gmbh certificate d pl - dakks · annex to the accreditation certificate d ‐pl ... testing...
TRANSCRIPT
This document is a translation. The definitive version is the original German annex to the accreditation certificate.
1/52
Deutsche Akkreditierungsstelle GmbH Annex to the Accreditation Certificate D‐PL‐11117‐01‐00 according to DIN EN ISO/IEC 17025:2005 Period of validity: 08.09.2015 until 10.04.2019 Date of issue: 08.09.2015
Holder of certificate:
TÜV Rheinland LGA Bautechnik GmbH Prüfstelle Baustoffe und Beton, Verkehrswegebau, Werkstoffe Tillystraße 2, 90431 Nürnberg Tests in the fields:
Testing of concrete and grout, cement, admixtures‐ and additives for concrete and grout, se‐lected aggregates for concrete and grout, floor screed, building bricks, aerated and lightweight concrete, concrete goods, artificial stone, drainage goods, insulating materials, ceilings, wooden building components, material and construction element testing ‐ Tests of mineral construction materials and natural stone ‐ Geotechnical ‐ ground and soil investiga‐tions, sampling and testing of soils, rock and aggregate samples ‐ Testing of bituminous mate‐rials, road marking materials, coatings as well as hot‐ and cold plastic masses ‐ non‐destructive testing of road surfaces and road areas ‐ mechanical structural test methods, tests of rein‐forcing steel, dynamic materials and components testing, testing of weld seams of metallic materials, metallographic and corrosion testing Test methods (investigation area I and special test methods of investigation area II) by third party testing authorities for the installation of mineral construction materials in landfill liner systems according to the Landfill Ordinance ‐ DepV and Federal Uniform Quality Standard BQS 9‐1 Testing of construction products and testing of fire resistance within the framework of EU Regulation No. 305/2011 laying down the harmonised conditions for the marketing of con‐struction products (Construction Products Regulation ‐ CPR) Abbreviations used: see last page
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 2/52Date of issue: 08.09.2015
The testing laboratory is permitted, without being required to inform and obtain prior ap‐proval from DAkkS, to use standard testing methods listed here with different issue dates. This is valid for all areas of accreditation scope with the exception of section 4 (CPR). 1 Tests of concrete adhesives, concrete, grout, floor screed, building bricks and masonry,
admixtures and additives, mineral building products and natural stones 1.1 Binders and concrete DIN EN 196‐1 2005‐05
Methods of testing cement ‐ Part 1: Determination of strength ‐
DIN EN 196‐2 2013‐10
Method of testing cement ‐ Part 2: Chemical analysis of cement
DIN EN 196‐3 2009‐02
Methods of testing cement ‐ Part 3: Determination of setting times and soundness
DIN EN 196‐6 2010‐05
Methods of testing cement ‐ Part 6: Determination of fineness
DIN EN 196‐7 2008‐02
Methods of testing cement ‐ Part 7: Methods of taking and pre‐paring samples of cement
The above listed standards are to be used in connection with the follow‐ing guidance documents:
DIN EN 197‐1 2011‐11
Cement ‐ Part 1: Composition, specifications and conformity criteria for common cements
DIN EN 197‐2 2012‐01
Cement ‐ Part 2: Conformity evaluation
DIN EN 450‐1 2012‐10
Cement ‐ Part 1: Composition, specifications and conformity criteria for common cements
DIN EN 451‐2 1995‐01
Method of testing fly ash ‐ Part 2: Determination of fineness by wet sieving
DIN EN 1015‐3 2007‐05
Methods of test for mortar for masonry ‐ Part 3: Determination of consistence of fresh mortar (by flow table)
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 3/52Date of issue: 08.09.2015
DIN EN 13454‐2 2007‐11
Binders, composite binders and factory made mixtures for floor screeds based on calcium sulfate ‐ Part 2: Test methods
in connection with:
DIN EN 13454‐1 2005‐1
Binders, composite binders and factory made mixtures for floor screeds based on calcium sulfate ‐ Part 1: Definitions and requirements
DIN EN 413‐2 2005‐08
Masonry cement ‐ Part 2: Test methods
DIN EN 520 2009‐12
Gypsum plasterboards ‐ Definitions, requirements and test methods
DIN 51043 1979‐08
Trass ‐ Requirements, Tests
DIN EN 480‐1 2011‐09
Admixtures for concrete, mortar and grout ‐ Test methods ‐ Part 1: Reference concrete and reference mortar for testing
DIN EN 480‐2 2006‐11
Admixtures for concrete, mortar and grout ‐ Test methods ‐ Part 2: Determination of setting time
DIN EN 480‐4 2006‐03
Admixtures for concrete, mortar and grout ‐ Test methods ‐ Part 4: Determination of bleeding of concrete
DIN EN 480‐11 2005‐12
Admixtures for concrete, mortar and grout ‐ Test methods ‐ Part 11: Determination of air void characteristics in hardened concrete
DIN EN 934‐6 2006‐03
Admixtures for concrete, mortar and grout ‐ Part 6: Sampling, conformity control and evaluation of conformity
The above listed standards are to be used in connection with the follow‐ing guidance documents:
DIN EN 12518 2008‐04
Chemicals used for treatment of water intended for human consumption ‐ High‐calcium lime
DIN EN 445 2008‐01
Grout for prestressing tendons ‐ Test methods
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 4/52Date of issue: 08.09.2015
DIN EN 12350‐1 2009‐08
Testing fresh concrete ‐ Part 1: Sampling
DIN EN 12350‐2 2009‐08
Testing fresh concrete ‐ Part 2: Slump‐test
DIN EN 12350‐3 2009‐08
Testing fresh concrete ‐ Part 3: Vebe test
DIN EN 12350‐4 2009‐08
Testing fresh concrete ‐ Part 4: Degree of compactibility
DIN EN 12350‐5 2009‐08
Testing fresh concrete ‐ Part 5: Flow table test
DIN EN 12350‐6 2011‐03
Testing fresh concrete ‐ Part 6: Density
DIN EN 12350‐7 2009‐08
Testing fresh concrete ‐ Part 7: Air content ‐ Pressure methods
DIN EN 12350‐8 2010‐12
Testing fresh concrete ‐ Part 8: Self‐compacting concrete ‐ Slump‐flow test
DIN EN 12350‐11 2010‐12
Testing fresh concrete ‐ Part 11: Self‐compacting concrete ‐ Sieve segregation test
DIN EN 12350‐12 2010‐12
Testing fresh concrete ‐ Part 12: Self‐compacting concrete ‐ J‐ring test
DIN EN 12504‐1 2009‐07
Testing concrete in structures ‐ Part 1: Cored specimens ‐ Taking, examining and testing in compression
DIN EN 12504‐2 2012‐12
Testing concrete in structures ‐ Part 2: Non‐destructive testing ‐ Determination of rebound number
DIN 1048‐5 1991‐06
Testing concrete ‐ testing of hardened concrete (specimens pre‐pared in mould)
DIN EN 12390‐1 2012‐12
Testing hardened concrete ‐ Part 1: Shape, dimensions and other requirements for specimens and moulds
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 5/52Date of issue: 08.09.2015
DIN EN 12390‐2 2009‐08 + Corrigenda 1 2012‐02
Testing hardened concrete ‐ Part 2: Making and curing specimens for strength tests
DIN EN 12390‐3 2009‐07 + Corrigenda 1 2011‐11
Testing hardened concrete ‐ Part 3: Compressive strength of test specimens (withdrawn standard)
DIN EN 12390‐5 2009‐07
Testing hardened concrete ‐ Part 5: Flexural strength of test specimens
DIN EN 12390‐6 2010‐09
Testing hardened concrete ‐ Part 6: Tensile splitting strength of test specimens
DIN EN 12390‐7 2009‐07
Testing hardened concrete ‐ Part 7: Density of hardened concrete
DIN EN 12390‐8 2009‐07
Testing hardened concrete ‐ Part 8: Depth of penetration of water under pressure
ZTV‐Ing, Teil 1 2012‐03
Additional terms of contract and guidelines for structural Engi‐neering ‐ general ‐ part 3 ‐ tests during construction ‐ part 3.3
The above listed standards are to be used in connection with the follow‐ing guidance documents:
ZTV‐Ing, Teil 3 2012‐03
Additional terms of contract and guidelines for structural Engineering ‐ solid structure ‐ part 4 ‐ protection and maintenance of concrete building parts ‐ annex B ‐ determination of concrete hu‐midity with the CM‐device
DAfStB RiLi Schutz und Instandsetzung von Betonbauteilen 2001‐10
DAfStB guideline for protection and maintenance of concrete building parts ‐ part 3: requirements for service companies and surveillance of execu‐tion
DAfStb RiLi Wasserge‐fährdende Stoffe 2011‐11
DAfStb ‐ guideline for concrete structural engineering using wa‐ter‐polluting substances ‐ annex A: test method (only test method A2)
DAfStb Heft 422 1991
Testing of concrete ‐ advice and hints as in addition to DIN 1048, only chapters 2.2, 2.5, 2.6 und 3.3
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 6/52Date of issue: 08.09.2015
The above listed standards are to be used in connection with the follow‐ing guidance document:
DAStb‐Richtline 2010‐03
Steel fibre concrete
DIN 1048‐2 1991‐06
Testing concrete ‐ testing of hardened concrete (specimens taken in situ)
DIN 1048‐4 1991‐06
Test methods for concrete ‐ determination of the compressive strength in hardened concrete in structures and components ‐ application of reference lines and evaluation with special methods
DIN EN 13791 2008‐05
Assessment of in‐situ compressive strength in structures and precast concrete components
DIN EN 14488‐1 2005‐11
Testing sprayed concrete ‐ Part 1: Sampling fresh and hardened concrete
DIN EN 14488‐3 2006‐09
Testing sprayed concrete ‐ Part 3: Flexural strengths (first peak, ultimate and residual) of fibre reinforced beam specimens
DIN EN 14488‐4 2008‐08
Testing sprayed concrete ‐ Part 4: Bond strength of cores by di‐rect tension
DIN EN 14488‐6 2006‐09
Testing sprayed concrete ‐ Part 6: Thickness of concrete on a substrate
DIN EN 14488‐7 2006‐08
Testing sprayed concrete ‐ Part 7: Fibre content of fibre rein‐forced concrete
DIN EN 14845‐1 2007‐09
Test methods for fibres in concrete ‐ Part 1: Reference concretes
DIN EN 14845‐2 2006‐11
Test methods for fibres in concrete ‐ Part 2: Effect on concrete
The above listed standards are to be used in connection with the follow‐ing guidance documents:
DIN EN 14889‐1 2006‐11
Fibres for concrete ‐ Part 1: Steel fibres ‐ Defini‐tions, specifications and conformity
DIN EN 14889‐2 2006‐11
Fibres for concrete ‐ Part 2: Polymer fibres ‐ Definitions, specifications and conformity
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 7/52Date of issue: 08.09.2015
DIN 1100 2004‐05
Hard aggregates for cement‐bound floor screeds ‐ Requirements and test methods
Other applicable documents:
ONR 23303 2010‐03
Test methods for concrete ‐ National application of testing standards for concrete and its source materials
ÖNORM B 4706 2008‐12
Repair, reconstruction and strengthening of concrete structures
1.2 Grout DIN 272 1986‐02
Testing of magnesium oxychloride screeds
DIN EN 1308 2007‐11
Adhesives for tiles ‐ Determination of slip
The above listed standards are to be used in connection with the following guidance document:
DIN EN 1323 2007‐11
Adhesives for tiles ‐ Concrete slabs for tests
DIN EN 1324 2007‐11
Adhesives for tiles ‐ Determination of shear adhesion strength of dispersion adhesives
DIN EN 1346 2007‐11
Adhesives for tiles ‐ Determination of open time
DIN EN 1347 2007‐10
Adhesives for tiles ‐ Determination of wetting capability
DIN EN 1348 2007‐11
Adhesives for tiles ‐ Determination of tensile adhesion strength for cementitious adhesives
DIN EN 1015‐1 2007‐05
Methods of test for mortar for masonry ‐ Part 1: Determination of particle size distribution (by sieve analysis)
DIN EN 1015‐2 2007‐05
Methods of test for mortar for masonry ‐ Part 2: Bulk sampling of mortars and preparation of test mortars
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 8/52Date of issue: 08.09.2015
DIN EN 1015‐3 2007‐05
Methods of test for mortar for masonry ‐ Part 3: Determination of consistence of fresh mortar (by flow table)
DIN EN 1015‐4 1998‐12
Methods of test for mortar for masonry ‐ Part 4: Determination of consistence of fresh mortar (by plunger penetration)
DIN EN 1015‐6 2007‐05
Methods of test for mortar for masonry ‐ Part 6: Determination of bulk density of fresh mortar
DIN EN 1015‐7 1998‐12
Methods of test for mortar for masonry ‐ Part 7: Determination of air content of fresh mortar
DIN EN 1015‐9 2007‐05
Methods of test for mortar for masonry ‐ Part 9: Determination of workable life and correction time of fresh mortar
DIN EN 1015‐10 2007‐05
Methods of test for mortar for masonry ‐ Part 10: Determination of dry bulk density of hardened mortar
DIN EN 1015‐11 2007‐05
Methods of test for mortar for masonry ‐ part 11: determination of flexural and compressive strength of hardened mortar
DIN EN 1015‐12 2000‐06
Methods of test for mortar for masonry ‐ Part 12: Determination of adhesive strength of hardened rendering and plastering mortars on substrates
DIN EN 1015‐18 2003‐03
Methods of test for mortar for masonry ‐ Part 18: Determination of water absorption coefficient due to capillary action of hardened mortar
DIN EN 1015‐19 2005‐01
Methods of test for mortar for masonry ‐ Part 19: Determination of water vapour permeability of hardened rendering and plastering mortars
DIN EN 12002 2009‐01
Adhesives for tiles ‐ Determination of transverse deformation for cementitious adhesives and grouts
DIN EN 12003 2009‐01
Adhesive for tiles ‐ Determination of shear adhesion strength of reaction resin adhesives
The above listed standards are to be used in connection with the following guidance documents:
DIN EN 12004 2012‐09
Adhesives for tiles ‐ Requirements, evaluation of conformity, classification and designation
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 9/52Date of issue: 08.09.2015
DIN EN 12004 2014‐02
Adhesives for tiles ‐ Requirements, evaluation of conformity, classification and designation
DIN 18555‐1 1982‐09
Testing of mortars containing mineral binders ‐ general, sampling, test mortar (withdrawn standard)
DIN 18555‐2 1982‐09
Testing of mortars containing mineral binders ‐ freshly mixed mor‐tars containing aggregates of dense structure (heavy aggregates) ‐ determination of consistence, bulk density and air content (withdrawn standard)
DIN 18555‐3 1982‐09
Testing of mortars containing mineral binders ‐ hardened mortars ‐ determination of flexural strength, compressive strength and bulk density
DIN 18555‐4 1986‐03
Testing of mortars containing mineral binders ‐ hardened mortars ‐ determination of linear and transverse strain and of deformation characteristics of masonry mortars by the static pressure test
DIN 18555‐5 1986‐03
Testing of mortars containing mineral binders ‐ hardened mortars ‐ determination of bond shear strength of masonry mortars (withdrawn standard)
DIN 18555‐6 1987‐11
Testing of mortars containing mineral binders ‐ determination of bond strength of hardened mortar
DIN 18555‐7 1987‐11
Testing of mortars containing mineral binders ‐ determination of water retentivity of freshly mixed mortar by the filter plate method
DIN 18555‐8 1987‐11
Testing of mortars containing mineral binders ‐ freshly mixed mor‐tar ‐ determination of workability time and correction time of thin‐bed mortar for use with masonry (withdrawn standard)
DIN 18555‐9 1999‐09
Testing of mortars containing mineral binders ‐ Part 9: Hardened mortars ‐ determination of the mortar compressive strength in the bed joint
DIN 18556 1985‐01
Testing of coating material for synthetic resin plasters and of syn‐thetic resin plasters (withdrawn standard)
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 10/52Date of issue: 08.09.2015
1.3 Screeds DIN EN 13892‐1 2003‐02
Methods of test for screed materials ‐ Part 1: Sampling, making and curing specimens for test
DIN EN 13892‐2 2003‐02
Methods of test for screed materials ‐ Part 2: Determination of flexural and compressive strength
DIN EN 13892‐3 2004‐07
Methods of test for screed materials ‐ Part 3: Determination of wear resistance‐Böhme
DIN EN 13892‐8 2003‐02
Methods of test for screed materials ‐ Part 8: Determination of bond strength
The above listed standards are to be used in connection with the follow‐ing guidance documents:
DIN EN 13813 2003‐01
Screed material and floor screeds ‐ Screed mate‐rials ‐ Properties and requirements
DIN 18560‐1 2009‐09
Floor screeds in building construction ‐ Part 1: General requirements, testing and construction
DIN 18560‐2 2009‐09
Floor screeds in building construction ‐ Part 2: Floor screeds and heating floor screeds on insula‐tion layers
DIN 18560‐3 2006‐03
Floor screeds in building construction ‐ Part 3: Base‐bonded floor screeds
DIN 18560‐4 2012‐06
Floor screeds ‐ Part 4: Screeds laid on separated layer
DIN 18560‐7 2004‐04
Floor screeds ‐ Part 7: Heavy‐duty screeds (industrial screeds)
1.4 Building bricks and masonry DIN EN 846‐2 2000‐08
Methods of tests for ancillary components for masonry ‐ Part 2: Determination of bond strength of prefabricated bed joint rein‐forcement in mortar joints
DIN EN 846‐3 2000‐08
Methods of tests for ancillary components for masonry ‐ Part 3: Determination of shear load capacity of welds in prefabricated bed joint reinforcement
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 11/52Date of issue: 08.09.2015
DIN EN 846‐4 2005‐01
Methods of test for ancillary components for masonry ‐ Part 4: Determination of load capacity and load‐deflection characteris‐tics of straps
DIN EN 846‐5 2012‐11
Methods of test for ancillary components for masonry ‐ Part 5: Determination of tensile and compressive load capacity and load displacement characteristics of wall ties (couplet test)
DIN EN 846‐6 2012‐11
Methods of test for ancillary components for masonry ‐ Part 6: Determination of tensile and compressive load capacity and load displacement characteristics of wall ties (single end test)
DIN EN 846‐7 2012‐11
Methods of test for ancillary components for masonry ‐ Part 7: Determination of shear load capacity and load displacement characteristics of shear ties and slip ties (couplet test for mortar joint connections)
DIN EN 846‐8 2006‐10
Methods of tests for ancillary components for masonry ‐ Part 8: Determination of load capacity and load‐deflection characteris‐tics of joist hangers
DIN EN 846‐9 2000‐08
Methods of tests for ancillary components for masonry ‐ Part 9: Determination of flexural resistance and shear resistance of lin‐tels
DIN EN 846‐10 2000‐08
Methods of test for ancillary components for masonry ‐ Part 10: Determination of load capacity and load deflection characteristics of brackets
DIN EN 846‐11 2000‐08
Methods of test for ancillary components for masonry ‐ Part 11: Determination of dimensions and bow of lintels
DIN EN 846‐13 2001‐12
Methods of test for ancillary components for masonry ‐ Part 13: Determination of resistance to impact, abrasion and corrosion of organic coatings
DIN EN 772‐1 2011‐07
Methods of test for masonry units ‐ Part 1: Determination of compressive strength
DIN EN 772‐6 2002‐02
Methods of test for masonry units ‐ Part 6: Determination of bending tensile strength of aggregate concrete masonry units
DIN EN 772‐14 2002‐02
Methods of test for masonry units ‐ Part 14: Determination of moisture movement of aggregate concrete and manufactured stone masonry units
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 12/52Date of issue: 08.09.2015
DIN EN 772‐15 2000‐09
Methods of test for masonry units ‐ Part 15: Determination of water vapour permeability of autoclaved aerated concrete ma‐sonry units
The above listed standards are to be used in connection with the follow‐ing guidance documents:
DIN EN 845‐1 2013‐10
Specification for ancillary components for ma‐sonry ‐ Part 1: Wall ties, tension straps, hangers and brackets
DIN EN 845‐2 2013‐08
Specification for ancillary components for ma‐sonry ‐ Part 2: Lintels
DIN EN 845‐3 2013‐08
Specification for ancillary components for masonry ‐ Part 3: Bed joint reinforcement of steel meshwork
DIN V 18151‐100 2005‐10
Lightweight concrete hollow blocks ‐ Part 100: Hollow blocks with specific properties
DIN V 18152‐100 2005‐10
Lightweight concrete solid bricks and blocks ‐ Part 100: Solid bricks and blocks with specific properties
DIN V 18153‐100 2005‐10
Concrete masonry units (Normal‐weight concrete) ‐ Part 100: Masonry units with specific properties
DIN 105‐100 2012‐01
Clay masonry units ‐ Part 100: Clay masonry units with specific properties
1.5 Aerated and lightweight concrete DIN EN 678 1994‐02
Determination of the dry density of autoclaved aerated concrete
DIN EN 679 2005‐09
Determination of the compressive strength of autoclaved aerated concrete
DIN EN 680 2006‐03
Determination of the drying shrinkage of autoclaved aerated concrete
DIN EN 990 2003‐01
Test methods for verification of corrosion protection of reinforcement in autoclaved aerated concrete and lightweight aggregate concrete with open structure
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 13/52Date of issue: 08.09.2015
DIN EN 991 1995‐09
Determination of the dimensions of prefabricated reinforced components made of autoclaved aerated concrete or lightweight aggregate concrete with open structure
DIN EN 992 1995‐09
Determination of the dry density of lightweight aggregate con‐crete with open structure
DIN EN 1351 1997‐02
Determination of flexural strength of autoclaved aerated con‐crete
DIN EN 1352 1997‐02
Determination of static modulus of elasticity under compression of autoclaved aerated concrete or lightweight aggregate concrete with open structure
DIN EN 1353 1997‐02
Determination of moisture content of autoclaved aerated concrete
DIN EN 1354 2005‐09
Determination of compressive strength of lightweight aggregate concrete with open structure
The above listed standards are to be used in connection with the follow‐ing guidance documents:
DIN V 4165‐100 2005‐10
Autoclaved aerated concrete masonry units ‐ Part 100: High precision units and elements with specific properties
DIN 4166 1997‐10
Autoclaved aerated concrete slabs and panels
1.6 physical performance of construction products DIN EN ISO 12571 2013‐12
Hygrothermal performance of building materials and products ‐ Determination of hygroscopic sorption properties
DIN EN ISO 12572 2001‐09
Hygrothermal performance of building materials and products ‐ Determination of water vapour transmission properties
DIN EN 12667 2001‐05
Thermal performance of building materials and products ‐ Determination of thermal resistance by means of guarded hot plate and heat flow meter methods ‐ Products of high and medium thermal resistance
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 14/52Date of issue: 08.09.2015
1.7 Roof panels, insulating materials, wooden structures, planked ceiling and suspended ceilings
DIN EN 492 2012‐12
Fibre‐cement slates and fittings ‐ Product specification and test methods, except 7.3.3, 7.4.2 und 7.5
DIN EN 494 2013‐01
Fibre‐cement profiled sheets and fittings ‐ Product specification and test methods, only 7.3.1 and 7.3.2
DIN EN 822 2013‐05
Thermal insulating products for building applications ‐ Determina‐tion of length and width
DIN EN 823 2013‐05
Thermal insulating products for building applications ‐ Determina‐tion of thickness
DIN EN 824 2013‐05
Thermal insulating products for building applications ‐ Determina‐tion of squareness
DIN EN 825 2013‐05
Thermal insulating products for building applications ‐ Determina‐tion of flatness
DIN EN 826 2013‐05
Thermal insulating products for building applications ‐ Determina‐tion of compression behaviour (here: without determination of 10%‐compression)
DIN EN 1602 2013‐05
Thermal insulating products for building applications ‐ Determina‐tion of the apparent density
DIN EN 1607 2013‐05
Thermal insulating products for building applications ‐ Determina‐tion of tensile strength perpendicular to faces
DIN EN 1608 2013‐05
Thermal insulating products for building applications ‐ Determina‐tion of tensile strength parallel to faces
DIN EN 1609 2013‐05
Thermal insulating products for building applications ‐ Determina‐tion of short term water absorption by partial immersion
DIN EN 12086 2013‐06
Thermal insulating products for building applications ‐ Determina‐tion of water vapour transmission properties
DIN EN 12087 2013‐06
Thermal insulating products for building applications ‐ Determina‐tion of water vapour transmission properties
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 15/52Date of issue: 08.09.2015
DIN EN 12089 2013‐06
Thermal insulating products for building applications ‐ Determina‐tion of bending behaviour
DIN 4158 1978‐05
Filler concrete joists for reinforced and prestressed concrete floors
DIN 1052‐10 2012‐05
Design of timber structures ‐ Part 10: Additional provisions
DIN EN 1382 2000‐03
Timber structures ‐ Test methods ‐ Withdrawel capacity of timber fasteners
DIN EN 1383 2000‐03
Timber structures ‐ Test methods ‐ Pull through resistance of timber fasteners
DIN EN 14592 2012‐07
Timber structures ‐ Dowel‐type fasteners ‐ Requirements
DIN EN 14195 2011‐11
Metal framing components for gypsum board systems ‐ Defini‐tions, requirements and test methods
DIN EN 14316‐1 2004‐11
Thermal insulation products for buildings ‐ In‐situ thermal insula‐tion formed from expanded perlite (EP) products ‐ Part 1: Specifi‐cation for bonded and loose‐fill products before installation
DIN 18168‐2 2008‐05
Ceiling linings and suspended ceilings with gypsum plasterboards ‐ Part 2: Verification of the load‐carrying capacity of metal sub‐constructions and metal suspending rods
in connection with :
DIN 18168‐1 2007‐04
Ceiling linings and suspended ceilings with gypsum plasterboards ‐ Part 1: Requirements for construc‐tion
DIN EN 13964 2014‐08
Suspended ceilings ‐ Requirements and test methods
ETAG 003 1999
Guideline for european technical approval of internal partition kits for use as non‐loadbearing walls
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 16/52Date of issue: 08.09.2015
1.8 Cast stones
DIN V 18500 2006‐12
Cast stones ‐ Terminology, requirements, testing, inspection
in connection with :
DIN 483 2005‐10
Concrete kerb units ‐ Shapes, dimensions, marking
DIN EN 1338 2003‐08 + Corrigenda 1 2006‐11
Concrete paving blocks ‐ Requirements and test methods, not annex G
E DIN EN 1338 2010‐08
Concrete paving blocks ‐ Requirements and test methods, not annex G
Bundesverband Deutsche Beton‐ und Fertigteil‐industrie e.V., Bonn 1996‐04
Guideline, production and quality assurance of permeable con‐crete paving blocks made of open matrix concrete
DIN EN 1339 2003‐08 + Corrigenda 1 2006‐11
Concrete paving flags ‐ Requirements and test methods, not annex G
E DIN EN 1339 2010‐08
Concrete paving flags ‐ Requirements and test methods, not annex G
DIN EN 1340 2003‐08 + Corrigenda 1 2006‐11
Concrete kerb units ‐ Requirements and test methods, not annex G
E DIN EN 1340 2010‐08
Concrete kerb units ‐ Requirements and test methods, not annex G
DIN EN 13748‐1 2005‐08
Terrazzo tiles ‐ Part 1: Terrazzo tiles for internal use, not section 5.6.1
DIN EN 13748‐2 2005‐03
Terrazzo tiles ‐ Part 2: Terrazzo tiles for external use, not section 5.6.1
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 17/52Date of issue: 08.09.2015
The above listed standards are to be used in connection with the follow‐ing guidance document:
BGB‐RINGB 2006‐11
Non standardized concrete products ‐ Require‐ments and test methods
DIN 19555 2003‐04
Step irons for single‐line installation ‐ Step irons for setting in concrete
DIN 19555 Corrigenda 1 2006‐04
Step irons for single‐line installation ‐ Step irons for setting in concrete
DIN EN 13101 2003‐04
Steps for underground man entry chambers ‐ Requirements, marking, testing and evaluation of conformity
DIN EN 1433 2005‐09
Drainage channels for vehicular and pedestrian areas ‐ Classifica‐tion, design and testing requirements, marking and evaluation of conformity
DIN EN 124 1994‐08
Gully tops and manhole tops for vehicular and pedestrian areas ‐ design requirements, testing, marking, quality control
1.9 Mineral construction materials DIN EN 932‐1 1996‐11
Test for general properties of aggregates ‐ Part 1: Methods for sampling
in connection with :
ZTV wwG‐StB By 05 Az: IID9‐43437‐002/92 2005‐21‐12
Additional technical Conditions for contract and delivery for required water management relevant quality parameter for the use of recycled‐ road construction products in Bavaria, only section 6.1
DIN EN 932‐2 1999‐03
Test for general properties of aggregates ‐ Part 2: Methods for reducing laboratory samples
DIN EN 932‐3 2003‐12
Tests for general properties of aggregates ‐ Part 3: Procedure and terminology for simplified petrographic description
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 18/52Date of issue: 08.09.2015
The above listed standards are to be used in connection with the following guidance document:
DIN EN 932‐5 2012‐05
Tests for general properties of aggregates ‐ Part 5: Common equipment and calibration
DIN EN 933‐1 2012‐03
Tests for geometrical properties of aggregates ‐ Part 1: Determina‐tion of particle size distribution ‐ Sieving method
ÖNORM EN 933‐1 2012‐03
Tests for geometrical properties of aggregates ‐ Part 1: Determina‐tion of particle size distribution ‐ Sieving method
ÖNORM EN 13286‐41 2003‐06
Unbound and hydraulically bound mixtures ‐ Part 41: Test method for the determination of the compressive strength of hydraulically bound mixtures
ÖNORM EN 13286‐42 2003‐06
Unbound and hydraulically bound mixtures ‐ Part 42: Test method for the determination of the indirect tensile strength of hydraulically bound mixtures
DIN EN 933‐3 2012‐04
Tests for geometrical properties of aggregates ‐ Part 3: Determina‐tion of particle shape ‐ Flakiness index
DIN EN 933‐4 2015‐01
Tests for geometrical properties of aggregates ‐ Part 4: Determina‐tion of particle shape ‐ Shape index
DIN EN 933‐5 2005‐02
Tests for geometrical properties of aggregates ‐ Part 5: Determina‐tion of percentage of crushed and broken surfaces in coarse aggregate particles
DIN EN 933‐6 2014‐07
Tests for geometrical properties of aggregates ‐ Part 6: Assessment of surface characteristics ‐ Flow coefficient of aggregates
DIN EN 933‐7 1998‐05
Tests for geometrical properties of aggregates ‐ Part 7: Determina‐tion of shell content ‐ percentage of shells in coarse aggregates
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 19/52Date of issue: 08.09.2015
DIN EN 933‐8 2012‐04
Tests for geometrical properties of aggregates ‐ Part 8: Assessment of fines ‐ Sand equivalent test
DIN EN 933‐9 2013‐07
Tests for geometrical properties of aggregates ‐ Part 9: Assessment of fines ‐ Methylene blue test
DIN EN 933‐10 2009‐10
Tests for geometrical properties of aggregates ‐ Part 10: Assessment of fines ‐ Grading of filler aggregates (air jet sieving)
DIN EN 933‐11 2011‐05
Tests for geometrical properties of aggregates ‐ Part 11: Classifica‐tion test for the constituents of coarse recycled aggregate
DIN 52106 2013‐12
Testing of aggregates ‐ Test methods for the assessment of the weathering resistance
DIN EN 1097‐1 2011‐04
Tests for mechanical and physical properties of aggregates ‐ Part 1: Determination of the resistance to wear (micro‐Deval)
DIN EN 1097‐2 2010‐07
Tests for mechanical and physical properties of aggregates ‐ Part 2: Methods for the determination of resistance to fragmentation
DIN EN 1097‐3 1998‐06
Tests for mechanical and physical properties of aggregates ‐ Part 3: Determination of loose bulk density and voids
DIN EN 1097‐4 2008‐06
Tests for mechanical and physical properties of aggregates ‐ Part 4: Determination of the voids of dry compacted filler
DIN EN 1097‐7 2008‐06 + Corrigenda 1 2008‐09
Tests for mechanical and physical properties of aggregates ‐ Part 7: Determination of the particle density of filler ‐ Pyknometer method
DIN EN 1097‐8 2009‐10
Tests for mechanical and physical properties of aggregates ‐ Part 8: Determination of the polished stone value
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 20/52Date of issue: 08.09.2015
DIN EN 1367‐2 2010‐02
Tests for thermal and weathering properties of aggregates ‐ Part 1: Determination of resistance to freezing and thawing
DIN EN 1367‐3 2001‐06 + Corrigenda 1 2004‐09
Tests for thermal and weathering properties of aggregates ‐ Part 3: Boiling test for "Sonnenbrand basalt”
DIN EN 1367‐5 2011‐04
Tests for thermal and weathering properties of aggregates ‐ Part 5: Determination of resistance to thermal shock
DIN EN 1367‐6 2008‐12
Tests for thermal and weathering properties of aggregates ‐ Part 6: Determination of resistance to freezing and thawing in the pres‐ence of salt (NaCl)
DIN EN 13055‐1 2002‐08 + Corrigenda 1 2004‐12
Lightweight aggregates for concrete, mortar, grout, bituminous mixtures, surface treatments and for unbound and bound applica‐tions, not annex B
E DIN EN 13055‐1 2012‐05
Lightweight aggregates for concrete, mortar, grout, bituminous mixtures, surface treatments and for unbound and bound applica‐tions, not annex B
DIN EN 13055‐2 2004‐09
Lightweight aggregates ‐ Part 2: Lightweight aggregates for bitumi‐nous mixtures and surface treatments and for unbound and bound applications
DIN 52115‐2 2014‐02
Test methods for aggregates ‐ Part 2: Impact test on crushed and broken aggregates larger than 32 mm
DIN EN 1744‐1 2013‐03
Tests for chemical properties of aggregates ‐ Part 1: Chemical analysis, only chapter. 14.2 und 15.1
DIN EN 13286‐2 2013‐02
Unbound and hydraulically bound mixtures ‐ Part 2: Test methods for laboratory reference density and water content ‐ Proctor com‐paction
DIN EN 13383‐2 2013‐08
Armourstone ‐ Part 1: Specification
DIN EN 13450 2013‐07
Aggregates for railway ballast, only annexes A, C and D
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 21/52Date of issue: 08.09.2015
DIN EN 13179‐1 2013‐09
Tests for filler aggregate used in bituminous mixtures ‐ Part 1: Delta ring and ball test
TP Beton StB 10 ‐ Teil 3.1 2010
TP concrete‐StB 10 ‐ Technical test specifications for load bearing strata with hydraulic Binders and concrete road surfaces, part 3.1
TP Gestein‐StB Teil 3.1.4 2008
TP aggregates ‐StB: Technische test specification for aggregates for road construction ‐ material labelling of household waste incinera‐tor ash (municipal incinerator bottom ash aggregates)
TP Gestein‐StB Teil 3.1.5 2008
Material labelling of recycled construction materials
TP Gestein‐StB Teil 4.1.3 2008
Determination of grain size distribution of fine grain sizes (air jet sieving)
TP Gestein‐StB Teil 4.1.4 2008
Determination of grain size distribution of Filler (air jet sieving)
TP Gestein‐StB Teil 4.7.1 2008
Estimation of ratio rounded to fragmented parts in fine grain sizes using a Binocular
TP Gestein‐StB Teil 5.3.1.2 2008
Impact test on particle size distributions > 32 mm
TP Gestein‐StB Teil 5.4.1 2015
Los Angeles‐test method on particle size distributions > 32 mm
TP Gestein‐StB Teil 5.4.3 2008
Determination of polished stone value (PSVfGK)
TP Gestein‐StB Teil 5.6 2008
Determination of hardness ‐ Dynamic CBR‐test
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 22/52Date of issue: 08.09.2015
TP Gestein‐StB Teil 6.3.2 2008
Resistance of mineral grain size composition against freeze thaw cycles
TP Gestein‐StB Teil 6.3.3 2008
Resistance of fine aggregates against frost and thaw changes
TP Gestein‐StB Teil 6.5.1 2008
Resistance of coarse aggregates against heat exposure
TP Gestein‐StB Teil 6.5.2 2008
Resistance of fine aggregates against heat exposure
TP Gestein‐StB Teil 6.6.3 2015
Water sensitivity of fine aggregates ‐ shaking and abrasive method
DIN EN 12697‐11 2012‐07
Bituminous mixtures ‐ Test methods for hot mix asphalt ‐ Part 11: Determination of the affinity between aggregate and bitumen
TP Asphalt‐StB Teil 11 2012
Technical test directives for Asphalt ‐ Part 11: adhesion between‐stone and Bitumen
1.10 Natural stone and brick DIN EN 1936 2007‐02
Natural stone test method ‐ Determination of real density and apparent density, and of total and open porosity
DIN EN 13755 2008‐08
Natural stone test methods ‐ Determination of water absorption at atmospheric pressure
DIN 52008 2006‐03
Natural stone test methods ‐ Assessment of the weathering resistance, only annexes C and D
DIN EN 1926 2007‐03
Natural stone test methods ‐ Determination of uniaxial compressive strength
DIN EN 12372 2007‐02
Natural stone test methods ‐ Determination of flexural strength under concentrated load
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 23/52Date of issue: 08.09.2015
DIN EN 13161 2008‐08
Natural stone test methods ‐ Determination of flexural strength under constant moment
DIN EN 13364 2002‐03
Natural stone test methods ‐ Determination of the breaking load at dowel hole
DIN EN 14157 2005‐01
Natural stone test methods ‐ Determination of the abrasion resistance
DIN 51097 1992‐11
Testing of floor coverings ‐ determination of the anti‐slip proper‐ties ‐ wet‐loaded barefoot areas ‐ walking method ‐ ramp test
DIN 51130 2014‐02
Testing of floor coverings ‐ Determination of the anti‐slip property ‐ Workrooms and fields of activities with slip danger ‐ Walking method ‐ Ramp test
DIN EN 538 1994‐11
Clay roofing tiles for discontinuous laying ‐ Flexural strength test
DIN EN 539‐1 2005‐12
Clay roofing tiles for discontinuous laying ‐ Determination of physical characteristics ‐ Part 1: Impermeability test
DIN EN 539‐2 2013‐08
Clay roofing tiles for discontinuous laying ‐ Determination of physical characteristics ‐ Part 2: Test for frost resistance
DIN EN 1024 2012‐06
Clay roofing tiles for discontinuous laying ‐ Determination of geometric characteristics
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 24/52Date of issue: 08.09.2015
2 Geotechnical site investigation, sampling and testing of soil, rocks and aggregate samples
2.1 Sampling DIN EN ISO 14688‐1 2013‐12
Geotechnical investigation and testing ‐ Identification and classification of soil ‐ Part 1: Identification and description
DIN EN ISO 14688‐2 2013‐12
Geotechnical investigation and testing ‐ Identification and classification of soil ‐ Part 2: Principles for a classification
DIN EN ISO 14689‐1 2011‐06
Geotechnical investigation and testing ‐ Identification and classification of rock ‐ Part 1: Identification and description
DIN EN ISO 22475‐1 2007‐01
Geotechnical investigation and testing ‐ Sampling methods and groundwater measurements ‐ Part 1: Technical principles for execution
DIN 4023 2011‐01
Geotechnical investigation and testing ‐ Graphical presentation of logs of boreholes, trial pits, shafts and adits
DIN 19672, Blatt 1 1968‐04
Apparatus for drawing soil samples in agricultural engineering ‐ apparatus for soil sampling in undisturbed situation
DIN 52101 2013‐10
Aggregates test methods ‐ Sampling
2.2 soil and ground physical investigation DIN EN ISO 22476‐2 2012‐03
Geotechnical investigation and testing ‐ Field testing ‐ Part 2: Dynamic probing
FGSV‐Nr. 591/B 15.1 2012
TP BF‐StB ‐ Technical test guidelines for soil and rock in road construction ‐ part B 15.1 – Light dynamic probing DPL‐5 und middle heavy dynamic probing DPM‐10
DIN 4094‐4 2002‐01
Construction site – tests in situ ‐ Part 4: vane shear test
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 25/52Date of issue: 08.09.2015
TP BF‐StB Teil B 8.3 2003
Dynamic plate load test using a Drop‐Weight Tester
DIN 18035‐4 2012‐01
Sports grounds ‐ Part 4: Sports turf areas
DIN 18124 2011‐04
Soil, investigation and testing ‐ Determination of density of solid particles ‐ Capillary pycnometer, wide mouth pycnometer, gas pycnometer
DIN 18126 1996‐11
Soil, investigation and testing ‐ Determination of density of non‐cohesive soils for maximum and minimum compactness
DIN 18130‐2 2011‐07
Soil, investigation and testing ‐ Determination of the coefficient of water permeability ‐ Part 2: Field tests
DIN 18137‐1 2010‐07
Soil, investigation and testing ‐ Determination of shear strenght ‐ Part 1: Concepts and general testing conditions
DGGT‐Empfehlung Nr. 1 2004
Uniaxiale load tests on rock samples
DGGT‐Empfehlung Nr. 2 1986
Triaxiale load tests on rock samples
DGGT‐Empfehlung Nr. 5 1986
Point load tests on rock samples
DGGT‐Empfehlung Nr. 10 1986
Indirect tensile test on rock samples ‐ tension fatigue test
DGGT‐Empfehlung Nr. 11 1986
Swelling pressure test on rock samples
DGGT‐Empfehlung Nr. 12 1987
Multistep technic for triaxial load tests and direct tensile tests
DGGT‐Empfehlung Nr. 16 1994
Uni‐ and triaxial creep tests on rock samples
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 26/52Date of issue: 08.09.2015
QMA 4.3‐05.5‐303 2013‐10
Swelling pressure tests
in connection with :
DGGT‐Empfehlung Nr. 111986
Swelling pressure test on rock samples
DIN EN 932‐3 2003‐12
Tests for general properties of aggregates ‐ Part 3: Procedure and terminology for simplified petrographic description
2.3 Test methods (investigation area I) by third party testing authorities for the installa‐tion of mineral construction materials in landfill liner systems according to the Land‐fill Ordinance ‐ DepV and Federal Uniform Quality Standard BQS 9‐1
DIN 18121‐1 1998‐04
Soil, investigation and testing ‐ Water content ‐ Part 1: Determina‐tion by drying in oven
DIN 18121‐2 2012‐02
Soil, investigation and testing ‐ Water content ‐ Part 2: Determina‐tion by rapid methods
DIN 18122‐1 1997‐07
Soil, investigation and testing ‐ Consistency limits ‐ Part 1: Deter‐mination of liquid limit and plastic limit
DIN 18123 2011‐04
Soil, investigation and testing ‐ Determination of grain‐size distri‐bution
DIN 18125‐1 2010‐07
Soil, investigation and testing ‐ Determination of density of soil ‐ Part 1: Laboratory tests
DIN 18125‐2 1999‐08/2011‐03*
Soil investigation and testing ‐ Determination of density of soil ‐ Part 2: Field tests (Edition 1999‐11 ‐ replaced)
DIN 18127 1997‐11/2012‐09*
Soil, investigation and testing ‐ Proctor‐test (Edition 1997‐11 ‐ replaced)
DIN 18128 1990‐11/2002‐12*
Soil ‐ Investigation and testing ‐ Determination of ignition loss (Edition 1990‐11 ‐ replaced)
DIN 18129 1996‐11/2010‐10/ 2011‐07*
Soil, investigation and testing ‐ Determination of lime content (Edition 1996‐11 und 2010‐10 ‐ replaced)
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 27/52Date of issue: 08.09.2015
DIN 18130‐1 1998‐05
Soil ‐ investigation and testing ‐ Determination of the coefficient of water permeability ‐ Part 1: Laboratory tests
DIN 18132 1995‐12/2012‐04*
Soil, testing procedures and testing equipment ‐ Determination of water absorption (Edition 1995‐12 ‐ replaced)
DIN 18134 2012‐04*
Soil ‐ Testing procedures and testing equipment ‐ Plate load test (Edition 2001‐09 and 2010‐04 ‐ replaced)
DIN 19682‐1 2007‐11
Soil quality ‐ Field tests ‐ Part 1: Determination of soil colour
DIN 19682‐2 2007‐11/2013‐08/ 2014‐07*
Soil quality ‐ Field tests ‐ Part 2: Determination of soil texture(Edition 2007‐11 und 2013‐08 ‐ replaced)
GDA E 3‐12 (Nr. 3.6):2011 GDA‐Empfehlungen 3. Auflage 1997 S.268 Überarbeitung 4/2011
Acceptance test of mineral drainage layers para. 3.6 ‐ total carbonate content
2.4 Test methods (Investigation area II) by third party testing authorities for the installa‐tion mineral construction materials in landfill liner systems according to the Landfill Ordinance ‐ DepV and Federal Uniform Quality Standard BQS 9‐1
DIN EN 932‐1 1996‐11
Test for general properties of aggregates ‐ Part 1: Methods for sampling
DIN EN 932‐2 1999‐03
Test for general properties of aggregates ‐ Part 2: Methods for reducing laboratory samples
DIN EN 1097‐5 2008‐06 + Corrigenda 1 2008‐09
Tests for mechanical and physical properties of aggregates ‐ Part 5: Determination of the water content by drying in a venti‐lated oven
DIN EN 1097‐6 2005‐12/2013‐09
Tests for mechanical and physical properties of aggregates ‐ Part 6: Determination of particle density and water absorption (Edition 2005‐12 ‐ replaced)
DIN EN 1367‐1 2007‐06
Tests for thermal and weathering properties of aggregates ‐ Part 1: Determination of resistance to freezing and thawing
DIN 18122‐2 2000‐09
Soil ‐ investigation and testing ‐ Part 2: Determination of the shrinkage limit
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 28/52Date of issue: 08.09.2015
DIN 18135 2011‐04/2012‐04
Investigation and testing ‐ Oedometer consolidation test (Edition 2011‐04 ‐ replaced)
DIN 18136 2003‐11
Soil ‐ Investigation and testing ‐ Unconfined compression test
DIN 18137‐2 1990‐12/2011‐04*
Soil, investigation and testing ‐ Determination of shear strength ‐ Part 2: Triaxial test (Edition 1990‐12 ‐ replaced)
DIN 18137‐3 2002‐09
Soil, investigation and testing ‐ Determination of shear strength ‐ Part 3: Direct shear test
DIN 4094‐2 1990‐12/2003‐05
Construction site ‐ tests in situ ‐ part 2: Standard Penetration Test (Edition 1990‐12 ‐ replaced)
Other applicable documents (for Investigation areas I and II) DIN EN 12620 2008‐07
Aggregates for concrete
DIN 18196 2006‐06/2011‐05*
Earthworks and foundation ‐ soil classification for civil engineering purposes (Edition 2006‐06 ‐ replaced)
*Previous editions already replaced new versions, but still remain as basis of BQS
2.5 Testing of bituminous construction materials DIN EN 12697‐20 2012‐06
Bituminous mixtures ‐ Test methods for hot mix asphalt ‐ Part 20: Indentation using cube or cylindrical specimens
TP Asphalt‐StB Teil 20 2007
Technical testing of asphalt ‐ Part 20: Intrusion depth on cubic samples
DIN EN 12697‐27 2001‐04
Bituminous mixtures ‐ Test methods for hot mix asphalt ‐ Part 27: sampling
TP Asphalt‐StB Teil 27 2012
Technical guidelines for bituminous mixtures ‐ Part 27: sampling
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 29/52Date of issue: 08.09.2015
DIN EN 12697‐28 2001‐04
Bituminous mixtures ‐ Test methods for hot mix asphalt ‐ Part 28: Preparation of samples for determining binder content, water content and grading
TP Asphalt‐StB Teil 28 2007
Technical test guidelines for bituminous mixtures ‐ Part 28: Preparation of samples
DIN EN 12697‐30 2012‐06
Bituminous mixtures ‐ Test methods for hot mix asphalt ‐ Part 30: Specimen preparation by impact compactor
TP Asphalt‐StB Teil 30 2007
Technical test guidelines for bituminous mixtures ‐ Part 30: mak‐ing of test specimens with the impact compactor (MVG)
DIN EN 12697‐1 2012‐09
Bituminous mixtures ‐ Test methods for hot mix asphalt ‐ Part 1: Soluble binder content
TP Asphalt‐StB Teil 1 2012
Technical test guidelines for bituminous mixtures ‐ Part 1: Soluble binder content
DIN EN 12697‐3 2013‐08
Bituminous mixtures ‐ Test methods for hot mix asphalt ‐ Part 3: Bitumen recovery: Rotary evaporator
TP Asphalt‐StB Teil 3 2007
Technical test guidelines for bituminous mixtures ‐ Part 3: Bitu‐men recovery: Rotary evaporator
DIN EN 12697‐5 2010‐04
Technical test guidelines for bituminous mixtures Part 5: Deter‐mination of the maximum density
TP Asphalt‐StB Teil 5 2012
Technical test guidelines for bituminous mixtures ‐Part 5: Deter‐mination of the maximum density
DIN EN 12697‐6 2012‐07
Bituminous mixtures ‐ Test methods for hot mix asphalt ‐ Part 6: Determination of bulk density of bituminous specimens
TP Asphalt‐StB Teil 6 2012
Technical test guidelines for bituminous mixtures ‐Part 6: Deter‐mination of bulk density of bituminous specimens
DIN EN 12697‐8 2003‐06
Bituminous mixtures ‐ Test methods for hot mix asphalt ‐ Part 8: Determination of the air voids content of bituminous specimen
TP Asphalt‐StB Teil 8 2012
Technical test guidelines for bituminous mixtures ‐ Part 8: Deter‐mination of the air voids content of bituminous specimen and degree of compaction
DIN EN 12697‐2 2007‐11
Bituminous mixtures ‐ Test method for hot mix asphalt ‐ Part 2: Determination of particle size distribution
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 30/52Date of issue: 08.09.2015
TP Asphalt‐StB Teil 2 2010
Technical test guidelines for bituminous mixtures ‐ Part 2: Deter‐mination of particle size distribution
DIN EN 12697‐35 2007‐10
Bituminous mixtures ‐ Test methods for hot mix asphalt ‐ Part 35: Laboratory mixing
TP Asphalt‐StB Teil 35 2007
Technical test guidelines for bituminous mixtures ‐ Part 35: Labo‐ratory mixing
DIN EN 12697‐13 2001‐04
Bituminous mixtures ‐ Test methods for hot mix asphalt ‐ Part 13: Temperature measurement
TP Asphalt‐StB Teil 13 2007
Technical test guidelines for bituminous mixtures – Part 13: Tem‐perature measurement
DIN EN 12697‐18 2004‐10
Bituminous mixtures ‐ Test methods for hot mix asphalt ‐ Part 18: Binder drainage
TP Asphalt‐StB Teil 18 2007
Technical test guidelines for bituminous mixtures ‐ Part 18: Drain of stone mastic asphalt and porous asphalt
DIN EN 12697‐29 2002‐12
Bituminous mixtures ‐ Test method for hot mix asphalt ‐ Part 29: Determination of the dimensions of bituminous specimen
TP Asphalt‐StB Teil 29 2007
Technical test guidelines for bituminous mixtures ‐ Part 29: De‐termination of dimensions of bituminous specimen
TP Asphalt‐StB Teil 80 2012
Technical test guidelines for bituminous mixtures ‐ Part 80: Shear test
ÖNORM B 3639‐1 1997‐07
Asphalts for road construction and related purposes ‐ Testing ‐ Shear resistance in contact surfaces of asphalt layers
ÖNORM B 3639‐2 1997‐07
Asphalts for road construction and related purposes ‐ Testing ‐ Pull‐off‐resistance in contact surfaces of asphalt layers
ÖNORM EN 12697‐36 1997‐07
Bituminous mixtures ‐ Test methods for hot mix asphalt ‐ Part 36: Determination of the thickness of a bituminous pavement
DIN EN 1425 2012‐07
Bitumen and bituminous binders ‐ Characterisation of perceptible properties
DIN EN 1426 2007‐06
Bitumen and bituminous binders ‐ Determination of needle pene‐tration
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 31/52Date of issue: 08.09.2015
E DIN EN 1426 2013‐09
Bitumen and bituminous binders ‐ Determination of needle pene‐tration
DIN EN 1427 2007‐06
Bitumen and bituminous binders ‐ Determination of the softening point ‐ Ring and Ball method
E DIN EN 1427 2013‐09
Bitumen and bituminous binders ‐ Determination of the softening point ‐ Ring and Ball method
DIN EN 13398 2010‐10
Bitumen and bituminous binders ‐ Determination of the elastic recovery of modified bitumen
DIN 52013 2007‐06
Bitumen and bituminous binders ‐ Determination of ductility
DIN EN 12594 2007‐06
Bitumen and bituminous binders ‐ Preparation of test samples
DIN EN 12594 2015‐01
Bitumen and bituminous binders ‐ Preparation of test samples
DIN EN 12607‐1 2013‐12
Bitumen and bituminous binders ‐ Determination of the resis‐tance to hardening under the influence of heat and air ‐ Part 1: RTFOT method
DIN EN 14769 2012‐08
Bitumen and bituminous binders ‐ Accelerated long‐term ageing conditioning by a Pressure Ageing Vessel (PAV)
DIN EN 14770 2012‐08
Bitumen and bituminous binders ‐ Determination of complex shear modulus and phase angle using a Dynamic Shear Rheome‐ter (DSR)
DIN EN 14771 2012‐08
Bitumen and bituminous binders ‐ Determination of the flexural creep stiffness ‐ Bending Beam Rheometer (BBR)
Multiple tress Creep and Recovery Test ‐ AL MSCR‐Prüfung (DSR) 2012
Guideline fort the determination of deformation of Bitumen and bituminous binders using a Dynamic Shear Rheometer (DSR) ‐ execution of MSCR‐test
2.6 Testing of road marking materials DIN EN 12802 2011‐12
Road marking materials ‐ Laboratory methods for identification
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 32/52Date of issue: 08.09.2015
DIN EN 1436 2009‐01
Road marking materials ‐ Road marking performance for road users
DIN EN 1423 2013‐03
Road marking materials ‐ Drop on materials ‐ Glass beads, anti‐skid aggregates and mixtures of the two
DIN EN 1424 2003‐08
Road marking materials ‐ Premix glass beads
ZTV‐M 02 Teil 6.2.1 2002
Testing of height overhang , milling depth, milling width and milling length Examination of the amount supernatant
ZTV‐M 02 Teil 6.2.2 2002
Testing of drop on materials
ZTV‐M 02 Teil 6.2.3 2002
Testing of trafficability (drying time)
ZTV‐M 02 Teil 6.2.4 2002
Testing of day visibility
ZTV‐M 02 Teil 6.2.5 2002
Testing of night visibility
ZTV‐M 02 Teil 6.2.6 2002
Testing of skid resistance
ZTV‐M 02 Teil 6.2.7 2002
Testing of wear resistance (life time)
2.7 Testing of road equipment DIN EN 40‐3‐1 2013‐06
Lighting columns ‐ Part 3‐1: Design and verification ‐ Specifica‐tion for characteristic loads
EN 40‐3‐1 2013‐02
Lighting columns ‐ Part 3‐1: Design and verification ‐ Specifica‐tion for characteristic loads
DIN EN 40‐3‐2 2013‐06
Lighting columns ‐ Part 3‐2: Design and verification ‐ Verification by testing
EN 40‐3‐2 2013‐02
Lighting columns ‐ Part 3‐2: Design and verification ‐ Verification by testing
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 33/52Date of issue: 08.09.2015
DIN EN 40‐3‐3 2013‐06
Lighting columns ‐ Part 3‐3: Design and verification ‐ Verification by calculation
EN 40‐3‐3 2013‐02
Lighting columns ‐ Part 3‐3: Design and verification ‐ Verification by calculation
2.8 Measuring the grip of surfaces DIN EN 13036‐4 2011‐12
Road and airfield surface characteristics ‐ Test methods ‐ Part 4: Method for measurement of slip/skid resistance of a surface ‐ The pendulum test
ARS 17/05 2005‐07
General circular Straßenbau No. 17/2005 ‐ Technical test guide‐lines for measurement of slip/skid resistance in road construc‐tion ‐ Part: Measuring method SRT (TP grip‐StB (SRT))
TP Griff‐StB 2004‐01
Technical test guidelines for measurement of slip/skid resistance in road construction ‐ Part: measuring method SRT (TP Griff‐StB (SRT))
2.9 Messung der Ebenheit von Oberflächen TP Eben ‐ Berührende Messungen 2007
Technical test guidelines for measurement of eveness on road surfaces in the longitudinal and transverse direction ‐ Part: Contact measurements
DIN EN 13036‐6 2008‐06
Road and airfield surface characteristics ‐ Test methods ‐ Part 6: Measurement of transverse and longitudinal profiles in the even‐ness and megatexture wavelength ranges
Applicable documents for monitoring and evaluation of road conditions and surfaces:
FGSV‐Nr. 490‐AP 9 2001/2003/2005/2008
Working documents for maintaining road condi‐tions
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 34/52Date of issue: 08.09.2015
FGSV‐Nr. 490‐AP 9 2001/2003/2005/2008
Working documents for monitoring of road con‐ditions and‐evaluation (ZEB): Reihe M: measuring condition (edition 2001) Reihe V: Visual condition monitoring (edition 2001) Reihe A: Evaluation (edition 2001) Working documents for conserva‐tion/maintenance planning: Reihe R: computer aided conservation planning for rail track anchors (edition 2001) Reihe S: Substance values (stock) (edition 2003) Reihe K: communal requirements clause K 1:Principles
Unterabschnitt K 1.1: Principles for practical implementation of E EMI 2003 (2005) Unterabschnitt K 1.2: Order system and net description for local traffic surfaces (2005) Unterabschnitt K 1.3: data compilation (2008)
Unterabschnitt K 1.4: data organisation of his‐torigraphy (2008) Abschnitt K 2: recording of current status Unterabschnitt K 2.2: preparation and perform‐ance of visual inspection of local traffic surfaces (2005) Unterabschnitt K 2.3: damage catalogue for measuring and visual monitoring of current status (2005)
ZTV ZEB‐StB FGSV‐Nr. 998 2006
Additional technical contractual requirements and guidelines for status recording and evalua‐tion of roads
E EMI FGSV Regelwerk R 2 2012
Recommendations for conservation management of local roads
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 35/52Date of issue: 08.09.2015
3 Mechanical structural test methods, testing of reinforcing steel as well as weld seams of metallic materials, dynamic testing of materials and structural components, corrosion and metallographic investigations
3.1 Tensile tests DIN EN ISO 4136 2013‐02
Destructive tests on welds in metallic materials ‐ Transverse tensile test
DIN EN ISO 5178 2011‐05
Destructive tests on welds in metallic materials ‐ Longitudinal ten‐sile test on weld metal in fusion welded joints
DIN EN ISO 6892‐1 2009‐12
Metallic materials ‐ Tensile testing ‐ Part 1: Method of test at room temperature (methode B)
DIN EN 1561 2012‐01
Founding ‐ Grey cast irons
DIN EN 10002‐1 2009‐12
Metallic materials ‐ Tensile testing ‐ Part 1: Method of test at room temperature (methode B) (withdrawn standard)
in connection with :
DIN EN 10164 2005‐03
Steel products with improved deformation proper‐ties perpendicular to the surface of the product ‐ Technical delivery conditions
DIN EN 12385‐1 2009‐01
Steel wire ropes ‐ Safety ‐ Part 1: General requirements
DIN EN ISO 14273 2002‐03
Specimen dimensions and procedure for shear testing resistance spot, seam and embossed projection welds
E DIN EN ISO 14273 2014‐07
Specimen dimensions and procedure for shear testing resistance spot, seam and embossed projection welds
The above listed standards are to be used in connection with the following guidance documents:
DIN EN 895 1999‐05
Destructive tests on welds in metallic materials ‐ Transverse tensile test
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 36/52Date of issue: 08.09.2015
DIN 50125 2004‐01
Testing of metallic materials ‐ Tensile test pieces
3.2 Impact and bending tests DIN EN ISO 148‐1 2011‐01
Metallic materials ‐ Charpy pendulum impact test ‐ Part 1: Test method
DIN EN ISO 5173 2012‐02
Destructive tests on welds in metallic materials ‐ Bend tests
DIN EN ISO 7438 2012‐03
Metallic materials ‐ Bend test
DIN EN ISO 8491 2004‐10
Metallic materials ‐ Tube (in full section) ‐ Bend test
DIN EN ISO 8492 2004‐10
Metallic materials ‐ Tube ‐ Flattening test
E DIN EN ISO 8492 2013‐06
Metallic materials ‐ Tube ‐ Flattening test
DIN EN ISO 8493 2004‐10
Metallic materials ‐ Tube ‐ Drift‐expanding test
DIN EN ISO 8494 2004‐10
Metallic materials ‐ Tube ‐ Flanging test
DIN EN ISO 8494 2014‐03
Metallic materials ‐ Tube ‐ Flanging test
DIN EN ISO 8495 2004‐10
Metallic materials ‐ Tube ‐ Ring‐expanding test
DIN EN ISO 8495 2014‐03
Metallic materials ‐ Tube ‐ Ring‐expanding test
DIN EN ISO 8496 2004‐10
Metallic materials ‐ Tube ‐ Ring tensile test
DIN EN ISO 8496 2014‐03
Metallic materials ‐ Tube ‐ Ring tensile test
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 37/52Date of issue: 08.09.2015
DIN EN ISO 9016 2013‐02
Destructive tests on welds in metallic materials ‐ Impact tests ‐ Test specimen location, notch orientation and examination
DIN EN 10255 2007‐07
Non‐Alloy steel tubes suitable for welding and threading ‐ Technical delivery conditions
E DIN EN 10255 2010‐11
Non‐Alloy steel tubes suitable for welding, threading and other joining methods ‐ Requirements and test methods
DIN 50115 1991‐04
Testing of Metallic Materials ‐ Notched Bar Impact Bending Test Special samples and evaluation form (withdrawn standard)
DIN 50116 1982‐07
Testing of zinc and zinc alloys ‐ impact test
The above listed standards are to be used in connection with the following guidance documents:
DIN EN 875 1995‐10
Destructive tests on welds in metallic materials ‐ Impact tests ‐ Test specimen location, notch orien‐tation and examination (withdrawn standard)
DIN EN ISO 9016 2011‐05
Destructive tests on welds in metallic materials ‐ Impact tests ‐ Test specimen location, notch orien‐tation and examination
DIN EN 910 1996‐05
Destructive test on welds in metallic materials ‐ Bend tests (withdrawn standard)
DIN EN ISO 5173 2010‐08
Destructive tests on welds in metallic materials ‐ Bend tests
3.3 Hardness tests DIN EN ISO 6506‐1 2006‐03
Metallic materials ‐ Brinell hardness test ‐ Part 1: Test method
DIN EN ISO 6506‐1 2015‐02
Metallic materials ‐ Brinell hardness test ‐ Part 1: Test method
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 38/52Date of issue: 08.09.2015
DIN EN ISO 6507‐1 2006‐03
Metallic materials ‐ Vickers hardness test ‐ Part 1: Test method
DIN EN ISO 6508‐1 2006‐03
Metallic materials ‐ Rockwell hardness test ‐ Part 1: Test method Test methods (hardness scales A, B, C, D, E, F, G, H, K, N, T) (here: HRC)
E DIN EN ISO 6508‐1 2013‐04
Metallic materials ‐ Rockwell hardness test ‐ Part 1: Test method Test methods
The above listed standards are to be used in connection with the following
guidance documents:
DIN EN 1043‐1 1996‐02
Hardness testing ‐ Destructive tests on welds in metallic materials ‐ Part 1 ‐ Hardness test on arc welded joints ‐ (withdrawn standard)
DIN EN 1043‐2 2002‐04
Hardness test ‐ Destructive tests on welds in metallic materials ‐ Part 2: Micro hardness testing on welded joints (withdrawn standard)
DIN EN ISO 14271 2012‐11
Resistance welding ‐ Vickers hardness testing (low‐force and microhardness) of resistance spot, pro‐jection and seam welds
DIN EN ISO 9015‐1 2011‐05
Destructive tests on welds in metallic materials ‐ Hardness testing ‐ Part 1: Hardness test on arc welded joints
DIN EN ISO 9015‐2 2011‐05
Destructive tests on welds in metallic materials ‐ Hardness testing ‐ Part 2: Microhardness testing of welded joints
DIN EN 10328 2005‐04
Iron and steel ‐ Determination of the conventional depth of hard‐ening after surface heating
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 39/52Date of issue: 08.09.2015
3.4 Non‐destructive testing of materials 3.4.1 Visual inspection DIN EN 17635 2011‐05
Non‐destructive testing of welds ‐ General rules for metallic mate‐rials
DIN EN 17637 2011‐05
Non‐destructive testing of welds ‐ Visual testing of fusion‐welded joints
3.4.2 Deformation measurement VdTÜV ‐Merkblatt 803 2008‐10
Guidelines for the implementation and evaluation of strain meas‐urements with stretch marks
The above listed standards are to be used in connection with the following guidance documents:
VDI/VDE/GESA 2635 Blatt 1 2007‐04
Experimental structure analysis ‐ Metallic bonded resistance strain gages ‐ Characteristics and testing conditions
AD 2000‐Merkblatt S4 2000‐10
Review of tensions in computational and experi‐mental tension analysis
3.5 Testing of reinforcing steel DIN 488‐2 2009‐08
Reinforcing steel ‐ reinforcing steel bars
DIN 488‐3 2009‐08
Reinforcing steels ‐ Reinforcing steel in coils, steel wire
DIN 488‐4 2009‐08
Reinforcing steels ‐ Welded fabric
DIN 488‐5 2009‐08
Reinforcing steels ‐ Lattice girders
DIN EN 10080 2005‐08
Steel for the reinforcement of concrete ‐ Weldable reinforcing steel ‐ General
DIN EN ISO 15630‐1 2011‐02
Steel for the reinforcement and prestressing of concrete ‐ Test methods ‐ Part 1: Reinforcing bars, wire rod and wire
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 40/52Date of issue: 08.09.2015
DIN EN ISO 15630‐2 2011‐02
Steel for the reinforcement and prestressing of concrete ‐ Test methods ‐ Part 2: Welded fabric
DIN EN ISO 17660‐1 2006‐12
Welding ‐Welding of reinforcing steel ‐ Part 1: Load‐bearing weldedjoints
DIN EN ISO 17660‐2 2006‐12
Welding ‐Welding of reinforcing steel ‐ Part 2: Non load‐bearing welded joints
3.6 Dynamic testing of materials and structural components DIN 4550 2004‐12
Office furniture ‐ Self‐supporting energized devices for the height adjustment of office work chairs ‐ Safety requirements, testing
DIN 50100 1978‐02
Testing of Materials ‐ Continuous Vibration Test ‐ Definitions, Symbols, Procedure, Evaluation
3.7 Other tests conducted within inspection programmes DIN EN 1057 2010‐06
Copper and copper alloys ‐ Seamless, round copper tubes for water and gas in sanitary and heating applications
DVGW GW 6 1996‐01
Capillary soldered fittings made of red brass and reducer fittings made of copper and red brass ‐ specifications and test requirements
DVGW GW 7 2002‐09
Brazing solder and flux for brazing of copper pipes for gas and water installations
DVGW GW 8 1996‐01
Capillary soldered fittings made of copper pipes ‐ specifications and test requirements
DVGW GW 392 2009‐07
Seamless drawn pipes made of copper for gas and water installa‐tions and internal galvanized pipes made of copper for gas and water installations ‐ Requirements and tests
DVGW VP 614 2013‐12
Permanent tube connections for metal gas pipes ‐ Press connect‐or
DVGW VP 652 2006‐05
Copper wire with firmly adhering plastic sheath for the drinking water installation
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 41/52Date of issue: 08.09.2015
DVGW‐VP 617 1998‐07
Seamless drwan, internal galvanized pipes made of copper for water installations ‐ Requirements and testing assessments (only inspection)
DVGW‐W 534 2004‐05
Connectors for pipes and pipe connections for drinking water installation ‐ process sheet ‐
RAL‐RG 641/1 2009‐08
Quality and testing assesments (loads of performance) for the quality mark “Kupferrohr/RAL) of the Gütegemeinschaft Kupfer‐rohr e.V
RAL‐RG 641/2 2002‐10
Quality and testing assesments (loads of performance) for brazing solder and brazing flux in extension for the quality mark “Kupfer‐rohr/RAL) of the Gütegemeinschaft Kupferrohr e.V.
RAL‐RG 641/3 2000‐01
Quality and testing assesments (loads of performance) for soft solder and solder flux in extension for the quality mark “Kupfer‐rohr/RAL e.V.
RAL‐RG 641/4 2001‐04
Quality assurance of copper pipes Extension to capillary soldered fittings made of copper pipes ‐ Quality and testing assesments
SN 505262 2013‐01
Concrete construction (Testing of concrete steel)
SIA 262 2013‐01
Civil engineering (Testing of concrete steel)
3.8 Metalls and corrosion DIN EN ISO 945‐1 2010‐09
Microstructure of cast irons ‐ Part 1: Graphite classification by visual analysis
DIN EN ISO 1460 1995‐01
Metallic coatings ‐ Hot dip galvanized coatings on ferrous materi‐als ‐ Gravimetric determination of the mass per unit area
DN EN ISO 1461 2009‐10
Hot dip galvanized coatings on fabricazed iron and steels articles ‐ Specifications and test methods
DIN EN ISO 1463 2004‐08
Metallic and oxide coatings ‐ Measurement of coating thickness ‐ Microscopical method
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 42/52Date of issue: 08.09.2015
DIN EN ISO 2178 1995‐04
Non‐magnetic coatings on magnetic substrates ‐ Measurement of coating thickness ‐ Magnetic method
DIN EN ISO 2360 2004‐04
Non‐conductive coatings on non‐magnetic electrically conductive basis materials ‐ Measurement of coating thickness ‐ Amplitude‐sensitive eddy current method
DIN EN ISO 3651‐1 1998‐08
Determination of resistance to intergranular corrosion of stainless steels ‐ Part 1: Austenitic and ferritic‐austenitic (duplex) stainless steels ‐ Corrosion test in nitric acid medium by meas‐urement of loss in mass (Huey test)
DIN EN ISO 3651‐2 1998‐08
Determination of resistance to intergranular corrosion of stainless steels ‐ Part 2: Ferritic, austenitic and ferritic‐austenitic (duplex) stainless steels ‐ Corrosion test in media containing sul‐furic acid
DIN EN ISO 6509 1995‐05
Corrosion of metals and alloys ‐ Determination of dezincification resistance of copper alloys with zinc
DIN EN ISO 6509 2014‐09
Corrosion of metals and alloys ‐ Determination of dezincification resistance of copper alloys with zinc
DIN EN ISO 7539‐1 2013‐04
Corrosion of metals and alloys ‐ Stress corrosion testing ‐ Part 1: General guidance on testing procedures
DIN EN ISO 2639 2003‐04
Steels ‐ Determination and verification of the depth of carburized and hardened cases
ISO 4967 2013‐07
Steel ‐ Determination of content of non‐metallic inclusions ‐ Micrographic method using standard diagrams
DIN EN 10328 2005‐04
Iron and steel ‐ Determination of the conventional depth of hard‐ening after surface heating
DIN 50190‐3 1979‐03
Hardness depth of heat‐treated parts ‐ determination of the effective depth of hardening after nitriding
DIN 50190‐4 1999‐09
Hardness depth of heat‐treated parts ‐ Part 4: Determination of the fusion hardening depth and the fusion depth
DIN EN ISO 3887 2003‐10
Steels ‐ Determination of depth of decarburization
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 43/52Date of issue: 08.09.2015
DIN EN ISO 643 2013‐05
Steels ‐ Micrographic determination of the apparent grain size
DIN EN 10247 2007‐07
Micrographic examination of the non‐metallic inclusion content of steels using standard pictures
DIN 50600 1980‐03
Micrographic examination of the non‐metallic inclusion content of steels using standard pictures
DIN 50905‐2 1987‐01
Corrosion of metals ‐ corrosion testing ‐ corrosion characteristics under uniform corrosion attack
DIN 50905‐3 1987‐01
Corrosion of metals ‐ corrosion testing ‐ corrosion characteristics under nonuniform and localized corrosion attack without me‐chanical stress
DIN 50905‐4 1987‐01
Corrosion of metals ‐ corrosion testing ‐ corrosion testing in liq‐uids under laboratory conditions without mechanical stress
DIN 50915 1993‐09
Testing the resistance of unalloyed and low alloy steels to inter‐granular stress corrosion cracking by attack of nitrate medium ‐ welded and unwelded materials
DIN 50916‐1 1976‐08
Testing of copper alloys ‐ stress corrosion cracking test in ammo‐nia, testing of tubes, rods and profiles
DIN 50916‐2 1985‐09
Testing of copper alloys ‐ stress corrosion cracking test using ammonia ‐ testing of components
DIN 54150 1977‐08
Non‐destructive testing ‐ impression methods for surface exami‐nation (Replica‐technique)
DVGW GW 2 2012‐05
DVGW‐system of rules – Connections of copper pipes for gas and water installations inside of estates and buildings
DVGW GW 541 2004‐10
Pipes made of non‐corroding steels and titan for drinking water installations ‐ Requirements and testing
The above listed standards are to be used in connection with the follow‐ing guidance documents:
DIN EN ISO 5817 2006‐10
Welding ‐ Fusion‐welded joints in steel, nickel, titanium and their alloys (beam welding ex‐cluded) ‐ Quality levels for imperfections
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 44/52Date of issue: 08.09.2015
DIN EN ISO 5817 2012‐06
Welding ‐ Fusion‐welded joints in steel, nickel, titanium and their alloys (beam welding ex‐cluded) ‐ Quality levels for imperfections
DIN EN ISO 6520‐1
2007‐11
Welding and allied processes ‐ Classification of geometric imperfections in metallic materials ‐ Part 1: Fusion welding
DIN EN ISO 18265 2014‐02
Metallic materials ‐ Conversion of hardness values
DIN 50600 1980‐03
Testing of metallic materials ‐ Metallographic Micrographs ‐ Picture scales and formats
DIN 50905 Teil 1 2009‐09
Corrosion of metals ‐ Corrosion testing ‐ Part 1: General guidance
DIN EN 12502‐1 2005‐03
Protection of metallic materials against corrosion ‐ Guidance on the assessment of corrosion likeli‐hood in water distribution and storage systems ‐ Part 1: General
DIN EN 12502‐2 2005‐03
Protection des matériaux métalliques contre la corrosion ‐ Recommandations pour l'évaluation du risque de corrosion dans les installations de distribution et stockage d'eau ‐ Partie 2: Facteurs à considérer pour le cuivre et les alliages de cuivre
DIN EN 12502‐3 2005‐03
Protection of metallic materials against corrosion ‐ Guidance on the assessment of corrosion likeli‐hood in water distribution and storage systems ‐ Part 3: Influencing factors for hot dip galvanised ferrous materials
DIN EN 12502‐4 2005‐03
Protection of metallic materials against corrosion ‐ Guidance on the assessment of corrosion likeli‐hood in water distribution and storage systems ‐ Part 4: Influencing factors for stainless steels
DIN EN 12502‐5 2005‐03
Protection of metallic materials against corrosion ‐ Guidance on the assessment of corrosion likeli‐hood in water distribution and storage systems ‐ Part 5: Influencing factors for cast iron, unalloyed and low alloyed steels
VDI 3822 2011‐11
VDI‐Guidance, Failure analysis ‐ Fundamentals and performance of failure analysis
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 45/52Date of issue: 08.09.2015
VDI 3822 Blatt 2 2008‐04
Failure analysis ‐ failures caused by mechanical‐working conditions
VDI 3822 Blatt 3 2007‐03
Failure analysis ‐ Failures caused by corrosion in electrolytes
VDI 3822 Blatt 1.4 2011‐10
Failures caused by thermal loading
3.9 Welding tests DIN EN 1320 1996‐12
Destructive tests on welds in metalllic materials ‐ Fracture test (withdrawn standard)
DIN EN ISO 9017 2013‐12
Destructive tests on welds in metallic materials ‐ Fracture test
DIN EN 13916 1996‐11
Welding ‐ Guidance on the measurement of preheating tempera‐ture, interpass temperature and preheat maintenance tempera‐ture
DIN EN 14555 2006‐12
Welding ‐ Arc stud welding of metallic materials
DIN EN 14555 2014‐08
Welding ‐ Arc stud welding of metallic materials
The above listed standards are to be used in connection with the follow‐ing guidance documents:
DIN EN 287‐1 2006‐06
Qualification testing of welders ‐ Fusion welding ‐ Part 1: Steels (withdrawn standard)
DIN EN ISO 9606‐1
2013‐12
Qualification testing of welders ‐ Fusion welding ‐ Part 1: Steels
DIN EN 287‐6 2010‐05
Qualification test of welders ‐ Fusion welding ‐ Part 6: Cast iron
DIN EN ISO 9606‐2 2005‐03
Qualification test of welders ‐ Fusion welding ‐ Part 2: Aluminium and aluminium alloys
DIN EN ISO 9606‐3
1999‐06 Approval testing of welders ‐ Fusion welding ‐ Part 3: Copper and copper alloys
DIN EN ISO 9606‐4
1999‐06 Approval testing of welders ‐ Fusion welding ‐ Part 4: Nickel and nickel alloys
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 46/52Date of issue: 08.09.2015
DIN EN ISO 17660‐1 2006‐12
Welding ‐ Welding of reinforcing steel ‐ Part 1: Load‐bearing welded joints
DIN EN ISO 17660‐2 2006‐12
Welding ‐ Welding of reinforcing steel ‐ Part 2: Non load‐bearing welded joints
DIN EN ISO 15607
2004‐03 Specification and qualification of welding proce‐dures for metallic materials ‐ General rules
DIN EN ISO 17637 2011‐05
Non‐destructive testing of welds ‐ Visual testing of fusion‐welded joints
DIN 1418 1998‐01
Welding personnel ‐ Approval testing of welding operators for fusion welding and resitance weld setters for fully mechanized and automatic weld‐ing of metallic materials (withdrawn standard)
DIN EN ISO 14732 2013‐12
Welding personnel ‐ Qualification testing of weld‐ing operators and weld setters for mechanized and automatic welding of metallic materials
DIN EN 15085‐3 2010‐01
Railway applications ‐ Welding of railway vehicles and components ‐ Part 3: Design requirements
DIN EN 15085‐5 2008‐01
Railway applications ‐ Welding of railway vehicles and components ‐ Part 5: Inspection, testing and documentation
DIN 18808 1984‐10
Steel structures ‐ structures made from hollow sections subjected to predominantly static load‐ing (withdrawn standard)
DIN EN 1993‐1‐1 2010‐12
Eurocode 3: Design of steel structures ‐ Part 1‐1: General rules and rules for buildings
DIN EN ISO 13919‐1 1996‐09
Welding ‐ Electrons and laser beam welded joints ‐ guidance on quality levels for imperfections ‐ Part 1: Steel
DIN EN ISO 5817 2006‐10
Welding ‐ Fusion‐welded joints in steel, nickel, titanium and their alloys (beam welding ex‐cluded) ‐ Quality levels for imperfections
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 47/52Date of issue: 08.09.2015
DIN EN ISO 5817 2014‐06
Welding ‐ Fusion‐welded joints in steel, nickel, titanium and their alloys (beam welding ex‐cluded) ‐ Quality levels for imperfections
DIN EN ISO 6520‐1 2007‐07
Welding and allied processes ‐ Classification of geometric imperfections in metallic materials ‐ Part 1: Fusion welding
DIN EN ISO 6520‐2 2002‐04
Welding and allied processes ‐ Classification of geometric imperfections in metallic materials ‐ Part 2: Welding with pressure
DIN EN ISO 10042 2006‐02
Welding ‐ Arc‐welded joints in aluminium and its alloys ‐ Quality levels for imperfections
DVS‐Richtlinie 1702 2009‐09
Procedure test at construction engineering
DVS‐IIW/EWF Richtlinie 1111‐1 2013‐07
International welder ‐ minimum requirements on training,testing and qualification ‐ Part I: general information, conditions, subject synopsis
DVS‐IIW/EWF Richtlinie 1111‐2 2013‐07
International welder ‐ minimum requirements on training,testing and qualification ‐ Part II: Rules and guidance for test objects
Richtlinie 97/23/EG 1997‐05
Directive of European Parliament and Council dated 27.05.1997 approximation of the laws oft he member states concerning pressure equip‐ment
AD 2000‐Merkblatt HP 32007‐02
Welding supervision, welders
TRD 201 1998‐06
Technical regulations for steam boilers Production welding of steel components Production ‐ Testing
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 48/52Date of issue: 08.09.2015
DIN EN ISO 17660‐1 2006‐12 + Corrigenda 1 2007‐08
Welding ‐ Welding of reinforcing steel ‐ Part 1: Load‐bearing welded joints
DIN EN ISO 17660‐2 2006‐12+ Corrigenda 1 2007‐08
Welding ‐ Welding of reinforcing steel ‐ Part 2: Non‐load‐bearing welded joints
DIN EN ISO 15614‐1 2005‐03
Specification and qualification of welding proce‐dures for metallic materials ‐ Welding procedure test ‐ Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys
DIN EN ISO 15614‐2 2005‐07
Specification and qualification of welding proce‐dures for metallic materials ‐ Welding procedure test ‐ Part 2: Arc welding of aluminium and its alloys
DIN EN ISO 15614‐3 2008‐06
Specification and qualification of welding proce‐dures for metallic materials ‐ Welding procedure test ‐ Part 3: Fusion welding of non‐alloyed and low‐alloyed cast irons
DIN EN ISO 15614‐4 2005‐09+ Corrigenda 1 2008‐01
Specification and qualification of welding proce‐dures for metallic materials ‐ Welding procedure test ‐ Part 4: Finishing welding of aluminium castings
DIN EN ISO 15614‐5 2004‐07
Specification and qualification of welding proce‐dures for metallic materials ‐ Welding procedure test ‐ Part 5: Arc welding of titanium, zirconium and their alloys
DIN EN ISO 15614‐6 2007‐01
Specification and qualification of welding proce‐dures for metallic materials ‐ Welding procedure test ‐ Part 6: Arc and gas welding of copper and its alloys
DIN EN ISO 15614‐7 2007‐09
Specification and qualification of welding proce‐dures for metallic materials ‐ Welding procedure test ‐ Part 7: Overlay welding
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 49/52Date of issue: 08.09.2015
E DIN EN ISO 15614‐7 2013‐10
Specification and qualification of welding proce‐dures for metallic materials ‐ Welding procedure test ‐ Part 7: Overlay welding
DIN EN ISO 15614‐8 2002‐06
Specification and qualification of welding proce‐dures for metallic materials ‐ Welding procedure test ‐ Part 8: Welding of tubes to tube‐plate joints
E DIN EN ISO 15614‐8 2014‐02
Specification and qualification of welding proce‐dures for metallic materials ‐ Welding procedure test ‐ Part 8: Welding of tubes to tube‐plate joints
DIN 2303 2007‐02
Welding and allied processes ‐ Quality require‐ments for production and maintenance compa‐nies for military products
DIN EN ISO 25239‐1 2012‐03
Friction stir welding ‐ Aluminium ‐ Part 1: Vo‐cabulary
DIN EN ISO 25239‐2 2012‐03
Friction stir welding ‐ Aluminium ‐ Part 2: Design of weld joints
DIN EN ISO 25239‐3 2012‐03
Friction stir welding ‐ Aluminium ‐ Part 3: Qualifi‐cation of welding operators
DIN EN ISO 25239‐4 2012‐03
Friction stir welding ‐ Aluminium ‐ Part 4: Specifi‐cation and qualification of welding procedures
DIN EN ISO 25239‐5 2012‐03
Friction stir welding ‐ Aluminium ‐ Part 5: Quality and inspection requirements
DIN EN ISO 3834‐1 2006‐03
Quality requirements for fusion welding of metal‐lic materials ‐ Part 1: Criteria for the selection of the appropriate level of quality requirements
DIN EN ISO 3834‐2
2006‐03 Quality requirements for fusion welding of metal‐lic materials ‐ Part 2: Comprehensive quality requirements
DIN EN ISO 3834‐3 2006‐03
Quality requirements for fusion welding for me‐tallic materials ‐ Part 3: Standard quality re‐quirements
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 50/52Date of issue: 08.09.2015
DIN EN ISO 3834‐4 2006‐03
Quality requirements for fusion welding of metal‐lic materials ‐ Part 4: Elementary quality re‐quirements
DIN EN ISO 3834‐5 2006‐03 + Corrigenda 1 2009‐04
Quality requirements for fusion welding of metal‐lic materials ‐ Part 5: Documents with which it is necessary to conform to claim conformity to the quality requirements
E DIN EN ISO 3834‐5 2014‐02
Quality requirements for fusion welding of metal‐lic materials ‐ Part 5: Documents with which it is necessary to conform to claim conformity to the quality requirements
DIN EN 1090‐1 2012‐02
Execution of steel structures and aluminium structures ‐ Part 1: Requirements for conformity assessment of structural components
DIN EN 1090‐2 2011‐10
Execution of steel structures and aluminium structures ‐ Part 2: Technical requirements for steel structures
DIN EN 1090‐3 2008‐09
Execution of steel structures and aluminium struc‐tures ‐ Part 3: Technical requirements for alumin‐ium structures
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 51/52Date of issue: 08.09.2015
4 Testing of construction products and testing of fire resistance within the framework of Regulation (EU) No. 305/2011 laying down harmonised conditions for the marketing of construction products (Construction Products Regulation ‐ CPR)
Decision / Resolution of the Commission
System1) Technical Specification
1995/467/EC Gypsum products
3
EN 520:2004 + A1:2009 Gypsum plasterboards ‐ Definitions, requirements and test method
EN 14195:2005/AC:2006 Metal framing components for gypsum board systems ‐ Defi‐nitions, requirements and test methods
1997/176/EC Products from structural timber
3 EN 14592:2008 + A1:2012 Timber structures ‐ Dowel‐type fasteners ‐ Requirements
1997/464/EC/ 2004/663/EC Products for sanitation outside buildings
3
EN 1433:2002 + A1:2005 Drainage channels for vehicular and pedestrian areas ‐ Classi‐fication, design and testing requirements, marking and evaluation of conformity
1997/740/EC Masonry and related products
3
EN 845‐1:2003 + A1:2008 Specification for ancillary components for masonry ‐ Part 1: Wall ties, tension straps, hangers and brackets
EN 845‐2:2003 Specification for ancillary components for masonry ‐ Part 2: Lintels
EN 845‐3:2003 + A1:2008 Specifications for ancillary components for masonry ‐ Part 3: Bed joint reinforcement of steel meshwork
1997/808/EC Flooring
3
EN 13454‐1:2004 Binders, composite binders and factory made mixtures for floor screeds based on calcium sulfate ‐ Part 2: Test methods
1998/213/EC Internal partition kits
3
ETAG 003:1999 Guideline for European technical approval for internal parti‐tion kits use as non‐loadbearing walls
1998/437/EC Wall and ceiling finishes for internal and external areas
3 EN 13964:2004 + A1:2006 Suspended ceilings ‐ Requirements and test methods
Annex to the Accreditation Certificate D‐PL‐11117‐01‐00
Period of validity: 08.09.2015 to 10.04.2019 ‐ Translation ‐ 52/52Date of issue: 08.09.2015
Decision / Resolution of the Commission
System1) Technical Specification
1999/91/EC thermal insulating pro‐ducts
3
EN 14316‐1:2004 Thermal insulation products for buildings ‐ In‐situ thermal in‐sulation formed from expanded perlite (EP) products ‐ Part 1: Specification for bonded and loose‐fill products before instal‐lation
1999/470/EC Construction adhesives
3
EN 12004:2007 + A1:2012 Adhesives for tiles ‐ Requirements, evaluation of conformity, classification and designation
1999/472/EC
pipes, tanks and ancillar‐ies not in contact with water intended for hu‐man consumption
3
EN 1057:2006 + A1:2010 Copper and copper alloys ‐ Seamless, round copper tubes for water and gas in sanitary and heating applications EN 10255:2004 + A1:2007 Non‐alloy steel tubes suitable for welding and threading‐ Technical delivery conditions
1) System for the assessment and verification of constancy of performance
The requirements for a testing labaratory according to article 43 of regulation (EU) 305/2011 laying down harmonised conditions for the marketing of construction are fulfilled. Test proce‐dures for which a determination of the product type is needed and which will not be car‐ried out by the holder of this certificate are named in a list of subcontractors. Abbreviations used:
DAfStB German Committe for reinforcing steel DIBt Competence Centre for Construction DGGT German Society for Earth and Foundation Works DIN German Institute for Standardisation DVGW German Association of Gas and Water Experts EN European Standard FGSV Research Society for Roads and Traffic Engineering GDA E 3‐12
Recommendation for geotechnical acceptability: E 3‐12 Acceptability of mineral drainage layers
ISO International Organisation for Standardisation ÖNORM Austrian Standard RAL German Institute for Quality Control and Labelling TP Asphalt ‐ St B Technical test specification for Asphalt TP Gestein ‐ StB Technical test specification for aggregates in road works VDI Association of German Engineers ZEB Status monitoring and evaluation of tracks surfaces of roads ZTV Asphalt ‐ StB 07 Additional technical contractual conditions and guidelines for construction
of asphalt traffic surfaces ZTV‐SIB Additional technical contractual conditions and guidelines for protection
and restoration of concrete structural components QMA x.x.xxx Work Instruction of TÜV Rheinland LGA Bautechnik GmbH