fbh1109 hood hinge installation instructions
TRANSCRIPT
-
8/7/2019 FBH1109 Hood Hinge Installation Instructions
1/2
1. Although our hinges are marketed as an easy install, Fesler Billet strongly
recommends that you have these hood hinges installed by a professional to
avoid the possibility of damaging your vehicle.
2. Fesler Billet is not responsible for customer applications that are outside the
normal and intended use of our products, including specific model and year
applications.
3. Fesler Billet designs hood hinges off original OEM applications. Due to the vast
array of manufacturers for aftermarket parts, it is possible that you may have to
open up your bolt holes in the sheet metal to accommodate the new hinge
application.
4. Due to the vast array of manufacturers for aftermarket parts, and the fact that
you are dealing with a vehicle that is well over 40 years old and has more than
likely seen several owners, you must assume that your original hood is no
longer original. Things like braces, paint and bondo significantly add to the
weight of any hood, therefore drastically affecting the strength of our hood
supports.
5. A common problem occurs with hinge installation when the mounting surface on
the inner fender is bent or out of alignment (pulled out or pushed in at one or
both mounting holes). If this is the case, the mounting holes will not line up
correctly with the hinge. To correct this, double check your inner fender mounting
positions by holding a straight edge against the two mounting holes on the inner
fender. If there is a gap between the straight edge and the sheet metal, the
mounting surface is bent or out of alignment.
6. *Some applications are not designed to work with your factory inner fenders.
Please check to see if your vehicle falls under this category before installing
hinges. Fesler Built is not responsible for damage to inner fenders on these
applications.
7. Depending on your hood manufacturer, you may need a shorter bolt when
attaching the hinge to the hood. Check length before tightening making sure to
look for dimpling.
8. DO NOT UNDER ANY CIRCUMSTANCES DISASSEMBLE THESE HINGES.
Doing so will void your warranty. You may not return hinges that have been
disassembled for any reason. We will be able to tell if you have disassembled
hinges upon their return and you will not be granted a refund if this is so.
QUESTIONS OR COMMENTS?
Call us at 1-866-583-9787
INSTALLATIONINSTRUCTIONS
FBH-1109
1967 1970 Ford Mustang
-
8/7/2019 FBH1109 Hood Hinge Installation Instructions
2/2
INSTALLATION INSTRUCTIONS
1967 1970 Ford MustangCopyright 2011 by Fesler Productions, LLC. All rights reserved.
1. Remove Hood
2. Remove the factory hinge from the fender
3. Inspect factory bolt holes in fender and test thread with new bolts.
a. Note: If existing bolt holes have damaged threads or rust,
you may have to re-tap them.
4. BEFORE installing your hinges on your vehicle, first install the
stainless steel gas spring to each hinge. IT IS IMPORTANT THATYOU INSTALL THE STRUT WITH THE SHAFT FACING THE REAR
OF THE CAR IN ORDER TO ENSURE PROPER OPERATION AND
PREVENT FAILURE.
5. Position each hinge on the corresponding fender and attach
using the supplied 5/16x1 socket head bolts, each with one
washer. Tighten bolts snug so they are securely attached to
fender. Note: 1 bolt will go in lower rear mounting hole.
6. Attach the hood to the hinges using the supplied 5/16 x 3/4
button head bolts, each with one washer.
a. Note: Be sure to use anti-seize on all bolts before
installing
7. To avoid hitting your cowl when closing the hood for the first time,
slide the hood as far forward as possible before closing. Close
hood carefully making sure it does not hit the fenders or cowl.
8. Check the height and position and make any adjustments by
repositioning the hinge slightly at the hood or fender locations.
PLEASE NOTE: IT IS NOT NECESSARY TO DRILL OUT
MOUNTING HOLES TO ACHIEVE MORE ADJUSTMENT.
DOING THIS WILL VOID ALL WARRANTIES NOT TO
MENTION BEING DANGEROUS.
9. Once hood position has been set, tighten all bolts, remove tape
and go.
10. Be sure to check and tighten ALL BOLTS (including assembly
bolts if necessary) every few months to avoid loosening, which is
often caused by normal use.
____________________________________________________________________
Important Technical Information:
Fesler Billet makes every effort to ensure that you are provided with the most accurate
and up-to-date technical information. However, all technical information is approximate
and may vary upon application. Fesler Billet is not responsible for any consequences
resulting from manufactures technical mid-year changes. Fesler Billet products should
only be installed by a qualified, licensed auto mechanic experienced in the installation of
such products.
Important Anodizing Information:
Anodizing does not produce "flawless" color or finish on any Fesler part ordered thatway. In fact, you should expect to encounter minor variations (or what some call
"blemishes") in the color and finish in individual pieces. Every Fesler finish is unique in
this regard. Remember, these variations are normal, and do not affect the performance
of the part in any way.
Other Important Stuff You Should Probably Read:
Fesler Billet is not responsible for customer applications that are outside the normal
and intended use of our products, including specific model and year applications.
Fesler Billet designs all parts off original OEM applications. Due to the vast array of
manufacturers for aftermarket parts, it is possible that you may have to make some
minor adjustments to either our part or your sheet metal in order for the part to fit
properly
ADJUSTMENTS
Height = Fender Adjustment
Front to Back = Hood Adjustment
Left to Right = Hood Adjustment
If your hood pops up at the cowl, you need to RAISE
the front of the hinge, NOT lower the entire hinge!