golden grow® aeroponic combo system manual
TRANSCRIPT
8/12/2019 Golden Grow® Aeroponic Combo System Manual
http://slidepdf.com/reader/full/golden-grow-aeroponic-combo-system-manual 1/12
!"#$%& !(")!
www.goldengrow.com
Instructions
Golden Grow ® Aeroponic Cloning System
grow
for the
GOLD
8/12/2019 Golden Grow® Aeroponic Combo System Manual
http://slidepdf.com/reader/full/golden-grow-aeroponic-combo-system-manual 2/12
2
Thank you, and Congratulations!
Thank you for purchasing a Golden Grow ® Cloning System! We are
very excited to bring you a new way to get the most out of your
growing experience. With the Golden Grow ® Cloning System, you’llbe able to create up to 48 clones of your favorite plants more
quickly with flawless results.
Come visit us at
www.goldengrow.com
for more cloning tips, information, parts, and accessories. See
included pump manual(s) for additional safety and use instructions.
Table of Contents
3 What’s In The Box?
4 Things to Check Before Initial Use
5 Using the System to Create Clones
7 Using the System for Vegetative Growth
9 Pro Tips
10 Troubleshooting and Support
11 Warranty Information
© 2013-2014 by Golden Grow, Inc. All rights reserved
8/12/2019 Golden Grow® Aeroponic Combo System Manual
http://slidepdf.com/reader/full/golden-grow-aeroponic-combo-system-manual 3/12
3
What’s in the Box?
1 10-Gallon Reservoir
2 Submersible Pump
3 Sprinkler Manifold with Sprinkler Heads
4 48-Site Cloning Lid
5 1” Neoprene Inserts (60)
6 Green Grommets for the Cloning Lid (48 installed, 2 spare)
7 Large Green Closed Grommet
8 Small Green Open Grommets (2)
9 Small Green Closed Grommets (2 installed)
12-Site Vegetation Lid (Combo Kit Only)3.75 in. Net Pots (Combo Kit Only)
Air Pump (Combo Kit Only)
Air Stones (2) with Vinyl Tubing (Combo Kit Only)
1
2
3
4
5
6 7
8,9
8/12/2019 Golden Grow® Aeroponic Combo System Manual
http://slidepdf.com/reader/full/golden-grow-aeroponic-combo-system-manual 4/12
4
Things to Check Before Initial Use
The green grommets installed in the 48-
site cloning lid can get jostled out of
place during the shipping process.
Check to ensure all the grommets are
firmly seated into the lid and form a good
seal.
Check to make sure the pump cord and
the grommet form a good seal with each
other and the reservoir. Check to make
sure the cord is not pulling on the
grommet at a tight angle, which may
cause the grommet to deform and water
to leak from the container during
operation.
The green handles on the container are
made in such a way that they will pop
out of place at the joint if too much direct
pressure is put on them. This prevents thehandles from breaking. If a handle has
slipped out of place during shipping,
simply reseat the handle into the notches
in the reservoir base.
Occasionally, the pump and manifold
may become unseated during theshipping process. Simply secure the
pump to its base and place it in the
center of the reservoir.
8/12/2019 Golden Grow® Aeroponic Combo System Manual
http://slidepdf.com/reader/full/golden-grow-aeroponic-combo-system-manual 5/12
5
Using the System to Create Clones
1. Always start with clean equipment and clean hands. All of the
Golden Grow ® System parts can be cleaned by hand with
simple soap and warm water. Lids, grommets, and reservoirscan be placed into a dishwasher. Cleaning should be done
before every use to reduce the chances of accidentally
growing molds or fungi with your new clones.
2. Ensure that the pump and manifold are seated firmly in the
center of the reservoir with the long edge of manifold parallel to
the long edge of the reservoir.
3. Fill your reservoir with 12L (approx. 3 gal.) of clean water,preferably without chlorine or chloramine (a good filtered water
will do). If you use RO or distilled water, be sure to add the
appropriate calcium and magnesium back into the water using
a commercially available additive like CalMag. Additional
nutrients and cloning mixtures are NOT required at this time, but
you may use !-strength vitamin B-type mixtures such as
Propagator, B52, or SuperThrive. However, these are not
required for great results. Do not exceed the fill line (20L) or
cover the sprinkler heads with water.
4. Attach the 48-site cloning lid to the top of the reservoir and seat
it firmly. Clamp the handles up and over the edge of the lid.
The fit should be snug.
5. Insert 48 of the neoprene discs into the cloning lid. Keep one
extra neoprene disc handy for the first cutting. When inserting
the discs, don’t press them all the way down. Just seat the base
of the discs into the grommets leaving ! in. above the
grommet.
6. Plug in the pump’s power cord and let the machine run for a
minute. Check for water leaks around the grommets on the
side of the cloner near the pump cord and air lines (if air lines
are being used).
7. Take an end cutting, with at least 4-5 nodes, from your host
plant and place the stem in the neoprene disc (the discs open
on the side to allow this placement). Leave at least one,
preferably two nodes, trimmed flush to the stem, below the
bottom end of the disc. Roots will typically grow between the
8/12/2019 Golden Grow® Aeroponic Combo System Manual
http://slidepdf.com/reader/full/golden-grow-aeroponic-combo-system-manual 6/12
6
last two nodes of the cutting. Leave 1-1.5 inches of stem below
the disc.
8. Remove a blank neoprene disc from the lid and swap it with
your newly filled neoprene disc containing the cutting.
9. Repeat steps 7 and 8 for as many cuttings as you wish, up to 48cuttings.
10. Keep the cloner under 18 hours of light per day (18h light / 6h
dark).
11. Check the progress of your clones by first unplugging the pump,
and then carefully slipping the handles off the sides of the lid.
Carefully lift the lid and look for white root formation. After your
inspection, replace the lid, handles, and plug the pump backin.
12. Change the water in the reservoir every 7 days, and in no
longer than 10 days to avoid bacterial growth, fungal growth,
and root rot. This is extremely important.
13. Plants will form roots within 7-28 days, depending on the variety
of the host plant and the health/selection of the cutting. When
the plants have formed fuzzy white roots, select the mostvigorous and healthiest plants and place them gently into your
medium and into your 3.75-in net pots for further vegetative
growth.
New cuttings have been trimmed and placed into their neoprene inserts,
leaving ! inch above the grommet and an inch of stem below the bottom.
8/12/2019 Golden Grow® Aeroponic Combo System Manual
http://slidepdf.com/reader/full/golden-grow-aeroponic-combo-system-manual 7/12
7
Using the System For Vegetative Growth
1. Always start with clean equipment and clean hands. All of the
Golden Grow ® System parts can be cleaned by hand with
simple soap and warm water. Lids, grommets, and reservoirscan be placed into a dishwasher. Cleaning should be done
before every use to reduce the chances of accidentally
growing molds or fungi with your plants.
2. Ensure that your air lines are passing through the reservoir base
and grommets and attach a total of two air stones to the lines.
These air stones are essential for keeping the roots oxygenated
and healthy when the pump is not in operation (if you are using
a timed watering system).
3. Ensure that the pump and manifold are seated firmly in the
center of the reservoir with the long edge of manifold parallel to
the long edge of the reservoir.
4. Fill your reservoir with 12L (approx. 3 gal.) of clean water,
preferably without chlorine or chloramine (a good filtered water
will do). If you use RO or distilled water, be sure to add theappropriate calcium and magnesium back into the water using
a commercially available additive. Additional nutrients may be
added at this time, following the nutrient manufacturer’s
recommended PPM schedule for plants at this stage of growth.
You may also use vitamin B-type mixtures such as Propagator,
B52, or SuperThrive. Do not exceed the fill line (20L) or cover the
sprinkler heads with water.
5. Adjust the pH of the water to 5.8 using commercially available
pH adjusters and pH testers, available online or in your local
hydroponics shop.
6. Attach the 12-site vegetation lid to the top of the reservoir and
seat it firmly. Clamp the handles up and over the edge of the
lid. The fit should be snug.
7. Place your clones/plants into the 3.75-in net pots with yourmedium of choice. If you are using coco coir or any loose
media that may be dislodged from the net pots during
operation, you may wish to use an additional bag filter for the
water pump. This will help ensure the water pump and sprayer
heads don’t become blocked by debris from the grow media.
8/12/2019 Golden Grow® Aeroponic Combo System Manual
http://slidepdf.com/reader/full/golden-grow-aeroponic-combo-system-manual 8/12
8
Make sure to also carefully disassemble and clean your water
pump between cloning cycles. Check the water pump’s
instruction manual (included) for additional details.
8. Place the net pots into the 12 holes in the vegetation lid. Be
sure to cover each of the holes even if there is no plant
available for that location. This will prevent water from
splashing up through the lid when the pump is in operation.
9. Plug in the water pump’s power cord. Optionally, use a timer
(not included) to irrigate the root zone at least 5-10 minutes per
day. You may also leave the pump on full time.
10. Plug in the air pump. The air pump must be running full time.
11. Keep the plants under 18 hours of light per day (18h light / 6hdark) until they reach the desired size and are ready to be
transplanted.
12. Change the water in the reservoir every 7 days, and in no
longer than 10 days to avoid bacterial growth, fungal growth,
and root rot. This is extremely important.
— OPTIONAL —
13. Once the roots have passed through the mesh basket and are
reaching the sprinkler manifold, you may elect to remove the
water pump and manifold. Simply pop out the grommet
holding the pump’s cord, and replace it with the included large
closed grommet to seal the container.
14. Fill the reservoir with 25L (approx. 6.5 gal) of water and nutrients
(PPMs set to the manufacturer’s recommended level for your
plant’s stage of growth) and balance the pH to 5.8. The water
should be no closer than 1 inch from the bottom of the mesh
baskets.
15. Keep in mind that 25L of water weighs a little over 50 pounds
(25kg… the metric system is easy and fun!) so plan aheadbefore you fill your bucket.
16. If you grow your plants for too long in this way, the roots will
become inseparably entwined. Transplant them before this
happens or your plants will suffer shock when transplanted.
8/12/2019 Golden Grow® Aeroponic Combo System Manual
http://slidepdf.com/reader/full/golden-grow-aeroponic-combo-system-manual 9/12
9
Pro Tips
• Be careful not to overgrow your cuttings in the cloner! When
roots have formed, they will grow incredibly quickly in the
cloner, often 2-3 in. per day. Roots really love this environment!Leave them in a few of days too long and your clones will come
out with a foot or more (30+ cm) of root formation. If this
happens, pull apart your medium (if you’re using rock wool)
and gently place the top part of the roots into the middle of the
medium and close it up again, letting the bottom parts of the
roots coil up at the bottom of the net pots and fall through the
holes.
• When cloning, do not unplug your water pump for more than
about 10 min. Roots dry out quickly, and a dried root is a dead
and useless root. Leave your water pump running 24/7 except
when you are changing the water or checking growth.
• Take more cuttings than you need! Even though most if not all
cuttings will grow roots given enough time and proper care,
you’ll want to select the best clones for transplanting.
• Unlike some cloning methods, you don’t need to keep the
cuttings in a super-humid environment nor do you need a
humidity dome. You also don’t need to trim the leaves.
• You do not need special heaters for the cuttings. The heat
generated by the water pump and the lights are more than
enough to keep the cuttings happy if your ambient room
temperature is the recommended 70° F (21° C).
• Use lower levels of lighting (T5 fluorescents, 125w CFLs, etc.) for
new clones to avoid burning or shocking them. Do not place
fresh clones in direct sunlight.
• That capped tee on the manifold? That’s there in case you
want to install a pump-out hose and or valve. The manifold’s
tee is the same size and spec as " in. PVC. With a hose barb
and a slip adapter, the water pump will pump out the water inthe bucket in a few minutes. The sprayers will also flow, so leave
the lid on the reservoir while the water pump is on.
• You can use a clean nylon “footie” over the intake end of the
water pump as an additional filter when using loose media.
8/12/2019 Golden Grow® Aeroponic Combo System Manual
http://slidepdf.com/reader/full/golden-grow-aeroponic-combo-system-manual 10/12
10
Troubleshooting and Support
Cloning
The top of my cloning lid leaks droplets through the neoprene discs.
In cloning mode, you may see a few droplets of water bubble up
from a disc when you first turn on your water pump. This is normal
and will stop quickly. This means that the cloner is balancing the
pressure inside the container. If the droplets don’t stop within a few
moments, remove and replace a neoprene disc to resolve the air
pressure and check again. Also make sure the grommet is installed
properly in the lid.
My clones have been in the clone machine for x days, and they
aren’t growing roots yet.
Different plants clone at different rates. Some plants do not
propagate easily with any cloning method, hydroponic, aeroponic,
or otherwise. Some grow roots within a few days. If you don’t have
much experience cloning a specific plant and you don’t know its
cloning potential, be patient and let it go a bit longer. Change thewater every 7 days and let it go for up to 4 weeks. If you don’t see
roots within 4 weeks, your plant may not be a good candidate for
cloning.
Vegetation
Not all of my grow media in the 3.75 in. net pots are getting
adequately soaked during the watering cycle.
1. Make sure your sprayers are centered in the box. Off-center
placement can mean some baskets will not get enough water.
2. Make sure your spray nozzles are functioning normally, and are
clear of any obstacles or debris.
3. Make sure the cap is on the water pump-out tee.
4. Make sure the water pump chamber is clear of any debris, such
as loose grow media and root matter. Clean the water pump’s
chambers after every cycle.
5. Make sure there is enough water in the reservoir to cover the
water pump, at least 12L (approx. 3 gal.).
8/12/2019 Golden Grow® Aeroponic Combo System Manual
http://slidepdf.com/reader/full/golden-grow-aeroponic-combo-system-manual 11/12
11
1 YEAR LIMITED WARRANTY
This product has been manufactured and tested to the highest quality
standards by Golden Grow, Inc. This Limited Warranty offered by Golden
Grow, Inc. covers defects in material or workmanship in new Golden Grow,
Inc. products. This warranty extends to the original purchaser only and is non-
transferable. Only consumers purchasing Golden Grow, Inc. products from
authorized Golden Grow, Inc. retailers or resellers or through the Golden
Grow, Inc. website may obtain coverage under our limited warranties.
What is covered? Golden Grow, Inc. warrants this product against defects in
material or workmanship as follows:
Golden Grow, Inc. will replace at no charge for parts only or, at its option,
replace any product or part of the product that proves defective because of
improper workmanship and/or material, under normal installation, use, service
and maintenance. If Golden Grow, Inc. is unable to provide a replacementand repair is not practical or cannot be made in a timely fashion, Golden
Grow, Inc. may elect to refund the purchase price in exchange for the return
of the product.
How Long Does The Coverage Last? Our warranty periods are one (1) year
from the documented date of purchase.
What Our Warranty Does Not Cover? Our warranties do not cover any
problem that is caused by:
A. Conditions, malfunctions or damage not resulting from defects in
material or workmanship.
B. Conditions, malfunctions or damage resulting from (1) normal wear and
tear, improper installation, improper maintenance, misuse, abuse,
negligence, accident or alteration.
C. Accessories, connected materials and products, or related products not
manufactured by Golden Grow, Inc.
Our limited warranties are void if a product is returned with damaged or
custom modified components or any alterations (including removal of anystandard components).
How to File a Claim? Golden Grow, Inc. will not provide any warranty
coverage unless claims are made in compliance with all terms of the
controlling warranty statement included with your product and you follow
proper return procedure. To request warranty service, you will need to:
1. Provide the sales receipt or other evidence of the date and place of
purchase.
2. Provide a detailed description of the problem, emailed to
3. Obtain a Return Merchandise Authorization (RMA) Number to use when
returning the product. This number must be clearly marked on the
8/12/2019 Golden Grow® Aeroponic Combo System Manual
http://slidepdf.com/reader/full/golden-grow-aeroponic-combo-system-manual 12/12
exterior shipping packaging of the product. Products returned without
an RMA number will be rejected, returned, or discarded.
4. Deliver the product or the defective part, postage prepaid and carefully
packed and insured, to:
ATTN: WARRANTY REPLACEMENT RMA# [INSERT YOUR RMA# HERE]
GOLDEN GROW, INC.543 COUNTRY CLUB DR STE B # 115
SIMI VALLEY, CA 93065
UNITED STATES
When warranty service is completed, any repaired or replacement product or
part will be returned to you postage prepaid.
REPAIR OR REPLACEMENT (OR, IN LIMITED CIRCUMSTANCES, REFUND OF THE
PURCHASE PRICE) AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE
REMEDY OF THE PURCHASER. GOLDEN GROW, INC. NEITHER ASSUMES NORAUTHORIZES ANY PERSON TO CREATE FOR IT ANY OTHER OBLIGATION OR
LIABILITY IN CONNECTION WITH THIS PRODUCT.
GOLDEN GROW, INC. SHALL NOT BE LIABLE TO PURCHASER OR ANY OTHER
PERSON FOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES,
ARISING OUT OF BREACH OF THIS WARRANTY OR ANY IMPLIED WARRANTY
(INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF
MERCHANTABILITY).
How Does State Law Apply? The laws of the State of California, USA, govern
our warranties. It gives you specific legal rights, and you may also have other
rights that vary from state to state. Our warranties do not affect any additional
rights consumers have under laws in their jurisdictions governing the sale of
consumer goods. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the limitations or exclusions in our
warranty statements may not apply. You may be required by law to give us a
reasonable opportunity to correct or cure any failure to comply before you
can bring any action in court against us under the Magnuson-Moss Warranty
Act.
!"#$%& !(")!
www.goldengrow.com