fixed panic panel - sherlotronics · description and functions of the fixed panic panel the ver 4...
TRANSCRIPT
FIXED PANIC PANEL
Part No :
FPP2 (C)
Code Hopping Version
Battery not included
TYPICAL ALARMRADIO
TX
FIX
ED
PA
NIC
PA
NE
LM
od
el:
FP
P
ST
RO
BE
PA
NIC
SIR
EN
AC
FA
ILD
C O
UT
+_
RE
DB
LK
PA
NIC
RE
SE
T
+_
+_
+ _
VO
LT
IN
PU
T +_
CO
MN
.O
10A 120VAC10A 24VDCDC12V
LE
AR
NE
RA
SE
CO
MN
.ON
.C
Ne
w F
ea
ture
:E
rasi
ng
in
div
idu
al
rem
ote
s
Wiring Detail
Ver: 4 Auto low battery cutoff
For more info visit our web site: www.sherlotronics.com Technical help :- 011-462-5101 For more info visit our web site: www.sherlotronics.com Technical help :- 011-462-5101
MU
TE
BU
ZZ
ER
4 5
Pa
nic
1 6
NE
G
Ala
rm 2
Lo
ck
/op
en
3
PO
S
Positive output 140mA
(Battery Negative)
(Battery Positive)RED
BLACK
Input 14V - 14.2V DC (NEGATIVE)
Input 14V - 14.2V DC (POSITIVE)
From SWITCH MODE PSU
Reset
Reset
Description and functions of the Fixed Panic Panel
The Ver 4 Fixed Panic Panel is designed to activate its Relay output when either a remote or hard-wired panic button is pressed. The unit will switch the PANIC output relay for 3seconds. The unit will Latch the Strobe output. The Siren output will stay on for 3Minutes. The unit can be reset thus switching the Strobe Light and Siren Outputs off byeither the Reset input or by Pressing the remote transmitter again.The battery voltage is monitored and in a power-failure the battery will be isolated from the circuit if the voltage measures below 10V. When the AC input is restored the unit will switch back on and start to charge the battery.
Specifications
Encryption.............................................. Code Hopping encryptionFrequency................................................403.55Mhz Range open air line of site...................... 200m Range indoors..........................................60mVoltage range..........................................110 - 240 Volt AC / 50HzInternal Power supply..............................14.2V DC 3 AmpCurrent drain............................................20mA, @ 12.6VDCRelay Output............................................2 second momentary (Radio / Aux) ..............................................3 Minute (Siren) ..............................................Latching till reset (Strobe)
Dimensions...............................................270 X 240 X 70mmWeight of packaged product......................0.80Kg
Package Contents:
One Fixed Panic Panel unitTwo Single Button Remote panic buttons. Model: PTX1 One Installation guide
Deleting all codes / Defaulting.
Defaulting
Erasing Individual remotes
LEARN
LEARN
ERASE
Press and hold for longer than 10 Seconds.When the unit sounds a Long Beep you can stop pressing the button and then wait for it to silence.
Press the buttonto be erased
Repeat for each remoteto be erased.
You must eraseone remoteat a time.
This function will Default ( Erase all) remotes from the units memory
Link On
20 beeps
For more info visit our web site: www.sherlotronics.com Technical help :- 011-462-5101
Long beep
Programming Please follow the steps below to Learn in remotes to the receiver. The unit can store up to 80 remotes. When memory has reached its limit the unit will automatically exit out of program mode and sound a long beep. The unit auto exits after 10 seconds.
LEARN
Step 1. Step 2.
Step 3.
Press button twice
Exits from Learn
Step 4.
LEARNContinue with Step 2 to Learn in all the remotesA Max of 80 remotes can be learnt to memory
Enters Learn mode
1 beep 2 beeps
Long beep
Installation Guide
For more info visit our web site: www.sherlotronics.com Technical help :- 011-462-5101
Model: PTX1