framo 80 beam section tp f 80 - · pdf file15framo 80 beam section tp f 80 group: a410...
TRANSCRIPT
15Framo 80
Beam Section TP F 80Group: A410
ApplicationGalvanised hollow-box-section for fabrication of steel frames. Designed for both simple two-dimensional supports and complex volumetric arrangements. Holes designed to receive Self Forming Screw FLS in conjunction with the relevant component.
Technical Data
Mechanical properties shown above take into account perforations.
ApprovalsCE mark (Declaration of performance see www.sikla.com/service/downloads)
Type Weight[kg/m]
Qty.[m]
Partnumber
TP F 80 6.4 6 192539TP F 80/30 4.3 6 113407
Type Section modulus
[cm3 ]
Moment of inertia[cm4 ]
Radius of inertia[cm]
Torsional moment lt
[cm 4 ]
Cross section A
[cm2 ]
TP F 80 Wy: 15.87Wz: 15.87
ly: 63.49lz: 63.49
iy: 2.95iz: 2.95
98.22 7.28
TP F 80/30 Wy: 8.36Wz: 4.03
ly: 33.47lz: 6.05
iy: 2.76iz: 1.17
18.66 4.37
Material: Steel, hcp
Framo 80
Siconnect 15-110/2
015
TP F 80/30
15Framo 80
End Support STA F 80Group: A422
ApplicationPlug-in component designed to create an endplate at the open end of a Beam Section TP F80 or a Cantilever bracket AK F80.
InstallationDepending on the version, following mountings solutions are possible:
Technical Data
ApprovalsCE mark (Declaration of performance see www.sikla.com/service/downloads)MPA tested
Type W[kg]
Quantity[pack]
Partnumber
STA F 80 1.6 1 192856STA F 80-E 1.5 1 192863STA F 80-A 1.7 1 192870
a) With 2x4 Self Forming Screws FLS when used to connect 2 Beam Sections.
b) With 4 Self Forming Screws FLS applied to the octagonal insert and 2 suitable wall anchors/fixings when connected to the building structure.
Type Dimensions of Base plate [mm]
Slots in base plate for
STA F 80 190 x 80 x 8 M10STA F 80-E 165 x 80 x 8 M10STA F 90-A 190 x 80 x 8 M12
Configuration: Base plate welded to octagonal element F 80Material:Plate: Steel, HCPOctagonal element: Steel, HCP
Framo 80
Siconnect 15-110/2
015
STA F 80
STA F 80-E
STA F 80-A
11High Corrosion Protected Products
Channel Connector SK-L HCPGroup: 1853
ApplicationElement for connecting Channels. The multiple bearing of the Channel is to be secured. The Channel Connector should not to be used between the last two bearing points. In combination with Channels > 41/21 the admissible limit has to be respected.
InstallationPosition the Channel Connector on the back of the channel and bolt together the channel ends (through the channel slots) by means of each two Self Forming Screws FLS F 80.
Technical Data
Type For channel Channel heighthmax [mm]
Overall length [mm]
W[kg]
Quantity[pack]
Partnumber
SK-L 41 62 180 0.36 10 198971
Max. adm. limit/ flexion: 300 NmMaterial: Steel S235 JR, HCP
High Corrosion Protected Products
Siconnect 11-110/2
015
16Framo 100
Self Forming Screw FLSGroup: A430
ApplicationThe Self Forming Screw FLS creates its own thread inside the wall of the Framo pilot hole. During the screw-driving operation, the base steel is re-shaped and hardened to form an air-tight seal between the threads of the screw and the surrounding steel, making it exceptionally resistant to vibrational loosening and increasing fastening strength.
Technical Data
ApprovalsMPA tested
Type W[kg]
Quantity[pack]
Partnumber
FLS F 0.03 100 192512
Application Tightening torque[Nm]
System Framo 60Connection to Channels MS 41 35
Material: Steel, HCP
Framo 100
Siconnect 16-110/2
015
2Construction Components
End Clip PV 1-EGroup: E314
ApplicationEdge fastening and assembly block for all typical framed Photovoltaic panels to be used with high loads caused by wind suction. Suits panel thicknesses of 35 - 50 mm for any angle. Bimetal corrosion restistance, by using seal-coating on the support (washer and sleeve). Clamping forces applied at outer edge of panel to prevent undue tensioning of glass.
Scope of deliveryFully assembled unit comprising Speed Nut, Support and Clip.
InstallationInsert Speed Nut into the open channel slot at any position required.Adjust the clip to the panel and tighten it with max. 10 Nm.
Technical Data
Type Panelthickness
[mm]
W[kg]
Quantity[pack]
Partnumber
PV 1-E 35 - 50 0.11 50 199503
adm. shear force 90° to panel surface: 0.5 kN/clipadm. tensile load: 3.2 kN/clipMaterial:Clip: AluminiumScrew: Stainless steel 304Stud bolt, Washer and Speed Nut: HCP
Construction Components
Solar Panel Support System 2-110/2
015
2Construction Components
Middle Clip PV 1-MGroup: E314
ApplicationMiddle fastening and assembly block for all typical framed Photovoltaic panels to be used with high loads caused by wind suction. Suits panel thicknesses (H) of 35 - 50 mm for any angle. Bimetal corrosion resistance, by using seal-coating on the support (washer and sleeve). Clamping forces applied at outer edge of panel to prevent undue tensioning of glass.
Scope of deliveryFully assembled unit comprising Speed Nut, Support and Clip. No loose parts.
InstallationFix Middle Clip into the required position by pressing the Speed Nut into the channel. Slide the Middle Clip along the channel so that it grips onto the existing PV panel already in position. Put the next panel on the frame and tighten the Middle Clip with max 10 Nm.
Technical Data
Type Panelthickness
[mm]
W[kg]
Quantity[pack]
Partnumber
PV 1-M 35 - 50 0.09 50 199510
adm. shear force 90° to panel surface: 1.0 kN/clipadm. tensile load: 3.2 kN/clipMaterial:Clip: AluminiumScrew: Stainless steel 304Stud bolt, Washer and Speed Nut: HCP
Construction Components
Solar Panel Support System 2-110/2
015
2Pressix CC 41 - Assembly System
End Cap ADK 41Group: 1304
ApplicationTo be used for safely and neatly covering the ends of Sikla Channels. Double channels require 2 End Caps.
Technical Data
Type For channel W[kg]
Quantity[pack]
Partnumber
41/21 41/21/1.5 und 41/21/2.5 0.01 100 10103741/31 0.01 100 11047741/41 41/41/1.8 und 41/41/2.5 0.01 100 17768941/45 41/45/3.0 0.01 100 10881241/52 41/52/3.0 0.01 50 17769841/62 41/62/3.0 0.01 50 15320141-75/65 41-75/65/3.0 0.01 50 17770741-75/75 41-75/75/3.0 0.02 50 177716
Material: HD-PE, yellow
Pressix CC 41 - Assembly System
Siconnect 2-110/2
015
15Framo 80
End Cap ADK F 80Group: A430
ApplicationPlastic end cap to close cut ends of Beam Section F80 to meet both visual and health & safety requirements. Standard Cantilever- and Beam Brackets (AK F80 and TKO F80) already include this end cap.
InstallationMallet required.
Technical Data
Type W[kg]
Quantity[pack]
Partnumber
ADK F 80 0.03 25 192674ADK F 80/30 0.02 25 113067
Material: PE, yellow
Framo 80
Siconnect 15-110/2
015
ADK F 80/30
2Construction Components
Channel MS 41 HCPGroup: 1811
ApplicationElement for easily and efficiently pre-assembling crossbars, wall brackets and supporting structures on construction sites or in workshops.
Scope of deliveryAvailable as single or double channels.Double channels are joined together by clinching.
InstallationAll Channels MS 41 hcp are serrated inside and provide numerous combination options with other high corrosion protected system components.
Technical Data
D = Double channel
Approvals
Material: Steel, HCP
TypeW/H/th [mm]
Section modulus[cm3 ]
Moment of inertia[cm4 ]
Radius of gyration[cm]
41/21/2.0 Wy : 0.82Wz : 2.12
ly : 0.92lz : 4.35
iy : 0.76iz : 1.65
41/31/2.0 Wy : 1.60Wz : 2.88
ly : 2.77lz : 5.90
iy : 1.13iz : 1.65
41/41/2.0 Wy : 2.43Wz : 3.65
ly : 5.16lz : 7.48
iy : 1.46iz : 1.75
41/41/2.5 Wy : 2.96Wz : 4.41
ly : 6.19lz : 9.05
iy : 1.43iz : 1.72
41/62/2.5 Wy : 5.54Wz : 6.27
ly : 17.70lz : 12.86
iy : 2.10iz : 1.79
41-75/75/3.0 Wy : 10.31Wz : 11.59
ly : 44.42lz : 43.48
iy : 2.53iz : 2.50
41/21/2.0 D Wy : 2.35Wz : 4.24
ly : 4.93lz : 8.70
iy : 1.24iz : 1.65
41/41/2.5 D Wy : 9.02Wz : 8.82
ly : 36.99lz : 18.10
iy : 2.46iz : 1.72
41-75/75/3.0 D Wy : 30.72Wz : 23.07
ly : 230.40lz : 86.96
iy : 4.07iz : 2.50
TypeW/H/th [mm]
Cross sectionA
[cm2 ]
Distancee
[cm]
Max. point carrying capacity
Fmax [kN]
Max. torsionalmomentMq [Nm]
41/21/2.0 1.61 1.12 4.0 44.541/31/2.0 2.17 1.73 4.0 44.541/41/2.0 2.43 2.12 4.0 44.541/41/2.5 3.05 2.09 6.0 44.541/62/2.5 4.01 3.20 6.0 44.541-75/75/3.0 6.95 4.31 10.0 44.5
41/21/2.0 D 3.21 2.10 4.0 44.541/41/2.5 D 6.09 4.10 6.0 44.541-75/75/3.0 D 13.90 7.50 10.0 44.5
Notice: All values take into account the perforation of the channels. For load charts, see chapter "Pressix CC 41".
Construction Components
Solar Panel Support System 2-110/2
015
41/21/2,0
41/412,5
41-75/75/3.0
* = no RAL quality label
Construction Components
Type Length [m]
Slot pattern Weight[kg/m]
Qty.[m]
Partnumber
41/21/2.0 6 3 1.32 6 19386041/31/2.0 6 3 1.64 6 19889641/41/2.0 6 3 1.97 6 19672441/41/2.5 6 3 2.36 6 16149741/62/2.5 6 3 3.13 6 19952741-75/75/3.0 6 4 5.68 6 174008
41/21/2.0 D * 6 3 2.64 6 19388441/41/2.5 D * 6 3 4.74 6 16674841-75/75/3.0 D * 6 4 11.24 6 173981
Solar Panel Support System 2-2
This product is has obtained the "RAL Gütezeichen Rohrbefestigung" and is subject to external surveillance according to RAL GZ-655.
10/2
015