gns 5890 ads-b
TRANSCRIPT
GNS Electronics GmbH - Adenauerstr. 18, 52146 Würselen – Germany
Tel : +49 2405 4148 – 0 Fax: +49 2405 4148 – 19 www.gns-gmbh.com
GNS 5890 ADS-B Receiver USB Stick
MANUAL
1090 MHz
GNS Electronics GmbH - Adenauerstr. 18, 52146 Würselen – Germany
Tel : +49 2405 4148 – 0 Fax: +49 2405 4148 – 19 www.gns-gmbh.com
- 2 -
General Index
Instruction manual & safety instructions 3
Manuel d'instructions et consignes de sécurité 13
Bedienungsanleitung & Sicherheitsanweisungen 23
GNS Electronics GmbH - Adenauerstr. 18, 52146 Würselen – Germany
Tel : +49 2405 4148 – 0 Fax: +49 2405 4148 – 19 www.gns-gmbh.com
- 3 -
Index
Introduction 4
Safety notices 4
Package contents 5
Specification 5
System requirements 5
Driver installation 5
Driver installation under Windows 7 / 8 6
Software installation 8
adsbSCOPE 9
Remarks to Linux 10
Final clause 10
Copyright 10
Remarks 10
WEEE declaration 11
Warranty notice 11
GNS Electronics GmbH - Adenauerstr. 18, 52146 Würselen – Germany
Tel : +49 2405 4148 – 0 Fax: +49 2405 4148 – 19 www.gns-gmbh.com
- 4 -
Introduction
The GNS 5890 is the worldwide smallest ADS-B receiver with USB
connectivity. All of our products are tested intensively before leaving
the factory. Please read the following information carefully to ensure
a problem-free operation and optimal functionality.
GNS 5890 ADS-B receiver is equipped with a high sensitive
1090 MHz ADS-B circuit.
The GNS 5890 enables the utilisation of the virtual radar system
ADS-B.
Safety notices
Safeguard the GNS 5890 from moisture; observe the limits on
operating and storage temperatures.
Do not expose the GNS 5890 to direct sunlight or heat.
Do not open or modify. Failure to comply will result in the
guarantee and warranty becoming void. There are no
components inside that can be serviced by the user.
Only connect the GNS 5890 to the connector types described
in these instructions.
Be sure to respect the laws of the country you are in with
respect to operation of devices.
Do not operate the GNS 5890 with a damaged cord or if the
unit has dropped and/or has been damaged.
This product is intended for operation with power from a USB
power supply. Other usage is not recommended any may
destroy the device. Please use only the original accessories.
Please remove the protective film from the display
GNS Electronics GmbH - Adenauerstr. 18, 52146 Würselen – Germany
Tel : +49 2405 4148 – 0 Fax: +49 2405 4148 – 19 www.gns-gmbh.com
- 5 -
Package contents
GNS 5890 receiver
ADS-B antenna (antenna base with rod antenna)
This user guide
Driver are on our Web site http://www.gns-gmbh.com
under Support / Software & Driver:
http://www.gns-gmbh.com/index.php?id=117
Should anything be missing, please contact your dealer.
Specification
Support ADS-B 1090 MHz
System requirements
Windows XP/7/8/10
PC or Notebook with free USB 2.0 Port
Pentium 4,
512 MB RAM
VGA Graphics card
Driver Installation
Switch on your computer.
Mount the rod antenna to the antenna base.
Connect the antenna to the ADS-B receiver GNS 5890.
Connect the ADS-B receiver to a free USB port.
Afterwards, Windows displays the Hardware wizard.
Install the GNS 5890 USB driver from our website.
Now the operating system creates a virtual COM port, which is
needed to use the software.
GNS Electronics GmbH - Adenauerstr. 18, 52146 Würselen – Germany
Tel : +49 2405 4148 – 0 Fax: +49 2405 4148 – 19 www.gns-gmbh.com
- 6 -
Driver Installation under Windows 7 / 8
1 INTRODUCTION
This driver patch allows to run the 5890 ADS-B Stick USB on
Windows 7 and Windows 8.
The generic driver had some issues that may cause some instabilities
on some systems.
The installation of the patch has to be performed in some steps that
are described in this manual
Applications
The update procedure described here is intended to ensure a
stable operation of GNS 5890 ADS-B receiver on Win7 and
Win8 systems. No other devices / operating systems are
covered or tested to run with this solution.
remarks
The procedure must be performed manually. Please carefully
follow the instructions step by step. GNS is not liable for any
side effects resulting from unexpected behaviour of your
system.
Please reboot your Computer before performing the patch and
close all running applications before starting.
prerequisites
Your Win7 or Win8 computer
A GNS 5890 ADS-B USB Stick
GNS 5890 driver from our website
http://www.gns-gmbh.com/index.php?id=117
Download GNS 5890 driver package and extract the ZIP
archive in a folder on the computer
Start “setup.exe” from this directory
GNS Electronics GmbH - Adenauerstr. 18, 52146 Würselen – Germany
Tel : +49 2405 4148 – 0 Fax: +49 2405 4148 – 19 www.gns-gmbh.com
- 7 -
2 DRIVER UPDATE PROCEDURE
1. If this is the first time that you install 5890, please first follow
the standard installation process for 5890 from setup menu.
2. Insert your 5890 ADSB receiver to a free USB slot
3. Now Install the modified USB driver for Win 7 & 8 :
a. Open Device Manager from the Control Panel in Windows 7/8. b. With Device Manager open, locate the GNS 5890 ADS-B
Receiver that you want to update the drivers for. c. After finding the hardware you're updating drivers for, right
click on the hardware's name or icon and choose Properties.
In this Properties window, click the Driver tab. d. Click the Update Driver... button.
Note: The Update Driver Software wizard will begin. e. On the How do you want to search for driver software?
Window, click on Browse my computer for driver software.
f. In the next window labeled Browse for driver software on
your computer, click on Let me pick from a list of device drivers on my computer, located at the bottom of the window.
g. Click the Have Disk... button located under the text box. h. Click the Browse... button on the Install From Disk dialog
box that appeared. In the Locate File dialog box that appears next, navigate to the driver folder of the of the extracted
driver and choose „Win7&8_USBdriver_patch” directory.
i. Click any INF file that displays in the file list and click the
Open button. j. The Windows 7 Update Driver Software wizard will now use
the instructions provided in the INF file from Step 10 to
install the updated drivers for your hardware. k. Follow any additional instructions on screen to complete the
driver update.
GNS Electronics GmbH - Adenauerstr. 18, 52146 Würselen – Germany
Tel : +49 2405 4148 – 0 Fax: +49 2405 4148 – 19 www.gns-gmbh.com
- 8 -
Software Installation (adsbSCOPE)
Please install adsbSCOPE from the setup menu on your
computer. Then you can start adsbSCOPE from the desktop
icon or from the windows program menu by one click.
For COM port settings please click to the button “Select COM
Port”
Port : “X” “X” is the virtual COM port of GNS 5890
on your windows system, see page 5
(for example “4” , “6” or other)
Baud Rate : 115.200
After the click at the “Connect” button you will see the data
and position on your screen.
The blue LED in GNS 5890 lights up for every received ADS-B
frame.
COM Port Settings
ADS-B raw data
GNS Electronics GmbH - Adenauerstr. 18, 52146 Würselen – Germany
Tel : +49 2405 4148 – 0 Fax: +49 2405 4148 – 19 www.gns-gmbh.com
- 9 -
adsbSCOPE
adsbSCOPE receives ADS-B-frames from the decoder (via a virtual
COM-port) and decodes the data. It identifies the aircraft and
calculates their positions. All important parameters are shown in
alphanumeric form, in a table and on a graphic display.
adsbSCOPE lists all detected aircraft in a table (right). All aircraft with
known coordinates are show in a graphic display (left).
The graphic display shows:
- the world globe with latitude and longitude - the coastlines of all continents - the position of more then 4000 airports - some big town - tracks of all detected aircraft labeled with altitude, speed,
identifier, heading, squawk... - open-street-map-maps as background image
The outlines and names of all stated of the world can be overlaid
(menu: load Maps). Some of the necessary maps are contained in the
software, the remaining maps can be downloaded and installed
automatically from internet (menu: load Maps -> download maps
from internet).
Runways can be shown as well, if the necessary files were
downloaded from www.jetvision.de .
For setting up the user position turn the map with holding the left
mouse button to the desired current location and fix it with the menu
button "set receiver location" (see picture). Then save your settings
under menu “File” -> “save as” or “save default”.
GNS Electronics GmbH - Adenauerstr. 18, 52146 Würselen – Germany
Tel : +49 2405 4148 – 0 Fax: +49 2405 4148 – 19 www.gns-gmbh.com
- 10 -
Remarks to Linux
The GNS 5890 works under Linux as serial device. But the GNS 5890
must be loaded with the following command: $sudo modprobe usbserial vendor=0x04D8 product=0xF8E8
Final clause
Information and data contained in this manual are subject to change
without notice in advance. Errors and misprints excepted.
Copyright
No part of this manual may be reproduced or transmitted for any purpose, regardless in which way or by which means,
electronically or mechanically, without explicit written approval of GNS Electronics GmbH. The software ADSBscope are © by Jörg Bredendiek licensed under GNU GPLv2 only.
Remarks
For best reception the antenna must have direct view to the sky. The
GNS 5890 is also compatible to PlanePlotter. www.coaa.co.uk/planeplotter.htm
Please use the settings of AVR receiver: Please start PlanePlotter, go to Options --> Mode-S Receiver ---> AVR Receiver --> set COM port Set your COM port to the right value, you can leave the Baudrate as it is 115.200. Now you can also use PlanePlotter with GNS 5890.
Please feel free to contact our support for any further questions by
email: [email protected] or by phone +49 2405 4148 49
Product Website/Forum: www.avionics.gns-gmbh.com
GNS Electronics GmbH - Adenauerstr. 18, 52146 Würselen – Germany
Tel : +49 2405 4148 – 0 Fax: +49 2405 4148 – 19 www.gns-gmbh.com
- 11 -
W E E E d e c l a r a t i o n
This device is labelled in accordance with the European directive
2002/96/EG concerning waste electrical and electronic equipment –
WEEE. The directive sets down a Europe-wide framework for the
return and recycling of end-of-life devices.
WEEE reg. no.: DE 30136236
W a r r a n t y n o t i c e
The product is to be repaired at no cost within the legal warranty
period of 24 months assuming that there is no damage though third-
party interference, moisture, being dropped, or other improper
handling.
Technical Support:
GNS Electronics GmbH
Adenauerstr. 18
D – 52146 Würselen – Germany
Email: [email protected]
Phone: +49 2405 4148 49
Brands, trademarks, product descriptions and logos from third parties
used in these instructions may be trademarks or registered
trademarks of their respective owners.
V 1.7 EU © 2018 by GNS Electronics GmbH Reproduction in whole or
in part only with the permission of GNS Electronics GmbH
Subject to change without notice
Made in Germany
GNS Electronics GmbH - Adenauerstr. 18, 52146 Würselen – Germany
Tel : +49 2405 4148 – 0 Fax: +49 2405 4148 – 19 www.gns-gmbh.com
- 12 -
Notes:
GNS Electronics GmbH - Adenauerstr. 18, 52146 Würselen – Germany
Tel : +49 2405 4148 – 0 Fax: +49 2405 4148 – 19 www.gns-gmbh.com
- 13 -
Index
Introduction 14
Consignes de sécurité 14
Contenu de l'emballage 15
Spécification 15
Exigences du système 15
Installation du pilote 15
Installation des pilotes pour Windows 7 / 8 16
Installation du logiciel 18
adsbSCOPE 19
Note sur Linux 20
Dispositions finales 20
Mentions de copyright 20
Observations finales 20
Déclaration WEEE 21
Note de garantie 21
GNS Electronics GmbH - Adenauerstr. 18, 52146 Würselen – Germany
Tel : +49 2405 4148 – 0 Fax: +49 2405 4148 – 19 www.gns-gmbh.com
- 14 -
Introduction
Le GNS 5890 est le plus petit récepteur dans le monde entier ADS-B
avec une connectivité USB. Tous nos produits sont testés de manière
intensive avant de quitter l'usine. Lisez attentivement les
informations suivantes pour assurer un fonctionnement sans
problème et une fonctionnalité optimale.
GNS 5890 ADS-B récepteur est équipé d'un circuit à haute sensibilité
pour 1090 MHz ADS-B.
Le GNS 5890 permet l'utilisation du système de radar virtuel ADS-B.
Consignes de sécurité
Protéger le GNS 5890 de l'humidité; observer les limites de
températures de fonctionnement et de stockage.
Ne pas exposer le GNS 5890 à la lumière du soleil ou à la
chaleur.
Ne pas ouvrir ou modifier. Le non-respect se traduira par
l’annulation de la garantie. Il n'y a aucun composant à
l'intérieur qui peut être réparé par l'utilisateur.
Connecter uniquement le GNS 5890 aux types de connecteurs
décrits dans ces instructions.
Assurez-vous de respecter les lois du pays où vous êtes en ce
qui concerne le fonctionnement des dispositifs.
Ne pas utiliser le GNS 5890 avec un cordon endommagé ou si
l'appareil est tombé et / ou a été endommagé.
Ce produit est prévu pour fonctionner avec la puissance d'une
alimentation USB. Toute autre utilisation n'est pas
recommandée, celà pourrait détruire l'appareil. Utilisez
uniquement les accessoires d'origine.
Enlevez s'il vous plaît le film protecteur de l'écran
GNS Electronics GmbH - Adenauerstr. 18, 52146 Würselen – Germany
Tel : +49 2405 4148 – 0 Fax: +49 2405 4148 – 19 www.gns-gmbh.com
- 15 -
Contenu de l'emballage
GNS 5890 récepteur
ADS-B antenne (base de l'antenne avec antenne tige)
Ce mode d'emploi
Pilote sur notre site http://www.gns-gmbh.com
sous Support / Software & Driver:
http://www.gns-gmbh.com/index.php?id=117
Si quelque chose est manquant, contactez s'il vous plaît votre
revendeur.
Spécification
Soutien ADS-B 1090 MHz
Exigences du système
Windows XP/7/8/10
PC ou ordinateur portable avec connexion USB 2.0
Pentium 4,
512 MB RAM
Carte graphique VGA
L'installation du pilote
Allumez votre ordinateur.
Fixez l'antenne tige à la base de l'antenne.
Connectez l'antenne au récepteur ADS-B GNS 5890.
Connectez le récepteur ADS-B à un port USB libre.
Ensuite, Windows affiche l'assistant matériel.
Installez le pilote USB de GNS 5890 de notre site Web.
A présent va se créer un port COM virtuel, qui est nécessaire
pour utiliser le logiciel.
GNS Electronics GmbH - Adenauerstr. 18, 52146 Würselen – Germany
Tel : +49 2405 4148 – 0 Fax: +49 2405 4148 – 19 www.gns-gmbh.com
- 16 -
Installation des pilotes sous Windows 7/8
1 INTRODUCTION
Ce correctif de pilote permet d’exécuter l’ADS_B Stick USB 5890 sur
Windows 7 et Windows 8.
Le pilote générique a eu quelques problèmes, ce qui est la cause de
certaines instabilités sur certains systèmes.
L'installation du patch doit être effectuée en quelques étapes qui sont
décrites dans ce manuel.
Applications
L’update Procédure décrit ici est destiné à assurer une stabilité
opérationnelle de GNS 5890 ADS-B récepteur sur Win7 et
Win8 système. Pas d'autres dispositifs / systèmes
d'exploitation sont couverts ou testés pour fonctionner avec
cette solution.
Remarks
La procédure doit être effectuée manuellement. Suivez s'il
vous plaît les instructions de soins entièrement étape par
étape. GNS n'est pas responsable des effets secondaires
résultant d'un comportement inattendu de votre système.
Redémarrez votre ordinateur avant d'effectuer le correctif et
fermez toutes les applications en cours d'exécution avant de
commencer.
Prérequis
Votre ordinateur Win7 ou Win8
Un GNS 5890 ADSB Stick USB
GNS 5890 pilote à partir de notre site Web
http://www.gns-gmbh.com/index.php?id=117
Télécharger GNS package de pilote 5890 et extraire l'archive
ZIP dans un dossier sur l'ordinateur
Lancer le fichier "setup.exe" à partir de ce répertoire
GNS Electronics GmbH - Adenauerstr. 18, 52146 Würselen – Germany
Tel : +49 2405 4148 – 0 Fax: +49 2405 4148 – 19 www.gns-gmbh.com
- 17 -
2 Pilote procédure de mise à jour
1. Si c'est la première fois que vous installez 5890, suivez
d'abord la procédure d'installation standard pour 5890 à partir du
menu de configuration.
2. Insérez votre ADSB récepteur 5890 à un port USB libre
3. Maintenant Installez le pilote USB modifié pour Win 7/8/10:
a. Ouvrez le Gestionnaire de périphériques dans le Panneau de configuration dans Windows 7/8.
b. Avec le Gestionnaire de périphériques ouvert, recherchez le GNS 5890 ADS-B récepteur que vous souhaitez et activez en cliquant une fois sur le bouton.
c. Mettez alors à jour les pilotes par un double clic sur le nom ou l'icône du matériel et sélectionnez « Propriétés ». Dans cette fenêtre, cliquez sur la case d’option « Pilote ».
d. Cliquez sur le bouton « mettre à jour le pilote ». Remarque: L'assistant de mise à jour logicielle du pilote commencera.
e. Sur la page « Comment voulez-vous rechercher un pilote logiciel? » Fenêtre, cliquez sur Parcourir mon ordinateur pour logiciel pilote.
f. Dans la fenêtre suivante, marquez « Parcourir un pilote logiciel » sur votre ordinateur, cliquez sur « Me laisser choisir parmi une liste de pilotes de périphériques sur mon ordinateur », situé au bas de la fenêtre.
g. Cliquez sur le Disque ... bouton situé sous la zone de texte. h. Cliquez sur le bouton Parcourir ... bouton "Installer à partir du
disque" boîte de dialogue qui apparaît. Dans la boîte de dialogue Rechercher le fichier qui apparaît à côté, accédez au dossier que vous avez extrait dans le cadre du téléchargement de pilote et choisir le dossier "Win7 & 8_USBdriver_patch".
i. Cliquez sur un fichier INF qui s'affiche dans la liste des fichiers et cliquez sur le bouton Ouvrir.
j. L'assistant de Windows 7 Software Update Driver va maintenant utiliser les instructions fournies dans le fichier INF de l'étape 10 pour installer les pilotes mis à jour pour votre matériel.
k. Suivez les instructions supplémentaires sur l'écran pour terminer la mise à jour du pilote.
GNS Electronics GmbH - Adenauerstr. 18, 52146 Würselen – Germany
Tel : +49 2405 4148 – 0 Fax: +49 2405 4148 – 19 www.gns-gmbh.com
- 18 -
Installation du logiciel (adsbSCOPE)
S'il vous plaît installer adsbSCOPE dans le menu de
configuration sur votre ordinateur. Ensuite, vous pouvez
commencer adsbSCOPE de l'icône du bureau ou du menu du
programme Windows en un seul clic.
Pour les réglages du port COM cliquez sur le bouton «Select
COM Port»
Port : “X” “X” est le port COM virtuel de GNS 5890
sur votre système Windows, voir la page
15 (par exemple “4” , “6” ou autre)
Baud Rate : 115.200
Après le clic sur le bouton "Connect", vous verrez les données
et la position sur l'écran.
La LED bleue en GNS 5890 s'allume pour chaque trame reçue
ADS-B.
COM Port
Settings
ADS-B raw data
GNS Electronics GmbH - Adenauerstr. 18, 52146 Würselen – Germany
Tel : +49 2405 4148 – 0 Fax: +49 2405 4148 – 19 www.gns-gmbh.com
- 19 -
adsbSCOPE
adsbSCOPE reçoit ADS-B-cadres du décodeur (via un port COM
virtuel) et décode les données. Il identifie l'avion et calcule leurs
positions. Tous les paramètres importants sont présentés sous forme
alphanumérique, dans le tableau et écran graphique.
adsbSCOPE répertorie tous les aéronefs détectés dans un tableau (à
droite). Tous les avions aux coordonnées connues sont montrés dans
un affichage graphique (à gauche).
Le graphique montre:
- Le globe du monde avec la latitude et la longitude - Les côtes de tous les continents - La position de plus de 4000 aéroports - Certaines grandes villes - Pistes de tous les aéronefs détectés marqués avec l'altitude, la vitesse, identificateur, titre, bruit ...
- OpenStreetMap-carte comme une image de fond
Les grandes lignes et les noms de tous les Etats du monde peuvent
être superposées (Menu: load Maps). Certaines des cartes
nécessaires sont contenues dans le logiciel, les cartes restantes
peuvent être téléchargées et installées automatiquement à partir
d'Internet (Menu: load Maps -> download maps from internet).
Runways peuvent être montrés ainsi, les fichiers nécessaires étant
été téléchargés auparavant sur www.jetvision.de.
Pour définir la position de la GNS 5890 sur la carte, faire pivoter la
carte avec le bouton gauche de la souris sur la position actuelle
souhaitée, fixer avec l'élément de menu "set receiver location" (voir
illustration) et enregistrer la position du point de menu "Fichier" ->
"save position" ou "save default".
GNS Electronics GmbH - Adenauerstr. 18, 52146 Würselen – Germany
Tel : +49 2405 4148 – 0 Fax: +49 2405 4148 – 19 www.gns-gmbh.com
- 20 -
Note sur Linux
Le GNS 5890 fonctionne sous Linux en série périphérique. Mais le
GNS 5890 doit être chargé avec la commande suivante: $sudo modprobe usbserial vendor=0x04D8 product=0xF8E8
Dispositions finales
Les informations et données contenues dans ce manuel sont sujettes
à modification sans préavis. Sauf erreurs et fautes d'impression
Mentions de copyright
Aucune partie de ce manuel ne peut être reproduite ou transmise à
quelque fin, indépendamment de quelle façon ou par quel moyen,
électronique ou mécanique, sans la permission écrite de GNS
Electronics GmbH. Le ADSBscope logiciel sont © par Jörg Bredendiek sous licence GNU GPLv2 seulement.
Observations finales
Pour une meilleure réception, l'antenne doit disposer d’une vue
directe sur le ciel. Le GNS 5890 est aussi compatible à PlanePlotter. www.coaa.co.uk/planeplotter.htm
Utilisez les réglages de récepteur AVR:
S'il vous plaît commencer PlanePlotter, aller à Options --> Mode-S Receiver ---> AVR Receiver --> set COM port Définir votre port COM à la juste valeur, vous pouvez laisser la vitesse de transmission comme il est 115.200. Maintenant, vous pouvez également utiliser PlanePlotter avec GNS 5890.
S'il vous plaît n'hésitez pas à contacter notre support pour d'autres
questions par e-mail: [email protected] ou par téléphone +49
2405 4148 49 Produit Site Web/Forum: www.avionics.gns-gmbh.com
GNS Electronics GmbH - Adenauerstr. 18, 52146 Würselen – Germany
Tel : +49 2405 4148 – 0 Fax: +49 2405 4148 – 19 www.gns-gmbh.com
- 21 -
D é c l a r a t i o n D E E E
Cet appareil est marqué conformément à la directive européenne
2002/96/CE relative aux équipements de déchets électriques et
électroniques - DEEE. La directive définit le cadre en vigueur pour la
collecte et le recyclage des appareils usagés dans l'UE.
DEEE reg. pas. DE 30136236
N o t e d e g a r a n t i e
Le produit peut être réparé sans frais pendant la période de garantie
légale de 24 mois en supposant qu'il n'y ait pas de dommages dus à
l'ingérence de tiers, à l'humidité, à une chute ou autre mauvaise
manipulation.
Support Technique:
GNS Electronics GmbH
Adenauerstr. 18
D – 52146 Würselen – Allemagne
Email: [email protected]
Téléphone: +49 2405 4148 49
Les marques, les noms commerciaux descriptions de produits et logos
de tiers utilisés dans ce document peuvent être des marques
commerciales ou des marques déposées de leurs propriétaires
respectifs.
V 1.7 EU © 2018 GNS Electronics GmbH reproduction en tout ou en
partie qu'avec l'autorisation de GNS Electronics GmbH
Sous réserve de modifications sans préavis
Fabriqué en Allemagne
GNS Electronics GmbH - Adenauerstr. 18, 52146 Würselen – Germany
Tel : +49 2405 4148 – 0 Fax: +49 2405 4148 – 19 www.gns-gmbh.com
- 22 -
Remarque :
GNS Electronics GmbH - Adenauerstr. 18, 52146 Würselen – Germany
Tel : +49 2405 4148 – 0 Fax: +49 2405 4148 – 19 www.gns-gmbh.com
- 23 -
Index
Einleitung 24
Sicherheitshinweise 24
Packungsinhalt 25
Spezifikationen 25
Systemvoraussetzungen 25
Treiberinstallation 25
Treiberinstallation unter Windows 7 / 8 26
Softwareinstallation 28
adsbSCOPE 29
Anmerkung zu Linux 30
Schlussbestimmungen 30
Copyright-Hinweis 30
Abschlussbemerkung 30
WEEE Deklaration 31
Garantiehinweis 31
GNS Electronics GmbH - Adenauerstr. 18, 52146 Würselen – Germany
Tel : +49 2405 4148 – 0 Fax: +49 2405 4148 – 19 www.gns-gmbh.com
- 24 -
Einleitung
Der GNS 5890 ist der weltweit kleinste ADS-B-Receiver mit USB-
Anschluss. Alle unsere Produkte werden intensiv vor dem Verlassen
des Werkes getestet. Bitte lesen Sie die folgenden Informationen
sorgfältig durch, um eine problemlose Bedienung und optimale
Funktionalität zu gewährleisten.
GNS 5890 ADS-B-Receiver ist mit einer hoch empfindlichen 1090 MHz
ADS-B-Empfangseinheit ausgestattet.
Der GNS 5890 ermöglicht die Nutzung des virtuellen Radarsystem
ADS-B.
Sicherheitshinweise
Schützen Sie den GNS 5890 vor Feuchtigkeit und halten Sie
die Betriebs- und Aufbewahrungstemperaturlimits ein.
Setzen Sie den GNS 5890 nicht direktem Sonnenlicht oder
Hitze aus.
Öffnen oder modifizieren Sie den GNS 5890 nicht. Bei
Nichtbeachtung verfallen die Garantie- und Gewährleistungs-
Ansprüche. Im Innern des GNS 5890 sind keine Teile, die
durch den Benutzer gewartet werden können.
Schließen Sie den GNS 5890 nur an die in der Anleitung
angegebenen Anschlüsse an.
Vergewissern Sie sich, dass Sie die Gesetze des Landes
bezüglich der Benutzung von Geräten einhalten, im dem Sie
sich befinden.
Betreiben Sie das GNS 5890 nicht mit beschädigtem Kabel
oder nachdem es heruntergefallen und/oder beschädigt
worden ist.
Dieses Produkt ist für den Betrieb an einer Stromversorgung
aus einem USB-Port vorgesehen. Eine andere Verwendung
wird nicht empfohlen, jede andere kann das Gerät zerstören.
Bitte verwenden Sie nur das Original-Zubehör.
Bitte entfernen Sie die Schutzfolie vom Display
GNS Electronics GmbH - Adenauerstr. 18, 52146 Würselen – Germany
Tel : +49 2405 4148 – 0 Fax: +49 2405 4148 – 19 www.gns-gmbh.com
- 25 -
Packungsinhalt
GNS 5890-Empfänger
ADS-B-Antenne (Antennenfuß mit Stabantenne)
Diese Bedienungsanleitung
Gerätetreiber finden Sie auf unserer Web-Seite
http://www.gns-gmbh.com unter Support / Software & Treiber
http://www.gns-gmbh.com/index.php?id=117
Sollte etwas fehlen, wenden Sie sich bitte direkt an Ihren Händler.
Spezifikationen
Unterstützt ADS-B 1090 MHz
Systemvoraussetzungen
Windows XP / 7 / 8 / 10
PC oder Notebook mit einem freien USB 2.0 Port
Pentium 4, und schneller
mindestens 512 MB RAM
VGA-Grafikkarte
Treiber-Installation
Schalten Sie Ihren Windows-Computer ein.
Montieren Sie die Stabantenne auf den ADS-B-Antennenfuß.
Verbinden Sie die ADS-B-Antenne mit dem GNS 5890.
Schließen Sie den ADS-B-Receiver GNS 5890 an einen freien
USB-Port Ihres Windows-Computers an.
Der GNS 5890 wird von Windows erkannt und es startet der
Hardware-Manager.
Installieren Sie bitte den 5890 USB-Treiber von unserer
Webseite (s.o.)
Es wird nun ein virtueller COM-Port für die GNS 5890 auf
Ihrem PC erzeugt, den Sie in der Software (s.u.) als Anschluss
für den GNS 5890 angeben müssen.
GNS Electronics GmbH - Adenauerstr. 18, 52146 Würselen – Germany
Tel : +49 2405 4148 – 0 Fax: +49 2405 4148 – 19 www.gns-gmbh.com
- 26 -
Treiber-Installation unter Windows 7 / 8 / 10
1 Einleitung
Dieser Treiber-Patch ermöglicht den stabilen Betrieb des GNS 5890
ADS-B-USB-Sticks unter Windows 7 / 8 /10.
Denn der generische Treiber verursachte einige Probleme, welche die
Ursache für einige Instabilitäten des Betriebsystems waren.
Die Installation des Patches wird in wenigen Schritten durchgeführt,
die im Folgenden in diesem Manual beschrieben werden.
Anwendungen
Der hier beschriebene Update-Vorgang soll einen stabilen
Betrieb des GNS 5890 ADS-B-Empfänger unter Windows
7/8/10 -Systemen gewährleisten. Keine anderen Geräte /
Betriebssysteme sind von dieser Lösung betroffen oder wurden
getestet.
Bemerkungen
Dieses Update muss manuell durchgeführt werden. Bitte
beachten Sie unbedingt die Schritt-für-Schritt-Anweisungen.
GNS haftet nicht für irgendwelche Schäden, die zu einem
unerwarteten Verhalten Ihres Systems führen. Bitte starten
Sie zuerst Ihren Computer neu und beenden Sie alle laufenden
Programme bevor Sie mir dem Treiber-Patch beginnen.
Voraussetzung
Ihr Windows 7/8/10 - Computer
GNS 5890 ADS-B-USB-Stick
GNS 5890 Treiber von unserer Web-Seite
http://www.gns-gmbh.com/index.php?id=117
Laden Sie das GNS 5890 Treiberpaket von unserer Web-Seite
auf Ihren PC und entpacken das ZIP-Archiv in ein Verzeichnis.
Starten Sie aus diesem Verzeichnis „setup.exe“
GNS Electronics GmbH - Adenauerstr. 18, 52146 Würselen – Germany
Tel : +49 2405 4148 – 0 Fax: +49 2405 4148 – 19 www.gns-gmbh.com
- 27 -
2 Treiber-Update-Prozedur
4. Wenn der GNS 5890 zum ersten Mal installiert wird, folgen Sie
bitte dem Installations-Prozess vom Setup-Menü.
5. Stecken Sie anschließend Ihren GNS 5890 ADS-B Receiver in
eine freie USB-Buchse.
6. Jetzt installieren Sie den modifizierten USB-Treiber für Win
7/8/10 folgendermaßen:
a. Öffnen Sie den Geräte-Manager in dem System-Fenster von
Windows 7/8/10 (dies wird gestartet mit gleichzeitig
gedrückter Windows-Taste & Pause-Taste). b. Im geöffneten Geräte-Manager, den GNS 5890 ADS-B
Receiver-Namen finden und durch einen Klick auswählen. c. Mit Doppelklick auf den GNS 5890-Namen das
„Eigenschaften-Fenster“ des GNS 5890 aufrufen und die Registerkarte „Treiber“ mit einem Klick auswählen.
d. Klicken Sie dann auf den „Treiber aktualisieren...“ Knopf. Das Treiber-Update-Programm startet jetzt.
e. Im Menü „Treibersoftware aktualisieren...“ klicken Sie auf „Auf den Computer nach Treibersoftware suchen“.
f. Im nächsten Fenster, überschrieben mit “An diesem Ort nach Treibersoftware suchen”, wählen Sie “Durchsuchen“ aus. Klicken Sie nun auf den “Durchsuchen...”-Knopf unten.
g. Im jetzt erscheinenden „Ordner suchen“-Fenster wählen Sie das Verzeichnis aus, im dem Sie die Treiber entpackt haben und wählen Sie „Win7&8_USBdriver_patch“ aus und bestätigen Sie dies mit dem OK-Knopf.
h. Nun klicken Sie im vorherigen Fenster auf „Weiter“. i. Die Windows Treiber-Update-Routine wird jetzt den
Anweisungen in der INF-Datei folgend den aktualisierten
Treiber für die Hardware installieren. j. Folgen Sie bitte den zusätzlichen Anweisungen auf dem
Bildschirm, um das Treiber-Update erfolgreich zu vervollständigen.
GNS Electronics GmbH - Adenauerstr. 18, 52146 Würselen – Germany
Tel : +49 2405 4148 – 0 Fax: +49 2405 4148 – 19 www.gns-gmbh.com
- 28 -
Software-Installation (adsbSCOPE)
Bitte installieren Sie adsbSCOPE über das Setup-Menü auf
Ihrem Computer. Anschließend können Sie adsbSCOPE über
das Desktop-Icon oder aus dem Windows-Programm-Menü mit
einem Klick starten.
Für die COM-Port-Einstellungen klicken Sie auf die Schaltfläche
„Select COM Port“.
Port : “X” “X” ist der virtuelle COM-Port des GNS
5890 auf dem Windows-System, siehe
Seite 25 (zum Beispiel “4” , “6”).
Baud Rate : 115.200
Nach einem Klick auf den “Connect”-Knopf werden die
empfangenen Datensätze auf dem Bildschirm sichtbar.
Die blaue LED des GNS 5890 leuchtet bei jedem empfangenen
ADS-B-Frame auf.
COM Port Settings
ADS-B raw data
GNS Electronics GmbH - Adenauerstr. 18, 52146 Würselen – Germany
Tel : +49 2405 4148 – 0 Fax: +49 2405 4148 – 19 www.gns-gmbh.com
- 29 -
adsbSCOPE
adsbSCOPE übernimmt die empfangenen Daten des Decoders an der
(virtuellen) COM-Schnittstelle und decodiert sie.
adsbSCOPE listet alle empfangenen Flugzeuge in einer Tabelle auf
(rechte Seite). Alle Flugzeuge mit bekannten Koordinaten werden in
der linken Kartenansicht dargestellt.
Dargestellt werden:
- die gesamte Welt mit Breiten- und Längengraden - die Küstenlinien aller Kontinente - die Position von über 4000 Flughäfen - die Position einiger wichtiger Städte - die Flugbahnen aller lokalisierten Flugzeuge mit Flughöhe und Geschwindigkeit - wenn vorhanden: Kennung und Typ des Flugzeugs
- open-street-map-Karten als Hintergrundbild
Es können zusätzlich Ländergrenzen und Namen fast aller Länder der
Welt eingeblendet werden (Menü: load Maps).
Einige der dazu nötigen Karten sind im Lieferumfang enthalten,
weitere Karten können auf Wunsch automatisch aus dem Internet
heruntergeladen und installiert werden (Menü: load Maps ->
download maps from Internet).
Die Lage von Start- und Landebahnen können dargestellt werden,
wenn die nötigen Dateien von www.jetvision.de heruntergeladen
werden.
Um die Position des GNS 5890 auf der Karte festzulegen, drehen
Sie den Kartenausschnitt mit gedrückter linker Maustaste auf die
gewünschte aktuelle Position, fixieren diese mit dem Menü-Punkt
“set receiver location” (siehe Abbildung) und speichern die Position über den Menü-Punkt “File” -> “save position” oder “save default”.
GNS Electronics GmbH - Adenauerstr. 18, 52146 Würselen – Germany
Tel : +49 2405 4148 – 0 Fax: +49 2405 4148 – 19 www.gns-gmbh.com
- 30 -
Anmerkung zu Linux
Der GNS 5890 kann unter Linux als virtuelles serielles Gerät
verwendet werden. Dafür muß der GNS 5890 mit folgendem
Kommando geladen werden: $sudo modprobe usbserial vendor=0x04D8 product=0xF8E8
Schlussbestimmungen
Informationen und technische Daten in diesem Handbuch können
ohne vorherige Ankündigung geändert werden. Irrtümer und
Druckfehler vorbehalten.
Copyright-Hinweis
Dieses Handbuch oder Teile daraus dürfen nicht ohne ausdrückliche
schriftliche Genehmigung der GNS Electronics GmbH in jeglicher Art
und Weise, ob elektronisch oder mechanisch, kopiert oder übertragen
werden.
Die Software ADSBscope ist © von Jörg Bredendiek und lizenziert unter GNU GPLv2.
Abschlussbemerkung
Für den optimalen Empfang muss die ADS-B-Antenne eine freie Sicht
zum Himmel haben. Der GNS 5890 ist auch kompatibel zur Software PlanePlotter: www.coaa.co.uk/planeplotter.htm
Dabei sind die Einstellungen des AVR-Receivers zu verwenden: Bitte starten Sie PlanePlotter und öffnen Sie den Menü-Punkt Options --> Mode-S Receiver ---> AVR Receiver --> set COM port. Stellen Sie den COM-Port auf entsprechenden Wert und belassen Sie die Baudrate bei 115,200. Jetzt können Sie die Software PlanePlotter mit dem GNS 5890 verwenden.
Zögern Sie nicht bei weiteren Fragen sich mit unserem Support in
Verbindung zu setzen, entweder über eine E-Mail an: support@gns-
gmbh.com oder über Telefon: +49 2405 4148 49. Unsere Produkt-
Webseite mit Forum lautet: http://www.avionics.gns-gmbh.com
GNS Electronics GmbH - Adenauerstr. 18, 52146 Würselen – Germany
Tel : +49 2405 4148 – 0 Fax: +49 2405 4148 – 19 www.gns-gmbh.com
- 31 -
WEEE Deklaration
Dieses Gerät ist entsprechend der europäischen Richtlinie
2002/96/EG über Elektro- und Elektronikkaltgeräte (waste electrical
and electronic equipment - WEEE) gekennzeichnet. Die Richtlinie gibt
den Rahmen für eine EU-weit gültige Rücknahme und Verwertung der
Altgeräte vor. WEEE-Reg.-Nr. DE 30136236
G a r a n t i e h i n w e i s
Das Produkt wird innerhalb der gesetzlichen Garantiezeit von 24
Monaten kostenlos instand gesetzt, sofern keine Einwirkungen durch
Fremdeingriff, Feuchtigkeit, Sturz oder andere Beschädigung durch
unsachgemäße Handhabung vorliegen.
Technischer Support:
GNS Electronics GmbH
Adenauerstr. 18
D – 52146 Würselen – Germany
Email: [email protected]
Tel.: +49 2405 4148 49
Marken, Handelsnamen, Produktbezeichnungen und Logos Dritter, die
in dieser Anleitung verwendet werden, sind möglicherweise Marken
oder eingetragene Marken der jeweiligen Rechtsinhaber.
V 1.7 EU © 2018 by GNS Electronics GmbH Nachdruck, auch
auszugsweise, nur mit Genehmigung der GNS Electronics GmbH
Technische Änderungen vorbehalten
Made in Germany
GNS Electronics GmbH - Adenauerstr. 18, 52146 Würselen – Germany
Tel : +49 2405 4148 – 0 Fax: +49 2405 4148 – 19 www.gns-gmbh.com
- 32 -
Notizen: