government of west bengal office of the ... conscious sedation kit 2 89 soldering blow torch 16 90...
TRANSCRIPT
1
GOVERNMENT OF WEST BENGAL
OFFICE OF THE PRINCIPAL DR. R. AHMED DENTAL COLLEGE & HOSPITAL
114, A. J. C. BOSE ROAD KOLKATA-700 014 Phone/Fax No- (033) 2265 5771
E mail: [email protected]
NOTICE INVITING E- TENDER FOR PURCHASE AND INSTALLATION OF DENTAL INSTRUMENTS BY THE PRINCIPAL, DR. R. AHMED DENTAL COLLEGE & HOSPITAL, KOLKATA- 700 014
(Through Pre-qualification) (Submission of Bid through NIC e- tender portal)
Memo No.:-DCH/5184 Dated-21.7.2016,Kolkata.
The Principal, Dr. R. Ahmed Dental College & Hospital having its office at 114, A. J. C. Bose Road Kolkata-700 014 is going for e-tender on behalf of the Health & Family Welfare Department, Government of West Bengal for obtaining the rate of Hospital Equipment/ Instruments as per annexed list from the bonafide manufacturer/authorized distributor. Necessary earnest money to be submitted for participation in the Tender through Demand Draft/Pay order is appended in the table below:
Name of the items Earnest money
As enlisted Rs 50,000/- per tenderer
List of instruments:
Sr. no Name of the Instrument Tentative Requirement
1. R. V. G. 16
2. Upright research Microscope with fluorescence, Dark field, Phase Contrast, Bright Field, Polarizing with Photographic Attachment.
1
3. OPMI PICO Surgical Microscope 2
4. Portable I.O.P.A X RAY & Phosphor Imaging System
2
5 Apex Locator3
rd Generation
17
6. Pulp Tester digital 20
7. Endomotor with torque control hand piece. 15
8. Injectable gutta percha obturation kit
5
9. EndoVac Irrigation System 2
10.
Endodontic microsurgical equipment:- Comprising of a. Ultrasonic scaler, b. Ultrasonic endodontic retro-surgical tips, c. Ultrasonic passive irrigation, d. Ultrasonic tip for inst retrieval and chasing calcified canal e. Ultrasonic tip for access cavity & floor refining
2
11. Endo activator 2
12. Ultrasonic cleaner 12
2
13. Magnification loupes 10
14. SAF endosystem 1
15. Intraoral camera 10
16. Implant surgical kit 2
17. Dental implants 100
18. Prosthetic component for dental implants 100
19. Sinus lifting instrument kit 1
20. Bone splitting kit 1
21. Implant motor with handpiece 2
22. 20:1 reduction gear contra angle handpiece 2
23. Piezo surgical kit 2
24. Bone grafting instruments 2
25. Implant Strengthening unit 2
26. Implant microsurveyor 2
27. Unit mount light cure unit 20
28. Steam cleaner 6
29. A) Softtissue laser(3 watts): 6
B) Softtissue laser(10 watts): 6
30. Hard tissue laser 1
31. Digital wax carver 4
32. Hanau wide view Arcon Articulator 12
33. Shade guide for all ceramic 3
34. Pneumatic crown remover 12
35. Manual crown remover 12
36. Wax heater 4
37. Plaster dispenser 22
38. Model trimmer with diamond disc 16
39. Model trimmer with double disc, 1pc diamond & 1 pc carborundum disc 12
40. Model trimmer with carborundum disc 12
41. Spot welder with soldering attachment 7
42. Lab micromotor 30
43. Dental lathe 5
44. Pressure moulding machine 8
45. Diamond disc 6
46. Hydro-solder 5
47. Vibrator 12
48. Acryliser 9
49. Pneumatic Deflasking unit 10
50. Hydraulic press 6
51. Manual press 6
52. Vacuum mixing machine 8
53. Heavy duty lathe with suction unit 12
54. Spindle grinder with vacuum suction 6
3
55. Front loading Autoclave 16
56. Dental surveyor 8
57. Clinical micromotor 24
58. Curing pressure pot 4
59. A.Laser guided pin drilling system (Pindex system) 4
B. Pins for use with Laser guided pin drilling system (Pindex
system) 1000 PC
60. Electro polisher 2
61. Preheating furnace 2
62. Waxburnout furnace 5
63. Hot air oven 12
64. Programmable porcelain furnace with vacuum pump 4
65. Casting machine motor cast with gas blow torch 4
66. Induction casting machine with vacuum pump 3
67. Milling machine 2
68. Dry model trimmer 8
69. Palatal trimmer 5
70. Ceramic instrument kit 4
71. Curing pressure pot 5
72. Deflasking unit 5
73. Sand blaster unit 6
74. Die cutting machine 4
75. Phantom head 70
76. Air motor handpiece 15
77. Microhead air rotor handpiece for pedodontics 12
78. Magnifying work lamp 15
79. Microvascular instrument kit 2
80. Vacuum investment unit 7
81. Light cure unit 30
82. Circular saw 4
83. Strycar saw 2
84. Oscillating saw 2
85. Colorado needle 6
86 Glass bead sterilizer 15
87 UV sterilizer 8
88 Conscious sedation kit 2
89 Soldering blow torch 16
90 Pikling kit 8
91 Amalgamator 11
92 Amalgam polishing kit 20
93 Automatic xray film developer 5
94 Rubber dam kit 20
95 Air polisher 6
4
96 Pneumatic chisel 2
97 Biopsy kit 5
98 Diagnodent 5
99 Dermatome 2
100 Pressurized local anaethesia 2
101. Composite curing unit system 2
102. Composite curing unit variable intensity 3
103. Composite finishing kit 12
104 Paeditric Extraction forcep kit 12
105. SS crown kit 12
106 Surgical elevators 40
107 Typhodont articulator with full teeth set 42
108 Electro surgery unit 2
109 Goldman fox probe 6
110. Marquis colour coded probe 4
111. Intraoral camera with fluroscent technology: 4
112 Paquette blade handle 10
113 Schluger bone file 4
114 Bone file 10
115 Kirkland’s knife 4
116 Buck’s knife 4
117 Orban knife 4
118 Micro scissor 10
119 Micro needle holder 10
120 Goldman fox scissor 4
121 Castrovejo scissor 14
122 Castrovejo needle holder 4
123 UNC-15 Peridontal probe 8
124 Naeber’s probe 8
125 Plastic UNC-15 probe 8
126 Periotest 2
127 Quetin furcation curette 12
128 Gracey’s curette 12
129 Plastic curette 6
130 After five mini five curettes 4
131 Universal- Columbia curette 4
132 Langer & mini Langer curette 4
133 Bone graft scooper 4
134 Bone condenser 4
135 Periotron 2
136 Perioscope 1
137 Corn plier 2
138 Centrifuge machine for PRF 4
5
139 Scwartz perioretriever 1
140 Periodontal bone chisel (Oschenbein) 2
141 Free plane articulator 100
142 Hinge articulator 30
143 Electronic anaesthesia 2
144 Orthodontic welding machine 4
1. General Instructions: In the event of e-filing, intending bidder may download the tender documents free of cost from the website : https://wbtenders.gov.in directly with the help of Digital Signature Certificate or from the Health & Family Welfare Department’s website www.wbhealth.gov.in& necessary earnest money may be remitted to the office of the Principal, Dr. R. Ahmed Dental College & Hospital through demand draft / pay order issued from any nationalized bank/scheduled bank in India payable at Kolkata drawn in favour of Principal, Dr. R. Ahmed Dental College & Hospital, Kolkata and also to be documented through e-filling.
2. Submission of bids :
Both Technical bid and Financial Bid are to be submitted concurrently duly digitally signed by the authorized signatories in the websitehttps://wbtenders.gov.in. All papers must be submitted in English language.
3. Time Schedules for the e-tender : THE TIME SCHEDULE FOR OBTAINING THE BID DOCUMENTS, PRE BID MEETINGS, REGISTRATION WITH THE TENDERING AUTHORITIES, THE SUBMISSION OF BIDS AND OTHER DOCUMENTS ETC. WILL BE AS PER THE LIST PROVIDED IN CLAUSE NO 21 AS GIVEN BELOW.
4. ELIGIBILITY FOR QUOTING : Only Manufacturers OR authorized distributors are only eligible for quoting having an Annual Turnover of Rs 3 (Three) Crore for last 3(three) years i.e for the year 2012-13, 2013-14 & 2014-15 totalling 9(nine) crores for three years.
5. SUBMISSION OF THE TENDERS : The tender is to be submitted in a two Bid System. [A] Technical Bid:
(a). Statutory Cover Containing the following documents: 1. COVER “A”:
“BID A”: PART I One folder for earnest money deposit with copy of the Demand draft/Pay order should be uploaded. Local SSI(s) should upload certificate of registration/EM II for claiming EMD exemption. (SINGLEFILEMULTIPLEPAGESCANNED) Essential Requirements of the Tendering Firm for participation” shall contain all papers related to the essential requirements of the Tenderer for participation in the tender viz.
A Copy of Demand Draft/Pay order of Rs 50,000/-(Rs fifty thousand only) in favour of Principal, Dr. R. Ahmed Dental College & Hospital’, Kolkata submitted as Earnest Money for the whole tender.
B CHECK LIST in the prescribed format
C Application in the prescribed format given in Annexure I
E Authorization letter of signatory from Company in Annexure II
F Authorization letter of Distributor from Company in Annexure III
6
“BID A”: PART II TECHNICAL SPECIFICATIONS OF THE ITEMS IN THE GIVEN FORMAT IN PDF. NON-STATUTORY/ MY DOCUMENTS Containing the following documents:
Sn Category Sub Category Sub Category Description
A. Certificates A1. Certificates PAN Card of the authorized signatory
Professional Tax Registration certificate
VAT/ CST Registration certificate
B. COMPANY DETAILS
B1. COMPANY DETAILS
Trade License
Registration with Registrar of Companies
C. CREDENTIAL C1: Credential 1 Affidavit for No conviction
Certificate of country of origin relating to the Equipment/Instrument
C2 : Credential 2 Manufacturing License
Manufacturer’s Guarantee
Test Report from the leading Test House
Quality Assurance certificate of the Equipment/Instrument.
LIST OF PURCHASERS
Credential certificate from Purchasers
Manfacturer’s authorization for distributor
D.
FINANCIAL INFO
PAYMENT CERTIFICATE 1
Income Tax Returns submitted for the year 2012-13
Income Tax Returns submitted for the year 2013-14
Income Tax Returns submitted for the year 2014-15
VAT/CST Returns (of the last quarter) for the year 2012-13
VAT/CST Returns (of the last quarter) for the year 2013-14
VAT/CST Returns (of the last quarter) for the year 2014-15
D1. P/L & BALANCE SHEET
1. P/L & Balance sheet 2012-13
2. P/L & Balance sheet 2013-14
3. P/L & Balance sheet 2014-15
2. COVER “B” : [B] FINANCIAL BID “B” : (i) BOQ for INR (in excel sheet)
The folder as “Financial Bid” shall contain base price of the equipment/Instrument with 3(three) years on-site comprehensive Warranty in Indian currency including cost of insurance, packing, freight charges, delivery charges, testing charges, incidental charges, if any and cost of the installation of the Instrument but excluding of VAT/CST, Entry tax, Cess and other Govt taxes(if any) to be shown separately in the Bill of Quantities.
7
The cost of CAMC for next 5(five) years are to be quoted separately in the BOQ. The L1 will be determined only on Base rate with 3(three) years comprehensive on-site warranty including cost of insurance, packing, freight charges, delivery charges, testing charges and incidentals, if any. The appropriate % of VAT/CST, Entry tax, Cess or other taxes as claimed by the bidder would be applicable as per prevailing Govt order. The cost of CAMC for next five years is to be quoted separately in the BOQ. The tenderers are required to submit the hard copies of Bid A alongwith the Brochure of the Equipment/instrument as per schedule more clearly described in the time line vide clause 21 along with Earnest Money Deposit (EMD) in separate packets. Submission of hard copy of Bid A to the office of the Principal, Dr. R. Ahmed Dental College & Hospital(RADCH) is for reference only while examining the technical bid on line and will not be treated as substitute for on line submission. However, Brochure/testimonials of the equipment are to be enclosed separately with the hard copy of Bid A for examination. Submission of hard copy of Bid B is totally prohibited and only be submitted through on line through NIC portal.
6. Evaluation of the tenders
During the tender evaluation process on line, the “Bid A” will be opened first. The Tenderer who have qualified the essential & other requirements will be identified and only their “Bid B” i.e. Financial bid will be opened. The “Bid B” of those Tenderer failing to meet the technical & other requirements of participating in the tender will not be opened and be rejected. The Tenderer offering the item found suitable and as being as per the tender specifications will only be selected. The Tenderer who have been so identified to have been technically suitable in the context of above will be deemed to have passed the test of essential and other requirement of the quoted item or items. Physical verification of samples(optional) may be undertaken to adjudge the suitability and applicability of the functional requirement of the Instrument/machine/items The “Bid B” (Financial Bids) of only these tenderers passing the essential and other requirement test will be opened then subject to verification of hard copies of the audited balance sheet and Profit & Loss Accounts of the tenderer for the last three years i.e for the year 2012-13, 2013-14 & 2014-15. If found suitable in the context of above pre qualification etc, the Tenderer quoting the lowest rate in the base price with 3(three) years comprehensive on-site warranty will be considered as successful.
7. Cost of Earnest Money : Each tender has to be submit, unless exempted under the existing orders of the West Bengal Govt. must deposit Earnest Money in the form of Demand Draft/Pay order from any Nationalized Bank/scheduled bank in India for Rs. 50,000 (Rs Fifty Thousand) only for the whole tender. The earnest money is to be deposited in the prescribed time before opening of Bid A. The onus of proving that a Tenderer is exempted from Earnest Money will lie on the Tenderer and must be proved by submission of valid documents. The earnest money of the Tenderer will liable to be forfeited if the Tenderer withdraws his tender as a whole or for any particular item or items at any stage after the opening of the tender, or fails / refuses to enter into written agreement for any of all of the items of his accepted tender within the time specified when requested to do so/fails to furnish Performance Bank Guarantee within the stipulated time. The Earnest Money will be refunded after finalization of the tender or within 3 (three) months from the date of opening of tender, whichever is later against the specific prayer of Tenderer.
8. RATE:
The price is to be quoted in Indian Rupees with cost of 3(three) years on-site comprehensive warranty including cost of insurance, packing, forwarding, freight charges, delivery charges, testing charges, incidental charges, if any and installation of the instrument. The instrument is to be transported in such packaging so that there is no damage to the primary packaging during the transportation process. VAT/CST, Excise Duty, Entry Tax & Cess etc. which shall be quoted separately in the template for Bill of Quantities (BOQ).
8
Percentage of Excise Duty, CESS etc, Percentage of VAT to be mentioned in the appropriate Column of the template for Bill of Quantities.
9. ORDER & SUPPLY: Orders for the supply of the approved products will be placed with the successful tenderers after the execution of the agreements. The successful tenderer will have to supply within the specified time schedule that had been assured at the time of selection as supplier.
10. WITHDRAWAL /CANCELLATION & PURCHASE POLICY OF TENDERING AUTHORITY: a. The tendering authority reserves the right to withdraw any item from the tender at any
stage. The selection of such item, if already made in favour of any Tenderer, shall be treated as cancelled.
b. The tendering authority reserves the right to reject or accept any tender or part thereof at any stage or to split any tender without assigning any reason. Withdrawal of tender or any revision after submission of tender by the Tenderer will not be allowed.
c. The tendering authority reserves the right to accept or reject any tender, in part or in full, without assigning any reason.
d. Purchase will, however be made following the existing purchase policy of the Govt of West Bengal and its amendment(s) made from time to time. The purchase policy of the State Government as provided in the West Bengal Financial Rules, the policy of price preference in particular incorporated under Notification No. 10500-F dated 19.11.04 should be observed in considering the tenders.
11. Spare Parts On being selected, the L1Bidder will undertake that supplies of necessary maintenance equipment and spare parts will be made available for all items/equipments and the complete system for at least five years on a continuing basis. However, this does not relieve the supplier of any warranty obligations under the contract.
12. GUARANTEE / WARRANTY PERIOD: THE TENDERERS MUST QUOTE BASIC RATE ALONGWITH 3 YEAR COMPREHENSIVE ON SITE WARRANTY OF ENTIRE SYSTEM (INCLUDING ALL SPARES & LABOUR) FROM THE DATE OF COMPLETION OF THE SATISFACTORY INSTALLATION. For Extended warranty of 5 years rate should be quoted separately.
13. Delivery, Installation and Commissioning : a. Delivery of the goods at the purchaser's premises shall be completed by the Supplier in
accordance with the terms specified by the purchaser. The installation, testing and commissioning of the proposed system shall be completed in accordance with the order.
b. In case of distributor, the firm should be direct distributor from the principal's. The sub-distributor or authority by distributor will not be accepted at all.
14. SPECIAL TERMS AND CONDITIONS FOR TENDER SUBMISSION Quality assurance certification like ISO 9000 series or higher should be attached wherever applicable.
15. PENALTY CLAUSES- PENALTY FOR FORMATION OF CARTEL OR FURNISHING OF FRADULENT/ MISLEADING DOCUMENTS:
i. If during the tender process or at any state during the validity of the tender period, it is found that a Tenderer(s) has formed a cartel in what so ever form or name to fix up the rates or suppliers to the detriment of the fairness of the tender process, penal measures shall be initiated by debarring him from joining in the tender and his earnest money will be forfeited straightaway and the firm will be blacklisted for a period of 3(three) years.
ii. Similar penal measures shall also be initiated against those tenderers who have submitted false/ misleading/ fraudulent documents or made incorrect declarations. The penal measure will also include Forfeiture of Performance Bank Guarantee if enlisted as a supplier.
9
16. APPEAL: Appeal against the decision of the Principal, Dr. R. Ahmed Dental College & Hospital, West Bengal and the to impose such a penalty will lie with the H&FW Dept. The Special Secretary/Secretary/Principal Secretary will be the appellate authority within the Department of Health & Family Welfare, Government of West Bengal. Before imposing any penalty as per clauses 15 the concerned supplier may appeal to the authority citing the proper reasons for non- imposing the penalty as stated.
17. AGREEMENT: On a tender being accepted, intimation of acceptance will be forwarded to the Tenderer by Principal, Dr. R. Ahmed Dental College & Hospital. After communication of the same, the Tenderer will have to execute agreement in the prescribed form with the Principal, Dr. R. Ahmed Dental College & Hospital.
18. VALIDITY PERIOD OF AGREEMENT: The contract period will be for a period 1(one) year from the date of finalization of tender.
19. PERFORMANCE BANK GUARANTEE’ The performance bank guarantee will be mandatory for all suppliers and will not be waived in any case. The successful tenderers shall be required to furnish the ‘Performance Bank Guarantee’@ 10% of L1 rate per item for which the Tenderer has been selected as supplier.
20. PAYMENT TERMS: Payment will be made through e payment system through ECS/RECS/RTGS after execution of due supply as ordered subject to: a. Submission of Performance Bank Guarantee in terms of Clause 19 and subject to
penalty clause in terms of Clauses 15. b. Supply of the materials as per specification as provided in the tender documents. c. Supply of the materials within the supplied period as specified in the work orders. d. On being selected, the successful vendors will have to submit one application to the
RADCH stating the name of the payee/ recipient, Bank account no with MICR code, IFSC of the payee/recipient for making e payment.
e. No manual payment is allowed to be made as far as practicable.
21. Dates & Information :
Sn Items Publishing date(s)
1. Date of uploading of N.I.T. Documents (online) from this end. 05.08.2016
2. Documents download/sell start date (Online) 05.08.2016
3. Date of Pre Bid Meeting with the intending bidders at the office chamber of the Principal, Dr. R. Ahmed Dental College & Hospital, 114,A.J.C Bose Road, Kolkata – 700 014
19.08.2016 at 12.00 Noon
4. Date of hoisting of documents at Departmental Website (www.wbhealth.gov.in)
05.08.2016
5. Bid Submission starting (On line) 20.08.2016 at 05.00 pm
6. Bid Submission closing (On line) 12.09.2016 at 05.00 pm
7. Last Date of submission of original copies along with Earnest Money Deposit (Hard Copy)
12.09.2016 by 5.00 pm
8. Bid opening (Bid A ) 13.09.2016 12.00 NOON
9. Date of uploading list for Technically Qualified Bidder (online) (Bid A) 20.09.2016 onwards
10. Date & Place for opening of Financial Proposal (Bid B) (Online) 20.09.2016 onwards
11. Date of uploading of list of bidders along with the approved rate 20.09.2016 onwards
10
PRINCIPAL, DR. R. AHMED DENTAL COLLEGE & HOSPITALRESERVES THE RIGHT TO CHANGE THE ABOVE SCHEDULE IN CASE OF ANY EXIGENCIES AFTER PUTTING UP A NOTICE IN THE DEPARTMENTAL WEBSITE AND RADCH NOTICE BOARD. No objections in this respect will be entertained raised by any Bidder who will present during opening of bid, or from any Bidder who will absent at the time of opening of Financial Bid. No informal tenderer will be entertained in the Bid further. During the scrutiny, if it come to the notice to tender inviting authority that the credential or any other paper found incorrect/ manufactured/ fabricated, that bidder would not allowed to participate in the tender and that application will be out rightly rejected without any prejudice AND PENAL PROVISION AS LAID DOWN ABOVE WILL BE IMPOSED AGAINST HIM. A HELP DESK is set up in the office of .Principal, Dr. R. Ahmed Dental College & Hospital, 114A.J.C. BoseRoad, Kolkata – 700 014 for technical guidance & Dy. Director of Health services ( E&S), Central Medical Stores,141,A.J.C. Bose Rd, Kolkata -700014 to help and guide the prospective bidders about their registration, holding of Digital Signature Card and allied matter. Prospective bidders may contact personally or over phone vide phone no (033)2212 3695/97 or mail their queries in the following e mail addresses: a. [email protected] b. [email protected] Prospective bidders must take training from authorised agencies stationed in the Central Medical Stores, 141, A J C Bose Road, Kolkata – 700 014 before submission of their bids. The Tender Selection Committee/Purchase committee reserves the right to accept, reject any item or items and cancel the N.I.T. due to unavoidable circumstances and no claim in this respect will be entertained.
Principal Dr. R. Ahmed Dental College & Hospital
11
FORMAT FOR CHECK LIST
Sn Items Pl mark Page no
1 Application submitted in Annexure I Yes No
2. Annexure II (Authorization letter of signatory from the Company) Yes No
3. Annexure III (Copy of authorization of the distributor from the Company.
Yes No
4. Copy of PAN Card of the authorised signatory Yes No
5. Copy of Demand Draft/Pay order of Rs 50000/- in favour of Principal,
Dr. R. Ahmed Dental College & Hospital’ payable at Kolkata as Earnest Money
Yes No
6. Last 3 financial years’ returns of Income Tax i.e. for 2012-13, 2013-14 & 2014-15
Yes No
7. Last quarters of last 3 financial years’ returns of VAT for 2012-13, 2013-14 & 2014-15
Yes No
8. Last quarters of last 3 financial years’ returns of CST for 2012-13, 2013-14 & 2014-15
Yes No
9. Affidavit of non conviction affirmed before a Notary public/ First Class Judicial Magistrate/Executive Magistrate (affidavit sworn after 01.06.2015)
Yes No
10. Manufacturer’s guarantee Yes No
11. Test report from leading test house Yes No
12 Manufacturer’s authorization to distributor Yes No
13. Certificate about quality assurance Yes No
12
Annexure I
APPLICATION FORMAT ( To be furnished in the Company’s official letter pad with full address and contact no etc)
To
The Principal Dr. R. Ahmed Dental College & Hospital 114, A.J.C. Bose Road, KOLKATA-700 014
Sub : NIT for Hospital Equipment/ Instruments for Dr. R. Ahmed Dental College & Hospital, Kolkata (RADCH)
Ref : RADCH Memo No …………………………………….. dated …………………… Sir, Having examined the pre-qualification & other documents published in the N.I.T, I /we hereby submit all the necessary information and relevant documents for evaluation : 1. That the application is made by me / us on behalf of ………………………………………
In the capacity of……………………………………………..…duly authorized to submit the offer. The authorization letter from the Company is attached in Annexure II.
2. We accept the terms and conditions as laid down in the NIT mentioned above and declare that we
shall abide by it for throughout the tender period. 3. We are offering rate for the following item /items and assured supply to the Dr. R. Ahmed Dental
College & Hospital under Health & Family Welfare Department, Government of West Bengal as per Table-1 (Instruments Specification)
4. The copy of the authorization letter from the manufacturer is attached in annexure III 5. In the event of being selected, supply will be made within the stipulated period excepting the
condition which is beyond our control. 6. We understand that :
(a) Tender Selection Committee/ Purchase committee of the RADCH/ H&FW Dept can amend the scope & value of the contract bid under this project. (b) Tender Selection Committee/ Purchase committee of the RADCH/H&FW Dept reserves the right to reject any application without assigning any reason ;
Date :-
Signature of applicant including title and capacity in which application is made.
Contact no : Tele : Mobile :
E Mail address :
13
Annexure II Authorization letter from Company for authorized signatory who will upload the bid on behalf of the Company
15
TABLE I LIST OF EQUIPMENT / INSTRUMENTS :
(SPECIFICATIONS)
LIST OF DENTAL INSTRUMENTS WITH SPECIFICATION
1) R. V. G imaging system:
a) X ray unit(fixed type)
Sl No.
Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation
if any
1 DC xray with timer and wall mounted scissor arm stand
2 60-70 kvp,4-8 Ma
3 total wt 25 Kg
4 Radiation- --minimum exposure time 0.02 sec upto 3.2 sec,leakage radiation less than 0.25mgy/hour maximum at a distance of 1 mt from focal point.
5 AERB approved.
b) Digital Intra Oral Sensor:
Sl No.
Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation
if any
1 ACE technology
2 Gadox scintilltor with white sided strips for better positioning in mouth.
3 Auto ready sensor
4 Virtual implant library in software.
2) Upright research Microscope with fluorescence, Dark field, Phase Contrast, Bright Field,
Polarizing with Photographic Attachment.
Sl
No
Technical Specifications as follows or better Technical
Specification
quoted by
bidder
Bidders deviation if any
1 ICOS system with upto 2000 X Magnification.
2 Trinocular Head I.P adjustment 53mm to 75mm graduated inclined at 30°. Photo and Video attachment with Sliding 80/20 beam splitter for attaching Video/ Digital Camera.
3 Standard Universal Eye piece and objectives with Quintuple Nosepiece.
16
4 Universal Semi-Apo Plan objectives with high light UV transmission. 4X,10X,20X,40X,100X(OIL) optional 2.5x, 50x(oil)
5 Ceramic coated flat top low position drop down right hand drive ergonomic X-Y Coaxial controls. 191mm x 128mm. stage should be with hard coat and rugged enough to provide smooth usage without any abrasion and ware and tare.
6 Universal Condenser suitable for bright field, dark field, Phase contract, Polarizing and florescence observation.
7 True Koehler 30W Illumination with automatic voltage sensing power supply
8 Modular fix position Fluorescence illuminator for egfp, s65 T, PI and RFP filter cubes. 100W HG HBO Lamp (2200L)
9 Microphotography attachment with Image documentation system. 3mp or better color cooled ccd with image analysis system. Individual calibration for all magnification are required in all linear measurement and annotation. Camera should have the capability to capture the fluorescence images simultaneously upto 5 filters with image merging capability.
Standard Accessories:
a. 30W spare 1 no.
b. 100W HG HBO 1 no.
c. Standard European power cord 2 no.
d. Spare fuse 3amp.
e. Polyvinyl dust cover.
f. Immersion oil.
The above microscope should be upgradable in future with motorized focus and noise piece.
10 Branded computer with HDMI LED MONITOR (24”).
3) OPMI PICO Surgical Microscope:
Sl No Technical Specifications as follows or better Technical
Specification
quoted by bidder
Bidders deviation if any
1. OPMI pico microscope body without magnification changer
2. Magnification changer for OPMI pico
3 Dust cover for OPMI,blue
4 6 pack asepsis caps 12 mm
5 Tiltable binocular tube f=170mm,180 degrees
6 sleeve for tubes with screw thread(Qty-2)
17
7. Widefield push in eyepiece 12.5x(Qty-2)
8. Objective lens f=250mm with focusing mechanism(screw thread of lens
48mm)
9 Handgrip(back) for OPMI pico
10 120 degree coupling for S 100 and OPMI pico
11. S 100 Floor stand
12. Halogen illumination for S 100 suspension systems
13. Blind cover plate
14. Pack of 6 asepsis caps 22 mm
15. Pack of 6 asepsis caps 12 mm
16. Pair of sterilisable handgrip covers(2x)
17. Pack of 2 asepsis caps 49mm(Qty-2)
Accessories for OPMI Pico:(DESIRABLE) Stereo co observation,complete with straight binocular tube and 12.5x eyepieces
4. PORTABLE I.O.P.A X RAY & IMAGING SYSTEM:
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
15. Stereo co-observation tube with two joints.
16. Widefield push-in eyepiece 12.5x(Qty 2)
17. Sleeve for tubes with screw thread
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
FOR PORTABLE I.O.P.A X RAY
18
5.:Apex Locator
A. Apex Locator3rd
Generation
B. Apex Locator 6th Generation
6. Pulp Tester digital:
1. Cordless,
2. battery operated,
3. >300 exposure with one time charging.
FOR IMAGING SYSTEM-- Phosphor imaging plate & laser scanner
1. Phosphor imaging plate sizes (0,1,2,3)
2. laser scanner technology for digital intra oral
imaging.
3. Scanner with preview screen & ultra violet cleaning
system.
4. Front loading of imaging plate for scanning & wake
up sensor in the scanner.
5. Networking capable upto 8 computers.
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
1. 3rd
Generation- Apex Locator with lip clip,
display module, file clip & associated chord
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
1. 6TH
Generation- Adaptive Apex Locator with
lip clip, display module, file clip & associated
chord
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
1. Preset speed mode,
2. Battery-9V
19
7. Endomotor with torque control hand piece:
8. Injectable gutta percha obturation kit:
9.EndoVac Irrigation System:
3. Auto-off after 3 min
4. autoclavable tips,
5. one touch operation, with digital read out
display
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
1. Continuous & reciprocating
motions for root canal shaping
2. Hand piece with integrated
on- off switch,auto reverse
mode
3. Speed 250-1200 rpm.
4. Torque range 0.6-4 Ncm
5. Multiple adjustable programs.
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
1. Dual Kit-Pluggers-variable sizes.
2. Flexible extra long heat conductible silver alloy
cannula
3. 1 cartridge capable of filling more than 3 root
canals
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
1. Multiple Port adapters
2. Hand Piece set
3. Extra Evacuation System,cannulas,delivery tips &
syringes.
20
10.Endodontic microsurgical equipment:
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
a.Ultrasonic scaler
1. Ultrasonic piezoelectric scaler with inbuit irrigation
& led HD pe deiven through Newtron technology.
2. Colour coding power control system.
3 Tank-300 ml
4 Wt-2120gm
b.Ultrasonic endodontic retro-surgical tips
1 Ultrasonic piezoelectric tip for endo retro cavity preparation.
c.Ultrasonic passive irrigation
1. Ultrasonic piezoelectric tip for passive irrigation.
d.Ultrasonic tip for instrument retrieval and chasing calcified canal
1. Endo success retreatment kit
e.Ultrasonic tip for access cavity & floor refining
1. Diamond coated assorted tip set of 5
11. Endo Activator:
12. Ultrasonic cleaner:
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
1. Safe & vigorous energetizing intracanal irrigant
2. Capable of debridling & disinfecting Root canal
system
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
1. Ultrasonic cleaner 220V, 120 watt & above,
21
13. Magnification loups:
14.SAF Endosystem:
15. Intraoral camera:
16.Implant surgical kit:
17.Dental implants:
2. 5 liter capacity, with stainless steel cover
Sl No Technical Specifications as follows or
better
Technical Specification
quoted by bidder
Bidders deviation if any
1. Ergonomically designed STAC binocular
loupe2.5X and 4.5X
Sl No Technical Specifications as follows or
better
Technical Specification
quoted by bidder
Bidders deviation if any
1. Rotary mode Reciprocating mode SAF
mode Irrigation system set of SAF files.
Sl No Technical Specifications as follows or
better
Technical Specification
quoted by bidder
Bidders deviation if any
1. Intra oral camera with caries detection
and periogingival inflammation
detection facility based on flurescent
technology
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
1. Implant surgical kit comprising of
Surgical armamentarium comprises of: point drill,
pilot surgical drill, tap drill,drill extension, counter
sink, stopper, connectors, parallel pin,depth
gauge, torque rachet, fixture direction pin, fixture
driver, hex driver & other related items
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
1. Dental implants
Single stage and two stage dental implants with
cover screw, impression analog,cover screw &
other attachments
22
18. Prosthetic components for implants:
19.Sinus lifting instrument kit:
20.Bone splitting kit:
21.Implant motor with handpiece:
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
1. Prosthetic components for implants
Straight abutment, Angled abutments of various
angulations, Ball abutment & socket with silicon &
plastic ring, UCLA abutment, Healing abutment,
Impression post, Impression post, Gingiva former,
Laboratory analog, Castable waxing sleeve and screw
& other attachments
Components for implant supported overdentures- ball
attachments,stud attachments, milled bar, microstud
attachments.
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
1. Sinus lifting instrument kit
For Lateral & crestal approach s-reamer, initial drill,bone inserter,bone spreader, bone carrier, bone condenser,depth gauge, chisels, sinus curette, bone rongeur forceps, mallet & other instruments
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
1. Bone splitting kit
Spreaders, burs surgical, saw disc, thumb driver, rachet
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
Implant motor with handpiece
Control unit with display panel, powerful motor with integrated thread cutting function, provided with tool control for handsfree operation. Handpiece- autoclavable, upto 80Ncm torque, speed
controllable between 200-4000min-1,brushless
micromotor, upto 8 programmable memory, hands free
operation via foot control for speed/coolant solution
23
22. 20:1 reduction gear contra angle handpiece
23.Piezo surgical kit
24.Bone grafting instruments:
25.ImplantStrengthening unit:
flow volume/forward reverse/program. Optical
Handpiece calibration system,light power over
30000LUX,cooling attachment system . pump output
70ml/minute,
size 265x210x100mm
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
20:1 reduction gear contra angle handpiecehaving r.p.m minimum 10
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
Piezo surgical kit: device with intermittent operation,
60 sec on then 30 sec off with irrigation, & 30 sec on-
120 sec off without irrigation, power supply
240V,50/60 Hz, maximum power absorbed 120VA.
Surgical tip capable of modulating from 10, 30 & 60
cycles/s (Hz) to 29kHz. Power adjustable from 2.8 to
16W. Tip vibration in range of 60-200µm.Motor with
tips & other accessories
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
Bone grafting instruments comprising of-Bone block clamps,
membrane tacks, center point trephine kit, Osseo tip bone
grafter, bone saws, bone cylinder grafting kit, bone mills, bone
morseliser, osseous trap, graft mixing dishes, ramus retractors,
graft packers, osteotomes, bone spreaders, sinus window bone
tampers, rongeurs, bone curettes, bone chisels( 4mm, 6mm,
8mm, 10mm)
Sl No Technical Specifications as follows or
better
Technical Specification
quoted by bidder
Bidders deviation if any
1. Unit comprising of probe attached with display meter via chord, works on principle of universal ISQ scale, a testpeg attached to implant is tested for mobility.
24
26.Implant microsurveyor:
27.Unit mount light cure:
28.steam cleaner:
29.(A) Softtissue laser(3 watts):
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
1. Wt not less than 365 gm.
Suitable guideline for ensuring the
placement of denture. Capable of observing
difficult to see locations.
Sl No Technical Specifications as follows or
better
Technical Specification
quoted by bidder
Bidders deviation if any
1. 5 W LED light or more
Light power intensity > 1200 MW/cm2
Wavelength of 470 nm Electrically operated.
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
1. Dental Steam cleaner: power 1500W or more, 220V,
frequency 50/60hz. Working Pressure: 4-5 bar. Capacity
10Litre or more. with thermostat controller. Device
with both steam gun & button/lever controlled
steaming attachment. Stainless steel non rusting inner
tank body.
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
1. Diode Soft tissue laser(3 watts),Features: 21 preset
programs,4 customised programs,4 hrs battery
backup,large LCD screen, cordless foot control,buit in
help tutorials and other specialized features with 3 yrs
warranty.
Laser unit 3 watt(1 no), laser goggle(3 no), eye
protector(1 no), multi tip permanent fibre in spool
form (1 no), user manuals(1 no),set up DVD(1 no),
carrying case(1 no).
25
29.(B)Soft tissue laser(10watts):
30.Hard tissue laser
31.Digital wax curver
32.Hanau wide view articulator
33.Shade guide
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
2. Diode Soft tissue laser(10 watts) Features: 21 preset
programs,4 customised programs,4 hrs battery backup,large
LCD screen,cordless foot control,built in help tutorials and other
specialized features with 3 yrs warranty.
Laser unit 10 watt(1 no), laser goggle(3 no), eye protector(1 no),
multi tip permanent fibre in spool form (1 no),
,Bleaching hand piece(1 no),user manuals(1 no),set up DVD(1
no), carrying case(1 no).
Sl No Technical Specifications as follows or better Technical Specifica-
tion quoted by
bidder
Bidders deviation if any
1. Hard tissue laser-Er,Cr: YSGG laser,0.1-9.0W(450
mJ)10-50 Hz,laser classification 4,voltage 100- 230 Vac
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
1. Digital wax carver
Digitally operated electrical wax carver with
two detachable carving tools
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
1. Hanau wide view Arcon Articulator With
spring bow, earpiece, face bow, orbital
indicator, bite fork & other accessories
Sl No Technical Specifications as follows or
better
Technical Specification
quoted by bidder
Bidders deviation if any
1. SHADE GUIDE FOR ALLCERAMIC Vita 3D
master and Vitapan
26
34. Pneumatic crown remover
35. Manual crown remover
36.Wax heater
37.Plaster dispenser
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
1. Pneumatic crown remover Pneumatic,
autoclavable tips, Basic Kit Includes Easy
Pneumatic Crown and Bridge Remover II Bridge
remover tip 1 Single crown remover tip 2 Single
crown remover contrangled tip 3 Openend
adjustment wrench Rubber gasket Flexiwire set
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
1. Manual crown remover Single crown remover tip 2
Single crown remover contrangled tip 3 Openend
adjustment wrench
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
1. Wax heater pot with temperature regulator
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
1. plaster dispenser
Body made of stainless 304 grade dull finish fitted with
digital electronic timer, capacity 10 kg.
Unident Dental Plaster Dispenseroutside body made of
mild sheet with stoving paint & inside stainless steel
304 grade operate with press on switch, capacity 10 kg.
27
38.Model trimmer with diamond disc
39.Model trimmer with double disc, one diamond & one carborundum disc :
40. Model trimmer with carborundum disc
41.spot welder with soldering attachment
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
1. Model trimmer with diamond disc HP-1 RPM-
2800, Heavy Duty Equipped with Two Ball Bearings,
Single speed, Rating continuous with buffer and
one 12" Diamond Disc Rough or fine without
suction.
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
1. Model trimmer with double disc, one diamond & one
carborundum disc RPM 2800 Double Motors HP-1
each, Heavy duty, Equipped with Two Ball Bearings
each motor, Single speed, Rating continuous with
fixed one10" diamond disc fine, one carborundum
coarse cutting wheel, base inlet, outflow water
system.
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
1. Model trimmer with carborundum disc RPM 2800
Heavy duty, Equipped with two Ball Bearing Single
speed, Rating continuous with Buffer and 10"
Diamond Disc rough or Fine heavy base, inlet, out flow
water system.
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
1. Spot welder with soldering attachment Type Ortho
Electrically operated
Voltage110 volts
220 volts
Applications / IndicationElectrosoldering
Wire Annealer
Power SettingsUp To 200 Amperes
Heat Settings3
Electrode / Tip TypeCopper
Carbon
28
42. Laboratory micromotor
43.Dental lathe
44.Pressure moulding machine
Welding Positions12
Included ComponentsBrass Posts
Footswitch
7 Copper Welding Tips
2 Remote Electrode Cords
Insulating Material
Flux
Carbon Points
Sample Of Solder
8 ounces Of Safety Solvent Cleaner
8 ounces Of HotStop
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
1. Laboratory micromotor Compact and portable size
Continous variable speed control, R.P.M.
On/Off foot switch
One- touch change of the driving direction for
efficient operation Possible to attach a Contra Angle
or straight handpiece
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
1. Dental lathe motor Ac, HP-1, Universal, RPM-2800,
Equipped with Double B.B, Single speed, Rating continuous
with 3 chucks (Buffer, Stone & Bur Chuck), Three Imported
B.B. flexible metal cable arm and its attachment.
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
1. Pressure moulding machine with Scan technology and
increased working pressure of 6 bar.
29
45.Diamond disc
46. Hydro solder
47. Vibrator
The unique thermally controlled infrared heater reaches
working temperature in one second. All important data
are printed on each single sheet and are read by the
scanner and shown on the large display.
Power: 230 V,
Working pressure: 0,5 – 6,0 bar
Measurements (W x H x L): 450 x 230 x 260 mm
Sl No Technical Specifications as follows or
better
Technical Specification
quoted by bidder
Bidders deviation if any
1. Diamond disc for model trimmer
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
1. Mains voltage: 1 x 230 V Mains frequency: 50 x 60 Hz Mains fuse: 1 x 10. A Max.gas production: 6 liter Max. Nozzle size: 0.07mm Dimensions W x H x D x (mm): 330 x 230 x 310 mm Weight: 22 Kg Capacity: 110lt, with accessories
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
1. Electrically operated - Size114.3 x 203.2 x 165.1 mm
(4.5 x 8 x 6.5 inches) or more
TypeHeavy Duty
ConstructionEnamel body
Speed3-Speed
Table / Platform Size Table / Platform
Shaperectangular
30
48. Acrylizer
49.PneumaticDeflasking unit
Sl No Technical Specifications as follows or
better
Technical Specification
quoted by bidder
Bidders deviation if any
Pneumatic deflasking unit with handheld chisel- provided with detachable tips , provided with variable powercontrol with air inlet and tubing length not less than 1.5 meter. Working pressure 1-6 bar
50. Hydraulic press
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
The closed circuit hydraulic press (press i) should work with a pressure up to 7000 Kg of thrust. It can contain up to three flasks at a time. The structural elements in chromium plated steel. Provided with dial.
51. Manual press
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
1.
Stainless steel body.Temperature is controlled by
thermostat from 5°C above ambient to 100°C with a
sensitivity of +-5’C. with timer can be set 1/2 Hour to 2
Hours.drain valve is provided for dewaxing. To work on
220/230 volts Ac. The gap between the walls is filled with
glass wool to minimize loss of temperature.
Double walled, Outside & inside body made of Stainless
steel 304 Grade. Inner Size 300 x 250 x 350 mm. or more
31
This equipment with base and cross bar in cast iron and the structural elements in chromium plated steel. High resistance model. Ideal equipment for 1 to 3 flasks. The base has 4 holes for attachment to the bench
52. Vacuum mixing machine
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
Electrically operated motor 150 watts or more
compact
automatic regulation of the vacuum
the mixing motor remains clean and is easily serviced due to a supporting filter and a fine filter in conjunction with the maintenance-free vacuum pump
direct connection between mixing bowl and vacuum pump – no disturbing exterior hose
mechanical coupling tolock the mixing bowl in position
a choice of 3 mixing bowls (900 g, 500 g and 120 g)
53. Heavy duty lathe with suction
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
Electrically operatedHeavy duty motor unit having power not less than – 0.5hp High speed 3000 rpm Arrangement to attach Bur holding chuck – M. S. Electroplated or spindle for buffing wheel on one. On the other arm is a Grinding Wheel. Built in High Power dust suction behind chuck for clean, unpolluted, dust free work environment. Dust collection bag – easily removable and emptied Tray for debris collection. Table mountable Heavy Base Plate for vibration free operation Built – in lighting for high visibility
32
54. Spindle grinder with vacuum suction
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
Foot control and high intensity illumination.
Safety glass for glare elimination and visual
protection.
Provision for connection dust collector suction.
Operating voltage 230VAC +/- 10% 50Hz.
Motor rotation at 24000rpm or more
55. Front Loading Autoclave
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
B-Type front loading fully automatic autoclave
with vacuum & dry cycle
22 ltr capacity and micro processor controlled
Wrapped/unwrapped, porous, solid
instrument including cotton swabs can be
sterilized
Bow and Dick test qualified
Digital display of pressure and temperature
Double safety lock on the door
Silicon Gasket prevents any leakage of air
Diagnostic automatic alarm for any
malfunctioning
Can be used at 121 degree C/134 degree C
during sterilization.
2 Storage tanks for fresh and used water.
Chamber Size 250mm*450mm
Net weight 55Kg
No. of Tray 3 No. Front Loading micro Bacteria control with 3 loading tray, dry cycle, in built water chamber , digital display, capacity 22 liters
56. Dental surveyor
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
33
Dental surveyor Ney’s type Horizontal Platform • Adjustable spindle for the vertical indicator • Survey table that can be locked at any angle With tools- analyzing rod, undercut gauges, carbon marker sheath, wax trimmer etc Provision for holding handpiece
57. Clinical micromotor
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
Electrically operated,autoclavable upto 135 degree celcius,handpiecespeed 1000-
40000rpm,speedmaximum output power 1.2W,3.4-
3.5 Ncm torque,with option of clockwise &
anticlockwise rotation.Control box and foot control mechanism.
58.Curing pressure pot
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
5 liter or more capacity pressure potTemperature is preset to approximately 120ºF and manually adjusts to a maximum 160ºF. Solid clad bottom provides even heat distribution. Includes an easy-to-read, built-in pressure gauge and quick-release air valve. The pot has a safety device to prevent overheating, and a secure double-locking lid. Easy-to-clean stainless steel interior. Rubber feet keep pot firmly in place. Lid Gasket
59.
A. Laser guided pin drilling system (Pindex system)
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
Electrically operated 220V, Laser guided
Pinsetter, pin drilling for easy die pin
attachment. laser light technology with
carbide bur drill with high speed motor. To
Accurately Drill Parallel Holes Into The
34
Underside Of The Model
B. Pins for use with Laser guided pin drilling system (Pindex system)
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
Die pins made with non corrosive alloys for
use with pindex system of die pins.
60. Electro polisher
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
Automatic digital electro polisher, Auto/Manual
Modes, With timers, Electrolyte flow regulation
38 mm disc for PSA paper & cloths
Supply 230 V. AC
Current – 2.5 Amp., Voltage – 80V, Supply – 230
V.A.C.Polishing probes – Unique Pen Type system
with Recirculation of electrolyte, pump 25 watts
reservoir (0.5 Ltr)
61.Preheating furnace
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
Maximum temperature range:
950 degree celcius, working temperature 900 degree celcius, with ER & digital display with suitable insulation arrangements with ceramic fabric wool.the outer caging of double wall thick, muffle furnace with microprocessor based programmable controller two indicators light & safety fuse. Arrangement of viewing sample without opening the door. Size 175x175x225mm. 3.0 k.w. capacity
62. Wax burnout furnace
35
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
Maximum temp 1200C working temp 1150C with Digital Display cum temperature controller with safety alarm size : 175x175x225mm 4.0k.w
63. Hot air oven
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
to work on 220/230 volts a.c., Doublewalled, Operating temperature thermostatically controlled from 50ºc to 250ºc with a sensitivity of +/- 1ºc, with three trays. Ventilation will be on top of the oven. Motorised air circulation will be provided for uniformity of the heater, Timer setter.
64. Programmable porcelain furnace with vacuum pump
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
Power connection 110-120 V50-60Hz 200-240 V 50-60Hz Acceptable voltage fluctuations ±10% Max. power consumption 12 A at 110-120 V 8.5 Aat 200-240V Data for the vacuum pump Max. power consumption: 2.1 A Final vacuum: < 50 mbar Use only tested pumps Display Graphic LCD Display with background lighting Dimensions of electrical fuses 110-120 V: diameter 6.3 x 32 mm 200-240 V: diameter 5 x 20 mm Dimensions of the closed furnace Depth: 430 mm Width: 305 mm/410 mm (with cooling tray) Height: 565 mm Usable size of the firing chamber Diameter: 80 mm Height: 48 mm Max. firing temperature 1200 °C/2192 °F Weight Furnace base: 12.0 kg Furnace head: 7.0 kg Safety notes The furnace was built in accordance with the following standards: IEC 1010-1/EN 61010 UL and cUL standards Radio prot
65. Casting machine motor cast with gas blow torch
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
36
motor driven table top casting machine equipped with centrifugal arm.
Gas blow torch based melting technique
Ceramic melting crucibles
Casting of all dental alloy (except titanium)
size : 700D x 550W x 450H approximately.
Power rating : 3000 Watts
66. Induction casting machine with vacuum pump
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
Power:AC220V 50Hz-60Hz 2000Watt or more Centrifugal mount:620 r/min, melting type: induction, casting sequence 3-5 minutes ,maximum Melting temperature 1700 ˚C, maximum weight of alloy to be melted 60gms, Built in vacuum pump with vacuum adjustment by digital software, vacuum level 0.7 Bar or lesser, maximum pressure 3.5 Bar attachment for argon gas supply. Casting ring dimensions minimum 50 x 55mm & maximum 100 x 70mm Motor power:350W or more
67. Milling machine
Sl No Technical Specifications as follows or
better
Technical Specification
quoted by bidder
Bidders deviation if any
Capable of unattended 5-axis milling
with simple one-button operation
Precision milling of wax, zirconia, nano composites and PMMA
Integrated air flow system keeps work area clean
Diagnostic notification system alerts user of machine status
CAM software
Material sizes supported disc, pin & ingot
68.Dry model trimmer
37
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
High speed dry trimmer with dust suction unit.
Burr :Tungsten Carbide.
Supply:230 Volts Single Phase, 50 C/S, A/C
69. Palatal trimmer
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
Dental Palatal Trimmer, RPM-2800 high torque 304 grade S.S. Dull Finish work surface, Dust collection with adapter hose, provided with1 fast cutting trimmer
70. Ceramic instrument kit
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Ceramic carving kit comprising of high quality sable hair/ synthetic filament brush size one zero, two zero and four zero and other sizes, ceramic curver, mosquito forcep, tweezer, ceramic pallete for mixing ceramic powder and other associated carving & finishing instruments.
71. Curing pressure pot
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Curing pressure pot, size 5 liter or more,internal temperature gauge, temperature controller, air lock and safety valve, compressed air inlet.
38
72. Deflasking unit
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
Dimensions WXHXD 380x540x450mm,lamp source, blasting chamber volume 23ltr.with 2m cable&deflasking chisels of 6 types-flat,channeled,pointed,rivet,blank, suction unit and foot control. Working pressure 1-6 bar, air consumption 200ltr/minute,voltage 230v, 5oHz,
73. Sand blaster unit
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
Dual sand blaster is used for coarse & fine sand blasting in the same cabinet with foot control and also provided with fixed type & pencil type nozzles. Pressure control : By regulator
Pressure Gauge : Provided for both functions
Blasting process : By foot control
Sand used : Aluminium oxide
74. Die cutting machine
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Electrically operated with diamond disc. With adjustable model holder self illuminated
39
75. Phantom head
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Dental phantom head unit: manikin head with mounted upper & lower jaw containing screw mounted ivory teeth having 90˚ swiveling function of head unit, provided with control box for micromotor, foot control & micromotor handpiece, should have mounted light unit with illumination power not less than 7000 LUX.
76. Air motor handpiece
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Straight Handpiece Contra Angle Handpiece
easy to connect with all handpieces and contra-angles
(NSK, KaVo®, Sirona®, W&H®,
Bien-Air®)
Midwest 4 holes and Borden
2/3 holes compatible
Optic and non-optic
Internal or external water spray
Autoclavable up to135° Adjustable speed control
Forward and reverse direction control
Speed limitationVariable speed in either forward or reverse
1:1 Direct Drive
Non-Retraction Valve
Quick Handpiece Attachment
Max speed 22000 min-1
Capability to attach to ALL brands of ISO E-type handpieces
All Autoclavable
40
components
77. Microhead air rotor hand piece for pedodontic use
Sl No
Technical Specifications as follows or better Technical Specification quoted by
bidder
Bidders deviation if any
Rotation 300,000~450,000 min-1
Mini Head Size Ø8.5x H19.4 mm
Water Spray Single Spray
Body Material Stainless steel/alloy
Autoclavable.
78.Magnifying work lamp
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Handheld magnifier
Magnification: 10X
Lens diameter: 50 mm
79.Microvascular instrument kit
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Micro scissors
Micro needle holder
Jwellers forceps
Vessel dilators
Liga clips(no.100.no.200)
Ligaclip applicators
Vessel clamp (2A,2V,3A,3V)
41
Vessel clamp applicator
Hand held colour Doppler unit
Pneumatic tourniquet
Specification to be quoted by the Bidder / Manufacturer
80. Vacuum investment unit
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Voltage 85-245V 50/60 Hz Mixing Speed 100-500 RPM Premix, 100-400 RPM Vacuum 27.5 in Hg (930 mbar )User Programs 25 Mixing Time1-255 Seconds (4.25 Minutes )
81. Light cure unit
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
5 W LED light or more
Light power intensity >
1200 MW/cm2
Wavelength of 470 nm Electrically operated
82. Circular shaw
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Thin and fast slitting of model.
Accurate slitting.
Compact unit.
Supply:230 Volts Single Phase, 50 C/S,
42
A/C
Uses circular saw.
Motorised model slitting unit
83. Strykar saw
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Specification to be quoted by the Bidder / Manufacturer
84. Oscillating saw
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
With saw-blade
One drive speed for all 3 saw types
high-grade stainless steel
For sagittal, oscillating or reciprocal movement
Range of saw blades for all surgical applications
Low vibration
Dismantlable for thorough cleaning. Separate hanpieces for sagittal motion, with oscillating motion, cutting direction 90° to the axis, with reciprocating motion, forward / reverse cutting direction
85. Colorado needle:
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
43
Colorado needle ultra-sharp tungsten tip allows the surgeon to use very low wattages, resulting in dramatically reduced bleeding with minimal tissue damage
86. Glass bead sterilizer
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Size 60x60x100mm or more 230 volt, 50hz Preset Temp. Range 425-475 degree farenheit. 15 to 20 minutes to reach operating temperature of approximately 240 C to 270 C. Unit can be left in the “ON” position all day and is safe for use in laminar flow cabinets. unit overheat and trip safety switch
87. UV Sterilizer
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
With front door, cabinet form with ss multiple trays, Door switch interlock prevents emission of UV light as soon the chamber is opened to avoid any harmful effect on operator. Electronic circuits for instant start without flickering of tube Rated Power of UV tube: 15W Rated Voltage: 220V Rated Frequency: 50Hz Capacity: 20Liter or more Disinfection Temperature: 35℃ Disinfection Time: 15minPacking Dimension(mm): 300*180*480
88. Conscious sedation kit
44
Sl No Technical Specifications as follows or better Technical Specification
quoted by bidder
Bidders deviation if any
Included in Kit:
(1) 10.4" Multi-Parameter Patient Monitor: This Multi-parameter monitor provides essential measurement parameters such as SpO2, NIBP, ECG, Temp & HR and offer high cost-performance ratio to give care teams throughout the hospital more of the information they need right at the patient’s side, such as ambulance, doctors’ office, out-patient department, and post-operative. ** End Tidal CO2 is an available upgrade. Printer and Roll Stand Included. (1) Clear Plastic gel Electrodes, 50/bg.
Oxygen Delivery System: (1) Cylinder Holder “Wheeled” (1) Nasal Cannulas 50/cs (1) Click Style Oxygen Regulator (1) Bag Valve Mask (5) O2 Adapter/Christmas Trees (5) Full Face Masks
Airway Equipment: (1) Color Coded Oral Airway Kits Sz 60mm-110mm. (1) Surgilube- 3gm foil Packets 144/bx (1) Adjustable Nasal Airway 28Fr (1) LMA ( Each Sz 3,4 & 5) (1) King Airway (Each Sz 3,4 & 5) (1) Cricothyrotomy Kit Adult (1) CPR Board (10) 60ml Syringe only
Blood Pressure Cuff & Stethoscope: (1) Dual Head Stethoscope (1) Omron Blood Pressure Kit: Professional stethoscope attached to cuff. Includes vinyl carrying case, illustrated instructions, and blood pressure chart. For adults. (1) Precordial Stethoscope Kit: 4 Piece wenger Chest pieces
Back up Lighting:
45
(1) Head Lamp Ancillary Equipment: (1) IV Administration Set 15 dp/ml, 50/bx (1 of each) Syringe w/ Needle 100/bx Sz 3ml, 5ml, 10ml. (1 of each ) IV Catheters 20G & 22G, 50/bx (1) 8 Qt Sharps Box (1) 2.37 x2.75" Tegaderm IV Transparent Dressing 100/bx (1) Transpore surgical Tape 12/bx (1) Drive Medical 4 Hook IV Pole (1) Alcohol Pads, 200/bx (1) LF Tourniquets, 100/bx
Suction Equipment: (5) Yankauer W/ tubing (1) Ambu Rescue Pump Hand Held (Back up)
89.Soldering blow torch
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Dental Melting Torch for Chrome cobalt and Nickle chrome alloys used with LPG and Oxygen with air flow regulator, two separate inlet line
90.Pikling kit
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Electrically heated and thermostatically controlled pickling unit for Neacid pickling agent with low power consumption for pickling of precious metals. Swivel sieve and housing made of shock-proof and acid-resistant polypropylene
91. Amalgamator
46
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Input voltage 230V
Touch pad selector
Pre-programmed time setting
Quiet, high-speed mix capsules
Built-in automatic timer
Accepts all capsules
Customized trituration times
92. Amalgam polishing kit
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
kits are designed for polishing and superpolishing amalgam and precious alloys.
93.Automatic x-ray film developer
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Processes all films from 2 x 3 , 3 x 4, 15 x 30 up to 24 x 30 cms Dry to dry in 5 minutes, all auto processing Auto temperature control and auto film transport
94. Rubberdam kit
47
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Rubber Dam Clamp Forceps (RDF)
Rubber Dam Punch (RDP)
Rubber Dam Frame - Adult (RDAF6)
Universal Rubber Dam Template (RDTUNIV)
FDI Rubber Dam Provided with different clamp designs
95. Air polisher
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
ergonomic handle; a lighter plastic reservoir and a new improved design. MULTIflex connection, sterilizable up to 275°F (135°C), 44 psi. Water 7.2-10 psi.
96.Pneumatic chisel
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Pneumatic handpiece,provision for 3 interchangble chisel with connection pipe.
97.Biopsy kit
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
The instruments - Small and short scalpel blades (no. 15, 11, 12 or even 5) - Mosquito forceps - Allis tweezers - 2/0 to 5/0 non-traumatic suture material 3 - Gauze - Container with fixing solution, alley,s tissue forcep, punch biopsy , Chalazion clamp, macintosh
48
dissecting scissor
98. Diagnodent
Sl No
Technical Specifications as follows or better Technical
Specifica-
tion
quoted by
bidder
Bidders deviation if any
cordless, Wavelength of 655 nm
Size: 17.5 cm x 10.5 cm x 8.5 cm
Weight: net 375 g
Voltage: 6V (4 alkaline mignon cells LR6 (AA))
Technical Data Length Approx. 220 mm Diameter Approx. 32 mm Weight 110 g Voltage 1 good quality Alkaline LR6 battery 1.5 V Intensity < 1 mW Wavelength 655 nm Protection category covered IPX0 Calibration temperature +22°C ±2° C relative humidity 30% RH to 75% RH
99. Dermatome
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Electricaliy operated dermatome designed to harvest large, uniform-thickness skin grafts using electric power. These dermatomes are typically handheld instruments that include an electric powered rapidly oscillating cutting blade that is manually advanced over the skin.
dermatome kits include:
Handpiece
Handpiece Cable
Power Supply
Wall Cord
Width Clips
Guard Plate
Dermatome
49
Screwdriver
Pin Position Guide
Carrying Case Dermatome power Supply 110-230 Volts Unique depth regulation system * Guard always parallel with blade edge. * Free access in restricted areas. * Practically maintenance-free and can be sterilized by all current means (steam autoclaving, Ethylene Oxide etc.)
100. Pressurized local anaesthesia
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Needle free anaesthethetic injectable system with needle handpiece, digital control unit.
101. Composite curing unit system:
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Light SourceHalogen
ConstructionErgonomically
Designed Pistol Grip
Autoclavable Fiber Optic Probe
360° Rotation
Thermal Switch
Wall Mounted or Free
Standing
Automatic Timer with Audible
Tone
Other AccessoriesEye
Protection Shield
Chamber DimensionsHxWxL
80mm x 160mm x 125mm (3.1
50
inches x 6.3 inches x 4.9 inches)
Internal Fan IncludedYes
102. Composite light curing unit with variable intensity
Sl No
Technical Specifications as follows or better Technical
Specifica-
tion
quoted by
bidder
Bidders deviation if any
Tip (# of sizes) 3 (3mm, 9mm, 13mm)
Power (mW/cm2) 2700 (± 10%, center 4mm beam)
Cure All Materials Yes(with purchase of optional violet light module)
Battery Smart Li-Ion rechargeable with built-in charging/protection electronics. 1-year warranty with typical service life of 5 years. User replaceable.
Run Time (minutes)
40 (high plasma-like power); 90 (Standard LED power)
Recharge Time (hrs) 1.5
Weight 3.9oz/110g
Timer options Constant 5, 10 (HiPower), 5, 10, 20, 60 (PulsePower)
Curing Time 5 seconds (A3 or lighter shades)
Standard Warranty 2 years (battery 1 year)
103 Composite finishing kit
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Specification to be quoted by the Bidder / Manufacturer
51
104. Pediatric extraction forcep kit
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Set contains:
English pattern Forceps for Children Upper Incisors No. 37
English pattern Forceps for Children Upper Molars No. 39
English pattern Forceps for Children Upper Molars Right No. 39R
English pattern Forceps for Children Upper Molars Left No. 39L
English pattern Forceps for Children Upper Roots No. 51S
English pattern Forceps for Children Lower Premolars No. 13S
English pattern Forceps for Children Upper Roots No. 30S
English pattern Forceps for Children Lower Roots No. 33S
English pattern Forceps for Children Lower Molars No. 22S
English pattern Forceps for Children Lower Incisors and Canines No. 38
Technical Specifications Material: Stainless Steel Rusting Prevention Procedure:Passivated Ultrasonic Cleaned: Yes Lubricate: Yes Polished: Yes Dull-Polished: No (but possible) Usage: Left Hand or Right Hand Tests Performed: Boil Test, Performance Test, Shape Test Packing: Individually Packed Set contains:
English pattern Forceps for Children Upper Incisors
52
No. 37
English pattern Forceps for Children Upper Molars No. 39
English pattern Forceps for Children Upper Molars Right No. 39R
English pattern Forceps for Children Upper Molars Left No. 39L
English pattern Forceps for Children Upper Roots No. 51S
English pattern Forceps for Children Lower Premolars No. 13S
English pattern Forceps for Children Upper Roots No. 30S
English pattern Forceps for Children Lower Roots No. 33S
English pattern Forceps for Children Lower Molars No. 22S
English pattern Forceps for Children Lower Incisors and Canines No. 38
Technical Specifications Material: Stainless Steel Rusting Prevention Procedure:Passivated Ultrasonic Cleaned: Yes Lubricate: Yes Polished: Yes Dull-Polished: No (but possible) Usage: Left Hand or Right Hand Tests Performed: Boil Test, Performance Test, Shape Test Packing: Individually Packed
105.SS Crown kit
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Assorted primary Molar Sainless Steel crown forms,complete kit,set of 96 crowns.these prefabricated stainless steel crowns are manufactured with life like height,contour and occlusal
53
surface.they are pre crimped at the cerviucal margin.
106. Surgical elevators
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
a Cryers elevator
b Apexo elevator
c Warwick james elevator(straight,curved)
d Coupland elevator
e Flor elevator
f Bien elevator
107. Typhodont articulator with full teeth set
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Model with Soft Pink (Not Transparent) acrylic or plastic Gingivae Material. Included:28 anatomically shaped screwable typodont teeth
108. Electro- Surgery unit
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
a Monopolar unit, Electrosurgery unit 110V, 220V with handpiece unit having Operating modes for cutting, Coagulating & other uses 8 or morePower level settings Specifications: Maximum power output: 45W (@ 400 ohm load) Power supply: 110V± 5% ~50/60Hz 92VA or 220V± 5% ~50/60Hz 92VA Work frequency: 1.5~1.7MHz±
54
5% Dimension (cm): 23(L) X 22.5(W) X 8.5(H) Hand piece cable length: 180cm Indifference plate cable length: 180 cm Hand piece Indifference plate Electrode tip Foot switch AC Adapter Optional Accessories: Bipolar converter: ISO and CE Certifiedspecification to be provided by bidder
b Bipolar Electrosurgery unit having Operating modes for cutting, Coagulating & other uses 8 or morePower level settings Specifications: Electrode tip Foot switch AC Adapter other specification to be provided by bidder
109.Goldman fox probe
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
1-2-3-5-7-8-9-10 Flat probe with missing marks at 4 & 6 mm Flat shank
110. Marquis color coded probe
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
3-6-9-12 markings, colour coding 3 to 6 & 9 to 12 Thin shank
55
111. Intraoral camera with fluroscent technology:
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Intra oral camera with caries detection and periogingival inflammation detection facility based on flurescent technology
112. Paquette blade handle
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
For palatal surgery and other bowed blade techniques. Improved blade-holding mechanism for use with bowed blade - See more at: http://dentalmart.in/scalpels/676-kpq-paquette-blade-handle.
113. Schluger bone file
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Straight or curved bone files for smoothening periodontal bone. Used interproximally. File surfaces on both sides allow for push or pull application.
114. Bone file
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Howard bone file. Used for smoothening of bone during surgical procedures.
56
115. Kirkland’s knife
Sl No
Technical Specifications as follows or better Technical Specification quoted by
bidder
Bidders deviation if any
a surgical knife with a heart-shaped blade that is sharp on all edges. It is used for a primary gingivectomy incision (external beveled incision).
116. Buck’s knife
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Stainless steel autoclavable IS7833 (1975)
117. Orban knife
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
for incisions that remove or recontour soft tissue. Also useful to excise interproximal tissue. IS7833 (1975)
118. Micro scissors
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Small scissor used for cutting small tissue. The blade is curved with tip very small.
119. Micro needle holder
57
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Needle holder for holding needle during giving sutures.
120. Goldman fox scissors
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Goldman-Fox standard scissors with 1 serrated blade used for trimming tissue. Stainless steel or other alloy, autoclavable.
121. Castrovejo Scissors
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Castroviejo scissor has curved
blades.
Ultra-sharp blades
microscopic serrations provide
a smooth cut.
Spring-loaded knurled handles
provide the control you need
to make perfectly smooth cuts
in delicate materials.
stainless steel, autoclavable
122. Castrovejo needle holder
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Castroviejo Microsurgical Needle Holder is a double spring instrument used for holding small, delicate needles in various microsurgical procedures. It also features a locking mechanism.
58
123.UNC -15 Periodontal probe
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Markings at 1-2-3-4-5-6-7-8-9-10-11-12-13-14-15 Colour coded at 5,10 & 15mm, thin shanked probe
124. Naeber’s probe
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Used for measuring furcations in multi-rooted teeth. Curved for easy access to furcation area.
125. Plastic UNC-15 probe
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
flexibile and a rounded tip provide greater patient comfort and acceptability. The probe tips are safe for use with implants and feature a twist-on design for easy replacement of worn tips.
126. Periotest
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Teeth and implant mobility measuring device. Guidelines are available with the manufacturer
59
127. Quetin furcation curette
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Stainless steel autoclavable, with shallow half moon shaped curette blade, shank shlightly curved, sizes: BL1,MD1, BL2 &MD2 ISO 13397-2-2005 ANSI/ADA Standard No- 113 (2008)
128. Gracey curette
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Gracey curette set of nine hand instruments. Each having blade edge at 70 degree offset. Autoclavable and made of stainless steel. ISO 13397-2-2005 ANSI/ADA Standard No- 113 (2008)
129. Plastic curette
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Used for subgingival curettage around dental implants in peri-implantitis, where conventional metal curettes cannot be used because of chances of contamination of Ti surfaces.
130. After 5 curettes
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Hand instrument with longer terminal shank, instrument number ½,3/4,5/6,7/8,11/12,13/14,15/16. Stainless steel autoclavable ISO 13397-2-2005 ANSI/ADA Standard No- 113
60
(2008)
131. Universal columbia curette
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Columbia Curette blade designed with two cutting edges and a rounded toe for use on all surfaces ISO 13397-2-2005 ANSI/ADA Standard No- 113 (2008)
132. Langer and mini langer curette
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Combination of Gracey shank bend with universal curette bend 4 designs are available- SL-1/2, 3/4, 5/6, 17/18 ISO 13397-2-2005 ANSI/ADA Standard No- 113 (2008)
133. Bone graft scooper
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Bone graft scoop is used for transferring graft materials during gtrafting
134. Bone condenser
61
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
4 mm Bone grafting plugger used during grafting procedures with 8-11-13-15-18 mm markings.
135. Periotron
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Differences in calibration
fluid composition (e.g.
protein content) are
reflected in the Periotron
scores
Positioning of filter paper
strip between the jaws of
the Periotron should be
standardised,
Calibration of the
Periotron 8000 seems to
be consistent over a 1-wk
interval.
Periotron Model 8000 is
a micro-moisture meter
electronic instrument
that has been designed
to measure gingival
crevicular fluid,
periodontal pocket fluid,
salivary flow and saliva
thickness. Includes
#700100.
PerioCol Paper Strips For
collecting larger volumes
(0 - 2.0 μl) of GCF fluid.
Package contains 10
sterilized strips.
Periotron Professional
3.0 A software program
that performs rapid
conversion of Periotron
Scores to volume (μl) and
Sialo Scores to saliva film
thickness (μm)
measurements on tooth
or oral mucosa surfaces.
62
Also includes patient
tracking with charting.
For Windows 98, Me,
2000 and XP
SialoPaper Strips For
minor salivary gland
collection and oral
mucosal wetness
measurements. Each
strip collects 0 - 3.0 μl.
Package contains 10
sterilized strips.
PerioPaper Strips Special
paper strips that absorb
or carry 0 - 1.2 μl of fluid.
Used with all Periotron
models. Box contains 20
sterilized packets. Each
packet contains 16 test
strips.
136. Perioscope
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
1-mm diameter fiberoptic ENDOSCOPE camera attached toPerioscopy Explorer images displayed on a chairside monitor magnification20-40 times, disposable sterile sheath as accessories over camera
137 Corn plier
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Suturing Forcep With "Pass Through" Hole At Tip
#2 Octagonal Handle
63
138. Centrifugal machine for PRF
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Centrifugal machine, PRF box, tubes, instrument kit Specification to be quoted by the Bidder / Manufacturer
139. Scwartz perioretriever
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
set ol two double-ended, magnetized instruments Specification to be quoted by the Bidder / Manufacturer
140. Periodontal bone chisel (Oschebein pattern)
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
1/2 Buser Modified and others Periodontal Chisel 3mm/5mm Specification to be quoted by the Bidder / Manufacturer
141. Free plane articulator
Sl No Technical Specifications as
follows or better
Technical Specification
quoted by bidder
Bidders deviation if any
Specification to be quoted by the Bidder / Manufacturer