fortezza™ plus (ftz) - serva-lite · instructions 926000318 fortezza™ plus (ftz) 09/18/2013...
TRANSCRIPT
INSTRUCTIONS
926000318
Fortezza™ Plus (FTZ)
09/18/2013
IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including the following: 1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS 2. Disconnect power before performing work on electrical equipment.3. Use caution when servicing batteries. 4. Equipment should be mounted in locations and at heights where unauthorized personnel will not readily subject it to tampering.5. The use of accessory equipment not recommended by Beghelli Canada Inc., may cause an unsafe condition, and will void the unit’s warranty.6. Do not use this equipment for other than its intended purpose.7. Servicing of this equipment should be performed by qualified service personnel.8. SAVE THESE INSTRUCTIONS!
Chassis GNDLED Board
AC ONLY SIGN
Chassis GND
GREEN Ground
BLACK 120VACRED 347VAC or ORANGE 200-277VAC
WHITE Neutral
LED Board
AC & UNIVERSAL DC SIGN
YELLOW Positive 6 to 24VDC
PURPLE Negative
Emergency SupplyFROM Battery Pack
SELF-POWERED SIGN
Chassis GND24 hoursUnswitched Supply
GREEN Ground
BLACK 105 to 360VAC
WHITE Neutral
LED Board
DUAL UNIVERSAL AC SIGNFrom Generator OREmergency Supply
BROWN 105 to 360VAC
BLUE Neutral
NOTE: Cap unused AC Wire!NOTE: Cap unused AC Wire!
24 hoursUnswitched Supply
GREEN Ground
BLACK 120VACRED 347VAC or ORANGE 200-277VAC
WHITE Neutral
24 hoursUnswitched Supply
Chassis GNDLED Board
NOTE: Cap unused AC Wire!
GREEN Ground
BLACK 120VACRED 347VAC or ORANGE 200-277VAC
WHITE Neutral
24 hoursUnswitched Supply
Ni-CdBattery
Beghelli Canada Inc., 3900 14th Avenue, Markham, ON L3R 4R3 Tel: (905) 948-9500 Fax: (905) 948-8673926000318
09/18/2013
CEILING/END MOUNT INSTALLATION
WALL MOUNT INSTALLATION:
1. Remove torx screws (9) to release clear cover (1). There are 4 O-rings (10) inserted to the clear cover screw holes. Release the stencil (2) from the clear cover (1). Knockout to remove the chevron as necessary from the stencil. Peel off backing paper from the tape on the back of the stencil and carefully position and stick the colored fibre to the stencil.
2. To install canopy kit, knockout on the top (for ceiling mount) or the knockout on the side (for end mount). Position canopy gasket and the canopy (14). Install the cap screws and the washers. Attach canopy nuts and then tighten. Install the liquid tight bushing (12), feed the lead wired through the bushing and tighten to complete the liquid tight seal. Install the canopy mounting base (15) to the octagon box (11) (not supplied). Connect wires per diagram provided. Caution! Failure to insulate unused wire may result in a shock hazard or unsafe condition as well as equipment failure. The mounting base can be rotated for the desired mounting angle. Install the canopy (14) to the mounting base (15) with the supplied screws.
3. Note: When installing the cover, be sure to align the light pipe (5) and LED indicator. 4. Apply power.
SELF-POWERED:1. For models FTZ-SP, plug the battery into the circuit board per (wiring diagram) self-powered sign.
MAINTENANCE1. Clean face(s) on a regular basis.
NOTE: The servicing of any parts should be performed by qualified service personnel only. The use of replacement parts not furnished by Beghelli Canada Inc., may cause equipment failure and will void the warranty.
WIRING DIAGRAM
1. Remove torx screws (9) to release clear cover (1). There are 4 O-rings (10) inserted to the clear cover screw holes. Release the stencil (2) from the clear face cover (1). Knockout to remove the chevron as necessary from the stencil. Peel off backing paper from the tape on the back of the stencil (2) and carefully position and stick the colored fibre to the stencil.
2. Remove the back plate (16) knockouts using applicable knockout holes. Install the liquid tight bushing into the large centre knockout with the lock nut (12). Feed the lead wires through the bushing, tighten to complete the liquid tight seal and install the wall gasket (18) then secure the back plate and housing to the wall. Connect wire per wiring diagram provided. Caution! Failure to insulate unused wire may result in a shock hazard or unsafe condition as well as equipment failure.
3. Replace faceplate, clear cover and torx screws. Note: When installing the cover, be sure to align the light pipe (5) and LED indicator.
4. Apply power.
Parts ListDESCRIPTIONITEM
CLEAR COVER1
STENCIL2
FRAME3
FIBER4
LIGHTPIPE5
LED BOARD6
TEST SWITCH7
CEILING MOUNT GASKET8
TAMPER PROOF SCREWS9
O-RING10
OCTAGON BOX(SUPPIED BT OTHERS)11
BUSHING12
CANOPY GASKET13
CANOPY14
CANOPY MOUNTING BASE15
BACK PLATE16
CAP SCREWS17
WALL MOUNT GASKET18
OVAL HEAD SCREWS19
BATTERY BOX20
1
1
2
2
3
3
4
4
A A
B B
C C
D D
This document is the property of and contains information proprietary to Beghelli Canada, Inc. It is submitted in confidence and is to be used solely for the purpose for which it was furnished and returned upon request. This document and such information is not to be reproduced, transmitted, disclosed, or usedotherwise in whole or in part without prior authorization of Beghelli Canda, Inc. The recepient's acceptance of this document shall be considered an agreement to the foregoing.
UNLESS OTHERWISE SPECIFIEDALL DIMENSIONS = INCHESANGLES + 1/2�
TOLERANCES: .X = � .020 .XX = � .010 .XXX = � .005 .XXXX = � .003
3900 14Th. AvenueMarkham Ontario, L3R 4R3Tel. # 905 948-9500 Fax # 905 948 8673email: [email protected]: http://www.beghelli.com
MATERIAL
FINISH
DRAWN BY DATE
SIZE SCALE
REV
SHEET
PART NAME
DWG NO
REF NODO NOT SCALE
FTZ plus ASSY
6/14/2013
PART #
L D
9
10
1
2
4
7
18
16
11
1213
148
6 3
15
1920
17
5
12
Parts ListDESCRIPTIONITEM
CLEAR COVER1
STENCIL2
FRAME3
FIBER4
LIGHTPIPE5
LED BOARD6
TEST SWITCH7
CEILING MOUNT GASKET8
TAMPER PROOF SCREWS9
O-RING10
OCTAGON BOX(SUPPIED BT OTHERS)11
BUSHING12
CANOPY GASKET13
CANOPY14
CANOPY MOUNTING BASE15
BACK PLATE16
CAP SCREWS17
WALL MOUNT GASKET18
OVAL HEAD SCREWS19
BATTERY BOX20
1
1
2
2
3
3
4
4
A A
B B
C C
D D
This document is the property of and contains information proprietary to Beghelli Canada, Inc. It is submitted in confidence and is to be used solely for the purpose for which it was furnished and returned upon request. This document and such information is not to be reproduced, transmitted, disclosed, or usedotherwise in whole or in part without prior authorization of Beghelli Canda, Inc. The recepient's acceptance of this document shall be considered an agreement to the foregoing.
UNLESS OTHERWISE SPECIFIEDALL DIMENSIONS = INCHESANGLES + 1/2�
TOLERANCES: .X = � .020 .XX = � .010 .XXX = � .005 .XXXX = � .003
3900 14Th. AvenueMarkham Ontario, L3R 4R3Tel. # 905 948-9500 Fax # 905 948 8673email: [email protected]: http://www.beghelli.com
MATERIAL
FINISH
DRAWN BY DATE
SIZE SCALE
REV
SHEET
PART NAME
DWG NO
REF NODO NOT SCALE
FTZ plus ASSY
6/14/2013
PART #
L D
9
10
1
2
4
7
18
16
11
1213
148
6 3
15
1920
17
5
12
Beghelli Canada Inc., 3900 14th Avenue, Markham, ON L3R 4R3 Tel: (905) 948-9500 Fax: (905) 948-8673
Figure 1
926000318
09/18/2013
PARTS LIST1. Clear Cover 2. Stencil 3. Frame4. Fiber 5. Lightpipe 6. LED board 7. Test switch 8. Ceiling mount gasket9. Tamper proof screws 10. O-ring 11. Octagon box (not supplied) 12. Bushing13. Canopy Gasket14. Canopy15. Canopy mounting base16. Back plate17. Cap screws 18. Wall mount gasket19. Oval head screws 20. Battery box
Beghelli Canada Inc., 3900 14th Avenue, Markham, ON L3R 4R3 Tel: (905) 948-9500 Fax: (905) 948-8673926000318