extron fox ii t/r dp 4k • setup guide, rev. b · 2020. 11. 24. · the fox ii t/r dp 4k outputs...
TRANSCRIPT
![Page 1: Extron FOX II T/R DP 4K • Setup Guide, rev. B · 2020. 11. 24. · The FOX II T/R DP 4K outputs continuous invisible light (Class 1 rated), which may be harmful to the eyes; use](https://reader035.vdocuments.us/reader035/viewer/2022081516/61459ed107bb162e665fcd5e/html5/thumbnails/1.jpg)
1
IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
FOX II T/R DP 4K • Setup GuideThis guide provides quick start instructions for an experienced installer to set up and operate the Extron FOX II T/R DP 4K Fiber Optic Extenders.
WARNING: The FOX II T/R DP 4K outputs continuous invisible light (Class 1 rated), which may be harmful to the eyes; use with caution. Plug the attached dust caps into the optical transceivers when the fiber cable is unplugged.
CLASS 1 LASER PRODUCT, see the FOX II T/R DP 4K User Guide, at www.extron.com.
AVERTISSEMENT : Le FOX II T/R DP 4K émet une lumière invisible en continu (conforme à la classe 1) qui peut être dangereux pour les yeux, à utiliser avec précaution. Branchez les protections contre la poussière dans l’ensemble émetteur/récepteur lorsque le câble fibre optique est débranché.
Produit laser de classe 1, voir le FOX II T/R DP 4K User Guide sur www.extron.com (en anglais).
Installation
FOX II DP 4K Transmitter Rear Panel
FOX II DP 4K Receiver Rear Panel
100-240V ~ -.-A MAX
50-60 HzDISPLAYPORT LOOP THRU
L R RS-232
OPTICAL
Tx
RESETLIN
K
LIN
K
Rx
RS-232 IR
ALARM
Tx Rx G 1 2
L R
Tx Rx Tx RxG
AUDIO
INPUTS AUDIORETURN OUT
REMOTE
OV
ER
FI
BE
R FOX T DP 4K
100-240V ~ -.-A MAX
50-60 HzDISPLAYPORT
L R RS-232
OPTICAL
Tx
RESETLIN
K
LIN
K
Rx
RS-232 IR
ALARM
Tx Rx G 1 2
L R
Tx Rx Tx RxG
AUDIO
OUTPUTS AUDIORETURN IN
REMOTE
OV
ER
FI
BE
R FOX R DP 4K
Step 1 — MountingTurn off or disconnect all equipment power sources and mount the transmitter and receiver as required. For mounting details and considerations, see the FOX II T/R DP 4K User Guide at www.extron.com.
Step 2 — Input and Output Connectionsa. Connect a DisplayPort
DISPLAYPORT LOOP THRU
video source to the transmitter DisplayPort input connector.
b. If desired, connect a DisplayPort video display to the transmitter Loop-Thru connector for a local display.
c. Connect a DisplayPort video display to the receiver DisplayPort output connector. DISPLAYPORT
d. Connect an audio input device to either the Audio 3.5 mm mini jack or the Audio 5-pole captive screw connector L R
AUDIO on the transmitter. See the drawing below step 2g to make connections on the captive screw connector.
e. Connect an audio output device to either or both the 3.5 mm mini jack or the Audio 5-pole captive screw connector on the receiver. See the drawing below step 2g to make connections on the captive screw connector.
f. For optional returned audio, connect an audio output device to the Audio Return Out 5-pole captive screw
L R
AUDIORETURN OUT
L R
AUDIORETURN IN
connector on the transmitter. See the drawing below step 2g to make connections on the captive screw connector.
g. For optional returned audio, connect an audio input device to the Audio Return In 5-pole captive screw connector on the receiver. See the drawing below to make connections on the captive screw connector.
ATTENTION:• For unbalanced audio, connect the sleeves to the
ground contact. DO NOT connect the sleeves to the negative (–) contacts.
• Pour l’audio asymétrique, connectez les manchons au contact au sol. Ne PAS connecter les manchons aux contacts négatifs (–).
NOTE: For returned audio, above, and RS-232 and IR responses (from the receiver to the transmitter), on the next page, you must install the receiver-Tx-to-transmitter-Rx cable in step 3b.
Unbalanced Stereo Output Balanced Stereo Output
Unbalanced Stereo Input Balanced Stereo Input
Do not tin the wires!
Tip
No Ground Here
No Ground Here
Tip
LR
Sleeves
TipRing
TipRing
LR
Sleeves
TipRing
TipRing
LR
SleevesTip
Sleeve
SleeveTip
LR
![Page 2: Extron FOX II T/R DP 4K • Setup Guide, rev. B · 2020. 11. 24. · The FOX II T/R DP 4K outputs continuous invisible light (Class 1 rated), which may be harmful to the eyes; use](https://reader035.vdocuments.us/reader035/viewer/2022081516/61459ed107bb162e665fcd5e/html5/thumbnails/2.jpg)
2
FOX II T/R DP 4K • Setup Guide (Continued)
h. If you want the FOX II DP 4K units to pass serial or IR data or control signals, such as for serial Rx TxGnd
Tx RxGnd
IR Device
RS-232 Device
RS
-232IR
Tx
Rx
Tx
Rx
G
OVER FIBER
control of a projector, connect the master device to the transmitter and the controlled device to the receiver via the Over Fiber 5-pole captive screw connectors on both units.
i. For remote monitoring of the status of the Rx optical link on either the transmitter or RS-232 ALARM
Tx Rx G 1 2
REMOTE receiver, connect a locally constructed or obtained device to the two rightmost poles of the Alarm and Remote RS-232 5-pole captive screw connector on that unit. The unit shorts both poles together when no light is detected.
NOTE: The transmitter port reports the status of the link from the receiver. The receiver port reports the status of the link from the transmitter.
j. For remote control of a unit and for loading firmware, connect a host device, such as a computer or control system, to either of the following ports on the unit to be controlled:
Configuration port — The front panel USB mini-B connector. CONFIG
NOTE: Extron recommends performing firmware updates via the Configuration port only.
Remote RS-232 port — The rear panel Remote RS-232 port, the 3 leftmost poles of this 5-pole captive screw connector. RS-232 ALARM
Tx Rx G 1 2
REMOTE The protocol for the Remote port is as follows:
• 9600 baud • no parity • 8 data bits• 1 stop bit • no flow control
Step 3 — Throughput Connections
Receiver
Transmitter11
22
22
11
OPTICAL
Tx
LIN
K
LIN
K
Rx
OPTICAL
Tx
LIN
K
LIN
K
Rx
NOTE: See the two fiber cable connection drawing at right. You can connect the transmitter and receiver in one of two ways:
• One way (transmitter to receiver) only, perform step 3a.
• Two way (transmitter to receiver and return), perform steps 3a and 3b.
a. Connect the fiber between the Tx port on the transmitter and the Rx port on the receiver (1, at right).
NOTE: Ensure that the transmitter and connected receiver are the same transmission mode, singlemode (SM) or multimode (MM) and that you use the correct SM or MM fiber cable to connect the devices.
b. If you want the receiver to return serial data (such as responses from a controlled device), IR data, or returned audio to the transmitter, connect a cable between the Tx port on the receiver and Rx port on the transmitter (2).
Tx Link and Rx Link LEDs — When lit, the link is active (light is output [Tx] or received [Rx]).
NOTE: The Link LEDs indicate transmission of light only, not whether there is data encoded in the optical link.
![Page 3: Extron FOX II T/R DP 4K • Setup Guide, rev. B · 2020. 11. 24. · The FOX II T/R DP 4K outputs continuous invisible light (Class 1 rated), which may be harmful to the eyes; use](https://reader035.vdocuments.us/reader035/viewer/2022081516/61459ed107bb162e665fcd5e/html5/thumbnails/3.jpg)
3
Operation
After the receiver, the transmitter, and their connected devices are powered up, the system is fully operational. If any problems are encountered, verify that the cables are routed and connected properly and that the display device has a compatible resolution and refresh rate. If problems persist, call the Extron S3 Sales & Technical Support Hotline. See the contact numbers on the last page of this guide for the Extron office nearest you.
Indications
NOTE: The figure below right is of a receiver. A transmitter has similar indications.
Power ( ) LED — Indicates that power is applied to the unit.
CONFIG SIGNAL
VIDEO AUDIO
HDCP
OUTPUT
RETURN IN
Video LEDs —
Signal LED — Lights on both units when the unit detects an input video signal.
HDCP LED — Lights on both units when the input signal is HDCP encrypted.
Audio LEDs —
Input LED (transmitter) — Lights when an analog audio or PCM digital audio signal remains above -35 dBV. The LED goes unlit if the audio signal level drops below the threshold for 10 seconds or longer.
Output LED (receiver) — Lights when an analog audio or PCM digital audio signal remains above -35 dBV. The LED goes unlit if the audio signal level drops below the threshold for 10 seconds or longer.
Return Out LED (transmitter) — Lights when analog audio is present on the transmitter Return Audio Output connector.
Return In LED (receiver) — Lights when analog audio is present on the receiver Return Audio Input connector.
EDID (Transmitter) SELECTEDID
EDID Select rotary switch — Set this switch to one of the positions shown in the table below to select the source of the EDID or a specific resolution.
Position 0 — An EDID that has previously been captured from a connected display or manually imported via an SIS command or the Product Configuration Software.
Position 1 — The EDID is selected via the Remote or USB port on the transmitter only, using an SIS command or the Extron Product Configuration Software.
Position 2 — Use the EDID from the display connected to the receiver.
NOTE: EDID from the display connected to the receiver requires connection of both fiber cables.
Position 3 — Use the EDID from the display connected to the transmitter loop-through.
Positions 4 through E — Specify a resolution. The table at right identifies the resolutions associated with the switch positions. All resolutions are at 60 Hz with the exception of 3840x2160 (E), which is 30 Hz.
Position F — No EDID assigned.
Remote controlSee the FOX II T/R DP 4K User Guide, available at www.extron.com, for details on operating and monitoring the transmitter and receiver using either SIS commands or the Extron Product Configuration Software.
Pos. Source or resolution Pos. Resolution Pos. Resolution0 User recorded EDID 6 1366x768 C 2048x21601 Selected via RS-232 7 1440x900 D 2560x16002 Display on Rx output 8 1680x1050 E* 3840x21603 Display on Tx loop-through 9 1920x1080 F N/A4 1280x720 A 1920x12005 1280x800 B 2048x1536
* 30 Hz
![Page 4: Extron FOX II T/R DP 4K • Setup Guide, rev. B · 2020. 11. 24. · The FOX II T/R DP 4K outputs continuous invisible light (Class 1 rated), which may be harmful to the eyes; use](https://reader035.vdocuments.us/reader035/viewer/2022081516/61459ed107bb162e665fcd5e/html5/thumbnails/4.jpg)
468-2540-50 Rev. B
01 16
Extron Headquarters+800.633.9876 Inside USA/Canada Only
Extron USA - West Extron USA - East+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX +1.919.850.1001 FAX
Extron Europe+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia+65.6383.4400
+65.6383.4664 FAX
Extron Japan+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East+971.4.299.1800
+971.4.299.1880 FAX
Extron Korea+82.2.3444.1571
+82.2.3444.1575 FAX
Extron India1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
© 2016 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
FOX II T/R DP 4K • Setup Guide (Continued)
Application Diagram
STANDBY
CLASS 2 WIRING
1
2
XPA 1002
LEVEL
1
12
1
2
LIMITER/
PROTECT
SIGNAL
2
INPUTS
OUTPUT
REMOTE
0
0
VOL/MUTE
10V50 mA
100-240V 1.3A, 50-60Hz
100-24
0V ~ -.-A MAX
50-60 Hz
DISPLAYPORT
L
R
RS-232 OPTICAL
TxRESET
LIN
K
LIN
K
Rx
RS-232IR
ALARM
Tx RxG
12
L
R
Tx RxTx Rx
G
AUDIO
OUTPUTS
AUDIO
RETURN IN REMOTE
OV
ER
FI
BE
R
FOX R DP 4K
100-24
0V ~ -.-A MAX
50-60 Hz
DISPLAYPORT
LOOP THRU
L
R
RS-232 OPTICAL
TxRESET
LIN
K
LIN
K
Rx
RS-232IR
ALARM
Tx RxG
12
L
R
Tx RxTx Rx
G
AUDIO
INPUTS
AUDIO
RETURN OUT REMOTE
OV
ER
FI
BE
R
FOX T DP 4K
POWER
12V
--A MAX
G
TxRx
RTS CTS
COM 1G
TxRx
COM 2
VC
GVOL
RELAYS
1 2 C
1 2 3 4 G
DIGITAL I/O
PWR OUT = 6W
eBUS
+V +S -SG
LAN
IPCP PRO 250
IR/S
S G
MODEL 80
ExtronExtro
nHelp
System
Off
Display
Room
Control
Off
Mute
Screen
Lighting
December 15, 2013 - 7:58 AM
Audio
Control
Volume
Mute
Tuner 1 2 3
VCR
Laptop
PC
DVD
Doc
Cam
Tuner
On
Channel
Last
Presets
More
Presets
32
1 65
4 98
7 Enter
0
RS-232
Ethernet
Ethernet
Audio
4K DisplayPort
4K DisplayPort
4K DisplayPort
ExtronSI 28Surface-mountSpeakers
ExtronXPA 1002PowerAmpli�er
4K Display
PC
Local Monitor
Up to 30 km (18.75 miles)Singlemode FiberSM Model
Audio
RS-232
ExtronFOX T DP 4KFiber Optic Transmitter
ExtronFOX R DP 4KFiber Optic Receiver
ExtronTLP Pro 720T7" Table TopTouchLink Pro Touchpanel
TCP/IPNetwork
Extron IPCP Pro 250IP Link Pro Control Processor