exp floor 34-65
TRANSCRIPT
34 Multi-Flex Enclosures
THE
NETH
ERLA
ND
USA
CANA
DA
GERM
ANY
GERM
ANY
GERM
ANY
ENGL
AND
NORW
AY
FRAN
CE
Type ofenclosure
MKS
MKD
MCS
MCD
MCI
Series Material Nr. ofdoors
Protection level
Kompact version,single door
Mild Steel 1 IP 66NEMA 4, 12, 13
Kompact version,double door
Mild Steel 2 IP 55NEMA 12, 13
Combination version,single door
Mild Steel 1 IP 55NEMA 12, 13
Combination version,double door
Mild Steel 2 IP 55NEMA 12, 13
Industrial ICT enclosure
Mild Steel 1 IP 55NEMA 12, 13
EARTHINGPersonal protectionThe Eldon enclosures are provided with various earthing points. All panels (excluding certain gland plates) are equipped with a copper-platedor stainless steel earthing stud.The frame or body of the Stainless steel enclosures, and the wall mountingenclosures (Multi-Mount®) have two studs so one can be used as a ProtectedEarth (PE). The frames of the Multi-Flex® series, MCS, MCD, MKS, MKD are equippedwith contact washers so the earthing points can be mounted on any spaceavailable. To ensure that these earthing points will give you the desired pro-tection, Eldon has verified their products by testing at the independent insti-tute TNO in The Netherlands.
Technical details measured between:Panel earthingPE - mild steel copper-plated stud M6 1,19 mΩPE - mild steel copper-plated stud M8 1,06 mΩ
Frame earthingPE - mild steel copper-plated stud M8 0,51 mΩ
General earthingPE - mild steel zinc-plated bolt connection with contact washers M6 (bottom plate) 1,64 mΩPE - mild steel zinc-plated bolt connection with contact washers M8 (Open frame) 1,83 mΩPE- mild steel zinc-plated bolt connection with contact washers M10(Suiting frames together) 0,78 mΩ
Earthing cablesCUF 220, 6 mm2 copper, cable eyes for M6/M8, length 220 mm 1,05 mΩCUF 300, 6 mm2 copper, cable eyes for M8 length 300 mm 1,29 mΩ
NB For stainless steel the resistance is approximately 3 times higher than for mild steel.
Tested
Floor Standing Enclosures
Page36 MCS, Combination version, single door37 MCD, Combination version, double door38 MKS, Kompact version, single door39 MKD, Kompact version, double door40 MCI, Industrial Data enclosure44 Accessories
35Multi-Flex Enclosures
MCS
MCD
Page 36
Page 37
MKS
Page 38
MKD
Page 39
MCI
Page 40
36 Multi-Flex Enclosures
MCS
Without mounting plateH W D Cat.no.
1800 600 400 MCS 18064 PE500 MCS 18065 PE
800 400 MCS 18084 PE500 MCS 18085 PE
1000 400 MCS 18104 PE500 MCS 18105 PE
2000 600 400 MCS 20064 PE500 MCS 20065 PE600 MCS 20066 PE800 MCS 20068 PE
800 400 MCS 20084 PE500 MCS 20085 PE600 MCS 20086 PE800 MCS 20088 PE
1000 400 MCS 20104 PE500 MCS 20105 PE600 MCS 20106 PE
2200 600 800 MCS 22068 PE800 600 MCS 22086 PE
800 MCS 22088 PE
IP 56/NEMA 4, 12,13
MCS, Combination version, single door
Material: Frame: 1.75 mm painted steel. Door: 2.0 mmpainted steel. Rear, roof and side panels: 1.5 mm pain-ted steel. Mounting plate: 3 mm galvanised steel.Bottom plates: 1.5 mm galvanised steel.Frame: Seamwelded reversed open profiles with 25 mmhole pattern according to DIN 43660. Including integra-ted external hole pattern.Door: Surface mounted with hinges allowing left or righthand opening. Including door frame with 25 mm holepattern.Rear panel: Fitted by M6 torx screws. Standard facilitiesfor rear door mounting.Side panels: Supplied as an accessory.Roof panel: Removable.Bottom plates: Consists of three pieces.Lock: Espagnolette 4-point locking system. Does notinterfere with the enclosure inner space. Standard DIN-lock with 3 mm pin. Can be exchanged for standardinserts or Euro-cylinder, swing handle or digital lockingsystem. Swing handle fitted as standard for UK market.Mounting plate: Double folded and slides into position.Adjustable in depth by steps of 25 mm. Attached onthe outside of the enclosure carton.Earthing: All panels are earthed through their fittings.Finish: RAL 7032 polyester powder structure paint.Protection: Corresponds with IP 56 and Nema 4, 12and 13.Delivery includes: Frame with fitted door, rear panel,roof panel, bottom plates*, mounting plate* and doorframe*. Delivery also includes earthing bolts. Deliveredon a pallet with width identical with the enclosure toallow suiting without removal. All packing material recy-clable.
With mounting plateH W D Cat.no.
1800 400 500 MCS 18045600 400 MCS 18064
500 MCS 18065800 400 MCS 18084
500 MCS 180851000 400 MCS 18104
500 MCS 181052000 400 400 MCS 20044
500 MCS 20045600 MCS 20046
600 400 MCS 20064500 MCS 20065600 MCS 20066800 MCS 20068
800 400 MCS 20084500 MCS 20085600 MCS 20086800 MCS 20088
1000 400 MCS 20104500 MCS 20105600 MCS 20106
2200 600 800 MCS 22068800 600 MCS 22086
800 MCS 22088* = not included for 400 wide cable enclosures.
37Multi-Flex Enclosures
MCD
IP 55/NEMA 12, 13
MCD, Combination version, double door
Material: Frame:1.75 mm painted steel. Doors: 2.0 mm paintedsteel. Rear, roof and side panels: 1.5 mm painted steel. Mounting plate: 3 mm galvanised steel.Bottom plates: 1.5 mm galvanised steel.Frame: Seamwelded reversed open profiles with 25 mm holepattern according to DIN 43660. Including integrated externalhole pattern.Doors: Surface mounted with four hinges. Including door framewith 25 mm hole pattern.Rear panel: Fitted by M6 torx screws. Standard facilities for reardoor mounting.Side panels: Supplied as an accessory.Roof panel: Removable.Bottom plates: Consists of three piecesLock: Espagnolette 4-point locking system. Does not interferewith the enclosure inner space. Standard DIN-lock with 3 mm pin. Can be exchanged for standard insertsor Euro-cylinder, swing handle or digital locking system. Swinghandle fitted as standard for UK market.Mounting plate: Double folded and adjustable in depth bysteps of 25 mm. Attached on the outside of the enclosure car-ton.Earthing: All panels are earthed through their fittingsFinish: RAL 7032 polyester powder structure paint.Protection: Corresponds with IP 55 and Nema 12, 13Delivery includes: Frame with fitted doors, rear panel, roofpanel, bottom plates*, mounting plate* and door frame*. Deliveryalso includes earthing bolts. Delivered on a pallet with widthidentical with the enclosure to allow suiting without removal. Allpacking material recyclable.
With mounting plateH W D Cat.no.
1800 800 500 MCD 180851000 400 MCD 18104
500 MCD 181051200 400 MCD 18124
500 MCD 181251600 400 MCD 18164
2000 800 500 MCD 200851000 400 MCD 20104
500 MCD 20105600 MCD 20106800 MCD 20108
1200 400 MCD 20124500 MCD 20125600 MCD 20126800 MCD 20128
1600 400 MCD 201642200 1000 600 MCD 22106
1200 600 MCD 22126
Without mounting plateH W D Cat.no.
1800 800 500 MCD 18085PE1000 400 MCD 18104PE
500 MCD 18105PE1200 400 MCD 18124PE
500 MCD 18125PE1600 400 MCD 18164PE
2000 800 500 MCD 20085PE1000 400 MCD 20104PE
500 MCD 20105PE600 MCD 20106PE800 MCD 20108PE
1200 400 MCD 20124PE500 MCD 20125PE600 MCD 20126PE800 MCD 20128PE
1600 400 MCD 20164PE2200 1000 600 MCD 22106PE
1200 600 MCD 22126PE
38 Multi-Flex Enclosures
MKS
IP 66/NEMA 12, 13
MKS, Kompact version, single door
Material: Body, rear and roof panels: 1. 5 mm painted steel. Door:2.0 mm painted steel.Mounting plate: 3 mm galvanised steel.Bottom plates: 1.5 mm galvanised steel.Body: Four times folded and seam-welded frame. Integrated doublerow hole pattern.Door: Surface mounted with hinges allowing left or right hand opening.Including door frame with 25 mm hole pattern.Rear panel: Fitted by M6 torx screws. Standard facilities for rear doormounting.Roof panel: Removable.Bottom plates: Consists of three pieces.Lock: Espagnolette 4-point locking system. Does not interfere with theenclosure inner space. Standard DIN-lock with 3 mm pin. Can be exchanged for standard inserts orEuro-cylinder, swing handle or digital locking system. Swing handle fit-ted as standard for UK market.Mounting plate: Double folded and slides into position. Adjustable indepth by steps of 25 mm. Attached on the outside of the enclosurecarton.Earthing: All panels are earthed through their fittings.Finish: RAL 7032 polyester powder structure paint.Protection: Corresponds with IP 66 and Nema 12, 13.* To achieve IP 66, use gasket kit BG 01 when fitting the bottom plate.Delivery includes: Body with fitted door, rear panel, roof panel, bottomplates, mounting plate and door frame. Delivery also includes earthingbolts. Delivered on a pallet with width identical with the enclosure toallow suiting without removal. All packing material recyclable.
With mounting placeH W D Cat.no.
1600 600 400 MKS 16064800 400 MKS 16084
1000 400 MKS 161041800 600 400 MKS 18064
800 400 MKS 180841000 400 MKS 18104
2000 600 400 MKS 20064800 400 MKS 20084
1000 400 MKS 20104
Without mounting plateH W D Cat.no.
1600 600 400 MKS 16064PE800 400 MKS 16084PE
1000 400 MKS 16104PE1800 600 400 MKS 18064PE
800 400 MKS 18084PE1000 400 MKS 18104PE
2000 600 400 MKS 20064PE800 400 MKS 20084PE
1000 400 MKS 20104PE
39Multi-Flex Enclosures
MKD
Mounting plate: Double folded and adjustable in depth by steps of25 mm. Attached on the outside of the enclosure carton.Finish: RAL 7032 polyester powder structure paint.Protection: Corresponds with IP 55 and NEMA 12, 13Delivery includes: Enclosure with fitted door, roof panel, rear panel,bottom plates, mounting plate and door mounting frame. Delivery alsoincludes earthing bolts. The enclosure is delivered on a pallet identicalto the enclosure width.All packing material recyclable.
Without mounting plateH W D Cat.no.
1600 1200 400 MKD 16124PE1800 1200 400 MKD 18124PE
1600 400 MKD 18164PE2000 1200 400 MKD 20124PE
1600 400 MKD 20164PE
IP 55/NEMA 12, 13
MKD, Kompact version, double door
Material: Body, rear and roof panels: 1. 5 mm painted steel. Door:2.0 mm painted steel. Mounting plate: 3 mm galvanised steel.Bottom plates: 1.5 mm galvanised steel.Body: Four times folded and seam-welded frame. Integrated doublerow hole pattern.Doors: Surface mounted with four hinges allowing left or right handopening. Including door frame with 25 mm hole pattern.Rear panel: Fitted by M6 torx screws. Standard facilities for rear doormounting.Roof panel: Removable.Lock: External espagnolette 4-point locking system. Standard fittedDIN-lock with 3 mm pin. Can be exchanged for standard inserts orEuro-cylinder and swing handle. Swing handle fitted as standard for UKmarket.
With mounting plateH W D Cat.no.
1600 1200 400 MKD 161241800 1200 400 MKD 18124
1600 400 MKD 181642000 1200 400 MKD 20124
1600 400 MKD 20164
40 Multi-Flex Enclosures
MCI
IP 55/Nema 12, 13
MCI, Industrial Data enclosure
Material: Frame 1,75 mm steel plate, 19” profiles and door 2 mm steelplate.Roof plates: 1.5 mm steel plate.Bottom plates: 1.5 mm galvanised steel.Frame: Seamwelded reversed open profiles with 25 mm hole patternaccording to DIN 43660. Including integrated external hole pattern.Rear door: Surface mounted with hinges allowing left or right handopening. Including door frame with 25 mm hole pattern.Side panels: Supplied as an accessory.Roof panel: Removable.Lock: Espagnolette 4-point locking. Standard DIN-lock with 3 mmpin.Can be exchanged for standard inserts or Euro-cylinder and folding
H W D Cat.no.1100 600 600 MCI 110661400 800 600 MCI 140861600 600 600 MCI 160661800 600 600 MCI 180662000 600 600 MCI 20066
800 MCI 20068800 600 MCI 20086
800 MCI 200882200 600 600 MCI 22066
800 MCI 22068800 600 MCI 22086
800 MCI 22088900 MCI 22089
handle.19” profiles: Provide front and side universal punchings.Finish: Frame and roof plates: grey RAL 7032 powder structure paint.19” profiles: Zinc plated.Protection: Corresponds with IP 55 and Nema 12, 13 when front doorand side panels are fitted.Delivery: Frame with fitted rear door, roof panel, bottom plates, 19””profiles at front and fixing brackets DND 01. Delivery also includes ear-thing bolts. Delivered on a pallet with width identical with the enclosu-re to allow combining without removal. All packing material recyclable.
41Multi-Flex Enclosures
www.eldon.com
Eldon Enclosures Systems
Eldon Computer Aided Engineering
More than 80 years
of experience in
manufacturing and
supply of flexible
enclosure systems
for all kind of
applications.
Making solutionsthe answer
Enclosure type H W D Side panel Plinth 100 mm Plinth 100 mm Plinth front/rear* side panel* transversal profiles
MCD 18085 1800 800 500 SPM 1805 PF 1080 PS 1050 PT 05MCD 18104 1800 1000 400 SPM 1804 PF 1100 PS 1040 PT 04MCD 18105 1800 1000 500 SPM 1805 PF 1100 PS 1050 PT 05MCD 18124 1800 1200 400 SPM 1804 PF 1120 PS 1040 PT 05MCD 18125 1800 1200 500 SPM 1805 PF 1120 PS 1050 PT 05MCD 18164 1800 1600 400 SPM 1804 PF 1080 (2x) PS 1040 PT 04MCD 20085 2000 800 500 SPM 2005 PF 1080 PS 1050 PT 05MCD 20104 2000 1000 400 SPM 2004 PF 1100 PS 1040 PT 04MCD 20105 2000 1000 500 SPM 2005 PF 1100 PS 1050 PT 05MCD 20106 2000 1000 600 SPM 2006 PF 1100 PS 1060 PT 06MCD 20108 2000 1000 800 SPM 2008 PF 1100 PS 1080 PT 08MCD 20124 2000 1200 400 SPM 2004 PF 1120 PS 1040 PT 04MCD 20125 2000 1200 500 SPM 2005 PF 1120 PS 1050 PT 05MCD 20126 2000 1200 600 SPM 2006 PF 1120 PS 1060 PT 06MCD 20128 2000 1200 800 SPM 2008 PF 1120 PS 1080 PT 08MCD 20164 2000 1600 400 SPM 2004 PF 1080 (2x) PS 1040 PT 04MCD 18164 1800 1600 400 SPM 1804 PF 1080 (2x) PS 1040 PT 04MCD 20164 2000 1600 400 SPM 2004 PF 1080 (2x) PS 1040 PT 04MCD 22106 2200 1000 600 SPM 2206 PF 1100 PS 1060 PT 06MCD 22126 2200 1200 600 SPM 2206 PF 1120 PS 1060 PT 06MCI 11066 1100 600 600 SPM 1106 PF 1060 PS 1060 PT 06MCI 14086 1400 800 600 SPM 1406 PF 1080 PS 1060 PT 06MCI 16066 1600 600 600 SPM 1606 PF 1060 PS 1060 PT 06MCI 18066 1800 600 600 SPM 1806 PF 1060 PS 1060 PT 06MCI 20066 2000 600 600 SPM 2006 PF 1060 PS 1060 PT 06MCI 20068 2000 600 800 SPM 2008 PF 1060 PS 1080 PT 08MCI 20086 2000 800 600 SPM 2006 PF 1080 PS 1060 PT 06MCI 20088 2000 800 800 SPM 2008 PF 1080 PS 1080 PT 08MCI 22066 2200 600 600 SPM 2206 PF 1060 PS 1060 PT 06MCI 22068 2200 600 800 SPM 2208 PF 1060 PS 1080 PT 08MCI 22086 2200 800 600 SPM 2206 PF 1080 PS 1060 PT 06MCI 22088 2200 800 800 SPM 2208 PF 1080 PS 1080 PT 08MCI 22089 2200 800 900 SPM 2209 PF 1080 PS 1090 PT 09MCS 18045 1800 400 500 SPM 1805 PF 1040 PS 1050 PT 05MCS 18064 1800 600 400 SPM 1804 PF 1060 PS 1040 PT 04MCS 18065 1800 600 500 SPM 1805 PF 1060 PS 1050 PT 05MCS 18084 1800 800 400 SPM 1804 PF 1080 PS 1040 PT 04MCS 18085 1800 800 500 SPM 1805 PF 1080 PS 1050 PT 05MCS 18104 1800 1000 400 SPM 1804 PF 1100 PS 1040 PT 04MCS 18105 1800 1000 500 SPM 1805 PF 1100 PS 1050 PT 05MCS 20044 2000 400 400 SPM 2004 PF 1040 PS 1040 PT 04MCS 20045 2000 400 500 SPM 2005 PF 1040 PS 1050 PT 05MCS 20046 2000 400 600 SPM 2006 PF 1040 PS 1060 PT 06MCS 20064 2000 600 400 SPM 2004 PF 1060 PS 1040 PT 04MCS 20065 2000 600 500 SPM 2006 PF 1060 PS 1050 PT 05MCS 20066 2000 600 600 SPM 2006 PF 1060 PS 1060 PT 06MCS 20068 2000 600 800 SPM 2008 PF 1060 PS 1080 PT 08MCS 20084 2000 800 400 SPM 2004 PF 1080 PS 1040 PT 04MCS 20085 2000 800 500 SPM 2005 PF 1080 PS 1050 PT 05MCS 20086 2000 800 600 SPM 2006 PF 1080 PS 1060 PT 06MCS 20088 2000 800 800 SPM 2008 PF 1080 PS 1080 PT 08MCS 20104 2000 1000 400 SPM 2004 PF 1100 PS 1040 PT 04MCS 20105 2000 1000 500 SPM 2005 PF 1100 PS 1050 PT 05MCS 20106 2000 1000 600 SPM 2006 PF 1100 PS 1060 PT 06MCS 22086 2200 800 600 SPM 2206 PF 1080 PS 1060 PT 06MCS 22088 2200 800 800 SPM 2208 PF 1080 PS 1080 PT 08MKD 16124 1600 1200 400 n/a PF 1120 PS 1040 PT 04MKD 18124 1800 1200 400 n/a PF 1120 PS 1040 PT 04MKD 18164 1800 1600 400 n/a PF 1080 (2x) PS 1040 PT 04MKD 20124 2000 1200 400 n/a PF 1120 PS 1040 PT 04MKD 20164 2000 1600 400 n/a PF 1080 (2x) PS 1040 PT 04MKS 16064 1600 600 400 n/a PF 1060 PS 1040 PT 04MKS 16084 1600 800 400 n/a PF 1080 PS 1040 PT 04MKS 16104 1600 1000 400 n/a PF 1100 PS 1040 PT 04MKS 18064 1800 600 400 n/a PF 1060 PS 1040 PT 04MKS 18084 1800 800 400 n/a PF 1080 PS 1040 PT 04MKS 18104 1800 1000 400 n/a PF 1100 PS 1040 PT 04MKS 20064 2000 600 400 n/a PF 1060 PS 1040 PT 04MKS 20084 2000 800 400 n/a PF 1080 PS 1040 PT 04MKS 20104 2000 1000 400 n/a PF 1100 PS 1040 PT 04
To order an enclosurewithout mounting plate,please add PE after thearticle code: e.g. MCS20086 PE.
* standard 100 mm, alsoavailable 200 mm high.Article code PS 2…and PF 2…
Explanation of the Eldon product coding:In order to make the change from theExcellence range to thenew Multi-Flex range aseasy as possible, justplace "M" in front of theenclosure coding (e.g. CS20086 =MCS 20086)
MCS 20086
M = Multi-Flex seriesC = combining versionS = single door (single)
200.. = 2000 mm high8. = 800 mm wide6 = 600 mm deep
MKD 18084
M = Multi-Flex seriesK = closed side panel (kompact)D = double door
180.. = 1800 mm high8. = 800 mm wide4 = 400 mm deep
MCI
I = ICT compatible, standarddelivered with 19" profiles
42 Multi-Flex Enclosures
43Multi-Flex Enclosures
Vent. plinth Cable Wide Filler Door drawing Ventilation 19" Separationfront/rear* assembly bars mounting plate plate desk roof profiles platePV 1080 CABP 800 MPF 1800 DDK 800 CVR 0805 CIP 38 SPD 1805PV 1100 CABP 1000 MPF 1800 CVR 1004 CIP 38 SPD 1804PV 1100 CABP 1000 MPF 1800 CVR 1005 CIP 38 SPD 1805PV 1120 CABP 1200 MPF 1800 DDK 600 (2x) CVR 1204 CIP 38 SPD 1804PV 1120 CABP 1200 MPF 1800 DDK 600 (2x) CVR 1205 CIP 38 SPD 1805PV 1080 (2x) CABP 800 (2x) MPF 1800 DDK 800 (2x) CIP 38 SPD 1804PV 1080 CABP 800 MPW 2008 MPF 2000 DDK 800 CVR 0805 CIP 42 SPD 2005PV 1100 CABP 1000 MPW 2010 MPF 2000 CVR 1004 CIP 42 SPD 2004PV 1100 CABP 1000 MPW 2010 MPF 2000 CVR 1005 CIP 42 SPD 2005PV 1100 CABP 1000 MPW 2010 MPF 2000 CVR 1006 CIP 42 SPD 2006PV 1100 CABP 1000 MPW 2010 MPF 2000 CVR 1008 CIP 42 SPD 2008PV 1120 CABP 1200 MPW 2012 MPF 2000 DDK 600 (2x) CVR 1204 CIP 42 SPD 2004PV 1120 CABP 1200 MPW 2012 MPF 2000 DDK 600 (2x) CVR 1205 CIP 42 SPD 2005PV 1120 CABP 1200 MPW 2012 MPF 2000 DDK 600 (2x) CVR 1206 CIP 42 SPD 2006PV 1120 CABP 1200 MPW 2012 MPF 2000 DDK 600 (2x) CVR 1208 CIP 42 SPD 2008PV 1080 (2x) CABP 800 (2x) MPF 2000 DDK 800 (2x) CIP 42 SPD 2004PV 1080 (2x) CABP 800 (2x) MPF 1800 DDK 800 (2x) CIP 38 SPD 1804PV 1080 (2x) CABP 800 (2x) MPF 2000 DDK 800 (2x) CIP 42 SPD 2004PV 1100 CABP 1000 MPW 2010 MPF 2200 CVR 1006 CIP 47 SPD 2206PV 1120 CABP 1200 MPW 2012 MPF 2200 DDK 600 (2x) CVR 1206 CIP 47 SPD 2206PV 1060 CABP 600 DDK 600 CVR 0606 CIP 22PV 1080 CABP 800 DDK 800 CVR 0806 CIP 29PV 1060 CABP 600 DDK 600 CVR 0606 CIP 33PV 1060 CABP 600 DDK 600 CVR 0606 CIP 38 SPD 1806PV 1060 CABP 600 DDK 600 CVR 0606 CIP 42 SPD 2006PV 1060 CABP 600 DDK 600 CVR 0608 CIP 42 SPD 2008PV 1080 CABP 800 DDK 800 CVR 0806 CIP 42 SPD 2006PV 1080 CABP 800 DDK 800 CVR 0808 CIP 42 SPD 2008PV 1060 CABP 600 DDK 600 CVR 0606 CIP 47 SPD 2206PV 1060 CABP 600 DDK 600 CVR 0608 CIP 47 SPD 2208PV 1080 CABP 800 DDK 800 CVR 0806 CIP 47 SPD 2206PV 1080 CABP 800 DDK 800 CVR 0808 CIP 47 SPD 2208PV 1080 CABP 800 MPF 2200 DDK 800 CVR 0809 CIP 47 SPD 2209PV 1040 CABP 400 MPF 1800 CIP 38 SPD 1805PV 1060 CABP 600 MPF 1800 DDK 600 CVR 0604 CIP 38 SPD 1804PV 1060 CABP 600 MPF 1800 DDK 600 CVR 0605 CIP 38 SPD 1805PV 1080 CABP 800 MPF 1800 DDK 800 CVR 0804 CIP 38 SPD 1804PV 1080 CABP 800 MPF 1800 DDK 800 CVR 0805 CIP 38 SPD 1805PV 1100 CABP 1000 MPF 1800 CVR 1004 CIP 38 SPD 1804PV 1100 CABP 1000 MPF 1800 CVR 1005 CIP 38 SPD 1805PV 1040 CABP 400 MPF 2000 CIP 42 SPD 2004PV 1040 CABP 400 MPF 2000 CIP 42 SPD 2005PV 1040 CABP 400 MPF 2000 CIP 42 SPD 2006PV 1060 CABP 600 MPW 2006 MPF 2000 DDK 600 CVR 0604 CIP 42 SPD 2004PV 1060 CABP 600 MPW 2006 MPF 2000 DDK 600 CVR 0605 CIP 42 SPD 2005PV 1060 CABP 600 MPW 2006 MPF 2000 DDK 600 CVR 0606 CIP 42 SPD 2006PV 1060 CABP 600 MPW 2006 MPF 2000 DDK 600 CVR 0608 CIP 42 SPD 2008PV 1080 CABP 800 MPW 2008 MPF 2000 DDK 800 CVR 0804 CIP 42 SPD 2004PV 1080 CABP 800 MPW 2008 MPF 2000 DDK 800 CVR 0805 CIP 42 SPD 2005PV 1080 CABP 800 MPW 2008 MPF 2000 DDK 800 CVR 0806 CIP 42 SPD 2006PV 1080 CABP 800 MPW 2008 MPF 2000 DDK 800 CVR 0808 CIP 42 SPD 2008PV 1100 CABP 1000 MPW 2010 MPF 2000 CVR 1004 CIP 42 SPD 2004PV 1100 CABP 1000 MPW 2010 MPF 2000 CVR 1005 CIP 42 SPD 2005PV 1100 CABP 1000 MPW 2010 MPF 2000 CVR 1006 CIP 42 SPD 2006PV 1080 CABP 800 MPF 2200 DDK 800 CVR 0806 CIP 47 SPD 2206PV 1080 CABP 800 MPF 2200 DDK 800 CVR 0808 CIP 47 SPD 2208PV 1120 CABP 1200 MPF 1600 DDK 600 (2x) CVR 1204PV 1120 CABP 1200 MPF 1800 DDK 600 (2x) CVR 1204 CIP 38PV 1080 (2x) CABP 800 (2x) MPF 1800 DDK 800 (2x) CIP 38PV 1120 CABP 1200 MPW 2012 MPF 2000 DDK 600 (2x) CVR 1204 CIP 42PV 1080 (2x) CABP 800 (2x) MPF 2000 DDK 800 (2x) CIP 42PV 1060 CABP 600 MPF 1600 DDK 600 CVR 0604 CIP 33PV 1080 CABP 800 MPF 1600 DDK 800 CVR 0804 CIP 33PV 1100 CABP 1000 MPF 1600 CVR 1004 CIP 33PV 1060 CABP 600 MPF 1800 DDK 600 CVR 0604 CIP 38PV 1080 CABP 800 MPF 1800 DDK 800 CVR 0804 CIP 38PV 1100 CABP 1000 MPF 1800 CVR 1004 CIP 38PV 1060 CABP 600 MPW 2006 MPF 2000 DDK 600 CVR 0604 CIP 42PV 1080 CABP 800 MPW 2008 MPF 2000 DDK 800 CVR 0804 CIP 42PV 1100 CABP 1000 MPW 2010 MPF 2000 CVR 1004 CIP 42
44 Multi-Flex Enclosures
Accessories
Side mounting bar, CMB
For fixing cables, cable guides, etc. in the side of an enclosure.Material: 2 mm zinc plated steel.Pack quantity: 10 profiles with mounting material.
For enclosure:W D Cat.no.400 400 CMB 400
500 CMB 500600 600 CMB 600800 800 CMB 800
Click-in profile, CLCK
Universal for both depth and width fitting on the 25 mm DIN hole pat-tern of the enclosure frame. Can be secured by the use of self-tappingscrews. Material: 1.5 mm zinc plated steel. Pack quantity: 4 profiles.
For enclosure:W D w d Cat.no.400 400 335 335 CLCK 400500 500 435 435 CLCK 500600 400 535 335 CLCK 600800 800 735 735 CLCK 800Cage nuts, CNM
Cage nuts M 6 designed for universal use on the enclosure frame pro-files and the profile system.Pack quantity: 50 pcs. Thread Cat.no.
M6 CNM 615M6 CNM 620M8 CNM 815M8 CNM 820
Countersunk screws, CNK
Torx countersunk screws M6 x 16Pack quantity: 250 pieces
Cat.no.CNK 06
Clip-on cagenuts, CNN
Clip-on M6 cagenut for fixing side panels.Pack quantity: 50 pieces
Carrier bars, CB
Used for heavy units, such as transformers, fitted in the bottom of theenclosure.Material: 3 mm zinc plated steel. Pack quantity: 2 bars with mounting material.
W D Cat.no.400 400 CB 400
500 CB 500600 600 CB 600800 800 CB 800
Extrudetite screws, CNT
Torx extrudetite screws for the fitting of accessories, click in profiles,earthing etc.Pack quantity: 250 pieces
Thread Cat.no.M5 CNT 05M6 CNT 06
Screws for cage nuts, CNS
Socket head screws M6x12 for cage nutsPack quantity: 250 pieces
Thread Cat.no.M6 CNS 612
Thread Cat.no.M6 CNN 615
45Multi-Flex Enclosures
Accessories
Height profiles, HP
Vertical profiles with 25 mm hole pattern, to support DIN rails andappropriate telequick mounting plates. Adjustable in depth in steps of25 mm. Material: 2 mm zinc plated steel.Pack quantity: 2 profiles with mounting material
H Cat.no.1600 HP 16001800 HP 18002000 HP 20002200 HP 2200
Cable fixing bar, CAB
Mounted above the bottom plates. Holds standard cable clamps CACto secure incoming cables. Adjustable in depth.Material: 2 mm zinc plated steel. Pack quantity: 2 bars with mounting material.
For enclosure:W Cat.no.
400 CAB 400600 CAB 600800 CAB 800
1000 CAB 10001200 CAB 1200
Cable fixing bar, CABP
Suspended below the bottom plates thereby maximising the full usablespace in the enclosure. Holds standard cable clamps CAC to secureincoming cables. Adjustable in depth.Material: 2 mm zinc plated steel. Pack quantity: 2 bars with mounting material.
W Cat.no.400 CABP 400600 CABP 600800 CABP 800
1000 CABP 10001200 CABP 1200
Cable clamps, CAC
To secure incoming cables onto the fixing bars CAB and CABP. Holdsthe cable in position and supports the weight.Material: Zinc plated steel.Pack quantity: 25 clamps
Size Cat.no.6-14 mm CAC 0614
12-18 mm CAC 121818-22 mm CAC 182222-26 mm CAC 222626-30 mm CAC 263030-34 mm CAC 303434-38 mm CAC 343838-42 mm CAC 384242-46 mm CAC 4246
Mounting angle (19”) for asymmetricfixing profile, CID
For fitting asymmetric 482,6 mm mounting angles (19”) in 800 mm orwider enclosures. Fully adjustable in depth. Material: 3 mm zinc plated steel.Pack quantity: 4 profiles with mounting material
D Cat.no.600 CID 600800 CID 800
46 Multi-Flex Enclosures
Accessories
Mounting angles (19”), CIP
Full height mounting angles to achieve 482.6 mm (19”) mounting requi-rements on all sides. Fully adjustable in depth. To be used in conjunc-tion with CIB and CIBP brackets. Material: 2 mm zinc plated steel, Pack quantity: 2 pieces with mounting material.
H U Cat.no.1100 22 CIP 221400 29 CIP 291600 33 CIP 331800 38 CIP 382000 42 CIP 422200 47 CIP 47
Mounting angles (19”) partial height, CIPP
Partial height mounting angles to achieve 482.6 mm (19”) mountingrequirements on all sides. Fully adjustable in depth. To be used in com-bination with CLCK profiles. For 800 mm wide enclosures add CICbrackets. Material: 2 mm zinc plated. Pack quantity: 2 pieces with mounting material.
U Cat.no.6 CIPP 069 CIPP 09
10 CIPP 1011 CIPP 1113 CIPP 1315 CIPP 1518 CIPP 1821 CIPP 2127 CIPP 27
Brackets for fixing 19” mounting angles, CIB
For fitting 482,6 mm full height mounting angles (19”) in 600 & 800 mmwide enclosures. Fully adjustable in depth. Material: 3 mm zinc plated steel.Pack quantity: 2 profiles with mounting material
W D Cat.no.600 600 CIB 600800 800 CIB 800
Mounting profiles, CIPD
Side universal 19” punchings. For additional internal support. To beused in conjunction with CIB profiles.Material: 2.0 mm zink plated steel plate.Pack. quantity: 1 pair
Cat.no.CIPD 33CIPD 38CIPD 42CIPD 47
47Multi-Flex Enclosures
Accessories
Baying kit for Excellence to Multi-Flex, CCC
Brackets to bay the Excellence enclosure to the Multi-Flex enclosure.With “auto spacer” function.Material: 3 mm zinc plated steel.Pack quantity: 6 brackets with mounting material.
Cat.no.CCC 06
Internal combining kit, CCJ
For baying enclosures. To be used when separation or marshallingplates are fitted.Material: 3 mm zinc plated steel. Pack quantity: 12 brackets with mounting material.
Cat.no.CCJ 6
Internal corner combining kit, CCM
For extra support when bayed enclosures are fully equipped and requi-re heavy duty lifting.Material: 3 mm zinc plated steel. Pack quantity: 4 brackets with mounting material.
Cat.no.CCM 08
Lütze system adaptor profile, CLS
Adapter to fix the Lütze system direct to the Multi-Flex enclosure frame.Adjustable in depth by steps of 25 mm. The width of the Lütze frameequals the enclosure nominal width minus 22 mm.Material: 2.5 mm zinc plated steel. Pack quantity: 6 adapter bars with mounting material.
W D Cat.no.600 600 CLS 600800 800 CLS 800
Brackets for partial height mounting angles(19”), CIC
For fixing 482,6 mm partial height mounting angles (19”) in 800 mmwide enclosures. Adjustable in depth in steps of 12.5 mm, by using theCLCK click-in profiles. Material: 3 mm zinc plated steel.Pack quantity: 4 brackets with mounting material.
Cat.no.CIC 04
External baying brackets, CCE
Brackets mounted on the outside hole pattern of the frame ensuring astrong & 3 dimensional alignment of the bayed enclosures with “autospacer” function. This method of baying enclosures has also theadvantage of realising a direct earthing connection between the enclo-sure frames.Material: 3 mm zinc plated steel.Pack quantity: 6 brackets with mounting material.
Cat.no.CCE 6
48 Multi-Flex Enclosures
Accessories
Internal baying brackets, CCI
Brackets provide a rigid reinforcement of the enclosure assembly.Automatic spacing between the enclosures is ensured.Material: 3 mm zinc plated steel. Pack quantity: 6 brackets with mounting material.
Cat.no.CCI 6
Internal baying kit, CCCS
Internal conversion kit Excellence enclosures to Multi-Flex enclosures.
Cat.no.CCCS 06
Partial height mounting plate, MPP
Mounted directly on the enclosure frame or onto the click-in profiles(CLCK). Special design of the bracket allows one man mounting. Canbe mounted in any height or depth position within the 25 mm hole pat-tern. Appropriate sizes can also be used in the sides of the enclosure.Material: 3 mm galvanised steel.Pack quantity: 1 plate with mounting material
H W h w Cat.no.400 400 294 294 MPP 0404
500 294 394 MPP 0405600 400 494 294 MPP 0604
500 494 394 MPP 0605800 494 694 MPP 0608
1000 494 894 MPP 0610800 400 694 294 MPP 0804
800 694 694 MPP 08081000 400 894 294 MPP 1004
800 894 694 MPP 10081200 400 1094 294 MPP 1204
600 1094 494 MPP 1206
Transversal sliding profiles, MTS
To be used when installing a wide mounting plate. Adjustable in depthin steps of 25 mm.Material: 2 mm galvanised steel.Pack quantity: 2 profiles with mounting material.
For enclosure:W Cat.no.
600 MTS 06800 MTS 08
1000 MTS 101200 MTS 12
49Multi-Flex Enclosures
Accessories
Mounting plates, MP
Standard mounting plate. Fixing bracket kit MPA 06 to be orderedseparately.Material: 3 mm galvanised steel.Pack quantity: 1 piece
H W h w Cat.no.1600 600 1494 494 MP 1606
800 1494 694 MP 16081000 1494 894 MP 16101200 1494 1094 MP 1612
1800 600 1694 494 MP 1806800 1694 694 MP 1808
1000 1694 894 MP 18101200 1694 1094 MP 1812
2000 600 1894 494 MP 2006800 1894 694 MP 2008
1000 1894 894 MP 20101200 1894 1094 MP 2012
2200 600 2094 494 MP 2206800 2094 694 MP 2208
1000 2094 894 MP 22101200 2094 1094 MP 2212
Wide mounting plate, MPW
To be mounted on sliding profiles MTS. Nominal width equals theenclosure width.Material: 3 mm galvanised steel.Pack quantity: 1 piece with mounting material
H W Cat.no.2000 600 MPW 2006
800 MPW 20081000 MPW 20101200 MPW 2012
Telequick Mounting plate, MT
Simplifies installation and equipment fitting. Rectangular holes 26 x11 mm to obtain required fixing positions with snap-nuts. The nuts canbe moved around within the rectangular hole.Material: 2 mm galvanised steel.
H W Cat.no.250 250 MT 02525300 300 MT 03030400 300 MT 04030
400 MT 04040500 400 MT 05040600 400 MT 06040
500 MT 06050600 MT 06060
800 600 MT 080601000 600 MT 10060
800 MT 10080
Side mounting plate brackets, MPS
To mount the standard mounting plate in the side of the enclosureframe. Provides a flat mounting surface with the profiles. Material: 3 mm galvanised steel.Pack quantity: 4 brackets with mounting material.
Cat.no.MPS 04
50 Multi-Flex Enclosures
Accessories
Filler plates, MPF
Covers the space between pairs of adjacent mounting plates to provi-de a continuous working surface, when two enclosures are mountedtogether.Material: 2 mm galvanised steel. Pack quantity: 1 plate with mounting material.
H Cat.no.1800 MPF 18002000 MPF 20002200 MPF 2200
Mounting plate brackets, MPA
To fix mounting plates to the furthest position in the rear of the enclo-sure, including adjustment brackets for depth adjustment in steps of25 mm.Material: 3 mm zinc plated steel. Pack quantity: 2 top brackets and 2 bottom sliding brackets, 2 adjust-ment brackets with mounting material.
Cat.no.MPA 06
Separation plates, SPD
Separates two bayed enclosures. To be fixed with combining kit CCJ.To achieve IP 55 a neoprene gasket SPDG 01 can be fixed to the panel. Material: 1,5 mm galvanised steel. Pack quantity: 1 piece
H W Cat.no.1800 400 SPD 1804
500 SPD 18052000 400 SPD 2004
500 SPD 2005600 SPD 2006800 SPD 2008
2200 600 SPD 2206800 SPD 2208
Mounting plate adjustment brackets, MPD
Cat.no.MPD 02
With these brackets the mounting plate can be fixed in depth by stepsof 25 mm in the enclosure frame.Material: 3 mm zinc plated steel. Pack quantity: 2 brackets with mounting material.
Gasket for EMC shielding, SPDE
Cat.no.SPDE 01
Separation plate gasket, SPDG
To obtain IP 55/NEMA 12 sealing in combination with the separationplate SPD.
Cat.no.SPDG 01
To obtain an EMC shielded section in a suited panel in combination withthe separation plate SPD. Protection: IP 54/NEMA 1
Mounting plate fixing bracket, MPE
For extra fixing of the mounting plate in the middle in addition to thenormal fixing top and bottom.
Cat.no.MPE 02
51Multi-Flex Enclosures
Accessories
Side panels, SPM
Easy one man assembly. Sealed by an extruded, one piece polyure-thane gasket and mounted with 8 screws. Material: 1.5 mm steel plate.Finish: structure powder paint, RAL 7032Pack quantity: 2 panels with mounting material.
H D Cat.no.1100 600 SPM 11061400 600 SPM 14061600 600 SPM 16061800 400 SPM 1804
500 SPM 1805600 SPM 1806
2000 400 SPM 2004500 SPM 2005600 SPM 2006800 SPM 2008
2200 600 SPM 2206800 SPM 2208900 SPM 2209
Earthing connection for panels, ECP
Earth connection for the fixing of the earthing straps & cables to panels,mounting plates or profiles.Pack quantity: 20 sets.
Size Cat.no.M6 ECP 06M8 ECP 08
Internal combining kit, CCJ
For baying enclosures. To be used when separation or marshallingplates are fitted.Material: 3 mm zinc plated steel. Pack quantity: 12 brackets with mounting material.
Cat.no.CCJ 6
Earthing strap, ECFE
For earthing or potential compensation between panels and enclosureframe.Material: Tinned electrolytic copper wires with solder connectionpoints.Length: 300 mm.Pack quantity: 10 pieces.
Cross sectional Holes Strap area diam. width Cat.no.
16 mm2 8.5 15 ECFE 163025 mm2 10.5 23 ECFE 2530
52 Multi-Flex Enclosures
Accessories
Plain doors, D
Standard door equipped with DIN 3 mm lock system and doorframe.Door accessory kit DMK (hinges, rod catchers) to be ordered separa-tely. Allows all the options of the locking program and 180° hinges. Material: 2 mm steel plateFinish: structure powder paint, RAL 7032.Pack quantity: 1 piece
H W Cat.no.1100 600 D 11061400 800 D 14081600 600 D 16061800 600 D 1806
800 D 18082000 600 D 2006
800 D 20082200 600 D 2206
800 D 2208
Glazed door, DGC
Standard door with fitted clear safety glass to view the inside of theenclosure. Allows all options of the locking program. Use hinge kit DMKif not for replacement of standard door.Protection: IP 55. Material: Frame: 2 mm steel plate. Viewing area: 4 mm hardened clearglassFinish: structure powder paint, RAL 7032Pack quantity: 1 piece
Clear glassH W Cat.no.
1100 600 DGC 11061400 800 DGC 14081600 600 DGC 16061800 600 DGC 1806
800 DGC 18082000 600 DGC 2006
800 DGC 20082200 600 DGC 2206
800 DGC 2208
Smoked glassH W Cat.no.
1100 600 DGS 11061400 800 DGS 14081600 600 DGS 16061800 600 DGS 1806
800 DGS 18082000 600 DGS 2006
800 DGS 20082200 600 DGS 2206
800 DGS 2208
53Multi-Flex Enclosures
Accessories
Door mounting kit, DMK
Required when fitting a door to the rear of an enclosure. Pack quantity: 1 kit of 4 standard hinges, 4 rod catchers and mountingmaterial
Cat.no.DMK 01
Inner door, DI
Mounted on vertical plates, which prevent access on the sides. Theinner door provides a hinged mounting surface for equipment behind astandard or glazed front door. A mounting space of 80 mm is availablebetween the doors when the inner door is in forward position. The innerdoor can be adjusted in the depth by steps of 25 mm.The mountingplate remains usable behind the inner door.The door is equipped with two locks, 3 mm DIN, and plastic handles.Material:1.5 mm steel plate, powder structure paint, RAL 7032.Pack quantity: 1 door with mounting material
H W Cat.no.1800 600 DI 1806
800 DI 18082000 600 DI 2006
800 DI 2008
Door hinges 180°, DH
Door hinges 180°Enables the door to open 180 degrees, even when enclosures arebayed together. Material: Die-cast zinc. Finish: Blue.Pack quantity: 4 hinges with mounting material.
Cat.no.DH 180
Front frame cover, FFC
To cover the framework around the door aperture on a 600 wide data-telecom enclosures, when a door is not fitted. Material: 2 mm steel plate. Finish: structure powder paint, RAL 7032.Pack quantity: 1 set with mounting material
H W Cat.no.2000 600 FFC 20062200 600 FFC 2206
54 Multi-Flex Enclosures
Accessories
Door frame mounting profiles, DCP
Horizontal assembly bars type CP 2020 with 25 mmhole pattern. Fit directly onto door frame. For easy mounting of lightequipment, using sliding nuts GLM 20-6, cables routing etc.Material: 1.5 mm zinc plated steel. Pack quantity: 2 bars with mounting material.
W Cat.no.400 DCP 400500 DCP 500600 DCP 600800 DCP 800
1000 DCP 1000
Door stop, DSTP
To lock a open door in position. Mounted directly to the doorframe andinto the enclosure profile thereby the full mounting area of the frame iskept free. Material: zinc plated steelPack quantity: 1 piece with mounting material.
Cat.no.DSTP 01
Door switch, DSW
Activates any electrical device (lighting, coolers, etc.). Can be fitted afterinstalling the enclosure thereby keeping the door opening free. Fixed(without screws) on the inside hole pattern of the enclosure frame.Cable entry M 20, UL-CSA approved.Switching load 6A-230V.Pack quantity: 1 piece with mounting material
Cat.no.DSW 01
55Multi-Flex Enclosures
Accessories
Inserts, LSI
Inserts without cover
Description Cat.no.3 mm DIN LSI 5035 mm DIN LSI 505Square 7 mm LSI 523Square 8 mm LSI 524Triangle 7 mm LSI 526Triangle 8 mm LSI 527Daimler Benz LSI 530
Keys, LSK
Description Cat.no.DIN 3 mm LSK 503DIN 5 mm LSK 505Square 7 mm LSK 523Square 8 mm LSK 524Triangle 7 mm LSK 526Triangle 8 mm LSK 527
Swing handles, LSS
Swinghandles with inserts type:
Description Cat.no.profile half cylinder Ronis key nr. C21323 LSS 521round cylinder Ronis key nr. C21323 LSS 522square 7 mm LSS 523square 8 mm LSS 524triangle 6,5, CNOMO LSS 525triangle 7 mm LSS 526triangle 8 mm LSS 527DIN 3 mm LSS 528DIN 5 mm LSS 529Daimler Benz LSS 530slotted 2x4 mm deep LSS 531push button with round cylinder, key nr. C2233 LSS 532cylinder key nr. E1 (VW) LSS 533adapter for other profile hallf cylinders (DIN 18252) LSS 534adapter for Abloy Assa and Trioving cylinders LSS 535push button only LSS 536with transponder LSS 537with key pad LSS 538with finger print LSS 539with mobile phone locking LSS 540with laptop locking LSS 541with insert square 7 mm and Padlock facility (Ford) LSS 570
T-handles, LST
T-handles
Description Cat.no.with Ronis cylinder key nr. C21323* LST 560without cylinder LST 560 CEwith Ronis cylinder key nr. 2132E LST 560 2132Ewith Ronis cylinder key nr. 3121E LST 560 3121Ewith Ronis cylinder key nr. 3524E LST 560 3524E* other key numbers available on request
Lock cover, LSC Lock cover for inserts
Cat.no.LSC 500
56 Multi-Flex Enclosures
Accessories
Cooling door, DTF
Standard door with integrated heat exchanger to be fitted to the Multi-Flex MCS and MKS series. Attractive “low profile” design, that bleedsin harmoniously with any machine or system. Optimum cooling by vir-tue of extremely long passage of air in the inner airflow circuit.Aluminum and stainless steel chassis. Reliability under even the mostextreme conditions, since the electronics in the cooling unit are locatedin the cooling circuit. Power indicator light on the front. Use hinge kitDMK if used in front of frame without door. Equipped with DIN 3 mmlock system.Protection: IP 54 against the enclosure, IP 34 against the ambience(IEC 60529), when used as recommended.Material: Door 2 mm and cooler cover 1.5 mm steel plate. Finish: structure powder paint, RAL 7032Pack quantity: 1 pieceStandard UL and cUL approved.
H W Watt Cat.no.1800 600 1000 DTF 180610
1500 DTF 1806152000 DTF 1806202500 DTF 180625
800 1000 DTF 1808101500 DTF 1808152000 DTF 1808202500 DTF 180825
2000 600 1000 DTF 2006102000 600 1500 DTF 200615
2000 DTF 2006202500 DTF 200625
800 1000 DTF 2008101500 DTF 2008152000 DTF 2008202500 DTF 200825
Ventilation roof, CVR
Raised roof with 2.5 mm ventilation slots and filter material. Increasesthe enclosure height by 40 mm. IP 31 and NEMA 1Temperature resistance: 100°C.Material: 1.5 mm steel plate. Finish: structure powder paint RAL 7032.Filter material: EU 4 according to DIN 24185.Pack quantity: 1 piece with mounting brackets and ventilation filter.
W D Cat.no.600 400 CVR 0604
500 CVR 0605600 CVR 0606800 CVR 0608
800 400 CVR 0804500 CVR 0805600 CVR 0806800 CVR 0808900 CVR 0809
1000 400 CVR 1004500 CVR 1005600 CVR 1006800 CVR 1008
1200 400 CVR 1204500 CVR 1205600 CVR 1206800 CVR 1208
57Multi-Flex Enclosures
Accessories
Top cover with cable brush openings, CRB
For cable entry on three sides. Openings provided with brushes.Material: 1.5 mm steel plate.Finish: Structure powder paint, RAL 7032.Pack quantity: 1 piece with brushes and mounting material
W D Cat.no.600 600 CRB 0606
800 CRB 0608800 600 CRB 0806
800 CRB 0808900 CRB 0809
Top cover with cable gland opening, CRG
For cable entry. Material: 1.5 mm steel plate.Finish: Structure powder paint, RAL 7032.Pack quantity: 1 piece with gland plates, gaskets and mounting mate-rial.
D W Cat.no.600 600 CRG 0606
800 CRG 0608800 600 CRG 0806
800 CRG 0808900 CRG 0809
Roof exhaust unit, REU
Ventilation unit for mounting on the top of the enclosure providing natu-ral ventilation i.e. without a fan. A sealing gasket to assure an IP 33 pro-tection is supplied. By the addition of the exhaust unit filter kit REUF, anIP 43/NEMA 1 can be achieved.Material: 1.5 mm steel. Finish: structure powder paint RAL 7032. Pack quantity: 1 exhaust unit with mounting material and installationtemplate.
Cat.no.REU 01
Exhaust unit filter kit, REUF
For the roof exhaust unit REU, to achieve an IP 43.Pack quantity: 3 pieces.
Cat.no.REUF 01
Fan roof plates, CFR
For mounting a combination of 6 fans DFN 02 or closing plates DFC01for unused holes in the top of the enclosure. To be used in combinationwith the ventilated roof plate CVR. Material: 2 mm zinc plated steel.Pack quantity: 1 piece with mounting material
W D Cat.no.600 600 CFR 0606
800 CFR 0608800 600 CFR 0806
800 CFR 0808900 CFR 0809
Roof ventilation unit, RVU
Ventilation unit for mounting on top of the enclosure, providing high airflow and low noise level by the use of a centrifugal fan. Provided withsealing gasket to assure an IP 33/NEMA 1 protection. Free airflow 450m3/h.Noise level: 61 dB (A). Maximum temperature: 50 °C. Standard ULapproved.Material: 1.5 mm steel plate.Finish: Structure powder paint RAL 7032.Pack quantity: 1 fan unit with connection cable, mounting material andinstallation template.
Description Cat.no.230 /VAC 50-60 Hz RVU 480115 /VAC 50-60 Hz RVU 481
58 Multi-Flex Enclosures
Accessories
Cable entry foam and bottom plate gasket, BG
The bottom of the enclosure is sealed by the use of an adhesive gas-ket applied on to the frame around the bottom openings. The cablesare sealed by the addition of adhesive foam placed between the bot-tom plates. The elasticity and the size of this foam assure a tight sealaround most cables.Pack quantity: 1.6 m adhesive foam (30 x 25 mm) and 6 m adhesivegasket (4.5 x 8 mm).
Cat.no.BG 01
EMC cable entry and bottom plate gasket, BGE
The bottom of the enclosure is sealed by the use of an adhesive gas-ket applied to the frame around the bottom opening. The cables aresealed by the addition of adhesive foam placed between the bottomplates. The elasticity and the size of this foam assure a tight seal aroundmost cables.Pack quantity: 1.6 m adhesive EMC gasket for cable entry and 6 madhesive bottom plate gasket.
Cat.no.BGE 01
Ventilated bottom plates, CVB
Three piece bottom plates. Can be used in combination with a ventila-ted plinth PV.Material: 1.5 mm perforated zinc plated steel.Pack quantity: 3 pieces with mounting material.
W D Cat.no.600 600 CVB 0606
800 CVB 0608800 600 CVB 0806
800 CVB 0808900 CVB 0809
59Multi-Flex Enclosures
Accessories
Plinths, front/rear, PF
For cabling without any restrictions and in accordance with the VDE0113 standard. The plinth consists of four corner pieces with remo-vable front covers. The side panels PS are to be ordered separately.Produced in 100 mm and 200 mm heights.200 mm high plinths are delivered with a rear cover for cabling thatconsists of two removable panels 100 mm high. The front cover is aone piece panel of 200 mm high. All panels have double returns oneach panel.Materials: corner pieces in 2,5 mm ZINC plated steel, panels in 2 mmsteelplate.Finish: structure powder paint, RAL 7022Pack quantity: 1 set of 4 corner pieces including covers, 1 front and 1rear panel (2 rear panels for 200 mm high plinths) with mounting mate-rial for side panels and transversal profiles.
H W Cat.no.100 400 PF 1040
600 PF 1060800 PF 1080
1000 PF 11001200 PF 1120
200 400 PF 2040600 PF 2060800 PF 2080
1000 PF 21001200 PF 2120
Plinth side panels, PS
Side panels to cover the openings in the depth of the PF plinth. Doublebended panels for maximum strength available in 100 mm and 200 mmheight. Material: 2 mm steel plate. Finish: structure powder paint, RAL 7022Pack quantity: 2 panels. Mounting material included with PF.
H D Cat.no.100 400 PS 1040
500 PS 1050600 PS 1060800 PS 1080900 PS 1090
200 400 PS 2040500 PS 2050600 PS 2060800 PS 2080900 PS 2090
Plinth transversal profiles, PT
Acts as a stabiliser when cabling between bayed enclosures and fullplinth side panels obstruct the cable routing. Material: 2 mm steel plate.Finish: structure powder paint, RAL 7022Pack quantity: 2 profiles. Mounting material included with PF.
D Cat.no.400 PT 04500 PT 05600 PT 06800 PT 08
Ventilated plinth with panels, PV
Front and rear plinth sections with ventilated panels.Can be used in combination with the ventilated bottom plate CVB.Materials: corner pieces in 2,5 mm ZINC plated steel, panels in 2 mmsteel plate.Finish: structure powder paint, RAL 7022Pack quantity: 2 panels with mounting material
W Cat.no.600 PV 1060800 PV 1080
1000 PV 1100
60 Multi-Flex Enclosures
Accessories
Horizontal divider, CDH
Used when the enclosure requires separation by partial doors orpanels. Can be mounted on the outside hole pattern of the C versionor inside hole pattern of the K version..Material: 2 mm steel plate.Finish: Structure powder paint RAL 7032. Pack quantity: 4 profiles with mounting material.
W Cat.no.400 CDH 400600 CDH 600800 CDH 800
Cable Conduit, CONU
For flexible and safe protection of cables installed between the door orswing frame and the enclosure interior.Highly flexible and halogen free.Material: Polyamide, UL approved.Pack quantity: 25 m.* Available only on request.
Diameter Cat.no.16 CONU 1629 CONU 2936 CONU 3648 CONU 48
Cable conduit, CON
For flexible and safe protection of cables installed between the door orswing frame and the enclosure interior.Highly flexible and halogen free.Material: Polyethylene.Pack quantity: 25 m.
Diameter Cat.no.16 CON 1629 CON 2936 CON 3648 CON 48
Universal conduit holder, CONH
Universal holder for cable conduit CON. Can be mounted horizontallyor vertically on any 25 mm hole pattern of door frame, enclosure frameor accessory profile.Material: Polycarbonate.Pack quantity: 10 pcs.
Holes diam. Cat.no.
16 CONH 1629 CONH 2936 CONH 3648 CONH 48
61Multi-Flex Enclosures
Accessories
Drawing desk, DDK
Mounted directly to the doorframe and it provides a stable surface fordocuments, computer or measuring devices. The desk can be easilyfolded and locked within the doorframe space. An automatic safetypositioning system locks the desk at angles of 55, 70 and 90 degrees.The DDK 800 can also be mounted on a 1000 mm wide door, by theuse of the DCP 1000 accessory.Material: 1.5 mm steel plate. Finish: structure powder paint, RAL 7032.Pack quantity: 1 piece with mounting material
W Cat.no.600 DDK 600800 DDK 800
Drawing pocket, DRB
A large steeel document pocket fixed directly onto the door frame. Usable depth: 68 mm.Material: 1.5 mm steel plate.Finish: structure powder paint, RAL 7032. Pack quantity: 1 piece with mounting material.
W Cat.no.1000 (double door x 2) DRB 500600 DRB 600800 DRB 800
1000 DRB 1000
Document pocket, DRA
Self adhesive, for DIN A4 format. Usable depth: 30 mm.Colour: greyMaterial: Thermoplastic
Cat.no.DRA 04
Lifting device, LC
For optimal weight distribution when lifting bayed enclosures. To beused in combination with CCM bracket.Material: 5 mm zinc plated steel. Pack quantity: 4 pieces with mounting material
Cat.no.LC 12
62 Multi-Flex Enclosures
Accessories
Lifting eye bolts, LE
M12 thread. Complies with DIN 580 lifting requirements.Pack quantity: 2 pieces.
Cat.no.LE 9301
Ventilated shelf, SHC
Mounted directly to enclosure frame. The load carrying capacity is50 kg. Material: 2 mm steel plate. Finish: structure powder paint RAL 7032.Pack quantity: 1 shelf with mounting material.
W D w d Cat.no.600 600 509 560 SHC 0606
800 509 760 SHC 0608800 600 709 560 SHC 0806
800 709 760 SHC 0808900 709 860 SHC 0809
Monitor shelf, SHM
Mounted directly on to the enclosure frame. Provided with clamp-kit tohold the monitor in position. Material: 2 mm steel plate. Finish: structure powder paint RAL 7032. Pack quantity: 1 piece with mounting material.
W D Cat.no.600 600 SHM 0606
800 SHM 0608
Telescopic ventilated shelf, SHT
Mounted directly to enclosure frame. The load carrying capacity is50 kg. Material: 2 mm steel plate.Finish: structure powder paint RAL 7032.Pack quantity: 1 shelf and 1 pair of 3 member slides with mountingmaterial.
W D Cat.no.600 600 SHT 0606
800 SHT 0608800 600 SHT 0806
800 SHT 0808
63Multi-Flex Enclosures
Accessories
Wall fixing brackets, CCB
Roof mounting. Pack quantity: 2 pieces
Cat.no.CCB 02
* Available on request
Spacer kit, CVK
Provides ventilation by raising the roof panel 15 mm. Material: Zinc plated steelPack quantity: 4 pieces with mounting material
Cat.no.CVK 15
Door wheel, DSR
To ease heavy loaded doors into position. Mounted directly onto thedoor frame.Pack. quantity: 5 pieces
Cat.no.DSR 2005DSR 2006
Castors, LCR
For easy moving of the enclosure. To be mounted to the frame by brac-kets.Maximum load: 240 kg. Raises the enclosure by 70 mm. Pack quanti-ty: 4 pieces with mounting material..
H Cat.no.70 LCR 470
64 Multi-Flex Enclosures
Accessories
Levelling feet, LF
Adjustable feet for the leveling of enclosures placed on uneven ground.Mounted directly to the frame. Maximum load: 300 kg per foot.Adjustment stroke = 30 mm. Pack quantity: 4 pieces
Cat.no.LF 430
Cover plates, MMG
To cover unused connector cut-outs of a marshalling plate mm or asadapter for 16 pins connectors to allow the mix of both type of connec-tors.Material: 2 mm galvanized steel.Pack quantity: including mounting material and seal.
Pack quant. Cat.no.
1 MMG 04165 MMG 2416
20 MMG 1620 MMG 241 MMG 4024
Connector plate between two enclosures, or to be used in combinationwith a raised side door (DSR). Hole patterns for 16 pin or 24 pinconnectors. To be mounted with CCJ 12 bracket set. Material: 2 mm galvanized steelPack quantity: 1 piece
H W Cat.no.1800 500 MM 1805
600 MM 18062000 500 MM 2005
600 MM 2006
Marshalling plates, MM
Mains leads, CLF
Cable (3 x 1.5 mm2) with female GST 18/3 connector at one end for theconnection to mains power. Length: 3 m.Pack quantity: 5 pieces.
Cat.no.CLF 3005
Connection leads, CLM
Cable (3 x 1.5 mm2) with male GST 18/3 connector at one end for theconnection to power outlet of any device or further enclosure circuit.Length: 1 m.Pack quantity: 5 pieces.
Cat.no.CLM 1005
65Multi-Flex Enclosures