first page of subramani thesis (part-1)
TRANSCRIPT
![Page 1: First Page of Subramani Thesis (Part-1)](https://reader030.vdocuments.us/reader030/viewer/2022013118/5540c9324a7959e10e8b4af5/html5/thumbnails/1.jpg)
EXPERIMENTAL STUDY AND ANALYSIS OF OPERATING PARAMETERS IN EDM PROCESS THROUGH RESPONSE SURFACE METHODOLOGY
By
Mr. D.SUBRAMANI
Registration Number: 811411410012
of
Jayaram College of Engineering & Technology
Pagalavadi, Tiruchirappalli – 621 014.
A PROJECT REPORT PHASE – I
Submitted to the
FACULTY OF MECHANICAL ENGINEERING
In partial fulfillment of the requirements
for the award of the degree
of
MASTER OF ENGINEERING
IN
MANUFACTURING ENGINEERING
ANNA UNIVERSITY, CHENNAI 600 025. DECEMBER 2012
![Page 2: First Page of Subramani Thesis (Part-1)](https://reader030.vdocuments.us/reader030/viewer/2022013118/5540c9324a7959e10e8b4af5/html5/thumbnails/2.jpg)
BONAFIDE CERTIFICATE
Certified that this Project report Phase I titled “EXPERIMENTAL STUDY AND
ANALYSIS OF OPERATING PARAMETERS IN EDM PROCESS
THROUGH RESPONSE SURFACE METHODOLOGY’’ is the bonafide work
of D.SUBRAMANI (Registration Number: 811411410012) who carried the project
work Phase-I under my supervision. Certified further, that to the best of my
knowledge the work reported herein does not form part of any other thesis or
dissertation on the basis of which a degree or award was conferred on an earlier
occasion on this or any other candidate.
HEAD OF THE DEPARTMENT SUPERVISOR
Mr. K.SURESH KUMAR., M.TECH., (Ph.D) Mr. K.R.THANGADURAI., M.TECH., (Ph.D)
Asso professor, Department of MECH, Asst Professor, Department of MECH,
Jayaram College of Engineering & Jayaram College of Engineering &
Technology, Technology,
Pagalavadi, Tiruchirapalli-621 014. Pagalavadi, Tiruchirapalli-621 014.
Submitted for the University Project Phase I Viva Vice Examination
held on ---------------------------------------------------
External Examiner Internal Examiner
![Page 3: First Page of Subramani Thesis (Part-1)](https://reader030.vdocuments.us/reader030/viewer/2022013118/5540c9324a7959e10e8b4af5/html5/thumbnails/3.jpg)
ACKNOWLEDGEMENT
First and Foremost I am highly thankful to the almighty god for blessing
with necessary wisdom to accomplish this project work
I would like to thank our respected Chairman Er.M.SUBRAMANIAM.
M.E. and Principal Dr. N.KANNAN Jayaram College of engineering &
technology, for their encouragement and blessings.
I gratefully thank to our Head of Department Mr. K.SURESH KUMAR.,
M.TECH., (Ph.D) for providing the opportunity and encouragement to do this
project.
I take extensive privilege in expressing sense of gratitude and heartfelt
thanks to our guide Mr. K.R.THANGADURAI., M.TECH., (Ph.D) for his
contribution to finish our project in successful manner.
We express our heartfelt thanks to all the Faculty members, Technical
assistants and Non-teaching Staffs of the Department of Mechanical
Engineering for their timely assistance.
Our humble gratitude and thanks to our parents, for their love,
encouragement and support to do this project work.
Above all I express my deep gratitude to the almightily, who guide and help
me in all words.
![Page 4: First Page of Subramani Thesis (Part-1)](https://reader030.vdocuments.us/reader030/viewer/2022013118/5540c9324a7959e10e8b4af5/html5/thumbnails/4.jpg)
TABLE OF CONTENTS
CHAPTER NO TITLE PAGE NO
1 ABSTRACT 1
2 INTRODUCTION 2
3 LITERATURE REVIEW
4 METHODOLOGY
5 RESULT AND DISCUSION
6 CONCLUSION
REFERENCES
PHOTOGRAPH
![Page 5: First Page of Subramani Thesis (Part-1)](https://reader030.vdocuments.us/reader030/viewer/2022013118/5540c9324a7959e10e8b4af5/html5/thumbnails/5.jpg)
EXPERIMENTAL STUDY AND ANALYSIS OF OPERATING PARAMETERS IN EDM PROCESS
THROUGH RESPONSE SURFACE METHODOLOGY