flushmaster flush valves, demand & metering taps - … valves brochure new ci 2.pdf · fm1.000,...
TRANSCRIPT
TECHNICAL RANGE
Flushmaster Flush Valves,Demand & Metering Taps
Flushmaster Flush ValvesWATER-SAVING TOILET FLUSH MECHANISMS
The flush valves allow for adjustable water delivery and non-hold open function. These can be presetto deliver only enough water to clean the urinal or toilet and no more. They also cannot be left in theopen position, and therefore have to be re-activated for another flush.
Cobra Flush Valves
The dual flush toilets are fitted with a dual flush activation that will dispense either a 3 litre or 6 litreflush.
Cobra Dual Flush Toilets
Standard Flushmaster Flush Valves
Description:Code:
Exposed type with wall plate, inlet control stop.FM1.000
TOILET FLUSH VALVE
FM1.000, STANDARD MANUAL FLUSHMASTER FLUSH VALVEBASIC INSTALLATION GUIDE
Please take note that the following fixtures/ installations should be completed before installing theflushmaster flush valve:
The water supply line should be ideally installed in a brick wall (110mm or 230mm) and the pipingshould be chased into the wall. The water supply line should then be plastered/ tiled closed.This will prevent unnecessary movement of the flushmaster flush valve when operated.
“ ”
Water closet (toilet) or Urinal
Drain line
Waste pipes
Water supply line
1)A
Install the control stop assembly (BC-FM8.60)- - and wall flange. PFT-tape or hempshould be used on the male threads to create aleak-free coupling.
“ ”
FM1.000, STANDARD MANUAL FLUSHMASTER FLUSH VALVEBASIC INSTALLATION GUIDE
All plumbing is to be installed according to the applicable regulations, rules, codes and procedures.Water supply lines and piping must be sized to provide the adequate volume of water for every
flush cycle (60l/ min).Take note of the minimum required operating pressure (30 - 300kPa) of the device (a pressure
pump may be installed to increase the water supply pressure to the minimum required/ desiredlevels).
Take care not to exceed the maximum operating pressure (600kPa) for the specific device (a PRV- pressure reducing valve) can or should be installed on the main water supply line to balance
the water pressure.Flush all water line prior to installation to clear it of any potential debris.
Do not use any toothed tools to install or service the flushmaster flush valve - this will result in“ ”
IMPORTANT NOTE:
INSTALLATION PROCEDURE (only for the Flushmaster flush valve):
2) Prior to inserting the flushmaster flush valve“tailpiece” - - (the end which inserts intothe control stop assembly), take note that the“o-ring” seal - - is located in the “o-ring sealgroove” (see the end of the “tailpiece”) and thatthe “lock nut” - - and “double cap seal” - -are located and positioned as shown.
B
C
D E
3) Insert the flushmaster flush valve tailpiece intothe control stop assembly and hand-tighten thelock nut to the stop control assembly. Plumbthe entire unit now.
“ ”
a. (FMT1.1) back entry.b.
c. (FMT1.2) top entry.
Flushpipe to connect the flushmaster flush valve to the toilet -Rubber pan connector (C-FMV8.3) to enable a leak free/ odour free connection between theflushpipe and the water closet (toilet).Flushpipe to connect the flushmaster flush valve to the water closet (toilet) -
ADDITIONAL REQUIREMENTS:
FM1.000, STANDARD MANUAL FLUSHMASTER FLUSH VALVEBASIC INSTALLATION GUIDE
SPARES AVAILABLE:
INSTALLATION PROCEDURE, CONTINUED (for the installation of the Flushpipe):
FMT1.1
FMT1.2
FMT1.3
FMT3.4CP
- 38.2mm (BENT); 335mm (VERTICAL LENGTH); 140mm (HORIZONTAL LENGTH)
- 38.2mm (STRAIGHT); 203mm (VERTICAL LENGTH)
- 38.2mm (BENT); 508mm (VERTICAL LENGTH); 280mm (HORIZONTAL LENGTH)
- 38.2mm (STRAIGHT); 445mm (VERTICAL LENGTH)
1.2.3.4.5.
Piston assembly (C-FM8.30)Plunger assembly (C-FM8.60)Control stop assembly (C-FMC1.3)Top cover assembly (C-FMC1.2)Headpart (C-FM8.32)
6.7.8.9.
Washer kit (C-FM8.50)Flushpipe coupling nut (C-FM8.14)Handle seal (C-FM8.70)Handle & Nut assembly (C-FMC1.5)
4)F
Determine the length of the flushpipe/ vacuum breakertube - . This pipe is required to connect the flush-master flush valve and the water closet (toilet) and asindicated above, it comes in various lengths (verticaland bent).
5) Hand-tighten the coupling nut at the insertion of theflushpipe to the flushmaster flush valve and insert therubber pan connector into the opening of the watercloset (toilet). Ensure that the rubber pan connectorfits tightly and insert it fully to establish a proper seal.
6)
G
Before the water supply isturned on, ensure all stopvalves to the flushmasterflush valve are closed offproperly. The stop valvescan be opened/ closed/adjusted using theadjustment screw (at thecentre of the control stopassembly) - .
If for any reason the control stop valve needs to be removed completely,ensure that the water supply is turned off completely.
FM1.000, STANDARD MANUAL FLUSHMASTER FLUSH VALVEBASIC INSTALLATION GUIDE
For new installations and servicing of the cartridge:
After completion:a.
b.
c.
d.
Close the control stop valve(or alternative stop valves).Remove the flushmaster flushvalve top cover again.Re-fit the piston/ cartridge andsecure properly.Open the control stop valve(or alternative stop valves).
a.b.c.
Close off the water supply.Lift out the piston valve/ cartridge.Re-fit the flushmaster flush valve top cover - open the water supply gradually to flush outpotential debris and impurities in the water supply.
INSTALLATION/ FUNCTIONING PROBLEMS:
PROBLEM CAUSE SOLUTION
Valve does not operate Water supply Check water supply
Valve does not shut off Dirt in piston bypassDirt/ debris at valve seatDirt/ debris at sealing area
Clean bypass groove (*)Clean valve seatClean piston
Insufficient water Incorrect flushmaster for applicationControl stop valve incorrectlyinstalledPiston damagedPiston stroke too short
Check requirementsAdjust control stop valveReplace pistonTurn piston adjustmentscrew anti-clockwise
Too much waterNoisy flush
Incorrect flushmaster for applicationControl stop valve improperly adjusted
Piston stroke too long
Check requirementsAdjust screw at controlstop valve clockwiseTurn piston adjustmentscrew clockwise
Lever assembly leaks Lever nut is looseFibre washer damagedU-packing dirty
Tighten nutReplace washerDisassemble lever &clean u-packing
BYPASSGROOVE*
Description:Code:
Exposed type. Back entry + flush pipe pan connector.FM1.100
TOILET FLUSH VALVE
Description:
Code:
Exposed type. Top entry + flush pipe pan connector,integral vacuum breaker.FM1.210
TOILET FLUSH VALVE
Description:
Code:
Exposed type with integral vacuum breaker andwall flange.FM2.000
TOILET FLUSH VALVE
Description:
Code:
Exposed type. Back entry with integral vacuumbreaker. Pan connector and wall flange.FM2.100
TOILET FLUSH VALVE
Description:
Code:
Exposed type. Top entry with integral vacuum breaker. Panconnector and wall flange.FM2.210
TOILET FLUSH VALVE
Description:
Code:
Concealed type. Back entry + palm press. Panconnector and control stop.FM3.402
TOILET FLUSH VALVE
Description:
Code:
Exposed type with integral vacuum breaker. Econoflush, 1¼” butterfly control inlet.KF1.000
TOILET FLUSH VALVE
Description:
Code:
Exposed type. Back entry with integral vacuumbreaker. Pan connector. Econoflush.KF1.104
TOILET FLUSH VALVES
Description:
Code:
Concealed type. Back entry + palm press. Panconnector. Econoflush.KF3.402
TOILET FLUSH VALVES
Description:
Code:
Concealed type. Back entry with palm press. Panconnector. Econoflush.KF3.402PR
TOILET FLUSH VALVE
Description:
Code:
Standard Econoflush front access box. Back entrywith flushpipes, galvanised steel under tile box and steelface plate.KF3.412
TOILET FLUSH VALVE
Description:
Code:
Junior Econoflush front access box. Back entrywith flush pipes.KF4.213
TOILET FLUSH VALVE
Description:
Code:
Concealed type. Palm press pushbutton assembly.Econoflush.FJ8.102
TOILET FLUSH VALVE
Junior Flushmaster Flush Valves
Description:
Code:
Exposed type with ball-o-stop and wall flange.Chrome plated finish.FJ2.000
TOILET FLUSH VALVE
Flushmaster Junior SlimlineToilet Flush Valve
Description:
Code:
Exposed type with ball-o-stop and wall flange. Econoflush.Brushed chrome finish.FJ2.001
TOILET FLUSH VALVE
Description:
Code:
Exposed type. Back entry with flush pipe, Pan connector,wall flange and seat buffer.FJ2.100
TOILET FLUSH VALVE
0
10
20
30
40
50
60
70
1 2 3 4 5 6 7
Flush time/ sec
Flo
wra
telt
rs/
min
Description:
Code:
Exposed type. Top entry with flush pipe, pan connector, wallflange and seat buffer.FJ2.210
TOILET FLUSH VALVE
Description:
Code:
Exposed type. Back entry with flush pipe, pan connectorand seat buffer.FJ2.601
TOILET FLUSH VALVE
Description:
Code:
Concealed type with ball-o-stop inlet. Econoflush withcaptive linkage.FJ4.001
TOILET FLUSH VALVE
Description:
Code:
Concealed type. Back entry with flush pipes, pan connectorsand palm press. Econoflush with captive linkage.FJ4.203
TOILET FLUSH VALVE
Description:
Code:
Concealed type. Back entry with vandal resistantguide tube pushbutton assembly and captive linkage.FJ4.203PR
TOILET FLUSH VALVE
Description:
Code:
Exposed type with ball-o-stop and wall flange.Chrome plate finish. Additional toilet piston screw.FJ6.000
URINAL FLUSH VALVES
Flushmaster Junior Slimline - Urinal Flush Valve
Description:
Code:
Exposed type with ball-o-stop. Econoflush. Brushedchrome finish. Additional toilet piston screw.FJ6.001
URINALS FLUSH VALVES
Description:
Code:
Concealed type with Palm press pushbuttonassembly. Econoflush .FJ8.102
URINAL FLUSH VALVE
JUNIOR FLUSHMASTER FLUSH VALVES
0
4
8
12
16
20
24
28
0 1 2 3 4 5 6 7 8 9 10
Flush time/sec
Flo
wra
telt
rs/
min
Flushmaster junior urinal flush valve graph illustrating flushing. Inlet flow pressure of 100kPa with ball -O - stop valve fully open.
Description:
Code:
Front access box with palm press, tailpipe, face plate andball-o-stop. Brushed chrome finish.KF8.112
URINAL FLUSH VALVE
Description:Code:
Exposed type + ball-o-stop and wall flange, chrome plated.FJS2.000
URINAL FLUSH VALVE
Description:
Code:
Exposed type with ball-o-stop and wall flange. Chromeplated.FJS6.000
URINAL FLUSH VALVE
Description:
Code:
Exposed type. Back entry with flush pipe, pan connector,wall flange and seat buffer.FJS2.100
TOILET FLUSH VALVE
Description:
Code:
Exposed type, touch - free, electronic control valve. Chromeplated.EL-3004
URINAL FLUSH VALVE
Description:Code:
Concealed type, touch - free, electronic control valve.EL-3005
URINAL FLUSH VALVE
Description:
Code:
Concealed type, touch - free, electronic control withmanual override button.EL-3006
URINAL FLUSH VALVE
Description:
Code:
Square finish, modern, concealed touch - free, electronicdual flush control with manual override button.EL-4.213
URINAL FLUSH VALVES
Description:
Code:
Square finish, modern, concealed touch - free, electroniccontrol valve.EL-8.112
URINALS FLUSH VALVES
JUNIOR FLUSHMASTER FLUSH VALVES - BASIC INSTALLATION GUIDE
1. Flushmaster Junior Toilet Flush Valves150-500kPa (back-entry WC) 200-500kPa (top-entry WC).
2. Flushmaster Junior Urinal Flush Valves30-300kPa (inlet).
3.105l/ min.
varies
4.60mm
5.6.
are suitable for operation with flow pressures rangingfrom and
are suitable for operation with flow pressures rangingfromThe water supply system should be designed so as to yield a minimum flow-rate at each valve.The minimum flow-rate requirement for a Flushmaster toilet flush valve: The minimumflow-rate required for a Flushmaster urinal flush valve: (depending on the type of urinalused).Valves must be accessible for maintenance/ servicing and a suggested minimum clearance of
is required above the unit for this purpose.The outlet of the flush valve must face vertically downwards.Please consult the table below:
MIN STATIC PRESSURE@ WATERMETER
kPa
300
350
400
450
500
550
600
650
700
MAX LENGTH OF PIPE (M)BETWEEN FLUSH VALVE
AND WATERMAIN
22mm Pipe
3
9
12
14
18
22
29
34
41
1.
2.
3.
The flow-rate, cycle time and flow pressure
in flush valves can be adjusted at the
ball-o-stop screwdriver slot (indicated by
arrow on the line drawing on the left).
The ball-o-stop setting should be such that
there is no splashing whilst ensuring an
adequate flush to clear the pan/ urinal.
Flush time can be adjusted by loosening
the grub screw under the pushbutton and
rotating the knulled button surround 180
(indicated by black dot on the line drawing
on the left).
˚
15mm Ø Pipe or 15mm Ø Watermeter must not be used for toilet flush valves.Friction loss across a 22mm Ø Watermeter has been taken into account (see table above).Maximum distance as indicated may be increased by 25%, if PVC/ HDPE pipe is used.The table is illustrative of single storey domestic applications only and for any other installations,you should consult your Plumber or suitably qualified person to do so.
VALVE SETTINGS:
JUNIOR FLUSHMASTER FLUSH VALVES - BASIC INSTALLATION GUIDE
MAINTENANCE OF THE FLUSH VALVE
When to clean the Flush Valve:or
Removal of the Valve Components:or
Cleaning Procedure:
Checking Valve Performance:Flushmaster Junior Toilet Flush Valve ±6.5l/ flush cycle
Flushmaster Junior Urinal Flush valve yields ±1.8l/ flush cycle;5-16 sec 1-6 sec;
Flush valve not closing due to foreign matter between the seat pipe and the diaphragm underthe relief valve; The by-pass assembly is blocked.
Close the ball-o-stop stop cock; Unscrew the cover; Remove the piston; To dismantle thepiston, unscrew the relief valve top screw and remove the relief valve and relief valve washer.
Gently clean the top of the seat pipe, the underside of the diaphragm, the relief valve washer andthe relief valve seat within the piston plate; The by-pass assembly and if blocked can be cleaned
with a needle.
When operating the , the valve yields andthe The period of flow for urinal
flush valves should ideally range and for the toilet flush valve The flush valvehas
FAULT FINDER
PROBLEM CAUSE ACTION TO BE TAKEN
Poor flowExcessive flush timeValve not shutting off
Dirt in by-pass, valve seator relief valve seat
Follow cleaning instructions
Poor/ excessive flow of waterFlush time too long/ short
Incorrect ball-o-stop setting Adjust ball-o-stop
Excessive flush time and/ orpoor flowValve not closing offNon hold-open feature notworking
Inadequate supply pressure Consult table 1 or yourPlumber or any suitablequalified person able tocalculate systempressures and watersupply
Flush time too short/ long Faulty by-passBy-pass blocked
Clean/ replace by-pass
Valve leaking into pan Diaphragm/ relief valvewasher damage
Insert new piston assembly
Water hammer Air in the system Fit air release valve
Valve leaking at airinlet point
Back pressure from pandue to blockage
Clean pan inlet ports
Cobra Demand Taps
Cobra Metering Taps
The demand taps allow water to flow only as long as the button is held down. They cannot be leftrunning. This feature makes demand taps the ideal choice for public facilities. Only one hand can bewashed at a time.
The metering taps allow an adjustable water delivery time from 1 second minimum. They can bepreset to deliver the minimum amount of water required. Water is dispensed only after the pushbutton has been released. The unit can not be jammed open, both hands can be washed at the sametime.
Cobra Water - SavingDemand and Metering Taps
DEMAND TAP
Demand TapKM2.202-20
Flo
w/
L/
min
Flow Pressure/ kPa KM2.202-20
0
1
2
3
4
5
6
7
350 40010 50 100 150 200 250 300
Description:
Code:
Pushbutton with hot and cold indices included.Chrome plated. ¾” BSP male inlet..KM2.202-20
BIB TAP
Description:
Code:
Pushbutton with hot and cold indices included.Chrome plated. ½" BSP male inlet.KM2.202-15
BIB TAP
Description:
Code:
Pushbutton with raised nose includes hot and cold indices.½" BSP male inlet.KM2.102
PILLAR TAP
Description:
Code:
Pushbutton includes hot and cold indices.Rough brass. ½" BSPKM2.203-15
male inlet.
BIB TAP
Description:
Code:
Pushbutton includes hot and cold indices.Rough brass. ¾” BSPKM2.203-20
male inlet.
BIB TAP
Description:
Code:
Exposed pushbutton stop tap. Chrome plated finish.½” BSP female inlets.KM2.302
STOP TAP
Description:
Code:
Self closing, non - hold open. Flow controller.Flow cycle 1-20 seconds. Chrome plated finish. ½”BSP
KM2.100male inlet.
PILLAR TAP
Description:
Code:
Self closing, non - hold open. Flow controller. Flow cycle 1-20 seconds. Brushed chrome finish.½” BSPKM2.101
male inlet.
PILLAR TAP
Description:
Code:
Exposed with integral ball-o-stop. Non - hold open.¾” BSP feKM1.000
male inlet.
FLOW CONTROL VALVE
METERING TAPS SPECIFICATION
Cobrawatertech (Pty) LtdFlow test on KM2.100 with grub screw
0
500
1000
1500
2000
2500
5 10 15 20
ML
'S
SECONDS
50 KPA 150 KPA 300 KPA
Description:
Code:
Self closing, non - hold open. Flow controller.Flow cycle 1-20 seconds. Chrome plated finish. ½”BSP
KM2.200male inlet.
BIB TAP
Description:
Code:
Self closing, non - hold open. Flow controller.Flow cycle 1-20 seconds. Brushed chrome finish. ½”BSP
KM2.201male inlet.
BIB TAP
Description:
Code:
Self closing, non - hold open. Flow controller.Flow cycle 1-20 seconds. ½” BSPKM2.301
male inlet.
STOP TAP
Description:
Code:
Self closin, non - hold open. Flow controller.Flow cycle 1-20 seconds. Integral shut-off valve. ½”BSP
KM6.000male inlet.
URINAL VALVE