f115 / lf115 owner's manual - · pdf filef115 lf115 owner’s manual 68v-28199-18...
TRANSCRIPT
F115LF115
OWNER’S MANUAL
68V-28199-18
U.S.A.EditionLIT-18626-07-13
68V-9-18 Hyoshi 06.2.24 9:19 ページ 1
EMU25060
ZMU01690
Read this owner’s manual carefully before operating your outboard motor.
68V-9-18 Hyoshi 06.2.24 9:20 ページ 2
Important manual information
EMU31280
To the owner
Thank you for choosing a Yamaha outboardmotor. This Owner’s Manual contains infor-mation needed for proper operation, mainte-nance and care. A thorough understandingof these simple instructions will help you ob-tain maximum enjoyment from your newYamaha. If you have any question about theoperation or maintenance of your outboardmotor, please consult a Yamaha dealer.In this Owner’s Manual particularly importantinformation is distinguished in the followingways.
The Safety Alert Symbol meansATTENTION! BECOME ALERT! YOURSAFETY IS INVOLVED!
WARNING
EWM00780
Failure to follow WARNING instructionscould result in severe injury or death tothe machine operator, a bystander, or aperson inspecting or repairing the out-
board motor.
CAUTION:
ECM00700
A CAUTION indicates special precautionsthat must be taken to avoid damage to the
outboard motor.
NOTE:
A NOTE provides key information to make
procedures easier or clearer.
Yamaha continually seeks advancements inproduct design and quality. Therefore, whilethis manual contains the most current prod-uct information available at the time of print-ing, there may be minor discrepanciesbetween your machine and this manual. Ifthere is any question concerning this manu-
al, please consult your Yamaha dealer.
NOTE:
The F115TR, LF115TR and the standard ac-cessories are used as a base for the expla-nations and illustrations in this manual.Therefore some items may not apply to ev-
ery model.
EMU25110
F115, LF115OWNER’S MANUAL
©2006 by Yamaha Motor Corporation, USA1st edition, March 2006
All rights reserved.Any reprinting or unauthorized usewithout the written permission ofYamaha Motor Corporation, USA
is expressly prohibited.Printed in Japan
P/N LIT-18626-07-13
Table of contents
General information .......................... 1
Identification numbers record.......... 1
Outboard motor serial number .......... 1Key number....................................... 1
Emission control information ........... 1
North American models..................... 1Star labels ......................................... 2
Safety information ........................... 3Important labels............................... 4
Warning labels .................................. 4
Basic boating rules (Rules of the road) .............................................. 5
Steering and sailing rules and sound signals.................................. 5
Rules when encountering vessels .... 5Other special situations..................... 6
Fueling instructions ......................... 8
Gasoline............................................ 9Engine oil .......................................... 9
Battery requirement....................... 10
Battery specifications ...................... 10
Propeller selection......................... 10Start-in-gear protection ................. 11
Basic components .......................... 12
Main components.......................... 12
Remote control................................ 13Remote control lever ....................... 14Neutral interlock trigger ................... 14Neutral throttle lever........................ 14Free accelerator .............................. 15Tiller handle .................................... 15Gear shift lever................................ 15Throttle grip ..................................... 16Throttle indicator ............................. 16Throttle friction adjuster................... 16Engine stop lanyard switch ............. 17Engine stop button .......................... 18Main switch ..................................... 18Steering friction adjuster ................. 18Power trim and tilt switch on remote
control or tiller handle ................... 19Power trim and tilt switch on bottom
engine cowling .............................. 19Power trim and tilt switches (twin
binnacle type) ............................... 20
Trim tab with anode.........................20Tilt support lever for power trim and
tilt or hydro tilt model.....................21Top cowling lock lever
(pull up type) .................................21Flushing device ...............................22Water separator ..............................22Tachometer .....................................22Digital tachometer ...........................22Low oil pressure warning
indicator ........................................23Low oil pressure warning
indicator ........................................23Overheat warning indicator .............24Overheat warning indicator (digital
type) ..............................................24Speedometer (digital type) ..............24Trim meter .......................................25Trim meter (digital type) ..................25Hour meter (digital type)..................25Trip meter ........................................26Clock ...............................................26Fuel gauge ......................................26Fuel warning indicator .....................27Low battery voltage warning
indicator ........................................27Fuel management meter .................27Fuel flow meter................................28Fuel consumption meter..................28Fuel economy..................................28Twin-engine speed synchronizer ....29Command link multifunction
meters ...........................................30Tachometer unit ..............................30Speed & fuel meter unit...................33Speedometer unit ............................34Fuel management meter .................35
Warning system ............................ 36
Overheat warning (twin engines) ....36Low oil pressure warning ................37
Operation ......................................... 38
Installation..................................... 38
Mounting the outboard motor ..........38
Breaking in engine ........................ 39
Procedure for 4-stroke models........39
Table of contents
Preoperation checks ..................... 40
Fuel ................................................. 40Controls........................................... 40Engine............................................. 40Checking the engine oil level .......... 40
Filling fuel ...................................... 41
Ring Free Fuel Additive .................. 41
Operating engine........................... 41
Feeding fuel .................................... 41Starting engine................................ 42
Warming up engine ....................... 45
Manual start and electric start models .......................................... 45
Shifting .......................................... 45
Forward (tiller handle and remote control models) ............................. 45
Reverse (automatic reverse lock and power trim and tilt models)..... 46
Stopping engine ............................ 47
Procedure ....................................... 47
Trimming outboard motor.............. 48
Adjusting trim angle ........................ 48Adjusting boat trim .......................... 49
Tilting up and down ....................... 50
Procedure for tilting up (power trim and tilt models / power tilt models) ......................................... 51
Procedure for tilting down (power trim and tilt models / power tilt models) ......................................... 52
Cruising in shallow water .............. 53
Power trim and tilt models / power tilt models...................................... 53
Cruising in other conditions........... 54
Maintenance..................................... 56
Specifications ................................ 56Transporting and storing outboard
motor ........................................... 57
Storing outboard motor ................... 57Procedure ....................................... 58Lubrication ...................................... 59Cleaning and anticorrosion
measures ...................................... 59Battery care..................................... 59Flushing power unit ......................... 60
Cleaning the outboard motor...........61Checking painted surface of
motor.............................................61
Periodic maintenance ................... 61
Replacement parts ..........................61Maintenance chart...........................62Maintenance chart (additional) ........63Greasing..........................................64Cleaning and adjusting spark
plug ...............................................64Checking fuel system ......................65Inspecting idling speed....................66Changing engine oil ........................66Checking wiring and connectors .....68Exhaust leakage..............................68Water leakage .................................68Engine oil leakage...........................68Checking power trim and tilt
system...........................................68Checking propeller ..........................69Removing the propeller ...................70Installing the Propeller.....................70Changing gear oil ............................71Inspecting and replacing
anode(s)........................................72Checking battery (for electric start
models) .........................................73Connecting the battery ....................73Disconnecting the battery................74Checking top cowling ......................74Coating the boat bottom..................74
Trouble Recovery............................ 75
Troubleshooting ............................ 75Temporary action in emergency ... 78
Impact damage ...............................78Running single engine.....................78Replacing fuse ................................79Power trim and tilt / power tilt will
not operate....................................79Water separator warning indicator
blinks while cruising ......................80Starter will not operate ....................81Emergency starting engine .............82
Treatment of submerged motor .... 83
Procedure........................................83
Table of contents
Consumer information.................... 84
Important warranty information for U.S.A. and Canada ..................... 84
YAMAHA MOTOR CORPORATION, U.S.A. FOUR-STROKE OUTBOARD MOTOR THREE-YEAR LIMITED WARRANTY ................................ 86
IMPORTANT WARRANTY INFORMATION IF YOU USE YOUR YAMAHA OUTSIDE THE USA OR CANADA ...................... 88
1
General information
EMU25170
Identification numbers record
EMU25183
Outboard motor serial number
The outboard motor serial number isstamped on the label attached to the portside of the clamp bracket.Record your outboard motor serial number inthe spaces provided to assist you in orderingspare parts from your Yamaha dealer or forreference in case your outboard motor is sto-len.
EMU25190
Key number
If a main key switch is equipped with the mo-tor, the key identification number is stampedon your key as shown in the illustration.Record this number in the space provided forreference in case you need a new key.
EMU25221
Emission control information
EMU25230
North American models
This engine conforms to U.S. EnvironmentalProtection Agency (EPA) regulations for ma-rine SI engines. See the label affixed to yourengine for details.
EMU31560
Approval label of emission control certif-icate
This label is attached to the bottom cowling.New Technology; (4-stroke) MFI
1. Outboard motor serial number location
1. Key number
1. Approval label location
ZMU04276
1
General information
2
EMU25262
Manufactured date label
This label is attached to the clamp bracket orthe swivel bracket.
EMU25272
Star labels
Your outboard motor is labeled with a Cali-fornia Air Resources Board (CARB) star la-bel. See below for a description of your
particular label.
EMU25280
One Star—Low Emission
The one-star label identifies engines thatmeet the Air Resources Board’s 2001 ex-haust emission standards. Engines meetingthese standards have 75% lower emissionsthan conventional carbureted two-stroke en-gines. These engines are equivalent to theU.S. EPA’s 2006 standards for marine en-gines.
EMU25290
Two Stars—Very Low Emission
The two-star label identifies engines thatmeet the Air Resources Board’s 2004 ex-haust emission standards. Engines meetingthese standards have 20% lower emissionsthan One Star-Low-Emission engines.
1. Manufactured date label location
ZMU04277
1
ZMU04776
ZMU01702
General information
3
EMU25300
Three Stars—Ultra Low Emission
The three-star label identifies engines thatmeet the Air Resources Board’s 2008 ex-haust emission standards. Engines meetingthese standards have 65% lower emissionsthan One Star-Low-Emission engines.
EMU25362
Safety information
�
Before mounting or operating the outboardmotor, read this entire manual. Reading itshould give you an understanding of themotor and its operation.
�
Before operating the boat, read any own-er’s or operator’s manuals supplied with itand all labels. Be sure you understandeach item before operating.
�
Do not overpower the boat with this out-board motor. Overpowering the boat couldresult in loss of control. The rated power of
the outboard should be equal to or lessthan the rated horsepower capacity of theboat. If the rated horsepower capacity ofthe boat is unknown, consult the dealer orboat manufacturer.
�
Do not modify the outboard. Modificationscould make the motor unfit or unsafe touse.
�
Incorrect propeller selection and incorrectuse may not only cause engine damage,but also adversely affect fuel consumption.Consult your dealer for correct use.
�
Never operate after drinking alcohol or tak-ing drugs. About 50% of all boating fatali-ties involve intoxication.
�
Have an approved personal flotation de-vice (PFD) on board for every occupant. Itis a good idea to wear a PFD wheneverboating. At a minimum, children and non-swimmers should always wear PFDs, andeveryone should wear PFDs when thereare potentially hazardous boating condi-tions.
�
Gasoline is highly flammable, and its va-pors are flammable and explosive. Handleand store gasoline carefully. Make surethere are no gas fumes or leaking fuel be-fore starting the engine.
�
This product emits exhaust gases whichcontain carbon monoxide, a colorless,odorless gas which may cause brain dam-age or death when inhaled. Symptoms in-clude nausea, dizziness, and drowsiness.Keep cockpit and cabin areas well ventilat-ed. Avoid blocking exhaust outlets.
�
Check throttle, shift, and steering for prop-er operation before starting the engine.
�
Attach the engine stop switch lanyard cordto a secure place on your clothing, or yourarm or leg while operating. If you acciden-tally leave the helm, the cord will pull from
ZMU01703
ZMU01704
General information
4
the switch, stopping the engine.
�
Know the marine laws and regulationswhere you will be boating—and obeythem. For basic boating rules, see “Rulesof the road” on page 5.
�
Stay informed about the weather. Checkweather forecasts before boating. Avoidboating in hazardous weather.
�
Tell someone where you are going: leavea Float Plan with a responsible person. Besure to cancel the Float Plan when you re-turn.
�
Use common sense and good judgmentwhen boating. Know your abilities, and besure you understand how your boat han-dles under the different boating conditionsyou may encounter. Operate within yourlimits, and the limits of your boat. Alwaysoperate at safe speeds, and keep a carefulwatch for obstacles and other traffic.
�
Always watch carefully for swimmers dur-ing the engine operation.
�
Stay away from swimming areas.
�
When a swimmer is in the water near youshift into neutral and shut off the engine.
�
Do not illegally discard empty containersused to replace or replenish oil. For thecorrect processing of empty containers,consult the dealer where you purchasedthe oil.
�
When replacing oils used to lubricate theproduct (engine or gear oil), be sure towipe away any spilt oil. Never pour oil with-out using a funnel or similar device. If nec-essary, verify the necessary replacementprocedure with the dealer.
�
Never illegally discard (dump) the product.Yamaha recommends consulting the deal-er on discarding the product.
Be informed about boating safety. Additionalpublications and information can be obtained
from many organizations, including the fol-lowing:
United States Coast Guard
Consumer Affairs Staff (G-BC) Office of Boating, Public, and Consumer Af-fairs U.S. Coast Guard Headquarters Washington, D.C. 20593-0001 Boating Safety Hotline: 1-800-368-5647
National Marine Manufacturers Associa-tion (NMMA)
401 N. Michigan Ave. Chicago, Il 60611
Marine Retailers Association of America
155 N. Michigan Ave. Chicago, Il 60601
EMU25382
Important labels
EMU25395
Warning labels
EMU25401
Label
WARNING
EWM01260
�
Be sure shift control is in neutral beforestarting engine. (except 2HP)
�
Do not touch or remove electrical partswhen starting or during operation.
�
Keep hands, hair, and clothes awayfrom flywheel and other rotating parts
while engine is running.
ZMU04275
General information
5
EMU25413
Label (counter rotation models)
WARNING
EWM01281
Use only a counterclockwise rotationpropeller with this engine.Counterclockwise propellers are markedwith a letter “L” after the size indication.The wrong type of propeller could causethe boat to go in an unexpected direction,
which could lead to an accident.
EMU25500
Basic boating rules (Rules of the road)
Just as there are rules which apply when youare driving on streets and high ways, thereare waterway rules which apply when youare driving your boat. These rules are usedinternationally, and are also enforced by theUnited States Coast Guard and local agen-cies. You should be aware of these rules,and follow them whenever you encounteranother vessel on the water.Several sets of rules prevail according togeographic location, but are all basically thesame as the International Rules of the Road.The rules presented here in your Owner’sManual are condensed, and have been pro-vided for your convenience only. Consultyour local U.S. Coast Guard Auxiliary or De-partment of Motor Vehicles for a completeset of rules governing the waters in whichyou will be using your boat.
EMU25510
Steering and sailing rules and sound signals
Whenever two vessels on the water meetone another, one vessel has the right-of-way; it is called the “stand-on” vessel. Thevessel which does not have the right-of-wayis called the “give-way” or “burdened” vessel.
These rules determine which vessel has theright-of-way, and what each vessel shoulddo.
Stand-on vessel
The vessel with the right-of-way has the dutyto continue its course and speed, except toavoid an immediate collision. When youmaintain your direction and speed, the othervessel will be able to determine how best toavoid you.
Give-way vessel
The vessel which does not have the right-of-way has the duty to take positive and timelyaction to stay out of the way of the Stand-Onvessel. Normally, you should not cross infront of the vessel with the right-of-way. Youshould slow down or change directions brief-ly and pass behind the other vessel. Youshould always move in such a way that theoperator of the other vessel can see whatyou are doing.
“The general prudential rule”
This rule is called Rule 2 in the InternationalRules and says,“In obeying and construing these rules dueregard shall be had to all dangers of naviga-tion and collision, and to any special circum-stances, which may render a departure fromthe above rules necessary in order to avoidimmediate danger.”In other words, follow the standard rules ex-cept when a collision will occur unless bothvessels try to avoid each other. If that is thecase, both vessels become “Give-Way” ves-sels.
EMU25520
Rules when encountering vessels
There are three main situations which youmay encounter with other vessels whichcould lead to a collision unless the SteeringRules are followed:
Meeting:
(you are approaching another ves-
General information
6
sel head-on)
Crossing:
(you are traveling across the oth-er vessel’s path)
Overtaking:
(you are passing or beingpassed by another vessel)In the following illustration, your boat is in thecenter. You should give the right-of-way toany vessels shown in white area (you are theGive-Way vessel). Any vessels in the shad-ed area must yield to you (they are the Give-Way vessels). Both you and the meetingvessel must alter course to avoid each other.
Meeting
If you are meeting another power vesselhead on, and are close enough to run the riskof collision, neither of you has the right-of-way! Both of you should alter course to avoidan accident. You should keep the other ves-sel on your port (left) side. This rule doesn’tapply if both of you will clear one another ifyou continue on your set course and speed.
Crossing
When two power driven vessels are crossingeach other’s path close enough to run therisk of collision, the vessel which has the oth-er on the starboard (right) side must keep outof the way of the other. If the other vessel ison your right, you must keep out of its way;you are the Give-Way vessel. If the othervessel is on your port (left) side, rememberthat you should maintain course and direc-tion, provided the other vessel gives you theright-of-way as it should.
Overtaking
If you are passing another vessel, you arethe “Give-Way” vessel. This means that theother vessel is expected to maintain itscourse and speed. You must stay out of itsway until you are clear of it. Likewise, if an-other vessel is passing you, you shouldmaintain your speed and direction so that theother vessel can steer itself around you.
EMU25530
Other special situations
There are three other rules you should beaware of when driving your boat around oth-er vessels.
Narrow channels and bends
When navigating in narrow channels, youshould keep to the right when it is safe andpractical to do so. If the operator of a power-driven vessel is preparing to go around a
General information
7
bend that may obstruct the view of other wa-ter vessels, the operator should sound a pro-longed blast on the whistle (4 to 6 seconds).If another vessel is around the bend, it tooshould sound the whistle. Even if no reply isheard, however, the vessel should still pro-ceed around the bend with caution. If younavigate such waters with your boat, you willneed to carry a portable air horn, availablefrom local marine supply stores.
Fishing vessel right-of-way
All vessels which are fishing with nets, linesor trawls are considered to be “fishing ves-sels” under the International Rules. Vesselswith trolling lines are not considered fishingvessels. Fishing vessels have the right-of-way regardless of position. Fishing vesselscannot, however, impede the passage ofother vessels in narrow channels.
Sailing vessel right-of-way
Sailing vessels should normally be given theright-of-way. The exceptions to this are:1. When the sailing vessel is overtaking
the power-driven vessel, the power-driv-en vessel has the right-of-way.
2. Sailing vessels should keep clear of anyfishing vessel.
3. In a narrow channel, a sailing vesselshould not hamper the safe passage ofa power-driven vessel which can navi-gate only in such a channel.
Reading buoys and other markers
The waters of the United states are markedfor safe navigation by the lateral system ofbuoyage. Simply put, buoys and markershave an arrangement of shapes, colors,numbers and lights to show which side of thebuoy a boater should pass on when navigat-ing in a particular direction. The markings onthese buoys are oriented from the perspec-tive of being entered from seaward (the boat-
er is going towards the port). This means thatred buoys are passed on the starboard(right) side when proceeding from open wa-ter into port, and black buoys are to port (left)side. When navigating out of port, your posi-tion with respect to the buoys should be re-versed; red buoys should be to port andblack buoys to starboard.Many bodies of water used by boaters areentirely within the boundaries of a particularstate. The Uniform State Waterway MarkingSystem has been devised for these waters.This system uses buoys and signs with dis-tinctive shapes and colors to show regulato-ry or advisory information. These markersare white with black letters and orangeboarders. They signify speed zones, restrict-ed areas, danger areas, and general infor-mation.Remember, markings may vary by geo-graphic location. Always consult local boat-ing authorities before driving your boat inunfamiliar waters.
General information
8
EMU25540
Fueling instructions
WARNING
EWM00010
GASOLINE AND ITS VAPORS ARE HIGH-LY FLAMMABLE AND EXPLOSIVE!
�
Do not smoke when refueling, and keep
away from sparks, flames, or othersources of ignition.
�
Stop engine before refueling.
�
Refuel in a well-ventilated area. Refuelportable fuel tanks off the boat.
�
Take care not to spill gasoline. If gaso-line spills, wipe it up immediately with
ZMU01708
General information
9
dry rags.
�
Do not overfill the fuel tank.
�
Tighten the filler cap securely after re-fueling.
�
If you should swallow some gasoline,inhale a lot of gasoline vapor, or getgasoline in your eyes, get immediatemedical attention.
�
If any gasoline spills onto your skin, im-mediately wash with soap and water.Change clothing if gasoline spills on it.
�
Touch the fuel nozzle to the filler open-ing or funnel to help prevent electro-
static sparks.
CAUTION:
ECM00010
Use only new clean gasoline which hasbeen stored in clean containers and is notcontaminated with water or foreign mat-
ter.
EMU25570
Gasoline
If knocking or pinging occurs, use a differentbrand of gasoline or premium unleaded fuel.
Gasohol
There are two types of gasohol: gasohol con-taining ethanol and that containing metha-nol. Gasohol containing ethanol can be usedif ethanol content does not exceed 10% andthe fuel meets minimum octane ratings.Yamaha does not recommended gasoholcontaining methanol because it can causefuel system damage or engine performanceproblems.
EMU31440
Engine oil
NOTE:
If the recommended engine oil grades arenot available, select an alternative from thefollowing chart according to the average
temperatures in your area.
CAUTION:
ECM01050
All 4-stroke engines are shipped from the
factory without engine oil.
Recommended gasoline:Regular unleaded gasoline with a min-imum octane rating of 86 (Pump Oc-tane Number) = (R+M)/2
Recommended engine oil:YAMALUBE 4-M FC-W oil or 4-stroke motor oil with a combination of the fol-lowing SAE and API oil classifications
Engine oil type SAE:10W-30 or 10W-40
Engine oil grade API:SE, SF, SG, SH, SJ, SL
Engine oil quantity (excluding oil filter):4.3 L (4.55 US qt) (3.78 Imp.qt)
General information
10
EMU25700
Battery requirement
CAUTION:
ECM01060
Do not use a battery that does not meetthe specified capacity. If a battery whichdoes not meet specifications is used, theelectric system could perform poorly orbe overloaded, causing electric system
damage.
For electric start models, choose a batterywhich meets the following specifications.
EMU25711
Battery specifications
NOTE:
The engine cannot be started if battery volt-
age is too low.
EMU25742
Propeller selection
The performance of your outboard motor willbe critically affected by your choice of propel-
ler, as an incorrect choice could adverselyaffect performance and could also seriouslydamage the motor. Engine speed dependson the propeller size and boat load. If enginespeed is too high or too low for good engineperformance, this will have an adverse effecton the engine.Yamaha outboard motors are fitted with pro-pellers chosen to perform well over a rangeof applications, but there may be uses wherea propeller with a different pitch would bemore appropriate. For a greater operatingload, a smaller-pitch propeller is more suit-able as it enables the correct engine speedto be maintained. Conversely, a larger-pitchpropeller is more suitable for a smaller oper-ating load.Yamaha dealers stock a range of propellers,and can advise you and install a propeller onyour outboard that is best suited to your ap-plication.
NOTE:
Select a propeller which will allow the engineto reach the middle or upper half of the oper-ating range at full throttle with the maximumboat load. If operating conditions such aslight boat loads then allow the engine r/min to
Minimum cold cranking amps (CCA/SAE):
380.0 AMinimum marine cranking amps (MCA/ABYC):
502.0 AMinimum reserve capacity (RC/SAE):
124 minutes
ZMU01710
1. Propeller diameter in inches2. Propeller pitch in inches3. Type of propeller (propeller mark)
ZMU04608
-x1 2 3
General information
11
rise above the maximum recommendedrange, reduce the throttle setting to maintain
the engine in the proper operating range.
For instructions on propeller removal and in-stallation, see page 69.
EMU25770
Start-in-gear protection
Yamaha outboard motors or Yamaha-ap-proved remote control units are equippedwith start-in-gear protection device(s). Thisfeature permits the engine to be started onlywhen it is in neutral. Always select neutralbefore starting the engine.
12
Basic components
EMU25799
Main componentsNOTE:
* May not be exactly as shown; also may not be included as standard equipment on all mod-
els.
F115, LF115
1
2
2
3
4
56
7
8
9
11
12 13 14
15 16
17 18 19
ZMU04773
10
1. Top cowling2. Top cowling lock lever(s)3. Drain screw4. Anti-cavitation plate5. Trim tab (anode)6. Propeller*7. Cooling water inlet8. Anode9. Flushing device10. Water separator11. Power trim and tilt switch12. Remote control box (side mount type)*13. Remote control box (binnacle mount type)*14. Switch panel (for use with binnacle type)*
15. Tachometer*16. Trim meter*17. Digital speedometer*18. Digital tachometer*19. Fuel management meter*
Basic components
13
EMU26180
Remote control
The remote control lever actuates both theshifter and the throttle. The electrical switch-es are mounted on the remote control box.
1
4 6
32
5
ZMU05429
1. Tachometer unit (Square type)*2. Tachometer unit (Round type)*3. Speedometer unit (Square type)*4. Speed & fuel meter unit (Square type)*5. Speed & fuel meter unit (Round type)*6. Fuel management meter (Square type)*
1. Power trim and tilt switch2. Remote control lever3. Neutral interlock trigger4. Neutral throttle lever5. Main switch / choke switch6. Engine stop lanyard switch7. Throttle friction adjuster
Basic components
14
EMU26190
Remote control lever
Moving the lever forward from the neutral po-sition engages forward gear. Pulling the le-ver back from neutral engages reverse. Theengine will continue to run at idle until the le-ver is moved about 35° (a detent can be felt).Moving the lever farther opens the throttle,and the engine will begin to accelerate.
EMU26201
Neutral interlock trigger
To shift out of neutral, first pull the neutral in-terlock trigger up.
EMU26211
Neutral throttle lever
To open the throttle without shifting into ei-ther forward or reverse, put the remote con-trol lever in the neutral position and lift theneutral throttle lever.
1. Remote control lever2. Power trim and tilt switch3. Free accelerator4. Throttle friction adjuster
1. Neutral “ ”
2. Forward “ ”
3. Reverse “ ”4. Shift5. Fully closed6. Throttle7. Fully open
23
21
4
ZMU04569
1. Neutral “ ”
2. Forward “ ”
3. Reverse “ ”4. Shift5. Fully closed6. Throttle7. Fully open
1. Neutral interlock trigger
N1F
7
6
2R
34 4
65
7
5
ZMU04573
Basic components
15
NOTE:
The neutral throttle lever will operate onlywhen the remote control lever is in neutral.The remote control lever will operate onlywhen the neutral throttle lever is in the closed
position.
EMU26232
Free accelerator
To open the throttle without shifting into ei-ther forward or reverse, push the free accel-erator button and move the remote controllever.
NOTE:
�
The free accelerator button can only be
used when the remote control lever is inthe neutral position.
�
After the button is pushed, the throttle be-gins to open after the remote control leveris moved at least 35°.
�
After using the free accelerator, return theremote control lever to the neutral position.The free accelerator button will return au-tomatically to its set position. The remotecontrol will then engage forward and re-
verse normally.
EMU25911
Tiller handle
To change direction, move the tiller handle tothe left or right as necessary.
EMU25922
Gear shift lever
Pulling the gear shift lever towards you putsthe engine in forward gear so that the boatmoves ahead. Pushing the lever away fromyou puts the engine in reverse gear so thatthe boat moves astern.
1. Fully open2. Fully closed
1. Fully open2. Fully closed3. Free accelerator
1
3
2
ZMU04575
Basic components
16
EMU25941
Throttle grip
The throttle grip is on the tiller handle. Turnthe grip counterclockwise to increase speedand clockwise to decrease speed.
EMU25961
Throttle indicator
The fuel consumption curve on the throttleindicator shows the relative amount of fuelconsumed for each throttle position. Choosethe setting that offers the best performanceand fuel economy for the desired operation.
EMU25971
Throttle friction adjuster
A friction device provides adjustable resis-tance to movement of the throttle grip or theremote control lever, and can be set accord-ing to operator preference.To increase resistance, turn the adjusterclockwise. To decrease resistance, turn theadjuster counterclockwise.
WARNING
EWM00031
Do not overtighten the friction adjuster. Ifthere is too much resistance, it could bedifficult to move the remote control leveror throttle grip, which could result in an
accident.
1. Forward “ ”
2. Neutral “ ”
3. Reverse “ ”
1. Throttle indicator
Basic components
17
When constant speed is desired, tighten theadjuster to maintain the desired throttle set-ting.
EMU25990
Engine stop lanyard switch
The lock plate must be attached to the en-gine stop switch for the engine to run. Thelanyard should be attached to a secure placeon the operator’s clothing, or arm or leg.Should the operator fall overboard or leavethe helm, the lanyard will pull out the lockplate, stopping ignition to the engine. Thiswill prevent the boat from running away un-der power.
WARNING
EWM00120
�
Attach the engine stop switch lanyardto a secure place on your clothing, oryour arm or leg while operating.
�
Do not attach the lanyard to clothingthat could tear loose. Do not route the
lanyard where it could become entan-gled, preventing it from functioning.
�
Avoid accidentally pulling the lanyardduring normal operation. Loss of en-gine power means the loss of moststeering control. Also, without enginepower, the boat could slow rapidly. Thiscould cause people and objects in the
boat to be thrown forward.
NOTE:
The engine cannot be started with the lock
plate removed.
ZMU04646
1. Lanyard2. Lock plate
1. Lanyard2. Lock plate
ONSTARTOFF
ONSTARTOFF
1ZMU04564
2
Basic components
18
EMU26001
Engine stop button
To open the ignition circuit and stop the en-gine, push this button.
EMU26090
Main switch
The main switch controls the ignition system;its operation is described below.
�
“ ”
(off)
With the main switch in the “ ” (off) posi-tion, the electrical circuits are off, and the keycan be removed.
�
“ ”
(on)
With the main switch in the “ ” (on) posi-tion, the electrical circuits are on, and the keycannot be removed.
�
“ ”
(start)
With the main switch in the “ ” (start) po-sition, the starter motor turns to start the en-
gine. When the key is released, it returnsautomatically to the “ ” (on) position.
EMU26111
Steering friction adjuster
A friction device provides adjustable resis-tance to the steering mechanism, and can beset according to operator preference. An ad-juster lever is located on the bottom of thetiller handle bracket.To increase resistance, turn the lever to theport side “A”.
1. Lanyard2. Lock plate
ONOFF START
ONOFF START
ZMU04566
Basic components
19
To decrease resistance, turn the lever to thestarboard side “B”.
WARNING
EWM00040
Do not overtighten the friction adjuster. Ifthere is too much resistance, it could bedifficult to steer, which could result in an
accident.
NOTE:
�
Check the tiller handle for smooth move-ment when the lever is turned to the star-board side “B”.
�
Do not apply lubricants such as grease tothe friction areas of the steering friction ad-
juster.
EMU26141
Power trim and tilt switch on remote control or tiller handle
The power trim and tilt system adjusts theoutboard motor angle in relation to the tran-som. Pressing the switch “ ” (up) trims theoutboard motor up, then tilts it up. Pressingthe switch “ ” (down) tilts the outboard mo-tor down and trims it down. When the switchis released, the outboard motor will stop in itscurrent position.
NOTE:
For instructions on using the power trim and
tilt switch, see pages 48 and 50.
EMU26151
Power trim and tilt switch on bottom engine cowling
The power trim and tilt switch is located onthe side of the bottom engine cowling. Press-ing the switch “ ” (up) trims the outboardmotor up, then tilts it up. Pressing the switch“ ” (down) tilts the outboard motor downand trims it down. When the switch is re-leased, the outboard motor will stop in its
ZMU03591AB
Basic components
20
current position.
WARNING
EWM01030
Use the power trim and tilt switch locatedon the bottom engine cowling only whenthe boat is at a complete stop with the en-gine off. Attempting to use this switchwhile the boat is moving could increasethe risk of falling overboard and coulddistract the operator, increasing the riskof collision with another boat or an obsta-
cle.
NOTE:
For instructions on using the power trim and
tilt switch, see page 50.
EMU26161
Power trim and tilt switches (twin binnacle type)
The power trim and tilt system adjusts theoutboard motor angle in relation to the tran-som. Pushing the switch “ ” (up) trims theoutboard motor up, then tilts it up. Pressingthe switch “ ” (down) tilts the outboard mo-tor down and trims it down. When the switchis released, the outboard motor will stop in itscurrent position.
NOTE:
�
On the dual engine control, the switch onthe remote control grip controls both out-board motors at the same time.
�
For instructions on using the power trim
and tilt switches, see pages 48 and 50.
EMU26241
Trim tab with anode
The trim tab should be adjusted so that thesteering control can be turned to either theright or left by applying the same amount offorce.
WARNING
EWM00840
An improperly adjusted trim tab couldcause difficult steering. Always test runafter the trim tab has been installed or re-placed to be sure steering is correct. Besure you have tightened the bolt after ad-
justing the trim tab.
If the boat tends to veer the left (port side),turn the trim tab rear end to the port side “A”in the figure. If the boat tends to veer the right(starboard side), turn the trim tab end to thestarboard side “B” in the figure.
CAUTION:
ECM00840
The trim tab also serves as an anode to
1. Power trim and tilt switch
UP
DN
ZMU04223
1
1. Power trim and tilt switch
ZMU04601
DN
UP
1
Basic components
21
protect the engine from electrochemicalcorrosion. Never paint the trim tab as it
will become ineffective as an anode.
EMU26340
Tilt support lever for power trim and tilt or hydro tilt model
To keep the outboard motor in the tilted upposition, lock the tilt support lever to theclamp bracket.
EMU26382
Top cowling lock lever (pull up type)
To remove the engine top cowling, pull upthe lock lever(s) and lift off the cowling.When installing the cowling, check to be sureit fits properly in the rubber seal. Then lockthe cowling by moving the lever(s) down-ward.
1. Trim tab2. Bolt3. Cap
1
2
3
ZMU02525
A
B
AB
ZMU01863
1. Tilt support lever
1. Top cowling lock lever(s)
ZMU03979
1
ZMU04225
1
Basic components
22
EMU26460
Flushing device
This device is used to clean the cooling wa-ter passages of the motor using a gardenhose and tap water.
NOTE:
For details on usage, see page 60.
EMU31702
Water separator
This engine has a combination fuel filter/wa-ter separator and associated warning sys-tem. If water separated from the fuelexceeds a specific volume, the warning de-vice will activate.
Activation of warning device
�
The water separator warning indicator willblink.
�
The buzzer will sound intermittently onlywhen the gear shift is in neutral.
�
If the warning system has activated, stopthe engine and consult a Yamaha dealerimmediately.
EMU26470
Tachometer
This gauge shows the engine speed and hasthe following functions.
EMU26491
Digital tachometer
The tachometer shows the engine speedand has the following functions.
NOTE:
All segments of the display will light momen-
1. Top cowling lock lever(s)
1. Flushing device
ZMU04226
1
1
ZMU04256
1. Tachometer2. Warning indicator(s)
ZMU05483
ZMU04578
1
2
Basic components
23
tarily after the main switch is turned on and
will return to normal thereafter.
NOTE:
The water separator and engine troublewarning indicators only operate when the en-gine is equipped with the appropriate func-
tions.
EMU26503
Low oil pressure warning indicator
If oil pressure drops too low, this indicator willflash. For further information, see page 36.
CAUTION:
ECM00020
�
Do not continue to run the engine if thelow oil pressure warning indicator is onand the engine oil level is lower. Seri-ous engine damage will occur.
�
The low oil pressure warning indicatordoes not indicate the engine oil level.Use the oil dipstick to check the re-maining oil quantity. For further infor-
mation, see page 40.
EMU26522
Low oil pressure warning indicator
If oil pressure drops too low, the warning in-dicator will start to blink. For further informa-tion, see page 36.
CAUTION:
ECM00020
�
Do not continue to run the engine if thelow oil pressure warning indicator is onand the engine oil level is lower. Seri-ous engine damage will occur.
�
The low oil pressure warning indicatordoes not indicate the engine oil level.Use the oil dipstick to check the re-maining oil quantity. For further infor-
mation, see page 40.
1. Tachometer2. Trim meter3. Hour meter4. Low oil pressure warning indicator5. Overheat warning indicator6. Water separator warning indicator7. Engine trouble warning indicator8. Set button9. Mode button
1
5
2
4
3
76
8 9 ZMU04185
1. Low oil pressure warning indicator
ZMU04754
ZMU017361
Basic components
24
EMU26572
Overheat warning indicator
If the engine temperature rises too high, thisindicator will flash. For further information onreading the indicator, see page 36.
CAUTION:
ECM00050
Do not continue to run the engine if theoverheat warning indicator is on. Serious
engine damage will occur.
EMU26581
Overheat warning indicator (digital type)
If the engine temperature rises too high, thewarning indicator will start to blink. For fur-ther information on reading the indicator, seepage 36.
CAUTION:
ECM00050
Do not continue to run the engine if theoverheat warning indicator is on. Serious
engine damage will occur.
EMU26600
Speedometer (digital type)
This gauge shows the boat speed.
NOTE:
After the main switch is first turned on, allsegments of the display come on as a test.After a few seconds, the gauge will changeto normal operation. Watch the gauge whenturning on the main switch to make sure all
segments come on.
NOTE:
The speedometer displays km/h, mph, orknots, according to operator preference. Se-lect the desired unit of measurement by set-
ZMU04715
1. Overheat warning indicator
1. Speedometer2. Fuel gauge3. Trip meter/clock/voltmeter4. Warning indicator(s)
ZMU01737
1
Basic components
25
ting the selector switch on the back of the
gauge. See the illustration for settings.
EMU26610
Trim meter
This gauge shows the trim angle of your out-board motor.
NOTE:
Memorize the trim angles that work best foryour boat under different conditions. Adjustthe trim angle to the desired setting with the
power trim and tilt switch.
EMU26620
Trim meter (digital type)
This meter shows the trim angle of your out-board motor.
NOTE:
�
Memorize the trim angles that work bestfor your boat under different conditions.Adjust the trim angle to the desired usingthe power trim and tilt switch.
�
If the trim angle of your motor exceeds thetrim operating range, the top segment on
the trim meter display will blink.
EMU26650
Hour meter (digital type)
This meter shows the number of hours theengine has been run. It can be set to showthe total number of hours or the number ofhours for the current trip. The display canalso be turned on and off.
�
Changing the display format
�
Pressing the “ ” (mode) button chang-es the display format in the following pat-tern:
�
Total hours
→
Trip hours
→
Display off
1. Cap2. Selector switch (for speed unit)3. Selector switch (for fuel sensor)
ZMU04581
ZMU01740
ZMU01741
Basic components
26
�
Resetting the trip hours
�
Simultaneously pressing the “ ” (set)and “ ” (mode) buttons for more than1 second while the trip hours are displayedresets the trip counter to 0 (zero).
NOTE:
The total number of hours the engine has
been run cannot be reset.
EMU26690
Trip meter
This gauge displays the distance the boathas traveled since the gauge was last reset.Press the “ ” (mode) button repeatedlyuntil the indicator on the face of the gaugepoints to “ ” (trip). To reset the trip meterto zero, press the “ ” (set) and “ ”(mode) buttons at the same time.
NOTE:
�
The trip distance is shown in kilometers ormiles depending upon the unit of measure-ment selected for the speedometer.
�
The trip distance is kept in memory by bat-tery power. The stored data will be lost if
the battery is disconnected.
EMU26700
Clock
Press the “ ” (mode) button repeatedlyuntil the indicator on the face of the gaugepoints to “ ” (time). To set the clock, besure the gauge is in the “ ” (time) mode.
Press the “ ” (set) button; the hour displaywill begin blinking. Press the “ ” (mode)button until the desired hour is displayed.Press the “ ” (set) button again, the minutedisplay will begin blinking. Press the “ ”(mode) button until the desired minute is dis-played. Press the “ ” (set) button again tostart the clock.
NOTE:
The clock operates on battery power. Dis-connecting the battery will stop the clock.
Reset the clock after connecting the battery.
EMU26710
Fuel gauge
The fuel level is indicated by eight segments.When all segments are showing, the fueltank is full.
CAUTION:
ECM00860
The Yamaha fuel tank sensor differs fromconventional sensors. Incorrectly settingthe selector switch on the gauge will givefalse readings. Consult your Yamahadealer on how to correctly set the selec-
tor switch.
NOTE:
The fuel level reading can be affected by theposition of the sensor in the fuel tank and theattitude of the boat in the water. Operationwith bow-up trim or continuous turning can
Basic components
27
give false readings.
EMU26720
Fuel warning indicator
If the fuel level decreases to one segment,the fuel level warning segment will begin toblink.
CAUTION:
ECM00880
Do not continue to operate the enginewith full throttle if a warning device hasactivated. Get back to the port within troll-
ing engine speed.
EMU26730
Low battery voltage warning indicator
If battery voltage drops, the display will auto-
matically turn on and begin to blink.
CAUTION:
ECM00870
Get back to the port soon if a warning de-vice has activated. For charging the bat-
tery, consult your Yamaha dealer.
EMU26740
Fuel management meter
The fuel management meter shows the stateof the fuel consumption while the engine isrunning.
NOTE:
After the main switch is first turned on, all
1. Fuel level warning segment
ZMU01745
1. Low battery indicator
1. Fuel flow meter2. Fuel consumption meter / Fuel economy meter / Twin engine speed synchronizer3. Water separator warning indicator (operates only if the sensor has been installed)
ZMU01748
1
23
Basic components
28
segments of the display come on as a test.After a few seconds, the gauge will changeto normal operation. Watch the gauge whenturning on the main switch to make sure all
segments come on.
EMU26750
Fuel flow meter
The fuel flow meter displays the amount offuel flow over a one hour period, at the cur-rent rate of engine operation.If twin engines are installed on your boat, thefuel flow meter displays the total fuel flow ofboth the port and starboard engines. It alsodisplays “ ” (for port and starboard).
Use the “ ” (set) button to rotate the fuelflow display in the following order:
�
Press the “ ” (set) button once to displaythe fuel flow of the starboard engine. An“ ” (for starboard) will also be displayed.
�
Press the “ ” (set) button a second timeto display the fuel flow of the port engine.A “ ” (for port) will also be displayed.
�
Press the “ ” (set) button a third time toreturn the display to the total fuel flow ofboth engines. “ ” (for port and starboard)will also be displayed to indicate both theport and starboard engines.
NOTE:
�
The fuel flow meter displays gallons/houror liters/hour according to operator prefer-ence. Select the desired unit of measure-
ment by setting the selector switch on theback of the gauge during installation.
�
The fuel consumption meter and fueleconomy meter will indicate the same unit
of measurement.
EMU26760
Fuel consumption meter
This gauge displays the total amount of fuelconsumed since the gauge was last reset.Press the “ ” (mode) button repeatedlyuntil the indicator on the face of the gaugepoints to total “ ” (total). To reset the totalfuel consumption to zero, press the “ ”(set) and “ ” (mode) buttons at the sametime.
EMU26770
Fuel economy
This gauge displays the distance per liter orgallon when cruising, and is only for refer-
ZMU01749
1. Selector switch
ZMU01751
Basic components
29
ence use by the operator.Press the “ ” (mode) button repeatedlyuntil the indicator on the face of the gaugepoints to “ ” (economy).
NOTE:
If twin engines are installed on your boat, thegauge will only display the total fuel economy
of both engines.
NOTE:
�
Fuel consumption varies greatly with boatdesign, weight, propeller used, engine trimangle, sea conditions (including wind), andthrottle position. Fuel consumption alsovaries slightly with the type of water (salt,fresh, and contaminate levels), air temper-ature and humidity, cleanliness of the boatbottom, engine mounting height, skill ofthe operator, and individual gasoline for-mulation (winter or summer fuel andamount of additives).
�
The Yamaha digital speedometer and fuelmanagement meter calculates speed,miles traveled, and fuel economy by watermovement at the stern of the boat. Thisdistance can vary greatly from the actualdistance traveled because of water cur-rents, sea swells, and the condition of thewater speed sensor (partially plugged ordamaged).
�
Individual engines may slightly vary in their
fuel consumption due to manufacturingvariations. These variations can be evengreater if the engines are of different yearmodels. In addition, variations in propel-lers, even of the same basic dimensions ofthe same design, can also cause a slight
variation in fuel consumption.
EMU26780
Twin-engine speed synchronizer
This gauge displays the difference in enginespeed (r/min) between the port and star-board engines for reference purposes whensynchronizing the two engines’ speeds.Press the “ ” (mode) button repeatedlyuntil the indicator on the face of the gaugepoints to “ ” (synchronizer).
ZMU01752
1. Port engine speed is higher2. Port engine speed is slightly higher3. Engine speed is synchronized evenly between port and starboard engines4. Starboard engine speed is slightly higher
ZMU01753
ZMU01754
1
2
3
4
5
Basic components
30
NOTE:
If the two engines’ speeds are not synchro-nized while cruising, they can be synchro-
nized by adjusting trim angle or throttle.
EMU31640
Command link multifunction meters
Command link multifunction meters have 6kinds of meter units; tachometer unit (squareor round types), speedometer unit (squaretype), speed & fuel meter unit (square orround types), and fuel management meter(square type). The indicator system is slight-ly different between the round and squaretypes. Check the model and type of your unitcarefully. This manual describes mainly thewarning indicators. For more details on set-ting meters or changing indicator systems,see the attached operation manual.
EMU31680
Tachometer unit
The tachometer shows the engine revolu-tions per minute. It has functions of trimmeter, adjusting trolling speed, cooling wa-ter/engine temperature display, battery volt-age display, total hour/trip hour display, oilpressure display, water detection warning,engine trouble warning, and periodic mainte-nance notification. If optional sensors areconnected to the unit, cooling water pressuredisplay will be available. For the optionalsensor, consult your Yamaha dealer. The ta-chometer unit is available in round or squaretypes. Check your tachometer unit type.
5. Starboard engine speed is higher
1. Set button2. Mode button
1. Tachometer2. Trim meter3. Multifunction display4. Cooling water pressure5. Cooling water/engine temperature6. Water detection warning indicator7. Battery voltage8. Oil pressure (4-stroke models)
21
ZMU05415
2
3
1
4
5
6
7
8 ZMU05416
Basic components
31
NOTE:
The tachometer unit shows various kinds ofinformation according to the setting madeusing the “ ” (set) and “ ” (mode) but-tons. For details, see the attached operation
manual.
Preoperation checks
Place the gear shift lever in neutral and turnthe main switch to “ ” (on). After all the dis-plays come on and the total hour displaycomes on, the gauge will change to normaloperation. If the buzzer sounds and the wa-ter separator warning indicator blinks, con-sult your Yamaha dealer immediately.
NOTE:
To stop the buzzer, press the “ ” (set) or
“ ” (mode) button.
Low oil pressure warning
When the engine oil pressure drops too low,the low oil pressure warning indicator willstart to blink, and the engine speed will auto-matically decrease to about 2000 r/min.
Stop the engine immediately if the buzzersounds and the low oil pressure warning in-dicator blinks. Check the engine oil quantityand replenish oil if necessary. If the warning
1. Set button2. Mode button
1. Tachometer2. Trim meter3. Multifunction display4. Water detection warning indicator5. Engine trouble warning/maintenance indica-tor6. Cooling water pressure7. Oil pressure (4-stroke models)8. Cooling water/engine temperature9. Battery voltage
21
ZMU05417
1 4 5 2
3
6 87 9 ZMU05418
ZMU05430
ZMU05431
Basic components
32
device has activated while the appropriateengine oil quantity is maintained, consultyour Yamaha dealer.
CAUTION:
ECM01600
Do not continue to run the engine if thelow oil pressure warning device has acti-
vated. Serious engine damage will occur.
Overheat warning
If the engine temperature rises too high whilecruising, the overheat warning indicator willstart to blink. The engine speed will automat-ically decrease to about 2000 r/min.
Stop the engine immediately if the buzzersounds and the overheat warning device hasactivated. Check the cooling water inlet forclogging.
CAUTION:
ECM01590
�
Do not continue to run the engine if theoverheat warning indicator blinks. Seri-
ous engine damage will occur.
�
Do not continue to operate the engine ifa warning device has activated. Con-sult your Yamaha dealer if the problem
cannot be located and corrected.
Water separator warning
This indicator will blink when water has accu-mulated in the water separator (fuel filter)while cruising. In such an event, stop the en-gine immediately and see page 78 of thismanual to drain the water from the fuel filter.Get back to the port soon and consult aYamaha dealer immediately.
CAUTION:
ECM00910
Gasoline mixed with water could cause
damage to the engine.
Engine trouble warning
This indicator will blink when the engine mal-functions while cruising. Get back to the port
ZMU05421
ZMU05422
ZMU05423
ZMU05424
Basic components
33
soon and consult a Yamaha dealer immedi-ately.
CAUTION:
ECM00920
In such an event, the engine will not oper-ate properly. Consult a Yamaha dealer
immediately.
Low battery voltage warning
When the battery voltage drops, the low bat-tery voltage warning indicator and the bat-tery voltage value will start to blink. Get backto the port soon if the low battery voltagewarning device has activated. For chargingthe battery, consult your Yamaha dealer.
EMU31610
Speed & fuel meter unit
This unit shows the boat speed and has thefunctions of fuel meter, total fuel consump-tion display, fuel economy display, fuel flowdisplay, and system voltage display. If op-tional sensors are connected to the unit, tripdisplay, water surface temperature display,depth display, and clock will be available. Forthe optional sensor, consult your Yamahadealer. The speed & fuel meter unit is avail-able in round or square types. Check yourspeed & fuel meter unit type.
ZMU05425
ZMU05426
ZMU05427
ZMU05428
Basic components
34
NOTE:
After the main switch is first turned on, all thedisplays come on as a test. After a few sec-onds, the gauge will change to normal oper-
ation.
NOTE:
The speed & fuel meter unit shows variouskinds of information according to the settingmade with the “ ” (set) and “ ” (mode)buttons. For details, see the attached opera-
tion manual.
EMU31620
Speedometer unit
This unit shows the boat speed and hasfunctions of fuel meter and system voltagedisplay. If optional sensors are connected tothe unit, trip display, water surface tempera-ture display, depth display, and clock will beavailable. For the optional sensor, consultyour Yamaha dealer.
1. Set button2. Mode button
1. Speedometer2. Fuel meter3. Multifunction display
1. Set button2. Mode button
21
ZMU05432
1
23
ZMU05433
21
ZMU05434
1. Speedometer2. Fuel meter3. Multifunction display
1 2
3 ZMU05435
Basic components
35
NOTE:
After the main switch is first turned on, all thedisplays come on as a test. After a few sec-onds, the gauge will change to normal oper-
ation.
NOTE:
The speedometer unit shows various kindsof information according to the setting madeusing the “ ” (set) and “ ” (mode) but-tons. In addition, the speedometer can showthe desired unit of measurement such as km/h, mph, or knots. For details, see the at-
tached operation manual.
EMU31630
Fuel management meter
This meter has functions of fuel flow meter,total consumption display, fuel economy dis-play, and remaining fuel display.
NOTE:
After the main switch is first turned on, all thedisplays come on as a test. After a few sec-onds, the gauge will change to normal oper-
ation.
NOTE:
The fuel management meter shows variouskinds of information when the operator usesthe “ ” (set) and “ ” (mode) buttons.For details, see the attached operation man-
1. Set button2. Mode button
1. Speedometer2. Fuel meter3. Multifunction display
21
ZMU05436
1
23
ZMU05437
1. Set button2. Mode button
1. Fuel flow meter2. Multifunction display
21
ZMU05438
1
2
ZMU05439
Basic components
36
ual.
EMU26801
Warning system
CAUTION:
ECM00090
Do not continue to operate the engine if awarning device has activated. Consultyour Yamaha dealer if the problem can-
not be located and corrected.
EMU30341
Overheat warning (twin engines)
This engine has an overheat warning device.If the engine temperature rises too high, thewarning device will activate.Activation of warning device
�
Engine speed will automatically decreaseto 2000–3500 r/min.
�
If equipped with an overheat warning indi-cator, it will light or blink.
�
The buzzer will sound.
If the warning system has activated, stop theengine and check the cooling water inlet forclogging.
NOTE:
Dual engine drive users:Should the overheat warning system of oneengine activate, the engine will slow downand the buzzer will sound. This will cause theother engine to slow down and the buzzer tosound. To switch off the warning activation
ZMU04746
ZMU04227
ZMU03025
OFF START
ON
OFF START
ON
ZMU04584
ZMU02630
Basic components
37
on the engine not affected by overheating,turn off the main switch of the engine over-
heating.
EMU30352
Low oil pressure warning
If the oil pressure drops too low, the warningdevice will activate.Activation of warning device
�
Engine speed will automatically decreaseto 2000–3500 r/min.
�
The low oil pressure warning indicator willlight or blink.
�
The buzzer will sound.
If the warning system has activated, stop theengine as soon as it is safe to do so. Checkthe oil level and add oil as needed. If the oillevel is correct, consult your Yamaha dealer.
CAUTION:
ECM00100
Do not continue to run the engine if thelow oil pressure warning indicator is on.
Serious engine damage could occur.
ZMU04587
ZMU04254
ZMU02360
OFF START
ON
OFF START
ON
ZMU04584
38
Operation
EMU26901
Installation
CAUTION:
ECM00110
Incorrect engine height or obstructionsto smooth water flow (such as the designor condition of the boat, or accessoriessuch as transom ladders or depth findertransducers) can create airborne waterspray while the boat is cruising. Severeengine damage may result if the motor isoperated continuously in the presence of
airborne water spray.
NOTE:
During water testing check the buoyancy ofthe boat, at rest, with its maximum load.Check that the static water level on the ex-haust housing is low enough to prevent wa-ter entry into the powerhead, when waterrises due to waves when the outboard is not
running.
EMU26910
Mounting the outboard motor
WARNING
EWM00820
�
Overpowering a boat could cause se-vere instability. Do not install an out-board motor with more horsepowerthan the maximum rating on the capac-ity plate of the boat. If the boat does nothave a capacity plate, consult the boatmanufacturer.
�
The information presented in this sec-tion is intended as reference only. It isnot possible to provide complete in-structions for every possible boat andmotor combination. Proper mountingdepends in part on experience and the
specific boat and motor combination.
WARNING
EWM00830
Improper mounting of the outboard mo-tor could result in hazardous conditionssuch as poor handling, loss of control, orfire hazards. Observe the following:
�
For permanently mounted models, yourdealer or other person experienced inproper rigging should mount the motor.If you are mounting the motor yourself,you should be trained by an experi-enced person.
�
For portable models, your dealer or oth-er person experienced in proper out-board motor mounting should show
you how to mount your motor.
Mount the outboard motor on the center line(keel line) of the boat, and ensure that theboat itself is well balanced. Otherwise theboat will be hard to steer. For boats withouta keel or which are asymmetrical, consultyour dealer.
1. Center line (keel line)
ZMU017601
Operation
39
EMU26930
Mounting height (boat bottom)
To run your boat at optimum efficiency, thewater resistance (drag) of the boat and out-board motor must be made as little as possi-ble. The mounting height of the outboardmotor greatly affects the water resistance. Ifthe mounting height is too high, cavitationtends to occur, thus reducing the propulsion;and if the propeller tips cut the air, the enginespeed will rise abnormally and cause the en-gine to overheat. If the mounting height is toolow, the water resistance will increase andthereby reduce engine efficiency. Mount theoutboard motor so that the anti-cavitationplate is in alignment with the bottom of theboat.
NOTE:
�
The optimum mounting height of the out-
board motor is affected by the boat/motorcombination and the desired use. Testruns at different heights can help deter-mine the optimum mounting height. Con-sult your Yamaha dealer or boatmanufacturer for further information on de-termining the proper mounting height.
�
For instructions on setting the trim angle of
the outboard motor, see page 48.
EMU30173
Breaking in engine
Your new engine requires a period of break-in to allow mating surfaces of moving parts towear in evenly. Correct break-in will help en-sure proper performance and longer enginelife.
CAUTION:
ECM00800
Failure to follow the break-in procedurecould result in reduced engine life or
even severe engine damage.
EMU27081
Procedure for 4-stroke models
Run the engine under load (in gear with apropeller installed) for 10 hours as follows.1. First hour:
Run the engine at 2000 r/min or at ap-proximately half throttle.
2. Second hour:Run the engine at 3000 r/min or at ap-proximately three-quarter throttle.
3. Remaining eight hours:Run the engine at any speed. However,avoid operating at full throttle for morethan 5 minutes at a time.
4. After the first 10 hours:Operate the engine normally.
1. Center line (keel line)
ZMU01874
Operation
40
EMU27103
Preoperation checks
WARNING
EWM00080
If any item in the preoperation check isnot working properly, have it inspectedand repaired before operating the out-board motor. Otherwise an accident
could occur.
CAUTION:
ECM00120
Do not start the engine out of water. Over-heating and serious engine damage can
occur.
EMU31550
Fuel
�
Check to be sure you have plenty of fuelfor your trip.
�
Make sure there are no fuel leaks or gaso-line fumes.
�
Check fuel line connections to be sure theyare tight (if equipped Yamaha fuel tank orboat tank).
�
Be sure the fuel tank is positioned on a se-cure, flat surface, and that the fuel line isnot twisted or flattened, or likely to contactsharp objects (if equipped Yamaha fueltank or boat tank).
�
Check the water in the fuel filter with thewater separator warning device. Place thegear shift lever in neutral and turn the mainswitch to “ ”(on). If the buzzer soundsand the water separator warning indicatorblinks, consult your Yamaha dealer imme-diately.
EMU27130
Controls
�
Check throttle, shift, and steering for prop-er operation before starting the engine.
�
The controls should work smoothly, with-out binding or unusual free play.
�
Look for loose or damaged connections.
�
Check operation of the starter and stopswitches when the outboard motor is in thewater.
EMU27150
Engine
�
Check the engine and engine mounting.
�
Look for loose or damaged fasteners.
�
Check the propeller for damage.
�
Check that the battery is in good conditionand the battery connections are secure.
EMU27163
Checking the engine oil level
1. Put the outboard motor in an upright po-sition (not tilted).
2. Remove oil dipstick and wipe it clean.3. Completely insert the dipstick and re-
move it again.4. Check the oil level using the dipstick to
be sure the level falls between the upperand lower marks. Fill with oil if it is belowthe lower mark, or drain to the specifiedlevel if it is above the upper mark.
1. Oil dipstick
ZMU04257
1
Operation
41
NOTE:
Be sure to completely insert the dipstick into
the dipstick guide.
EMU30021
Filling fuel
WARNING
EWM00060
Gasoline and its vapors are highly flam-mable and explosive. Keep away fromsparks, cigarettes, flames, or other
sources of ignition.
1. Remove the fuel tank cap.2. Carefully fill the fuel tank.3. Securely close the cap after filling the
tank. Wipe up any spilled fuel.
EMU27270
Ring Free Fuel Additive
Gasoline is a precise blend of many differentsubstances, each chosen to give certaincharacteristics. Gasoline blends have beenchanging in recent years in response to con-cerns about pollution and resulting emis-sions regulations. One of the most obviouschanges has been the elimination of leadfrom most fuels.As gasoline has changed, the amount of ad-
ditives such as aromatics and oxygenateshas increased. These additives are impor-tant for the engines in passenger cars, butthey can have detrimental effects in marineengines, because of increased deposits inthe combustion chamber. When enough de-posits collect, piston rings begin sticking.Performance drops and engine wear in-creases dramatically.While many additives available may reducedeposits, Yamaha recommends the use of
Ring Free Fuel Additive
, available fromyour Yamaha dealer.
Ring Free Fuel Addi-tive
has repeatedly proven its ability to cleancombustion deposits from inside the engine,notably the critical piston-ring-land area, andfuel system components. Follow product la-beling for use instructions.
EMU27450
Operating engine
EMU27482
Feeding fuel
WARNING
EWM00420
�
Before starting the engine, make surethat the boat is tightly moored and thatyou can steer clear of any obstructions.Be sure there are no swimmers in thewater near you.
�
When the air vent screw is loosened,gasoline vapor will be released. Gaso-line is highly flammable, and its vaporsare flammable and explosive. Refrainfrom smoking, and keep away fromopen flames and sparks while loosen-ing the air vent screw.
�
This product emits exhaust gaseswhich contain carbon monoxide, a col-orless, odorless gas which could causebrain damage or death when inhaled.Symptoms include nausea, dizziness,
1. Lower level mark2. Oil dipstick3. Upper level mark
ZMU02082
13
2
Operation
42
and drowsiness. Keep cockpit and cab-in areas well ventilated. Avoid blocking
exhaust outlets.
1. If there is an air vent screw on the fueltank cap, loosen it 2 or 3 turns.
2. If there is a fuel joint or a fuel cock on theboat, firmly connect the fuel line to thejoint or open the fuel cock.
3. Squeeze the primer pump, with the ar-row pointing up, until you feel it becomefirm.
EMU27490
Starting engine
EMU27592
Electric start / prime start models
1. Place the gear shift lever in neutral.
NOTE:
The start-in-gear protection device preventsthe engine from starting except when in neu-
tral.
2. Attach the engine stop switch lanyard toa secure place on your clothing, or yourarm or leg. Then install the lock plate onthe other end of the lanyard into the en-gine stop switch.
WARNING
EWM00120
�
Attach the engine stop switch lanyardto a secure place on your clothing, oryour arm or leg while operating.
�
Do not attach the lanyard to clothingthat could tear loose. Do not route thelanyard where it could become entan-gled, preventing it from functioning.
�
Avoid accidentally pulling the lanyardduring normal operation. Loss of en-gine power means the loss of moststeering control. Also, without enginepower, the boat could slow rapidly. Thiscould cause people and objects in the
boat to be thrown forward.
3. Place the throttle grip in the “ ”(start) position. After the engine starts,return the throttle to the fully closed po-sition.
1. Arrow
Operation
43
4. Turn the main switch to “ ” (start),and hold it for a maximum of 5 seconds.
5. Immediately after the engine starts, re-lease the main switch and allow it to re-turn to “ ” (on).
CAUTION:
ECM00191
�
Never turn the main switch to “ ”(start) while the engine is running.
�
Do not keep the starter motor turningfor more than 5 seconds. If the startermotor is turned continuously for morethan 5 seconds, the battery will bequickly discharged, thus making it im-possible to start the engine. The startercan also be damaged. If the engine willnot start after 5 seconds of cranking,return the main switch to “ ” (on), wait10 seconds, then crank the engine
again.
NOTE:
�
When the engine is cold, it needs to bewarmed up. For further information, seepage 45.
�
If the engine is warm and fails to start,open the throttle slightly and try to start theengine again. If the engine still fails to
start, see page 75.
EMU27624
Electric start and remote control models
1. Place the remote control lever in “ ”(neutral).
NOTE:
The start-in-gear protection device preventsthe engine from starting except when in neu-
tral.
2. Attach the engine stop switch lanyard toa secure place on your clothing, or yourarm or leg. Then install the lock plate onthe other end of the lanyard into the en-
N
ZMU04588
Operation
44
gine stop switch.
WARNING
EWM00120
�
Attach the engine stop switch lanyardto a secure place on your clothing, oryour arm or leg while operating.
�
Do not attach the lanyard to clothingthat could tear loose. Do not route thelanyard where it could become entan-gled, preventing it from functioning.
�
Avoid accidentally pulling the lanyardduring normal operation. Loss of en-gine power means the loss of moststeering control. Also, without enginepower, the boat could slow rapidly. Thiscould cause people and objects in the
boat to be thrown forward.
3. Turn the main switch to “ ” (on).
NOTE:
Dual engine users: When the main switch is
turned on, the buzzer operates for a few sec-onds then stops automatically. The buzzer
also operates if one of the engines stalls.
4. Turn the main switch to “ ” (start),and hold it for a maximum of 5 seconds.
5. Immediately after the engine starts, re-lease the main switch to return it to “ ”(on).
CAUTION:
ECM00191
�
Never turn the main switch to “ ”(start) while the engine is running.
�
Do not keep the starter motor turningfor more than 5 seconds. If the startermotor is turned continuously for morethan 5 seconds, the battery will bequickly discharged, thus making it im-possible to start the engine. The startercan also be damaged. If the engine willnot start after 5 seconds of cranking,
ONSTARTOFF
ONSTARTOFF
ZMU04589
STARTON
ZMU04590
Operation
45
return the main switch to “ ” (on), wait10 seconds, then crank the engine
again.
EMU27670
Warming up engine
EMU27710
Manual start and electric start models
1. After starting the engine, allow it to idlefor 3 minutes to warm up. Failure to doso will shorten engine life.
2. Be sure the low oil pressure warning in-dicator goes off after starting the engine.
3. Check for a steady flow of water from thecooling water pilot hole.
CAUTION:
ECM00210
�
If the low oil pressure warning indicatordoes not go off after the engine starts,stop the engine. Otherwise serious en-gine damage could occur. Check the oillevel and add oil if necessary. Consultyour Yamaha dealer if the cause for thelow oil pressure warning indicator can-not be found.
�
A continuous flow of water from the pi-lot hole shows that the water pump ispumping water through the coolingpassages. If water is not flowing out ofthe pilot hole at all times while the en-gine is running, overheating and seri-ous damage could occur. Stop theengine and check whether the coolingwater inlet on the lower case or thecooling water pilot hole is blocked.Consult your Yamaha dealer if the prob-
lem cannot be located and corrected.
EMU27740
Shifting
WARNING
EWM00180
Before shifting, make sure there are noswimmers or obstacles in the water near
you.
CAUTION:
ECM00220
To change the boat direction or shiftingposition from forward to reverse or vice-versa, first close the throttle so that the
engine idles (or runs at low speeds).
EMU27764
Forward (tiller handle and remote control models)
Tiller handle models1. Place the throttle grip in the fully closed
position.
2. Move the gear shift lever quickly and
ZMU04229
Operation
46
firmly from neutral to forward.
Remote control models1. Pull up the neutral interlock trigger (if
equipped) and move the remote controllever quickly and firmly from neutral toforward.
EMU27785
Reverse (automatic reverse lock and power trim and tilt models)
WARNING
EWM00190
When operating in reverse, go slowly. Donot open the throttle more than half. Oth-erwise the boat could become unstable,which could result in loss of control and
an accident.
Tiller handle models1. Place the throttle grip in the fully closed
position.
2. Move the gear shift lever quickly andfirmly from neutral to reverse.
Remote control models1. Pull up the neutral interlock trigger (if
equipped) and move the remote controllever quickly and firmly from neutral toreverse.
NF
ZMU04597
Operation
47
EMU27820
Stopping engine
Before stopping the engine, first let it cool offfor a few minutes at idle or low speed. Stop-ping the engine immediately after operatingat high speed is not recommended.
EMU27844
Procedure
1. Push and hold the engine stop button orturn the main switch to “ ” (off).
2. After stopping the engine, disconnectthe fuel line if there is a fuel joint on theoutboard motor.
3. Tighten the air vent screw on the fueltank cap (if equipped).
4. Remove the key if the boat will be leftunattended.
NOTE:
The engine can also be stopped by pullingthe lanyard and removing the lock plate fromthe engine stop switch, then turning the main
NR
ZMU04598
OFFON
OFFON
ZMU04600
Operation
48
switch to “ ” (off).
EMU27861
Trimming outboard motor
The trim angle of the outboard motor helpsdetermine the position of the bow of the boatin the water. Correct trim angle will help im-prove performance and fuel economy whilereducing strain on the engine. Correct trimangle depends upon the combination ofboat, engine, and propeller. Correct trim isalso affected by variables such as the load inthe boat, sea conditions, and running speed.
WARNING
EWM00740
Excessive trim for the operating condi-tions (either trim up or trim down) cancause boat instability and can makesteering the boat more difficult. This in-creases the possibility of an accident. Ifthe boat begins to feel unstable or is hardto steer, slow down and/or readjust the
trim angle.
EMU27882
Adjusting trim angle
Power trim and tilt models
WARNING
EWM00751
�
Be sure all people are clear of the out-board motor when adjusting the tilt an-gle, also be careful not to pinch anybody parts between the drive unit andclamp bracket.
�
Use caution when trying a trim positionfor the first time. Increase speed gradu-ally and watch for any signs of instabil-ity or control problems. Improper trimangle can cause loss of control.
�
If equipped with a power trim and tiltswitch located on the bottom cowling,use the switch only when the boat is ata complete stop with the engine off. Donot adjust the trim angle with this
1. Trim operating angle
1ZMU04258
Operation
49
switch while the boat is moving.
Adjust the outboard motor trim angle usingthe power trim and tilt switch.
To raise the bow (trim-out), press the switch“ ” (up).To lower the bow (trim-in), press the switch“ ” (down).Make test runs with the trim set to differentangles to find the position that works best foryour boat and operating conditions.
EMU27911
Adjusting boat trim
When the boat is on plane, a bow-up attituderesults in less drag, greater stability and effi-ciency. This is generally when the keel line ofthe boat is up about 3 to 5 degrees. With thebow up, the boat may have a greater tenden-cy to steer to one side or the other. Compen-sate for this as you steer. The trim tab canalso be adjusted to help offset this effect.When the bow of the boat is down, it is easierto accelerate from a standing start ontoplane.
1. Power trim and tilt switch
1. Power trim and tilt switch
1. Power trim and tilt switch
ZMU04601
DN
UP
1
UP
DN
1
ZMU04231
1. Power trim and tilt switch
Operation
50
Bow Up
Too much trim-out puts the bow of the boattoo high in the water. Performance and econ-omy are decreased because the hull of theboat is pushing the water and there is moreair drag. Excessive trim-out can also causethe propeller to ventilate, which reduces per-formance further, and the boat may “por-poise” (hop in the water), which could throwthe operator and passengers overboard.
Bow Down
Too much trim-in causes the boat to “plow”through the water, decreasing fuel economyand making it hard to increase speed. Oper-ating with excessive trim-in at higher speedsalso makes the boat unstable. Resistance atthe bow is greatly increased, heightening thedanger of “bow steering” and making opera-tion difficult and dangerous.
NOTE:
Depending on the type of boat, the outboardmotor trim angle may have little effect on the
trim of the boat when operating.
EMU27933
Tilting up and down
If the engine will be stopped for some time orif the boat is moored in shallows, the out-board motor should be tilted up to protect thepropeller and casing from damage by colli-sion with obstructions, and also to reducesalt corrosion.
WARNING
EWM00220
Be sure all people are clear of the out-board motor when tilting up and down,also be careful not to pinch any bodyparts between the drive unit and engine
bracket.
WARNING
EWM00250
Leaking fuel is a fire hazard. If there is afuel joint on the outboard motor, discon-nect the fuel line or close the fuel cock ifthe engine will be tilted for more than a
few minutes. Otherwise fuel may leak.
CAUTION:
ECM00241
�
Before tilting the outboard motor, stopthe engine by following the procedure
Operation
51
on page 47. Never tilt the outboard mo-tor while the engine is running. Severedamage from overheating can result.
�
Do not tilt up the engine by pushing thetiller handle (if equipped) because this
could break the handle.
EMU28007
Procedure for tilting up (power trim and tilt models / power tilt models)
1. Place the remote control lever / gearshift lever in neutral.
2. Disconnect the fuel line from the out-board motor or close the fuel cock.
3. Press the power trim and tilt switch /power tilt switch “ ” (up) until the out-board motor has tilted up completely.
N
ZMU03196
N
ZMU04588
ZMU04602
UP
UP
ZMU04232
Operation
52
4. Push the tilt support knob into the clampbracket or pull the tilt support lever to-ward you to support the engine.
WARNING
EWM00260
After tilting the outboard motor, be sureto support it with the tilt support knob ortilt support lever. Otherwise the outboardmotor could fall back down suddenly if oilin the power trim and tilt unit loses pres-
sure.
5. Models equipped with trim rods: Oncethe outboard motor is supported with thetilt support lever, press the power trimand tilt switch / power tilt switch “ ”(down) to retract the trim rods.
CAUTION:
ECM00250
Be sure to retract the trim rods complete-ly during mooring. This protects the rods
from marine growth and corrosion whichcould damage the power trim and tilt
mechanism.
EMU28055
Procedure for tilting down (power trim and tilt models / power tilt models)
1. Push the power trim and tilt switch / pow-er tilt switch “ ” (up) until the outboardmotor is supported by the tilt rod and thetilt support lever / tilt support knob be-comes free.
2. Release the tilt support lever or pull outthe tilt support knob.
3. Push the power trim and tilt switch / pow-er tilt switch “ ” (down) to lower the out-board motor to the desired position.
ZMU03449
ZMU03452
ZMU03453
Operation
53
EMU28060
Cruising in shallow water
The outboard motor can be tilted up partiallyto allow operation in shallow water.
EMU28090
Power trim and tilt models / power tilt models
The outboard motor can be tilted up partiallyto allow operation in shallow water.
WARNING
EWM00660
�
Place the gear shift in neutral beforesetting up for shallow water cruising.
�
Return the outboard motor to its normalposition as soon as the boat is back in
deeper water.
CAUTION:
ECM00260
Do not tilt the outboard motor up so thatthe cooling water inlet on the lower unit isabove the surface of the water when set-ting up for and cruising in shallow water.Otherwise severe damage from overheat-
ing can result.
EMU28185
Procedure for power trim and tilt / powertilt models
1. Place the remote control lever / gearshift lever in neutral.
DN
ZMU01936
UP
DN
ZMU04603
DN
DN
ZMU04255
N
ZMU03525
Operation
54
2. Slightly tilt the outboard motor up to thedesired position using the power trimand tilt switch / power tilt switch.
3. To return the outboard motor to the nor-mal running position, press the powertrim and tilt switch / power tilt switch andslowly tilt the outboard motor down.
EMU28192
Cruising in other conditions
Cruising in salt water
After operating in salt water, flush the coolingwater passages with fresh water to preventthem from becoming clogged with salt de-posits.
N
ZMU04588
UP
ZMU01935
UP
DN
ZMU04602
UP
UP
ZMU04235
Operation
55
NOTE:
For cooling system flushing instructions, see
page 57.
Cruising in turbid water
Yamaha strongly recommends that you usethe optional chromium-plated water pump kit(not available for some models) if you usethe outboard motor in turbid or muddy waterconditions.
56
Maintenance
EMU31480
SpecificationsNOTE:
“(AL)” stated in the specification data belowrepresents the numerical value for the alumi-num propeller installed.Likewise, “(SUS)” represents the value forstainless steel propeller installed and “(PL)”
for plastic propeller installed.
EMU28218
Dimension:
Overall length: 825 mm (32.5 in)
Overall width: 498 mm (19.6 in)
Overall height L: F115TR 1609 mm (63.3 in)
Overall height X: 1736 mm (68.3 in)
Transom height L: F115TR 516 mm (20.3 in)
Transom height X: 643 mm (25.3 in)
Weight (without propeller) L: F115TR 183.0 kg (403 lb)
Weight (without propeller) X: 188.0 kg (414 lb)
Performance:
Full throttle operating range: 5000–6000 r/min
Maximum output: 84.6 kW@5500 r/min (115 HP@5500 r/min)
Idling speed (in neutral): 750
±
50 r/min
Engine:
Type: 4-stroke L
Displacement: 1741.0 cm
3
(106.24 cu.in)
Bore
×
stroke: 79.0
×
88.8 mm (3.11
×
3.50 in)Ignition system:
TCISpark plug (NGK):
LFR6A-11Spark plug gap:
1.0–1.1 mm (0.039–0.043 in)Control system:
Remote controlStarting system:
ElectricStarting carburetion system:
Electronic fuel injectionValve clearance (cold engine) IN:
0.17–0.23 mm (0.0067–0.0091 in)Valve clearance (cold engine) EX:
0.31–0.37 mm (0.0122–0.0146 in)Min. cold cranking amps (CCA/SAE):
380.0 AMin. marine cranking amps (MCA/ABYC):
502.0 AMin. reserve capacity (RC/SAE):
124 minutesAlternator output for battery DC:
25.0 A
Drive unit:
Gear positions: Forward-neutral-reverse
Gear ratio: 2.15 (28/13)
Trim and tilt system: Power trim and tilt
Propeller mark: F115TR KLF115TR KL
Fuel and oil:
Recommended fuel: Regular unleaded gasoline
Min. pump octane: 86
Maintenance
57
Recommended engine oil: 4-stroke outboard motor oil
Engine oil grade API: API SE, SF, SG, SH, SJ, SL
Engine oil type SAE: SAE10W30 or SAE10W40
Lubrication: Wet sump
Engine oil quantity (excluding oil filter): 4.3 L (4.55 US qt) (3.78 Imp.qt)
Recommended gear oil: Hypoid gear oil SAE#90
Gear oil quantity: F115TR 760.0 cm
3
(25.70 US oz) (26.81 Imp.oz)LF115TR 715.0 cm
3
(24.17 US oz) (25.22 Imp.oz)
Tightening torque for engine:
Spark plug: 25.0 Nm (18.4 ft-lb) (2.55 kgf-m)
Propeller nut: 55.0 Nm (40.6 ft-lb) (5.61 kgf-m)
Engine oil drain bolt: 28.0 Nm (20.7 ft-lb) (2.86 kgf-m)
Engine oil filter: 18.0 Nm (13.3 ft-lb) (1.84 kgf-m)
EMU28222
Transporting and storing outboard motor
WARNING
EWM00690
�
Leaking fuel is a fire hazard. Whentransporting and storing the outboardmotor, close the air vent screw and fuelcock to prevent fuel from leaking.
�
USE CARE when transporting fuel tank,whether in a boat or car.
�
DO NOT fill fuel container to maximumcapacity. Gasoline will expand consid-erably as it warms up and can build uppressure in the fuel container. This can
cause fuel leakage and a potential fire
hazard.
WARNING
EWM00700
Never get under the lower unit while it istilted, even if a motor support bar is used.Severe injury could occur if the outboard
motor accidentally falls.
CAUTION:
ECM00660
Do not use the tilt support lever or knobwhen trailering the boat. The outboardmotor could shake loose from the tilt sup-port and fall. If the motor cannot be trail-ered in the normal running position, usean additional support device to secure it
in the tilt position.
The outboard motor should be trailered andstored in the normal running position. If thereis insufficient road clearance in this position,then trailer the outboard motor in the tilt po-sition using a motor support device such asa transom saver bar. Consult your Yamahadealer for further details.
EMU28280
Storing outboard motor
When storing your Yamaha outboard motorfor prolonged periods of time (2 months orlonger), several important procedures mustbe performed to prevent excessive damage.
ZMU03659
Maintenance
58
It is advisable to have your outboard motorserviced by an authorized Yamaha dealerprior to storage. However, you, the owner,with a minimum of tools, can perform the fol-lowing procedures.
CAUTION:
ECM01080
�
To prevent problems which can becaused by oil entering the cylinder fromthe sump, keep the outboard motor inthe attitude shown when transportingand storing it. If storing or transportingthe outboard motor on its side (not up-right), put it on a cushion after drainingthe engine oil.
�
Do not place the outboard motor on itsside before the cooling water hasdrained from it completely, otherwisewater may enter the cylinder throughthe exhaust port and cause engine trou-ble.
�
Store the outboard motor in a dry, well-
ventilated place, not in direct sunlight.
EMU28303
Procedure
EMU28380
Flushing with the flushing attachment
1. Wash the outboard motor body usingfresh water. For further information, seepage 61.
2. Fill the fuel tank with fresh fuel and addone ounce of “Yamaha Fuel Conditionerand Stabilizer” (Part No. LUB-FUELC-12-00) to each gallon of fuel.
NOTE:
The use of “Yamaha Fuel Conditioner andStabilizer” eliminates the need to drain thefuel system. Consult your Yamaha dealer orother qualified mechanic if the fuel system is
to be drained instead.
3. Remove the top cowling and silencer
cover/cap. Remove the propeller.4. Install the flushing attachment over the
cooling water inlet.
CAUTION:
ECM00300
Do not run the engine without supplyingit with cooling water. Either the enginewater pump will be damaged or the en-gine will be damaged from overheating.Before starting the engine, be sure tosupply water to the cooling water passag-
es.
CAUTION:
ECM00310
Avoid running the outboard motor at highspeed while on the flushing attachment,
otherwise overheating could occur.
5. Cooling system flushing is essential toprevent the cooling system from clog-ging up with salt, sand, or dirt. In addi-tion, fogging/lubricating of the engine ismandatory to prevent excessive enginedamage due to rust. Perform the flush-ing and fogging at the same time.
WARNING
EWM00090
�
Do not touch or remove electrical parts
1. Flushing attachment
Maintenance
59
when starting or during operation.
�
Keep hands, hair, and clothes awayfrom the flywheel and other rotating
parts while the engine is running.
6. Run the engine at a fast idle for 10–15minutes in neutral position while supply-ing fresh water.
7. Just prior to turning off the engine, quick-ly spray “Yamaha Stor-Rite EngineFogging Oil” (Part No. LUB-STRRT-12-00) alternately into each carburetor/each intake manifold. When properlydone, the engine will smoke excessivelyand almost stall.
8. Remove the flushing attachment andwipe off any excess water.
9. Install the silencer cover/cap and topcowling. Install the propeller.
NOTE:
A flushing attachment is available from your
Yamaha dealer.
EMU28401
Lubrication
1. Grease the spark plug threads and in-stall the spark plug(s) and torque toproper specification. For information onspark plug installation, see page 64.
2. Change the gear oil. For instructions,see page 71. Inspect the oil for the pres-ence of water that indicates a leaky seal.Seal replacement should be performedby an authorized Yamaha dealer prior touse.
3. Grease all grease fittings. For further de-tails, see page 64.
EMU30261
Cleaning and anticorrosion measures
1. Wash down the exterior of the outboardmotor with fresh water and dry off com-
pletely.2. Spray the outboard motor exterior with
“Yamaha Silicone Protectant” (Part No.LUB-SILCNE-13-00).
CAUTION:
ECM01401
Do not spray when the engine is running.Also, do not spray near the silencer orinto the engine. Otherwise the engine
could be damaged.
3. Wax the cowling with a non-abrasivewax such as “Yamaha Silicone Wax”(Part No. ACC-11000-15-02).
EMU28430
Battery care
WARNING
EWM00330
Battery electrolytic fluid is dangerous; itcontains sulfuric acid and therefore ispoisonous and highly caustic.Always follow these preventive mea-sures:
�
Avoid bodily contact with electrolyticfluid as it can cause severe burns orpermanent eye injury.
�
Wear protective eye gear when han-dling or working near batteries.
Antidote (EXTERNAL):
�
SKIN - Flush with water.
�
EYES - Flush with water for 15 minutesand get immediate medical attention.
Antidote (INTERNAL):
�
Drink large quantities of water or milkfollowed by milk of magnesia, beatenegg, or vegetable oil. Get immediatemedical attention.
Batteries also generate explosive hydro-gen gas; therefore, you should alwaysfollow these preventive measures:
�
Charge batteries in a well-ventilated ar-
Maintenance
60
ea.
�
Keep batteries away from fire, sparks,or open flames (for example: weldingequipment, lighted cigarettes, and soon.)
�
DO NOT SMOKE when charging or han-dling batteries.
KEEP BATTERIES AND ELECTROLYTIC
FLUID OUT OF REACH OF CHILDREN.
Batteries vary among manufacturers. There-fore the following procedures may not al-ways apply. Consult your batterymanufacturer’s instructions.Procedure1. Disconnect and remove the battery from
the boat. Always disconnect the blacknegative cable first to prevent the risk ofshorting.
2. Clean the battery casing and terminals.Fill each cell to the upper level with dis-tilled water.
3. Store the battery on a level surface in acool, dry, well-ventilated place out of di-rect sunlight.
4. Once a month, check the specific gravityof the electrolyte and recharge as re-quired to prolong battery life.
EMU28442
Flushing power unit
Perform this procedure right after operationfor the most thorough flushing.
CAUTION:
ECM01530
Do not perform this procedure while theengine is running. The water pump maybe damaged and severe damage from
overheating can result.
1. After shutting off the engine, unscrewthe garden hose connector from the fit-ting on the bottom cowling.
2. Screw the garden hose adapter onto agarden hose, which is connected to afresh water supply, and then connect itto the garden hose connector.
3. With the engine off, turn on the water tapand let the water flush through the cool-ing passages for about 15 minutes. Turnoff the water and disconnect the gardenhose adapter from the garden hose con-nector.
4. Reinstall the garden hose connectoronto the fitting on the bottom cowling.Tighten the connector securely.
CAUTION:
ECM00540
Do not leave the garden hose connectorloose on the bottom cowling fitting or letthe hose hang free during normal opera-
1. Fitting2. Garden hose connector3. Garden hose adapter
1
23
ZMU04264
Maintenance
61
tion. Water will leak out of the connectorinstead of cooling the engine, which cancause serious overheating. Be sure theconnector is tightened securely on the fit-
ting after flushing the engine.
NOTE:
�
When flushing the engine with the boat inthe water, tilting up the outboard motor un-til it is completely out of the water willachieve better results.
�
For cooling system flushing instructions,
see page 57.
EMU28450
Cleaning the outboard motor
After use, wash the exterior of the outboardmotor with fresh water. Flush the coolingsystem with fresh water.
NOTE:
For cooling system flushing instructions, see
page 57.
EMU28460
Checking painted surface of motor
Check the motor for scratches, nicks, or flak-ing paint. Areas with damaged paint aremore likely to corrode. If necessary, cleanand paint the areas. A touch-up paint is avail-able from your Yamaha dealer.
EMU28486
Periodic maintenance
WARNING
EWM01070
Be sure to turn off the engine when youperform maintenance unless otherwisespecified. If you or the owner is not famil-iar with machine servicing, this workshould be done by your Yamaha dealer or
other qualified mechanic.
Maintenance, replacement, or repair ofthe emission control devices and sys-tems may be performed by any marineengine repair establishment or individual.All warranty repairs, however, includingthose to the emission control system,must be performed by an authorizedYamaha marine dealership.
A service manual is available for purchasethrough your Yamaha dealer for owners whohave the mechanical skills, tools, and otherequipment necessary to perform mainte-nance not covered by this owner’s manual.
EMU28510
Replacement parts
If replacement parts are necessary, use onlygenuine Yamaha parts or parts of the sametype and of equivalent strength and materi-als. Any part of inferior quality may malfunc-tion, and the resulting loss of control couldendanger the operator and passengers.Yamaha genuine parts and accessories areavailable from your Yamaha dealer.
ZMU04265
Maintenance
62
EMU30563
Maintenance chartNOTE:
�
Refer to the sections in this chapter for explanations of each owner-specific action.
�
The maintenance cycle on these charts assume usage of 200 hours per year and regularflushing of the cooling water passages. Maintenance frequency should be adjusted whenoperating the engine under adverse conditions such as extended trolling.
�
Disassembly or repairs may be necessary depending on the outcome of maintenancechecks.
�
Expendable or consumable parts and lubricants will lose their effectiveness over time andthrough normal usage regardless of the warranty period.
�
When operating in salt water, turbid or muddy water, the engine should be flushed with
clean water after each use.
The “ ” symbol indicates the check-ups which you may carry out yourself.The “ ” symbol indicates work to be carried out by your Yamaha dealer.
Item Actions
Initial Every
10 hours (1 month)
50 hours (3
months)
100 hours (6 months)
200 hours (1
year)
Anode(s) (external)Inspection / replace-ment
Anode(s) (cylinder head, thermostat cover)
Inspection / replace-ment
Battery Inspection / charging
Cooling water pas-sages
Cleaning
Cowling clamp Inspection
Fuel filter (can be dis-assembled)
Inspection / replace-ment
Fuel system Inspection
Gear oil Change
Greasing points Greasing
Idling speed Inspection
PCV (Pressure Con-trol Valve)
Inspection
Power trim and tilt unit Inspection
Propeller and cotter pinInspection / replace-ment
Shift link / shift cable Inspection / adjustment
Maintenance
63
EMU28874
Maintenance chart (additional)
EMU28910
NOTE:
When using lead or high-sulfur gasoline, inspecting valve clearance may be required more
frequently than every 500 hours.
ThermostatInspection / replace-ment
Throttle link / throttle cable / throttle pick-up timing
Inspection / adjustment
Water pumpInspection / replace-ment
Engine oil Inspection / change
Oil filter (cartridge) Change
Spark plug(s)Cleaning / adjustment / replacement
Timing beltInspection / replace-ment
Item ActionsEvery
500 hours (2.5 years) 1000 hours (5 years)
Timing belt Replacement
Valve clearance (DOHC)
Inspection / adjustment
Fuel filter (vapor sepa-rator tank)
Replacement
Anode(s) (exhaust cover, cover joint)
Replacement
Exhaust guide, exhaust manifold
Inspection / replace-ment
Item Actions
Initial Every
10 hours (1 month)
50 hours (3
months)
100 hours (6 months)
200 hours (1
year)
Maintenance
64
EMU28931
Greasing
Yamaha marine grease (Water resistant grease)
F115, LF115
EMU28952
Cleaning and adjusting spark plug
WARNING
EWM00560
When removing or installing a spark plug,be careful not to damage the insulator. Adamaged insulator could allow externalsparks, which could lead to explosion or
fire.
The spark plug is an important engine com-ponent and is easy to inspect. The conditionof the spark plug can indicate somethingabout the condition of the engine. For exam-ple, if the center electrode porcelain is verywhite, this could indicate an intake air leak orcarburetion problem in that cylinder. Do not
attempt to diagnose any problems yourself.Instead, take the outboard motor to aYamaha dealer. You should periodically re-move and inspect the spark plug becauseheat and deposits will cause the spark plugto slowly break down and erode. If electrodeerosion becomes excessive, or if carbon andother deposits are excessive, you should re-place the spark plug with another of the cor-rect type.
Before fitting the spark plug, measure theelectrode gap with a wire thickness gauge;adjust the gap to specification if necessary.
ZMU04266
Standard spark plug:LFR6A-11
Maintenance
65
When fitting the plug, always clean the gas-ket surface and use a new gasket. Wipe offany dirt from the threads and screw in thespark plug to the correct torque.
NOTE:
If a torque-wrench is not available when youare fitting a spark plug, a good estimate ofthe correct torque is 1/4 to 1/2 a turn past fin-ger-tight. Have the spark plug adjusted to thecorrect torque as soon as possible with a
torque-wrench.
EMU28962
Checking fuel system
WARNING
EWM00060
Gasoline and its vapors are highly flam-mable and explosive. Keep away fromsparks, cigarettes, flames, or other
sources of ignition.
WARNING
EWM00910
Leaking fuel can result in fire or explo-sion.
�
Check for fuel leakage regularly.
�
If any fuel leakage is found, the fuelsystem must be repaired by a qualifiedmechanic. Improper repairs can make
the outboard unsafe to operate.
Check the fuel lines for leaks, crack, or mal-function. If a problem is found, your Yamahadealer or other qualified mechanic should re-pair it immediately.
Checkpoints
�
Fuel system parts leakage
�
Fuel line joint leakage
�
Fuel line cracks or other damage
�
Fuel connector leakage
1. Spark plug gap2. Spark plug I.D. mark (NGK)3. Spark plug part number
Spark plug gap:1.0–1.1 mm (0.039–0.043 in)
Spark plug torque:25.0 Nm (18.4 ft-lb) (2.55 kgf-m)
ZMU04267
Maintenance
66
EMU29041
Inspecting idling speed
WARNING
EWM00451
�
Do not touch or remove electrical partswhen starting or during operation.
�
Keep hands, hair, and clothes awayfrom the flywheel and other rotating
parts while the engine is running.
CAUTION:
ECM00490
This procedure must be performed whilethe outboard motor is in the water. Aflushing attachment or test tank can be
used.
A diagnostic tachometer should be used forthis procedure. Results may vary dependingon whether testing is conducted with theflushing attachment, in a test tank, or with theoutboard motor in the water.1. Start the engine and allow it to warm up
fully in neutral until it is running smooth-ly.
NOTE:
Correct idling speed inspection is only possi-ble if the engine is fully warmed up. If notwarmed up fully, the idle speed will measurehigher than normal. If you have difficulty ver-ifying the idle speed, or the idle speed re-quires adjustment, consult a Yamaha dealer
or other qualified mechanic.
2. Verify whether the idle speed is set tospecification. For idle speed specifica-tions, see page 56.
EMU29073
Changing engine oil
WARNING
EWM00760
�
Avoid draining the engine oil immedi-ately after stopping the engine. The oil
is hot and should be handled with careto avoid burns.
�
Be sure the outboard motor is securelyfastened to the transom or a stable
stand.
CAUTION:
ECM00970
�
Do not overfill the oil, and be sure theoutboard motor is upright (not tilted)when checking and changing the en-gine oil.
�
If the oil level is above the upper levelmark, drain until the level meets thespecified capacity. Overfilling the oil
could cause leakage or damage.
CAUTION:
ECM01240
Change the engine oil after the first 10hours of operation, and every 100 hoursor at 6-month intervals thereafter. Other-
wise the engine will wear quickly.
NOTE:
Change the engine oil when the oil is still
warm.
1. Put the outboard motor in an upright po-sition (not tilted).
2. Prepare a suitable container that holds alarger amount than the engine oil capac-ity. Loosen and remove the drain screw
ZMU04270
Maintenance
67
while holding the container under thedrain hole. Then remove the oil filler cap.Let the oil drain completely. Wipe up anyspilled oil immediately.
3. Put a new gasket on the oil drain screw.Apply a light coat of oil to the gasket andinstall the drain screw.
NOTE:
If a torque wrench is not available when youare installing the drain screw, finger tightenthe screw just until the gasket comes intocontact with the surface of the drain hole.Then tighten 1/4 to 1/2 turn more. Tightenthe drain screw to the correct torque with a
torque wrench as soon as possible.
4. Add the correct amount of oil through thefiller hole. Install the filler cap.
5. Start the engine and watch to make surethe low oil pressure warning indicator (ifequipped) turns off. Make sure thatthere are no oil leaks.
CAUTION:
ECM00680
If the low oil pressure warning indicatordoes not turn off or if there are oil leaks,stop the engine and find the cause. Con-tinued operation with a problem couldcause severe engine damage. Consultyour Yamaha dealer if the problem can-
not be located and corrected.
6. Turn off the engine and wait 3 minutes.Recheck the oil level using the dipstickto be sure the level falls between the up-per and lower marks. Fill with oil if it isbelow the lower mark, or drain to thespecified level if it is above the uppermark.
1. Drain screw
Drain screw tightening torque:28.0 Nm (20.7 ft-lb) (2.86 kgf-m)
Recommended engine oil:4-stroke outboard motor oil
Engine oil quantity (excluding oil filter):4.3 L (4.55 US qt) (3.78 Imp.qt)
1
ZMU04241
1. Oil filler cap
1
ZMU04271
Maintenance
68
7. Dispose of used oil according to localregulations.
NOTE:
�
For more information on the disposal ofused oil, consult your Yamaha dealer.
�
Change the oil more often when operatingthe engine under adverse conditions such
as extended trolling.
EMU29112
Checking wiring and connectors
�
Check that each grounding wire is properlysecured.
�
Check that each connector is engaged se-curely.
EMU29120
Exhaust leakage
Start the engine and check that no exhaustleaks from the joints between the exhaustcover, cylinder head, and body cylinder.
EMU29130
Water leakage
Start the engine and check that no waterleaks from the joints between the exhaustcover, cylinder head, and body cylinder.
EMU29140
Engine oil leakage
Check for oil leaks on the around the engine.
NOTE:
If any leaks are found, consult your Yamaha
dealer.
EMU29153
Checking power trim and tilt system
WARNING
EWM00430
�
Never get under the lower unit while itis tilted, even when the tilt support leveris locked. Severe injury could occur ifthe outboard motor accidentally falls.
�
Make sure no one is under the outboard
motor before performing this test.
1. Check the power trim and tilt unit for anysign of oil leaks.
2. Operate each of the power trim and tiltswitches on the remote control and en-gine bottom cowling (if equipped) tocheck that all switches work.
3. Tilt the outboard motor up and checkthat the tilt rod and trim rods are extend-ed completely.
ZMU02058
ZMU04286
1. Tilt rod
ZMU02633
1
2
3
Maintenance
69
4. Use the tilt support lever to lock the mo-tor in the up position. Operate the tiltdown switch briefly so the motor is sup-ported by the tilt support lever.
5. Check that the tilt rod and trim rods arefree of corrosion or other flaws.
6. Activate the tilt-down switch until the trimrods have retracted completely into thecylinders.
7. Activate the trim-up switch until the tiltrod is fully extended. Unlock the tilt sup-port lever.
8. Tilt the outboard motor down. Checkthat the tilt rod and trim rods operatesmoothly.
NOTE:
Consult your Yamaha dealer if any operation
is abnormal.
EMU29171
Checking propeller
WARNING
EWM00321
You could be seriously injured if the en-gine accidentally starts when you arenear the propeller.
�
Before inspecting, removing, or install-ing the propeller, remove the sparkplug caps from the spark plugs. Also,place the shift control in neutral, turnthe main switch to “ ” (off) and re-move the key, and remove the lanyardfrom the engine stop switch. Turn offthe battery cut-off switch if your boathas one.
�
Do not use your hand to hold the pro-peller when loosening or tightening thepropeller nut. Put a wood block be-tween the anti-cavitation plate and thepropeller to prevent the propeller from
turning.
2. Trim rods3. Tilt support lever
1. Tilt support lever
ZMU02634
1
ZMU02635
ZMU04262
Maintenance
70
Checkpoints
�
Check each of the propeller blades forwear, erosion from cavitation or ventila-tion, or other damage.
�
Check the propeller shaft for damage.
�
Check the splines / shear pin for wear ordamage.
�
Check for fish line tangled around the pro-peller shaft.
�
Check the propeller shaft oil seal for dam-age.
NOTE:
If the shear pin equipped: it is designed tobreak if the propeller hits a hard underwaterobstacle to help protect the propeller anddrive mechanism. The propeller will thenspin freely on the shaft. If this happens, the
shear pin must be replaced.
EMU30660
Removing the propeller
EMU29194
Spline models
1. Straighten the cotter pin and pull it outusing a pair of pliers.
2. Remove the propeller nut, washer, andspacer (if equipped).
3. Remove the propeller and thrust wash-er.
EMU30670
Installing the Propeller
EMU29242
Spline models
WARNING
EWM00770
On counter rotation models, be sure touse a propeller intended for counter-clockwise rotation. These propellers areidentified with the letter “L” after the sizeindication on the propeller. Otherwise theboat could move in the opposite direction
ZMU01897
1. Cotter pin2. Propeller nut3. Washer4. Spacer5. Propeller6. Thrust washer
Maintenance
71
from that expected.
CAUTION:
ECM00340
�
Be sure to install the thrust washer be-fore installing the propeller, otherwisethe lower case and propeller bosscould be damaged.
�
Be sure to use a new cotter pin andbend the ends over securely. Otherwisethe propeller could come off during op-
eration and be lost.
1. Apply Yamaha marine grease or a cor-rosion resistant grease to the propellershaft.
2. Install the thrust washer and propelleron the propeller shaft.
3. Install the spacer and washer. Tightenthe propeller nut to the specified torque.
4. Align the propeller nut with the propellershaft hole. Insert a new cotter pin in thehole and bend the cotter pin ends.
NOTE:
If the propeller nut does not align with thepropeller shaft hole after tightening to thespecified torque, tighten the nut further to
align it with the hole.
EMU29282
Changing gear oil
WARNING
EWM00800
�
Be sure the outboard motor is securelyfastened to the transom or a stablestand. You could be severely injured ifthe outboard motor falls on you.
�
Never get under the lower unit while itis tilted, even when the tilt support leveror knob is locked. Severe injury couldoccur if the outboard motor accidental-
ly falls.
1. Tilt the outboard motor so that the gearoil drain screw is at the lowest point pos-sible.
2. Place a suitable container under thegear case.
3. Remove the gear oil drain screw andgasket.
NOTE:
�
If a magnetic gear oil drain screw isequipped, remove all metal particles fromthe screw before installing it.
�
Always use new gaskets. Do not reuse the
removed gaskets.
4. Remove the oil level plug and gasket to
Propeller nut tightening torque:55.0 Nm (40.6 ft-lb) (5.61 kgf-m)
1. Gear oil drain screw2. Oil level plug
ZMU03273
2
1
Maintenance
72
allow the oil to drain completely.
CAUTION:
ECM00710
Inspect the used oil after it has beendrained. If the oil is milky, water is gettinginto the gear case which can cause geardamage. Consult a Yamaha dealer for re-
pair of the lower unit seals.
NOTE:
For disposal of used oil, consult your
Yamaha dealer.
5. With the outboard motor in a vertical po-sition, and using a flexible or pressur-ized filling device, inject the gear oil intothe gear oil drain screw hole.
6. Put a new gasket on the oil level plug.When the oil begins to flow out of the oillevel plug hole, insert and tighten the oillevel plug.
7. Put a new gasket on the gear oil drainscrew. Insert and tighten the gear oil
drain screw.
EMU29312
Inspecting and replacing anode(s)
Yamaha outboard motors are protected fromcorrosion by sacrificial anodes. Inspect theexternal anodes periodically. Remove scalesfrom the surfaces of the anodes. Consult aYamaha dealer for replacement of externalanodes.
CAUTION:
ECM00720
Do not paint anodes, as this would render
them ineffective.
NOTE:
Inspect ground leads attached to externalanodes on equipped models. Consult aYamaha dealer for inspection and replace-ment of internal anodes attached to the pow-
er unit.
Recommended gear oil:Hypoid gear oil SAE#90
Gear oil quantity:F115TR 760.0 cm
3
(25.70 US oz) (26.81 Imp.oz)LF115TR 715.0 cm
3
(24.17 US oz) (25.22 Imp.oz)
ZMU03274
ZMU01901
ZMU04008
Maintenance
73
EMU29320
Checking battery (for electric start models)
WARNING
EWM00330
Battery electrolytic fluid is dangerous; itcontains sulfuric acid and therefore ispoisonous and highly caustic.Always follow these preventive mea-sures:
�
Avoid bodily contact with electrolyticfluid as it can cause severe burns orpermanent eye injury.
�
Wear protective eye gear when han-dling or working near batteries.
Antidote (EXTERNAL):
�
SKIN - Flush with water.
�
EYES - Flush with water for 15 minutesand get immediate medical attention.
Antidote (INTERNAL):
�
Drink large quantities of water or milkfollowed by milk of magnesia, beatenegg, or vegetable oil. Get immediatemedical attention.
Batteries also generate explosive hydro-gen gas; therefore, you should alwaysfollow these preventive measures:
�
Charge batteries in a well-ventilated ar-ea.
�
Keep batteries away from fire, sparks,or open flames (for example: weldingequipment, lighted cigarettes, and soon.)
�
DO NOT SMOKE when charging or han-dling batteries.
KEEP BATTERIES AND ELECTROLYTIC
FLUID OUT OF REACH OF CHILDREN.
CAUTION:
ECM00360
�
A poorly maintained battery will quickly
deteriorate.
�
Ordinary tap water contains mineralsharmful to a battery, and should not be
used for topping up.
1. Check the electrolyte level at least oncea month. Fill to the manufacturer’s rec-ommended level when necessary. Topup only with distilled water (or pure de-ionized water suitable to use in batter-ies).
2. Always keep the battery in a good stateof charge. Installing a voltmeter will helpyou monitor your battery. If you will notuse the boat for a month or more, re-move the battery from the boat and storeit in a cool, dark place. Completely re-charge the battery before using it.
3. If the battery will be stored for longerthan a month, check the specific gravityof the fluid at least once a month and re-charge the battery when it is low.
NOTE:
Consult a Yamaha dealer when charging or
re-charging batteries.
EMU29331
Connecting the battery
WARNING
EWM00570
Mount the battery holder securely in adry, well-ventilated, vibration-free loca-
Maintenance
74
tion in the boat. Install a fully charged bat-
tery in the holder.
CAUTION:
ECM01121
�
Make sure the main switch (on applica-ble models) is “ ” (off) before work-ing on the battery.
�
Reversal of the battery cables will dam-age the electrical parts.
�
Connect the red battery cable firstwhen installing the battery and discon-nect the black battery cable first whenremoving it. Otherwise, the electricalparts can be damaged.
�
The electrical contacts of the batteryand cables must be clean and properlyconnected, or the battery will not start
the engine.
Connect the red battery cable to the POSI-TIVE (+) terminal first. Then connect theblack battery cable to the NEGATIVE (-) ter-minal.
EMU29370
Disconnecting the battery
Disconnect the BLACK cable from the NEG-ATIVE (-) terminal first. Then disconnect theRED cable from the POSITIVE (+) terminal.
EMU29390
Checking top cowling
Check the fitting of the top cowling by push-ing it with both hands. If it is loose have it re-paired by your Yamaha dealer.
EMU29400
Coating the boat bottom
A clean hull improves boat performance. Theboat bottom should be kept as clean of ma-rine growth as possible. If necessary, theboat bottom can be coated with an anti-foul-ing paint approved for your area to inhibitmarine growth.Do not use anti-fouling paint which includescopper or graphite. These paints can causemore rapid engine corrosion.
1. Red cable2. Black cable3. Battery
ZMU04246
75
Trouble Recovery
EMU29424
Troubleshooting
A problem in the fuel, compression, or igni-tion systems can cause poor starting, loss ofpower, or other problems. This section de-scribes basic checks and possible remedies,and covers all Yamaha outboard motors.Therefore some items may not apply to yourmodel.If your outboard motor requires repair, bringit to your Yamaha dealer.If the engine trouble warning indicator isflashing, consult your Yamaha dealer.
Starter will not operate.
Q. Is battery capacity weak or low?A. Check battery condition. Use battery ofrecommended capacity.
Q. Are battery connections loose or corrod-ed?A. Tighten battery cables and clean batteryterminals.
Q. Is fuse for electric start relay or electric cir-cuit blown?A. Check for cause of electric overload andrepair. Replace fuse with one of correct am-perage.
Q. Are starter components faulty?A. Have serviced by a Yamaha dealer.
Q. Is shift lever in gear?A. Shift to neutral.
Engine will not start (starter operates).
Q. Is fuel tank empty?A. Fill tank with clean, fresh fuel.
Q. Is fuel contaminated or stale?
A. Fill tank with clean, fresh fuel.
Q. Is fuel filter clogged?A. Clean or replace filter.
Q. Is starting procedure incorrect?A. See page 42.
Q. Has fuel pump malfunctioned?A. Have serviced by a Yamaha dealer.
Q. Are spark plug(s) fouled or of incorrecttype?A. Inspect spark plug(s). Clean or replacewith recommended type.
Q. Are spark plug cap(s) fitted incorrectly?A. Check and re-fit cap(s).
Q. Is ignition wiring damaged or poorly con-nected?A. Check wires for wear or breaks. Tightenall loose connections. Replace worn or bro-ken wires.
Q. Are ignition parts faulty?A. Have serviced by a Yamaha dealer.
Q. Is engine stop switch lanyard not at-tached?A. Attach lanyard.
Q. Are engine inner parts damaged?A. Have serviced by a Yamaha dealer.
Engine idles irregularly or stalls.
Q. Are spark plug(s) fouled or of incorrecttype?A. Inspect spark plug(s). Clean or replacewith recommended type.
Trouble Recovery
76
Q. Is fuel system obstructed?A. Check for pinched or kinked fuel line orother obstructions in fuel system.
Q. Is fuel contaminated or stale?A. Fill tank with clean, fresh fuel.
Q. Is fuel filter clogged?A. Clean or replace filter.
Q. Have ignition parts failed?A. Have serviced by a Yamaha dealer.
Q. Has warning system activated?A. Find and correct cause of warning.
Q. Is spark plug gap incorrect?A. Inspect and adjust as specified.
Q. Is ignition wiring damaged or poorly con-nected?A. Check wires for wear or breaks. Tightenall loose connections. Replace worn or bro-ken wires.
Q. Is specified engine oil not being used?A. Check and replace oil as specified.
Q. Is thermostat faulty or clogged?A. Have serviced by a Yamaha dealer.
Q. Are carburetor adjustments incorrect?A. Have serviced by a Yamaha dealer.
Q. Is fuel pump damaged?A. Have serviced by a Yamaha dealer.
Q. Is air vent screw on fuel tank closed?A. Open air vent screw.
Q. Is choke knob pulled out?
A. Return to home position.
Q. Is motor angle too high?A. Return to normal operating position. Q. Is carburetor clogged?A. Have serviced by a Yamaha dealer.
Q. Is fuel joint connection incorrect?A. Connect correctly.
Q. Is throttle valve adjustment incorrect?A. Have serviced by a Yamaha dealer.
Q. Is battery cable disconnected?A. Connect securely.
Warning buzzer sounds or indicatorlights.
Q. Is cooling system clogged?A. Check water intake for restriction.
Q. Is engine oil level low?A. Fill oil tank with specified engine oil.
Q. Is heat range of spark plug incorrect?A. Inspect spark plug and replace it with rec-ommended type.
Q. Is specified engine oil not being used?A. Check and replace oil with specified type.
Q. Is engine oil contaminated or deteriorat-ed?A. Replace oil with fresh, specified type.
Q. Is oil filter clogged?A. Have serviced by a Yamaha dealer.
Q. Has oil feed/injection pump malfunc-tioned?
Trouble Recovery
77
A. Have serviced by a Yamaha dealer.
Q. Is load on boat improperly distributed?A. Distribute load to place boat on an evenplane.
Q. Is water pump or thermostat faulty?A. Have serviced by a Yamaha dealer.
Q. Is there excess water in fuel filter cup?A. Drain filter cup.
Engine power loss.
Q. Is propeller damaged?A. Have propeller repaired or replaced.
Q. Is propeller pitch or diameter incorrect?A. Install correct propeller to operate out-board at its recommended speed (r/min)range.
Q. Is trim angle incorrect?A. Adjust trim angle to achieve most efficientoperation.
Q. Is motor mounted at incorrect height ontransom?A. Have motor adjusted to proper transomheight.
Q. Has warning system activated?A. Find and correct cause of warning.
Q. Is boat bottom fouled with marine growth?A. Clean boat bottom.
Q. Are spark plug(s) fouled or of incorrecttype?A. Inspect spark plug(s). Clean or replacewith recommended type.
Q. Are weeds or other foreign matter tangledon gear housing?A. Remove foreign matter and clean lowerunit.
Q. Is fuel system obstructed?A. Check for pinched or kinked fuel line orother obstructions in fuel system.
Q. Is fuel filter clogged?A. Clean or replace filter.
Q. Is fuel contaminated or stale?A. Fill tank with clean, fresh fuel.
Q. Is spark plug gap incorrect?A. Inspect and adjust as specified.
Q. Is ignition wiring damaged or poorly con-nected?A. Check wires for wear or breaks. Tightenall loose connections. Replace worn or bro-ken wires.
Q. Have electrical parts failed?A. Have serviced by a Yamaha dealer.
Q. Is specified fuel not being used?A. Replace fuel with specified type.
Q. Is specified engine oil not being used?A. Check and replace oil with specified type.
Q. Is thermostat faulty or clogged?A. Have serviced by a Yamaha dealer.
Q. Is air vent screw closed?A. Open the air vent screw.
Q. Is fuel pump damaged?A. Have serviced by a Yamaha dealer.
Trouble Recovery
78
Q. Is fuel joint connection incorrect?A. Connect correctly.
Q. Is heat range of spark plug incorrect?A. Inspect spark plug and replace it with rec-ommended type.
Q. Is high pressure fuel pump drive belt bro-ken?A. Have serviced by a Yamaha dealer.
Q. Is engine not responding properly to shiftlever position?A. Have serviced by a Yamaha dealer.
Engine vibrates excessively.
Q. Is propeller damaged?A. Have propeller repaired or replaced.
Q. Is propeller shaft damaged?A. Have serviced by a Yamaha dealer.
Q. Are weeds or other foreign matter tangledon propeller?A. Remove and clean propeller.
Q. Is motor mounting bolt loose?A. Tighten bolt.
Q. Is steering pivot loose or damaged?A. Tighten or have serviced by a Yamahadealer.
EMU29433
Temporary action in emergency
EMU29440
Impact damage
WARNING
EWM00870
The outboard motor can be seriously
damaged by a collision while operating ortrailering. Damage could make the out-
board motor unsafe to operate.
If the outboard motor hits an object in the wa-ter, follow the procedure below.
1. Stop the engine immediately.2. Inspect the control system and all com-
ponents for damage. Also inspect theboat for damage.
3. Whether damage is found or not, returnto the nearest harbor slowly and careful-ly.
4. Have a Yamaha dealer inspect the out-board motor before operating it again.
EMU29450
Running single engine
When using only engine in an emergency, besure to keep the unused one tilted up and op-erate the other engine at low speed.
CAUTION:
ECM00370
If the boat is operated with one engine inthe water but not running, water may runinto the exhaust pipe due to wave action,
causing engine trouble.
NOTE:
When you are maneuvering at low speed,such as near a dock, it is recommended thatboth engines be running with one in neutral
gear if possible.
Trouble Recovery
79
EMU29480
Replacing fuse
If the fuse has blown on an electric startmodel, remove the electrical cover, open thefuse holder, and replace the fuse with a newone of the proper amperage.
WARNING
EWM00630
Be sure to use the specified fuse. An in-correct fuse or a piece of wire could allowexcessive current flow. This could cause
electric system damage and a fire hazard.
NOTE:
Consult your Yamaha dealer if the new fuse
immediately blows again.
EMU29522
Power trim and tilt / power tilt will not operate
If the engine cannot be tilted up or down with
1. Electrical cover2. Fuse holder3. Fuse (20 A
×
2, 30 A
×
2)4. Spare fuse (20 A, 30 A)5. Fuse puller
1. Fuse puller
12
2
34
5
ZMU04279
1
ZMU04280
Trouble Recovery
80
the power trim and tilt / the power tilt becauseof a discharged battery or a failure with thepower trim and tilt unit / the power tilt unit, theengine can be tilted manually.1. Loosen the manual valve screw by turn-
ing it counterclockwise until it stops.
2. Put the engine in the desired position,then tighten the manual valve screw byturning it clockwise.
EMU31780
Water separator warning indicator blinks while cruising
WARNING
EWM01500
Gasoline is highly flammable, and its va-pors are flammable and explosive.
�
Do not perform this procedure on a hotor running engine. Allow the engine tocool.
�
There will be fuel in the fuel filter. Keepaway from sparks, cigarettes, flames orother sources of ignition.
�
This procedure will allow some fuel tospill. Catch fuel in a rag. Wipe up anyspilled fuel immediately.
�
The fuel filter must be reassembledcarefully with the O-ring, filter cup, andhoses in place. Improper assembly orreplacement could result in a fuel leak,
which could result in a fire or explosion
hazard.
If the water separator warning indicator onthe tachometer blinks, perform the followingprocedure.
1. Stop the engine.2. Remove the top cowling.3. Disconnect the water detection switch
coupler.
CAUTION:
ECM01570
Be careful not to get any water on the wa-ter detection switch coupler, otherwise a
malfunction could occur.
4. Unscrew the filter cup from the filterhousing.
1. Manual valve screw
ZMU03464
1
1. Water separator warning indicator
1. Water detection switch coupler
1 ZMU05480
Trouble Recovery
81
NOTE:
Be careful not to twist the water detection
switch lead when unscrewing the filter cup.
5. Drain the water in the filter cup by soak-ing it up with a rag.
NOTE:
Properly dispose of the rag.
6. Firmly screw the filter cup onto the filterhousing.
NOTE:
Be careful not to twist the water detectionswitch lead when screwing the filter cup onto
the filter housing.
7. Connect the water detection switch cou-pler securely until a click is heard.
8. Install the top cowling.9. Start the engine and make sure that the
water separator warning indicator re-mains off.
NOTE:
Have a Yamaha dealer inspect the outboard
motor after returning to port.
EMU29541
Starter will not operate
If the starter mechanism does not operate(the engine cannot be cranked with the start-er), the engine can be started manually withan emergency starter rope. However, the en-gine cannot be started manually if the batteryvoltage is low. If the battery is discharged to9 volts or below, the electric fuel pump willnot operate.
WARNING
EWM01021
�
Use this procedure only in an emergen-cy to return to the nearest port for re-pairs.
�
When the emergency starter rope isused to start the engine, the start-in-gear protection device does not oper-ate. Make sure the remote control leveris in neutral. Otherwise the boat couldunexpectedly start to move, whichcould result in an accident.
�
Attach the engine stop switch lanyardto a secure place on your clothing, oryour arm or leg while operating theboat.
�
Do not attach the lanyard to clothingthat could tear loose. Do not route thecord where it could become entangled,preventing it from functioning.
�
Avoid accidentally pulling the lanyardduring normal operation. Loss of en-gine power means the loss of moststeering control. Also, without engine
1. Filter cup2. Water detection switch lead
1. Water detection switch coupler
12 ZMU05479
1 ZMU05503
Trouble Recovery
82
power, the boat could slow rapidly. Thiscould cause people and objects in theboat to be thrown forward.
�
Make sure no one is standing behindyou when pulling the starter rope. Itcould whip behind you and injuresomeone.
�
An unguarded, rotating flywheel is verydangerous. Keep loose clothing andother objects away when starting theengine. Use the emergency starter ropeonly as instructed. Do not touch the fly-wheel or other moving parts when theengine is running. Do not install thestarter mechanism or top cowling afterthe engine is running.
�
Do not touch the ignition coil, sparkplug wire, spark plug cap, or other elec-trical components when starting or op-erating the motor. You could get an
electrical shock.
EMU29643
Emergency starting engine
1. Remove the top cowling.2. Remove the two bolts holding the fly-
wheel cover.3. Lift up the rear of flywheel cover and pull
it forward to remove it.
4. Prepare the engine for starting. For fur-ther information, see page 42. Be surethe engine is in neutral and that the en-
gine stop switch lanyard lock plate is at-tached to the engine stop switch. Themain switch must be “ ” (on).
5. Insert the knotted end of the emergencystarter rope into the notch in the flywheelrotor and wind the rope around the fly-wheel clockwise.
6. Pull the rope slowly until resistance isfelt.
7. Remove the rope from the flywheel tem-porarily.
ZMU04250
ZMU02334
ONSTARTOFF
ONSTARTOFF
ZMU04589
Trouble Recovery
83
8. Rewind the rope around the flywheel ap-proximately 3/4 of a turn clockwise.
9. Give a strong pull straight out to crankand start the engine. Repeat if neces-sary.
EMU29760
Treatment of submerged motor
If the outboard motor is submerged, immedi-ately take it to a Yamaha dealer. Otherwisesome corrosion may begin almost immedi-ately.If you cannot immediately take the outboardmotor to a Yamaha dealer, follow the proce-dure below in order to minimize engine dam-age.
EMU29790
Procedure
1. Thoroughly wash away mud, salt, sea-weed, and so on, with fresh water.
2. Remove the spark plugs and face thespark plug holes downward to allow anywater, mud, or contaminants to drain.
3. Drain the fuel from the vapor separator,fuel filter, and fuel line.
4. Feed fogging oil or engine oil throughthe intake manifold and spark plug holeswhile cranking with the emergency start-er rope.
5. Take the outboard motor to a Yamaha
dealer as soon as possible.
CAUTION:
ECM00400
Do not attempt to run the outboard motor
until it has been completely inspected.
ZMU04272
84
Consumer information
EMU29811
Important warranty information for U.S.A. and Canada
Consumer information
85
Consumer information
86
EMU29830
YAMAHA MOTOR CORPORATION, U.S.A. FOUR-STROKE OUTBOARD MOTOR THREE-YEAR LIMITED WARRANTY
Consumer information
87
Consumer information
88
EMU29841
IMPORTANT WARRANTY INFORMATION IF YOU USE YOUR YAMAHA OUTSIDE THE USA OR CANADA
68V-9-18 Hyoshi 06.2.24 9:20 ページ 3
Printed in JapanApril 2006–2.1 × 1 ! Printed on recycled paper
68V-9-18 Hyoshi 06.2.24 9:20 ページ 4
YAMAHA MOTOR CO., LTD.MADE IN JAPANPAYS D'ORIGINE JAPON
OUTBOARD MOTOR WARRANTY REGISTRATION
ENREGISTREMENT DE LA GARANTIE DU MOTEUR HORS-BORD
Please complete and mail this card. This information is necessary to accurately register your unit for warranty.Veuillez signer ci-dessous pour attester que le montage et l’inspection ont été faits dans le respect des directives d’inspection et
que la marche à suivre pour la garantie et l’entretien a été expliquée à l’acheteur au détail.
OUTBOARD MOTOR MODEL AND SERIAL NUMBER (From I.D. label on clamp bracket)MODÉLE ET NO. DE SÉRIE DU MOTEUR HORS-BORD (sur l’étiquette d’identification de la presse de fixation)
(For Dealer Use Only)(A l’usage du concessionnaire)YAMAHA DEALER NUMBERNO. DU CONCESSIONNAIRE YAMAHA
DEALER NAMENOM DU CONCESSIONNAIRE
DATE SOLDDATE DELIVRAISON
OWNER’S NAMENOM DUPROPRIÉTAIRE
ADDRESSADRESSE
PHONE NUMBER ( )NUMÉRO DE TÉLÉPHONE
USAGE(Check One)UTILISATION(En cocher un.)
PLEASURELOISIRCOMMERCIALCOMMERCIAL
MONTH DAY YEARMOIS JOUR ANNÉE
FIRST LASTPRÉNOM NOM DE FAMILLE
STREETRUE
CITY STATE/PROVINCE ZIPVILLE PROVINCE CODE POSTAL
Warranty card-04 2/17/03 2:41 PM Page 1
PLACEPOSTAGEHERE
ATTN: WARRANTY DEPARTMENT
Warranty card-04 2/17/03 2:41 PM Page 2