gallagher addendum 3
TRANSCRIPT
This addendum is being furnished by the Construction Manager for clarification purposes only and shall become and is part of the Contract Documents.
New Elementary School #10 – Phase 1 Addendum #3 –December 14, 2021
Page 1 of 1
ADDENDUM NO. 3
TO THE CONTRACT DOCUMENTS FOR: NEW ELEMENTARY SCHOOL #10 – PHASE 1
FORNEY ISD DECEMBER 14, 2021
GENERAL CLARIFICATIONS TO ALL PROPOSERS
1. NEW ELEMENTARY SCHOOL #10 – PHASE 1 – HUCKABEE ARCHITECTS ADDENDUM NO. 3: The attached Addendum No. 3 to the Drawings and Specifications for Forney ISD – New Elementary School #10, as prepared by Huckabee Architects and dated December 14, 2021 is included in this Addendum and shall become a part of the Contract Documents for this project.
2. REVISED BID FORM TO INCLUDE ALTERNATE #3 – ALTERNATE RTU MANUFACTURERS
A REMINDER TO EACH BIDDER: Please review the Gallagher “Contract Conditions and CSP Package Scope of Work” specification Volume #1 in its entirety. Reference the bid package as it pertains to your scope, submit your proposal on the bid form provided within this specification. Include the performance & payment bond costs in your base bid (if proposal is more the $25,000).
CLARIFICATIONS AND CHANGES TO SECTION 01 81 00 SCOPE OF WORK
1. CLARIFICATION TO CSP Bid Package 23-A, MECHANICAL: PLUMBING AND HVAC: A. Include Alternate #3 as part of this Bid Package. See revised bid form.
GALLAGHER
Forney ISD – New Elementary School Ten North-Package 1 Section 00 41 00 Construction Proposal Form Page 1 of 5
CONSTRUCTION PROPOSAL FORM ALL PAGES MUST BE COMPLETED AND INITIALED!
ORGANIZATION OPERATING AS:
Corporation, organized under laws of the State of_________________________________
Partnership
Individual
Joint Venture consisting of the firms of: _______________
Other (specify):
ADDENDUM ACKNOWLEDGMENT (the undersigned acknowledges receipt of the following addenda):
ADDENDUM NO. DATE ADDENDUM NO. DATE
_______________ _______________ _______________ _______________
_______________ _______________ _______________ _______________
_______________ _______________ _______________ _______________
PROPOSER PROPOSES:
In response to the Advertisement to submit a PROPOSAL for the execution of the Work described by the Drawings and Specifications entitled NEW ELEMENTARY SCHOOL TEN NORTH-PACKAGE 1 and having examined the site where the work is to be performed and being familiar with local conditions as they might in any way affect the cost and/or execution of the Work and having carefully examined all of the Drawings, Specifications, Request for Proposal Scope of Work and other related documents and Addendum(s) thereto, the undersigned Proposer agrees to provide all labor, materials, equipment and services including transportation and other facilities as may be required for the complete and satisfactory execution of the Work for which this Proposal is submitted for the lump-sum consideration as stated hereinafter.
PROJECT: NEW ELEMENTARY SCHOOL TEN – PACKAGE 1
FORNEY INDEPENDENT SCHOOL DISTRICT, FORNEY, TX
TO: FORNEY INDEPENDENT SCHOOL DISTRICT 600 S. BOIS D’ARC STREET FORNEY, TX 75126
FROM: CONTRACTOR NAME:
PHYSICAL ADDRESS:
CITY, STATE, ZIP:
AREA CODE / PHONE:
CONTACT NAME:
E-MAIL ADDRESS:
GALLAGHER
Forney ISD – New Elementary School Ten North-Package 1 Section 00 41 00 Construction Proposal Form Page 2 of 5
Note: All Proposal amounts shall include all applicable bond costs.
CSP # DESCRIPTION TOTAL
(including bonds)
CSP 01-B Final Building Cleaning $
CSP 03-A Building Concrete $
CSP 03-C Pre-Cast Concrete $
CSP 04-A Masonry $
CSP 05-A Structural Steel & Erection $
CSP 06-A Millwork $
CSP 07-A Roofing and Sheetmetal $
CSP 07-C Sprayed Insulation $
CSP 08-A Frames, Doors & Hardware $
CSP 08-B Glass & Glazing $
CSP 08-C Overhead Coiling Doors & Grilles $
CSP 09-A Drywall & Acoustical $
CSP 09-C Tiling $
CSP 09-D Floor Coverings $
CSP 09-E Painting & Wallcovering $
CSP 09-H Sheet Vinyl Flooring $
CSP 10-A Building Specialties $
CSP 10-D Metal Lockers $
CSP 10-G Identification Devices $
CSP 10-H Folding Partitions $
CSP 11-A Food Service Equipment $
CSP 11-E Athletic Equipment $
CSP 12-D Window Treatments $
CSP 14-A Elevators $
CSP 21-A Fire Sprinkler System $
CSP 23-A Mechanical: Plumbing & HVAC $
CSP 26-A Electrical $
CSP 27-A Voice and Data Cabling $
CSP 27-B Audio/Visual Systems $
Contractor Name: Initials:
GALLAGHER
Forney ISD – New Elementary School Ten North-Package 1 Section 00 41 00 Construction Proposal Form Page 3 of 5
CSP # DESCRIPTION TOTAL
(including bonds)
CSP 27-C Communication Systems $
CSP 28-A Fire Alarm Systems $
CSP 28-B Security Systems $
CSP 31-E Termite Control $
COMBINATION PROPOSALS CSP Package No. CSP Package No. CSP Package No. CSP Package No.
____________ ____________ _____________ ___________
TOTAL COMBINATION PROPOSAL AMOUNT $ ____________________________
ALTERNATES REFER TO SPECIFICATION SECTION 01 23 00 FOR COMPLETE DESCRIPTION
ALTERNATE #1 AUGER CAST GROUT PILES
CSP PACKAGE #________ ADD $ ___________________________
DEDUCT $____________________________
ALTERNATE #2 PIER CASING
CSP PACKAGE #________ DEDUCT $ ___________________________
ALTERNATE #3 ALTERNATE RTU MANUFACTURER – BASE BID SHALL BE AAON – PROVIDE ALTERNATE
FOR OTHER MANUFACTURERS
CSP PACKAGE #________ MANUFACTURER NAME ________________
ADD/DEDUCT $ _____________________
Contractor Name: Initials:
GALLAGHER
Forney ISD – New Elementary School Ten North-Package 1 Section 00 41 00 Construction Proposal Form Page 4 of 5
PIER PRICING UNIT PRICES FOR PIERS: Unit prices include all materials, equipment, labor, insurance, overhead, profit, warranties, etc. to perform the required work according to the Project Documents (Lineal foot adjustments by Geotechnical Engineer: Adjustments determined on total estimated quantity and not per individual pier. Deduct amount shall not be less than 60% of Add amount).
STRAIGHT SHAFT PIERS ADD DEDUCT DELETE CASING
24” $ /LF 24” $ /LF 24” $ /LF AUGER CAST PILES
ADD DEDUCT 24” $ /LF 24” $ /LF
CSP 05-A, STRUCTURAL STEEL & ERECTION REQUEST FOR DELIVERY DATES & PROPOSED STEEL ERECTOR
THIS INFORMATION MAY BE USED IN DETERMINING THE BEST VALUE FOR FISD (PROVIDE DATES BASED ON JANUARY 14, 2021 NOTICE TO PROCEED)
Start Date Duration
AB/Embed Shop Drawing Delivery: _______________________________________
Steel Joist/Metal Deck Shop Drawing Delivery: _______________________________________
Structural Steel Shop Drawing Delivery: _______________________________________
Misc. Steel Shop Drawing Delivery: _______________________________________
Anchor Bolts/Embed Delivery: _______________________________________
Structural Steel Delivery: _______________________________________
Steel Joist/Metal Deck Delivery: _______________________________________
Miscellaneous Steel Delivery: _______________________________________
Proposed Steel Erector: _______________________________________
Second Proposed Steel Erector: _______________________________________
Additional Cost for Second Proposed Steel Erector: _______________________________________
SUPPLEMENTAL PRICING REQUESTED Unit Pricing: This proposal contractor shall furnish a per bag price to install latex floor leveling compound. (price includes all labor, materials, equipment, overhead, profit, taxes, insurance, bonds, etc.)
CSP 09-C/CSP 09-D/CSP 09-H ADD $ Per 50 lb. Bag Unit Pricing: This proposal contractor shall furnish a per bag price to install feather finish floor leveling compound. (price includes all labor, materials, equipment, overhead, profit, taxes, insurance, bonds, etc.)
CSP 09-C/CSP 09-D/CSP 09-H ADD $ Per 10 lb. Bag
Contractor Name: Initials:
GALLAGHER
Forney ISD – New Elementary School Ten North-Package 1 Section 00 41 00 Construction Proposal Form Page 5 of 5
GENERAL:
No modifications, additions or deletions shall be made to this Construction Proposal Form. In submitting this Proposal Proposer represents that all materials, equipment, and services associated with the Work as well as the terms and conditions of the proposed contract shall be in strict conformance with the Project Documents on which this Proposal is based.
The Proposer agrees that a complete set of Contract Documents (specifications, plans, addendums, etc.) have been reviewed before submitting this Proposal.
The Proposer agrees that if a POST PROPOSAL CONFERENCE INTERVIEW is extended to the Proposer it will, in a diligent manner, forward a recent AIA Document A305 Contractor’s Qualification Statement and a Sample Certificate of Insurance to the Owner’s Representative prior to the Scheduled meeting Time.
The Proposer agrees that if notice of award is extended to the Proposer it will, in a diligent manner, execute the Contract Form as identified within the project manual without modification and deliver the required:
• Contract, • Surety Bonds that are in compliance with Chapter 2253 of the Texas Government Code, and • Insurance Certificates that are in compliance with the Owner’s stated requirements.
within five (5) days following presentation of the Contract.
The Proposer agrees that this Proposal shall not be withdrawn for a period of sixty (60) days after it has been opened without the express permission of the Owner.
The Proposer understands that the Owner reserves the right to reject any or all Proposals, to waive informalities in connection therewith, and to award the Contract for any of the Work or the project as a whole.
In submitting this Proposal the Proposer represents that no person, persons or company other than the firm listed below or otherwise indicated hereinafter has any interest whatsoever in this Proposal or the Contract that may be entered into as a result thereof.
The Proposer further represents that the proposing entity has complied with all City, County, State and Federal regulations for conducting the business operations for which it has Proposal and will be in full legal compliance therewith if awarded the Contract.
The undersigned agrees to complete all the Work within time limits after the date of the Notice to Proceed according to the substantial completion time set forth and that if the Work is not complete within the time limit set forth the Owner may assess liquidated damages pursuant to each individual Request for Proposal.
The undersigned declares that the person(s) signing this Proposal is fully authorized to sign on behalf of the named firm and to fully bind the firm to all conditions and provisions thereof.
LABOR UNIT PRICING Each Proposal Contractor shall submit hourly rates for field labor for this project:(unit price includes all labor, overhead, profit, taxes, insurance, bonds, etc.)
REGULAR OVERTIME
CSP ___________ GENERAL LABOR $ $ Per Hour
CSP ___________ APPRENTICE/HELPER $ $ Per Hour
CSP ___________ JOURNEYMAN/MECHANIC $ $ Per Hour
CSP ___________ SUPERVISOR/FOREMAN $ $ Per Hour
GALLAGHER
Forney ISD – New Elementary School Ten North-Package 1 Section 00 41 00 Construction Proposal Form Page 6 of 5
AUTHORIZED PERSON E-MAIL ADDRESS:
ATTACHMENTS:
CONFLICT OF INTEREST FORM
W9 FORM
DATE SUBMITTED: _________________________________________________________ , 2021
FIRM: _______________________________________________________________
BY (SIGNATURE): _______________________________________________________________
PRINT SIGNATURE: _______________________________________________________________
TITLE: _______________________________________________________________
PERSON AUTHORIZED TO EXECUTE CONTRACT: NAME:________________________/TITLE:__________________________
NO. 3
TO THE DRAWINGS AND THE PROJECT MANUAL
PROJECT NAME: New Elementary School Ten North – Phase One
CLIENT NAME: Forney Independent School District
LOCATION: Forney, Texas
PROJECT NUMBER: 1824-21-01
PROPOSAL DATE: December 16, 2021
ADDENDUM DATE: December 14, 2021
For additional information regarding this project, contact Kate Dunfee at 800.687.1229.
THIS ADDENDUM INCLUDES:
Civil Items 0 Pages
Landscape Items 0 Pages
Structural Items 0 Pages
Architectural Items 1 Page
Foodservice Items 0 Pages
Plumbing Items 0 Pages
Mechanical Items 0 Pages
Electrical Items 0 Pages
Technology Items 0 Pages
AND ALL ATTACHED REVISED DRAWING REFERENCES IN THE ADDENDUM
04.01.2012.14.2021
Project Name: New Elementary School Ten North
Client: Forney Independent School District
Forney, Texas
Project Number: 1824-21-01
Architectural Items For
Addendum No. 3
Page 1 of 1
ARCHITECTURAL ITEMS FOR ADDENDUM NO. 3 NOTICE TO PROPOSERS:
A. This Addendum shall be considered part of the contract documents for the above-mentioned project as though it had
been issued at the same time and incorporated integrally therewith. Where provisions of the following supplementary
data differ from those of the original contract documents, this Addendum shall govern and take precedence.
B. Proposers are hereby notified that they shall make any necessary adjustments in their estimate on account of this
Addendum. It will be construed that each Proposer’s proposal is submitted with full knowledge of all modifications and
supplemental data specified therein. Acknowledge receipt of this addendum in the space provided on the proposal
form. Failure to do so may subject Proposer to disqualification.
REFERENCE IS MADE TO THE DRAWINGS AND THE PROJECT MANUAL AS NOTED:
PROJECT MANUAL:
AD No 3, Arch. Item 1: To the Project Manual, Section 01 6210, “SCHEDULE OF MATERIALS AND COLORS,”
For bidding purposes, carpet will be selected from the Color Field Collection as manufactured by Milliken.
AD No 3, Arch. Item 2: To the Project Manual, Section 08 7100, “DOOR HARDWARE,”
Replace this section in its entirety, as issued per this addendum. (33 pages) For clarification, the following revisions have been
made:
1. Removal of non-Allegion product from specifications
2. Added Hardware Types W708, W700C, WDE714 and WD205I
AD No 3, Arch. Item 3: To the Project Manual, Section 09 9000, “PAINTING AND COATING,”
To part 4.02 Revise Subparagraph DD to read as follows:
DD. Code 120 – Structural Steel and Deck in Crawl Space
1. Surface Preparation: SSPC SP-6 Commercial Metal Blast, 2-3 mil profile.
2. 1st Coat: SW, Zinc Clad 4100 applied at 3-5 mils dry film thickness.
DRAWINGS:
AD No 3, Arch. Item 4: To the Drawings, Sheets A3.1, “OPENING SCHEDULES, CONFIGURATIONS AND DETAILS” and
A3.6, “DOOR SCHED & DETAILS – TORNADO SHELTER”,
Replace the hardware schedule in its entirety, as issued per this addendum. For clarification, the following revisions have
been made:
1. Door 1.21 shall not be rated.
2. Add Door 1.40A to the door schedule and the hardware schedule: (3’-0” x 7’-0”) PL-FL Door, HM-A Frame
3. Add Doors 3.17 A, B, C & 3.19B to the hardware schedule.
4. Delete magnetic hold open from door 3.17B
5. Delete Door 3.39 from the hardware schedule
END OF ARCHITECTURAL ADDENDUM
04.01.2012.14.2021
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 1 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
SECTION 087100
DOOR HARDWARE
PART 1 - GENERAL 1.01 WORK INCLUDED The work in this section shall include the furnishing of all items of door hardware as hereinafter
specified, or obviously necessary to complete the building, except those items which are specifically excluded from this section of the specification.
1.02 DESCRIPTION OF WORK
Door Hardware - Hardware used in building construction but particularly that used on or in
connection with doors and frames, cabinets and other movable members. It also has a finished appearance as well as functional purpose and may be considered as a part of the decorative treatment of a room or building.
1.03 RELATED WORK
A. Documents affecting work of this Section include, but are not necessarily limited to, General Conditions, Supplementary Conditions, and Sections in Division 1 of these specifications.
B. Related Sections: Section 081000 - Steel Doors and Frames Section 081000 – Standard Steel Frames Section 082100 – Flush Wood Doors Section 082120 – Stile and Rail Wood Doors Section 082150 – Plastic Faced Wood Doors Section 083300 - Coiling Doors and Grilles
1.04 QUALITY ASSURANCE A. Hardware has been specified herein by manufacturer's name, brand and catalog numbers
for the purpose of establishing a basis for quality, finish, design and operational function. To insure a uniform basis of acceptable material, it is the intention that only manufacturer's items specified as "Acceptable and Approved" be furnished for use on this project.
B. Substitutions: Request for substitutions of items of hardware not listed as "Acceptable and
Approved" shall be made to the Architect no later than ten (10) days prior to bid opening. Approval of substitutions will only be in writing or by addenda. Request for substitutions shall be accompanied by samples and/or detailed information as to the manufacturer of the product.
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 2 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
C. Underwriters' Laboratories Requirements: Hardware for openings classed as requiring a UL label in the door schedule, or by code, shall be furnished and installed to meet the applicable requirements of NFPA 80. Hardware shall be UL listed for usage with types and sizes of fire doors specified and scheduled. Products tested shall meet requirements of UBC 7-2-1997 / UL10C
D. Accessibility Standards: Hardware shall be in conformance with Article 9102, Texas Civil
Statutes, Elimination of Architectural Barriers Act of Texas. 1. Door Closers: The sweep period of closers shall be adjusted so that from an open
position of 90 degrees, the door will take at least five seconds to move to an open position of approximately 12 degrees.
2. The maximum force for pushing or pulling open door shall be as follows: a. Exterior hinged doors: Not to exceed 8.5 lbf. b. Sliding, folding, and interior hinged doors: Not to exceed 5 lbf. c. Fire doors: Adjusted to meet minimum closing force permitted by governing fire
safety standards. E. Federal Accessibility Standards: Hardware shall be in accordance will all requirements of
the Americans With Disabilities Act - 1990. F. Supplier: A recognized builders hardware supplier who has been furnishing hardware in
the project's vicinity for a period of not less than two (2) years, and who is, or has in employment, a Hardware Consultant (AHC) in good standing as certified by the Door and Hardware Institute. This consultant shall have experience in the preparation of architectural hardware specifications, estimating, detailing, ordering, servicing of architectural hardware in all its branches and will be available at reasonable times during the course of the work for project hardware consultation to the Owner, Architect and Contractor. It is the hardware distributor’s responsibility to coordinate the hardware specified to work with the Aluminum doors.
G. Pre-Installation Instructional Meeting: Contractor shall schedule and hold a pre-installation
meeting that includes the Contractor, the Architect and/or his chosen representative, the Hardware Supplier, and all installers of hardware. Instructional meeting shall be conducted by the Hardware Supplier, covering proper installation of all items of hardware to be incorporated into the Project.
H. Installer: Firm with a minimum of five years of documented experience in installing the types
and grade of hardware being incorporated into the Project. Three written references from Construction Administrators of previous projects required for the Architect’s review before installation Contract or Subcontract is executed.
I. Prototype Installations: One of each type of the following hardware installations shall be
performed to the Architect’s (and/or his designated representative’s) approval before any installations of like-type applications are performed:
1. One exterior door pair with exit devices 2. One exterior single door with an exit device
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 3 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
3. One single classroom door 4. One interior pair of doors with vertical rod exit devices 1.05 REFERENCES A. Door Hardware in this section shall meet the following as established by the American
National Standards Institute, Inc. (ANSI) which is sponsored by the Builders Hardware Manufacturers Association, Inc., (BHMA). Product tests are to be administered by the ETL Testing Laboratories, Inc., or other official testing laboratories which have been designed by BHMA for the testing of ANSI standards latest revision will be in effect.
B. Materials and Finishes BHMA 1301 Butts and Hinges ANSI A156.1 Locks and Lock Trim ANSI A156.2 Exit Devices ANSI A156.3 Door Controls-Closers ANSI A156.4 Auxiliary Lock & Assoc. Products ANSI A156.5 Architectural Door Trim ANSI A156.6 Template Hinge Dimensions ANSI A156.7 Door Controls-Overhead Holders ANSI A156.8 Mortise Locks and Latches ANSI A156.13 C. Listed Hardware: Hardware which is to be installed in or on fire labeled doors and frames,
Class A or lesser, single or pairs shall be tested and listed by Underwriters Laboratories and/or Warnock Hersey Fire Laboratories Division. Exit devices which are to be used as panic hardware shall be tested and listed in Underwriters Laboratories "Accident Equipment List-Panic Hardware". All listed hardware shall be in compliance with National Fire Protection Association (NFPA) Standard Number 80 UBC 1997, and IBC 2000 and be properly stamped or labeled for easy identification.
1.06 SUBMITTALS A. The door hardware supplier shall, after award of a formal contract, submit to the Architect,
six (6) complete typewritten copies of the proposed Door Hardware Schedule for approval. This schedule shall be prepared using the "Sequence and Format for the Hardware Schedule" as approved and recommended by the Door and Hardware Institute (DHI).
B. When submitting schedules for approval, include six (6) copies of cut sheets on each
hardware item proposed. Index it with the use of number or letters or a combination of both, with the hardware schedule. The index numbers/letters are to be in the right hand column on the same line as the respective manufacturer's numbers shall be indexed even when appearing more than once.
C. Samples: As part of this contract, if requested, the hardware supplier shall provide the
Architect with one sample of each item of door hardware that is to be furnished for this project.
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 4 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
D. Templates: The hardware supplier shall provide necessary templates and/or physical
hardware to all trades requiring them in order that they may cut, reinforce or otherwise prepare their material or product to receive the hardware item. If physical hardware is required by any manufacturer, the hardware supplier shall ship to them such hardware via prepaid freight in sufficient time to prevent any delay in the execution of their work.
E. Submit Material Safety Data Sheets under provisions of Section 01780 for the following
items: 1. Fire doors (insulating material)
1.07 DELIVERY, STORAGE AND HANDLING A. All items of hardware to be delivered to the jobsite shall be completely packaged with all
necessary screws, bolts, miscellaneous parts, instructions and where necessary installation templates for manufacturer's suggested installation. They are to be clearly labeled as to conveniently identify them and their intended location in the building.
B. A representative of the General Contractor shall receive the hardware when delivered at the
jobsite. A dry locked storage space complete with shelving, shall be set aside for the purpose of unpacking, sorting out, checking and storage.
C. Door Hardware shall be delivered to the General Contractor by the hardware supplier.
Direct factory shipments to the jobsite are not acceptable. D. The hardware shall be jointly inventoried by representatives of the General Contractor and
the Hardware Supplier. E. Items damaged in shipment shall be replaced promptly and with proper material without
additional cost to the General Contractor. F. All hardware shall be handled in a manner to minimize marring, scratching or damage. G. Store and handle all materials strictly according to the manufacturer’s instructions. 1.08 WARRANTY Door Closers shall carry a limited warranty against defects in workmanship and operation for a period
of five (5) years from the date of acceptance. The balance of door hardware shall carry a limited warranty against defects in workmanship and operation for a period of one (1) year from date of acceptance. No liability is to be assumed where damage or faulty operation is due to abuse, improper usage, improper installation or failure to exercise normal maintenance.
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 5 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
PART 2 - PRODUCTS 2.01 FINISH OF HARDWARE A. Finish of items shall be as specified under the door hardware sets of this section. B. The finish of items not specially mentioned above nor set forth in the schedule shall be
US26D, unless shown otherwise.
2.02 HINGES AND PIVOTS A. Template Hinges: Provide only template hinges which conform to ANSI A156.7. B. Use concealed bearing or five-knuckle ball bearing hinges, as indicated in the hardware
sets, on heavy doors, doors where high frequency service is expected, doors equipped with door closers, and all labeled doors. (Oil impregnated bearing hinges are not acceptable.)
C. All hinges to be used on exterior doors or doors subject to special atmospheric conditions,
(pool areas, chemical laboratories, sewage disposal plants, etc.) shall be of non-ferrous material, brass, bronze or stainless steel.
D. Hinge pins, except as otherwise indicated, shall be as follows: 1. Steel hinges: Steel pins 2. Non-ferrous hinges: Stainless steel pins 3. Exterior doors: Non-removable pins (NRP) 4. Out-swing corridor doors: Non-removable pins (NRP) 5. Interior doors: Non-rising pins E. Sizes of hinges shall be as follows: Door Thickness Hinge Hinge and Width Height Width 1 3/4" to 36" 4½ 4 or 4½ 1 3/4" over 36" Continuous Hinge F. Number of hinges per door, provided quantities as follows: For doors less than 5 feet high: 1 pair For doors 5 feet to 7 feet 6 inches high: 1 1/2 pair and additional hinge for each additional
2 1/2 feet or fraction thereof. G. Where projection of door trim is such as to prevent degree of opening, the proper hinge
width shall be provided to allow the door to clear the trim. H. Provided above criteria is met, Acceptable and Approved: Ives
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 6 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
I. Continuous Hinges shall be type scheduled with edge protection and as manufactured by one of the following. Coordinate hinge type with Aluminum door supplier.
Ives
2.03 KEYING A. All locks and cylinders shall be factory keyed at the direction of the owner where records
are established and maintained. All cylinders shall be construction Master Keyed. Stamp all keys with “Do Not Duplicate” on one side and key symbol on the other side. A keying meeting is required prior to ordering cylinders for this project. Submit a separate keying submittal for review and approval.
Furnish “3” Cut keys for Each Biting – Balance in Blanks Furnish “20” Building Master Keys Furnish “2” Construction Core Removal Keys Furnish “2” Permanent Core Installation Keys Furnish “2” Construction Keys
. 2.04 MORTISE LOCKS A. Locks shall have all functions available in one size case, manufactured from heavy gauge
steel, minimum thickness of 3/32", complete chrome plated for corrosion resistance and lubricity of parts. Cases are to be closed on all sides to protect internal parts. Locks are to have adjustable, beveled and armored fronts, standard 2 3/4" backset, a full 3/4" throw two-piece mechanical anti-friction latchbolt, a one-piece stainless steel 1" throw deadbolt, and shall be available for a minimum door thickness of 1 3/8". Internal parts shall be heavy gauge steel, zinc dichromate plated for corrosion resistance.
B. All locksets with latchbolts, regardless of trim, shall be listed by Underwriters Laboratories
for A label and less class doors, 4' x 8' single or 8' x 8' pair. C. Lock trim (knob, lever, sectional or escutcheon) shall be throughbolted through the lock case
to assure correct alignment and proper operation. D. Locksets shall conform to Federal Specification FF-H-106C, and be certified as meeting
ANSI A156.13 Series 1000, Grade 1 requirements, ANSI A117.1, Accessibility Code (lever handle trim), and California State Reference Code, 1989 (formerly Title 19, California State Fire Marshall Standard) (lever handle trim).
E. Acceptable and Approved: Schlage L Series
• Schlage AD400 Wireless Lockset
o Self-Contained Wireless Lock: ANSI/BHMA A156.2 Series 4000, Grade 1, wireless bored-
type Mortise, Cylindrical or Exit Trim lock, internal battery powered. Storeroom, Privacy,
Office and Apartment Functions, with key override and also Deadbolt options, Vandal
resistance exterior handle, LED Status indicators. Low Battery Detection and warning, and
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 7 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
ability to program at lock. Complete lockset that includes door position sensor, battery
status, request to exit, interior cover tamper. Keypad, Magnetic Stripe and Multi-technology
readers that read both 125kHz and 13.56 MHz, including MiFare, Desfire EV1 & EV2 and
HID iClass Seos, Mobile Credential enabled to read NFC Mobile Credentials, Standalone
operation, also real-time operation using a Panel Interface Module (PIM) by a Partner
Access Control Network Software. PIM must be provided by Div 28 Contractor. Data
Encryption AES-256-bit, TLS Encryption
2.05 EXIT DEVICES LOW PROFILE PUSH BAR EXIT DEVICES A. The maximum exit device projection shall be a maximum of 3-1/16” when activated. The
exit device bar shall have an average minimum thickness of .201". The pushpad surface shall be constructed of stainless steel; pushpads with plastic or Lexan coatings shall not be acceptable. Nylon bearings and stainless steel springs shall be used for long life and durability. Only torsion or compression springs are acceptable. Extension type springs are not acceptable. All device covers shall be of cast brass, deep drawn steel or stainless steel. Latchbolts shall be of stainless steel and shall have a deadlocking latch for extra security, except at full-glass or two-light glass doors requiring narrow stile device. Mounting screws shall be concealed to deter tampering. All ferrous parts shall be zinc coated to prevent rusting.
B. Single point, one quarter turn hex dogging shall be standard on panic listed devices.
Optional key cylinder dogging shall be available, and furnished if so indicated in the hardware sets, on panic listed devices. Devices with hex key dogging shall be easily field converted to cylinder dogging.
C. All devices shall be listed by Underwriters Laboratories for safety as panic hardware. Fire
rated devices shall be UL listed for A label and lesser class doors, 4' x 8' single and 8' x 8' pair. The model number shall be located on the end cap; devices having the model number located other than on the end cap shall not be acceptable.
D. All exit devices shall have a unitized installation feature and may be cut in the field to size.
Devices shall be closed on all sides with no pinch points. The pushpad shall be designed to prevent pinching of the fingers when depressed.
E. Exit Device trim to be throughbolted. Lever trim to be heavy duty forged escutcheon with
free wheeling levers. F. All exit devices shall conform to Federal Specification FF-H-1820, and be certified as
meeting ANSI A156.3, Grade 1 requirements. G. Acceptable and Approved: Von Duprin 98 Series 2.08 DOOR CLOSERS
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 8 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
A. Closers shall be rack and pinion construction. They shall be non-sized with adjustable spring
power. Closing the door shall be controlled by two valves, one to control closing and one to control latching speed. Closers shall be regularly furnished with fully adjustable backcheck and a backcheck selector valve allowing approximate 70 degree backcheck on both regular and parallel arm closers. All closers shall be mounted with through bolts (SNB). Delayed action shall be available. Valves shall be concealed against unauthorized adjustment and be non-critical needle valve type. All closers shall be provided and installed with all necessary brackets, spacers, plates as required. Furnish and install with manufacture recommended screws. All screws must be installed in all parts, brackets, spacers, and plates.
B. Closers shall be certified as meeting the ANSI A156.4, Grade 1 requirements and be listed
by Underwriters Laboratories for all classes of labeled doors. C. Door Closers shall be furnished on all labeled doors. D. Acceptable and Approved: LCN 4040XP
2.09 OVERHEAD STOPS AND HOLDERS
A. Furnish overhead stops or holders of the weight, functions and materials indicated in the hardware sets. Overhead stops shall only be used when no other means of stopping door.
B. Overhead stops or holders shall be manufactured entirely of metallic components. Units
containing plastic, nylon, or similar materials are not acceptable. C. Acceptable and Approved: Glynn Johnson 2.10 TRIM/KICK PLATES/DOOR STOPS A. All door protection plates to be manufactured of .050” stainless steel. Protection plates to
be furnished 2” less than door width on single doors and 1” less than door width on pairs of doors.
B. Wall mounted door stops shall be provided where door leaves will strike a wall at the end of
their opening cycle. If other conditions exist, furnish floor stops, or, if indicated in the hardware sets, overhead stops.
C. Acceptable and Approved: Ives
2.11 WEATHERSTRIP/THRESHOLDS/SMOKE SEALS
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 9 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
A. Provide weatherstrip, thresholds, and/or sound seals for each opening as scheduled. Review Sill detail on Architectural drawings and furnish threshold type required. Brush type sweep only.
B. Provide smoke seal (including meeting stile seal for door pairs) for all fire rated doors. All
smoke seal and astragals shall be listed by either Underwriters Laboratory or Warnock-Hersey as Category “H” – Smoke and Draft Control Gasket under the testing protocols of UBC Standard 7-2 – 1997, Part 2 and/or UL1784. All smoke seal and astragals shall, additionally, comply with the door manufacturer’s listing under the same protocols.
C. Acceptable and Approved: Zero
PART 3 - EXECUTION 3.01 INSTALLATION A. Mount hardware units at heights indicated in "Recommended Locations for Builders
Hardware" for (Standard Steel Doors and Frames) by the Door and Hardware Institute (DHI), except if otherwise specifically indicated or to comply with requirements of governing regulations, requirements for the handicapped, or if otherwise directed by the Architect.
B. All hardware shall be installed by a tradesman skilled in the application of commercial grade
hardware. C. Install each hardware item in compliance with the manufacturer's instructions and
recommendations. Securely fasten all parts to be attached. Fit faces of mortise parts snug and flush. Make sure all operating parts move freely and smoothly without binding, sticking or excessive clearance. Wherever cutting and fitting is required to install hardware onto or into surfaces which are later to be painted or finished in another way, the hardware shall be removed and stored prior to the painting or finishing. Items shall then be reinstalled only when the finished have been completed on the surface to which the hardware is to be applied.
D. At exterior doors and elsewhere as indicated, set thresholds in a bed of sealant as specified
in Section 07900 to completely fill concealed voids and excluded moisture from every source. Do not plug drain hole or block weeps. Remove excess sealant.
E. After installation, representative templates, instruction sheets and installation details shall
be placed in a file folder to be turned over to the Owner when building is accepted. Included shall be at least five (5) each of any special adjusting and/or installation tools furnished with the hardware by the manufacturers.
PART 4 - SCHEDULES 4.01 HARDWARE SETS
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 10 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
62348 OPT0235277 Version 3
HARDWARE GROUP NO. 001
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SFIC MORTISE CYL. 80-132 W/KEYED CONST. CORE 626 SCH
1 NOTE HARDWARE BY DOOR MANUFACTURER
UNK
HARDWARE GROUP NO. 003
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
1 EA CASED OPEN CASED OPENING
HARDWARE GROUP NO. 004
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
1 NOTE HARDWARE BY DOOR MANUFACTURER
UNK
HARDWARE GROUP NO. 103
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
3 EA HINGE 5BB1 4.5 X 4.5 (HW @ 3'6" & LGR) 652 IVE
1 EA OFFICE/ENTRY LOCK L9050HD 03A L583-363 626 SCH
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA FLOOR STOP FS436 W/RISER TO SUIT CONDITIONS
626 IVE
1 EA GASKETING 188S (@ RATED OR USE SILENCERS)
BK ZER
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 11 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
HARDWARE GROUP NO. 200C
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
6 EA HINGE 5BB1 4.5 X 4.5 (HW @ 3'6" & LGR) 652 IVE
1 SET AUTO FLUSH BOLT FB31P/FB41P AS REQ 630 IVE
1 EA DUST PROOF STRIKE DP2 626 IVE
1 EA STOREROOM LOCK L9080HD 03A 626 SCH
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA COORDINATOR COR X FL X MB X HW PREPS X LENGTH AS REQUIRED
628 IVE
2 EA SURFACE CLOSER 4040XP SCUSH TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 EA GASKETING 188S (@ RATED OR USE SILENCERS)
BK ZER
HARDWARE GROUP NO. 201
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
3 EA HINGE 5BB1 4.5 X 4.5 (HW @ 3'6" & LGR) 652 IVE
1 EA STOREROOM LOCK L9080HD 03A 626 SCH
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SURFACE CLOSER 4040XP REG OR PA TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 EA KICK PLATE 8400 10" X 2" LDW B-CS 630 IVE
1 EA FLOOR STOP FS436 W/RISER TO SUIT CONDITIONS
626 IVE
1 EA GASKETING 188S (@ RATED OR USE SILENCERS)
BK ZER
HARDWARE GROUP NO. 201C
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
3 EA HINGE 5BB1 4.5 X 4.5 (HW @ 3'6" & LGR) 652 IVE
1 EA STOREROOM LOCK L9080HD 03A 626 SCH
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SURFACE CLOSER 4040XP SCUSH TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 EA KICK PLATE 8400 10" X 2" LDW B-CS 630 IVE
1 EA GASKETING 188S (@ RATED OR USE SILENCERS)
BK ZER
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 12 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
HARDWARE GROUP NO. 212F
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
6 EA HINGE 5BB1 4.5 X 4.5 (HW @ 3'6" & LGR) 652 IVE
2 EA MANUAL FLUSH BOLT FB458 626 IVE
1 EA DUST PROOF STRIKE DP2 626 IVE
1 EA STOREROOM LOCK L9080HD 03A 626 SCH
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
2 EA FLOOR STOP FS436 W/RISER TO SUIT CONDITIONS
626 IVE
1 EA GASKETING 188S (@ RATED OR USE SILENCERS)
BK ZER
HARDWARE GROUP NO. 341
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
3 EA HINGE 5BB1 4.5 X 4.5 (HW @ 3'6" & LGR) 652 IVE
1 EA PRIVACY W/DB & IND L9496HD 03A L583-363 626 SCH
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SURFACE CLOSER 4040XP REG OR PA TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 EA KICK PLATE 8400 10" X 2" LDW B-CS 630 IVE
1 EA FLOOR STOP FS436 W/RISER TO SUIT CONDITIONS
626 IVE
1 EA GASKETING 188S (@ RATED OR USE SILENCERS)
BK ZER
HARDWARE GROUP NO. 341C
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
3 EA HINGE 5BB1 4.5 X 4.5 (HW @ 3'6" & LGR) 652 IVE
1 EA PRIVACY W/DB & IND L9496HD 03A L583-363 626 SCH
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SURFACE CLOSER 4040XP SCUSH TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 EA KICK PLATE 8400 10" X 2" LDW B-CS 630 IVE
1 EA GASKETING 188S (@ RATED OR USE SILENCERS)
BK ZER
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 13 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
HARDWARE GROUP NO. 491
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
3 EA HINGE 5BB1 4.5 X 4.5 (HW @ 3'6" & LGR) 652 IVE
EA COOL-DOWN PUSH/PULL LATCH - REVERSE LATCH
1591A 626 TRM
1 EA SURFACE CLOSER 4040XP REG OR PA TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 EA KICK PLATE 8400 10" X 2" LDW B-CS 630 IVE
1 EA FLOOR STOP FS436 W/RISER TO SUIT CONDITIONS
626 IVE
1 EA GASKETING 188S (@ RATED OR USE SILENCERS)
BK ZER
HARDWARE GROUP NO. 501
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
3 EA HINGE 5BB1 4.5 X 4.5 (HW @ 3'6" & LGR) 652 IVE
1 EA CLASSROOM LOCK L9070HD 03A 626 SCH
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SURFACE CLOSER 4040XP REG OR PA TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 EA KICK PLATE 8400 10" X 2" LDW B-CS 630 IVE
1 EA FLOOR STOP FS436 W/RISER TO SUIT CONDITIONS
626 IVE
1 EA GASKETING 188S (@ RATED OR USE SILENCERS)
BK ZER
HARDWARE GROUP NO. 501C
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
3 EA HINGE 5BB1 4.5 X 4.5 (HW @ 3'6" & LGR) 652 IVE
1 EA CLASSROOM LOCK L9070HD 03A 626 SCH
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SURFACE CLOSER 4040XP SCUSH TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 EA KICK PLATE 8400 10" X 2" LDW B-CS 630 IVE
1 EA GASKETING 188S (@ RATED OR USE SILENCERS)
BK ZER
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 14 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
HARDWARE GROUP NO. 501H
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
3 EA HINGE 5BB1 4.5 X 4.5 (HW @ 3'6" & LGR) 652 IVE
1 EA CLASSROOM LOCK L9070HD 03A 626 SCH
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SURFACE CLOSER 4040XP REG OR PA TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 EA KICK PLATE 8400 10" X 2" LDW B-CS 630 IVE
1 EA FLOOR STOP/HOLDER FS40 626 IVE
1 EA GASKETING 188S (@ RATED OR USE SILENCERS)
BK ZER
HARDWARE GROUP NO. 503
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
3 EA HINGE 5BB1 4.5 X 4.5 (HW @ 3'6" & LGR) 652 IVE
1 EA CLASSROOM LOCK L9070HD 03A 626 SCH
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA FLOOR STOP FS436 W/RISER TO SUIT CONDITIONS
626 IVE
1 EA GASKETING 188S (@ RATED OR USE SILENCERS)
BK ZER
HARDWARE GROUP NO. 700ACH
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
2 EA CONT. HINGE 112HD 628 IVE
1 EA PANIC HARDWARE 9849-L-03-LBL-SNB 626 VON
1 EA PANIC HARDWARE 9849-L-DT-03-LBL-SNB 626 VON
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SFIC RIM CYLINDER 80-159 W/KEYED CONST. CORE 626 SCH
2 EA SURFACE CLOSER 4040XP SHCUSH TBSRT - MOUNT TO SUIT CONDITIONS
689 LCN
1 SEAL SET SEAL BY DOOR/FRAME MANUFACTURER
UNK
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 15 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
HARDWARE GROUP NO. 700ACHM
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
2 EA CONT. HINGE 112HD 628 IVE
1 EA KEYED REMOVABLE MULLION
KR4954-STAB - LENGTH AS REQ 689 VON
1 EA PANIC HARDWARE 98-L-03-SNB 626 VON
1 EA PANIC HARDWARE 98-L-DT-03-SNB 626 VON
2 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SFIC MORTISE CYL. 80-132 W/KEYED CONST. CORE 626 SCH
1 EA SFIC RIM CYLINDER 80-159 W/KEYED CONST. CORE 626 SCH
2 EA SURFACE CLOSER 4040XP SHCUSH TBSRT - MOUNT TO SUIT CONDITIONS
689 LCN
1 SEAL SET SEAL BY DOOR/FRAME MANUFACTURER
UNK
1 EA ASTRAGAL MEETING STILE BY DOOR MANUFACTURER
UNK
HARDWARE GROUP NO. 700C
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
2 EA CONT. HINGE 112HD 628 IVE
1 EA PANIC HARDWARE 9849-L-03-LBL-SNB 626 VON
1 EA PANIC HARDWARE 9849-L-DT-03-LBL-SNB 626 VON
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SFIC RIM CYLINDER 80-159 W/KEYED CONST. CORE 626 SCH
2 EA SURFACE CLOSER 4040XP SCUSH TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
2 EA KICK PLATE 8400 10" X 1" LDW B-CS 630 IVE
1 EA GASKETING 188S (@ RATED OR USE SILENCERS)
BK ZER
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 16 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
HARDWARE GROUP NO. 700CH
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
2 EA CONT. HINGE 112HD 628 IVE
1 EA PANIC HARDWARE 9849-L-03-LBL-SNB 626 VON
1 EA PANIC HARDWARE 9849-L-DT-03-LBL-SNB 626 VON
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SFIC RIM CYLINDER 80-159 W/KEYED CONST. CORE 626 SCH
2 EA SURFACE CLOSER 4040XP SHCUSH TBSRT - MOUNT TO SUIT CONDITIONS
689 LCN
2 EA KICK PLATE 8400 10" X 1" LDW B-CS 630 IVE
1 EA GASKETING 188S (@ RATED OR USE SILENCERS)
BK ZER
HARDWARE GROUP NO. 701
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
1 EA CONT. HINGE 112HD 628 IVE
1 EA PANIC HARDWARE 98-L-03-SNB 626 VON
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SFIC RIM CYLINDER 80-159 W/KEYED CONST. CORE 626 SCH
1 EA SURFACE CLOSER 4040XP REG OR PA TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 EA KICK PLATE 8400 10" X 1" LDW B-CS 630 IVE
1 EA FLOOR STOP FS436 W/RISER TO SUIT CONDITIONS
626 IVE
1 EA GASKETING 188S (@ RATED OR USE SILENCERS)
BK ZER
HARDWARE GROUP NO. 711C
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
1 EA CONT. HINGE 112HD 628 IVE
1 EA PANIC HARDWARE 98-L-NL-03-SNB 626 VON
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SFIC RIM CYLINDER 80-159 W/KEYED CONST. CORE 626 SCH
1 EA SURFACE CLOSER 4040XP SCUSH TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 EA KICK PLATE 8400 10" X 1" LDW B-CS 630 IVE
1 EA GASKETING 188S (@ RATED OR USE SILENCERS)
BK ZER
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 17 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
HARDWARE GROUP NO. 711CR
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
1 EA CONT. HINGE 112HD 628 IVE
1 EA FIRE EXIT HARDWARE 98-L-NL-F-03-SNB 626 VON
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SFIC RIM CYLINDER 80-159 W/KEYED CONST. CORE 626 SCH
1 EA SURFACE CLOSER 4040XP SCUSH TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 EA KICK PLATE 8400 10" X 1" LDW B-CS 630 IVE
1 EA GASKETING 188S (@ RATED OR USE SILENCERS)
BK ZER
HARDWARE GROUP NO. 800AV
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
2 EA CONT. HINGE 112HD 628 IVE
2 EA DUMMY PUSH BAR 330 626 VON
2 EA 90 DEG OFFSET PULL 8190 10" HD 630 IVE
2 EA SURFACE CLOSER 4040XP SCUSH TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 SEAL SET SEAL BY DOOR/FRAME MANUFACTURER
UNK
1 EA ASTRAGAL MEETING STILE BY DOOR MANUFACTURER
UNK
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 18 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
HARDWARE GROUP NO. C201
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
3 EA HINGE 5BB1 4.5 X 4.5 (HW @ 3'6" & LGR) 652 IVE
1 EA POWER TRANSFER EPT10 CON 689 VON
1 EA EU MORTISE LOCK L9092HDEU 03A RX CON 12/24 VDC
626 SCH
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SURFACE CLOSER 4040XP REG OR PA TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 EA KICK PLATE 8400 10" X 2" LDW B-CS 630 IVE
1 EA FLOOR STOP FS436 W/RISER TO SUIT CONDITIONS
626 IVE
1 EA GASKETING 188S (@ RATED OR USE SILENCERS)
BK ZER
1 EA MULTITECH READER MT11 OR MT15 AS REQ BLK SCE
1 EA DOOR CONTACT 679-05 WHT SCE
1 EA POWER SUPPLY POWER SUPPLY BY SECURITY CONTRACTOR
UNK
1 EA POWER SUPPLY POWER SUPPLY FOR CARD READER BY SECURITY CONTRACTOR
UNK
2 EA HARNESS (1-IN DOOR / 1-IN FRAME)
ALLEGION CONNECT TYPE & LENGTH AS REQ
VON
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 19 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
HARDWARE GROUP NO. C201C
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
3 EA HINGE 5BB1 4.5 X 4.5 (HW @ 3'6" & LGR) 652 IVE
1 EA POWER TRANSFER EPT10 CON 689 VON
1 EA EU MORTISE LOCK L9092HDEU 03A RX CON 12/24 VDC
626 SCH
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SURFACE CLOSER 4040XP SCUSH TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 EA KICK PLATE 8400 10" X 2" LDW B-CS 630 IVE
1 EA GASKETING 188S (@ RATED OR USE SILENCERS)
BK ZER
1 EA MULTITECH READER MT11 OR MT15 AS REQ BLK SCE
1 EA DOOR CONTACT 679-05 WHT SCE
1 EA POWER SUPPLY POWER SUPPLY BY SECURITY CONTRACTOR
UNK
1 EA POWER SUPPLY POWER SUPPLY FOR CARD READER BY SECURITY CONTRACTOR
UNK
2 EA HARNESS (1-IN DOOR / 1-IN FRAME)
ALLEGION CONNECT TYPE & LENGTH AS REQ
VON
HARDWARE GROUP NO. C341
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
3 EA HINGE 5BB1 4.5 X 4.5 (HW @ 3'6" & LGR) 652 IVE
1 EA ELEC PRIVACY LOCK AD-400-MS-40-SI-TLR-B 4AA BATTERY - AS SPECIFIED IN DIVISION 28
626 SCE
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SURFACE CLOSER 4040XP REG OR PA TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 EA KICK PLATE 8400 10" X 2" LDW B-CS 630 IVE
1 EA FLOOR STOP FS436 W/RISER TO SUIT CONDITIONS
626 IVE
1 EA GASKETING 188S (@ RATED OR USE SILENCERS)
BK ZER
1 EA PIM PROVIDE PIM 400-485 AS REQ UNK
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 20 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
HARDWARE GROUP NO. C341C
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
3 EA HINGE 5BB1 4.5 X 4.5 (HW @ 3'6" & LGR) 652 IVE
1 EA ELEC PRIVACY LOCK AD-400-MS-40-SI-TLR-B 4AA BATTERY - AS SPECIFIED IN DIVISION 28
626 SCE
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SURFACE CLOSER 4040XP SCUSH TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 EA KICK PLATE 8400 10" X 2" LDW B-CS 630 IVE
1 EA GASKETING 188S (@ RATED OR USE SILENCERS)
BK ZER
1 EA PIM PROVIDE PIM 400-485 AS REQ UNK
HARDWARE GROUP NO. C711
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
1 EA CONT. HINGE 112HD/224HD X EPT PREP - TYPE AS REQ
628 IVE
1 EA POWER TRANSFER EPT10 CON 689 VON
1 EA ELEC PANIC HARDWARE RX-QEL-98-L-NL-03-CON-SNB 24 VDC
626 VON
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SFIC RIM CYLINDER 80-159 W/KEYED CONST. CORE 626 SCH
1 EA SURFACE CLOSER 4040XP REG OR PA TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 EA KICK PLATE 8400 10" X 2" LDW B-CS 630 IVE
1 EA FLOOR STOP FS436 W/RISER TO SUIT CONDITIONS
626 IVE
1 EA GASKETING 188S (@ RATED OR USE SILENCERS)
BK ZER
1 EA MULTITECH READER MT11 OR MT15 AS REQ BLK SCE
1 EA DOOR CONTACT 679-05 WHT SCE
1 EA POWER SUPPLY POWER SUPPLY FOR CARD READER BY SECURITY CONTRACTOR
UNK
1 EA POWER SUPPLY PS902 900-2RS LGR SCE
2 EA HARNESS (1-IN DOOR / 1-IN FRAME)
ALLEGION CONNECT TYPE & LENGTH AS REQ
VON
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 21 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
HARDWARE GROUP NO. C714AM-1
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
2 EA CONT. HINGE 112HD/224HD X EPT PREP - TYPE AS REQ
628 IVE
2 EA POWER TRANSFER EPT10 CON 689 VON
1 EA KEYED REMOVABLE MULLION
KR4954-STAB - LENGTH AS REQ 689 VON
1 EA ELEC PANIC HARDWARE RX-98-L-DT-03-CON-SNB 626 VON
1 EA ELEC PANIC HARDWARE RX-QEL-98-L-NL-03-CON-SNB 24 VDC
626 VON
2 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SFIC MORTISE CYL. 80-132 W/KEYED CONST. CORE 626 SCH
1 EA SFIC RIM CYLINDER 80-159 W/KEYED CONST. CORE 626 SCH
2 EA SURFACE CLOSER 4040XP SCUSH TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 SEAL SET SEAL BY DOOR/FRAME MANUFACTURER
UNK
1 EA ASTRAGAL MEETING STILE BY DOOR MANUFACTURER
UNK
2 EA DOOR SWEEP 39A LENGTH AS REQ A ZER
1 EA THRESHOLD 65A-223 LENGTH AS REQ A ZER
1 EA MULTITECH READER MT11 OR MT15 AS REQ BLK SCE
2 EA DOOR CONTACT 679-05 WHT SCE
1 EA POWER SUPPLY POWER SUPPLY FOR CARD READER BY SECURITY CONTRACTOR
UNK
1 EA POWER SUPPLY PS902 900-2RS LGR SCE
2 EA HARNESS (1-IN DOOR / 1-IN FRAME)
ALLEGION CONNECT TYPE & LENGTH AS REQ
VON
2 EA HARNESS (1-IN DOOR / 1-IN FRAME)
ALLEGION CONNECT TYPE & LENGTH AS REQ
VON
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 22 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
HARDWARE GROUP NO. C715A
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
1 EA CONT. HINGE 112HD/224HD X EPT PREP - TYPE AS REQ
628 IVE
1 EA POWER TRANSFER EPT10 CON 689 VON
1 EA ELEC PANIC HARDWARE RX-QEL-98-L-NL-03-CON 24 VDC 626 VON
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SFIC RIM CYLINDER 80-159 W/KEYED CONST. CORE 626 SCH
1 EA SURFACE CLOSER 4040XP SCUSH TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 SEAL SET SEAL BY DOOR/FRAME MANUFACTURER
UNK
1 EA DOOR SWEEP 39A LENGTH AS REQ A ZER
1 EA THRESHOLD 65A-223 LENGTH AS REQ A ZER
1 EA MULTITECH READER MT11 OR MT15 AS REQ BLK SCE
1 EA DOOR CONTACT 679-05 WHT SCE
1 EA POWER SUPPLY POWER SUPPLY FOR CARD READER BY SECURITY CONTRACTOR
UNK
1 EA POWER SUPPLY PS902 900-2RS LGR SCE
2 EA HARNESS (1-IN DOOR / 1-IN FRAME)
ALLEGION CONNECT TYPE & LENGTH AS REQ
VON
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 23 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
HARDWARE GROUP NO. C715AIS
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
1 EA CONT. HINGE 112HD/224HD X EPT PREP - TYPE AS REQ
628 IVE
1 EA POWER TRANSFER EPT10 CON 689 VON
1 EA ELEC PANIC HARDWARE RX-QEL-98-L-NL-03-WH-CON 24 VDC
626 VON
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SFIC RIM CYLINDER 80-159 W/KEYED CONST. CORE 626 SCH
1 EA OH STOP 100S SERIES X SIZE & MOUNTING AS REQ
630 GLY
1 EA SURFACE CLOSER 4040XP REG OR PA TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 SEAL SET SEAL BY DOOR/FRAME MANUFACTURER
UNK
1 EA DOOR SWEEP 39A LENGTH AS REQ A ZER
1 EA THRESHOLD 65A-223 LENGTH AS REQ A ZER
1 EA MULTITECH READER MT11 OR MT15 AS REQ BLK SCE
1 EA DOOR CONTACT 679-05 WHT SCE
1 EA POWER SUPPLY POWER SUPPLY FOR CARD READER BY SECURITY CONTRACTOR
UNK
1 EA POWER SUPPLY PS902 900-2RS LGR SCE
2 EA HARNESS (1-IN DOOR / 1-IN FRAME)
ALLEGION CONNECT TYPE & LENGTH AS REQ
VON
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 24 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
HARDWARE GROUP NO. C715P
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
1 EA CONT. HINGE 112HD/224HD X EPT PREP - TYPE AS REQ
628 IVE
1 EA POWER TRANSFER EPT10 CON 689 VON
1 EA ELEC PANIC HARDWARE RX-QEL-98-L-NL-03-CON 24 VDC 626 VON
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SFIC RIM CYLINDER 80-159 W/KEYED CONST. CORE 626 SCH
1 EA SURFACE CLOSER 4040XP SCUSH TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 EA KICK PLATE 8400 10" X 2" LDW B-CS 630 IVE
1 EA RAIN DRIP 142AA + 4" OVER DOOR WIDTH AA ZER
1 EA GASKETING 328 X (HEAD & JAMBS) AA ZER
1 EA DOOR SWEEP 39A LENGTH AS REQ A ZER
1 EA THRESHOLD 65A-223 LENGTH AS REQ A ZER
2 EA VIEWER 698 MOUNT 1 @ 46" AFF & 1 @ 60" AFF
626 IVE
1 EA MULTITECH READER MT11 OR MT15 AS REQ BLK SCE
1 EA DOOR CONTACT 679-05 WHT SCE
1 EA POWER SUPPLY POWER SUPPLY FOR CARD READER BY SECURITY CONTRACTOR
UNK
1 EA POWER SUPPLY PS902 900-2RS LGR SCE
2 EA HARNESS (1-IN DOOR / 1-IN FRAME)
ALLEGION CONNECT TYPE & LENGTH AS REQ
VON
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 25 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
HARDWARE GROUP NO. C718R
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
2 EA CONT. HINGE 112HD/224HD X EPT PREP - TYPE AS REQ
628 IVE
2 EA POWER TRANSFER EPT10 CON 689 VON
2 EA ELEC FIRE EXIT HARDWARE
RX-QEL-9849-L-NL-F-03-LBL-CON 24 VDC
643E VON
3 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SFIC MORTISE CYL. 80-132 W/KEYED CONST. CORE 626 SCH
2 EA SFIC RIM CYLINDER 80-159 W/KEYED CONST. CORE 626 SCH
2 EA SURFACE CLOSER 4040XP REG OR PA TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
2 EA KICK PLATE 8400 10" X 1" LDW B-CS 630 IVE
2 EA FIRE/LIFE WALL MAG SEM7850 689 LCN
1 EA GASKETING 328 X (HEAD & JAMBS) AA ZER
2 EA MEETING STILE 328AA-S AA ZER
2 EA DOOR SWEEP 39A LENGTH AS REQ A ZER
1 EA THRESHOLD 65A-223 LENGTH AS REQ A ZER
1 EA MULTITECH READER MT11 OR MT15 AS REQ BLK SCE
2 EA DOOR CONTACT 679-05 WHT SCE
1 EA POWER SUPPLY POWER SUPPLY FOR CARD READER BY SECURITY CONTRACTOR
UNK
1 EA POWER SUPPLY PS902 900-2RS LGR SCE
2 EA HARNESS (1-IN DOOR / 1-IN FRAME)
ALLEGION CONNECT TYPE & LENGTH AS REQ
VON
2 EA HARNESS (1-IN DOOR / 1-IN FRAME)
ALLEGION CONNECT TYPE & LENGTH AS REQ
VON
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 26 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
HARDWARE GROUP NO. CR201AC
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
3 EA HINGE 5BB1 4.5 X 4.5 (HW @ 3'6" & LGR) 652 IVE
1 EA POWER TRANSFER EPT10 CON 689 VON
1 EA EU MORTISE LOCK L9092HDEU 03A RX CON 12/24 VDC
626 SCH
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SURFACE CLOSER 4040XP SCUSH TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 SEAL SET SEAL BY DOOR/FRAME MANUFACTURER
UNK
1 EA MULTITECH READER MT11 OR MT15 AS REQ BLK SCE
1 EA DESK MOUNT BUTTON 660-PB 628 SCE
1 EA DOOR CONTACT 679-05 WHT SCE
1 EA POWER SUPPLY POWER SUPPLY BY SECURITY CONTRACTOR
UNK
1 EA POWER SUPPLY POWER SUPPLY FOR CARD READER BY SECURITY CONTRACTOR
UNK
2 EA HARNESS (1-IN DOOR / 1-IN FRAME)
ALLEGION CONNECT TYPE & LENGTH AS REQ
VON
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 27 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
HARDWARE GROUP NO. CR714AM-1
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
2 EA CONT. HINGE 112HD/224HD X EPT PREP - TYPE AS REQ
628 IVE
2 EA POWER TRANSFER EPT10 CON 689 VON
1 EA KEYED REMOVABLE MULLION
KR4954-STAB - LENGTH AS REQ 689 VON
1 EA ELEC PANIC HARDWARE RX-98-L-DT-03-CON-SNB 626 VON
1 EA ELEC PANIC HARDWARE RX-QEL-98-L-NL-03-CON-SNB 24 VDC
626 VON
2 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SFIC MORTISE CYL. 80-132 W/KEYED CONST. CORE 626 SCH
1 EA SFIC RIM CYLINDER 80-159 W/KEYED CONST. CORE 626 SCH
2 EA SURFACE CLOSER 4040XP SCUSH TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 SEAL SET SEAL BY DOOR/FRAME MANUFACTURER
UNK
1 EA ASTRAGAL MEETING STILE BY DOOR MANUFACTURER
UNK
2 EA DOOR SWEEP 39A LENGTH AS REQ A ZER
1 EA THRESHOLD 65A-223 LENGTH AS REQ A ZER
1 EA MULTITECH READER MT11 OR MT15 AS REQ BLK SCE
1 EA DESK MOUNT BUTTON 660-PB 628 SCE
2 EA DOOR CONTACT 679-05 WHT SCE
1 EA POWER SUPPLY POWER SUPPLY FOR CARD READER BY SECURITY CONTRACTOR
UNK
1 EA POWER SUPPLY PS902 900-2RS LGR SCE
2 EA HARNESS (1-IN DOOR / 1-IN FRAME)
ALLEGION CONNECT TYPE & LENGTH AS REQ
VON
2 EA HARNESS (1-IN DOOR / 1-IN FRAME)
ALLEGION CONNECT TYPE & LENGTH AS REQ
VON
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 28 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
HARDWARE GROUP NO. D205
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
1 EA CONT. HINGE 112HD 628 IVE
1 EA STOREROOM LOCK L9080HD 03A 626 SCH
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SURFACE CLOSER 4040XP SCUSH TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 EA KICK PLATE 8400 10" X 2" LDW B-CS 630 IVE
1 EA RAIN DRIP 142AA + 4" OVER DOOR WIDTH AA ZER
1 EA GASKETING 328 X (HEAD & JAMBS) AA ZER
1 EA DOOR SWEEP 39A LENGTH AS REQ A ZER
1 EA THRESHOLD 65A-223 LENGTH AS REQ A ZER
1 EA DOOR CONTACT 679-05 WHT SCE
HARDWARE GROUP NO. D715
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
1 EA CONT. HINGE 112HD 628 IVE
1 EA PANIC HARDWARE 98-L-NL-03-SNB 626 VON
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SFIC RIM CYLINDER 80-159 W/KEYED CONST. CORE 626 SCH
1 EA SURFACE CLOSER 4040XP SCUSH TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 EA KICK PLATE 8400 10" X 2" LDW B-CS 630 IVE
1 EA RAIN DRIP 142AA + 4" OVER DOOR WIDTH AA ZER
1 EA GASKETING 328 X (HEAD & JAMBS) AA ZER
1 EA DOOR SWEEP 39A LENGTH AS REQ A ZER
1 EA THRESHOLD 65A-223 LENGTH AS REQ A ZER
1 EA DOOR CONTACT 679-05 WHT SCE
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 29 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
HARDWARE GROUP NO. D800AV
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
2 EA CONT. HINGE 112HD 628 IVE
2 EA DUMMY PUSH BAR 330 626 VON
2 EA 90 DEG OFFSET PULL 8190 10" HD 630 IVE
2 EA SURFACE CLOSER 4040XP SCUSH TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 SEAL SET SEAL BY DOOR/FRAME MANUFACTURER
UNK
1 EA ASTRAGAL MEETING STILE BY DOOR MANUFACTURER
UNK
2 EA DOOR CONTACT 679-05 WHT SCE
HARDWARE GROUP NO. D801AV
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
1 EA CONT. HINGE 112HD 628 IVE
1 EA DUMMY PUSH BAR 330 626 VON
1 EA 90 DEG OFFSET PULL 8190 10" HD 630 IVE
1 EA SURFACE CLOSER 4040XP SCUSH TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 SEAL SET SEAL BY DOOR/FRAME MANUFACTURER
UNK
1 EA DOOR CONTACT 679-05 WHT SCE
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 30 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
HARDWARE GROUP NO. DE710ACM
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
2 EA CONT. HINGE 112HD/224HD X EPT PREP - TYPE AS REQ
628 IVE
2 EA POWER TRANSFER EPT10 CON 689 VON
1 EA KEYED REMOVABLE MULLION
KR4954-STAB - LENGTH AS REQ 689 VON
1 EA ELEC PANIC HARDWARE RX-98-L-DT-03-CON-SNB 626 VON
1 EA ELEC PANIC HARDWARE RX-98-L-NL-03-CON-SNB 626 VON
2 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SFIC MORTISE CYL. 80-132 W/KEYED CONST. CORE 626 SCH
1 EA SFIC RIM CYLINDER 80-159 W/KEYED CONST. CORE 626 SCH
2 EA SURFACE CLOSER 4040XP SCUSH TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 SEAL SET SEAL BY DOOR/FRAME MANUFACTURER
UNK
1 EA ASTRAGAL MEETING STILE BY DOOR MANUFACTURER
UNK
2 EA DOOR CONTACT 679-05 WHT SCE
1 EA POWER SUPPLY PS902 900-2RS LGR SCE
2 EA HARNESS (1-IN DOOR / 1-IN FRAME)
ALLEGION CONNECT TYPE & LENGTH AS REQ
VON
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 31 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
HARDWARE GROUP NO. DE714AM
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
2 EA CONT. HINGE 112HD/224HD X EPT PREP - TYPE AS REQ
628 IVE
2 EA POWER TRANSFER EPT10 CON 689 VON
1 EA KEYED REMOVABLE MULLION
KR4954-STAB - LENGTH AS REQ 689 VON
1 EA ELEC PANIC HARDWARE RX-98-L-DT-03-CON-SNB 626 VON
1 EA ELEC PANIC HARDWARE RX-98-L-NL-03-CON-SNB 626 VON
2 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SFIC MORTISE CYL. 80-132 W/KEYED CONST. CORE 626 SCH
1 EA SFIC RIM CYLINDER 80-159 W/KEYED CONST. CORE 626 SCH
2 EA SURFACE CLOSER 4040XP SCUSH TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 SEAL SET SEAL BY DOOR/FRAME MANUFACTURER
UNK
1 EA ASTRAGAL MEETING STILE BY DOOR MANUFACTURER
UNK
2 EA DOOR SWEEP 39A LENGTH AS REQ A ZER
1 EA THRESHOLD 65A-223 LENGTH AS REQ A ZER
2 EA DOOR CONTACT 679-05 WHT SCE
1 EA POWER SUPPLY PS902 900-2RS LGR SCE
2 EA HARNESS (1-IN DOOR / 1-IN FRAME)
ALLEGION CONNECT TYPE & LENGTH AS REQ
VON
HARDWARE GROUP NO. W700C
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
2 EA CONT. HINGE 112HD 628 IVE
1 EA FIRE EXIT HARDWARE WS-9827-L-DT-F-03 626 VON
1 EA FIRE EXIT HARDWARE WS-9827-L-F-03 626 VON
2 EA ROD AND LATCH GUARD WS-LGO-3 630 VON
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SFIC RIM CYLINDER 80-159 W/KEYED CONST. CORE 626 SCH
2 EA SURFACE CLOSER 4040XP SCUSH TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 EA GASKETING 188S (@ RATED OR USE SILENCERS)
BK ZER
1 EA THRESHOLD 656A-223 A ZER
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 32 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
HARDWARE GROUP NO. W708
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
2 EA CONT. HINGE 112HD 628 IVE
1 EA FIRE EXIT HARDWARE WS-9827-L-DT-F-03 626 VON
1 EA FIRE EXIT HARDWARE WS-9827-L-F-03 626 VON
2 EA ROD AND LATCH GUARD WS-LGO-3 630 VON
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SFIC RIM CYLINDER 80-159 W/KEYED CONST. CORE 626 SCH
2 EA SURFACE CLOSER 4040XP EDA TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
2 EA FIRE/LIFE WALL MAG SEM7850 689 LCN
1 EA GASKETING 188S (@ RATED OR USE SILENCERS)
BK ZER
1 EA THRESHOLD 656A-223 A ZER
HARDWARE GROUP NO. WD205I
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
1 EA CONT. HINGE 112HD 628 IVE
1 EA MULT PT STOREROOM LM9380HD 03A 626 SCH
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SURFACE CLOSER 4040XP REG OR PA TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 EA KICK PLATE 8400 10" X 2" LDW B-CS 630 IVE
1 EA FLOOR STOP FS436 W/RISER TO SUIT CONDITIONS
626 IVE
1 EA RAIN DRIP 142AA + 4" OVER DOOR WIDTH AA ZER
1 EA GASKETING 328 X (HEAD & JAMBS) AA ZER
1 EA DOOR SWEEP 39A LENGTH AS REQ A ZER
1 EA THRESHOLD 566A LENGTH AS REQ A ZER
1 EA DOOR CONTACT 679-05 WHT SCE
Forney ISD – New Elementary School Ten North (1824-21-01) Kaufman County, Texas
08 7100 - 33 DOOR HARDWARE
ADDENDUM 3 – 12/14/2021
HARDWARE GROUP NO. WDE714
QTY DESCRIPTION CATALOG NUMBER FINISH MFR
2 EA CONT. HINGE 112HD/224HD X EPT PREP - TYPE AS REQ
628 IVE
2 EA POWER TRANSFER EPT10 CON 689 VON
1 EA ELEC PANIC HARDWARE RX-WS-9827-L-03-CON 626 VON
1 EA ELEC PANIC HARDWARE RX-WS-9827-L-DT-03-CON 626 VON
2 EA ROD AND LATCH GUARD WS-LGO-3 630 VON
1 EA SFIC CORE 80-036 KEYED AS DIRECTED 626 SCH
1 EA SFIC RIM CYLINDER 80-159 W/KEYED CONST. CORE 626 SCH
2 EA SURFACE CLOSER 4040XP SCUSH TBSRT X MTG BRKT, SPACER & PLATE AS REQ
689 LCN
1 EA RAIN DRIP 142AA + 4" OVER DOOR WIDTH AA ZER
1 EA GASKETING 328 X (HEAD & JAMBS) AA ZER
2 EA MEETING STILE 328AA-S AA ZER
2 EA DOOR SWEEP 39A LENGTH AS REQ A ZER
1 EA THRESHOLD 566A LENGTH AS REQ A ZER
2 EA DOOR CONTACT 679-05 WHT SCE
2 EA HARNESS (1-IN DOOR / 1-IN FRAME)
ALLEGION CONNECT TYPE & LENGTH AS REQ
VON
END OF SECTION
Forney ISD New Elementary School Ten North
Project: Forney ISD New Elementary School Ten North
Allegion: OPT0235277
Print Date: 12/14/2021 1
Door# HwSet#
1.01 501H1.02 501H1.03 501H1.04 501H1.07 C201C1.08 201C1.09 711CR1.10 501H1.11 501H1.12 501H1.13 501H1.14 501H1.15 2011.16 C201C1.17 501H1.18 C341C1.19 C3411.20 501H1.21 711C1.22 2011.23 501H1.24 501H1.25 501H1.26 501H1.27 2011.28 2011.34 800AV1.35 C714AM-11.40 700C1.40A 2011.41 C714AM-11.44 800AV1.45 DE714AM1.46 501H1.47 501H1.48 501H1.48A 3411.49 2011.50 501H1.51 501H1.52 501H1.53 501H1.54 501H1.55 501H1.56 501H1.57 C341C
Forney ISD New Elementary School Ten North
Project: Forney ISD New Elementary School Ten North
Allegion: OPT0235277
Print Date: 12/14/2021 2
Door# HwSet#
1.59A 501H1.59B 501H1.60 341C1.62 C341C1.63 501H1.64 501H1.65 501H1.66 501H1.67 501H2.02 711CR2.03 D2052.04 201C2.05 501H2.06 2012.07A C714AM-12.07B DE714AM2.07C 800AV2.07D D800AV2.08 501H2.09A 501C2.09B 5012.10 2012.11 501H2.12 5032.13 C2012.14 2012.15 C715A2.18A CR714AM-12.18B DE714AM2.18C DE710ACM2.18D DE710ACM2.20 700CH2.21 C718R2.22 2012.23 5012.24 C3412.25 C7112.26 C2012.27A 5012.27B 5012.28 3412.29A CR201AC2.29B CR201AC2.29C 7012.30 1032.31 501
Forney ISD New Elementary School Ten North
Project: Forney ISD New Elementary School Ten North
Allegion: OPT0235277
Print Date: 12/14/2021 3
Door# HwSet#
2.32 1032.33A 2012.33B 2012.34 C3412.35 1032.36 2012.37 4912.38 2012.39 1032.40 5032.41 1033.01A C714AM-13.01B 800AV3.04 3413.05 201C3.06 C715P3.07A 501H3.07B 501H3.08 212F3.09 2013.10 1033.11 0033.12 C201C3.13 C201C3.14 201C3.15 D7153.16A 800AV3.16B C714AM-13.17A W7083.17B W700C3.17C WDE7143.18 200C3.19A C201C3.19B WD205I3.20 3413.21 3413.23 3413.24 3413.25 5033.26A 800AV3.26B 800AV3.27A C714AM-13.27B DE714AM3.28 C3413.29 C3413.33 501C
Forney ISD New Elementary School Ten North
Project: Forney ISD New Elementary School Ten North
Allegion: OPT0235277
Print Date: 12/14/2021 4
Door# HwSet#
3.34 200C3.35 200C3.37A C714AM-13.37B 800AV3.38A 700ACH3.38B 700ACH3.39 212F4.01 501H4.02 501H4.03 501H4.04 501H4.05 501H4.06 C201C4.07 2014.08 501H4.09 711CR4.10 2014.11 2014.12 C3414.13 C341C4.14 2014.15 2014.16 501H4.17 501H4.18 501H4.19 501H4.27A D801AV4.27B C715AIS4.28A 700ACHM4.28B C715AIS4.30 501H4.31 501H4.32 501H4.34 501H4.35 2014.36 2014.39 501H4.42 501H4.43 501H4.44 501H4.45 501H4.46 501H5.01 C718RFP4.14 004FP4.35 004OH2.16 001OH3.07 001OH3.11 001