fh-s•thread:m6 •rechargeable battery pack integrated, standard, operating time up to 12 h...

Measuring system

Measuring range [Max]: 2 N

Overload protection (of [Max]): 150 %

Precision (of [Max]): 0,005

Readout [d]: 0,001 N

Test frequency: 2000 Hz

Display

Display digit height: 1 cm

Functions

Data hold function: yes

Function to set limits: yes

Obtaining average: yes

Peak function: yes

Statistical function: yes

Environmental conditions

Maximum operating temperature: 40 OC

Minimum ambient temperature: 10 OC

Power supply

Charging time: 4 h

Input voltage: 100 V - 240 V

n/a: CH EURO

Power supply

Operating time (Backlight off): 12 h

Service

DAkkS Calibration certificate 963-261

(Pressure):


(Tensile):


(Tensile/Pressure):

ISO calibration certificate: 961-361

ISO Calibration certificate (Pressure): 961-261

ISO Calibration certificate (Tensile): 961-161

ISO Calibration certificate (Ten- 961-361

sile/Pressure):

Category

Brand:

Category: Force gauges

Product Group: Electronic force-measuring

device

Packaging & shipping

Delivery: 24 h

Dimensions packaging (WxDxH): 312 x 170 x 60 mm

Gross weight: 1,300 kg

Net weight: 640 g

Shipping method: Parcel service

UN number: 3496

Construction

Dimensions of display device

(WxDxH):

230 x 66 x 36 mm

Overall dimensions mounted

(WxDxH):

230 x 66 x 36 mm

n/a: Mains adapter external

1

X-SENSORS GmbH l Steinbrechstr. 9, 71106 – Magstadt, Deutschland l Tel: +49 7159/49697-0 l [email protected] l www.sensorshop.com

FH-S X-SENSORS GmbH

Magstadt, Deutschland l Tel: +49 7159/49697-0 [email protected] l www.sensorshop.com Kompetenz in Messtechnik und Kundenbetreuung

01

OPTION

Model

Measuring range

[Max] N

Readout

[d]

N

Option ISO Calibration Certificate Tension Compression Tension/Compression

FH 2. 2 0,001 961-161 961-261 961-361

FH 5. 5 0,001 961-161 961-261 961-361

FH 10. 10 0,005 961-161 961-261 961-361

FH 20. 20 0,01 961-161 961-261 961-361

FH 50. 50 0,01 961-161 961-261 961-361

FH 100. 100 0,05 961-161 961-261 961-361

FH 200. 200 0,1 961-161 961-261 961-361

FH 500. 500 0,1 961-161 961-261 961-361

Digital force gauge FH-S

Universal digital force gauges for tension and compression tests

with integrated measuring cell and RS-232 data interface

Features

•Turnable display with backlight

• Can be mounted on all test stands

•Digital force gauge with internal sensor

•Data interface RS-232, included

• Standard attachments: as shown below,

extension rod: 90 mm

• Delivered in a hard carrying case

•Selectable measuring units: N, lb, kg •Peak-Hold function to capture peaks (measure-

ment result will be “frozen” for a short time) or

Track function mode for a continuous measure-

ment indication (period of time approx. 10 s)

•Function to set limits, programming of Max./

Min., in pull and push direction, with output

of acousitc and optical signal. Ideal mode for

efficient and accurate testing of standard parts

•Auto-Power-Off

STANDARD

•Internal memory for up to 10 measurements

•Mini Statistics Kit: calculates the average

result from up to ten stored single results,

min., max., n

Technical data

•High resolution: up to 10,000 points

(total measuring range)

•Internal measuring frequency: 2000 Hz

•Precision: 0,5 % of [Max]

•Overload protection: 150 % of [Max]

•Dimensions WxDxH 66x36x230 mm

•Thread: M6 •Rechargeable battery pack integrated,

standard, operating time up to 12 h without

backlight, charging time approx. 4 h

•Net weight approx. 0,64 kg

Accessories

•Relais module, serves to amplify the output

signal of the dynamometer to control direct

actions, AFH-02

•Force-time data transfer software for

graphical representation on the PC and data

transfer to Microsoft Excel,

AFH FAST •Force-displacement data transfer software

with graphic display of the measurement

process, AFH FD

•Thermal printer, YKB-01N

• Standard attachments, AC 43

•Further accessory see www. .eu and

page 26 et seqq.


FH-S X-SENSORS GmbH


http://www.sauter.eu/



Adjusting program (CAL):

For quick setting of the balance’s accuracy.

External adjusting weight required.

Calibration block:

standard for adjusting or correcting

the measuring device.

Peak hold function:

capturing a peak value within a

measuring process.

Scan mode:

continuous capture and display

of measurements.

Push and Pull:

the measuring device can capture tension

and compression forces.

Length measurement:

captures the geometric dimensions of

a test object or the movement during

a test process.

Focus function:

increases the measuring accuracy of a

device within a defined measuring range.

Internal memory:

to save measurements

in the device memory.

Data interface RS-232:

bidirectional, for connection

of printer and PC.

Data interface USB:

To connect the balance to a printer,

PC or other peripheral devices.

Data interface Infrared:

To transfer data from the balance to a

printer, PC or other peripheral devices.

Control outputs

(optocoupler, digital I/O):

to connect relays, signal lamps, valves, etc.

Analogue interface:

to connect a suitable peripheral device for

analogue processing of the measurements.

Statistics:

using the saved values, the device

calculates statistical data, such as

average value, standard deviation etc.

PC Software:

to transfer the measurements from

the device to a PC.

Printer:

a printer can be connected to the

device to print out the measurements.

GLP/ISO record keeping:

of measurements with date, time and

serial number. Only with printers.

Measuring units:

Weighing units can be switched to

e.g. non-metric at the touch of a key.

Please refer to website for more details.

Measuring with tolerance range:

Upper and lower limiting can

be programmed individually,

e.g. for sorting and dosing.

ZERO:

Resets the display to “0”.

Battery operation:

Ready for battery operation.

The battery type is specified

for each device.

Rechargeable battery pack:

rechargeable set.

Mains adapter:

230V/50Hz in standard version for EU.

On request GB, AUS or USA version

available.

Power supply:

Integrated, 230V/50Hz in EU.

More standards e.g. GB, AUS

or USA on request.

Motorised drive:

The mechanical movement is carried out

by a motorised drive.

Fast-Move:

the total length of travel can be covered

by a single lever movement.

ISO Calibration:

The time required for ISO calibration

is shown in days in the pictogram.

Package shipment:

The time required for internal

shipping preparations is shown

in days in the pictogram.

Pallet shipment:

The time required for internal

shipping preparations is shown

in days in the pictogram.

Warranty:

The warranty period is shown

in the pictogram.

Pictograms:


FH-S X-SENSORS GmbH


GmbH • Ziegelei 1 • 72336 Balingen • Germany • Telephone + 49-7433-9933-0 • Fax + 49-7433-9933-149 • www. -sohn.com • info@ .eu AFH_02-BA-e-1410

User's manual

AFH-02

AFH-02 relay module

Machine control by means of control outputs

Features

•In order to control the machine operations with the use of a dynamometer it is necessary to process the dynamometer control signals in terms of the machine control system.

•As the output signals of FH dynamometer are too low for direct control of the

operations, a relay module is used for their processing which allows for

operation with constant/variable voltage from 20 to 35 V.

•The dynamometers of FH series of company make it possible after setting

the values in the device to control various outputs. It is possible to control 3

outputs. 1. the measurement result is lower than the lower limit value (LoLt option in FH dynamometer menu), 2. the measurement result is higher than the upper limit (HILt option in FH dynamometer menu), 3. the measurement result exceeds Stop value (StoP option in FH dynamometer menu).

• The system of the relay module connections allows setting 4 control options: - value below the lower limit,

- value is OK (between the lower and upper limit), - value above the upper limit, - exceeding of the Stop value.

•The relay module is intended to be fixed on 35/15 mm rails which conform

to DIN 50022 standard as well as for universal assembly in the control cabinet.

•The relay module is equipped in 4 relays, each with one potential-free

change-over.

•The dynamometer is connected to the relay module with the use of SUB-D plug-in socket .

• The scope of delivery : a relay module, a connection cable ca. 1.5m long.

Assignment of terminals

Break contact Common potential- free contact

Make contact

Lower limit value

Ö1 C1 S1

OK Ö2 C2 S2

Upper limit value

Ö3 C3 S3

Stop Ö4 C4 S4

Technical data

Input voltage Relay connection voltage Dimensions

from 20 to 35 V, constant/variable voltage 250 V/10 A 90 × 77 × 41 mm

Compatibility with the equipment software of FS dynamometer from S 5.28 version with full range of functions, below with limited operation (no useful 'Stop' signal).


FH-S X-SENSORS GmbH


http://www.kern-sohn.com/




mailto:[email protected]



Thank you for buying a force gauge. We hope you are

pleased with your high quality force gauge with its big

functional range. If you have any queries, wishes or helpful

suggestions, do not hesitate to call our service number.

„Sensor Inside“ means the measuring cell is inside the

housing.

1. Included in delivery

- FH incl. rechargeable battery

- Carrying Case

- Charger

- Standard Attachments as shown below,

5 pcs M3 x 8 screws

Important annotation:

By pressing the RESET key (on the right side of housing,

see illustration on the left), individual settings and

memorised values can be re-set or erased, in example for

a new start of the instrument after an operating error.

Data in mm

2. Working Conditions

10°C to 30°C / 15% up to 80% humidity

3. Electrical Power Supply

Either by rechargeable battery or current power supply

Current power supply:

are charged

- Connection by power adapter

- Rechargeable batteries

simultaneously

Rechargeable battery pack for mobile applications:

- Type: Ni 8.4V / 600 mAh

- Charging time: approx. 1 hour

Instruction Manual

FH

Sensor

Inside

Adaptersockel

Re Set Taste

Set

LCD

Grenzwert Anzeige

RS 232

Kraftaufnehmer

Power plug

Reset button

Se

Display

Pilot lamp

RS-232 port

Force Sensor

FH_SI-BA-e-1317 1


FH-S X-SENSORS GmbH


Instruction Manual

FH

4. Technical Data

- Accuracy: ± 0,5 % of Capacity (measuring range)

- Data Sampling Rate: 2.000 Hz

- Weight: 640 g

5. Operation

Display

(1) Measuring Result

(2) Measuring Units

(3) Activation of PRINT Function

(4) Indication of power charging status

(5) PEAK or AUTO-PEAK Mode

(6) Average value of stored peak values

(7) Force direction

(8) Occupancy of storing spaces

(9) AVERAGE- or Saving Mode

Operation keys

ON / OFF:

ON / OFF key

(For ON, press 1 sec.)

UNIT:

- Press shortly:

- Press for 2 sec.:

Select unit:

N, kg or lb

Display return

ZERO:

Three functions:

- Zeros the measuring result (Tara function)

- Cleans the peak value (in Peak mode)

- Saves a setting (in SET mode)

SET:

- 1 x Press: Upper Limit [HidT / Hi Lt]. To

change press: ▲ or ▼ (see section

High/Low Limit function)

- 1 x Press: Lower Limit [LodT]. To change

press ▲ or ▼ (see section High/Low Limit

function)

- 1 x Press: Minimum limit to save peak values

in the instrument’s memory. [LE.SET / Lo

Pe]. Please see section „Min Limit Peak

Save“. To change press: ▲ or

▼ (Only active in „Peak-Mode“) (see

section min. limit peak save)

- 1 x Press: Sets the Auto-STOP force value

that stops the movement of a test stand.

Adjustment of the force value. To change

press: ▲ or ▼ (only active in „Battery-

Mode“)

1 x Press: Auto-OFF Function. Turns the

instrument off after a here defined time

period in sec. [P.OFF]. To change press: ▲

or ▼ (Only active in „Battery-Mode“)

- 1 x Press: Peak-Freeze-Time [PE.2E / A.PE /

HoldT]: Time period (in sec.) in which a

peak value is being shown in the display in

sec. To change press: ▲ or ▼

- 1 x Press: Data Transfer [rS232] to PC (PC) or

to the printer (Print) or (in version U 5.1) to

the test stand

- PC: Pressing SET once: Saves the Settings

- PRINT: Pressing SET twice: sending data to the printer

- STAND: Pressing SET three times: sending a signal to

the Test Stand to stop its movement (in version U 5.1)

BACK LIGHT:

Hi Lt

Lo dT

Lo Pe

P.OFF

HoldT

rS232

StoP

FH_SI-BA-e-1317 2


FH-S X-SENSORS GmbH


- Track mode (continuous measurement)

- Peak mode (capture of maximum values)

- Auto-Peak mode, same as Peak-mode, only

without the „Min limit peak save“ function

MEMORY:

Saves the peak values to calculate the average

value (please see section “Memory mode”

DELETE Function

Deletes stored peak values (only in „Memory

mode“ active)

PRINT:

Sends the stored peak values to a PC or Printer

(please see section „Data Output”)

High / Low limit function

LEDs to display OK / NOT OK Tests

▼

●

▲

Lower than lower limit

Lights if the STOP value is reached

Higher than highest limit

This function allows efficient testing of OK / NOT OK’S

measurements of similar or identical testing objects.

A lower and an upper limit value can be defined. The

instrument compares the individual measuring results with

these limit values and shows the OK or NOT OK result by

green or red light diode and by sound.

To set these limit values, please see the SET Menu in

section „Operating keys“.

Measurement (Track Modus)

Display (1) shows the continuous force in a defined

direction (6)

To zero the display, press:

Instruction Manual

FH

PEAK: Peak-Hold Function (Peak Mode)

Please press:

Three functions available:

Auto-Peak-Hold-Function (Auto-Peak Mode)

Please press:

Min. limit peak function to activate storage of

measurements

This function allows to eliminate unwanted „Pre-Peak

values“ that are lower than the main peak value (Fp). The

“Min limit peak save” value (Fo) takes care, that these

“Pre-Peak values” are not saved.

The „Min limit peak save“ function is only possible in Peak-

Mode.

To set this Min limit value, please see the SET Menu in

section „Operating keys“.

Memory mode and average value (from up to 10 peak

values)

Saving peak values in the instrument

Activating the „AUTO PEAK Function“ by PEAK key

Deactivating the „Average Function“ by MEMORY key

Now, all peak values are stored automatically in the

instrument

To browse through the stored values, please use the ▲

or ▼ keys. (The values will be shown in the upper

display segment)

By pressing the MEMORY key, the average value of the

stored peak values can be shown (in the upper display

segment)

To delete every stored value, press the▼-key in the

AVERAGE-Mode

FH_SI-BA-e-1317 3


FH-S X-SENSORS GmbH


Instruction Manual

FH

6. Configuration of RS 232

SUB-D 9pm

FH_SI-BA-e-1317 4

Pin Signal Illustration

2 TxD Output signal

3 RxD Input signal

5 GND Ground

6 +1.6 to + 2 V Over upper limit

7 +1.6 to + 2 V Lower than lower limit

8 +1.6 to + 2 V OK

6.1 Output Protocol

RS-232 Parameter

Baud rate: 9600

Data-Bit: 8

Parity: none

Stop-Bit: 1

The measured value is requested by the PC by the ASCII

Sign “9”.

The measured value that comes from the instrument has

this format:

e.g. 0011.70 means -11,70 Newton, if

Newton is the selected unit

||-----|

| | > the other 6 places describe the

measured value as ASCII-Signs

| > the first place describes the

direction of the force (0 = minus = Pressure;

1 = plus = Tension)

or: 1021.15 means +21,15 N (Tension)

| > the first place describes the

direction of the force (0 = minus = Pressure;

1 = plus = Tension)

or: 1021.15 means +21,15 N (Tension)

7. Warning

Intended use

The instrument you have acquired serves to determine the

measuring value of the material to be measured. It is

intended to be used as a “non-automatic“ instrument, i.e.

the material to be measured is manually and carefully

attached at the instrument. The measuring value can be

read off after a stable measurement value has been

obtained.

Inappropriate use

Do not use the instrument for medical measurements. In

the event that small quantities are removed or added to the

material to be measured, incorrect measuring results can

be displayed due to the “stability compensation“ in the

instrument. (Example: Slow draining off of liquid from a

container suspended from the instrument). Do not attach a

continuous load. This can damage the measuring unit as

well as the parts, relevant to safety.

Prevent jolts, torsion and oscillation (e.g. by appending

slopingly) of all kinds. Be sure to prevent overloading the

instrument in excess of the stated maximum load (max.),

minus any tare weight that may possibly exist. This could

damage the instrument (risk of breakage).

Important:

•Always make sure that there are no people or materials

below the load that could be injured or damaged!

•The instrument is not suitable for measuring people. Do

not use as baby scales!

•The instrument does not comply with the medical product

law (MPG).

Never operate the instrument in hazardous locations. The

series design is not explosion-proof. Structural alterations

may not be made to the instrument. This can lead to

incorrect measuring results, faults concerning safety

regulations as well as to destruction of the instrument. The

instrument may only be used in compliance with the

described guidelines. Varying areas of application/ planned

use must be approved by in writing.

Guarantee

The guarantee is not valid in following cases:

•Non-observation of our guidelines in the operating

instructions

• Use outside the described applications

• Alteration to or opening of the device

• Mechanical damage and damage caused by media,

liquids

• Natural wear and tear

• Inappropriate erection or electric installation

• Overloading of the measuring equipment


FH-S X-SENSORS GmbH


Instruction Manual

FH

Monitoring the test substances

The metrology features of the instrument and any possible

available adjusting weight must be checked at regular

intervals within the scope of quality assurance.

For this purpose, the answerable user must define a

suitable interval as well as the nature and scope of this

check. Information is available on the home page

(www.SensorShop.com) with regard to the monitoring of

instrument test substances and the test weights required

for this. Test weights and instruments can be adjusted

quickly and at a reasonable price in ’s accredited DKD

calibration laboratory (return to national normal).

Fundamental safety information

Do not use the hanging instrument to transport loads.

Prevent jolts, torsion and oscillation (e.g. by appending

slopingly) of all kinds.

Never use the hanging instrument over the maximum

permitted weight (!! Danger of breaking!!).

Always make sure that there are no living beings or

materials below the load that could be injured or damaged.

The hanging electronic instruments from the instrument

are only suitable for hand-held use or use in a test stand.

They are not suitable for hanging from a mechanical hook,

e.g. a crane hook.

Observe the information in the operating instructions

Please read the operating instructions carefully before

erecting

and commissioning, even if you already have experience

with instruments.

Staff training

The device may only be operated and looked after by

trained members of staff.

8. CE Declaration of Conformity

FH_SI-BA-e-1317 5


FH-S X-SENSORS GmbH


Instruction Manual

FH

FH Adjustment Procedure

FH_SI-BA-e-1317 6

1 Start the

instrument

Press ON/OFF The green

light is on

2 Enter the

adjustment

procedure

Directly after pressing

ON/OFF, press PEAK

and PRINT together for

more times and very

short intervals until the

red light is on.

The lower

red light is

on

3 Instrument

Type

Press SET

Directly after pressing

PEAK + PRINT

XXX N is

shown

a (Back to the

normal

mode ???)

(If you are in the

operation mode again,

the instrument has to be

shut off. Start again with

1. Eventually pressing

the buttons faster)

4 Select the

instrument

type

Press ▼▲ The

correspondi

ng value to

the instr.

appears in

the display

5 Save

instrument

type

Press SET

6 Enter the

adjustment

sequence

Press MEMORY The upper

red light is

on

7 Choose the

adjustment

weight

Press UNIT and

with▼▲ specify the

calibration weight in

Newton (X kg * 9,81)

The weight

is written in

the display

8 Save the

adjustment

weight

Press SET and UNIT

simultaneously

9 Attach the

weight to the

instrument

(by hanging)

Press ZERO The

instrument

changes to

operation

mode.

Adjustment

procedure is

finished


FH-S X-SENSORS GmbH


FH Schnittstellenbeschreibung

17.05.2016 FH-SCHNITTSTELLEN BESCHREIBUNG DP

Senden vom PC Gerät

ASCⅡ Dezimal Hex

2 50 32 Anzeige auf „Null“ stellen

3 51 33 Einheit umstellen auf "KN"

4 52 34 Einheit umstellen auf "TF"

5 53 35 Einheit umstellen auf "KLBF"

6 54 36 Schaltet Gerät in den Track Modus

7 55 37 Schaltet Gerät in den Peak Modus

9 57 39 Gerät sendet aktuellen wert an den PC

Sendeformat

1. bei der Einheit kN sieht das Daten Byte folgender maßen aus:

bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 bit 7

Kraft-

richtung

data 1

data 2

Dezimal

punkt

data 3

data 4

data 5

Bit 1 Kraftrichtung

1: Kraftrichtung “Zug”

0: Kraftrichtung “Druck”

Wenn das Gerät 0,005 kN in “Zugrichtung misst sieht

das Datenbyte folgender maßen aus:


1 0 0 . 0 0 5

Wenn das Gerät 0,005 kN in “Druckrichtung misst sieht das Datenbyte folgender maßen

aus:


0 0 0 . 0 0 5

- Baudrate: 9600 - Daten-Bit: 8 - Parität: keine - Stop-Bit: 1

Beispiel:

Der Messwert wird durch das ASCII-Zeichen „9“ angefordert.

Der zurückgelieferte Messwert sieht folgendermaßen aus:

bedeutet -11,70 Newton, wenn Newton als Einheit eingestellt ist z.B. 0011.70

||-----|

| | >

| >

die restlichen 6 Stellen beschreiben den Messwert als ASCII-Zeichenkette

erstes Zeichen beschreibt das Vorzeichen (0 = minus = Druck; 1 = plus = Zug)

oder: 1021.15 bedeutet +21,15 N (Zugkraft)


FH-S X-SENSORS GmbH


FH Data Connection protocol


Senden vom PC Device

ASCⅡ decimal hex

3 50 32 Set the unit to “zero”

3 51 33 make the unit as "KN"

4 52 34 make the unit as "TF"

5 53 35 make the unit as "KLBF"

6 54 36 make the gauge on the tracking mode

7 55 37 make the gauge on the peak mode

9 57 39 send the value data to pc

format of sending

1. when the unit is " KN", the format sending as:


bit of

force

direction

data 1

data 2

point

data 3

data 4

data 5

bit of force direction

1: force direction is pull 0:

force direction is press

if the pull force is 0.005KN, and the unit is "KN" the

format of sending is:


1 0 0 . 0 0 5

if the pressure is 0.005KN, and the unit is "KN"

the format of sending is:


0 0 0 . 0 0 5

- Baudrate: 9600 - Data-Bit: 8 - Parity: none - Stop-Bit: 1

Example: The measured value requested through sending ASCII-sign „9“ from the PC to the force gauge

The requested data looks like:

z.B. 0011.70 means -11.70 N if the force gauge is set to unit Newton

||-----|

| | > the other 6 digits are the measured value in ASCII

| > the first sign in the byte is the pre sign (0 = minus = comprehension;

1 = plus = Tension)

or: 1021.15 means +21,15 N


FH-S X-SENSORS GmbH


Kommandos zum steuern der Prüfstände


Commands to manage the test stands

TVM-N Startet Bewegung “AUF” ASCII 7c

TVM-N Startet Bewegung “AB” ASCII 7d

TVM-N STOP ASCII 7e

TVM-N Start movement UP ASCII 7c

TVM-N Start movement DOWN ASCII 7d

TVM-N STOP ASCII 7e


FH-S X-SENSORS GmbH


fh-s•thread:m6 •rechargeable battery pack integrated, standard, operating time up to 12 h...

Documents