global wire mesh security part
TRANSCRIPT
globalindustrial.com
WIRE MESH SECURITY PARTITION
AssemblyInstructions
Customer Service1-800-645-2986
PANEL PARTS
DOOR PARTS
Floor Socket Wall Clip Top CappingSplice Plate
Top CappingCorner Splice Plate
3-Way Splice Plate 3-Way Clip
Corner Post Channel StiffenerPost
Fill-A-Gap Panel
Latch Receiver(Already Attached)
Bottom Slam(Already Attached)
Track Hanger
Track Hanger Splice Hanger
Wheel Trolley Slide Lock(Already Installed)
Swing Lock(Already Installed)
Top CappingChannel
ROOF PARTS
Roof Beam Roof Beam Splice Beam SupportBracket
Roof MountingAngle
Yoke Bracket(Included As part Of
Roof Beam Splice Kit)
Wall Mount Slotted Angle
WIRE MESH SECURITY PARTITIONAssembly Instructions1-800-645-2986
ROOF PANEL
CHANNEL STIFFENER
CHANNEL STIFFENER POST
DETAIL “E”
ROOF PANEL
SEE DETAIL “E”
Attach yoke bracketto channel
stiffener post.
Assemble roof panels.Bolt panels to roofmounting angle androof beam.
Tighten all nuts and bolts.
WITH WARNINGLABEL
FACING UP6 7
9NOTE:MAKE SURE THAT CHANNEL STIFFENERPOST ARE IN A PLUMB POSITION BY USINGA LEVELING DEVICE ON (2) SIDES OF THECHANNEL STIFFENER POST.
Attach channelstiffener post atjunction of 4 roofpanels. Post must besecured to floor(hardware notsupplied).
8
8 1
Global Wire Mesh Security Part 1/31/05 11:36 AM Page 1
WIRE MESH SECURITY PARTITIONAssembly Instructions1-800-645-2986
5'
5'
5'
5'
5' 5' 5' 5'23'7"
5'
5'
20'
3'
FLEX -O-PANEL
HINGED DOOR
SLIDINGDOOR
WALL CLIPSWALL CLIPS
SERVICEWINDOW
MASONRY WALL
CHANNELSTIFFENER
CHANNELSTIFFENER
CHANNELSTIFFENER
5'
5'
7"
HOW TO PLAN AND ORDER1. Make a rough floor plan of the area to be enclosed and
take measurements showing them on the drawing.
2. Indicate panels, doors, service windows, size andlocation of doors on the drawing. Show the direction ofthe door slide or hinges either left or right handed,swinging in or out.
3. At least 2 people required to assemble partition.
4. Snap chalk lines indicating walls.
5. If starting at an existing wall, start first panel from wall.If it is a free-standing room, start at a corner.
6. Bolt panels together loosely. DO NOT secure floorsockets to the floor until fully assembled.
7. Install channel stiffener posts every 10-15 feet. Channelstiffener posts are included with doors. See drawing forplacement.
8. After all panels and doors are assembled, attach topcapping channel. Top capping channel should spanpanels and splices should be in the middle of a panel formaximum strength. For rooms with roofs see page 5 forassembly instructions.
9. Tighten panel bolts.
10. Attach floor sockets using appropriate hardware(NOT Included)
WIRE MESH SECURITY PARTITIONAssembly Instructions1-800-645-2986
ALIGN SURFACES
SEE DETAIL “C”
SEE DETAIL “A” AND “B”
SEE DETAIL “D”
DETAIL “C”
DETAIL “B”
CUT ANGLEDETAIL “A”
DETAIL “D”
Attach wall mount slotted angle to wall
(hardware notincluded).
ROOF ASSEMBLYAttach roof mounting angles to wire partition walls.4
5
WALL CLIPS WALL CLIPS
SLIDINGDOOR
CHANNELSTIFFENER
CHANNELSTIFFENER
CHANNELSTIFFENER
SERVICEWINDOW
FILL-A-
GAPPANEL
HINGEDDOOR
72
Global Wire Mesh Security Part 1/31/05 11:36 AM Page 3
WIRE MESH SECURITY PARTITIONAssembly Instructions1-800-645-2986
PANEL ASSEMBLY
WALL CLIPINSTALLATION
ADJUSTABLEFILL-A-GAP
PANEL
TOP CAPPINGCHANNEL
TOPCAPPING
If predrilled holes do not line up,drill a 5/16” hole
Bolt panels together loosely.DO NOT secure floor socketsto the floor until fullyassembled.
Floor SocketInstallation
3-Way ClipInstallation
3-Way Splice Plate Channel StiffenerInstallation
Panel to Panel BoltHole Alignment
Trim leg abovefloor socket for3 way clipinstallation
WIRE MESH SECURITY PARTITIONAssembly Instructions1-800-645-2986
ROOF ASSEMBLY
ROOF BEAMASSEMBLY
Assemble splicer to roof beams.
Attach beam support bracket to roof beam.
Attach roof beamassembly to wirepartition.
-Rooms with a roof do not use top capping-
12
3
6 3
Global Wire Mesh Security Part 1/31/05 11:36 AM Page 5
WIRE MESH SECURITY PARTITIONAssembly Instructions1-800-645-2986
SLIDE DOOR ASSEMBLY
ChannelStiffener
REVERSIBLE DOOR
HangBar
HangBar
Strike platebolted tochannelstiffeners
Hinged Left Swing Out
Hinged RightSwing In
Hinged Left Swing In
Hinged LeftSwing In
LatchReceiver
TransomBar
BottomSlam
BottomTrack
Remove lockand reverse if
necessary
WIRE MESH SECURITY PARTITIONAssembly Instructions1-800-645-2986
ROOF BEAM LAYOUT CHART
54
Global Wire Mesh Security Part 1/31/05 11:36 AM Page 7