THE PHOTO GIFTS ITENS ARE NOT INCLUED.

+

A new generation of sublimation printing technology. These machines are multi-functional. They can print mugs, plates, ceramic tiles, crystals, glasses, cell phone cases, ipad cases etc.

VACUUM HEAT PRESS MACHINE3D SUBLIMATION

ColoursAvailable in

Various

SKU: 3DSUB-black

SKU: 3DSUB-red

SKU: 3DSUB-green

SKU: 3DSUB-blue

SKU: 3DSUB-silver

Find out more information on our website

THE PHOTO GIFTS ITENS ARE NOT INCLUED.

+

A new generation of sublimation printing technology. These machines are multi-functional. They can print mugs, plates, ceramic tiles, crystals, glasses, cell phone cases, ipad cases etc.

VACUUM HEAT PRESS MACHINE3D SUBLIMATION

ColoursAvailable in

Various

SKU: 3DSUB-black

SKU: 3DSUB-red

SKU: 3DSUB-green

SKU: 3DSUB-blue

SKU: 3DSUB-silver

Find out more information on our websiteTHE PHOTO GIFTS ITENS ARE NOT INCLUED.

+

A new generation of sublimation printing technology. These machines are multi-functional. They can print mugs, plates, ceramic tiles, crystals, glasses, cell phone cases, ipad cases etc.

VACUUM HEAT PRESS MACHINE3D SUBLIMATION

ColoursAvailable in

Various

SKU: 3DSUB-black

SKU: 3DSUB-red

SKU: 3DSUB-green

SKU: 3DSUB-blue

SKU: 3DSUB-silver

Find out more information on our websiteINSTRUCTION MANUAL

Contents

P2. Safety Instructions

P3. Contents

P4. Features

P5. Compatible Products

P6. TechnicalSpecifications P7. Inside the Box

P8. Operation Instructions

P10. The Vacuum Tray

P11. Replacing Parts & Draining Filter

P12. Producing Mugs

P13. Producing Plates

P14. Producing Phones (Metallic Sheet Method)

P15. Producing Phones / Tablets (Plastic Full Cover)

P16. Producing Acrylic Frame

P17. Producing Ceramic Tile

P18. Troubleshooting

Important Safety Instructions When using your 3D Sublimation machine, basic precautions should always be used including the following points:

1. Read all instructions

2. Use 3D Heat Press only for its intended purpose

3. To reduce the risk of electric shock do not expose the 3D Sublimation Vacuum Heat Press to water or other liquids.

4.Whenfinishedwithmachine,turnunitoffbeforedisconnecting the plug from the socket. Never pull the cord to disconnect from power outlet. Instead grasp plug and pull to disconnect.

5. Do not allow power cord to touch hot surfaces. Please ensure the 3D Heat Press has cooled completely before putting away.

6. Do not operate appliance with a damaged power cord, or if the appliance has been dropped or damaged.

7. To reduce the risk of electric shock, do not disassemble or attempt to repair the 3D Heat Press. Please contact your reseller for examination and repair (based on the terms of your warranty). Incorrectreassemblyorrepaircouldcauseariskoffire,electric shock, or injury to persons when the appliance is used. Any attempt to repair or tamper with the unit will void warranty.

8. Children are not allowed to operate this appliance, please do not leave the appliance unattended while connected.

9. Severe burns could occur from touching hot metal parts.

10. To reduce the likelihood of circuit overload, do not operate another high voltage appliance on the same circuit

11. If an extension cord is absolutely necessary, a 20 amp rated cord should be used. Power cords rated for less amperage may overheat, care should be taken to arrange the cord so that the power cord cannot be pulled or tripped over.

Features:

Safety Software and hardware dual temperature control design, when one thermostat failure, the other thermostat automatically work, 15 minutes no operation, automatic shutdown, more secure and reliable. ThemachinehasappliedforCE\ULsafetycertification

Efficient The 300X420X110mm capacity reactor core design capacity, can put 12 mugs at one time, greatly improve work performance.

Delicate Bump dots surface design, greatly improve the heat area, die-cast aluminum alloy heating far infrared radiation coating, so that each point of the temperature of the furnace are uniform to ensure that the image transfer more delicate and clear.

Simple The machine adopts special high impedance contingent, insulation materials, lightweight and safe, streamlined resistance heat strips, compact and practical internal structure, simple and stylish appearance.

Sharp 108Degreeclamshelldesign,easyoperation,significantspacesaving.

Highly Intelligent Work without any key operation, just gently close the cover, the machine will automatically aspirate, countdown and heat up. Whentheworkiscompleted,automaticallydeflated, All you need is a simple process to place and remove products

User-Friendly Forfirsttimeuse,thetemperatureandtimeset-upprocessisveryeasy to understand and easy to learn.

Environmental Protection Efficientactivatedcarbonairfilterisinstalledinthemachine,effectively to worry too much toxic and harmful gases generated in the transfer process, transported to the outdoors through the long catheter to ensure the health and safety of the operating personnel.

Multifunctional The machine covers all the functions of the heat transfer machine, which can transfer mug, glass, crystal, acrylic, plastic, wood, metal, stone,clothandsoon.withvarioustypesoffixture,candosublimation transfer on different size and shape of mugs. Transfer large format, delicate, clear, high color reproduction, far more than the traditional heat transfer machine.

THERE ARE LOTS OF THINGSTHAT YOU CAN CREATEUSING 3D SUBLIMATION

THESE ARE JUST A FEW OF THEEXAMPLES OF PRODUCTS

THAT YOU CAN MAKE

PLEASE CHECK OUR WEBSITEFOR OUR LATEST RANGEwww.photomart.co.uk

TEDDY BEARS

PHONE COVERS

METAL SHEETS

SHOT GLASSES

PLASTIC FLASKS

ACRYLIC

LAPTOP CASES METAL BOTTLES

PHOTO CLOCKS CERAMIC PLATES

PATCH MUGS

CERAMIC MUGS

MOUSE PADS

JIGSAW PUZZLES

PHOTO ROCKS

CERAMIC TILES

TechnicalSpecifications

Measurement 685 x 545 x 400mm CBM 0.15 CBM

GW 20kg (44lb)

NW 16kg (35lb)

Power 2600W

Voltage 220 V

Working Area 300 x 420 x 110mm (11.8 x 16.5 x 4.3inch)

Up Heating 1200W

Down Heating 1200W

Vacuum Pump 150W

Max Vacuum -640mmHg

Vacuum Flow 33L/min

SILICONESHEET

POWER CABLE

METAL GRILL

INSTRUCTION MANUAL

EXHAUST PIPE

SAFETYGLOVES

3 x MUG WRAPS(VARIOUS STYLES)

ADDITIONAL ACCESSORIES

INSIDE THE BOX

Operating Instructions For best results, the 3D Sublimation Machine should be placed on alevel,clean,stable,well-ventilatedworkareafreeofflammable materials. It is recommended that the unit be plugged directly into an AC power outlet.

When operating the machine, heat protection gloves should be worn at all times to prevent serious burns or other injuries.

Please keep the machine dry and away from water.

Removal from Box

1. Remove the 3D Sublimation Machine Carefully from the Box

2. Inspect all cabling, wiring and machine body to ensure the unit has not been damaged in transit.

3. Set unit on a clear table that is strong enough to support your working environment and the weight of the machine.

Cabling

1. The 3D Sublimation Machine comes with the vacuum unit installed inside the main unit. All cables are connected inside before shipment. 2. The Power Cable and Vacuum Exit Hose need to be attached. 3. Plug in power cable to an AC outlet.

Operating the Touch Screen Panel For best results, the 3D Sublimation Machine should be placed on

Buttons IndicatorsHeating Switch

Temperature Settings

Time Settings

Power Switch

Vacuum Switch

Timer Start Switch

Top Heat Tray

Bottom Heat Tray

Vacuum Pump

Timer Indicator

The the first push will turn on the top heater.The second push will turn on the bottom heater.The third push will turn on both heaters. Hold for 3 Seconds to set Temperature Compensation

Turn Switch on FirstPress Button to activate and deactivatethe Standby ModePower is 10w when left on Standby

Push once to activate Temperature SettingsUse + or - Keys to Set TemperaturePush Button again to Confirm Temperature.

Push the Button to activate the Vacuum Pump. Push again to Manually disable the Vacuum PumpIf turned on with the timer, the pump will switchitself off automatically.

Push once to activate Time SettingsUse + or - Keys to Set TimerPush Button again to Confirm Time Setting

When the time has been set, push once to activate.The time is measured in secondsWhen the countdown finished, the heater and vacuum will turn off automatically and will beep 3 times.

Removing the Vaccum Press Tray 1. Ensure the Machine has cooled down to normal temperature

2. Lock the 3D Press Tray using the Handle

3. Open the Lid Fully

4. Lift up the 3D Press Tray Vertically

5. Unscrew the Pipe from the bottom of 3D Press Tray and Remove

6. Remove Metal Grill

7. Unscrew the other end of Pipe from the bottom of Machine

8. Place Metal Grill Back in Place

9. Machine is Ready to be used in Oven Mode.

Replacing the Vaccum Press Tray 1. Ensure Machine has cooled down to normal temperature

2. Lift the Lid Fully

3. Remove the Grill

4. Screw one end of the pipe back into the bottom of machine

5. Replace Metal Grill ensuring pipe goes through it

6. Screw other end of pipe into bottom of vacuum tray

7. Place Vacuum Tray back into the machine

8.Machine is now Ready for Vacuum Mode

Replacing the Air Filter 1. Ensure the Machine is switched off and cool down

2. Use a magnetic screwdriver to remove the screws from back panel

3. Remove the Back Panel

4. Remove Air Filter from its holder (note: do not remove pipes)

5. By Hand, Carefully Unscrew the Glass Cover

6. Empty out the Glass Cover and clean, ensuring it is dry.

7.Unscrewthescrewholdingwhitefilterinplace.

8.Removewhitefilterfromholderanddispose

9. Clean the holder with a small smooth cloth.

10.Replacewithanewwhitefilter.

11. Replace Screw holding it into place

12. By Hand replace the Glass Cover

13. Place Filter Back into Position

14. Replace Back Cover

15. Using Magnetic screwdriver screw cover back into place

16. Machine is Ready for use.

Mugs:

Instructions

1. Prepare your design to the size of your mug

2. Using a Sublimation Printer, Print the design in reverse onto Paper

3. Allow the paper a few minutes to dry 4. When dry, cut the Paper, allowing 0.5cm Blank Edge on each side.

5. Use suitable tape to stick the paper to the mug from the sides

6. PlaceRubberGriparoundtheMugensuringitlocksfirmlyintoplace. 7. Ensure the Tray Section is Removed (refer to section: Vacuum Tray)

8. Turn Vacuum Press Machine on, and set to Temperature 190 degrees, then press the Heating Button twice (2 red lights will light up) 9. When temperature has been reached, place your mug/s (up to 12) upside down onto the grill and close the lid.

10. Set time to the following from 6 Minutes (1 Mug) to 8 Minutes (12 Mugs)

11. Press the Vacuum Button, and the Timing Button and leave the machine.

12. As soon as the time has been reached, the Vacuum will switch itself off automatically and machine will beep

13. Remove mugs, and leave to cool down before removing the paper

Plates:

Instructions

1. Prepare your design to the size of your plate 2. Using a Sublimation Printer, Print the design in reverse onto Paper

3. Allow the paper a few minutes to dry 4. When dry, cut the Paper, and stick it tightly around the edge of the print to plate using appropriate tape

5. Place plate onto the Vacuum Tray of the Machine

6. Cut a Small Strip of Paper, and place it over the edge of one side of the plate (so that part of it is covering plate and part of it is hanging over) 7. Turn Vacuum Press Machine on, and set to Temp 190 degrees, then press the Heating Button twice (2 red lights will light up) 8. When temperature has been reached, place your plates (up to 2) face up onto vacuum tray abd close the lid

9. Set time to the following from 5 Minutes(1 Plate) to 6 Minutes (2 Plates)

10. Press the Vacuum Button, and the Timing Button to start the process.

11. Check that the Rubber Cover Pressed Into the plate rather than over it

12. Close the lid of the Vacuum Press and leave the machine.

13. As soon as the time has been reached, the Vacuum will switch itself off automatically and the machine will beep

14. Remove plate, and leave to cool down before removing the paper

Phone Cover: (Metallic Sheet Method)

Instructions 1. Prepare your design to the size of your sheet (2mm Bleed)

2. Using a Sublimation Printer, Print the design in reverse onto Paper

3. Allow the paper a few minutes to dry 4. Remove the protective sheet from the phone cover and place metal sheet coated down onto the transfer paper. Cut around the paper until you have enough to fold around the metal sheet and stick it using appropriate adhesive tape.

5. Turn Vacuum Press Machine on, and set to Temp 190 degrees, then press the Heating Button twice (2 red lights will light up) 6. When temperature has been reached, place your plates (up to 4) face up onto vacuum tray abd close the lid

7. Set time to the 3 Minutes: (Important Note: Any additional time will bend the metal.)

8. Press the Vacuum Button, and the Timing Button to start the process.

9. Check that the Rubber Cover Clings Tightly Around the Sheet

10. Close the lid of the Vacuum Press and leave the machine.

11. As soon as the time has been reached, the Vacuum will switch itself off automatically and machine will beep

12. Remove plate, and leave to cool down before removing the paper

13. Peel off adhesive cover from the top of the Plastic Phone Cover

14. Stick the Metallic Sheet inplace on the Plastic Phone Cover.

Phone/Tablet Cover: (Full Plastic Cover Method)

Instructions

1. Prepare your design to the size of your Cover 2. Using a Sublimation Printer, Print the design in reverse onto Paper

3. Allow the paper a few minutes to dry 4. When dry, cut the Paper, and stick it tightly around the edge of the print to cover using appropriate tape

5. Place the Cover around the compatible Jig/Mould 6. Turn Vacuum Press Machine on, and set to Temp 190 degrees, then press the Heating Button twice (2 red lights will light up) 7. When temperature has been reached, place your covers (up to 4) cover side up onto vacuum tray and close the lid

8. Set time to the following from 3 Minutes(1 Cover) to 4 Minutes (4 Covers)

9. Press the Vacuum Button, and the Timing Button to start the process.

10. Check that the Rubber Cover goes tightly around the cover.

11. Close the lid of the Vacuum Press and leave the machine.

12. As soon as the time has been reached, the Vacuum will switch itself off automatically and machine will beep

13. Remove cover/s, and leave to cool down before removing the paper

Acrylic Frame:

Instructions

1. Prepare your design to the size of your Acrylic(2mm Bleed)

2. Using a Sublimation Printer, Print the design in reverse onto Paper

3. Allow the paper a few minutes to dry 4. Remove the protective sheet from the back of the acrylic sheet, place acrylic adhesive side down onto your print, and stick around sides using suitable tape

5. Turn Vacuum Press Machine on, and set to Temp.190 degrees, then press the Heating Button twice (2 red lights will light up) 6. When temperature has been reached, place your acrylics onto vacuum tray and close the lid

7. Set time to the 3 Minutes: (Important Note: Any additional time will melt the acrylic.)

8. Press the Vacuum Button, and the Timing Button to start the process.

9. Check that the Rubber Cover Clings Tightly Around the Acrylic and Paper

10. Close the lid of the Vacuum Press and leave the machine.

11. As soon as the time has been reached, the Vacuum will switch itself off and machine will beep

12. Remove Acrylic, and leave to cool down before removing the paper

Ceramic Tiles:

Instructions

1. Prepare your design to the size of your Tile

2. Using a Sublimation Printer, Print the design in reverse onto Paper

3. Allow the paper a few minutes to dry 4. When dry, cut the Paper, and stick it tightly around the edge of the tile using appropriate tape

5. Cut a Small Strip of Paper, and place it over the edge of one side of the plate (so that part of it is covering plate and part of it is hanging over) 6. Turn Vacuum Press Machine on, and set to Temp 190 degrees, then press the Heating Button twice (2 red lights will light up) 7. When temperature has been reached, place your Tile (up to 4) face up onto vacuum tray and close the lid

8. Set time to the following from 5 Minutes(1 Tile) to 6 Minutes (4 Tiles)

9. Press the Vacuum Button, and the Timing Button to start the process.

10. Close the lid of the Vacuum Press and leave the machine.

11. As soon as the time has been reached, the Vacuum will switch itself off and machine will beep

12. Remove plate, and leave to cool down before removing the paper

13. Remove Adhesive Back from Tile Frame, and Stick Tile in Place

Troubleshooting:

Q. Transfer Paper appears yellow after process? A. Lower Temperature and/or Reduce Heating Time

Q: The text appears very faint? A: Lower Temperature and/or Reduce Heating Time

Q. Paper still stays same after process? A. Use Higher Temperature and/or Increase Heating Time

Q: Colours do not appear good on Product? A: Use Higher Temperature and/or Increase Heating Time

Q: Sometimes Get White Stains? A: Use Higher Temperature and/or Increase Heating Time

Q. The Effect does not look good on certain textures? A. Temperature and Time have to be changed accordingly This will be vary based on a number of factors including: - Paper Quality - Printing Machine - Product Texture - Temperature Conditions

Q: Keep getting excess powder around your image? A:Pleaseensureyouhaveallowedsufficienttimeforyoursunlimation print to dry before putting it onto your material

Q: Machine switches off if I leave it alone for a long time? A: This is intentional by design, the machine is set to switch off automatically after 15 minutes making it safe and reliable

Q: The printing appears to be unclear? A: 1) Check the Vacuum guage to see if the vacuum pressure reaches 0.64mmhg. If the pressure fails to reach he value, leakage can be assured. Check the vacuum extracting strip to see if its well sealed. 2) Check connections of pipe for looseness or leakage

Troubleshooting (Continued):

Q. What if automatic operation failed, including air extraction, suction and countdown? A. Adjust the distance between the vacuum extracting plate and the switch. Normally, the distance shall be at 3mm, magnet strength will be weak if the distance is too far.

Q. What if abnormal sound occurs and the machine fails to run normally? A. 1) Open the cover of the rear power box and check if any wind-up on the vacuum fan. If there is, unwire it. 2) Checkifthereisanywaterintheairfilter.Waterneedstobe emptiedandthefiltercorewillneedtobereplacedperiodically.

Q. The Machine fails to heat and temperature does not rise? A. Check if the heating switch has been turned on and the indicators on the display are glistening. If not, turn on the switch.

Q. There is a big gap found between the set and real temperature. A: 1) Overheating within 30 Degrees C is acceptable when the metal heating pipes are working properly 2) Check if the cooling fan beneath the circuit board works normally. If there is any damage, the fan needs to be replaced. 3) The machine is designed with double circuit for temperature control, keeping the inner oven temperature below 210 Degrees C, otherwise the machine will cease heating.

&PHOTO ALBUMPhoto GiftCatalogue

LONDON - UK+44 (0) 20 8527 6006[Mon-Fri 9am to 6pm]+44 (0) 20 8501 8866

[Sat 10am to 5pm]sales@photomart.co.uk

www.photomart.co.uk

TM

PICK UP OR DOWNLOAD A COPY OF OUR PHOTO GIFT CATALOGUETO FIND OUT ABOUT OUR CURRENT RANGE OF SUBLIMATON GIFTS