fokofortessa-handles.com/.../uploads/2018/04/fortessa_us_datasheet_f… · independently tested for...

1
independently tested for DIN EN 1906 Quality Standards independently tested for DIN EN 1906 Quality Standards www.fortessa-handles.com FITTING INSTRUCTIONS 1 Decide on left opening or right opening 2 Install lever as per drawing. Note; Leave screws slightly loose 3 Adjust position, to make sure the lever turns smoothly 4 Fitting guidelines video available to view on our website CLEANING INSTRUCTIONS: Always use a Soft cloth. If necessary, you can humidify the soft cloth. If absolutely necessary on rare occasions you can use a PH neutral soap on a soft cloth but immediately after application, you should remove any soap with the help of a moist soft cloth. Under no circumstances should a hard tool (brush or wire metallic cloth), or an abrasive or acidic substance be used on the door lever. SPECIAL WARNING ON CORROSIVE AIR: Please be aware that environments where there are high concentrations of chemicals in the air, eg. emanating from low quality paint or corrosive agents, corrosion & damage may occur to the surface of the door lever. Door levers should not be fitted into such environments until the high concentrations of chemicals in the air have subsided. Fortessa levers are quality tested for their corrosion resistance properties. This test is performed using salt atomized spray. It is important that our levers are installed in the correct environment for their classification category. To maximise your enjoyment of our products, our levers should be fitted according to the fitting instructions and cared for according to the care instructions. Our levers should be installed according to the relevant category of use specified by DIN EN 1906 classification. Category of use Durability Fire Resistance Safety for Persons Corrosion Resistance Security Type of Operation 1 6 0 0 2 0 B Lever Handle o-ring Wood Screw Rose Strike Plate Dust Cover Latch Face Plate Latch Split Spindle Lever Handle Rose (Privacy) Privacy Push Pin Machine Screw (M4) Allen Key CLASSIFICATION - DIN EN 1906 Category of use Internal residential use Durability 100,000 cycles Finish Dual finish of satin chrome and polished chrome Code FUSA-FOK-SCPC Lever base material Zinc alloy Corrosion resistance 48 hours salt atomised spray Weight 810g Door thickness 35mm - 45mm Spindal size 33mm - 48mm Angle of rotation 0° 50° Rotational torque 20Nm Axial load 300N Standard latch 60mm (included) Alternative latch 70mm (available separately) Additional finish NA Lever function Available in ‘Privacy’, ‘Passage’ and ‘Dummy Version’ foko

Upload: others

Post on 02-Aug-2020

9 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: fokofortessa-handles.com/.../uploads/2018/04/Fortessa_US_DataSheet_F… · independently tested for DIN EN 1906 uality Standards independently tested for DIN EN 1906 uality Standards

independently tested for

DIN EN 1906 Quality

Standards

independently tested for

DIN EN 1906 Quality

Standards

www.fortessa-handles.com

FITTING INSTRUCTIONS1 Decide on left opening or right opening2 Install lever as per drawing. Note; Leave screws slightly loose3 Adjust position, to make sure the lever turns smoothly4 Fitting guidelines video available to view on our website

CLEANING INSTRUCTIONS: Always use a Soft cloth. If necessary, you can humidify the soft cloth. If absolutely necessary on rare occasions you can use a PH neutral soap on a soft cloth but immediately after application, you should remove any soap with the help of a moist soft cloth.Under no circumstances should a hard tool (brush or wire metallic cloth), or an abrasive or acidic substance be used on the door lever.

SPECIAL WARNING ON CORROSIVE AIR: Please be aware that environments where there are high concentrations of chemicals in the air, eg. emanating from low quality paint or corrosive agents, corrosion & damage may occur to the surface of the door lever. Door levers should not be fitted into such environments until the high concentrations of chemicals in the air have subsided.

Fortessa levers are quality tested for their corrosion resistance properties. This test is performed using salt atomized spray. It is important that our levers are installed in the correct environment for their classification category. To maximise your enjoyment of our products, our levers should be fitted according to the fitting instructions and cared for according to the care instructions. Our levers should be installed according to the relevant category of use specified by DIN EN 1906 classification.

Category of use Durability Fire Resistance Safety for Persons Corrosion Resistance Security Type of Operation 1 6 0 0 2 0 B

Lever Handle

o-ring

Wood Screw

Rose

Strike Plate

Dust Cover

Latch Face PlateLatch

Split SpindleLever Handle

Rose (Privacy)Privacy Push Pin

Machine Screw (M4)

Allen Key

CLASSIFICATION - DIN EN 1906

Category of use Internal residential use Durability 100,000 cycles Finish Dual finish of satin chrome

and polished chrome Code FUSA-FOK-SCPC Lever base material Zinc alloyCorrosion resistance 48 hours salt atomised spray

Weight 810gDoor thickness 35mm - 45mmSpindal size 33mm - 48mmAngle of rotation 0° 50°Rotational torque 20NmAxial load 300N

Standard latch 60mm (included) Alternative latch 70mm (available separately)Additional finish NALever function Available in ‘Privacy’, ‘Passage’

and ‘Dummy Version’

foko