fag deep groove ball bearings 6203-2rsr-m-p6-l38t-c3-s1 · fag bearings sales corporation bore...
TRANSCRIPT
FAG Bearings Sales Corporation
Bore Diameter00 10 mm01 12 mm02 15 mm03 17 mm04 - 96 Bore Reference x 5 (mm)/ 500 500 mm
Heat Treat CodeNo Suffix (S0) Heat Stabilized to 302oF (150oC)S1 Heat Stabilized to 392oF (200oC)S2 Heat Stabilized to 482oF (250oC)S3 Heat Stabilized to 572oF (300oC)S4 Heat Stabilized to 662oF (350oC)
Sealing & ShieldingNo Suffix Open BearingC Generation C DesignRSR Standard Rubber Seal (Contact)2RSR 2 Standard Rubber Seals (Contact)RSD Standard Rubber Seals (Non-Contact)2RSD 2 Standard Rubber Seals (Non-Contact)HSR Hycar Seal (Contact)2HSR 2 Hycar Seals (Contact)HSD Hycar Seals (Non-Contact)2HSD 2 Hycar Seals (Non-Contact)VSR Viton Seal (Contact)2VSR 2 Viton Seals (Contact)VSD Viton Seals (Non Contact)2VSD 2 Viton Seals (Non Contact)ZR Metal Shield2ZR 2 Metal Shields
Series60 Extra Light62 Light63 Medium64 Heavy
6203-2RSR-M-P6-L38T-C3-S1
Cage DesignJ Standard Stamped Steel CageJN Riveted Standard Stamped Steel CageTNH Polyamide, Snap-TypeM Machined BrassTVH Glass Fiber Reinforced Polyamide, Snap-TypeY Pressed Brass
Cage TypeNo Suffix Ball GuidedA Outer Ring GuidedB Inner Ring Guided
Grease CodesConsult Grease Code Chart
Radial Clearance ClassC2 Smaller than Normal (CN)CN NormalC3 Greater than Normal (CN)C4 Greater than C3C5 Greater than C4R30.50 Special Radial Clearance
(30 to 50 Microns)
FAG Deep Groove Ball Bearings
Precision ClassISO ABECNo Suffix 1 Normal Precision (PN)P6 3 Better than Normal (PN)P5 5 Better than P6
FAG Bearings Sales Corporation
Precision ClassNo Suffix Normal (PN)No Suffix Universal Design - Normal (PN) with P5
Bore Diameter & Special Width ToleranceP6 Better than Normal (PN)P6 Universal Design – Better than Normal (PN)
with P5 Bore Diameter & Special WidthTolerance
P5 Better than P6P5 Universal Design - Better than P6 with
Special Width tolerance
Internal Bearing DesignSuffix Series Contact AngleNo Suffix 718 30o
71 30o
70 (Bore £ 100 mm) 20o
70 (Bore > 100 mm) 30o
B 72 40o
73 40o
74 40o
Universal Design for Paired MountingNo Suffix Paired Mounting NOT PossibleUA Small Axial Clearance when Paired
(un-mounted) in an “X” or “O” ArrangementUO Zero Clearance when Paired (un-mounted) in
an “X” or “O” ArrangementUL Light Preload when Paired (un-mounted) in
an “X” or “O” ArrangementUM Medium Preload when Paired (un-mounted)
in an “X” or “O” ArrangementUH Heavy Preload when Paired (un-mounted) in
an “X” or “O” ArrangementUA50.100 Special Axial Clearance (un-mounted) for a
Universal Design Bearing Pair(50 to 100 Microns)
7203-B-TVP-P5-UA
Series718719707273
Cage DesignTVP Glass Fiber Reinforced PolyamideMP Machined BrassYP Stamped BrassJP Stamped Steel
Cage GuidanceNo Suffix Ball GuidedA Outer Ring GuidedB Inner Ring Guided
Bore Diameter00 10 mm01 12 mm02 15 mm03 17 mm04 - 96 Bore Reference x 5 (mm)/ 500 500 mm
FAG Single Row AngularContact Ball Bearings
FAG Bearings Sales Corporation
Cage DesignTVH Glass Fiber ReinforcedPolyamideJH Stamped SteelM Machined Brass
GreaseSee Deep Groove Ball Bearings except L943L943 Anti-Corrosion Slush
Preservative
Axial Internal ClearanceC2 Less than Normal (CN)No Suffix Normal (CN)C3 Larger than Normal (CN)C4 Larger than C3A50.100 Special Axial Clearance
(50 to 100 Microns)
Bore Diameter00 10 mm01 12 mm02 15 mm03 17 mm04 - 96 Bore Reference x 5 (mm)/ 500 500 mm
Series32 LightSeries 33 Medium series
Internal DesignNo Suffix Max Type 35o Contact AngleC Max Type 30o Contact Angle
Domestic ProductionB Conrad Type 25o Contact AngleBC Conrad Type 20o Contact Angle
Domestic ProductionBD Conrad Type 30o Contact AngleDA Split Inner Ring 45o Contact Angle
3207-B-2RSR-TVH-P5-L100N-C3
Seals & ShieldsRSR 1 Rubber Seal (Contact)2RSR 2 Rubber Seals (Contact)ZR 1 Metal Shield2ZR 2 Metal Shields
Precision ClassISO ABECNo Suffix 1 Normal Precision (PN)P6 3 Better than Normal (PN) PrecisionP5 5 Better than P6 Precision
FAG Double Row AngularContact Ball Bearings
FAG Bearings Sales Corporation
Bore DesignNo Suffix Cylindrical BoreK Tapered Bore (1:12)
Cage DesignNo suffix Stamped SteelM Machined BrassF Machined SteelTV Polyamide
Grease CodeSee grease code charts
Radial Internal ClearanceC2 Less than Normal (CN)No Suffix Normal (CN)C3 Larger than Normal (CN)C4 Larger than C3R30.50 Special Radial Clearance
(30 to 50 microns)
2208-K-2RS-TVH-L38N-C3
Series12 Light22 Light Wide13 Medium23 Medium Wide
SealsRS 1 Rubber Seal (contact)2RS 2 Rubber Seals (contact)
Bore Diameter00 10 mm01 12 mm02 15 mm03 17 mm04 - 96 Bore Reference (mm)/ 500 500 mm
FAG Double-RowSelf-Aligning Ball Bearings
FAG Bearings Sales Corporation
Bore Diameter/ 4 / 8 4 mm 8 mm00 10 mm01 12 mm02 15 mm03 17 mm04 - 96 Bore Reference x 5 (mm)/ 500 500 mm
Cage DesignNo Suffix Stamped Steel (J or JP)M 2 pc. Machined BrassMP 1 pc. Machined BrassF 2 pc. Machined SteelFP 1 pc. Machined SteelTNP 1 pc. PolyamideTVP Reinforced Polyamide
SeriesSingle Direction Double Direction510 522512 523513 542514 543532533
Precision ClassNo Suffix Normal (PN)P6 Better than Normal (PN)P5 Better than P6P4 Better than P5
51156-FP-P5
FAG ThrustBall Bearings
FAG Bearings Sales Corporation
Bore Diameter00 10 mm01 12 mm02 15 mm03 17 mm04 - 96 Bore Reference x 5 (mm)/ 500 500 mm
Radial Internal ClearanceC2 Less than Normal (CN)No Suffix Normal (CN)C3 Larger than Normal (CN)C4 Larger than C3R80.100 Special Radial Clearance
(80 to 100 microns)
Bearing DesignNU 1 Row, No Lips I.R., 2 Lips O.R.NJ 1 Row, 1 Lip I.R., 2 Lips O.R.NUP 1 Row, 1 Lip + Separable Lip I.R.
2 Lip O.R.N 1 Row, 2 Lips I.R., No Lips O.R.NJ + HJ 1 Row, 1 Lip + Angle Ring I.R.
2 Lips O.R.
NU2336-EX-M1-C4
Series10 Extra Light Series2 Light Series22 Light Wide Series3 Medium Series23 Medium Wide Series4 Heavy Series
Internal Bearing DesignNo Suffix Standard CapacityE High (Extra) CapacityEX High (Extra) Capacity
Internal Design per DIN 5412
Cage DesignF Machined SteelJP Stamped SteelJP1 Stamped Steel (“E” Design)M Machined BrassM1 Machined Brass (“E” Design)TVP Glass Fiber Reinforced
Polyamide
Cage GuidanceNo Suffix Roller GuidedA Out Ring GuidedB Inner Ring Guided
FAG Single RowCylindrical Roller Bearings
FAG Bearings Sales Corporation
Precision ClassNo Suffix Normal (PN) ToleranceP6 Better than Normal (PN)P5 Better than P6 Tolerance
Cage GuidanceNo Suffix Roller GuidedA Housing GuidedB Shaft Guided
Cage DesignJ Stamped SteelTVP Glass Fiber ReinforcedPolyamideM 2 pc. Machined BrassMP 1 pc. Machined BrassF 2 pc. Machined SteelFP 1 pc. Machined SteelL 2 pc. Light Metal AlloyLP 1 pc. Light Metal Alloy
81126-M-P5
Series810811812813814
Cage Lubrication SlotsS Lubrication slots in
Cage Guidance Surface
FAG Cylindrical RollerThrust Bearings
Bore Diameter00 1001 1202 1503 1704 - 96 Bore Reference x 5 (mm)/ 500 500 mm
FAG Bearings Sales Corporation
31312-A-M-P5-N11CA-A80-120
SuffixesA Modified Internal DesignB Modified Internal Design,
Increased Contact AngleX Boundary Dimensions
Adapted to InternationalStandards (ISO)
XA Boundary DimensionsAdapted to InternationalInternal Design
Bore Diameter00 10 mm01 12 mm02 15 mm03 17 mm04 - 96 Bore reference x 5 (mm)/ 500 500 mm
Note: Series 320X, 329, 330, 331, 332 with bore diameters of up to 200 mm have the P6X tolerance as standard
Series329320X330331302322B303313313X323323B
Cage DesignJP Stamped Steel Cage (No Suffix)F Machined Steel (No Suffix)M Machined BrassTNP Polyamide (No Suffix)TVP Glass Fiber Reinforced
Polyamide (No Suffix)
Precision ClassNo Suffix Normal (PN)P6X Normal (PN) Tolerance / Width
Tolerance Better than Normal(PN) Tolerance
P5 Better than P6X ToleranceP4 Better than P5 Tolerance
FAG Metric TaperedRoller Bearings
Matching SpecificationsA25.50 Axial Clearance
(25 to 50 microns)VA25.50 Preload Range
(25 to 50 microns)N11BA / N11BBN11BC / N11BDN11CA / N11CBN11CC
MatchingSpecifications
FAG Bearings Sales Corporation
Bore Diameter02 15 mm03 17 mm04 - 64 Bore Reference x 5 (mm)
20222-K-MB-C3
Bearing Series202 Light Series203 Medium Series204 Heavy Series
Bore DesignNo Suffix Cylindrical BoreK Tapered Bore (1:12)
Cage GuidanceNo Suffix Roller GuidedA Outer Ring GuidedB Inner Ring Guided
Cage DesignNo Suffix (J) Stamped SteelT (TVP) Glass Fiber
Reinforced PolyamideM Machined Brass
Radial Internal ClearanceC2 Less than Normal (CN)No Suffix Normal (CN)C3 Larger than Normal (CN)C4 Larger than C3R100.200 Special Radial Clearance
(100 to 200 microns)
FAG Barrel Roller Bearings
FAG Bearings Sales Corporation
22318-E1A-K-M-C3
Bore Diameter00 10 mm01 12 mm02 15 mm03 17 mm04 - 96 Bore Reference x 5 (mm)/ 500 500 mm
Cage DesignNo Suffix Stamped Steel
(“E” Design)J Stamped SteelF Machined SteelL Light Metal AlloyM Machined BrassTVP Glass Fiber Reinforced
PolyamideYP Stamped Brass
Bearing Design239 Extremely Light, Wide230 Extra Light, Wide240 Extra Light, Extra Wide231 Extra Light / Light, Wide241 Extra Light / Light, Extra Wide222 Light232 Light, Wide213 Medium, Narrow223 Medium233 Heavy
Radial Internal ClearanceC2 Less than normal (CN)No Suffix Normal (CN)C3 Lager than Normal (CN)C4 Larger than C3R100.120 Special Radial Clearance
(100 – 120 microns)
Cage GuidanceNo Suffix Roller GuidedA Outer Ring GuidedB Inner Ring Guided
Bore DesignNo Suffix Cylindrical BoreK Tapered Bore (1:12)K30 Tapered Bore (1:30)
Lubrication Hole FeatureS Lubrication Groove & Holes,
O.R. (not indicated for bearingO.D. > 320 mm, or “E” type steelcage design)
SY Lubrication Holes, O.R.
Internal Bearing DesignNo Suffix Standard CapacityE High (Extra) CapacityE1 High (Extra) CapacityA Internal Design ModificationB Internal Design Modification
FAG Double RowSpherical Roller Bearings
FAG Bearings Sales Corporation
Series292293294
CagesNo Suffix Stamped SteelMB Machined Brass Cage
Shaft Washer GuidedMBS Machined Brass Cage
Roller Guided withLubrication Feature
Internal Bearing DesignE High (Extra) CapacityE1 X-life, High Capacity
Bore Diameter12 - 96 Bore Reference x 5 mm/ 500 500 mm
29248-E-MB
FAG Spherical RollerThrust Bearings
FAG Bearings Sales Corporation
No Suffix Normal (PN)P6 Better than Normal (PN)P5 Better than P6
C2 Less than Normal (CN)CN Normal (no suffix)C3 Larger than Normal (CN)C4 Larger than C3T42A Special Axial Clearance
(Consult FAG)
Bore Diameter00 10 mm01 12 mm02 15 mm03 17 mm04 - 96 Bore Reference x 5 (mm)/ 500 ® 500 mm ®
N1: 1 Locating Groove in the Outer RingN2: 2 Locating Grooves in the Outer Ring
Locating Groove
FAG Four PointContact Ball Bearings
QJ318-N2-MPA-P6-C3
Prefix
Q Split Outer RingQJ Split Inner Ring
Series
2 Light Series3 Medium Series4 Heavy Series
Axial Internal Clearance
Cage Design
MP Machined BrassTVP Glass Fiber Reinforced
Polyamide
Precision Class
Cage Guidance
No Suffix Ball GuidedA Outer Ring GuidedB Inner Ring Guided