february 1, 2019 - city of anderson sc · 2019-02-14 · february 1, 2019 erica m. craft city of...

February 1, 2019

Erica M. Craft City of Anderson 601 S. Main Street Anderson, South Carolina

Re: Asbestos Survey Update of 1114 White Street D&F Job Number: 013707.00

On January 15, 2019 Davis & Floyd, Inc. conducted an asbestos survey update at the Single-Family Residence, located at 1114 White Street, Anderson, South Carolina. The residence was not occupied at the time of our survey.

The purpose of the survey was to identify suspect asbestos containing materials (ACM’s) that may be present in the building. Sampling and analysis conforms to the amendments of South Carolina Department of Health and Environmental Control (SCDHEC) Regulation 61-86.1 “Standards of Performance for Asbestos Projects”, latest edition.

The Environmental Protection Agency (EPA) and the South Carolina Department of Health and Environmental Control (SCDHEC) define materials as asbestos-containing if an asbestos content of greater than one percent (>1%) is detected in a representative sample. Asbestos, in concentrations greater than one percent (>1%), was identified in some of the samples collected. The chimney sealer was presumed asbestos containing material (PACM). Field conditions and quantities in this report should be verified prior to performing any asbestos removals. The asbestos survey report is attached to this letter.

Please do not hesitate to contact us should you have any questions regarding this report at (864)229-5211 or [email protected]

Very truly yours,

DAVIS & FLOYD

Mark H. Stevens Sr. Environmental Designer

mstevens

Mark's Signature

Asbestos Survey Update for

City of Anderson Final Report – January, 2019

1114 White Street

Single-Family Residence

D&F Job No. 013707.00

PREPARED FOR:

Erica M. Craft

City of Anderson

401 South Main Street

Anderson, SC 29624

PREPARED BY:

Davis & Floyd, Inc.

1319 Highway 72/221 E

Greenwood, South Carolina 29649

(864) 229-5211

√ Asbestos Present (Requires Project Design)

Asbestos Survey Update Davis & Floyd, Inc. 1114 White St D&F Job No. 013707.00 Jan, 2019

Table of Contents

Section 1.0 Asbestos Survey Report………………………………………………………2

1.1 Introduction .......................................................................................................................................................... 3

1.2 Homogeneous Material Assessment………………………………………………………………………………………………………4

1.3 Bulk Sample Results…………………………………………………………………………………………………………………………….5

1.4 Regulatory Requirements…………………………………………………………………………………………………………………….6

1.5 Definitions………………………………………………………………………………………………………………………………………….6

Section 2.0 Laboratory Analysis Reports.............................................. 7

Section 3.0 Applicable Licenses ........................................................ 13

Section 4.0 Photographs ................................................................... 15

Appendix 'A'……………………………………………………………………………………………………….…25

2018 Michael Baker International Asbestos Survey Report


Section 1.0 Asbestos Survey Report

Sub-Section 1.1 Introduction

On January 15, 2019, Davis & Floyd, Inc. conducted an asbestos building inspection at a Single-Family Residence located at 1114 White Street in Anderson, South Carolina. The purpose of this inspection was to update a previous asbestos survey report by Michael Baker International (September 5, 2018), and to perform supplemental bulk sampling and analysis to conform with the South Carolina Department of Health and Environmental Control (SCDHEC) Regulation 61-86.1 Standards of Performance for Asbestos Projects effective May 27, 2011, for the purpose of demolition.

Background

Davis & Floyd, Inc. reviewed the asbestos survey report of the structure prepared by Michael Baker International, dated September 5, 2018. A copy of this report is presented in Appendix ‘A’. The report includes the laboratory analysis of approximately twenty-three (23) bulk samples from various materials throughout the structure:

Wall & ceiling Board Vinyl Floor Sheeting and Floor Adhesive (yellow block) Vinyl Floor Sheeting and Floor Adhesive (green flower) Vinyl Floor Tile and Floor Adhesive (9 x 9 tan) Vinyl Floor Sheeting and Floor Adhesive (9 x 9 white) Vinyl Floor Sheeting and Floor Adhesive (wood pattern) Wall Adhesive Vinyl Floor Sheeting and Floor Adhesive (yellow stone) Window Caulking Cement Siding (transite) Asphaltic Roofing (gray shingles) Paint Sealer (silver) Siding and Roofing Material (tar paper) Stucco (on ceiling board)

Additional Bulk Sample Analysis

Additional bulk samples were collected by Davis & Floyd, Inc. to meet the requirement of the SCDHEC Regulation 61-86.1 Standards of Performance for Asbestos Projects effective May 27, 2011, from accessible suspect materials within the residence and the samples were subsequently analyzed for asbestos content by an accredited laboratory. The suspect materials observed include:

Gypsum board Joint compound Vinyl Floor Sheeting and Floor Adhesive (yellow block) Wall Adhesive Window Caulking Asphaltic Roofing (gray shingles) Paint Sealer (silver) Siding and Roofing Material (tar paper) Stucco (on ceiling board) Chimney Sealer @ Roof Penetration (presumed asbestos) PACM

Asbestos Survey Update Davis & Floyd, Inc. 1114 White St D&F Job No. 013707.00

Jan, 2019

The Environmental Protection Agency (EPA) and the South Carolina Department of Health and Environmental Control (SCDHEC), define materials as asbestos containing if an asbestos content of greater than one percent (>1%) is detected in a representative sample. A total of Sixteen (16) Homogeneous Materials (Areas) were identified throughout the residence. The following table identifies a summary of the asbestos containing materials (ACM’s) as a result of the samples collected:

Sub-Section 1.2 Identified Asbestos Containing Materials (ACM):

Homo. ID (# of

samples) Homogeneous Material (Category)1 Overall

Condition 2

Potential for Further

Disturbance 3 HM-1,HM-13 (5) Gyp. Bd. w/ Jt. Comp (stucco) - 3,800 s.f. F-Poor High

HM-3 (2) Vinyl Floor Sheeting – 255 s.f. Miscellaneous NF-Good LowHM-4 (2) Vinyl Floor Tile 9 x 9 – 585 s.f. Miscellaneous NF-Good LowHM-5 (2) Vinyl Floor Sheeting – 120 s.f. Miscellaneous NF-Good LowHM-7 (2) Vinyl Floor Sheeting – 42 s.f. Miscellaneous NF-Good LowHM-9 (2) Cement Siding – 2,250 s.f. Miscellaneous NF-Good High

HM-1,HM-13 Contaminated Floor Area - 2,250 s.f. Miscellaneous F-Poor HighHM-16 Chimney Sealer (PACM) - 50 s.f. Misc. (Cat. II) NF-Good Low

1-Homogeneous Material (Category): Surf. -Surfacing; Misc.-Miscellaneous; TSI-Thermal System Insulation

2-Overall Condition: (F) - Friable – Good, Fair, Poor; (NF)-Non-Friable – Good, Fair, Poor

3-Potential for Further Disturbance: Low, Medium, High

Category I – Nonfriable asbestos or nonfriable asbestos containing packing, gaskets, and resilient floor covering; and asphalt roofing products containing greater than one present (1%) asbestos as determined using the method specified in 40 CFR Part 763, Appendix E, Subpart E, or an accepted equivalent.

Category II – Any material that cannot when dry, be crumbled, pulverized, or reduced to powder by the forces expected to act upon it in the course of demolition or renovation operations, excluding Category I nonfriable ACM and containing greater than one percent (1%) asbestos as determined using the methods specified in 40 CFR Part 763, Appendix E, Subpart E, or an accepted equivalent.

Sub-Section 1.3 Bulk Sample Results

Representative samples of each suspected homogenous material (area) were randomly collected from locations throughout the facility. According to 40 CFR 763.87, the Environmental Protection Agency defines a material to qualify as “asbestos-containing material” if any sample of the suspect material is found to contain asbestos in concentrations greater than one percent (>1%).

In addition, the South Carolina Department of Health and Environmental Control (SCDHEC) Regulation 61.86.1, “Standards of Performance for Asbestos Projects” (May 27, 2011), Section VI-Asbestos Building Inspection Requirements, D. Sampling, paragraph 2.0 states:

1. A licensed asbestos inspector shall collect, in a statistically random manner, atleast three bulk samples from each homogeneous material of TSI and anymiscellaneous material that is not assumed to be ACM. In accordance with ASTME2356, and any subsequent amendments and editions, negative results for non-

Surfacing


friable organically bound materials (NOB), such as flooring, mastics and roofing shall be verified with at least one TEM analysis.

To meet this requirement, one sample of each non-friable organically bound material (NOB) was sent to an independent lab for Transmission Electron Microscopy (TEM) analysis. The reports from the independent laboratory (licensed to perform TEM analysis) is also included in this report. During the laboratory analysis process, once a sample in a homogeneous area is found to be asbestos containing material (ACM), the remainder of the samples in that homogeneous area may not be analyzed by the laboratory (TEM or PLM).

Sub-Section 1.4 Regulatory Requirements

Confirmed asbestos containing materials (ACM’s) should not be disturbed by untrained personnel. Damaged or ACM in poor condition should be removed or repaired by trained asbestos workers. Confirmed ACM should be periodically inspected.

Before starting a renovation/demolition project, which involves disturbing the ACM, the ACM should be removed by a licensed asbestos abatement contractor. A copy of this report must be submitted to SCDHEC, along with the demolition license application, ten (10) weekdays prior to renovation / demolition activities.

Any activity involving the ACM should be in compliance with South Carolina Department of Health and Environmental Control Regulation 61-86.1, “Standards of Performance for Asbestos Projects”, latest edition.

Category I and Category II non-friable mastics, glues, and adhesives ACM that is not friable or in poor condition may be left in place during demolition.

Sub-Section 1.5 Definitions (R 61-86.1)

Definitions in SCDHEC Regulation 61-86.1 “Standards of Performance for Asbestos Projects” may be viewed at the following web address: https://live-sc-dhec.pantheonsite.io/sites/default/files/media/document/R.61-86.1.pdf


Section 2.0 Laboratory Analysis Reports

EMSL Analytical, Inc.10801 Southern Loop Blvd Pineville, NC 28134

Tel/Fax: (704) 525-2205 / (704) 525-2382

http://www.EMSL.com / [email protected]

411900575EMSL Order:

Customer ID: DAVI57

Customer PO: 01370700

Project ID:

Attention: Phone:Mark Stevens (864) 229-5211

Fax:Davis & Floyd (864) 229-7119

Received Date:P.O. Drawer 428 01/18/2019 4:51 PM

Analysis Date:Greenwood, SC 29648 01/22/2019

Collected Date:

Project: 01370700

Test Report: Asbestos Analysis of Bulk Materials via EPA 600/R-93/116 Method using Polarized

Light Microscopy

Sample Description Appearance % Fibrous % Non-Fibrous

Non-Asbestos Asbestos

% Type

1114-01

411900575-0001

None DetectedNon-fibrous (Other)90%Cellulose10%Gray

Non-Fibrous

Homogeneous

Gypsum Board

1114-02

411900575-0002

None DetectedNon-fibrous (Other)90%Cellulose10%Gray

Fibrous

Homogeneous

Gypsum Board

1114-03

411900575-0003

None DetectedNon-fibrous (Other)90%Cellulose10%Tan

Fibrous

Homogeneous

Gypsum Board

1114-04

411900575-0004

2% ChrysotileCa Carbonate

Non-fibrous (Other)

30%

68%

Tan

Non-Fibrous

Homogeneous

Joint Compound

1114-05

411900575-0005

Positive Stop (Not Analyzed)Joint Compound

1114-06

411900575-0006

Positive Stop (Not Analyzed)Joint Compound

1114-07

411900575-0007

None DetectedCa Carbonate

Non-fibrous (Other)

10%

85%

Cellulose

Glass

3%

2%

Gray/Tan

Fibrous

Heterogeneous

Vinyl Floor Sheeting

(Yellow)

1114-08

411900575-0008

None DetectedNon-fibrous (Other)99%Cellulose1%Brown

Non-Fibrous

Homogeneous

Wall Adhesive

1114-09

411900575-0009


Non-fibrous (Other)

25%

74%

Fibrous (Other)1%Gray/White

Non-Fibrous

Homogeneous

Window Caulking

1114-10

411900575-0010

None DetectedQuartz

Ca Carbonate

Non-fibrous (Other)

10%

5%

70%

Cellulose15%White/Black

Fibrous

Heterogeneous

Asphaltic Roofing

(Gray)

1114-11

411900575-0011


Non-fibrous (Other)

8%

90%

Cellulose

Fibrous (Other)

1%

1%

Gray/Tan/White

Non-Fibrous

Homogeneous

Paint Sealer (Silver)

1114-12

411900575-0012

None DetectedNon-fibrous (Other)33%Cellulose

Synthetic

65%

2%

Black

Non-Fibrous

Homogeneous

Tar Paper

1114-13

411900575-0013

3% ChrysotileCa Carbonate

Mica

Non-fibrous (Other)

20%

5%

72%

Tan/White

Non-Fibrous

Homogeneous

Stucco

Initial report from: 01/22/2019 15:56:34

Page 1 of 2ASB_PLM_0008_0001 - 1.78 Printed: 1/22/2019 3:56 PM


Tel/Fax: (704) 525-2205 / (704) 525-2382



Customer ID: DAVI57


Project ID:

Analyst(s)

Eric Loomis (10)

Matthew McDonald (1)

Lee Plumley, Laboratory Manager

or Other Approved Signatory

EMSL maintains liability limited to cost of analysis . The above analyses were performed in general compliance with Appendix E to Subpart E of 40 CFR (previously EPA 600/M4-82-020 "Interim

Method"), but augmented with procedures outlined in the 1993 ("final") version of the method. This report relates only to the samples reported above, and may not be reproduced, except in full, without

written approval by EMSL. EMSL bears no responsibility for sample collection activities or analytical method limitations . Interpretation and use of test results are the responsibility of the client. All

samples received in acceptable condition unless otherwise noted. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST or any agency of

the federal government. EMSL recommends gravimetric reduction for all non -friable organically bound materials prior to analysis. Estimation of uncertainty is available on request.

Samples analyzed by EMSL Analytical, Inc. Pineville, NC NVLAP Lab Code 200841-0, VA 3333 00312




Tel/Fax: (704) 525-2205 / (704) 525-2382


EMSL Order: 411900575

Customer ID: DAVI57


Project ID:

Attention: Mark Stevens Phone: (864) 229-5211

Davis & Floyd Fax: (864) 229-7119

P.O. Drawer 428 Received Date: 01/18/2019 4:51 PM

Greenwood, SC 29648 Analysis Date: 01/22/2019

Collected Date:

01370700Project:

Test Report: Asbestos Analysis of Non-Friable Organically Bound Materials by TEM via

EPA/600/R-93/116 Section 2.5.5.1

Sample ID Description Appearance % Matrix Material % Non-Asbestos Fibers Asbestos Types

1114-07

411900575-0014

Vinyl Floor Sheeting

(Yellow)

Brown/Green/Beige

Non-Fibrous

Heterogeneous

100.0 None No Asbestos DetectedOther

1114-08

411900575-0015

Wall Adhesive Brown

Non-Fibrous

Heterogeneous


1114-09

411900575-0016

Window Caulking Gray

Non-Fibrous

Heterogeneous

99.69 Fibrous_Other No Asbestos Detected0.31Other

1114-10

411900575-0017

Asphaltic Roofing (Gray) Gray/Black

Non-Fibrous

Heterogeneous


1114-12

411900575-0018

Tar Paper Gray/Black

Non-Fibrous

Heterogeneous


Analyst(s)

Aaron Hartley (5) Lee Plumley, Laboratory Manager

or other approved signatory

This laboratory is not responsible for % asbestos in total sample when the residue only is submitted for analysis. The above report relates only to the items tested. This report may not be reproduced,

except in full, without written approval by EMSL Analytical , Inc. Samples received in good condition unless otherwise noted. Unless requested by the client, building materials manufactured with

multiple layers (i.e. linoleum, wallboard, etc.) are reported as a single sample.

Samples analyzed by EMSL Analytical, Inc. Pineville, NC


ASB_PLMEPANOB_0012_0002 Printed 1/23/2019 8:48:46AM Page 1 of 1

OrderID: 411900575

Page 1 Of 2

OrderID: 411900575

Page 2 Of 2


Section 3.0 Copy of Applicable Inspector Asbestos Licenses

COPY OF APPLICABLE ASBESTOS LICENSES

Building Inspector:

___________________________Date: _____________

Mark H. Stevens Davis & Floyd, Inc. Environmental Services SCDHEC License No. ASB-22192 (exp. 11/27/19)

1-15-19

mstevens

Mark's Signature


Section 4.0 Photographs


(HM-1a) Gypsum Wallboard and (HM-1b) asbestos Joint Compound


(HM-1a & HM-1b) deteriorated asbestos Gypsum Board and Joint Compound on top of asbestos Vinyl Flooring


(HM-3) asbestos Vinyl Floor Sheeting and Mastic


(HM-4 & HM-5) asbestos Vinyl Flooring under asbestos contamination


(HM-6) non-asbestos Wall Adhesive


(HM-8) non-asbestos Window Caulking / Glazing


(HM-9) asbestos Cement Siding (transite)


(HM-13) asbestos Stucco on gypsum ceiling board


(HM-16) presumed asbestos Chimney Sealer (PACM) (HM-10) non-asbestos Asphaltic Roofing and Felt Paper Note: Chimney Sealer is a Category II non-friable material in good condition and can stay on the structure during demolition.


Appendix 'A'

2018 Michael Baker International Asbestos Survey Report

101 North Main Street | Greenville, SC 29601

Office: 864-670-2745 | Fax: 864-670-2744

Disclaimer

The information that is presented in this report reflects the conditions that were observed in the building(s) during the time frame

this inspection was conducted. Although every effort was made to identify the potential suspect building materials and components,

there is no guarantee that additional building materials in these damaged buildings are not present. Conditions may exist in the

building(s), such that inaccessible materials may only become apparent during demolition activities. If any hidden, suspicious

material is encountered, it is recommended that the material be analyzed to confirm its asbestos content.

FIGURES

TABLES

TABLE 1

ASBESTOS SURVEY MATERIAL SUMMARY

PARCEL 150-01-02-013-0000

1114 WHITE STREET, ANDERSON, SOUTH CAROLINA

Homogeneous

Material

Number

Material

Type

Material

Description

Material

LocationsFriable Sample Numbers Sample Results

Sample

Locations

Asbestos-

Containing

Material

Approximate

Quantity of

Asbestos

Condition of

Material

01 No SC-H9-01A None Detected Room 2

SC-H9-01B None Detected Room 6

SC-H9-01C None Detected Room 8

02 No SC-H9-02A None Detected Room 1



03 SC-H9-03A 15% Chrysotile Room 2 255 Square Feet Damaged

SC-H9-03B Not Analyzed Room 2

SC-H9-03C Not Analyzed Room 2

04 SC-H9-04A 2% Chrysotile Room 2 585 Square Feet Damaged



05 No SC-H9-05A 15% Chrysotile Room 6



No

Yes

Yes 120 Square Feet

Not Applicable

No Not Applicable Not Applicable

Yes

Not Applicable

Damaged

Rooms 1 - 15

Vinyl Floor

Sheeting and

Floor

Adhesive

Yellow Block with

Yellow Adhesive

Room 1

Vinyl Floor

Sheeting and

Floor

Adhesive

Green Flower

with Tan

Adhesive

Rooms 1, 2, 6,

and 7

No

Wall &

Ceiling Board

White, with

White Joint

Compound

Room 2

Wood Pattern

with Tan

Adhesive

Rooms 6 and 7Vinyl Floor

Sheeting and

Floor

Adhesive

No

Vinyl Floor

Tile and Floor

Adhesive

9" x 9" Tan with

Tan Adhesive

According to EPA, asbestos-containing material (ACM) is defined as any material containing greater than 1% asbestos using laboratory analysis or, by NESHAP,

contains less than 10% asbestos is considered positive, unless re-analyzed by PLM point count.

TABLE 1


PARCEL 150-01-02-013-0000


Homogeneous

Material

Number

Material

Type

Material

Description

Material


Sample

Locations

Asbestos-

Containing

Material

Approximate

Quantity of

Asbestos

Condition of

Material

No Not ApplicableNot ApplicableRooms 1 - 15Wall &

Ceiling Board

White, with

White Joint

Compound

06 SC-H9-06A None Detected Room 7



07 No SC-H9-07A (L) 15% Chrysotile Room 12 42 Square Feet Damaged

SC-H9-07A (FA) 2% Chrysotile Room 12

SC-H9-07B (L) Not Analyzed Room 12

SC-H9-07B (FA) Not Analyzed Room 12

SC-H9-07C (L) Not Analyzed Room 12

SC-H9-07C (FA) Not Analyzed Room 12

08 No SC-H9-08A None Detected Exterior Not Applicable Not Applicable

SC-H9-08B None Detected Exterior

SC-H9-08C None Detected Exterior

09 No SC-H9-09A 15% Chrysotile Exterior Damaged

SC-H9-09B Not Analyzed Exterior

SC-H9-09C Not Analyzed Exterior

Yes

No

Not Applicable

Yes

No Not ApplicableNo

Room 12Yellow Stone

with Tan

Adhesive

Window

Caulking

White, on

Exterior

Windows

Exterior

Vinyl Floor

Sheeting and

Floor

Adhesive

Wall

Adhesive

Exterior

Tan Rooms 7 and 12

2,250 Square

Feet

Cement

Siding

Transite Siding



TABLE 1


PARCEL 150-01-02-013-0000


Homogeneous

Material

Number

Material

Type

Material

Description

Material


Sample

Locations

Asbestos-

Containing

Material

Approximate

Quantity of

Asbestos

Condition of

Material

No Not ApplicableNot ApplicableRooms 1 - 15Wall &

Ceiling Board

White, with

White Joint

Compound

10 No SC-H9-10A None Detected Exterior Roof Not Applicable

SC-H9-10B None Detected Exterior Roof

SC-H9-10C None Detected Exterior Roof

11 No SC-H9-11A None Detected Exterior Roof Not Applicable

SC-H9-11B None Detected Exterior Roof

SC-H9-11C None Detected Exterior Roof

12 No SC-H9-12A None Detected Exterior Not Applicable

SC-H9-12B None Detected Exterior

SC-H9-12C None Detected Exterior

13 No SC-H9-13A None Detected Room 1 Not Applicable



Not Applicable

Not Applicable

No

No

No

No

Not Applicable

Not Applicable

Siding and

Roofing

Material

Tar Paper Exterior

Stucco White, on Wall

and Ceiling

Board

Rooms 1, 2, 3,

and 6

Asphaltic

Roofing

Material

Gray Shingles Exterior Roof

Paint Sealer Silver Paint Exterior Roof



TABLE 2

PAINT SURVEY SUMMARY

PARCEL 150-01-02-013-0000


Component Locations Color Substrate Condition Findings Recommendations

All painted

components

Interior and

Exterior

All Paint

Colors

All

Substrates

All

Conditions

All paint contains at least a trace of lead

and must be addressed according to

OSHA requirements for lead-containing

paint.

If impacted by renovation/demolition

activities, proper handling and/or removal

of the lead-containing paint is needed.

* The requirements of the Occupational Safety and Health Administration (OSHA) Construction Standards need to be invoked if any metal content is present in the paint that may be

affected by renovation activities. OSHA does not provide a minimum concentration criteria level for lead; however, it requires precautions and protection for workers and the working

environment be taken at any work place where an exposure to airborne metals may occur.

TABLE 3

WASTE SAMPLING VIA TCLP

PARCEL 150-01-02-013-0000


Material Type Test TypeMaterial

Description

Sample

Numbers

Sample

ResultsHazardous or Non-Hazardous

Anticipated Waste Debris from Facility TCLP (lead)Building

components SC-H9-TCLP <0.40 mg/L Non-Hazardous

According to the EPA, TCLP criteria limit for leachable lead is defined as 5 milligrams per liter (mg/L) using laboratory analysis.

ATTACHMENT A

EMSL Analytical, Inc.200 Route 130 North Cinnaminson, NJ 08077

Tel/Fax: (800) 220-3675 / (856) 786-5974



Customer ID: BAKE51

Customer PO:

Project ID:

Attention: Phone:Gary Case (412) 375-3996

Fax:Michael Baker, Jr. Inc. (412) 375-3996

Received Date:100 Airside Drive 09/10/2018 8:55 AM

Analysis Date:Moon Township, PA 15108 09/23/2018 - 09/24/2018

Collected Date:

Project: Anderson House 9


Light Microscopy



% Type

SC-H9-01A

041827347-0001

None DetectedNon-fibrous (Other)90%Cellulose10%White

Fibrous

Homogeneous

SC-H9-01B

041827347-0002


Fibrous

Homogeneous

SC-H9-02A

041827347-0003

None DetectedNon-fibrous (Other)100%Brown

Non-Fibrous

Homogeneous

SC-H9-02B

041827347-0004

None DetectedNon-fibrous (Other)100%Brown/White

Non-Fibrous

Homogeneous

SC-H9-03A

041827347-0005

15% ChrysotileNon-fibrous (Other)85%Brown/White

Fibrous

Homogeneous

SC-H9-03B

041827347-0006

Positive Stop (Not Analyzed)

SC-H9-04A

041827347-0007

2% ChrysotileNon-fibrous (Other)93%Cellulose5%Brown

Fibrous

Homogeneous

SC-H9-04B

041827347-0008


SC-H9-05A

041827347-0009

15% ChrysotileNon-fibrous (Other)85%White/Red

Fibrous

Homogeneous

SC-H9-05B

041827347-0010


SC-H9-06A

041827347-0011


Non-Fibrous

Homogeneous

SC-H9-06B

041827347-0012


Non-Fibrous

Homogeneous

SC-H9-07A-Linoleum

041827347-0013

15% ChrysotileNon-fibrous (Other)85%Tan/White

Fibrous

Homogeneous

SC-H9-07A-Mastic

041827347-0013A

2% ChrysotileNon-fibrous (Other)98%Brown/Black

Non-Fibrous

Homogeneous

SC-H9-07B-Linoleum

041827347-0014


SC-H9-07B-Mastic

041827347-0014A




EMSL Analytical, Inc.200 Route 130 North Cinnaminson, NJ 08077

Tel/Fax: (800) 220-3675 / (856) 786-5974



Customer ID: BAKE51

Customer PO:

Project ID:


Light Microscopy



% Type

SC-H9-08A

041827347-0015


Fibrous

Homogeneous

SC-H9-08B

041827347-0016


Fibrous

Homogeneous

SC-H9-09A

041827347-0017

15% ChrysotileNon-fibrous (Other)85%Gray

Fibrous

Homogeneous

SC-H9-09B

041827347-0018


SC-H9-10A

041827347-0019

None DetectedNon-fibrous (Other)80%Cellulose20%White/Black

Fibrous

Homogeneous

SC-H9-10B

041827347-0020

None DetectedNon-fibrous (Other)75%Cellulose25%White/Black

Fibrous

Homogeneous

SC-H9-11A

041827347-0021

None DetectedNon-fibrous (Other)100%Silver

Non-Fibrous

Homogeneous

SC-H9-11B

041827347-0022

None DetectedNon-fibrous (Other)97%Cellulose3%Silver

Non-Fibrous

Homogeneous

SC-H9-12A

041827347-0023

None DetectedNon-fibrous (Other)30%Cellulose70%Black

Fibrous

Homogeneous

SC-H9-12B

041827347-0024

None DetectedNon-fibrous (Other)25%Cellulose75%Black

Fibrous

Homogeneous

SC-H9-13A

041827347-0025


Fibrous

Homogeneous

SC-H9-13B

041827347-0026

None DetectedNon-fibrous (Other)92%Glass8%White

Fibrous

Homogeneous

Analyst(s)

Juli Patel (12)

Maxwell Taylor (4)

Olufunke Akintunde (6)

Benjamin Ellis, Laboratory Manager

or Other Approved Signatory

EMSL maintains liability limited to cost of analysis . The above analyses were performed in general compliance with Appendix E to Subpart E of 40 CFR (previously EPA 600/M4-82-020 "Interim

Method"), but augmented with procedures outlined in the 1993 ("final") version of the method. This report relates only to the samples reported above, and may not be reproduced, except in full, without

written approval by EMSL. EMSL bears no responsibility for sample collection activities or analytical method limitations . Interpretation and use of test results are the responsibility of the client. All

samples received in acceptable condition unless otherwise noted. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST or any agency of

the federal government. EMSL recommends gravimetric reduction for all non -friable organically bound materials prior to analysis. Estimation of uncertainty is available on request.

Samples analyzed by EMSL Analytical, Inc. Cinnaminson, NJ NVLAP Lab Code 101048-0, AIHA-LAP, LLC-IHLAP Lab 100194, NYS ELAP 10872, NJ DEP 03036, PA ID# 68-00367



ConcentrationAnalyzed RDL LeadClient SampleDescription Collected

Test Report: Toxicity Characteristic Leachate Procedure (1311/7000B)

EMSL Analytical, Inc.6340 CastlePlace Dr., Indianapolis, IN 46250Phone/Fax: (317) 803-2997 / (317) 803-3047http://www.EMSL.com [email protected]

Attn: Gary CaseMichael Baker, Jr. Inc.100 Airside DriveMoon Township, PA 15108

Received: 09/13/18 8:00 AM

Anderson Houses

Fax: (412) 375-3996Phone: (412) 269-6300

Project:

Collected:

161817911CustomerID: BAKE51CustomerPO:ProjectID:

EMSL Order:

<0.40 mg/L9/26/2018161817911-0001

0.40SC - H1 - TCLP mg/L

<0.40 mg/L9/26/2018161817911-0002


<0.40 mg/L9/26/2018161817911-0003


<0.40 mg/L9/26/2018161817911-0004


<0.40 mg/L9/26/2018161817911-0005


<0.40 mg/L9/26/2018161817911-0006


<0.40 mg/L9/26/2018161817911-0007


<0.40 mg/L9/26/2018161817911-0008


<0.40 mg/L9/26/2018161817911-0009


<0.40 mg/L9/26/2018161817911-0010


<0.40 mg/L9/26/2018161817911-0011


Page 1 of 2Test Report PB w/RDL-7.32.3 Printed: 9/26/2018 6:17:38 PM

Doug Wiegand, Laboratory Manageror other approved signatory

This report relates only to those items tested. Samples received in good condition unless otherwise noted. Quality Control Data associated with this sample set is within acceptable limits, unless otherwise notedSamples analyzed by EMSL Analytical, Inc. Indianapolis, IN

Initial report from 09/26/2018 18:17:38

http://www.EMSL.com

mailto:[email protected]

ConcentrationAnalyzed RDL LeadClient SampleDescription Collected

Test Report: Toxicity Characteristic Leachate Procedure (1311/7000B)

EMSL Analytical, Inc.6340 CastlePlace Dr., Indianapolis, IN 46250Phone/Fax: (317) 803-2997 / (317) 803-3047http://www.EMSL.com [email protected]

Attn: Gary CaseMichael Baker, Jr. Inc.100 Airside DriveMoon Township, PA 15108

Received: 09/13/18 8:00 AM

Anderson Houses

Fax: (412) 375-3996Phone: (412) 269-6300

Project:

Collected:

161817911CustomerID: BAKE51CustomerPO:ProjectID:

EMSL Order:

<0.40 mg/L9/26/2018161817911-0012


<0.40 mg/L9/26/2018161817911-0013


<0.40 mg/L9/26/2018161817911-0014


<0.40 mg/L9/26/2018161817911-0015


<0.40 mg/L9/26/2018161817911-0016


<0.40 mg/L9/26/2018161817911-0017


<0.40 mg/L9/26/2018161817911-0018


Page 2 of 2Test Report PB w/RDL-7.32.3 Printed: 9/26/2018 6:17:38 PM

Doug Wiegand, Laboratory Manageror other approved signatory

This report relates only to those items tested. Samples received in good condition unless otherwise noted. Quality Control Data associated with this sample set is within acceptable limits, unless otherwise notedSamples analyzed by EMSL Analytical, Inc. Indianapolis, IN

Initial report from 09/26/2018 18:17:38

http://www.EMSL.com

mailto:[email protected]

ATTACHMENT B

MICHAEL BAKER INTERNATIONAL, INC. – PHOTOGRAPHIC RECORD

PARCEL IDENTIFICATION: Parcel 150-01-02-013-0000

PHOTOGRAPH 1

1114 White Street

PHOTOGRAPHS BY

Michael Baker

Comments: Front of house

PHOTOGRAPH 2

1114 White Street

PHOTOGRAPHS BY

Michael Baker

Comments: Material #03 – Vinyl Floor Sheeting (Green Flower)



PHOTOGRAPH 3

1114 White Street

PHOTOGRAPHS BY

Michael Baker

Comments: Material #04 – Vinyl Floor Tile (9” x 9” Tan)

PHOTOGRAPH 4

1114 White Street

PHOTOGRAPHS BY

Michael Baker

Comments: Material #05 – Vinyl Floor Sheeting (Wooden Pattern)



PHOTOGRAPH 5

1114 White Street

PHOTOGRAPHS BY

Michael Baker

Comments: Material #07 – Vinyl Floor Sheeting and Floor Adhesive (Yellow Stone with Tan Adhesive)

PHOTOGRAPH 6

1114 White Street

PHOTOGRAPHS BY

Michael Baker

Comments: Material #09 – Cement Siding (Transite Siding)

ATTACHMENT C

AIHA Laboratory Accreditation Programs, LLC3141 Fairview Park Drive, Suite 777, Falls Church, VA 22042 USA

main +1 703-846-0736 fax +1 703-207-8558

Twitter: @AIHA_LAP_LLCR3 05/05/2015

Page 1 of 1

August 31, 2016

Laboratory ID: 100194

Oommen KappilEMSL Analytical, Inc.200 Route 130 NorthCinnaminson, NJ 08077

Dear Mr. Kappil:

Congratulations! The AIHA Laboratory Accreditation Programs (AIHA-LAP), LLC’s Analytical Accreditation Board (AAB) has approved EMSL Analytical, Inc. as an accredited Industrial Hygiene, Environmental Lead and Environmental Microbiology laboratory.

Accreditation documentation includes the IHLAP, ELLAP and EMLAP accreditation certificate, scope of accreditation document and a copy of the current AIHA-LAP, LLC license agreement (if your completed agreement is not on file at AIHA-LAP, LLC). The accreditation symbol has been designed for use by all AIHA-LAP, LLC accredited laboratories. If your laboratory chooses to use the symbol in its advertising the laboratory’s accreditation, you must complete and return the AIHA-LAP, LLC license agreement to a Laboratory Accreditation Specialist.Once submitted, an electronic copy of the accreditation symbol will be sent to you. Please inform us if your laboratory does not wish to use the symbol in advertising.

Laboratory accreditation shall be maintained by continued compliance with IHLAP, ELLAP and EMLAPrequirements (see Policy Modules 2B, 2C, 2D, and 6), which includes proficient participation in AIHA-LAP, LLC approved proficiency testing, demonstration of competency, or round robin program as indicated on the AIHA-LAP“Approved PT and Round Robin” webpage, its associated Scope/PT table, and as required in Policy Module 6, for all Fields of Testing (FoTs) for which the laboratory is accredited. An accredited laboratory that wishes to expand into a new FoT must submit an updated accreditation application to AIHA-LAP, LLC for review by the AAB.

Any changes in ownership, laboratory location, personnel, FoTs/Methods, or significant procedural changes shall be reported to AIHA-LAP, LLC in writing within twenty (20) business days of the change.

The accreditation certificate is the property of AIHA-LAP, LLC and must be returned to us should your laboratory withdraw or be removed from the IHLAP, ELLAP and EMLAP.

Again, congratulations. If you have any questions, please contact Lauren Schnack, Laboratory Accreditation Specialist, at (703) 846-0716.

Sincerely,

Cheryl O. MortonManaging Director AIHA Laboratory Accreditation Programs, LLC

AIHA Laboratory Accreditation Programs, LLCacknowledges that

EMSL Analytical, Inc.200 Route 130 North, Cinnaminson, NJ 08077

Laboratory ID: 100194along with all premises from which key activities are performed, as listed above, has fulfilled the requirements of the AIHA Laboratory Accreditation Programs (AIHA-LAP), LLC accreditation to the ISO/IEC 17025:2005 international standard, General Requirements for the Competence of Testing and Calibration Laboratories in the following:

LABORATORY ACCREDITATION PROGRAMSINDUSTRIAL HYGIENE Accreditation Expires: September 01, 2018ENVIRONMENTAL LEAD Accreditation Expires: September 01, 2018ENVIRONMENTAL MICROBIOLOGY Accreditation Expires: September 01, 2018FOOD Accreditation Expires: UNIQUE SCOPES Accreditation Expires:

Specific Field(s) of Testing (FoT)/Method(s) within each Accreditation Program for which the above named laboratory maintains accreditation is outlined on the attached Scope of Accreditation. Continued accreditation is contingent upon successful on-going compliance with ISO/IEC 17025:2005 and AIHA-LAP, LLC requirements. This certificate is not valid without the attached Scope of Accreditation. Please review the AIHA-LAP, LLC website (www.aihaaccreditedlabs.org) for the most current Scope.

William Walsh, CIHChairperson, Analytical Accreditation Board

Cheryl O. MortonManaging Director, AIHA Laboratory Accreditation Programs, LLC

Revision 15: 03/30/2016 Date Issued: 08/31/2016

Effective: 04/10/2015100194_Scope_IHLAP (Method Addition)_2016_10_20Page 1 of 2

AIHA Laboratory Accreditation Programs, LLC

SCOPE OF ACCREDITATION

EMSL Analytical, Inc. Laboratory ID: 100194200 Route 130 North, Cinnaminson, NJ 08077 Issue Date: 10/20/2016

The laboratory is approved for those specific field(s) of testing/methods listed in the table below. Clients are urged to verify the laboratory’s current accreditation status for the particular field(s) of testing/Methods, since these can change due to proficiency status, suspension and/or withdrawal of accreditation.

Industrial Hygiene Laboratory Accreditation Program (IHLAP)

Initial Accreditation Date: 02/01/1989

IHLAP Scope Category

Field of Testing (FoT)(FoTs cover all relevant

IH matrices)

Technology sub-type/ Detector

Published Reference Method/Title of In-

house Method

Method Description or Analyte

(for internal methods only)

Chromatography Core

Gas Chromatography

GC/FID

NIOSH 1003 ModifiedNIOSH 1005

NIOSH 1400 ModifiedNIOSH 1500 ModifiedNIOSH 1501 ModifiedNIOSH 1550 ModifiedNIOSH 1603 ModifiedNIOSH 2000 Modified

GC/ECD

NIOSH 5502 ModifiedNIOSH 5503 ModifiedNIOSH 5510 ModifiedOSHA 1010 Modified

GC/MS GC/MS EPA TO-15Gas Chromatography (Diffusive Samplers) NIOSH 1501 Modified

Ion Chromatography (IC)

NIOSH 6004 ModifiedNIOSH 6011NIOSH 7903

OSHA ID-165SGOSHA ID-214

OSHA ID-215 Modified

Liquid ChromatographyHPLC/FL NIOSH 2016 ModifiedHPLC/UV NIOSH 5506 Modified

Spectrometry Core Atomic Absorption CVAANIOSH 6009 Modified

OSHA ID-140 ModifiedOSHA ID-145

Effective: 04/10/2015100194_Scope_IHLAP (Method Addition)_2016_10_20Page 2 of 2

IHLAP Scope Category

Field of Testing (FoT)(FoTs cover all relevant

IH matrices)

Technology sub-type/ Detector

Published Reference Method/Title of In-

house Method

Method Description or Analyte


Spectrometry Core

Atomic AbsorptionFAA NIOSH 7082

GFAA NIOSH 7105Inductively-Coupled

PlasmaICP/MS NIOSH 7300 ModifiedICP/AES NIOSH 7300 Modified

X-ray Diffraction (XRD)NIOSH 7500 Modified

OSHA ID-142 ModifiedUV/VIS (Colorimetric) NIOSH 6010 Modified

Asbestos/Fiber Microscopy Core

Polarized Light Microscopy (PLM) EPA 600/R-93/116

Phase Contrast Microscopy (PCM) NIOSH 7400

Transmission Electron Microscopy (TEM)

EPA AHERA - 40 CFR Part 763

EPA AHERA Method (40 CFR 763, Subpart E,

Appendix A, Mandatory Method

NIOSH 7402

Miscellaneous CoreGravimetric

NIOSH 0500NIOSH 0600NIOSH 5524

Thermo-optical Analysis (TOA) NIOSH 5040

Beryllium Testing Inductively-Coupled Plasma ICP/MS

NIOSH 7300NIOSH 7303

A complete listing of currently accredited Industrial Hygiene laboratories is available on the AIHA-LAP, LLC website at: http://www.aihaaccreditedlabs.org

Effective: 05/04/2015100194_Scope_ELLAP_2016_08_31Page 1 of 1





The EPA recognizes the AIHA-LAP, LLC ELLAP program as meeting the requirements of the National Lead Laboratory Accreditation Program (NLLAP) established under Title X of the Residential Lead-Based Paint Hazard Reduction Act of 1992 and includes paint, soil and dust wipe analysis. Air analysis is not included as part of the NLLAP.

Environmental Lead Laboratory Accreditation Program (ELLAP)


A complete listing of currently accredited Environmental Lead laboratories is available on the AIHA-LAP, LLC website at: http://www.aihaaccreditedlabs.org

Field of Testing (FoT) Technology sub-type/ Detector Method Method Description


Paint EPA SW-846 3050BEPA SW-846 7000B

Soil EPA SW-846 3050BEPA SW-846 7000B

Settled Dust by Wipe EPA SW-846 3050BEPA SW-846 7000B

Airborne Dust NIOSH 7082

Composited Wipes EPA SW-846 3050BEPA SW-846 7000B

Effective: 03/12/2013100194_Scope_EMLAP_2016_08_31Page 1 of 2





Environmental Microbiology Laboratory Accreditation Program (EMLAP)


EMLAP Category Field of Testing (FoT) Method Method Description


Fungal

Air - Culturable M005 Detection and Enumeration of Culturable Fungi from Environmental Samples

Bulk - Culturable M005 Detection and Enumeration of Culturable Fungi from Environmental Samples

Surface - Culturable M005 Detection and Enumeration of Culturable Fungi from Environmental Samples

Air - Direct Examination 05-TP-003.7

Standard Operating Procedure for the Analysis of Airborne Fungal Spores,

Hyphal Fragments, Pollen, Insect Fragments, Skin Fragments and Fibrous

Particulate by Optical Microscopy of Spore Trap Samples

Bulk - Direct Examination M041

Standard Operating Procedure for the Microscopic Examination of Fungal

Spores, Fungal Structures, Hyphae, Pollen, Insect Fragments, and Fibrous Material

from Surface Samples

Surface - Direct Examination M041

Standard Operating Procedure for the Microscopic Examination of Fungal

Spores, Fungal Structures, Hyphae, Pollen, Insect Fragments, and Fibrous Material

from Surface Samples

Bacterial

Air - Culturable M009 Detection and Enumeration of Culturable Bacteria from Environmental Samples

Bulk - Culturable M009 Detection and Enumeration of CulturableBacteria from Environmental Samples

Surface - Culturable M009Detection and Enumeration of Culturable

Bacteria from Environmental Samples

Effective: 03/12/2013100194_Scope_EMLAP_2016_08_31Page 2 of 2

EMLAP Category Field of Testing (FoT) Method Method Description


Bacterial Legionella 05-TP-002Recovery of Legionella from the

Environment Using the Center for Disease Control and Prevention’s Culture Method

A complete listing of currently accredited Environmental Microbiology laboratories is available on the AIHA-LAP, LLCwebsite at: http://www.aihaaccreditedlabs.org


End of Report

february 1, 2019 - city of anderson sc · 2019-02-14 · february 1, 2019 erica m. craft city of...

Documents