facing on the centre lathe
DESCRIPTION
Facing on the Centre Lathe. Centre Lathe. Safety Guard. Chuck. Tailstock. The picture on the left shows a Centre Lathe which is used for turning metals. Bed. Headstock. Compound Slide. Cross Slide. Toolpost. Saddle wheel. The main parts are as shown. Emergency Stop. Facing a Bar. - PowerPoint PPT PresentationTRANSCRIPT
![Page 1: Facing on the Centre Lathe](https://reader035.vdocuments.us/reader035/viewer/2022062314/56813be5550346895da51349/html5/thumbnails/1.jpg)
Facing on the Centre Lathe
![Page 2: Facing on the Centre Lathe](https://reader035.vdocuments.us/reader035/viewer/2022062314/56813be5550346895da51349/html5/thumbnails/2.jpg)
CentreLathe
EmergencyStop
Tailstock
Bed
Chuck
Safety Guard
Toolpost
Headstock
The picture on the left shows a Centre Lathe which is used for turning metals
The main parts are as shown
Cross Slide
Saddle wheel
Compound Slide
![Page 3: Facing on the Centre Lathe](https://reader035.vdocuments.us/reader035/viewer/2022062314/56813be5550346895da51349/html5/thumbnails/3.jpg)
First of all fix the bar in the chuck with the chuck key.
Facing a Bar
![Page 4: Facing on the Centre Lathe](https://reader035.vdocuments.us/reader035/viewer/2022062314/56813be5550346895da51349/html5/thumbnails/4.jpg)
To Face the end of this bar start by lowering the Safety Guard
Facing a Bar
![Page 5: Facing on the Centre Lathe](https://reader035.vdocuments.us/reader035/viewer/2022062314/56813be5550346895da51349/html5/thumbnails/5.jpg)
Now use the Saddle Wheel to move the tool closer to the workpiece
Facing a Bar
![Page 6: Facing on the Centre Lathe](https://reader035.vdocuments.us/reader035/viewer/2022062314/56813be5550346895da51349/html5/thumbnails/6.jpg)
Next use the Compound slide to move the toolpost in until it is ready to cut
Facing a Bar
![Page 7: Facing on the Centre Lathe](https://reader035.vdocuments.us/reader035/viewer/2022062314/56813be5550346895da51349/html5/thumbnails/7.jpg)
Now switch On the lathe
Facing a Bar
![Page 8: Facing on the Centre Lathe](https://reader035.vdocuments.us/reader035/viewer/2022062314/56813be5550346895da51349/html5/thumbnails/8.jpg)
Finally use the cross slide to pass the lathe tool across the face of the bar taking a fine even paced cut.
Facing a Bar
![Page 9: Facing on the Centre Lathe](https://reader035.vdocuments.us/reader035/viewer/2022062314/56813be5550346895da51349/html5/thumbnails/9.jpg)
Switch the Lathe Off
Facing a Bar
![Page 10: Facing on the Centre Lathe](https://reader035.vdocuments.us/reader035/viewer/2022062314/56813be5550346895da51349/html5/thumbnails/10.jpg)
Facing a Bar
Use the Saddle wheel to return the lathe tool to its original position then lift the guard.
![Page 11: Facing on the Centre Lathe](https://reader035.vdocuments.us/reader035/viewer/2022062314/56813be5550346895da51349/html5/thumbnails/11.jpg)
This process may have to be repeated more than once
![Page 12: Facing on the Centre Lathe](https://reader035.vdocuments.us/reader035/viewer/2022062314/56813be5550346895da51349/html5/thumbnails/12.jpg)
Well Done
Process Completed
![Page 13: Facing on the Centre Lathe](https://reader035.vdocuments.us/reader035/viewer/2022062314/56813be5550346895da51349/html5/thumbnails/13.jpg)
CentreLathe
EmergencyStop
Tailstock
Bed
Chuck
Safety Guard
Toolpost
Headstock
The picture on the left shows a Centre Lathe which is used for turning metals
The main parts are as shown
Cross Slide
Saddle wheel
Compound Slide
Back
![Page 14: Facing on the Centre Lathe](https://reader035.vdocuments.us/reader035/viewer/2022062314/56813be5550346895da51349/html5/thumbnails/14.jpg)
Wrong
Click here to try again