fs 501 installation

7/27/2019 FS 501 Installation

http://slidepdf.com/reader/full/fs-501-installation 1/7

E-1

FS-501 Finisher

4684-7701-01

INSTALLATION MANUAL Applied Machine:

for Product Code 4038

I. Accessory parts

* This machine doesn’t use the Rail guide A.

No. Name Shape Q’ty

1. Rail guide A

1

2. Rail guide B

1

3. Ground plate

1

4. Rail

1

5. Stabilizing pin

1

6. Magnet plate

1

7. Horizontaltransport unit

1

8. Tray

1

9. Protective

guide

1

4698U044AA

4684U061AB

4684U062AA

4683IXC505DA

4683IXC504DA

4698U047AA

4698U048AA

4684U075AA

4684U070AA

10. Label

1

11. Screws A

(4 × 12 mm)

3

12. Screws B

(4 × 8 mm)

2

13. Installation

Manual1

set

14. Spacer

1

After unpacking, be sure to get rid of the

packaging materials and keep them out of

the reach of children.Putting your head in the wrapper involves

danger of suffocation.

No. Name Shape Q’ty

4684U076AB

4684U072AA

9735U001AA

4980IXC019DA

4583U018AA



E-2

II. Before Installing the Finisher

In order to adjust the height of the machine to the

height of the finisher, the Paper Feed Cabinet PC-

103, or PC-203, or PC-403, or Desk DK-502 must

be installed.

Machine + Paper Feed Cabinet PC-103/PC-203

Machine + Paper Feed Cabinet PC-403

Machine + Desk DK-502

III. Installation procedures

1. Remove protective tape and packing materials

from different parts of the finisher.

4684IXC007DA

4684IXC008DA

4684IXC009DA

Packing

bracket

Note:

Do not remove these parts.

Packing bracket

C4683U006AB

4684U074AA

C4683U008AA

4683U013AA

4643U003AA

Tape



E-3

Note:

• Make sure that the installation site is flat and

level.

• After the Finisher has been set up, avoid mov-

ing it unless it is absolutely necessary.

See “VII.Removing the Rail” of P.E-7 to move it.

After moving it, follow step 13 to 15 of P.E-5 and

step 8 and 9 of P.E-4.

2. Turn off the machine and unplug the power cord

from the power outlet.

3. Remove the Sub tray of the machine.

4. Peel off the seal covering the area where the sta-

bilizing pin and magnet plate will be attached.

5. Attach the stabilizing pin and magnet plate to the

left side of the machine as shown (three screw

A’s furnished with the Finisher).

6. Place the Ground Plate in Rail Guide B.

7. Attach the rail guide B to the left side of the Paper

Feed Cabinet as shown in the illustration (two

screw B’s furnished with the Finisher).

Note:

Fit Rail Guide B in the tab on the lower portion of

the Paper Feed Cabinet.

4684IXC001DA

4684IXC002DB

4684IXC003DB

4684U063AB

4684U064AA



E-4

8. Insert the rail into the Rail Guide B.

9. Protrude the leading edge of the rail out about 60

mm to the right from the right end of the machine.

Note:

• If the rail is pulled out more than necessary, it is

caught by the flat spring fitted to the machine

as it is brought back into the original position.

• When setting it, make sure the rail notch comes

under.

10.Insert the spacer into the rail.

Note:

Slide out the rail to the left and check that it does

not come off the Rail Guide B.

11.Slide the other end of the rail installed in step 8

into the rail guide on the finisher.

Note:

Insert the rail until it snaps into place.

At this time, the finisher should stay attached to

the machine, even if you try to pull it away.

12.Remove protective tape of the horizontal trans-

port unit.

4684U065AA

4684IXC012DA

OK NG

4583U017AB

C4683U011AA

C4683U010AA

C4651U023AB

Tape



E-5

13.Place the horizontal transport unit on the paper

output section of the machine, and make sure

that the plastic guide pin on the bottom of the hor-

izontal transport unit hooks into the bracket on

the finisher.

14.Press the horizontal transport unit up against the

rear side.

Note:

Make sure that the gear on the finisher and that on

the horizontal transport unit are in positive mesh

with each other.

15.Secure the horizontal transport unit with the lock.

IV. Adjusting the Height and Tilt of the Fin-

isher

1. If the finisher gradually tilts toward the machine,

check the following:

• Are the stabilizing pin and the hole in the finisher

at the same height?

• Is the horizontal transport unit not extremely

tilted?

* If the finisher is not at the same height as the

machine, adjust the machine as follows.

2. Slide the finisher away from the machine, and

then remove the lower-front cover of the finisher

(two screws).

3. Lift the finisher’s two caster covers up, and then

pull them off.

C4683U023AA

C4683U014AA

C4683U013AA

4684IXC004DA

4643U021AB

4643U020AA



E-6

4. Without turning the adjusting bolt (lower bolt) on

the caster, loosen the securing bolt (upper bolt),

and then turn the adjusting bolt (lower bolt) as

indicated below to adjust the height of the fin-

isher.

<Two rear casters>

If the stabilizing pin is too high:

Turn the bolt clockwise

If the stabilizing pin is too low:

<Two front casters>

If the magnet plate is too high:

Turn the bolt clockwise

If the magnet plate is too low:

Turn the bolt counterclockwise

5. If the finisher tilts toward the machine, check the

following:

• Are distances a and b equal?

* If a and b are not equal, refer to step 4 above and

turn the adjusting bolt (lower bolt) as indicated to

adjust the tilt of the finisher.

6. After the adjustment is finished, without turning

any of the adjusting bolts (lower bolts), tighten

the four securing bolts (upper bolts).

7. Reinstall the caster cover which has been

removed in step 3.

8. Reinstall the lower-front cover which has been

removed in step 2 (two screws).

V. Connecting the Hookup Cord

1. Connect the hookup cord to the horizontal trans-

port unit and the machine.

2. Secure the hookup cord of the Horizontal Trans-

port Unit using the cord clamp (large) of the fin-

isher.

4643U022AB

Securing bolt

Adjusting

bolt

4684IXC005DA

a

b

4643U029AA

Securing bolt

Adjusting bolt

4684IXC014DA

4684U069AA



E-7

VI. Installing the Tray and Protective Guide

Install the tray and protective guide at the positions

shown in the illustrations.

VII. Removing the Rail1. Pinch together the rail stoppers on the left side of

the finisher to release them.

2. Disconnect the two hookup cords.

3. Remove the horizontal transport unit from the fin-

isher, and then place it on top of the machine.

4. Carefully pull the finisher away from the machine.

5. Slide the rail under the machine, and then

remove it from the right side of the machine.

VIII. Affixing the Labels

Affix the labels to the position shown below.

4643U017AA

4643U024AA

4684IXC015DB

4698U109AA

C4683U018BA

for Machine

for Automatic Doc-

ument Feeder

Label for Machine

Label for Automatic Document Feeder

4684U076AB

fs 501 installation

Documents