iron. The end-to-end dimensions of these reducers are less than that of fabricated reducers.


THREADED CONCENTRIC REDUCERMODEL 702

Item #

7010182

7010183

7010184

7010185

7010186

7010187

7010188

7010189

7010190

7010191

7010192

7010193

7010194

7010195

7010196

7010197

Nominal Sizein/mm

1-1/4" x 1"

1-1/2" x 1-1/4"

2" x 1"

2" x 1-1/4"

2" x 1-1/2"50 x 40

2-1/2" x 1-1/4"65 x 32

2-1/2" x 1-1/2"65 x 40

2-1/2" x 2"65 x 503" x 1"80 x 25

3" x 1-1/4"80 x 32

3" x 1-1/2"80 x 403" x 2"80 x 50

3" x 2-1/2"80 x 654" x 1"

100 x 254" x 1-1/4"100 x 32

4" x 1-1/2"100 x 40

E - Ein/mm

2.2516

2.2516

2.2564

2.5264

2.5264

2.5264

2.5264

2.5264

2.5264

2.5264

2.5264

2.9976

2.9976

2.9976

Pipe O.D.

2.375" x 1.327"60.3 x 33.7

2.375" x 1.669"60.3 x 42.42.375" x 1.960.3 x 48.3

2.875" x 1.669"73 x 42.4

2.875" x 1.9"73 x 48.3

2.875" x 2.375"73 x 60.3

3.5" x 1.327"88.9 x 33.7

3.5" x 1.669"88.9 x 42.43.5" x 1.9" 88.9 x 48.3

3.5" x 2.375"88.9 x 60.3

3.5" x 3"88.9" x 76.14.5" x 1.327"114.3 x 33.74.5" x 1.669114.3 x 42.44.5" x 1.9"

114.3 x 48.3

Item #

7010198

7010199

7010200

7010201

7010202

7010203

7010204

7010205

7010206

7010207

7010208

7010209

7010210

7010211

7010212

7010213

Nominal Sizein/mm4" x 2"

100 x 504" x 3"

100 x 805" x 1-1/4"125 x 32

5" x 1-1/2"125 x 405" x 2"

125 x 505" x 3"

125 x 806" x 1-1/4"150 x 32

6" x 1-1/2"150 x 406" x 2"

150 x 506" x 2-1/2"150 x 656" x 3"

150 x 808" x 1"

200 x 258" x 1-1/4"200 x 32

8" x 1-1/2"200 x 408" x 2"

200 x 508" x 2-1/2"200 x 65

E-Ein/mm3.3585

3.3585

3.3585

3.3585

3.3585

3.3585

3.3585

3.3585

3.3585

3.3585

3.3585

3.3585

3.3585

3.3585

3.3585

3.3585

Pipe O.D.in/mm

4.5" x 2.375"114.3 x 60.34.5" x 3.5"

114.3 x 88.95.5" x 1.669"139.7 x 42.45.5" x 1.9"

139.7 x 48.35.5" x 2.375"139.7 x 60.35.5" x 3.5"

139.7 x 88.96.625" x 1.669"

168.3 x 42.46.625" x 1.9"168.3 x 48.3

6.625" x 2.375"168.3 x 60.36.625" x 3"

168.3 x 76.16.625" x 3.5"168.3 x 88.9

8.625" x 1.327"219.1 x 33.7

8.625" x 1.669"219.1 x 42.48.625" x 1.9"219.1 x 48.3

8.625" x 2.375"219.1 x 60.3

8.625" x 2.875"219.1 x 73

Max. WorkingPressurePSI/Bar

23016

23016

23016

23016

23016

23016

23016

23016

23016

23016

23016

23016

23016

23016


23016

23016

23016

23016

23016

23016

23016

23016

23016

23016

23016

23016

23016

23016

23016

23016


U-BOLT MECHANICAL TEE (SADDLE-LET)Model 501

Pipe Material• Carbon steel, Schedule 10, Schedule 40. For use with alternative materials and wall thicknesses please contact ARGCO.Maximum Working Pressure• Up to 300 psi/2517 kPa.Function• Joins carbon steel pipe.• Provides a rigid pipe joint designed to restrict axial or angular movement.CERTIFICATIONS/LISTINGSUnderwriters Laboratories, Underwriters Laboratories Canada, Factory Mutual.





The Model 300U Saddle-Lets is the ideal outlet fitting for direct connecons to sprinkler heads, drop nipples and or gauges. No need for welding, just cut or drill a hole at the desired outlet location. Posion the Saddle-Let so that the locating collar fits within the hole and secure with the U-bolt and nuts. The Saddle-Let allows full bore flow and is pressure rates to 300 psi (20 bar).

U-BOLT MECHANICAL TEE (SADDLE-LET)Model 501

Item #

7010285

7010286

7010287

7010288

7010289

7010290

7010291

7010292

7010293

7010294

7010295

7010296

Nominal Sizein/mm

1-1/4 x 1/235 x 15

1-1/4 x 3/432 x 20

1-1/4 x 132 x 25

1-1/2 x 1/240 x 15

1-1/2 x 3/440 x 20

1-1/2 x 140 x 252 x 1/250 x 152 x 3/450 x 20

2 x 150 x 25

2-1/2 x 1/265 x 15

2-1/2 x 3/465 x 20

2-1/2 x 165 x 25

Hole Dia. T +0.04, -0

+1, -01.1830

1.1830

1.1830

1.1830

1.1830

1.1830

1.1830

1.1830

1.1830

1.1830

1.1830

1.1830

Take-OutT/D

in/mm1.7344

1.7344

1.8547

1.8146

1.8146

1.9349

2.0953

2.0953

2.2056

2.2858

2.2858

2.4061

Binches

mm3.5089

3.5089

3.5089

3.5089

3.5089

3.5089

3.8698

3.8698

3.8698

4.371114.371114.37111

Dimensions

C inches

mm2.2056

2.2056

2.2056

2.2056

2.2056

2.2056

2.2056

2.2056

2.2056

2.2056

2.2056

2.2056

Ainches

mm2.0953

2.0953

2.2056

2.1755

2.1755

2.2858

2.5264

2.5264

2.6467

2.7269

2.7269

2.8372

Bolt Sizein

3/8U-Bolt

3/8U-Bolt

3/8U-Bolt

3/8U-Bolt

3/8U-Bolt

3/8U-Bolt

3/8U-Bolt

3/8U-Bolt

3/8U-Bolt

3/8U-Bolt

3/8U-Bolt

3/8U-Bolt

Bolt TorgueN-M/Lbs-Ft

22-2930-4022-2930-4022-2930-4022-2930-4022-2930-4022-2930-4022-2930-4022-2930-4022-2930-4022-2930-4022-2930-4022-2930-40



MECHANICAL TEE (THREAD)Model 403

Pipe Material• Carbon steel, Schedule 10, Schedule 40. For use with alternative materials and wall thicknesses please contact ARGCO.Maximum Working Pressure• Up to 300 psi/20 barFunction• Joins carbon steel pipe.• Provides a rigid pipe joint designed to restrict axial or angular movement.






The Model 302 Mechanical Tee provides a fast and easy mid-pipe threaded branch outlet. It elimi-nates the need for welding or mulple fittings. The mechanical tee utilizes ductile iron housings, a grade E moulded gasket and heat-treated carbon steel track bolts and nuts. Pressure rated to 300 psi (20 bar).


Item #

7010302

7010303

7010304

7010305

7010306

7010307

7010308

7010309

7010311

7010312

7010313

7010314

7010315

7010316

7010317

7010318

7010319

7010320

Nominal Sizein/mm2 x 3/450 x 20

2-1/2 x 3/465 x 20

2 x 150 x 25

2 x 1-1/450 x 32

2 x 1-1/250 x 40

2-1/2 x 165 x 25

2-1/2 x 1-1/465 x 32

2-1/2 x 1-1/265 x 40

3 x 180 x 25

3 x 1-1/480 x 32

3 x 1-1/280 x 40

3 x 280 x 50

4 x 1100 x 254 x 1-1/4100 x 324 x 1-12100 x 40

4 x 2100 x 504 x 2-1/2100 x 65

Continued on next page

Pipe O.D.

2.375 x 1.0560.3 x 26.7

2.875 x 1.0573 x 26.7

2.375 x 1.32760.3 x 33.7

2.375 x 1.66960.3 x 42.42.375 x 1.960.3 x 48.3

2.875 x 1.32773.0 x 33.7

2.875 x 1.66973.0 x 42.42.875 x 1.973.0 x 48.33.5 x 1.32788.9 x 33.73.5 x 1.66988.9 x 42.4

3.5 x 1.988.9 x 48.33.5 x 2.37588.9 x 60.34.5 x 1.327

114.3 x 33.74.5 x 1.669

114.3 x 42.44.5 x 1.9

114.3 x 48.3 4.5 x 2.375

114.3 x 60.34.5 x 3

114.3 x 76.1

Hole Dia. T +3.2,-0 /+0.13,-0

1.5038

1.5038

1.5038

1.7544.51.7544.51.5038

1.7544.52.0050.81.5038

1.7544.52.0050.82.5063.51.5038

1.8146

2.0953

2.5063.52.7670

Tt1.9750

2.0256

1.8547

2.0552

2.0552

2.0953

2.2858

2.2858

2.4061

2.5665

2.8071

2.7670

2.8773

3.0778

3.2783

3.2783

2.8773

A 2.20 56 2.42 61.5 2.20 56 2.68 68 2.80 71 4.42 61.5 2.89 73.5 2.89 73.5

2.74 69.5 3.19 81 3.19 81 3.19 81 2.99 76 2.99 76 2.99 76 3.07 78 4.13 105

B1.6542

1.8547

1.6542

1.6542

1.6542

1.8547

1.8547

1.8547

2.17 55

2.1755

2.1755

2.1755

2.4462

2.4462

2.4462

2.4462

2.4462

C4.721205.631434.721204.721204.721205.631435.631435.63143 6.221586.221586.221586.221586.571676.571676.571676.571676.57167

D2.9976

2.9976

2.9976

3.3184

3.3784

2.9976

3.3184

3.5490

2.9976

3.3184

3.5490

3.981012.9976

3.2783

3.5490

3.941004.61117

Bolt Sizein/mm

3/8 x 2-3/8 M 10 x 601/2 x 2-5/8 M 12 x 653/8 x 2-3/8 M 10 x 603/8 x 2-3/8 M 10 x 603/8 x 2-3/8 M 10 x 601/2 x 2-5/8 M 12 x 651/2 x 2-5/8 M 12 x 651/2 x 2-5/8 M 12 x 651/2 x 2-5/8 M 12 x 651/2 x 2-5/8 M 12 x 651/2 x 2-5/8 M 12 x 651/2 x 2-5/8 M 12 x 651/2 x 2-5/8 M 12 x 651/2 x 2-5/8 M 12 x 651/2 x 2-5/8 M 12 x 651/2 x 2-5/8 M 12 x 651/2 x 2-5/8 M 12 x 65


Dimensions - in/mm



Item #

7010321

7010322

7010323

7010324

7010325

7010326

7010327

7010328

7010329

7010330

7010331

7010332

7010333

7010334

7010335

7010336

7010337

7010338

7010339

Nominal Sizein/mm4 x 3

100 x 805 x 1

125 x 255 x 1-1/4125 x 325 x 1-1/2125 x 40

5 x 2125 x 505x 2-1/2125 x 65

5 x 3125 x 80

6 x 1150 x 256 x 1-1/4150 x 326 x 1-1/2150 x 40

6 x 2150 x 506 x 2-1/2150 x 65

6 x 3150 x 80

8 x 1200 x 258 x 1-1/4200 x 328 x 1-1/2200 x 40

8 x 2200 x 508 x 2-1/2200 x 65

8 x 3200 x 80

Pipe O.D.

4.5 x 3.5114.3 x 88.9

5.250 x 1.327133.0 x 33.75.5 x 1.669

139.7 x 42.45.5 x 1.9

139.7 x 48.35.5 x 2.375

139.7 x 60.35.5 x 3

139.7 x 76.15.5 x 3.5

139.7 x 88.96.625 x 1.327168.3 x 33.7

6.625 x 1.669168.3 x 42.46.625 x 1.9

168.3 x 48.36.625 x 2.375168.3 x 60.3

6.625 x 3168.3 x 76.16.625 x 3.5

168.3 x 88.98.625 x 1.327219.1 x 33.7

8.625 x 1.669219.9 x 42.48.625 x 1.9

219.1 x 48.38.625 x 2.375219.1 x 60.3

8.625 x 3219.1 x 76.18.625 x 3.5

219.1 x 88.9

Hole Dia. T +3.2,-0 /+0.13,-0 3.50 89 1.50 38 1.81 46 2.09 53 2.52 64 3.15 80 3.62 92 1.50 38 1.81 46 2.09 53 2.52 64 3.15 80 3.62 92 1.50 38 1.75 44.5 2.00 50.8 2.50 63.5 2.76 70 3.50 89

Dimensions - in/mm

Tt 3.31 84 3.35 85 3.54 90 3.74 95 3.74 95 3.82 97 4.17 106 4.45 113 4.45 113 4.41 112 4.37 111 4.37 111 4.33 110 5.98 152 5.98 152 5.98 152 5.43 138 5.08 129 5.31 135

A 3.94 100 3.50 89 3.50 89 3.50 89 3.50 89 3.62 92 3.70 94 4.00 101.5 4.00 101.5 4.00 101.5 4.00 101.5 4.15 105.5 4.15 105.5 5.35 136 5.79 147 5.79 147 5.79 147 6.14 156 6.24 158.5

B 2.56 65 2.91 74 2.91 74 2.91 74 2.91 74 2.91 74 2.91 74 3.58 91 3.58 91 3.58 91 3.58 91 3.58 91 3.58 91 1.92 125 1.92 125 1.92 125 1.92 125 1.92 125 1.92 125

C 7.13 181 8.07 205 8.07 205 8.07 205 8.07 205 8.07 205 8.07 205 9.17 233 9.17 233 9.17 233 9.17 233 9.17 233 9.17 233 12.68 322 12.68 322 12.68 322 12.68 322 12.68 322 12.68 322

D 5.35 136 2.99 76 3.27 83 3.54 90 3.94 100 4.61 117 5.08 129 2.99 76 3.27 83 3.54 90 3.94 100 4.61 117 5.08 129 2.99 76 3.31 84 3.54 90 3.98 101 4.61 117 136 5.35

Bolt Size in/mm 1/2 x 2-3/4 M 12 x 70 1/2 x 3 M 12 x 75 1/2 x 3 M 12 x 75 1/2 x 3 M 12 x 75 1/2 x 3 M 12 x 75 1/2 x 3 M 12 x 75 1/2 x 3 M 12 x 75 9/16 x 3 M 14 x 75 1/2 x 3 M 12 x 75 1/2 x 3 M 12 x 75 1/2 x 3 M 12 x 755/8 x 3-1/3 M 16 x 855/8 x 3-1/3 M 16 x 855/8 x 3-1/2 M 20 x 905/8 x 3-1/2 M 20 x 905/8 x 3-1/2 M 20 x 905/8 x 3-1/2 M 20 x 905/8 x 3-1/2 M 20 x 905/8 x 3-1/2 M 20 x 90


SADDLE-LET SMALL MECHANICAL TEE (THREAD)Model 502

Pipe Material• Carbon steel, Schedule 10, Schedule 40. For use with alternative materials and wall thicknesses please contact ARGCO.Maximum Working Pressure• Up to 300 psi/20 barFunction• Joins carbon steel pipe.• Provides a rigid pipe joint designed to restrict axial or angular movement.CERTIFICATIONS/LISTINGSUnderwriters Laboratories, Underwriters Laboratories Canada, Factory Mutual.





The Model 502 Saddle-Lets is the ideal outletfitting for direct connections to sprinkler heads, drop nipples and or gauges. No need for welding, just cut or drill a hole at the desired outlet location.Position the Saddle-Let so that the locating collar fits within the hole and secure with the U-bolt and nuts. The Saddle-Let allows full bore flow and is pres-sure rates to 300 psi (20 bar).


SADDLE-LET SMALL MECHANICAL TEE (THREAD)Model 502

Item #

7010300100050

7010300125050

7010300125075

7010300125100

7010300150050

7010300150075

7010300150100

7010300200050

7010300200075

7010300200100

7010300250005

7010300250075

7010300250100

Nominal Sizein/mm1 x 1/225 x 15

1-1/4 x 1/235 x 15

1-1/4 x 3/432 x 20

1-1/4 x 132 x 25

1-1/2 x 1/240 x 15

1-1/2 x 3/440 x 20

1-1/2 x 140 x 252 x 1/250 x 152 x 3/450 x 20

2 x 150 x 25

2-1/2 x 1/265 x 15

2-1/2 x 3/465 x 20

2-1/2 x 165 x 25

Hole Dia. T +0.04, -0

+1, -00.9524

1.1830

1.1830

1.1830

1.1830

1.1830

1.1830

1.1830

1.1830

1.1830

1.1830

1.1830

1.1830

Take-OutT/D

in/mm1.1429

1.3033

1.2832.51.5238.61.4236.11.4035.61.6441.71.6642.21.6441.71.8847.81.9148.51.8948

2.1354.1

Binches

mm3.6693

3.8698

3.8698

3.8698

3.8698

3.8698

3.8698

3.8698

3.8698

3.8698

3.8698

3.8698

3.8698

Dimensions

C inches

mm1.8948

2.5665

2.5665

2.2056

2.2056

2.2056

2.2056

2.2056

2.2056

2.2056

2.2056

2.2056

2.2056

Ainches

mm1.1028

1.7745

1.7745

2.1354

1.8948

1.8948

2.2457

2.1354

2.1354

2.4462

2.4061

2.4061

2.8071

Bolt Sizein

3/8

3/8

3/8

3/8

3/8

3/8

3/8

3/8

3/8

3/8

3/8

3/8

3/8

Bolt TorqueN-M/Lbs-Ft

22-2930-40 22-2930-4022-2930-4022-2930-4022-2930-4022-2930-4022-2930-4022-2930-4022-2930-4022-2930-4022-2930-4022-2930-4022-2930-40

Pipe Material• Carbon steel, Schedule 10, Schedule 40. For use with alternative materials and wall thicknesses please contact ARGCO.Maximum Working Pressure• Up to 300 psi/20 barFunction• Joins carbon steel pipe.• Provides a rigid pipe joint designed to restrict axial or angular movement.CERTIFICATIONS/LISTINGSUnderwriters Laboratories, Underwriters Laboratories Canada, Factory Mutual.





MECHANICAL TEE (GROOVE)Model 402

The Model 301 Mechanical Tee provides a fast and easy mid-pipe grooved branch outlet. The me-chanical tee utilizes ductile iron housings, a grade E gasket and heat-treated carbon steel track bolts and nuts. Maximum working pressure: 300 psi (20 bar).


Item #

7010415

7010416

7010417

7010418

7010420

7010421

7010422

7010423

7010424

7010425

7010426

7010427

7010428

7010429

7010430

7010431

7010432

7010433

Nominal Sizein/mm

2 x 1-1/450 x 32

2 x 1-1/250 x 40

2-1/2 x 1-1/465 x 32

2-1/2 x 1-1/265 x 40

3 x 1-1/480 x 32

3 x 1-1/280 x 40

3 x 280 x 50

4 x 1-1/4100 x 324 x 1-1/2100 x 40

4 x 2100 x 504 x 2-1/2100 x 65

4 x 3100 x 805 x 1-1/4125 x 325 x 1-1/2125 x 40

5 x 2125 x 505 x 2-1/2125 x 65

5 x 3 125 x 806 x 1-1/4150 x 32

Continued on next page

Pipe O.D.

2.375 x 1.66960.3 x 42.42.375 x 1.960.3 x 42.4

2.875 x 1.66973 x 42.4

2.875 x 1.973 x 48.3

3.5 x 1.66988.9 x 42.4

3.5 x 1.988.9 x 48.33.5 x 2.37588.9 x 60.34.5 x 1.669

114.3 x 42.44.5 x 1.9

114.3 x 48.34.5 x 2.375

114.3 x 60.34.5 x 3

114.3 x 76.14.5 x 3.5

114.3 x 88.95.5 x 1.669

139.7 x 42.45.5 x 1.9

139.7 x 48.35.5 x 2.375

139.7 x 60.35.5 x 3

139.7 x 76.15.5 x 3.5

139.7 x 88.96.625 x 1.669168.3 x 42.4

Hole Dia. T +3.2,-0

/+0.13,-0 1.75 44.5 1.75 44.5 1.75 44.5 2.00 50.8

1.72 44.5 2.00 50.8 2.50 63.5

1.75 44.5 2.00 50.8 2.52 64

3.15 80

3.50 89

1.75 44.5 2.09 53

2.52 64

3.15 80

3.62 92

1.75 44.5

Dimensions - in/mm

Bolt Size in/mm 3/8 x 2-3/8 M 10 x 603/8 x 2-3/8 M 10 x 601/2 x 2-5/8 M 12 x 651/2 x 2-5/8 M 12 x 651/2 x 2-5/8 M 12 x 651/2 x 2-5/8 M 12 x 651/2 x 2-5/8 M 12 x 651/2 x 2-3/4M 12 x 701/2 x 2-3/4 M 12 x 701/2 x 2-5/8 M 12 x 651/2 x 2-5/8 M 12 x 651/2 x 2-3/4 M 12 x 705/8 x 3-1/3 M 16 x 85 1/2 x 2 M 12 x 75 1/2 x 2 M 12 x 75 1/2 x 2 M 12 x 75 1/2 x 2 M 12 x 75 9/16 x 3 M 14 x 75

A 2.85 72.5 2.85 72.5 3.09 78.5 3.09 78.5 3.39 86 3.39 86 3.43 87 3.90 99 3.90 99 3.64 92.5 3.64 92.5 3.90 99 4.41 112 4.15 105.5 4.15 105.5 4.15 105.5 4.15 105.5 4.92 125

B 1.65 42 1.65 42 1.85 47 1.85 47 2.17 55 2.17 55 2.17 55 2.56 65 2.56 65 2.44 62 2.44 62 2.56 65 2.91 74 2.91 74 2.91 74 2.91 74 2.91 74 3.7 94

C 4.72 120 4.72 120 5.63 143 5.63 143 6.22 158 6.22 158 6.22 158 7.13 181 7.13 181 6.77 172 6.77 172 7.13 181 8.62 219 8.07 205 8.07 205 8.07 205 8.07 205 9.76 248

D 3.31 84 3.31 84 3.31 84 3.54 90 3.31 84 3.54 90 3.98 101 3.31 84 3.54 90 3.54 90 4.21 107 5.35 136 3.31 84 3.54 90 3.94 100 4.61 117 5.08 129 3.31 84

MECHANICAL TEE (GROOVE )Model 402


Item #

7010436

7010437

7010438

7010439

7010440

7010443

7010444

7010445

7010446

Pipe O.D.

6.625 x 1.9168.3 x 48.3

6.625 x 2.375168.3 x 60.3

6.625 x 3 168.3 x 76.16.625 x 3.5

168.3 x 88.96.625 x 4.25

165.1 x 108.08.625 x 2.375219.1 x 60.3

8.625 x 2.875219.1 x 60.38.625 x 3.5

219.1 x 88.98.625 x 4.25219.1 x 108

Hole Dia. T+3.2,-0

/+0.13,-02.0050.8 2.5264

3.1580

3.6292

4.091042.5063.52.7670

3.5089

4.49114

Dimensions - in/mm

Bolt Size in/mm

5/8 x 3-1/3 M 16 x 85 9/16 x 3 M 14 x 75 9/16 x 3 M 14 x 75 9/16 x 3 M 14 x 75 9/16 x 3 M 14 x 755/8 x 3-1/2 M 20 x 905/8 x 3-1/2 M 20 x 905/8 x 3-1/2 M 20 x 905/8 x 3-1/2 M 20 x 90

Nominal Sizein/mm

6 x 1-1/2150 x 40

6 x 2150 x 506 x 2-1/2150 x 65

6 x 3150 x 80

6 x 4150 x 100

8 x 2200 x 508 x 2-1/2200 x 65

8 x 3200 x 80

8 x 4200 x 100

A4.921254.651184.651184.651184.70

119.55.981526.061546.061546.14156

B3.794

3.5891

3.5891

3.5891

3.5891

1.921251.921251.921251.92125

C9.762489.712339.172339.172339.17233

12.68322

12.68322

12.68322

12.68322

D3.5490

3.941004.611175.081295.63143

3.98 1014.611175.351366.38162

MECHANICAL TEE (GROOVE)Model 402


FLANGE ADAPTERModel 902

The Model 902 Flange Adapter allows for direct connection of a grooved system to ANSI class 125/150 flanged components

Item #

7010450

7010451

7010452

7010453

7010454

7010455

7010456

7010457

7010458

Nominal Sizein/mm

250

2-1/2653

804

1005

1256

1508

20010

25012

300

Max. EndLoad

Lbs./KN13305.7119508.37288012.41477020.51739031.351034044.471752075.3727210164.7138280164.71

Binches

mm4.74

120.55.511406.021537.521918.502169.49241

11.77299

14.25362

17.01432

C inches

mm0.9825

0.9825

0.9825

0.9825

0.9825

0.9825

1.0627

1.1830

1.2632

Ainches

mm6.101557.091807.481909.06230

10.04255

11.02280

13.58345

15.94405

19.09485

Bolt HolesNo.44448888888888

12121212

Bolt Sizein/mm

5/8M165/8M165/8M165/8M163/4M203/4M203/4M20

1M24

1M24


2.87573.0

3.50088.9

4.500114.35.563141.36.625168.38.625219.1

10.750237.012.75323.9


25017

25017

25017

25017

25017

25017

25017

25017

25017

D inches

mm2.3660

2.8773

3.5089

4.491145.551416.611688.62219

10.75273

12.76324

E inches

mm3.0778

3.6693

4.211075.161316.181577.281859.21234

11.57294

13.43341


SPECIFICATIONS - MATERIALHousing Sections: Ductile Ironconforming to ASTM A 536, Grade 65-45-12.


Bolts and NutsStandard: Carbon Steel oval neck track bolts meeing ASTM A449 and ISO 898-1. Carbon steel hex nuts meet ASTM A563 Grade B.Nuts and Bolts are zinc electroplated per ASTM B633 NZ/FE5, finish Type III.

Pipe Material• Carbon steel, Schedule 10, Schedule 40. Maximum Working Pressure• Up to 300 psi/20 barFunction• Joins carbon grooved pipe system to flange components



FLANGE ADAPTER NIPPLEModel 802

The Model 902 Flange Adapter Nipple provides a rigid transition from a flanged component to a grooved system.

Pipe Material• Carbon steel, Schedule 10, Schedule 40. Maximum Working Pressure• Up to 300 psi/20\ barFunction• Joins carbon grooved pipe system to flange components


SPECIFICATIONS - MATERIALHousing Sections: Ductile Ironconforming to ASTM A 536, Grade 65-45-12.


Item #

7010630

7010631

7010632

7010633

7010634

7010635

7010636

7010637

Nominal Sizein/mm

250

2-1/2653

804

1005

1256

1508

20010

25012

300

Yinches

mm4.74

120.55.511406.021537.521918.502169.49241

11.77299

14.25362

17.01432

Dimensions

Z inches

mm0.6316

0.6316

0.7118

0.8722

0.8722

0.8722

0.9825

1.0226

1.1028

Xinches

mm6.101557.091807.481909.06230

10.04255

11.02280

13.58345

15.94405

19.09485

Bolt HolesNo.44444488888888

12121212

Bolt Sizein/mm

5/8M165/8M165/8M165/8M163/4M203/4M203/4M20

1M24

1M24


2.87573.03.50

88.904.50

114.305.563141.36.625

168.308.625219.110.75273

12.75323.9


30020

30020

30020

30020

30020

30020

30020

30020

30020

L inches

mm2.5665

2.5665

2.6565

2.7670

2.7670

2.7670

3.1580

3.3585

3.5490


GROOVED BUTTERFLY VALVE WITH TAMPER SWITCHModel BFLY-G300

• Design Standard: API609• Connection Ends: Groove to AWWA C606• Top Flange Standard: ISO 5211 Stem drive by keys, parallel or diagonal square of flat head• Working Pressure: 300 PSI • Temperature Range: 32° to 176° F• Coating: Fusion Bonded Epoxy Coating in accordance with ANSI/AWWA

WIRING DIAGRAM:

SUPERVISORY SWITCHWHITE (COM)

AUXILIARY SWITCH

ACTUATOR CASE GROUND

YELLOW x 2 Valve Open

RED x 2 Valve Not Open

BLACK (COM)BLUE x 2 Valve Open

ORANGE x 2 Valve Not Open

GREEN

Available Sizes2-1/2" through 10" (65/254 mm)Smaller sizes available in bronze construction.

Designed for Fire Protection Services Only

Weatherproof actuator housing approved for indoor and outdoor use.


SPECIFICATIONS: MATERIAL1. Upper Shaft Sealing Nut2. Shaft (Stem) Seal: EPDM3. Body: Ductile Iron conforming to ASTM A-536, Grade 65-45-124. Upper Shaft (Stem): 416 stainless steel conforming to ASTM A-5825. Disc: Ductile Iron conforming to ASTM A-536, Grade 65-45-12, with EPDM Coating6. Lower Shaft (Stem): 416 stainless steel conforming to ASTM A-5827. Lower Shaft (Stem) Sealing Nut: WCB conforming to ASTM A-2168. Stem Bushing: PTFE conforming to ASTM A-48949. O-Ring (Seat): Grade “E” EPDM conforming to ASTM D-200010. Gear Box

GROOVED BUTTERFLY VALVE WITH TAMPER SWITCHModel BFLY-G300

E

2.722.85

Item #

6520250

6520251

6520252

6520253

6520254

6520255

Size

2-1/2”

3”

4”

6”

8”

10”

A

4.92

5.51

6.3

7.48

9.06

10.2

B

3.74

3.94

3.94

5.51

6.89

7.87

C

1.26

1.26

1.26

1.26

1.26

1.77

3.5 3.34

4.334.5

6.5 6.33

10.53 10.56

8.52 8.33

6.63 6.46

10.75 12.32

8.63 8.46

D

2.873

F

0.63

0.63

0.63

0.63

0.75

0.75

G

0.31

0.31

0.31

0.37

0.44

0.5

H

4.37

4.37

4.37

4.37

4.96

4.96

J

5.98

5.98

5.98

7.87

11.4

11.4

P

3.54

3.54

3.54

3.54

4.92

4.92

M

2.76

2.76

2.76

2.76

4.02

4.02

N

0.35

0.35

0.35

0.35

0.47

0.47

D

0.39

0.39

0.43

0.63

0.75

0.87

L

3.8

3.82

4.53

5.21

5.8

6.26


MATERIAL SPECIFICATION PART NO. Description Material Specification Options

1 Valve Body Ductile Iron ASTM A536,65-45-12

2 Hinge Pin Stainless steel 420

3 Spring Stainless steel 304 Stainless steel 316 4 Spring Washer Stainless steel 304 5 Eye Bolt Carbon Steel Zinc Plated

6 Disc ≤4":Stainless steel 304

6"-12":Ductile Iron ASTM A536,65-45-12

7 Seal Ring EPDM ASTM D2000

8 Seat Bronze ASTM B62 C83600 Stainless steel 304/316 , Pressed Fit or Threaded

9 Plug Malleable Iron Galvanized 10 Bushing ≥8" ASTM B62 C26800

Note:For special material request other than standard specification,please indicate clearly on the inquiry or order list.

DRAWN BY: Cindy Zhang

DRAWING #: JMH84X Grooved Resilient Swing Check Valve

Series NO.:JMH84X 2”-12” CHECKED BY:

KINGER INDUSTRY INC.

REV.00.

APPROVED BY: Meng Xiang

ISSUE DATE 170313

• Connection Ends: Groove to AWWA C606 • Working Pressure: 300PSI 200PSI and 250PSI available upon request • Temperature Range: 0℃- 80℃• Coating: Fusion Bonded Epoxy Coating in accordance with ANSI/AWWA C550 or painting upon request

DN

Dimensions(IN)

L D1 D2 B C P1 P2P3

Standard Optional

2" 6.73 2.25 2.37 0.31 0.625 1/2-14NPT 3/8-18NPT 1/2-14NPT 1-11.5NPT

2.5" 7.24 2.72 2.87 0.31 0.625 1/2-14NPT 3/8-18NPT 1/2-14NPT 1 1/4-11.5NPT

3" 7.76 3.34 3.5 0.31 0.625 1/2-14NPT 3/8-18NPT 1/2-14NPT 1 1/4-11.5NPT

4" 8.27 4.33 4.5 0.38 0.625 1/2-14NPT 1/2-14NPT 1/2-14NPT 2-11.5NPT

5" 9.76 5.39 5.56 0.38 0.625 1/2-14NPT 1/2-14NPT 1/2-14NPT 2-11.5NPT

6" 12.76 6.46 6.63 0.38 0.625 1/2-14NPT 1/2-14NPT 1/2-14NPT 2-11.5NPT

8" 14.61 8.44 8.63 0.44 0.75 1/2-14NPT 1/2-14NPT 1/2-14NPT 2-11.5NPT

10" 17.99 10.56 10.75 0.5 0.75 1/2-14NPT 1/2-14NPT 1/2-14NPT 2-11.5NPT

12" 21.06 12.53 12.75 0.5 0.75 1/2-14NPT 1/2-14NPT 1/2-14NPT 2-11.5NPT















REV.00.


ISSUE DATE 170313


DN

Dimensions(IN)

L D1 D2 B C P1 P2P3

Standard Optional

2" 6.73 2.25 2.37 0.31 0.625 1/2-14NPT 3/8-18NPT 1/2-14NPT 1-11.5NPT

2.5" 7.24 2.72 2.87 0.31 0.625 1/2-14NPT 3/8-18NPT 1/2-14NPT 1 1/4-11.5NPT

3" 7.76 3.34 3.5 0.31 0.625 1/2-14NPT 3/8-18NPT 1/2-14NPT 1 1/4-11.5NPT

4" 8.27 4.33 4.5 0.38 0.625 1/2-14NPT 1/2-14NPT 1/2-14NPT 2-11.5NPT

5" 9.76 5.39 5.56 0.38 0.625 1/2-14NPT 1/2-14NPT 1/2-14NPT 2-11.5NPT

6" 12.76 6.46 6.63 0.38 0.625 1/2-14NPT 1/2-14NPT 1/2-14NPT 2-11.5NPT

8" 14.61 8.44 8.63 0.44 0.75 1/2-14NPT 1/2-14NPT 1/2-14NPT 2-11.5NPT

10" 17.99 10.56 10.75 0.5 0.75 1/2-14NPT 1/2-14NPT 1/2-14NPT 2-11.5NPT

12" 21.06 12.53 12.75 0.5 0.75 1/2-14NPT 1/2-14NPT 1/2-14NPT 2-11.5NPT















REV.00.


ISSUE DATE 170313


DN

Dimensions(IN)

L D1 D2 B C P1 P2P3

Standard Optional

2" 6.73 2.25 2.37 0.31 0.625 1/2-14NPT 3/8-18NPT 1/2-14NPT 1-11.5NPT

2.5" 7.24 2.72 2.87 0.31 0.625 1/2-14NPT 3/8-18NPT 1/2-14NPT 1 1/4-11.5NPT

3" 7.76 3.34 3.5 0.31 0.625 1/2-14NPT 3/8-18NPT 1/2-14NPT 1 1/4-11.5NPT

4" 8.27 4.33 4.5 0.38 0.625 1/2-14NPT 1/2-14NPT 1/2-14NPT 2-11.5NPT

5" 9.76 5.39 5.56 0.38 0.625 1/2-14NPT 1/2-14NPT 1/2-14NPT 2-11.5NPT

6" 12.76 6.46 6.63 0.38 0.625 1/2-14NPT 1/2-14NPT 1/2-14NPT 2-11.5NPT

8" 14.61 8.44 8.63 0.44 0.75 1/2-14NPT 1/2-14NPT 1/2-14NPT 2-11.5NPT

10" 17.99 10.56 10.75 0.5 0.75 1/2-14NPT 1/2-14NPT 1/2-14NPT 2-11.5NPT

12" 21.06 12.53 12.75 0.5 0.75 1/2-14NPT 1/2-14NPT 1/2-14NPT 2-11.5NPT















REV.00.


ISSUE DATE 170313


DN

Dimensions(IN)

L D1 D2 B C P1 P2P3

Standard Optional

2" 6.73 2.25 2.37 0.31 0.625 1/2-14NPT 3/8-18NPT 1/2-14NPT 1-11.5NPT

2.5" 7.24 2.72 2.87 0.31 0.625 1/2-14NPT 3/8-18NPT 1/2-14NPT 1 1/4-11.5NPT

3" 7.76 3.34 3.5 0.31 0.625 1/2-14NPT 3/8-18NPT 1/2-14NPT 1 1/4-11.5NPT

4" 8.27 4.33 4.5 0.38 0.625 1/2-14NPT 1/2-14NPT 1/2-14NPT 2-11.5NPT

5" 9.76 5.39 5.56 0.38 0.625 1/2-14NPT 1/2-14NPT 1/2-14NPT 2-11.5NPT

6" 12.76 6.46 6.63 0.38 0.625 1/2-14NPT 1/2-14NPT 1/2-14NPT 2-11.5NPT

8" 14.61 8.44 8.63 0.44 0.75 1/2-14NPT 1/2-14NPT 1/2-14NPT 2-11.5NPT

10" 17.99 10.56 10.75 0.5 0.75 1/2-14NPT 1/2-14NPT 1/2-14NPT 2-11.5NPT

12" 21.06 12.53 12.75 0.5 0.75 1/2-14NPT 1/2-14NPT 1/2-14NPT 2-11.5NPT

• Available Sizes: 2" through 8" • Connection Ends: Groove to AWWA C606• Working Pressure: 300 PSI • Temperature Range: 32° to 176° F• Coating: Fusion Bonded Epoxy Coating in accordance with ANSI/AWWA • Designed for Fire Protection Systems• Prevents Backflow• Single-disc mechanism incorporates a spring-assisted feature for non-slamming operation.• Can be installed either vertically (flow upwards only) or horizontally.• Valve body cast with arrow indicator to assist with proper orientation.• Provided with grooved ends.• Rated for ambient temperature use in fire protection systems.

SPECIFICATIONS: MATERIAL1. Valve Body2. Hinge Pin: 420 stainless steel conforming to ASTM A-5823. Spring: 304 stainless steel conforming to ASTM A-5824. Spring Washer: 304 stainless steel conforming to ASTM A-5825. Eye Bolt: Carbon Steel Zinc Plated6. Disc: 2” to 4” 304 stainless steel 2” to 4” Ductile Iron ASTM A536, 65-45-127. Seal Ring: Grade “E” EPDM conforming to ASTM D-20008. Seat: Bronze conforming to ASTM B-62-36009. Plug: Malleable Iron Galvanized10. Bushing: ASTM B-62-3600

GROOVED CHECK VALVEDUCTILE IRON

Item #

6520200

6520201

6520202

6520203

6520204

6520205

NominalSize

2"

2-1/2"

3"

4"

6"

8"

D1

2.25"

2.72"

3.34"

4.33"

6.46"

8.44"

D2

2.37"

2.87"

3.50"

4.50"

6.63"

8.63"

B

0.31"

0.31"

0.31"

0.38"

0.38"

0.44"

C

0.625"

0.625"

0.625"

0.625"

0.625"

0.750"

P3inches

1/2-14NPT

1/2-14NPT

1/2-14NPT

1/2-14NPT

1/2-14NPT

1/2-14NPT

P1inches

1/2-14NPT

1/2-14NPT

1/2-14NPT

1/2-14NPT

1/2-14NPT

1/2-14NPT

TakeoutL

6.73"

7.24"

7.76"

8.27"

12.76"

14.875"


BRASS BUTTERFLY VALVES • SLOW CLOSE • 300 PSITHREADED & GROOVED

Brecco Distribution Corp.77 N. 45th Avenue Ste #1 Phoenix, AZ. 85043

P: (800)543-4194 F: (602)484-9248

Sprinkler Control Valve for indoor and Outdoor Use.Brass body, chrome plated brass disc, and 300 PSI/20.7 Bar.UL Listed/FM Approved.Available threaded in sizes 1" to 2-1/2" complete with position indicator and integral Tamper Switch

SPECIFICATIONS: MATERIAL1. Valve Body: Bronze ASTM 584 C836002. Disc: 304 stainless steel3. Hand Wheel: ASTM 216 WCB7. 4. Seat: ASTM D-2000 Viton5. Indicator: Powder Metal FD0205 95HT6. Housing: Forged Brass JIS C37717. Cover: Forged Brass JIS C3771

Note: Packing Gland with Adjustable Glands shall be accessible for tightening stem seals without the disassembly of the valve or operator parts

Item #

6520290

6520291

6520292

6520293

6520295

Size

1"

1-1/4"

1-1/2"

2"

2-1/2"

A

2.13"

2.63"

2.87"

3.25"

4.49"

H

4.94"

5.13"

5.59"

6.13"

6.58"

L

1.56"

1.94"

2.19"

2.76"

3.41"

M

1.75"

2.17"

2.37"

3.11"

3.75"

Item #

6520291A

6520292A

6520294

6520296

Size

1-1/4"

1-1/2"

2"

2-1/2"

A

3.86"

4.02"

4.09"

4.49"

H

5.20"

5.47"

6.07"

6.58"

L

1.67"

1.90"

2.37"

2.87"

M

1.54"

1.78"

2.25"

2.72"

P

0.63"

0.63"

0.63"

0.63"

O

0.31"

0.31"

0.31"

0.31"

THREADED

GROOVE x GROOVE


GASKET SELECTION GUIDELede u�lizes the nest gasket materials available in our

products. Over the past 50 year great advanced have been made in synthe�c elastomer technologies, allowing us to offer a full range of synthe�c rubber gasket materials for a wide variety of piping applica�ons. Lede gaskets are engineered and designed to meet and exceed standards such as ASTM D2000, AWWA C606, NSF61 and IAPMO. Our own stringent internal laboratory tes�ng conrms this. Our con�nual research, development and tes�ng are designed to advance the elastomer eld and to develop new and be�er solu�ons for our ever changing industry.

Chemical resistance is primarily determined by the grade

Good for cold & hot water up to +230°F (+110°C). Also good for services for water with acid, water with chlorine, deionizzed water, seawater and waste water, dilute acids, oil-free air and many chemicals.Not recommended for petroleum oils, solvents and aroma�c hydrocarbons.

and or the compound of the gasket. The color coding iden�es the gasket grade and or compound. Always verify that the gasket selected is correct for the intended service.

Service temperature is controlled by factors including the gasket compound, uid medium (air, water, oils, etc.), and con�nuity (con�nuous or intermi�ent) of service. Under no circumstances should gaskets be exposed to temperatures ablow their individual ra�ngs. For addi�onal informa�on or specic applica�ons contact Lede for recommenda�ons.

Standard Gaskets

EPDM Green StripeE

Good for petroleum oils, mineral oils, vegetable oils, aroma�c hydrocarbons, many acids and water ≤ +150°F (+65°C).Nitrile Orange StripeT

Compound Grade Color Dode Recommended Services Maximum Temp. Range

-29°F (-34°C)to

+230°F (+110°C)

-20°F (-29°C)to

+180°F (+82°C)

Good for oily and greasy food products and processing, as well as pharmaceu�cal and cosme�cs manufacturing. Compounded from FAD approved ingrediients (CFR Title 21 Part 177.2600).

White Nitrile White GasketA-20°F (-7°C)

to+180°F (+82°C)

Good for dry, hot air without hydrocarbons and some high temperature chemical services. May also be used for re protec�on dry systems.

Silicone Red StripeL-29°F (-34°C)

to+350°F (+177°C)

Good for many oxidizing acids, petroleum oils, halogenated hydrocarbons, lubricants, hydraulic uids, organic liquids and air with hydrocarbons to +300°F (+149°C).

Fluoro-elastomer(Viton) Blue StripeO

-20°F (-7°C)to

+300°F (+149°C)

ANCHORING,�HANGING�AND�SUPPORTS�|�51

GASKET SELECTION GUIDE ARGCO utilizes the finest gasket materials available in our products. Over the past 50 year great advanced have been made in synthetic elastomer technologies, allowing us to offer a full range of synthetic rubber gasket materials for a wide variety of piping applications. Lede gaskets are engineered and designed to meet and exceed standards such as ASTM D2000, AWWA C606, NSF61 and IAPMO. Our own stringent internal laboratory testing confirms this. Our continual re-search, development and testing are designed to advance the elastomer field and to develop new and beer solutions for our ever changing industry.

GASKET SELECTION GUIDE FOR GROOVED

Chemical resistance is primarily determined by the gradeand or the compound of the gasket. The color coding identifies the gasket grade and or compound. Always verify that the gasket selected is correct for the intended service.Service temperature is controlled by factors including the gasket compound, fluid medium (air, water, oils, etc.), and continuity (continuous or intermittent) of service. Under no circumstances should gaskets be exposed to temperatures above or below their individual ratings. For additional informa-tion or specific applications contact ARGCO for recommenda-tions.


Lede couplings and mechanical tees are supplied complete with factory bolts and nuts. The bolt and nut torque is primarily a func�on of the bolt and nut size. The following table shows guidelines for nut and bolt torque and can be used when se�ng the torque on power drivers.

Do not exceed the design torque guidelines by more than 25%, as excessive torque could lead to joint failure. Always �ghten nuts evenly and equally by alterna�ng sides to prevent the gasket from being pinched and always check to make sure the coupling keys are fully engaged in the grooves.

The bolt pads on exible couplings have been designed to meet metal to metal when properly installed. Bolt pad gaps,

regardless of their size, are not acceptable on exible couplings. The listed values in the table 1 are guideline torque values listed by the coupling size. Please note these are only guidelines and that the actual torque value may be less than those listed to achieve a proper assembly. Actual torques for assembly of exible couplings are normally as li�le as 15-20 N-m (11-15 Lbs-�) for the bolt size of M10 (3/8’’) and 30-40 N-m (22 to 30 Lbs-�) for the M12 (1/2’’) bolt size. Do not a�empt to add further torque a�er the bolt pads make metal to metal contact.

If the bolt pads do not make full metal to metal contact, increase the torque to the listed guideline in table 1. Do not exceed the listed torque by more than 25%, as excessive torque could lead to joint failure. If bolt pad gaps s�ll exist a�er bolts and nuts have been �ghtened to the guideline torque, then this would indicate a problem in the assembly, pipe and or groove dimensions.

FLEXIBLE COUPLINGS

Table 1Flexible Coupling Torque Guidelines

Design Bolt Torques

Table 2Torque Guidelines for Angle-pad Rigid Couplings

The bolt pads on angle-pad rigid couplings and bu�-joint rigid couplings have been designed to meet metal to metal when properly installed. In assi�on as the bolts are �ghtened the bolt pads will slide against one another crea�ng a slight off-set. This offset should be equal on each side and is your visual indica�on that the coupling has been installed properly for a rigid connec�on. Bolt pad gaps, regardless of their size, are not acceptable on angle-pad coupling. The listed values in the table 2 are guideline torque values listed by the coupling size. Please note these are only guidelines and that the actual torque value may be less than those listed to achieve a proper assembly.

ANGLE-PAD RIGID COUPLINGS

BOLT TORQUES

BOLT TORQUES

5/16M83/8

M101/2

M125/8

M16

15 - 2011 - 1525 - 3018 - 2250 - 6837 - 50

80 - 12060 - 90

Bolt Sizein

N-mLbs -

3/4M207/8

M221

M24

1100 - 13574 - 100

170 - 275125 - 200275 - 400200 - 300

Bolt Sizein

N-mLbs -

1

1-1/4

1-1/2

2

2-1/2

3

4

5

6

8

10

12

14

16

18

20

22

24

Bolt Sizein

XGQT2N-m/Lbs-

60-7045-5060-7045-5060-7045-5060-7045-5060-7045-5060-7045-50

90-10065-75

90-10065-75

90-10065-75

200-230(JIS216 270-300)145-170(JIS216 200-220）

270-300200-220270-300200-220270-300200-220270-300200-220270-300200-220270-300200-220270-300200-220320-340235-250

------

60-7045-5060-7045-5060-7045-50

90-10065-75

90-10065-75

90-10065-75

200-230145-170200-230145-170270-300200-220270-300200-220270-300200-220

------------------------------------

1212N-m/Lbs-

1

1-1/4

1-1/2

2

2-1/2

3

4

5

6

8

10

12

Sizein

1512N-m/Lbs-

------

60-7045-5060-7045-5060-7045-50

90-10065-75

90-10065-75

90-10065-75

200-230145-170200-230145-170270-300200-220270-300200-220270-300200-220

60-7045-5060-7045-5060-7045-5060-7045-5060-7045-50

90-10065-75

90-10065-75

90-10065-75

200-230145-170200-230145-170

------------

60-7045-5060-7045-5060-7045-5060-7045-5060-7045-5060-7045-50

90-10065-75

90-10065-75

90-10065-75

200-230145-170270-300200-220270-300200-220

GKSN-m/Lbs-

XGQT4N-m/Lbs-

BOLT�TORQUES�|�61

ARGCO couplings and mechanical tees are supplied complete with factory bolts and nuts. The bolt and nut torque is pri-marily a function of the bolt and nut size. The following table shows guidelines for nut and bolt torque and can be used when setting the torque on power drivers

BOLT TORQUE FOR GROOVED

regardless of their size, are not acceptable on flexible cou-plings. The listed values in the table 1 are guideline torque values listed by the coupling size. Please note these are only guidelines and that the actual torque value may be less than those listed to achieve a proper assembly. Actual torques for assembly of flexible couplings are normally as lile as 15-20 N-m (11-15 Lbs-) for the bolt size of M10 (3/8’’) and 30-40 N-m (22 to 30 Lbs-) for the M12 (1/2’’) bolt size. Do not attempt to add further torque aer the bolt pads make metal to metal contact. If the bolt pads do not make full metal to metal contact, increase the torque to the listed guideline in table 1. Do not exceed the listed torque by more than 25%, as excessive torque could lead to joint failure. If bolt pad gaps sll exist after bolts and nuts have been tightened to the guideline torque, then this would indicate a problem in the assembly, pipe and or groove dimensions.

ANGLE PAD RIGID COUPLINGSThe bolt pads on angle-pad rigid couplings and butt-joint rigid couplings have been designed to meet metal to metal when properly installed. In addition as the bolts are tightened the bolt pads will slide against one another creating a slight offset. This offset should be equal on each side and is your visual indication that the coupling has been installed properly for a rigid connection. Bolt pad gaps, regardless of their size, are not acceptable on angle-pad coupling. The listed values in the table 2 are guideline torque values listed by the coupling size. Please note these are only guidelines and that the actual torque value may be less than those listed to achieve a proper assembly.






FLEXIBLE COUPLINGS


Design Bolt Torques




BOLT TORQUES

BOLT TORQUES

5/16M83/8

M101/2

M125/8

M16

15 - 2011 - 1525 - 3018 - 2250 - 6837 - 50

80 - 12060 - 90

Bolt Sizein

N-mLbs -

3/4M207/8

M221

M24

1100 - 13574 - 100

170 - 275125 - 200275 - 400200 - 300

Bolt Sizein

N-mLbs -

1

1-1/4

1-1/2

2

2-1/2

3

4

5

6

8

10

12

14

16

18

20

22

24

Bolt Sizein

XGQT2N-m/Lbs-

60-7045-5060-7045-5060-7045-5060-7045-5060-7045-5060-7045-50

90-10065-75

90-10065-75

90-10065-75

200-230(JIS216 270-300)145-170(JIS216 200-220）

270-300200-220270-300200-220270-300200-220270-300200-220270-300200-220270-300200-220270-300200-220320-340235-250

------

60-7045-5060-7045-5060-7045-50

90-10065-75

90-10065-75

90-10065-75

200-230145-170200-230145-170270-300200-220270-300200-220270-300200-220

------------------------------------

1212N-m/Lbs-

1

1-1/4

1-1/2

2

2-1/2

3

4

5

6

8

10

12

Sizein

1512N-m/Lbs-

------

60-7045-5060-7045-5060-7045-50

90-10065-75

90-10065-75

90-10065-75

200-230145-170200-230145-170270-300200-220270-300200-220270-300200-220

60-7045-5060-7045-5060-7045-5060-7045-5060-7045-50

90-10065-75

90-10065-75

90-10065-75

200-230145-170200-230145-170

------------

60-7045-5060-7045-5060-7045-5060-7045-5060-7045-5060-7045-50

90-10065-75

90-10065-75

90-10065-75

200-230145-170270-300200-220270-300200-220

GKSN-m/Lbs-

XGQT4N-m/Lbs-







FLEXIBLE COUPLINGS


Design Bolt Torques




BOLT TORQUES

BOLT TORQUES

5/16M83/8

M101/2

M125/8

M16

15 - 2011 - 1525 - 3018 - 2250 - 6837 - 50

80 - 12060 - 90

Bolt Sizein

N-mLbs -

3/4M207/8

M221

M24

1100 - 13574 - 100

170 - 275125 - 200275 - 400200 - 300

Bolt Sizein

N-mLbs -

1

1-1/4

1-1/2

2

2-1/2

3

4

5

6

8

10

12

14

16

18

20

22

24

Bolt Sizein

XGQT2N-m/Lbs-

60-7045-5060-7045-5060-7045-5060-7045-5060-7045-5060-7045-50

90-10065-75

90-10065-75

90-10065-75

200-230(JIS216 270-300)145-170(JIS216 200-220）

270-300200-220270-300200-220270-300200-220270-300200-220270-300200-220270-300200-220270-300200-220320-340235-250

------

60-7045-5060-7045-5060-7045-50

90-10065-75

90-10065-75

90-10065-75

200-230145-170200-230145-170270-300200-220270-300200-220270-300200-220

------------------------------------

1212N-m/Lbs-

1

1-1/4

1-1/2

2

2-1/2

3

4

5

6

8

10

12

Sizein

1512N-m/Lbs-

------

60-7045-5060-7045-5060-7045-50

90-10065-75

90-10065-75

90-10065-75

200-230145-170200-230145-170270-300200-220270-300200-220270-300200-220

60-7045-5060-7045-5060-7045-5060-7045-5060-7045-50

90-10065-75

90-10065-75

90-10065-75

200-230145-170200-230145-170

------------

60-7045-5060-7045-5060-7045-5060-7045-5060-7045-5060-7045-50

90-10065-75

90-10065-75

90-10065-75

200-230145-170270-300200-220270-300200-220

GKSN-m/Lbs-

XGQT4N-m/Lbs-


Do not exceed the design torque guidelines by more than 25%, as excessive torque could lead to joint failure. Always tighten nuts evenly and equally by alternating sides to prevent the gasket from being pinched and always check to make sure the coupling keys are fully engaged in the grooves.FLEXIBLE COUPLINGS The bolt pads on flexible couplings have been designed to meet metal to metal when properly installed. Bolt pad gaps


Pipe OD (Column 2): Maximum allowable tolerances from square cut ends is 0.03’’ for size up to 3 1/2’’; 0.045’’ for 4’’ thru 6’’; and 0.060’’ for size 8’’ and above.

Gasket Sealing Surface (Column 3): The gasket sealing surface shall be free from deep scores, marks, or ridges that could prevent a positive seal.

Groove Width (Column 4): Groove width is to be measured between vertical flanks of the groove side walls.

Groove Diameter (Column 5): The “C” diameters are average values. The groove must be of uniform depth around theentire pipe circumference.

Minimum Wall Thickness (Column 6): The “t” is the minimum allowable wall thickness that may be roll-grooved.

Groove Depth (Column 7): The “d” is for reference use only. The groove dimension shall be determined by the groove diameter “C”.

Flare Diameter (Column 8): The pipe end that may flare when the groove is rolled shall be within this limit when measured at the extreme end of the pipe.

ROLL GROOVE SPECIFICATIONS

Standard Roll Groove for ANSI B36.10 and Other IPS Pipe

July 2020 FIRE PROTECTION PIPING SOLUTIONS

ALLIED RUBBER &GASKET [email protected]

QUALITY SINCE 1981

ARGCO reserves the rights of final interpretation and modification of this catalog. All information is subject to change without notice.

GROOVEDPIPING SYSTEM

grooved quality since 1981 piping system · october 2019 fire protection piping solutions allied...

Documents