fatty ultra dl 70 fatty ultra dl 70 - jump...
TRANSCRIPT
© 2009 Cannondale Europe • www.cannondale.com
FATTY ULTRA DL 70
FATTY ULTRA DL 70
SpecificationsID: Tapered alloy inner steerer at crown junction, black top cap, silver hex nut, can have canti mount - disc mount or both,
Year 2000-2003
Travel (mm) 70
Damper Oil damped, cartridge
Spring element Air sprung, coil negative spring
Lockout Button On/Off
KITS
ITEM NUMBER DESCRIPTION
HDUPDD60/ Cartridge Kit, DD60 upgrade
HD110/BLU Spring Kit,DD60/MC60, medium
HD110/GRE Spring Kit,DD60/MC60, soft
HD110/RED Spring Kit,DD60/MC60, stiff
RECOMMENDED SAG
SAG
AB
B - A = SAG (mm)
Measure the length of the fork as shown below – remember this as measurement A.
With the help of a second person, seat the rider on the saddle with feet on pedals and hands on the handlebar. Again measure the length of the fork - remember this as measurement B.
To calculate sag subtract B from A .
The recommended sag measurement (in millimeters) as a percentage of your forks total travel, should fall within the guidelines listed in the attached chart.
To increase sag, release air. To decrease sag, add air.
PRESSURE LIMITS MINIMUM - 45 psi (3.1 bar) MAXIMUM - 120 psi (8.3 bar)
RECOMMENDED SAG 10-20% = 8mm
DIAL
© 2009 Cannondale Europe • www.cannondale.com
FATTY ULTRA DL 70
KITS
ITEM NUMBER DESCRIPTION
HD181/ DL 70 oil cartridge unit
HD183/ FT70/DL70 air cartridge
HDUPDL/70 Cartridge kit, DL70 upgrade
HD312/ Kit, Piston, DD60 w/ Seals & Shims
HD313/ Kit, lockout shims/seals DL Cartridge
HD314/ Kit, 5 X negative spring Green DL70
QHDST/EBO Headset Cannondale/Coda HeadShok Black
HD169/ Kit, Bearings, Headset - 2 / HeadShok
HD191/BLK Slim Boot, 5-rib, Black
HD191/YEL Slim Boot, 5-rib, Yellow
HD213/ Lock-Out lever
TOOLS
ITEM NUMBER DESCRIPTION
HD136/ Tool, HeadShok outer cap pin
HDTL149/ Tool, HeadShok fork installation
HDTL168/ Tool, bullet, Lefty and Fatty 12.7 mm
KT016/ Tool, HEADSHOK Bearing Reset
KT020/ Kit, Lefty Steerer install (also for Fattys)
KH031/ Super Castle Tool
© 2009 Cannondale Europe • www.cannondale.com
SUPER FATTY M 80
SUPER FATTY M 80
SpecificationsID: Tapered alloy inner steerer at crown junction, black top cap, can have canti mount - disc mount or both,
Year 1999-2005
Travel (mm) 80
Damper Mechanical damper/Friction
Spring element Coil sprung
Lockout No
Rebound No
KITS
ITEM NUMBER DESCRIPTION
HDUPDL/80 Cartridge Kit, DL80 upgrade
HD182/ DL80 Oil cartridge unit – Formerly DD80 Oil Cartridge
HD184/ FT80/DL80 Air cartridge
RECOMMENDED SAG
SAG
AB
B - A = SAG (mm)
Measure the length of the fork as shown below – remember this as measurement A.
With the help of a second person, seat the rider on the saddle with feet on pedals and hands on the handlebar. Again measure the length of the fork - remember this as measurement B.
To calculate sag subtract B from A .
The recommended sag measurement (in millimeters) as a percentage of your forks total travel, should fall within the guidelines listed in the attached chart.
To increase sag, release air. To decrease sag, add air.
PRESSURE SET UP
Spring preload
DIAL/TOP CAP
© 2009 Cannondale Europe • www.cannondale.com
SUPER FATTY M 80
KITS
ITEM NUMBER DESCRIPTION
QHDST/EBO Headset Cannondale/Coda HeadShok Black
HD169/ Kit, Bearings, Headset - 2/ HeadShok
HD191/BLK Slim Boot, 5-rib, Black
HD191/YEL Slim Boot, 5-rib, Yellow
HD213/ Lockout lever
HD155/BLU Spring Kit, MC80, Medium
HD155/GRE Spring Kit, MC80, Light
HD155/RED Spring Kit, MC80, Stiff
TOOLS
ITEM NUMBER DESCRIPTION
HD136/ Tool, HeadShok outer cap pin
HDTL149/ Tool, HeadShok fork installation
KT016/ Tool, HeadShok bearing reset
KT020/ Kit, Lefty Steerer install (also for Fattys)
KH031/ Super castle tool
© 2009 Cannondale Europe • www.cannondale.com
SUPER FATTY D & DL
SUPER FATTY D & DL
SpecificationsID: Shorter air valve end (ca. 8,5mm), 4 pin spanner holes under lockout dial, tapered inner tube down to crown.
Year 2001-2003
Travel (mm) 80
Damper Oil damped
Spring element Air sprung, coil negative spring
Lockout On the fly
Rebound No
KITS
ITEM NUMBER DESCRIPTION
HDUPDL/80 Cartridge Kit, DL80 upgrade
HD182/ DL80 Oil cartridge unit – Formerly DD80 Oil Cartridge
HD184/ FT80/DL80 Air cartridge
RECOMMENDED SAG
SAG
AB
B - A = SAG (mm)
Measure the length of the fork as shown below – remember this as measurement A.
With the help of a second person, seat the rider on the saddle with feet on pedals and hands on the handlebar. Again measure the length of the fork - remember this as measurement B.
To calculate sag subtract B from A .
The recommended sag measurement (in millimeters) as a percentage of your forks total travel, should fall within the guidelines listed in the attached chart.
To increase sag, release air. To decrease sag, add air.
DIAL
© 2009 Cannondale Europe • www.cannondale.com
SUPER FATTY D & DL
KITS
ITEM NUMBER DESCRIPTION
QHDST/EBO Headset Cannondale/Coda HeadShok Black
HD169/ Kit, Bearings, Headset - 2; HeadShok
HD191/BLK Slim Boot, 5-rib, Black
HD191/YEL Slim Boot, 5-rib, Yellow
HD213/ lockout lever
HDUPDL/80 CARTRIDGE KIT, DL80 UPGRADE
HD182/ DL80 Oil Cartridge Unit – Formerly DD80 Oil Cartridge
HD184/ FT80/DL80 Air Cartridge
HD166/ Seal Kit
HD212 Negative Spring
TOOLS
ITEM NUMBER DESCRIPTION
HD136/ Tool, HeadShok outer cap pin
HDTL149/ Tool, HeadShok fork installation
KT016/ Tool, HeadShok bearing reset
KT020/ Kit, Lefty Steerer install (also for Fattys)
KH031/ Super castle tool
HDTL168/ Bullet tool
© 2009 Cannondale Europe • www.cannondale.com
SUPER FATTY ULTRA DL (Inch thread)
SUPER FATTY ULTRA DL (INCH THREAD)
SpecificationsID: Shorter air valve end (ca. 8,5mm), 4 pin spanner holes under lockout dial, square inner tube down to crown.
Year 2001-2003
Travel (mm) 80
Damper Oil damped
Spring element Air sprung, coil negative spring
Lockout On the fly
Rebound No
KITS
ITEM NUMBER DESCRIPTION
HD155/BLU Spring Kit, MC80, Medium
HD155/GRE Spring Kit, MC80, Light
HD155/RED Spring Kit, MC80, Stiff
RECOMMENDED STARTING AIR PRESSURE
Lbs Kg Psi Bar
120 - 150 68 95 6.6
160 73 110 7.6
170 77 120 8.3
180 82 130 9.0
190 86 135 9.3
200 91 140 9.7
210 95 145 10.0
220 100 150 10.3
PRESSURE LIMITS MINIMUM - 70 psi (4.8 bar) MAXIMUM - 200 psi (13.8 bar)
RECOMMENDED SAG 10-20% = 8 mm
DIAL VALVE
© 2009 Cannondale Europe • www.cannondale.com
SUPER FATTY ULTRA DL (INCH THREAD)
HD169/
HD171/
27.0 Nm, 240 InLbsLoctite™ 242
20.0 Nm, 177 InLbs
HD182/
KF212/
HD191/BLKHD191/YEL
HD213/BLK
KITS
ITEM NUMBER DESCRIPTION
QHDST/EBO Headset Cannondale/Coda HeadShok Black
HD169/ Kit, Bearings, Headset - 2; HeadShok
HD191/BLK Slim Boot, 5-rib, Black
HD191/YEL Slim Boot, 5-rib, Yellow
HD213/ lockout lever
HDUPDL/80 CARTRIDGE KIT, DL80 UPGRADE
HD182/ DL80 Oil Cartridge Unit – Formerly DD80 Oil Cartridge
HD184/ FT80/DL80 Air Cartridge
TOOLS
ITEM NUMBER DESCRIPTION
HD136/ Tool, HeadShok outer cap pin
HDTL149/ Tool, HeadShok fork installation
KT016/ Tool, HeadShok bearing reset
KT020/ Kit, Lefty Steerer install (also for Fattys)
KH031/ Super castle tool
HDTL168/ Bullet tool
© 2009 Cannondale Europe • www.cannondale.com
SUPER FATTY ULTRA DLR Magura
SUPER FATTY ULTRA DLR MAgURA (INCH THREAD)
SpecificationsID: 13 mm higher outer tube (visual extension), hex nut for lock-out dial 15mm, red rebound dial with allen bolt in center, yellow/green cartridge body
Year 2005 (2006 with metric thread)
Travel (mm) 80
Damper Oil damped
Spring element Air sprung, coil negative spring
Lockout On the fly
Rebound External adjustment
RECOMMENDED STARTING AIR PRESSURE
Lbs Kg Psi Bar
120 54 50 3.4
130 59 55 3.8
140 64 60 4.1
150 68 65 4.5
160 73 70 4.8
170 77 75 5.2
180 82 80 5.5
190 86 90 6.2
200 91 100 7.2
PRESSURE LIMITS MINIMUM - 45 psi (3.1 bar) MAXIMUM - 120 psi (8.3 bar)
RECOMMENDED SAG 10-20% = 8 mm
DIAL INCH THREAD CARTRIDGE
© 2009 Cannondale Europe • www.cannondale.com
SUPER FATTY ULTRA DLR MAgURA (INCH THREAD)
HD170/
HD191/BLK
HD169/
HD171/
KF247/
KF226/
13mm Extension
KF232/
KF230/KF231/KF245/KF246/
KF229/
KF228/
TOOLS
ITEM NUMBER DESCRIPTION
HDTL149/ Tool, HeadShok Fork Installation
KT016/ Tool, HeadShok Bearing Reset
HDTL187/ Shaft Clamp Tool for Lefty and DL70
KT020/ Kit, Lefty Steerer install (also for Fattys)
KH031/ Super castle tool
KITS
ITEM NUMBER DESCRIPTION
KF235/ Upgrade kit, Damper, BLUE DL80
KF263/ Upgrade kit, Damper, RED DLR80, SOFT
KF264/ Upgrade kit, Damper, RED DLR80, STD
KF265/ Upgrade kit, Damper, RED DLR80, FIRM
KH005/ Kit, Air cylinder including Negative springs
HDUPDL/80 Cartridge kit, DL80 upgrade
© 2009 Cannondale Europe • www.cannondale.com
SUPER FATTY ULTRA DLR Magura
SUPER FATTY ULTRA DLR MAgURA (METRIC THREAD)
SpecificationsID: Metric thread, 13 mm higher outer tube (visual extension), hex nut for lockout dial 15mm, red rebound dial with allen bolt in center, yellow/green cartridge body (cartridge Body has small groove above thread)
Year 2006 with metric thread
Travel (mm) 80
Damper Oil damped
Spring element Air sprung, coil negative spring
Lockout On the fly
Rebound External adjustment
RECOMMENDED STARTING AIR PRESSURE
Lbs Kg Psi Bar
120 54 50 3.4
130 59 55 3.8
140 64 60 4.1
150 68 65 4.5
160 73 70 4.8
170 77 75 5.2
180 82 80 5.5
190 86 90 6.2
200 91 100 7.2
PRESSURE LIMITS MINIMUM - 45 psi (3.1 bar) MAXIMUM - 120 psi (8.3 bar)
RECOMMENDED SAG 10-20% = 8 mm
DIAL METRIC THREAD CARTRIDGE
© 2009 Cannondale Europe • www.cannondale.com
SUPER FATTY ULTRA DLR MAgURA (METRIC THREAD)
HD170/
HD191/BLK
HD169/
HD171/
KF247/
KF232/
KF230/KF231/KF245/KF246/
KF229/
KF228/
13mm Extension
TOOLS
ITEM NUMBER DESCRIPTION
HDTL149/ Tool, HeadShok Fork Installation
KT016/ Tool, HeadShok Bearing Reset
HDTL187/ Shaft Clamp Tool for Lefty and DL70
KT020/ Kit, Lefty Steerer install (also for Fattys)
KH031/ Super castle tool
KITS
ITEM NUMBER DESCRIPTION
KF235/ Upgrade kit, Damper, BLUE DL80
KF263/ Upgrade kit, Damper, RED DLR80, SOFT
KF264/ Upgrade kit, Damper, RED DLR80, STD
KF265/ Upgrade kit, Damper, RED DLR80, FIRM
KH005/ Kit, Air cylinder including Negative springs
© 2009 Cannondale Europe • www.cannondale.com
SUPER FATTY ULTRA DL (Metric thread)
SUPER FATTY ULTRA DL (METRIC THREAD)
SpecificationsID: Metric thread, silver top cap under lockout dial, 2-pin spanner holes, longer valve end (10,6mm)
Year 2005-2009
Travel (mm) 80
Damper Oil damped
Spring element Air sprung, coil negative spring
Lockout On the fly
Rebound No
KITS
ITEM NUMBER DESCRIPTION
KF263/ Kit, Damper, RED DLR80, SOFT - Upgrade possible
KF264/ Kit, Damper, RED DLR80, STD - Upgrade possible
KF265/ Kit, Damper, RED DLR80, FIRM - Upgrade possible
KH005/ Kit, Air cylinder including Negative springs
RECOMMENDED STARTING AIR PRESSURE
Lbs Kg Psi Bar
120 - 150 68 50 3.4
160 73 60 4.1
170 77 70 4.8
180 82 80 5.5
190 86 90 6.2
200 91 100 6.9
210 95 105 7.2
220 100 110 7.6
PRESSURE LIMITS MINIMUM - 40 psi (2.8 bar) MAXIMUM - 120 psi (8.3 bar)
RECOMMENDED SAG 10-20% = 8 mm
DIAL VALVE
© 2009 Cannondale Europe • www.cannondale.com
KF237/
HD170/
27.0 Nm, 240 InLbsLoctite™ 242
20.0 Nm, 177 InLbs
KF235/KF236/
KH005/
KP067/
KF238/
HD191/BLK
HD213/BLKHD169/
HD171/
SUPER FATTY ULTRA DL (METRIC THREAD)
KITS
ITEM NUMBER DESCRIPTION
KF235/ Kit, Damper, BLUE DL80
KF236/ Kit, Seal, BLUE DL80+05 DL50
KF237/ Kit, Schrader Plug, BLUE DL80, including Valve & Cap
KF238/ Kit, Air Piston, BLUE DL80, including Spring and holder
HD169/ Kit, Bearings, Headset - 2/ HeadShok
QHDST/EBO Headset Cannondale/Coda HeadShok Black
HD191/BLK Slim Boot, 5-rib, Black
HD191/YEL Slim Boot, 5-rib, Yellow
KP067/ Air piston quad seal, bag of 10
HD213/BLK Lockout lever
TOOLS
ITEM NUMBER DESCRIPTION
HD136/ Tool, HeadShok outer cap pin
HDTL149/ Tool, HeadShok fork installation
HDTL168/ TOOL, Bullet, Lefty and Fatty 12.7 mm
KT016/ Tool, HeadShok bearing reset
KH031 Super castle tool
KT020/ Kit, Lefty Steerer install (also for Fattys)
© 2009 Cannondale Europe • www.cannondale.com
SUPER FATTY ULTRA DLR
SUPER FATTY ULTRA DLR (METRIC THREAD)
SpecificationsID: Metric thread, long valve end, same lockout dial as Speed DLR, red rebound dial with set screw on side, conical top cap
Year 2006 +
Travel (mm) 80
Damper Oil damped/Cartridge
Spring element Air sprung, coil negative spring
Lockout On the fly
Rebound External adjustment
RECOMMENDED STARTING AIR PRESSURE
Lbs Kg Psi Bar
120 54 50 3.4
130 59 55 3.8
140 64 60 4.1
150 68 65 4.5
160 73 70 4.8
170 77 75 5.2
180 82 80 5.5
190 86 90 6.2
200 91 100 7.2
PRESSURE LIMITS MINIMUM - 45 psi (3.1 bar) MAXIMUM - 120 psi (8.3 bar)
RECOMMENDED SAG 10-20% = 8 mm
DLR DIAL
© 2009 Cannondale Europe • www.cannondale.com
SUPER FATTY ULTRA DLR (METRIC THREAD)
KF266/
KF210/
KF211/
KF237/
KF267/
HD170/
HD191/BLK
KP067/
HD169/
HD171/
KF263/KF264/KF265/KF236/
KH005/
KH022/
KITS
ITEM NUMBER DESCRIPTION
KF235/ Kit, Damper, BLUE DL80
KF236/ Kit, Seal, BLUE DL80+05 DL50
KF237/ Kit, Schrader Plug, BLUE DL80, including Valve & Cap
KF238/ Kit, Air Piston, BLUE DL80, including Spring and holder
HD169/ Kit, Bearings, Headset - 2/ HeadShok
QHDST/EBO Headset Cannondale/Coda HeadShok Black
HD191/BLK Slim Boot, 5-rib, Black
HD191/YEL Slim Boot, 5-rib, Yellow
KP067/ Air piston quad seal, bag of 10
HD213/BLK Lockout lever
© 2009 Cannondale Europe • www.cannondale.com
LEFTY DLR 100 Steel
LEFTY DLR 100 STEEL
SpecificationsID: Welded steel spindle, no threads under lockout dial, machined clamps, not bonded
Year 2000
Travel (mm) 100
Damper Oil damped
Spring element Air sprung, coil negative spring
Lockout On the fly
Rebound External adjustment
Compatilibities All HeadShok Stemscartridge and aircylinder not compatible with 2001+ parts
RECOMMENDED SAG
SAG
AB B - A = SAG (mm)
Measure the length of the fork as shown below – remember this as measurement A.
With the help of a second person, seat the rider on the saddle with feet on pedals and hands on the handlebar. Again measure the length of the fork - remember this as measurement B.
To calculate sag subtract B from A .
The recommended sag measurement (in millimeters) as a percentage of your forks total travel, should fall within the guidelines listed in the attached chart.
To increase sag, release air. To decrease sag, add air.
RECOMMENDED SAG
XC 20-30%
DIAL
© 2009 Cannondale Europe • www.cannondale.com
LEFTY DLR 100 STEEL
KITS
ITEM NUMBER DESCRIPTION
HD201/ Lefty DLR '00 Dial Holder Plug For Lockout/Damping ADJ
HD202/BLU Lefty DLR '00 Oil Damper Cartridge, MEDIUM
HD202/GRN Lefty DLR '00 Oil Damper Cartridge, SOFT
HD202/RED Lefty DLR '00 Oil Damper Cartridge, HARD
HD203/ Lefty DLR '00 Air Cylinder and Air Piston
HD211/ Lefty DLR '00 Air Cylinder Saddle
HD214/ Lefty DLR '00 Damping Adjuster Knob
HD212/ Negative Spring KIT for Lefty 100 Oil Cart
HD212/WHT Kit, Spring - Negative, Lefty, X-firm
HD011/ Kit, Band Clamp Cable Guide (2), Boot Lefty
HD205/ Lefty Upper clamp
HD206/ Lower crown/steerer, Lefty 100
TOOLS
ITEM NUMBER DESCRIPTION
HDTL200/ Tool, HeadShok Lefty cart castles '00 only
KT020/ Steerer instalation/removal
HDTL168/ 1/2 bullet tool
HD187/ 1/2 inch shaft clamps
QCTL108/ Tool, Lefty truing axle
KT016/ Tool, HeadShok Bearing Reset
© 2009 Cannondale Europe • www.cannondale.com
LEFTY DLR 100 Steel or Titanium
LEFTY DLR 100 (STEEL oR TITANIUM)
SpecificationsID: Titanium or steel spindel, threads and large lockring under lockout dial, forged clamps – not bonded
Year 2000-2004
Travel (mm) 100
Damper Oil damped
Spring element Air sprung, coil negative spring
Lockout On the fly
Rebound External adjustment
Compatilibities All HeadShok StemsCartridge and aircylinder Not compatible with 2000 parts
RECOMMENDED SAG
SAG
AB B - A = SAG (mm)
Measure the length of the fork as shown below – remember this as measurement A.
With the help of a second person, seat the rider on the saddle with feet on pedals and hands on the handlebar. Again measure the length of the fork - remember this as measurement B.
To calculate sag subtract B from A .
The recommended sag measurement (in millimeters) as a percentage of your forks total travel, should fall within the guidelines listed in the attached chart.
To increase sag, release air. To decrease sag, add air.
RECOMMENDED SAG
XC 20-30%
DIAL
© 2009 Cannondale Europe • www.cannondale.com
LEFTY DLR 100 (STEEL oR TITANIUM)
KITS
ITEM NUMBER DESCRIPTION
HD166/ KIT All Seals, FT, DL and Lefty 100 cartridges
HD001/ Kit, '01 DLR Dial holder/plug
HD002/ Kit, Air cylinder for '01 DLR
HD022/ Kit, Damp Adjust Knob-2nd. Lefty '01->
HD023/ Kit, 2001 DLR Damper - SM
HD026/ Kit, Perch-DL70/80, DLR 100
HD212/ Negative Spring Kit for Lefty 100 Oil Cart
HD212/WHT Kit, Spring - Negative, Lefty, X-firm
HD011/ Kit, Band Clamp Cable Guide (2), Boot Lefty
HD205/ Lefty Upper clamp
HD206/ lower crown/steerer, Lefty 100
KT040/ Kit, Steerer, X-Long Lefty
HD016/ Steerer, Lefty
TOOLS
ITEM NUMBER DESCRIPTION
KT006/ Tool , lower cartridge Cap remover
KT020/ Steerer installation/removal
HDTL168/ 1/2 bullet tool
HD187/ 1/2 inch shaft clamps
KT004/ Tool, Lefty DLR/ELO Kidney tool '01 and +
QCTL108/ Tool, Lefty Truing Axle
KT016/ Tool, HeadShok Bearing Reset
© 2009 Cannondale Europe • www.cannondale.com
LEFTY CARBON DLR 100 Forged Steel or Titanium ELO or DLR
LEFTY CARboN ELo oR DLR 100
SpecificationsID: Titanium or steel spindle, threads and large lockring under lock-out dial, forged bonded clamps, carbon outer tube, first gen. has carbon inner tube
Year 2001-2004
Travel (mm) 100
Damper Oil damped
Spring element Air sprung, coil negative spring
Lockout On the fly or ELO (electronic lockout)
Rebound External adjustment
Compatilibities Cartridge and aircylinder not compatible with 2000 parts, fits Stem/steerer, (carbon) SL steeringtube and extra long steeringtube.
RECOMMENDED SAG
SAG
AB B - A = SAG (mm)
Measure the length of the fork as shown below – remember this as measurement A.
With the help of a second person, seat the rider on the saddle with feet on pedals and hands on the handlebar. Again measure the length of the fork - remember this as measurement B.
To calculate sag subtract B from A .
The recommended sag measurement (in millimeters) as a percentage of your forks total travel, should fall within the guidelines listed in the attached chart.
To increase sag, release air. To decrease sag, add air.
RECOMMENDED SAG
XC 20-30%
ELO DIAL DLR DIAL
© 2009 Cannondale Europe • www.cannondale.com
LEFTY CARboN ELo oR DLR 100
KITS
ITEM NUMBER DESCRIPTION
HD166/ KIT All Seals, FT, DL and Lefty 100 cartridges
HD001/ Kit, '01 DLR Dial holder/plug
HD002/ Kit, Air cylinder for '01 DLR
HD022/ Kit, Damp Adjust Knob-2nd. Lefty '01->
HD023/ Kit, 2001 DLR Damper - SM
HD026/ Kit, Perch-DL70/80, DLR 100
HD212/ Negative Spring Kit for Lefty 100 Oil Cart
HD212/WHT Kit, Spring - Negative, Lefty, X-firm
HD011/ Kit, Band Clamp Cable Guide (2), Boot Lefty
HD205/ Lefty Upper clamp
HD206/ lower crown/steerer, Lefty 100
KT040/ Kit, Steerer, X-Long Lefty
HD016/ Steerer, Lefty
HD300/ Kit, Battery – ELO Li-Ion high power
HD301/ Kit, Elec. Cont. Unit - ELO
HD003/ Collar, Upper Carbon Lefty
HD004/ Collar, Lower, Lefty Carbon gold
HD005/ Kit, Air Cylinder Saddle-2002 Full Carbon Lefty
HD027/ Kit, Perch -Carbon ELO
HD010/ Kit, Spacers-Lefty Travel Reducers
TOOLS
ITEM NUMBER DESCRIPTION
KT006/ Tool , lower cartridge Cap remover
KT020/ Steerer installation/removal
HDTL168/ 1/2 bullet tool
HD187/ 1/2 inch shaft clamps
KT004/ Tool, Lefty DLR/ELO Kidney tool '01 and +
QCTL108/ Tool, Lefty Truing Axle
KT016/ Tool, HeadShok Bearing Reset
HD003/
HD002/
HD205/
HD301/
HD004/
© 2009 Cannondale Europe • www.cannondale.com
LEFTY MAX 140 FFD (Fluid Flow Damping)Only Alloy version
LEFTY MAx 140 FFD
SpecificationsID: Black spindle, alloy outer tube, polished clamps, red rebound dial - no screw, bottom (images)
Year 2006 + 2007
Travel (mm) 140
Damper Oil damped
Spring element Steel coil sprung, “Fluid Flow Damping”
Lockout No
Rebound External adjustment
Compatilibities All stems (not stem/steerer) TPC + SPV upgrade possible
KITS
ITEM NUMBER DESCRIPTION
KF216/ Kit, Damper, Compression, MAX140, TPC
KF220/ Kit, Bladder only SPV, MAX140
KF223/ Kit, Damper, Compression, MAX140, SPV
KF218/ Kit, Damper, Rebound, MAX140, SPV
PRESSURE SET UP
Spring preload
RECOMMENDED SAG
XC 20-30%
Trail 25-35%
DIAL
© 2009 Cannondale Europe • www.cannondale.com
LEFTY MAx 140 FFD
KITS
ITEM NUMBER DESCRIPTION
KF215/ Kit, Damper, Compression, MAX140, FFD
KF217/ Kit, Damper, Rebound, MAX140, FFD/TPC
KF221/ Kit, Knob, Compression, MAX140, TPC
KF222/ Kit, Boot, Lefty MAX 140
KF219/ Kit, Damper, Control ASSY, MAX140
KF224/ Kit, Damper, Piston Ring, MAX140-5
KF225/ Kit, Seal, Max140
KF233/ Kit, KNOB, REBOUND, MAX140
KF234/ Kit, PUSHROD, MAX140
KF354/ KIT, TACHO MOUNT LEFTY FORKS
HD011/ Kit, Band Clamp Cable Guide (2), Boot Lefty
HD210/ Lefty steerer tube plug
QSMSEAL/ Upper HeadShok bearing seal
HD209/BLK Air filter hood and filter unit for Lefty, Black
KF205/ Kit, Split Ring, 2
KF206/ Kit, Collar, Upper, Alloy, Speed110/MAX140
QC679/ Kit, Clamp, Upper, MAX
QC680/ Kit, Clamp, Lower, MAX
22mm10 Nm, 89 InLbs
2mm
HD210/
QL679/
KF233/
KF206/
KF205/
KF225/
KF217/
KF234/
KF215/
KF219/HD209/BLK
KF222/
KF354/
QL680/
TOOLS
ITEM NUMBER DESCRIPTION
QCTL108/ Tool, Lefty Truing Axle
SPRINGS
ITEM NUMBER DESCRIPTION
KF213/BLK Kit, Spring, MAX140 FE, XFIRM
KF213/BLU Kit, Spring, MAX140 FE, STD
KF213/BRN Kit, Spring, MAX140 FE, XXFIRM
KF213/GRN Kit, Spring, MAX140 FE, SOFT
KF213/RED Kit, Spring, MAX140 FE, FIRM
KF214/BLU Kit, Spring, MAX140 TI, STD
KF214/GRN Kit, Spring, MAX140 TI, SOFT
KF214/RED Kit, Spring, MAX140 TI, FIRM
© 2009 Cannondale Europe • www.cannondale.com
LEFTY MAX 140 TPC Only Alloy version
LEFTY MAx 140 TPC
SpecificationsID: black spindle, alloy outer tube, polished clamps, red rebound dial - no screw, blue dial with set screw at bottom (images)
Year 2006 + 2007
Travel (mm) 140
Damper Oil damped
Spring element Steel coil sprung, “Twin Piston Chamber”
Lockout No
Rebound External adjustment
Compatilibities All stems (not stem/steerer) SPV upgrade possibleKit for 120 travel available
KITS
ITEM NUMBER DESCRIPTION
KF220/ Kit, Bladder only SPV, MAX140
KF223/ Kit, Damper, Compression, MAX140, SPV
KF218/ Kit, Damper, Rebound, MAX140, SPV
PRESSURE SET UP
Spring preload
RECOMMENDED SAG
Trail 25-35%
TPC DIAL TPC KNOB (BOTTOM)
© 2009 Cannondale Europe • www.cannondale.com
LEFTY MAx 140 TPC
KITS
ITEM NUMBER DESCRIPTION
KF215/ Kit, Damper, Compression, MAX140, FFD
KF216/ Kit, Damper, Compression, MAX140, TPC
KF217/ Kit, Damper, Rebound, MAX140, FFD/TPC
KF221/ Kit, Knob, Compression, MAX140, TPC
KF222/ Kit, Boot, Lefty MAX 140
KF219/ Kit, Damper, Control ASSY, MAX140
KF224/ Kit, Damper, Piston Ring, MAX140-5
KF225/ Kit, Seal, MAX140
KF233/ Kit, KNOB, Rebound, MAX140
KF234/ Kit, Pushrod, MAX140
KF354/ KIT, Tacho Mount Lefty Forks
HD011/ Kit, Band Clamp Cable Guide (2), Boot Lefty
HD210/ Lefty steerer tube plug
QSMSEAL/ Upper HeadShok bearing seal
HD209/BLK Air filter hood and filter unit for Lefty, Black
KF205/ Kit, Split Ring, 2
KF206/ Kit, Collar, Upper, Alloy, Speed110/MAX140
QC679/ Kit, Clamp, Upper, MAX
QC680/ Kit, Clamp, Lower, MAX
22mm10 Nm, 89 InLbs
2mm
2mm
HD210/
QL679/KF233/
KF206/
KF205/
KF225/
KF217/
KF224/
KF216/
KF221/
KF234/
KF219/
HD209/BLK
KF222/
KF354/
QL680/
TOOLS
ITEM NUMBER DESCRIPTION
QCTL108/ Tool, Lefty Truing Axle
SPRINGS
ITEM NUMBER DESCRIPTION
KF213/BLK Kit, Spring, MAX140 FE, XFIRM
KF213/BLU Kit, Spring, MAX140 FE, STD
KF213/BRN Kit, Spring, MAX140 FE, XXFIRM
KF213/GRN Kit, Spring, MAX140 FE, SOFT
KF213/RED Kit, Spring, MAX140 FE, FIRM
KF214/BLU Kit, Spring, MAX140 TI, STD
KF214/GRN Kit, Spring, MAX140 TI, SOFT
KF214/RED Kit, Spring, MAX140 TI, FIRM
© 2009 Cannondale Europe • www.cannondale.com
LEFTY MAX 140 SPV evolveCarbon & Alloy version (IMAGE SHOWS ALLOY)
LEFTY MAx 140 SPV EVoLVE
SpecificationsID: Titanium or steel spindle, threads and large lockring under lock-out dial, forged bonded clamps, carbon outer tube (for carbon version), first gen. has carbon inner tube
Year 2006 + 2007
Travel (mm) 140
Damper Oil damped
Spring element Ti coil sprung, SPV
Lockout Adjustable rebound
Rebound External adjustment
Compatilibities Alloy: All stems (not stem/steerer)Carbon: All stems and stem/steerer TPC downgrade possibleKit for 120 travel available
KITS
ITEM NUMBER DESCRIPTION
KF215/ Kit, Damper, Compression, MAX140, FFD
KF216/ Kit, Damper, Compression, MAX140, TPC
KF217/ Kit, Damper, Rebound, MAX140, FFD/TPC
RECOMMENDED STARTING AIR PRESSURE
Lbs Kg Psi Bar SPRING
120 54 40 2.8 GREEN
130 59 50 3.4 GREEN
140 64 60 4.1 GREEN
150 68 50 3.4 BLUE
160 73 60 4.1 BLUE
170 77 60 4.1 RED
180 82 60 4.1 RED
190 86 60 4.1 BLACK
200 91 70 4.8 BLACK
210 95 70 4.1 BLACK
220 100 5.5 5.5 BLACK
PRESSURE LIMITS MINIMUM - 45 psi (3.1 bar) MAXIMUM - 120 psi (8.3 bar)
RECOMMENDED SAG 25-35%
© 2009 Cannondale Europe • www.cannondale.com
LEFTY MAx 140 SPV EVoLVE
KITS
ITEM NUMBER DESCRIPTION
KF214/RED Kit, Spring, MAX140 TI, FIRM
KF218/ Kit, Damper, Rebound, MAX140, SPV
KF219/ Kit, Damper, Control ASSY, MAX140
KF220/ Kit, Bladder only SPV, MAX140
KF221/ Kit, Knob, Compression, MAX140, TPC
KF222/ Kit, Boot, Lefty MAX 140
KF223/ Kit, Damper, Compression, MAX140, SPV
KF224/ Kit, Damper, Piston Ring, MAX140-5
KF225/ Kit, Seal, Max140
KF233/ Kit, Knob, Rebound, MAX140
KF234/ Kit, Pushrod, MAX140
KF354/ Kit, Tacho Mount Lefty Forks
HD011/ Kit, Band Clamp Cable Guide (2), Boot Lefty
HD210/ Lefty steerer tube plug
QSMSEAL/ Upper HeadShok bearing seal
HD209/BLK Air filter hood and filter unit for Lefty, Black
KF205/ Kit, Split Ring, 2
KF206/ Kit, Collar, Upper, Alloy, Speed110/MAX140
QC679/ Kit, Clamp, Upper, MAX
QC680/ Kit, Clamp, Lower, MAX
4
HD210/
QL679/
KF233/
KF206/
KF218
KF205/
KF225/
KF224/
KF219/
HD209/BLK
KF222/
KF354/
QL680/
TOOLS
ITEM NUMBER DESCRIPTION
QCTL108/ Tool, Lefty Truing Axle
SPRINGS
ITEM NUMBER DESCRIPTION
KF213/BLK Kit, Spring, MAX140 FE, XFIRM
KF213/BLU Kit, Spring, MAX140 FE, STD
KF213/BRN Kit, Spring, MAX140 FE, XXFIRM
KF213/GRN Kit, Spring, MAX140 FE, SOFT
KF213/RED Kit, Spring, MAX140 FE, FIRM
KF214/BLU Kit, Spring, MAX140 TI, STD
KF214/GRN Kit, Spring, MAX140 TI, SOFT
KF214/RED Kit, Spring, MAX140 TI, FIRM
© 2009 Cannondale Europe • www.cannondale.com
LEFTY SPEED DLR 110
LEFTY SPEED DLR 110
SpecificationsID: Color: black metal, clamps forged - not bonded to outer tube, outer tube alloy, black spindle, red rebound dial - set screw on side metal lockout dial, gold cartridge body
Year 2006 + 2007
Travel (mm) 110
Damper Oil damped
Spring element Air sprung, coil negative spring
Lockout On the fly
Rebound External adjustment
Compatilibities Cartridge NOT compatible with black SL110!
RECOMMENDED STARTING AIR PRESSURE
Lbs Kg Psi Bar
120 54 80 5.5
130 59 85 5.9
140 64 90 6.2
150 68 100 6.9
160 73 105 7.2
170 77 110 7.6
180 82 120 7.3
190 86 125 8.6
200 91 130 9.0
210 95 135 9.3
220 100 145 10.0
PRESSURE LIMITS MINIMUM - 50 psi (3.4 bar) MAXIMUM - 225 psi (15.5 bar)
RECOMMENDED SAG XC 20-30%
DLR DIAL
© 2009 Cannondale Europe • www.cannondale.com
LEFTY SPEED DLR 110
KITS
ITEM NUMBER DESCRIPTION
KF202/ Kit, Seal, Speed 110
KF204/ Kit, Shim, Revavling, Speed110/MAX140
KF205/ Kit, Split Ring,2
KF206/ Kit, Collar, Upper, Alloy, Speed110/MAX140 (old style)
KF207/ Kit, Collar, Upper, Carbon, Speed110/MAX140
KF210/ Kit, Lever, Lockout, Speed110 w/nut
KF211/ Kit, Knob, Rebound, Speed 110
KF212/ Kit, Cap, Air Valve, Speed 110
KF213/ Kit, Piston, Air, Speed 110
HD169/ Kit, Bearings, Headset - 2; HeadShok
QHDST/EBO Headset Cannondale/Coda HeadShok Black
QC678/ Kit, Boot, Lefty MAX /Jake, tailed
HD209/BLK Air filter hood and filter unit for Lefty, Black only
HD210/ Lefty steerer tube plug
KT040/ Kit, Steerer, X-Long Lefty
HD016/ Steerer, Lefty
QSMSEAL/ Upper HeadShok bearing seal
HD011/ Kit, Band Clamp Cable Guide (2), Boot Lefty
HD205/ Lefty Upper clamp
HD206/ lower crown/steerer, lefty
TOOLS
ITEM NUMBER DESCRIPTION
KT020/ Steerer installation/removal
HDTL168/ 1/2 bullet tool
QCTL108/ Tool, Lefty Truing Axle
KH031/ Super castle tool
Rider WT. (lbs) Rider WT. (kg) Fork size Bike Size Neg. Spring Kits
to 145 65 SOFT PT/SM GREEN KF200/GRN
145-175 65 - 79 STANDARD MD BLUE KF200/BLU
175-195 79 - 88 FIRM LG RED KF200/RED
195 + 88 + X-FIRM XL BLACK KF200/BLK
© 2009 Cannondale Europe • www.cannondale.com
LEFTY SPEED DLR2 110Carbon & Alloy version (IMAGE SHOWS ALLOY)
LEFTY SPEED DLR2 110 CARboN & ALLoY
SpecificationsID: Color: gun metal or carbon, clamps bonded, outer tube alloy or carbon, black spindle, red rebound dial, metal lockout dial, gold cartridge body.
Year Alloy 2006-2008Carbon 2006-2007
Travel (mm) 110
Damper Oil damped
Spring element Air sprung, coil negative spring
Lockout On the fly
Rebound External adjustment
Compatilibities Fits all HeadShok stems and stem/steeres,Cartridge NOT compatible with SL110!
KITS
ITEM NUMBER DESCRIPTION
KH055/ Kit, Convert, DLRSL&DLR2 - Solo Air
RECOMMENDED STARTING AIR PRESSURE
Lbs Kg Psi Bar
120 54 85 5.9
130 59 90 6.2
140 64 100 6.9
150 68 105 7.2
160 73 110 7.6
170 77 115 8.0
180 82 125 8.6
190 86 130 9.0
200 91 140 9.7
210 95 145 10.0
220 100 155 10.7
PRESSURE LIMITS MINIMUM - 50 psi (3.4 bar) MAXIMUM - 225 psi (15.5 bar)
RECOMMENDED SAG 20 - 30% (22.0 - 23.0 mm)
DLR2 DIAL
© 2009 Cannondale Europe • www.cannondale.com
LEFTY SPEED DLR2 110 CARboN & ALLoY
9.0 Nm, 80 InLbs
20.0 Nm, 177 InLbs
28.0 Nm, 248 InLbsLoctite™ 242
0.33 Nm, 3 InLbs
0.23 Nm, 2.0 InLbs
HD215/
HD209/BLK
QC678/
Carbon version KF207/Alloy version KF206/
KF212/
16mm
LEFTYBOLTS
HD011/
KF205/
HD175/BLKHD185/BLK
KF211/
9.0 Nm, 80 InLbs
KH057/
KF272/
KF210/
28.0 Nm, 248 InLbs
2.0 Nm, 18 InLbs
10 Nm, 89 InLbsLoctite™ 262
KF200/***
KF201/***KF202/KF204/
KF213/
Rider WT. (lbs) Rider WT. (kg) Fork size Bike Size Neg. Spring Kits
to 145 65 SOFT PT/SM GREEN KF200/GRN
145-175 65 - 79 STANDARD MD BLUE KF200/BLU
175-195 79 - 88 FIRM LG RED KF200/RED
195 + 88 + X-FIRM XL BLACK KF200/BLK
© 2009 Cannondale Europe • www.cannondale.com
LEFTY SPEED CARBON FOX Terra Logic
LEFTY SPEED CARboN Fox TERRA LogIC
SpecificationsID: Color: carbon w/polished clamps, clamps bonded, outer tube carbon, black spindle, large red rebound dial, small silver cap in center, blue threshold knob at bottom.
Year 2006
Travel (mm) 110
Damper Oil damped
Spring element Air sprung, float air negative spring
Lockout Inertia valve lockout
Rebound External adjustment
Compatilibities Fits all HeadShok stems and stem/steeres,Cartridge NOT compatible with SL110 or DLR110 RLC 110 upgrade possible
RECOMMENDED STARTING AIR PRESSURE
Lbs Kg Psi Bar
140 64 35 2.4
150 68 40 2.8
160 73 45 3.1
170 77 50 3.4
180 82 60 4.1
190 86 70 4.8
PRESSURE LIMITS MINIMUM - 20 psi (1.4 bar) MAXIMUM - 120 psi (8.3 bar)
RECOMMENDED SAG 20 - 30% (22.0 - 23.0 mm)
DIAL
© 2009 Cannondale Europe • www.cannondale.com
LEFTY SPEED CARboN Fox TERRA LogIC
KITS
ITEM NUMBER DESCRIPTION
KF250/ KIT, KNOB, REBOUND, Lefty-FOX Terra Logic IV
KF251/ KIT, SPRING, AIR ON TOP, Lefty-FOX Terra Logic IV
KF252/ Kit, D amper, Lefty-FOX Terra Logic IV
KF253/ Kit, Seal, Air on top, Lefty-FOX Terra Logic IV
HD169/ Kit, Bearings, Headset - 2; HeadShok
QHDST/EBO Headset Cannondale/Coda HeadShok Black
QC678/ Kit, Boot, Lefty MAX /Jake, tailed
HD209/BLK Air filter hood and filter unit for Lefty, Black only
HD210/ Lefty steerer tube plug
KT040/ KIT, STEERER, X-LONG LEFTY
HD016/ Steerer, Lefty
QSMSEAL/ Upper HeadShok bearing seal
HD011/ Kit, Band Clamp Cable Guide (2), Boot Lefty
TOOLS
ITEM NUMBER DESCRIPTION
KT020/ Steerer installation/removal
QCTL108/ Tool, Lefty Truing Axle
© 2009 Cannondale Europe • www.cannondale.com
LEFTY SPEED CARBON SL 110
LEFTY SPEED CARboN SL 110
SpecificationsID: Blue lockout dial, SL laser etched on black spindle polished clamps - machined flat, black cartidge body.
Year 2007-2009
Travel (mm) 110
Damper Oil damped
Spring element Air sprung, coil negative spring
Lockout On the fly
Rebound External adjustment
Compatilibities Stems, steering tubes, stem/steeres
KITS
ITEM NUMBER DESCRIPTION
KH055/ Kit, Convert, DLRSL&DLR2 – Solo Air
RECOMMENDED STARTING AIR PRESSURE
Lbs Kg Psi Bar
120 54 80 5.5
130 59 85 5.9
140 64 90 6.2
150 68 100 6.9
160 73 105 7.2
170 77 110 7.6
180 82 120 7.3
190 86 125 8.6
200 91 130 9.0
210 95 135 9.3
220 100 145 10.0
PRESSURE LIMITS MINIMUM - 50 psi (3.4 bar) MAXIMUM - 225 psi (15.5 bar)
RECOMMENDED SAG 20 - 30% = (22.0 - 23.0 mm)
DIAL
© 2009 Cannondale Europe • www.cannondale.com
KT028/20Nm, 177 InLbs
2 Nm, 18 InLbs
28 Nm248 InLbs
Apply NL GI-2 Synthetic grease to items marked
KF211/
KT031/
KT027/
KF205/
KH055/
KH026/
HD215/
HD011/
HD209/
QC678/
HO175/BLKHO185/BLK
29’er Travelreduction spacers3 x 10 mm
LEFTY SPEED CARboN SL 110
Rider WT. (lbs) Rider WT. (kg) Fork size Bike Size Neg. Spring Kits
to 145 65 SOFT PT/SM GREEN KT025/GRN
145-175 65 - 79 STANDARD MD BLUE KT025/BLU
175-195 79 - 88 FIRM LG RED KT025/RED
195 + 88 + X-FIRM XL BLACK KT025/BLK
KITS
ITEM NUMBER DESCRIPTION
KT026/GRN KIT, DAMPER LEFTY DLRSL (remove volume compensator)
KT026/BLU KIT, DAMPER LEFTY DLRSL (remove volume compensator)
KT026/RED KIT, DAMPER LEFTY DLRSL (remove volume compensator)
KT026/BLK KIT, DAMPER LEFTY DLRSL (remove volume compensator)
KT213 KIT, AIR PISTON
© 2009 Cannondale Europe • www.cannondale.com
LEFTY SPEED SL2 CARBON 110 (Solo Air)
LEFTY SPEED CARboN SL2 110 (SoLo AIR)
SpecificationsID: Blue lockout dial, red rebound dial with set screw on side, polished clamps - machined flat, OPI laser etched on black spindle.
Year 2009 +
Travel (mm) 110
Damper Oil damped
Spring element Air sprung, SOLO AIR self adjusting negative spring
Lockout On the fly
Rebound External adjustment
Compatilibities Stems, steering tubes, Stem/steerer
RECOMMENDED STARTING AIR PRESSURE
Lbs Kg Psi Bar
120 54 85 5.9
130 59 90 6.2
140 64 100 6.9
150 68 105 7.2
160 73 110 7.6
170 77 115 8.0
180 82 125 8.6
190 86 130 9.0
200 91 140 9.7
210 95 145 10.0
220 100 155 10.7
PRESSURE LIMITS MINIMUM - 50 psi (3.4 bar) MAXIMUM - 225 psi (15.5 bar)
RECOMMENDED SAG 20 - 30% = (22.0 - 23.0 mm)
DIAL OPI SPINDLE
© 2009 Cannondale Europe • www.cannondale.com
LEFTY SPEED CARboN SL2 110 (SoLo AIR)
KT028/20Nm, 177 InLbs
2 Nm, 18 InLbs
28 Nm248 InLbs
Apply NL GI-2 Synthetic grease to items marked
KF211/
KT031/
KT027/
KF205/
KH055/
KH026/
HD215/
HD011/
HD209/
QC678/
* DRAWING DOES NOT SHOW OPI SPINDLE
HO175/BLKHO185/BLK
29’er Travelreduction spacers3 x 10 mm
KITS
ITEM NUMBER DESCRIPTION
KH052/ Kit, Air Piston, DLR SL, Solo Air
KT024/ Kit, Seals, DLR SL
KT051 Kit, Damper, Lefty DLR SL, Solo
© 2009 Cannondale Europe • www.cannondale.com
LEFTY MAX CARBON FOX RLC 130
LEFTY MAx CARboN Fox RLC 130
SpecificationsID: Red rebound dial with allen screw in center, 2nd blue adjust wheel under lockout dial.
Year 2008-2009 +
Travel (mm) 130
Damper Oil damped
Spring element Ti coil spring, Adjustable low-speed comp
Lockout Yes, Adjustable lock-out threshold
Rebound External Adjustment
Compatilibities Stems, steering tubes, Stem/steerer
KITS
ITEM NUMBER DESCRIPTION
KH041/ Lefty PBR Damper
RECOMMENDED SAG
SAG
AB B - A = SAG (mm)
Measure the length of the fork as shown below – remember this as measurement A.
With the help of a second person, seat the rider on the saddle with feet on pedals and hands on the handlebar. Again measure the length of the fork - remember this as measurement B.
To calculate sag subtract B from A .
The recommended sag measurement (in millimeters) as a percentage of your forks total travel, should fall within the guidelines listed in the attached chart.
To increase sag, release air. To decrease sag, add air.
RECOMMENDED SAG
Trail 25-35%
DIAL
© 2009 Cannondale Europe • www.cannondale.com
LEFTY MAx CARboN Fox RLC 130
KF222/
HD209/BLK
KH014/
KH025/
SUPPLIEDBYFOX
KH015/
KH032/033/034/035/
KITS
ITEM NUMBER DESCRIPTION
KH032/ Spring, soft, ti
KH033/ Spring, standard, ti
KH034/ Spring, firm, ti
KH035/ Spring, x-firm, ti
KH025/ FOX RLC preload tube
KH011/ FOX RLC upgrade kit
KH012/ FOX RLC seal kit
KH028/ FOX RLC rebound shaft
KH015/ FOX RLC compression damper
KH029/ FOX RLC seal head
KH026/ FOX RLC compression clamp
KH027/ FOX RLC retaining ring
KF205/ Split rings 2
KH016/ FOX RLC outer collar
HD169/ Kit, Bearings, Headset - 2; HeadShok
QHDST/EBO Headset Cannondale/Coda HeadShok black
HD209/BLK Air filter hood and filter unit for Lefty, Black only
HD210/ Lefty steerer tube plug
8A502/BLK Frame protection bumper
KF354/ Kit, Tacho Mount Lefty Forks
KT040/ Kit, Steerer, X-Long Lefty
KF222/ Kit, Boot, Lefty MAX 140
© 2009 Cannondale Europe • www.cannondale.com
LEFTY MAX 130 PBR Carbon & Alloy version
LEFTY MAx CARboN 130 PbR
SpecificationsID: Large red rebound dial w/ small blue lockout relase button, air valve at bottom, small blue lockout push button inside rebound dial, carbon outer tube.
Year 2008-2009 +
Travel (mm) 130
Damper Oil damped
Spring element Air sprung, Solo Air self adjusting negative spring
Lockout Adjustable lock-out threshold
Rebound External Adjustment
Compatilibities Stems, steering tubes
KITS
ITEM NUMBER DESCRIPTION
KH017/ Fox RLC 130 mm rebound damper
KH011/ Fox RLC upgrade kit
RECOMMENDED STARTING AIR PRESSURE
Lbs Kg Psi Bar
120 54 85 5.8
130 59 90 6.2
140 64 95 6.5
150 68 105 7.2
160 73 120 8.2
170 77 135 9.3
180 82 150 10.3
190 86 165 11.3
200 91 180 12.4
210 95 195 13.4
220 100 205 14.1
PRESSURE LIMITS MINIMUM - 50 psi (3.4 bar) MAXIMUM - 225 psi (15.5 bar)
RECOMMENDED SAG 25 - 30% = (32.5 - 39.0 mm)
KH045/ PBR DIAL Carbon version KH046/ PBR DIAL Alloy version
© 2009 Cannondale Europe • www.cannondale.com
LEFTY MAx CARboN 130 PbR
28.0 Nm, 248 InLbs
9.0 Nm, 80 InLbs
20.0 Nm, 177 InLbs
0.33 Nm, 3 InLbs
0.5 Nm, 4.4 InLbsLoctite™ 222
0.23 Nm, 2.0 InLbs
HD215/
HD209/BLK
KF222/
KH045/KH046/
KT028/
16mm
LEFTY BOLTS
HD011/
KF205/
HD175/BLK
KH044/
KH042/
KH061/
HD226/
KH043/
9.0 Nm, 80 InLbs
KH057/
3.4 Nm, 30 InLbsLoctite™ 242
28.0 Nm, 248 InLbsLoctite™ 242
Loctite™ 401
KITS
ITEM NUMBER DESCRIPTION
KH041/ Kit, Damper, Lefty PBR 130
KH042/ Kit, Seals, PBR 130