fiesta st rear motor mount install

8/11/2019 Fiesta ST Rear Motor Mount Install

1/6

Breedt Product Design 811 1st

Ave S., Kent, WA 98032

Tel (253) 859-1100 Fax (253) 859-1106

www.breedtproductdesign.com 2014: Breedt Product Design

PARTS:

1ea Assembled RMM 1ea 60 durometer bushing

INSTALLATION INSTRUCTIONS

Rear Motor Mount

2014- Ford Fiesta ST

www.breedtproductdesign.com

2. Start by removing the two nuts,

sleeves, and oval plate that attach the

down tube to down tube support bracket

(figure 1).

Figure 1

1.Start by allowing the car to cool down,about an hour. Put the car in gear and

engage the emergency brake. Jack up the

front of the vehicle and support with jack

stands or lift.
http://www.breedtproductdesign.com/http://www.breedtproductdesign.com/


2/6



Tel (253) 859-1100 Fax (253) 859-1106


3. Remove the two nuts holding the

down tube support bracket to the

transmission (figure 2).

5. Remove the two upper bolts holding

RMM bracket to transmission and the

bottom bolt (figure 4).

4. Remove the bracket. Here is a picture

of where the down tube bracket parts

orientate (figure 3).

Figure 4

Figure 3

Figure 2


3/6



Tel (253) 859-1100 Fax (253) 859-1106


6. Remove the bolt holding the RMM

to the sub frame then remove RMM. Be

careful RMM will swing down (figure

5).

7. Place RMM in vise and tap bracket

off with a mallet (figure 6).

8. Insert RMM between ears on sub

frame and insert the shorter of the two

longest bolts that were removed. Do not

tighten bolt yet (figure 7).

Figure 5

Figure 6

Figure 7


4/6



Tel (253) 859-1100 Fax (253) 859-1106


Figure 8

Figure 9

Figure 10

9. Loosely install the factory bracket

(figure 8).

10. Swing RMM up and insert the

longest bolt (figure 9).

11. While threading in bolt make sure

there is no gap between RMM and

bracket. The RMM boss needs to go in

hole on factory bracket (figure 10).


5/6



Tel (253) 859-1100 Fax (253) 859-1106


12. Tighten all 4 bolts to 50 ft/lbs

(figure 11).

Figure 11

13. Reinstall down tube support bracket

(figure 12).

14. If a stiffer RMM is desired replace

preinstalled 40 durometer bushing with

supplied 60 durometer bushing using

instructions below.

Figure 12


6/6



Tel (253) 859-1100 Fax (253) 859-1106


Breedt Product Design has designed the RMM to be used as an off-road performance part.

This product is an optional accessory, put on by the vehicle owner; therefore BPD is not responsible

for any damage that the vehicle might acquire during improper installation or misuse. BPD warranties

this product to be free of manufacturer defects. BPD is not responsible for any parts modified ordamaged during improper installation. If you do not agree with these conditions, please return the

product for a refund.

This part is designed to fit a 2014- Ford Fiesta ST with a six speed manual transmission. If you

feel uncomfortable or lack mechanical skills, we recommend having this product professionally

installed by a qualified mechanic. Please read through the entire packet before beginning to instal

this product. If you do not agree with the conditions in this packet, please return the product to

BPD before installation for a full refund.

Remove RMM using steps outlined

above. Remove the 4 bolts holding the

RMM together. Pull the two halves

apart. Push the bushing out of the

RMM. Pull the two round sleeves out of

the bushing. Insert the 60 durometer

bushing in place of the softer. Put the

two RMM halves together and reinstall

the 4 bolts. Push the two sleeves in the

bushing. Reinstall RMM using steps

outlined above.

fiesta st rear motor mount install

Documents