BRINGING MONOLITHIC TO LIFEesthetic finishing system

Getting Startedinstructions for use

Inspired by

esthetics reimagined.

SYSTEMOVERVIEW

With the MiYO™ Esthetic Finishing Systemyour laboratory team can quickly & easilycreate anatomically correct, beautifulrestorations and achieve all of the same effectsfound in natural teeth with a simple paintingapplication process.

5 structure17 color pastes

1 insync glaze paste1 powder stain

page 1

®

color

FIRINGSCHEDULE

One Shot & Structure Technique(One or multiple firings)

Pre-color Preparation:Surface should be clean and free from contaminants.

Before Use:• IMPORTANT: Do not pour out liquid that may accumulate at top of jar.• MIX ALL MATERIALS THOROUGHLY BEFORE USE EVERY DAY to maintain consistency and proper handling properties throughout the life of the jar.• Do not bring InSync Glaze or MiYO color pastes in contact with water! Contact with water will change the refractive index of liquid and will alter the appearance of colors while wet. • Always use a clean brush.• STRUCTURE MATERIAL ONLY: Use water to clean off your brush prior to and during application.

Intended Use:A Type 1, class 1b ceramic for the coloring, enhancing, and glazing of the following restoration types: Zirconia and Lithium Disilicate.

CTE:CTE (25-500°C) [*10-6 K-1] ± 1.0: MiYO Colors & Structure 7.4 (2x) CTE (25-500°C) [*10-6 K-1] ± 0.5: InSync Glaze 7.3 (1x)

Storage:Store under dry conditions, +12°C to +38°C

*Firing parameters represent standard values and may need to be adjusted. *Final results should be the determining factor in furnace adjustments.

MiYO™ Colors & InSync Glaze*(paste or spray)

MiYO Structure*

4 6 450 580 45 760 1(air)

6 450 620 45 710 1(air)

Entry Time(min)

LowTemp(°C)

VacStart(°C)

HeatRate

(°C/min)

High Temp(°C)

Hold Time(min)

page 3

Dry Time(min)

Entry Time(min)

LowTemp(°C)

VacStart(°C)

High Temp(°C)

Hold Time(min)

Dry Time(min)

MiYO™ Structure*

HeatRate

(°C/min)

4 6 550 550 55 720 1(air)*Multiple unit bridges may require a small increase in firing temperature.

Inhalation of ceramic dust can be hazardous to your health.

2 TECHNIQUES

basic coloring and glaze in 1 firing

basic coloring, additional characterizationand structure to add depth in 2 firings

ONE SHOT

STRUCTURE

technique

technique

6 450 620 45 710 1(air)

page 4

4 6 550 550 55 720 1(air)

Apply a thin layer of liquid or glaze paste on restorationprior to adding colors.

*Choose the target value from translucent A, B, C, D. **Translucent storm or smoke can be used.

ONE SHOT Technique

page 5

translucent storm**

translucent A*

target value

basic method

Apply a thin layer of liquid or glaze paste on restorationprior to adding colors.

*Choose the target value from translucent A, B, C, D. **Translucent storm or smoke can be used.

ONE SHOT Technique

Apply all other characterization and fire.

page 6

translucent clementine

translucent lumin

translucent storm

mamelon coral

mamelon pumpkin

halo spring

stain linen

translucent storm**

translucent A*

characterization

ONE SHOT TechniqueFor added depth & translucency, you have the option to spray InSync Spray Glaze over the entire wet surface prior to firing.

Do Not spray directly on the restoration to avoid orange peel texture.

Do NOT use InSync paste glaze with one shot technique as appliedstains will puddle and run leaving less than desirable results.

page 7

ONE SHOT Technique

Finished restoration with MiYO.

page 8

page 9

STRUCTURE Technique

Add color where desired.

3 value zonestranslucent storm

translucent straw

translucent clementine

page 10

Begin characterization.

characterization 1

STRUCTURE Technique

mamelon coral

translucent storm

translucent storm

translucent straw

translucent clementine

page 11

STRUCTURE Technique

Finish creating additional effects and fire.

characterization 2halo spring

stain linen

STRUCTURE Technique

Fired look of the MiYO restoration after 1st firing.

page 12

halo spring

stain linen

STRUCTURE Technique

page 13

If esthetics have been achieved, applyone or more of the structure pastes evenlyacross the entire labial surface. Then createsurface texture with a brush.

structurestructure window

STRUCTURE Technique

page 14

Apply Ice to enhance bluish translucency effect.Mix structure window & halo spring (1:1 ratio).

structure

OPTIONALfor adding extra depth

ice

window/halo spring

structure window

STRUCTURE TechniqueOPTIONAL

raising value

Apply structure ghost to raise value withoutgreying and fire.

structure

page 15

structure ghost

page 16

STRUCTURE Technique

FINISHED MiYO restoration with structure and additional effects.

structure ghost

page 17

STRUCTURE Technique

To manually create different surface luster and texture, you can also:

- use a rubber wheel and diamond paste- pumice like traditionally layered ceramic

page 18

STRUCTURE

ONE-SHOT

make it your own

Jensen DentalNorth Haven, CT 064732017-11-9 Rev. 2

www.jensendental.com800-243-2000