fig 2a: illustration of macroscopic defects diffusion lengths are calculated by the equation where...
TRANSCRIPT
Fig 2a: Illustration of macroscopic defects
• Diffusion lengths are calculated by the equation where
• μ is the mobility of electron with literature value of 8500 cm2V-1s-1
• k is the Boltzmann constant and q is the electron charge
Note: Initial densities for theoretical calculations over-estimate experimental steady-state conditions
A Recombination Model for GaAs Solar Cells Keyuan Zhou and Tim Gfroerer, Davidson College
Yong Zhang, UNC Charlotte
AbstractSolar cells convert sunlight into electricity. But defects in solar cells are one of the major factors inhibiting conversion efficiency. Defects allow for the recombination of charge carriers, so they fail to contribute to the electrical output. Measurements and preliminary analysis by Ashley Finger (’14) show illumination and temperature-dependent trends in GaAs that help clarify the role of defects. My research aims to develop a new way to analyze the data. In particular, I seek to improve the model describing the recombination process under the influence of defects in the semiconductor material.
What is a GaAs Solar Cell?
What are Defects?
• Occur during the manufacturing process
• Statistically, defects are unavoidable
• Microscopic or bulk defects are misplaced or alternative atoms in the crystal
• Macroscopic defects are extended mismatch features in the crystalline structure
Why do defects matter?• Energy from the incident light is dissipated as heat
• Reduces electrical output
• Heat generation can also damage the cell
Previous Experiments
• Our focus is the recombination process of the electrons and holes around a macroscopic defect.
• Previous work included measurements of response under different illumination at different temperatures ranging from 77K-295K
• We have constructed a physical model and we compare theoretical curves with the experimental results
1014 1015 1016 1017 1018
0
10
20
30
40
50
Temperature 77K 131K 185K 239K 295K
Effe
ctiv
e D
iffus
ion
Leng
th (m
)
Carrier Density (cm-3)
Late this summer, we discovered a new method that uses the differential equation model to fit the data directly without any assumptions/simplifications
1015 1016 1017
0.2
0.4
0.6
0.8
1.0
Temperature 77K 131K 185K 239K 295K
Em
issi
on E
ffici
ency
Steady-State Carrier Density (cm-3)
Working Model and Future Work
Carrier Generation and Recombination
• A device that converts light energy directly into electricity
• GaAs is a crystalline compound of elements gallium and arsenic
• High efficiency but high cost!
Ene
rgy
Valence Band
Conduction Band
Electrons Holes
Photon in Photon out
• Electrons absorb the energy from a photon and jump to a higher energy level
• The vacancies left behind will have an effective positive charge – these vacancies are called holes
• This absorption process is called carrier generation
Fig 3a: Illustration of Carrier generation and recombination
• When the electrons fall down to the lower energy level, a photon may be re-emitted
• The electron fills the hole (a process called recombination) and the time between generation and recombination is called the lifetime
Our Study and Preliminary Model
GaInP
GaInP
GaAs
Upper Confinement Layer
Lower Confinement Layer
Active Layer
Bulk defect region
Interface (macroscopic defect) region
Fig 5a: GaAs sample diagram
Fig 5b: Experimental setup diagram from thesis file of Ashley Finger (’14)
• Ashley Finger (’14) and Dr. Gfroerer made prior measurements on a GaAs sample
• By shining a laser on the sample, electron-hole pairs are generated, and a camera and oscilloscope are used to study the recombination process
• Carriers can diffuse before recombining, and the distance traveled is called the diffusion length
Fig 3b: Illustration of diffusion and laser excitation
Fig 4a: Thermal picture of a solar panel by Dr. Gfroerer Fig 4b: Diagram of defect-related loss
Fig 1: Picture of a solar cell and diagram of its working mechanism
Fig 2a: Illustration of microscopic defects
Fig 6a: Radiative efficiency analysis
Fig 6b: Transient analysis of carrier lifetime
Fig 6c: Diffusion length analysis, open symbols are theoretical results
MODEL
Fig 7: Comparison of the transient data fits with the preliminary model (red and green) and working model (dark green) at 239K