fxuq
TRANSCRIPT
ED34-862 Specifications
FXUQ-MA 383
12
2. Specifications
Ceiling Suspended Cassette Type
Notes:★1 Indoor temp. : 27°CDB, 19.5°CWB / outdoor temp.: 35°CDB / Equivalent piping length: 7.5m, level difference: 0m.★2 Indoor temp. : 27°CDB, 19.0°CWB / outdoor temp.: 35°CDB / Equivalent piping length: 7.5m, level difference: 0m.
3 Capacities are net, including a deduction for cooling (an additional for heating) for indoor fan motor heat.★4 Anechoic chamber conversion value, measured at a point 1.5m downward from the unit center. These values are normally somewhat higher
during actual operation as a result of ambient conditions.5 Refer to page 391 for Fan Motor Input.
ModelIndoor Unit FXUQ71MAV1 FXUQ100MAV1 FXUQ125MAV1
Connection Unit BEVQ71MAVE BEVQ100MAVE BEVQ125MAVE
★1 Cooling Capacity (19.5°CWB)
kcal/h 7,100 10,000 12,500
Btu/h 28,300 39,600 49,500
kW 8.3 11.6 14.5
★2 Cooling Capacity (19.0°CWB) kW 8.0 11.2 14.0
Casing Color White (10Y9/0.5) White (10Y9/0.5) White (10Y9/0.5)
Dimensions: (H×W×D) mm 165×895×895 230×895×895 230×895×895
Coil (Cross Fin Coil)
Rows×Stages×Fin Pitch mm 3×6×1.5 3×8×1.5 3×8×1.5
Face Area m² 0.265 0.353 0.353
Fan
Model QTS48A10M QTS50B15M QTS50B15M
Type Turbo Fan Turbo Fan Turbo Fan
Motor Output × Number of Units W 45×1 90×1 90×1
Air Flow Rate (H/L)m³/min 19/14 29/21 32/23
cfm 671/494 1,024/741 1,130/812
Drive Direct Drive Direct Drive Direct Drive
Temperature Control Microprocessor Thermostat forCooling and Heating
Microprocessor Thermostat for Cooling and Heating
Microprocessor Thermostat for Cooling and Heating
Sound Absorbing Thermal Insulation Material Heat Resistant Foamed Polyethylene, Regular Foamed Polyethylene
Heat Resistant Foamed Polyethylene, Regular Foamed Polyethylene
Heat Resistant Foamed Polyethylene, Regular Foamed Polyethylene
Piping Connections
Liquid Pipes mm φ9.5 (Flare Connection) φ9.5 (Flare Connection) φ9.5 (Flare Connection)
Gas Pipes mm φ15.9 (Flare Connection) φ15.9 (Flare Connection) φ15.9 (Flare Connection)
Drain Pipe mm VP20(External Dia. 26 Internal Dia. 20)
VP20(External Dia. 26 Internal Dia. 20)
VP20(External Dia. 26 Internal Dia. 20)
Machine Weight kg 25 31 31
★4 Sound Level (H/L) (230V) dBA 40/35 43/38 44/39
Safety Devices Thermal Protector for Fan Motor Thermal Protector for Fan Motor Thermal Protector for Fan Motor
Standard Accessories
Operation Manual, Installation Manual, Drain Hose, Clamp Metal, Insulation for Fitting, Sealing Pads, Clamps, Screws, Washers, Holding Plate.
Operation Manual, Installation Manual, Drain Hose, Clamp Metal, Insulation for Fitting, Sealing Pads, Clamps, Screws, Washers, Holding Plate.
Operation Manual, Installation Manual, Drain Hose, Clamp Metal, Insulation for Fitting, Sealing Pads, Clamps, Screws, Washers, Holding Plate.
Drawing No. C : 4D045395A
Conversion Formulae
kcal/h=kW×860Btu/h=kW×3412
cfm=m³/min×35.3
Please purchase PDF Split-Merge on www.verypdf.com to remove this watermark.
Specifications ED34-862
384 FXUQ-MA
BEV Units
Connection Example
Model BEVQ71MAVE BEVQ100MAVE BEVQ125MAVE
Power Supply 1 Phase 50Hz 220~240V 1 Phase 50Hz 220~240V 1 Phase 50Hz 220~240V
Casing Galvanized Steel Plate Galvanized Steel Plate Galvanized Steel Plate
Dimensions: (H×W×D) mm 100×350×225 100×350×225 100×350×225
Sound Absorbing Thermal Insulation Material
Flame and Heat Resistant Foamed Polyethylene
Flame and Heat Resistant Foamed Polyethylene
Flame and Heat Resistant Foamed Polyethylene
Piping Connection
Indoor Unit
Liquid Pipes 9.5mm (Flare Connection) 9.5mm (Flare Connection) 9.5mm (Flare Connection)
Gas Pipes 15.9mm (Flare Connection) 15.9mm (Flare Connection) 15.9mm (Flare Connection)
Outdoor Unit
Liquid Pipes 9.5mm (Flare Connection) 9.5mm (Flare Connection) 9.5mm (Flare Connection)
Suction Gas Pipes 15.9mm (Flare Connection) 15.9mm (Flare Connection) 15.9mm (Flare Connection)
Machine Weight (Mass) kg 3.0 3.0 3.5
Standard AccessoriesInstallation manual, Gas piping
connections, Insulation for fitting, Sealing material, Clamps
Installation manual, Gas piping connections, Insulation for fitting,
Sealing material, Clamps
Installation manual, Gas piping connections, Insulation for fitting,
Sealing material, Clamps
Drawing No. 4D045387A 4D045387A 4D045388A
BRC1C62
PowerPowersupplysupply
lineline
TransmissionTransmissionlineline
ControlWiringControlWiring
1. Wiring Work•The connecting line between SkyAir Indoor Unit
– BEV Unit : 3 cores…like a Transmission Line•BEV Unit’s power supply line; Single phase 2 line…like a VRV Indoor unit•BEV Unit – other VRV indoor unit or outdoor unit – : 2 cores…DIII network wiring (super wiring)2. Piping work SkyAir side,Outdoor Unit Side,They are both flare connection.
-When connecting centralized-control device, it is necessary to install an interfaceadaptor for SkyAir series in an indoor unit.
-Distance between indoor unit and –BEV unit must be within 5m.
Consideration matter
Installation pattern / maintenance
Outline figure
Gas pipe (With Thermistor,
Liquid pipe
Insulation pipe cover)
Electric valve drive part
Hanger
PC board
Terminal block
SW.BOX cover
Piping part cover
(Wall surface attachment is also possible)
1. Level installation (It hangs by two hangers) 2. Vertical Installation (Wall Surface Mounted)
Service space*1
*1; Service space for switch box. (Service access panel is required for the bottom side. When there is nothing, 350 or more spaces are required. )*2; For electric valve drive part’s maintenance. (a control box is removed)
Installation space
150 or more
Service space*2100 or more
Gas pipe
Screw fixed(x2 Screws x2 place)
Hanger bolt Liquid pipe
Service access panel (450 x 450 )
Please purchase PDF Split-Merge on www.verypdf.com to remove this watermark.