excellance, inc. - ohioprocure.ohio.gov/pricelist/800579pricelist.pdf · 2017. 8. 22. · ohio...

Ohio State Term Schedule Price List EXCELLANCE, INC.

453 Lanier Road, Madison, AL 35758

1.800.882.9799 www.excellanceinc.com

EXCELLANCE, INC.

Manufacturers of Quality Emergency Medical/Rescue Vehicles

PAGE

344456678889

1011131318192122222222232325252627

115 VAC Electrical Equipment OptionsScene and Exterior Light Standard Specifications

115/120 VAC Electrical Standard SpecificationsShoreline Options

Exterior Compartment OptionsPatient Compartment Standard SpecificationsPatient Compartment OptionsBio-Hazard/Trash storageSeating/Upholstery OptionsFloor Covering Options

TABLE OF CONTENTS

CONTENTS

Base Model Ambulance PricingMultiple unit order discountChassis

Chassis Electrical System Standard SpecificationsChassis Electrical System Interior Cab OptionsModular Body Standard SpecificationsModular Body OptionsCab/Module Paint and graphicsExterior Compartments Standard Specifications

Chassis Special OptionsChassis Air Ride & Suspension OptionsChassis Tire/Wheel OptionsChassis Air Horn OptionsChassis Exterior OptionsChassis Interior Cab Options

Handrails/Mounting Bracket OptionsCot/ Litter OptionsModule Electrical System Standard SpecificationsModule Electrical System Options

Effective: 6/9/17 Excellance - OH STS 2017 / 2018 Price List Page 1




27282828

292930313131

Oxygen System Options 32Medical Air System Options 32Vacuum System Options 33HVAC System Standard Specifications and Options 33Fire Extinguisher Options 35Customer Supplied Parts Policy 35Customer / Dealer Supplied Chassis Policy 35

Emergency Light OptionsMiscellaneous Warning Light OptionsEmergency Audible Warning System OptionsOxygen and Suction System Standard SpecificationsOxygen Tank Bracket Options

Worklights/Floodlights/Spotlight OptionsTurn signal/tail light OptionsEmergency Visual Warning System OptionsFront Light Bar Options

Rear Light Bar Options





Gas Engine, Ambulance Prep pkg.

$129,308.85

$129,569.17

$130,940.47

Diesel Engine, Kelderman air ride system, Ambulance Prep pkg.

$166,903.44

$170,147.42

$167,091.87

$170,334.95

$167,936.64

$171,180.62

$168,124.17

$171,368.15

Gas Engine, XL Trim level, #47A Ambulance Prep pkg.

$127,087.06

$131,722.89

$134,944.60

Ford F-series

$160,822.46

$165,519.05

Type III2017 E-350 4x2 138" Wheelbase, 80" CA, 96"x146" modular ambulance

body, 11,500# G.V.W.

Type IIIL2017 G4500 GAS 4x2 159.5" Wheelbase, 100"CA, 96" x 166" modular

ambulance body, 14,200# G.V.W.

Dodge Ram 4500 & 5500

Type I2017 RAM 4500 4x2 168.5" Wheelbase, 84" CA, 96" x 146" modular



ambulance body, 16,500# G.V.W

2017 G3500 GAS 4x2 139" Wheelbase, 80" CA, 96" x 146" modular


Type IIIL2017 G3500 GAS 4x2 159.5" Wheelbase, 100"CA, 96" x 166" modular


Type I2017 RAM 5500 4x4 192.5" Wheelbase, 107.9" CA, 96" x 172" modular


State of Ohio STS - Ambulance Pricing

Golden Eagle Base Model Ambulance Pricing

Diesel Engine, XLT Trim level, #47A Ambulance Prep pkg. Includes cloth bucket seats in cab.

Type I2017 F-350 4x2 169" Wheelbase, 84"CA, 96" x 146" modular ambulance

body, 14,000# G.V.W.

Type I2017 F-350 4x4 169" Wheelbase, 84"CA, 96" x 146" modular ambulance

body, 14,000# G.V.W

2017 RAM 5500 4x4 168.5" Wheelbase, 84" CA, 96" x 146" modular






Type I

Type IIIL2017 E-450 4x2 158" Wheelbase, 100" CA, 96" x 166" modular ambulance

body, 14,500# G.V.W

Type IIIXL2017 E-450 4x2 176" Wheelbase, 118" CA, 96" x 180" modular ambulance

body, 14,500# G.V.W

Chevrolet G-series

2017 RAM 4500 4x4 192.5" Wheelbase, 107.9" CA, 96" x 172" modular




Type I

Ford E-series

Type III





$167,048.80

$169,895.77

$169,210.44

$172,052.16

$171,258.99

$174,106.11

Diesel Engine, OEM air ride system, Ambulance/Emergency classification

$183,042.64

$187,689.15

DISCOUNT FOR MULTIPLE UNITS

Discount: $400 for 2 units; $500 for 3 units; $600 for 4 units; $700 for 5 units; etc. (Max discount = $2,000)

NOTE: This discount applies only to identical units built at the same time. It applies to each

unit BUT the entire discount is forfeited if the total number of units change after order is approved by Excellance.

CHASSIS: STANDARD SPECIFICATIONS

The cab for the chassis will be ordered "standard OEM white" from the chassis manufacturer.

Important: The Customer is responsible for all costs associated with (a) modifying,

repairing and replacing damaged and missing parts delivered with their chassis; (b) warranty

repairs; (c) correcting any feature not ordered correctly; and (d) transportation to and from the dealership.

Note: There is an upcharge to modify the modular body length or width shown above.

CHASSIS: SPECIAL OPTIONS Price Each

The vehicle will be ready for delivery w/ electrical diagrams, cleaned, inspected, fuel tanks full,

vehicle serviced, certified weight ticket, and copies of all warranties and owners manuals.

Air tanks installed by Excellance will have manual moisture relief valves.

* International Chassis service manual: Click "Publications" on the left menu

evalue.internationaldelivers.com/service/bodybuilder/general/

* Freightliner Chassis service manual: accessfreightliner.com

Under TOOLS & SERVICES click on "Freightliner Body Builder".

* Chevrolet/GMC Chassis service manuals: gmupfitter.com

* Ford Chassis service manuals: fleet.ford.com/truckbbas

* Dodge Chassis service manuals: rambodybuilder.com

17.3 139 * Additional Excellance owner/operator manual (price per additional manual) 222.81

Type

EHD I

2018 International 4300 169" Wheelbase, 101.9" CA, 96" x 166" modular


Type

EHD I

2018 Freightliner M2 170" Wheelbase, 104" CA, 96" x 166" modular


Type IL2017 F-450 4x4 193" Wheelbase, 108" CA, 96" x 172" modular ambulance

body, 16,500# G.V.W

Type I2017 F-450 4x2 169" Wheelbase, 84" CA, 96" x 146" modular ambulance

body, 16,500# G.V.W.

Type I2017 F-450 4x4 169" Wheelbase, 84" CA, 96" x 146" modular ambulance

body, 16,500# G.V.W


body, 16,500# G.V.W

Extra Heavy Duty chassis


body, 19,500# G.V.W


body, 19,500# G.V.W

If the chassis will be supplied by the Customer or Dealer there is a charge of $400.00 per chassis. This charge is for handling

the following items: unloading and storing the chassis, test driving and checking the chassis against the specifications

supplied by the customer, inventory and store loose parts delivered with the chassis, electrical tests on all chassis power

circuits, tire alignment, washing, detailing & polishing, fueling, checking gauges, brakes, all fluid levels and air in the tires prior

to final delivery.





17.3 140 * Additional set of customized Excellance electrical diagrams (price per set) 209.51

17.3 142 * Running Boards, Diamond Plate with grating and Excellance logo welded

17.3 143 into step area for Type III

17.3 144 * DELETE Diamond Plate running boards on Type III unit (379.12)

17.3 145 * Running Boards, solid Diamond Plate for Type I unit 656.81

17.3 146 * Running Boards, Diamond Plate with grating and Excellance logo welded 710.01

17.3 147 into step area for Type I

17.3 149 * Engine Block Heater (for Chevrolet gas engine) 364.14

17.3 161 CHASSIS: AIR RIDE & SUSPENSION OPTIONS

17.3 163 * Interface for Air Ride from module to a dealer or customer supplied chassis. 264.39

17.3 164 * This includes a dump circuit with override switch at the rear module door and

17.3 165 a dump circuit in the cab of the chassis.

17.3 167 Note: Ping Tanks are NOT included with Air Ride Systems unless noted.

17.3 169 * Rear Air Ride Suspension for F-series Kelderman ** (includes compressor) 9,133.32

17.3 170 * Rear Air Ride Suspension for Chevy Kelderman ** (includes compressor) 8,657.81

17.3 171 * Rear Air Ride Suspension for Dodge Kelderman ** (includes compressor) 9,075.71

17.3 172 * Rear Liquid Spring Suspension for E-series ** (see NOTE below) 9,541.56

17.3 173 * Rear Liquid Spring Suspension for F350/F450 ** (see NOTE below) 10,595.62

17.3 174 * Rear LiquidSpring Suspension for F-650 ** (see NOTE below) 10,861.62

17.3 175 * Rear LiquidSpring Suspension for G-series ** (see NOTE below) 9,787.68

17.3 176 * Rear LiquidSpring Suspension for Dodge ** (see NOTE below) 10,964.80

17.3 177 * Rear LiquidSpring Suspension for TerraStar ** (see NOTE below) 11,230.80

17.3 178 * Rear LiquidSpring Suspension for DuraStar ** (see NOTE below) 11,230.80

17.3 179 * Rear LiquidSpring Suspension for FL M-2 ** (see NOTE below) 11,353.86

17.3 180 * Rear Air Ride Suspension for E-350 Granning ** (includes compressor) 6,105.12

17.3 181 * Rear Air Ride Suspension for E-450 Granning ** (includes compressor) 7,622.53

17.3 182 * Rear Air Ride Suspension for F-350 Granning ** (includes compressor) 7,493.43

17.3 183 * Rear Air Ride Suspension for F-450 Granning ** (includes compressor) 9,222.43

17.3 184 * Rear Air Ride Suspension for G-series Granning ** (includes compressor) 7,722.75

17.3 185 * Rear Air Ride Suspension for C-series Granning ** (includes compressor) 7,968.87

17.3 186 * Dual Leveling Valve option for medium duty chassis 637.57

17.3 187 * Ping Tank Kit for Air Ride Suspension (one kit needed per air ride) 601.93

17.3 188 ** WEIGHT ADVISORY: This item will affect GVW and payload availability.

17.3 189

17.3 190 * The compressor for Air Ride shall be located:

17.3 191 * Lower aft of L3/2 compartment with vented cover

17.3 192 * Forward of L1 compartment with vented cover

17.3 193 * Lower aft of R1 compartment with vented cover

17.3 194

17.3 195 * If this unit has an Air Ride feature, choose on of the following:

17.3 196 * Activate Air Ride "dump" feature automatically when left rear door is open

17.3 197 Override switch at rear of module on curbside door.

17.3 198 Override switch at rear of module on curbside wall.

17.3 199 * Activate Air Ride "dump" feature manually. Install dump switch(es) at:

17.3 200 * streetside at rear entry door

17.3 201 * curbside at rear entry door

17.3 202 * in cab on cab console

17.3 203 * specify location for override switch:

17.3 204 * Air Ride installation include "down" indicator light on front console.

17.3 205

17.3 206 * Air Ride "down" buzzer installed on front console & activated when in gear. 97.44

17.3 207 * OEM air dump switch on dash to remain enabled unless otherwise specified in Customer Notes.

17.3 208 Note: EHD chassis has OEM switch in cab console as part of an OEM air ride package.

17.3 209

17.3 210 NOTE: Order OEM snow chains installed on chassis whenever possible.

17.3 211 * "On-Spot" snow chain system with chain tray (without compressor) 2,420.74

17.3 212 * "On-Spot" snow chain system with chain tray (with compressor) 3,142.30





17.3 213 NOTE 1: CONSULT FACTORY BEFORE SPECIFYING SNOW CHAINS WITH AN AIR RIDE SYSTEM !

17.3 214 NOTE 2: SPECIFY LOCATION FOR COMPRESSOR:

17.3 215 * Vented cover for air compressor for snow chain system 152.15

17.3 219

17.3 221 * Note: Brake Retarder requires an external battery compartment on a Type I unit.

17.3 222 * For battery compartment and third battery see line # 842

17.3 223 ** WEIGHT ADVISORY: This item will affect GVW and payload availability.

17.3 224 WARNING : Installation of Brake Retarders on a light-duty cutaway chassis can exceed the load rating

17.3 225 for the front axle -- violating FMVSS and QVM specifications which will void the chassis warranties !

17.3 226 * Brake Retarder control box to be located under body of module.

17.3 227 * Brake Retarder control box located in forward section of L3/2 compartment. 228.48

17.3 228

17.3 239 CHASSIS: TIRE / WHEEL OPTIONS Price Each

17.3 240

17.3 241 OEM Steel-belted All-Weather Radial tires per chassis specifications

17.3 242

17.3 246 Select one of the following options if there is a spare tire:

17.3 247 * Spare tire shall be "shipped loose" No charge

17.3 248 * Spare tire shall be installed in L3/2 No charge

17.3 249 * Spare tire to be installed in Short L1 $312.62 charge recorded at line # 878

17.3 250 * Spare tire to be installed in Short R1 $299.32 charge recorded at line # 985

17.3 251

17.3 252 * Wheel Inserts for E-series "Phoenix" stainless steel w/ rear air valve extension 340.83

17.3 253 * Wheel Inserts for F-350, "Phoenix" stainless steel with rear air valve extension 347.48

17.3 254 * Wheel Inserts for F-450, "Phoenix" stainless steel with rear air valve extension 364.77

17.3 255 * Wheel Inserts for Dodge 4500, "Phoenix" stainless steel w/ rear valve extension 409.99

17.3 256 * Wheel Inserts for C3500, "Phoenix" stainless steel w/ rear air valve extension 347.48

17.3 257 * Wheel Inserts for G-series, "Phoenix" stainless steel w/ rear air valve extension 347.48

17.3 258 * Wheel Inserts for FL M-2 w/19.5" wheels, "Phoenix" s.s. w/ rear air valve ext. 380.73

17.3 259 * Wheel Inserts for International w/19.5" wheels, "Phoenix" s.s. w/ rear valve ext. 409.99

17.3 260

17.3 261 * Hub and Lug Nut Covers: Chrome baby moon hub covers for front wheels and 370.27

17.3 262 chrome high hat hub covers for rear wheels with chrome covers for all lug nuts.

17.3 263

17.3 264 * Install customer / dealer provided wheel covers: Customer supplied part: 250.00

17.3 265 Installation charge for above customer supplied part: 61.53

17.3 276

17.3 277 CHASSIS: AIR HORN OPTIONS 0 0 Price Each

17.3 280

17.3 281 * Buell air horns w / compressor (Compressor w/ vented cover in compartment, 1,419.60

17.3 282 tank located under module, and control switch to activate air horn).

17.3 283 Compressor to be installed in: L3/2 compartment 153.83

17.3 284 Specify compartment other than L3/2 for compressor: 153.83

17.3 286 * Buell air horns w / Valve and Tank to be used with EHD chassis air 840.98

17.3 287 system via brake protection valve.

17.3 288 * Dual underbody air storage tanks with manual moisture drains with remote 989.20

17.3 289 * control cable installed at rear of module

17.3 290

17.3 291 trumpet on curbside: trumpet on streetside: 0

17.3 292 Specify length of trumpets for horns: 0.00

17.3 293 (Options: 10", 12", 15", 18", 24") NOTE: 12", 15", 18" or 24" air horns mounted

17.3 294 in bumper require an extended bumper. See line # 357

17.3 295

17.3 296 * Grover #1510 (24") air horn system for chassis WITH existing air supply. 864.57

17.3 297 * Grover #1510 (24") air horn system for chassis WITHOUT existing air supply. 1,330.77

17.3 298 * Aluminum pedestal mount for air horns on front of module (price each) 269.71

17.3 299

17.3 300 Select one of the following mounting locations for air horns:





17.3 301 * Mount air horns on existing bracket for front light bar 261.08

17.3 302 * Mount air horns on front of module (includes one aluminum pedestal mount) 269.71

17.3 303 * Mount air horns on streetside of the hood for EHD cab. 184.59

17.3 304 * Mount air horns on the curbside of the hood for EHD cab. 184.59

17.3 305 * Mount air horns on roof of cab. (Beware of noise level ). 246.12

17.3 306 * Mount 10" Buell air horns in Chevy or GMC G-series OEM bumper. 430.71

17.3 307 * Mount 10" Buell air horns in Ford E-series OEM bumper. 430.71

17.3 308 * Mount 10" Buell air horns in Ford F-series OEM bumper. 1,273.46

17.3 309 * Mount Buell air horns in extended bumper on EHD chassis. 430.71

17.3 310 * Mount Buell air horns in extended bumper on Chevy chassis. 430.71

17.3 311

17.3 312 Control switch to activate air horn to be located at:

17.3 313 Driver's left foot control (STANDARD)

17.3 314 * Passenger's right foot control (in lieu of driver's left foot control) 39.70

17.3 315 * Chassis horn ring on steering wheel (in lieu of driver's left foot control) 62.48

17.3 316 Note: The above option will not allow the operation of the siren horn.

17.3 317 * Passenger's right foot control (in addition to driver's left foot control) 120.23

17.3 318 * Chassis horn ring on steering wheel (in addition to driver's left foot control) 143.01

17.3 319 * Momentary switch on console in cab (in addition to driver's left foot control) 147.00

17.3 320 * Momentary switch on console in cab (in lieu of driver's left foot control) 35.71

17.3 321 * Operate air horns on an EHD unit via Lanyard valve located :

17.3 322 * in ceiling on driver's side 189.56

17.3 323 * in ceiling on passenger's side 189.56

17.3 324 * in ceiling in center of cab headliner 189.56

17.3 334

17.3 335 CHASSIS: EXTERIOR OPTIONS Price Each

17.3 336

17.3 337 * Pre-wire front end for future installation of fog lights with switch on console 162.96

17.3 338

17.3 339 * Perlux-brand Driving Lights: Clear (price is for a pair of lights) 391.72

17.3 340 * Perlux-brand Driving Lights: Amber (price is for a pair of lights) 391.72

17.3 341

17.3 342 * Peterson-brand Halogen Fog Lights: Amber (price is for a pair of lights) 210.84

17.3 343 * Hella-brand #550 Jumbo Fog Lights: Amber (price is for a pair of lights) 269.36

17.3 344 * Hella-brand #550 Jumbo Fog Lights: Clear (price is for a pair of lights) 269.36

17.3 345

17.3 346 * Tow Hooks, chrome, front (2), recessed without door (EHD only) 422.38

17.3 347 * Tow Hooks, chrome, rear (2), recessed with door (any chassis) 448.98

17.3 348 * Tow Eyes, black, rear (2), w/ 8" round hole for open access (any chassis) 488.88

17.3 349 * Tow Eyes, chrome, rear (2), recessed with door (any chassis) 523.46

17.3 350 * Tow Eyes, chrome, rear (2) in recessed polished housings (without door) 555.38

17.3 351

17.3 352 * Grill Guard, Chrome, for F-series chassis 987.56

17.3 353 * Grill Guard, Chrome, for C3500 chassis 987.56

17.3 354 * Grill Guard, Chrome, for F-series chassis with Brush Guards 1,310.12

17.3 355 * Grill Guard, Chrome, for C3500 chassis with Brush Guards 1,310.12

17.3 356

17.3 357 DO AIR HORNS SELECTED ABOVE REQUIRE THE FOLLOWING OPTION? NO

17.3 358 * 10" diamond plate bumper extension (price is for bumper extension only) 1,496.60

17.3 359 * Add one chain (storage) box w/ lid to bumper extension 611.94

17.3 360 * Add two chain (storage) boxes w/ lids to bumper extension 1,223.88

17.3 361

17.3 362 * Fuel Tank & Battery Box cover, Diamond Plate, for EHD chassis, custom made 1,935.50

17.3 363 by Excellance (price does not include slide-out tray for Battery Box)

17.3 364 * Fuel Tank & Battery Box cover, Diamond Plate, for EHD chassis, custom made 2,710.40

17.3 365 by Excellance (price does include slide-out tray for Battery Box)

17.3 366 * Extended Fuel Tank & Battery Box cover, Diamond Plate, for extended EHD 2,886.66

17.3 367 chassis, custom made by Excellance (price does not include slide-out tray for Battery Box)

17.3 368 * Extended Fuel Tank & Battery Box cover, Diamond Plate, for extended EHD 3,899.35

17.3 369 chassis, made by Excellance (price does include slide-out tray for Battery Box)





17.3 370

17.3 371 * Bug Shield, Clear 205.35

17.3 372 * Bug Shield, Smoke Tint 205.35

17.3 373

17.3 376 * Mirrors, VELVAC 715437 Deluxe (includes refinish of cab doors) 1,221.43

17.3 377 * Mirrors, VELVAC 715437 Deluxe (NO refinish of cab doors) 913.78





17.3 382 * Mirrors, VELVAC 715422 (heated / remote) (includes refinish of cab doors) 1,154.93

17.3 383 * Mirrors, VELVAC 715422 (heated / remote) (NO refinish of cab doors) 847.28





17.3 388

17.3 389 * Mud Flaps, 2 Front 132.20

17.3 390 * Mud Flaps, 2 Rear

17.3 391

17.3 392 * (2) Truck-Lite #40003 cab door-activated Running Board Courtesy lights 211.19

17.3 393 mounted on front of module (4" clear incandescent lights)

17.3 394 * (2) Truck-Lite #4060C 4" white L.E.D. cab door-activated Running Board 257.74

17.3 395 Courtesy lights mounted on front of module

17.3 406

17.3 407 CHASSIS: INTERIOR CAB OPTIONS Price Each

17.3 408

17.3 409 Select one of the following colors for the interior of the cab:

17.3 410 Note: "Gray" is the only "stock" kept in inventory by Excellance. All other colors are special order.

17.3 411 Ford E-series: medium gray interior cab color is the only choice available

17.3 412 Ford F-series: medium gray interior cab color

17.3 413 Ford F-series: tan interior cab color

17.3 414 GM light duty: gray interior cab color

17.3 415 GM light duty: blue interior cab color

17.3 416 GM light duty: charcoal interior cab color

17.3 417 GM light duty: beige interior cab color

17.3 418 Navistar: gray interior cab color

17.3 419 Navistar: beige interior cab color

17.3 420 Freightliner: gray interior cab color is the only choice available.

17.3 421

17.3 422 Cab floorboard to have rubber matting

17.3 423 * Carpet in lieu of rubber mats (interior of cab) N/C only on special order chassis

17.3 424

17.3 425 * Kickplate, Diamond Plate, bottom of cab doors 229.46

17.3 427 * Aircraft Dome Light (in ceiling of cab) in addition to standard dome light 213.68

17.3 428 * Red 4-1/2" dome light (in cab ceiling) w/ switch at console - added to std dome 279.02

17.3 439

17.3 440 CHASSIS ELECTRICAL SYSTEM: STANDARD SPECIFICATIONS

17.3 442 OEM auto-throttle, with on/off switch - EHD units only

17.3 443 Module disconnect power switch

17.3 444 This GM chassis will NOT have the automatic high-idle module in lieu of

17.3 445 the OEM manual activation.

17.3 446 * Install the automatic high-idle module in lieu of the OEM manual activation. 209.51

17.3 447 Type III light duty includes addition of exterior battery compartment in R4-2

17.3 448 OEM alternator(s) with internal regulator

17.3 449 A GM chassis with a gasoline powered chassis requires an additional or upgraded alternator!

17.3 450 The additional alternator was ordered with the chassis so the chassis has two OEM alternators OR

17.3 451 * Mounting kit with 145 amp alternator (in addition to OEM alternator) 1,458.17

17.3 452 * Mounting kit with 160 amp alternator (in addition to OEM alternator) 1,631.07

17.3 453 Back-up alarm, reverse activated





17.3 454 * Vented cover for external rectifier located in compartment L3/2. 237.79

17.3 455 Note 1: Order large capacity alternators with EHD chassis whenever possible!

17.3 456 Note 2: Changing any Ford OEM alternator violates QVM and voids Ford warranty.

17.3 467

17.3 468 CHASSIS ELECTRICAL SYSTEM: INTERIOR CAB OPTIONS Price Each

17.3 469

17.3 470 Engine cover mounted console with "quick release" feature on Type III units

17.3 471 Floor mounted console with "quick release" feature on Type I and EHD units

17.3 472 * Enter number of spare switches to be installed in front console for future items 16.79

17.3 473 * Enter number of spare switches to be installed in rear console for future items 16.79

17.3 474 * Enter number of holes to be cut in console for radio heads (price per hole) 61.53

17.3 475 Measurement each for radio head:

17.3 476 * Map / Binder case mounted on floor in cab 746.55

17.3 477 Specify number of sections for map / binder case here: 3

17.3 478 Specify width (in inches) between each partition here: 2

17.3 479 * Two cup holders in front console 60.03

17.3 480

17.3 481 Map Light, Flex-head Littlelite with red lens (12" shaft) located on front console

17.3 482 * DELETE "standard" Map Light on front console (79.98)

17.3 483 * Additional Map Light, Flex-head Littlelite with red lens, 6" shaft 110.74



17.3 486 * Specify location for additional light:

17.3 487 * Specify location for additional light:

17.3 488

17.3 489 Combination Volt / Amp / System Check digital meter with low voltage alarm

17.3 490 * Analog Voltmeter and Analog Ammeter in lieu of standard Combo digital meter

17.3 491

17.3 492 * Hour meter, Digital (TST brand) to be located in console 156.34

17.3 493 * Hour meter, Digital (TST brand) to be located in seat base (Type III units only) 156.34

17.3 494 * Hour meter, Analog (TST brand) to be located in console 180.81

17.3 495 * Hour meter, Analog (TST brand) to be located in seat base (Type III units only) 180.81

17.3 496 * Hour meter, Analog (Hobbs brand) to be located in console 181.58

17.3 497 * Hour meter, Analog (Hobbs brand) to be located in seat base (Type III units) 181.58

17.3 498 Note: Order OEM hour meter with chassis whenever possible.

17.3 499

17.3 500 * Ignition security system, anti-theft device, #ETISSO 240.10

17.3 501

17.3 502 * Safety Vision SV-CLCD-70B rear camera system with LCD flat screen 1,705.90

17.3 503 monitor on the cab console (includes 12 foot monitor cable)

17.3 504

17.3 505 * Pro-Vision TV-205 rear camera system with 5" LCD flat screen 1,375.15

17.3 506 monitor on the cab console.

17.3 507

17.3 508 * Pro-Vision TV-505 rear camera system with 7" LCD flat screen 1,435.00

17.3 509 monitor on the cab console.

17.3 510

17.3 511 * Add a second single Pro-Vision camera (#PC-1110 kit) in the interior of the 705.04

17.3 512 patient compartment to be viewed by the monitor specified above.

17.3 513

17.3 514 * Road Safety "SafeForce" Vehicle System w/ RF Communications and 9,064.16

17.3 515 Spotter Switch (includes On-Board Computer, Vehicle RF Data Transceiver, Accelerometer Module, etc.)

17.3 516

17.3 526 MODULAR BODY: STANDARD SPECIFICATIONS

17.3 528 All aluminum modular ambulance body with 1/4-inch thick aluminum corner extrusions

17.3 529 Module headroom shall be 69 inches for this non-EHD unit.

17.3 530 * Module headroom shall be 72 inches for this non-EHD unit. 1,426.67

17.3 531 Module headroom shall be 72 inches for EHD unit.

17.3 532 * Module headroom shall be 69 inches for this unit.





17.3 533 All aluminum framework with special anti-corrosion barrier applied to all fasteners, hinges, and components

17.3 534 Aluminum exterior skin shall be .125" thick, attached by continuous welds at all seams and corners

17.3 535 Aluminum exterior roof skin shall be .125" thick aluminum

17.3 536 * Tropical roof with .125" diamond-plate aluminum 1,905.54

17.3 537

17.3 538 3 module entry doors and all exterior compartment doors insulated with 2" Styrofoam planking

17.3 539 * Truck-Lite part # 30286R 2-inch diameter lights to be used as…

17.3 540 * Door-activated flashing red LED warning light on interior of side entry door 144.34

17.3 541 * Door-activated flashing red LED warning light on interior of each rear door 288.68

17.3 542 2 key locking module entry door handles all keyed alike

17.3 543 Left rear door shall close with an automatic "slam latch"

17.3 544 SUBSTITUTION: Left rear door will close w/ manual dowel rods ILO "slam latch" (824.74)

17.3 545

17.3 546 SUBSTITUTION: 3" Grabber on curbside entry door in lieu of spring door check 37.54

17.3 547 * Exterior vertical grab handle (w/ rubber insert) adjacent to side entry door 111.27

17.3 548 * Aluminum door-caddy storage cabinet in curbside entry door 863.03

17.3 549 Number of grabber / hold-open devices with gaskets: 2 on each rear entry door

17.3 550 Polished extruded aluminum drip rails over all module entry doors and exterior compartment doors

17.3 551 * Polished Aluminum Drip Rail around entire module roof perimeter 246.93

17.3 552 Fuel fill housing for chassis to be: recessed cast aluminum housing(s)

17.3 553 * Number of Fuel Fills with Hinged Door in lieu of standard fuel fill(s) 40.67

17.3 554 * Drip Guard under fuel fill to bottom edge of module (Diamond plate) 136.19

17.3 555 * Drip Guard under fuel fill to bottom edge of module (Stainless Steel) 150.82

17.3 556 1 set aluminum diamond plate stone guards for front of unit

17.3 557 * 1 set aluminum diamond plate stone guards for rear of unit 229.46

17.3 558 1 set diamond plate rub rails with aluminum tubular support & plastic spacers off body

17.3 559 2 aluminum wheel wells

17.3 560 1 set polished cast aluminum module fenderettes

17.3 561 * 1 set of rubber fenderettes (in lieu of aluminum fenderettes)

17.3 562 * Aluminum diamond plate overlay above rear wheel wells 681.73

17.3 563 1 diamond plate rear kick panel

17.3 564 8 body mounting 5/8" diameter Grade 8 bolts w/ heavy duty wear point spacers

17.3 565 10 body mounting 5/8" diameter Grade 8 bolts w/ heavy duty wear point spacers

17.3 566

17.3 567

17.3 568 1 custom-made aluminum diamond plate rear bumper with the following features:

17.3 569 angled rear corners

17.3 570 folding step built into bumper

17.3 571 1 dock bumper(s) each side of bumper

17.3 572 All windows installed in the patient compartment come with "privacy glass"

17.3 573 Fixed window for each rear entry door. Specify size: 12" x 36"

17.3 574 * Add 2nd window in each rear entry door. Specify size: call factory 402.36

17.3 575 Fixed curbside entry door window. Specify size: 18" x 24"

17.3 576 * Sliding curbside door window w/ screen. Size: 18" x 24" 119.12

17.3 577 * Add 2nd window in curbside entry door. Specify size: call factory 409.99

17.3 578

17.3 586 Price Each

17.3 587 MODULAR BODY: OPTIONS

17.3 589 * Modify modular body standard length by 6 inches or less 1,975.47

17.3 592 Type III: Walk-thru between cab and module with sliding lockable door

17.3 593 * Type III: "Open" Walk-thru between cab and module (without sliding door) (153.83)

3/4-inch thick composite floor with .063" aluminum subfloor insulated with Polystyrene foam

planking

Curbside entry door equipped with gas shock and nylon restraint strap to reduce opening

and closing force

10 body mounting 5/8" diameter Grade 8 bolts w/ heavy duty wear point spacers &

outrigger supports

8 body mounting 5/8" diameter Grade 8 bolts w/ heavy duty wear point spacers & outrigger

supports





17.3 594

17.3 595 * Type III: Replace walk-thru feature with pass-thru sliding window and 1,970.50

17.3 596 additional cabinetry

17.3 597 * Type I: Cabinet below pass-thru window to have dual hinged mica-faced doors

17.3 598 * Type I: Cabinet below pass-thru window to have dual sliding polycarbonate doors.

17.3 599 * Type I: Crawl-thru option with sliding door (no cap on roof) 1,681.19

17.3 600 * Type I: "Open" crawl-thru without sliding door (no cap on roof) 1,447.57

17.3 601 * EHD Type I: Walk-thru between cab and module with sliding lockable door

17.3 602 * EHD Type I: "Open" Walk-thru between cab and module (without sliding door) (320.08)

17.3 603 * EHD Type I: Replace walk-thru feature with pass-thru sliding window and

17.3 604 a cabinet with a hinged door below the pass-thru window

17.3 605

17.3 606 * Electric step (RV style) under curbside door to operate when door is 801.43

17.3 607 * opened (with override switch located inside of curbside door)

17.3 608

17.3 609 * Buzzer and light on front console to activate when electric step under curbside 138.85

17.3 610 * door is deployed and transmission is placed into gear

17.3 611

17.3 612 Door Sill protectors, Stainless Steel, to be installed as follows:

17.3 613 * Door Sill protector for side personnel door 79.40

17.3 614 * Door Sill protectors for ALL compartment doors 445.62

17.3 615 * Door Sill protector for only this compartment: 94.78

17.3 616

17.3 617 * Additional module window installed: curbside above squad bench

17.3 618 * Straight Fixed 18" X 36" 461.58

17.3 619 * Straight Sliding 18" X 36" 538.72

17.3 620

17.3 621 with pencil tray? fixed or two-piece sliding

17.3 622 * Dry-erase board over squad bench: no fixed 174.58

17.3 623 Overall size of board to be: 18 x 24 inches

17.3 624

17.3 625 * "Limo-style" glass. Location:

17.3 626 * Enter number of windows for "Limo-style" glass (price is per window) 46.73

17.3 627

17.3 628 * "Mirror-style" privacy glass. Location:

17.3 629 * Enter number of windows for "Mirror-style" privacy glass (price is per window) 77.49

17.3 630

17.3 631 * MacLift Hydraulic lift for Stryker on Type I w/ special rear bumper design. 12,429.55

17.3 632 * MacLift Hydraulic lift for Stryker on Type III w/ special rear bumper design. 12,429.55

17.3 633 * MacLift Hydraulic lift for Ferno on Type III w/ special rear bumper design. 12,429.55

17.3 634 * Bariatric lift, rear-mounted with special rear bumper design. 14,158.55

17.3 635

17.3 648 CAB / MODULE PAINT AND LETTERING: STANDARD SPECIFICATIONS

17.3 650 Outside of 4 outer wheels (w/o inserts) to be painted with Krylon spray paint to match module standard

17.3 651 * Outside of 4 outer wheels (w/o inserts) painted with paint used for module 525.49

17.3 652 * DELETION CREDIT: Do not paint the 4 outer wheels (74.83)

17.3 653 Include one touch up paint kit for each color used standard

17.3 654 Select one of the following three options:

17.3 655 Install Federal ambulance markings ("Star of Life" Kit) upon customer pick-up at factory

17.3 656 Install ambulance "Star of Life" at this location:

17.3 657 Ship loose Federal ambulance markings ("Star of Life" Kit)

17.3 658 * DELETION CREDIT: Delete Federal ambulance markings (312.00)

17.3 659

17.3 660 PAINT OPTIONS

17.3 662 The cab for the chassis will be ordered and painted standard OEM white.

17.3 663 The module shall be painted the same color to match the chassis.

17.3 664 Color & Paint Number:

17.3 665 * Paint entire module any color other than OEM white: 1,406.79

NOTE: Deleting the sliding door (resulting in an "open" walk-thru) does not comply with

"KKK" regulations.





17.3 666 * Paint module lower half a different color: 1,496.60

17.3 667

17.3 668 * Paint cab any color other than OEM white: 4,459.98

17.3 669 * Paint lower half of cab a different color: 3,096.38

17.3 670

17.3 671 * Paint roof of the module white (not visible from ground level) 1,004.36

17.3 672 * Paint roof of the module white (roll white roof paint over top edge of module sides) 1,127.42

17.3 673

17.3 674 * The paint finish will be hand glazed with a non-wax based product. standard

17.3 675

17.3 676 * Metallic paint will not be used anywhere on this unit.

17.3 677 * Metallic paint to be used to paint the lower half of body & cab 999.39

17.3 678

17.3 689 BELTLINE

17.3 690 Single 11-inch beltline reflective orange stripe on sides of module & cab standard

17.3 691 * DELETE standard 11" reflective beltline stripe (1,322.23)

17.3 692 * Painted Beltline Stripe (ILO reflective striping) (non-KKK compliant) 801.50

17.3 693 * Specify color & paint number here:

17.3 694 * Specify the width of single beltline here (in inches):

17.3 695

17.3 696 * Double Beltline Stripes (when both stripes are painted the same color) 678.44

17.3 697 * Double Beltline Stripes (when each stripe is painted a different color) 1,724.45

17.3 698 * Specify width of top beltline stripe here (in inches):

17.3 699 * Width of bottom beltline stripe here (in inches):

17.3 700 * Specify the color & paint # for top beltline stripe:

17.3 701 * Specify the color & paint # for bottom beltline stripe:

17.3 702

17.3 703 * Additional Beltline Stripes (when stripe is painted same color as an existing stripe) 678.44

17.3 704 * Additional Beltline Stripes (when each stripe is painted a different color) 801.50

17.3 705 * Specify width of additional beltline stripe (in inches):

17.3 706 * Specify color & paint # for additional beltline stripes:

17.3 707

17.3 708 SKIRTLINE & ROOFLINE

17.3 709 * Roofline Paint stripe 678.44

17.3 710 * Specify color and paint number here:

17.3 711 * Specify the width for above option here (in inches):

17.3 712 * Skirtline Paint stripe 801.50



17.3 715 * Double Skirtline 1,265.46

17.3 716 * Specify color and paint number for top skirtline here:

17.3 717 * Specify the width of top skirtline here (in inches):

17.3 718 * Specify color and paint number for 2nd skirtline:

17.3 719 * Specify width of 2nd (bottom) skirtline here (inches):

17.3 720

17.3 721 * QRS design in paint stripe (ATTACH DIAGRAM SHOWING BOTH THE 1,453.41

17.3 722 DESIGN AND LOCATION FOR QRS -- ALSO SPECIFY WIDTH OF DESIGN)

17.3 723

17.3 724 * Double "Z" Stripe 1,706.18



17.3 727 * Single "Z" Stripe 1,193.99



17.3 730 * Hockey Stick Stripe 1,193.99



17.3 733 * Flying "H" paint stripe 1,952.30







17.3 736

17.3 737 PINSTRIPE

17.3 738 Black reflective 1/4" pinstripe tape on top & bottom of Beltline standard

17.3 739 *Additional reflective tape pinstripes to be applied to additional beltlines 347.55

17.3 740 * DELETION: No pinstripe tape to be applied on top or bottom of painted beltline 267.75

17.3 741 * DELETION: No pinstripe tape AND no painted beltline to be applied by factory (286.02)

17.3 742 10.00

17.3 743

17.3 744 * Use 1/2" reflective pin striping in lieu of standard 1/4" reflective pin striping 66.50

17.3 745 * Painted pinstripe. Specify color and paint number: 781.55

17.3 746 * Specify the width of painted pinstripe (in inches):

17.3 747

17.3 748

17.3 749 REFLECTIVE "SCOTCHLITE" STRIPING

17.3 751 PRICING FOR WHITE REFLECTIVE STRIPING:

17.3 752 1 inch Reflective White Stripe 443.66






17.3 758 8 inch Reflective White Stripe 1,079.12



17.3 761

17.3 762 PRICING AND "CODES" FOR REFLECTIVE NON-CUSTOM COLOR STRIPE:

17.3 763 1 = 1 inch Reflective Color Stripe 448.98






17.3 769 8 = 8 inch Reflective Color Stripe 1,120.35



17.3 772

17.3 773 "CODES" FOR REFLECTIVE STRIPES:

17.3 774 20 = #680-14 Orange 26 = #680-77 Green

17.3 775 21 = #680-64 Gold 27 = #680-81 Lemon Yellow

17.3 776 22 = #680-71 Yellow 28 = #680-82 Ruby Red

17.3 777 23 = #680-72 Red 29 = #680-85 Black

17.3 778 24 = #680-75 Blue 30 = #680-10 White

17.3 779 25 = #680-76 Light Blue

17.3 788

17.3 789 * Install customer / dealer provided reflective striping: Customer supplied part: 250.00

17.3 790 Installation charge of above customer supplied part: 615.30

17.3 791

17.3 792 NOTE: ATTACH A DIAGRAM SHOWING THE "LAYOUT" OF THE BELTLINE

17.3 793 AND THE LOCATION ON THE MODULE FOR THE BELTLINE.

17.3 794

17.3 807 LETTERING OPTIONS

17.3 808

17.3 809 Excellance will not supply or install any lettering. standard

17.3 810

17.3 811 Lettering to be provided and installed by Excellance is specified on an

17.3 812 attachment to this document AND priced on the attachment.

17.3 813

17.3 814 * Install customer / dealer provided lettering: Customer supplied part: 250.00

17.3 815 Installation charge of above customer supplied part: 1,353.66

17.3 816

* SUBSTITUTION: different color of reflective pinstripe in lieu of black:





17.3 817 * Install customer provided decals on cab doors: Customer supplied part:

17.3 818 Installation charge of above customer supplied part: 123.06

17.3 827

17.3 828 EXTERIOR COMPARTMENTS: STANDARD SPECIFICATIONS

17.3 830 All exterior compartment doors insulated with 2" styrofoam standard

17.3 831 206 latch w/ key locking stainless steel 9000 series D-ring handles with gaskets (where possible) standard

17.3 832 * SUBSTITUTION: Install fixed L-handles in in lieu of folding door handles. 61.53

17.3 833 Doors equipped with gas shocks to reduce opening and closing force standard

17.3 834 * SUBSTITUTION: 3" Grabbers in lieu of spring door checks (price per grabber) 37.54

17.3 835 * Specify which compartments will have 3" Grabbers:

17.3 836 * SUBSTITUTION: 4" Grabbers in lieu of spring door checks (price per grabber) 38.07

17.3 837 * Specify which compartments will have 4" Grabbers:

17.3 838 * SUBSTITUTION: Grease fitting style in lieu of spring door checks (price each) 34.22

17.3 839 * Specify each compartment to have Grease fittings:

17.3 840 Machine louvered or plastic venting, as needed, in all exterior compartments

17.3 841 Battery storage compartment below R4, WITH sliding tray (standard only on Type III)

17.3 842 * Add an external battery storage compartment w/ sliding tray for Type I module 934.43

17.3 843 * Add second 750 CCA battery in battery storage compartment (2 batteries total). 247.73

17.3 844 * Add second 750 CCA battery in battery storage compartment (3 batteries total). 247.73

17.3 845 * Add 2nd & 3rd 750 CCA battery in battery storage compartment (for a total 673.40

17.3 846 of 4 batteries). Note: the depth of this compartment must be 23 inches.

17.3 847 * Batteries to be wired in two "banks" with switching indicator lights labeled 1,085.77

17.3 848 * as Battery #1 & Battery #2 on front console with battery isolator.

17.3 849 Note: Battery storage compartment R4-2 to have 52C door latch in lieu of 206 latch

17.3 850

17.3 862 EXTERIOR COMPARTMENTS: OPTIONS

17.3 863 All aluminum unistruts to be welded into exterior compartments (no screws or rivets)

17.3 864 #REF! Price Each

17.3 866 Compartment L1: (Streetside Rear)

17.3 867 Tall L1 version - standard for 146" & 166" modules

17.3 868 * Backboard storage in L1 will have 2 adjustable vertical dividers

17.3 869 * DELETE backboard storage from L1 compartment ( no vertical dividers in L1 ). (184.59)

17.3 870 Type of shelves in L1: Quantity Thickness of aluminum

17.3 871 Adjustable shelves with unistrut 3 0.125" standard

17.3 872 Fixed shelves 0 0.125" standard

17.3 873 Each additional shelf will cost $172.10

17.3 874 Inside / Outside access with interior cabinet door

17.3 875 * DELETE "inside" access for Tall L1 (184.59)

17.3 876 * Short L1 w/ additional interior cabinetry - optional for 146" & 166" modules 971.11

17.3 877 * Short L1 with NO interior cabinetry - optional for 146" & 166" modules

17.3 878 * 3/4 height L1 w/ interior-only cabinet above the L1 compartment 801.50

17.3 879 * Install spare tire in Short L1 - per selection at line # 248 312.62

17.3 880 One standard LED light in compartment - to be door activated standard

17.3 881 * Enter number of additional "standard" LED lights for this compartment 81.48

17.3 882 * Door-activated flashing red LED warning light on interior of door 159.64

17.3 883 * Interior door for L1 to be covered with Formica ILO polycarbonate 90.62

17.3 884 * Dual-doors (e.g., split doors) for interior access to L1 compartment 290.99

17.3 885 * Dual-doors (e.g., split doors) for L1 compartment exterior 848.05

17.3 886 * L1 exterior door to be louvered or vented (for generator storage) 492.24

17.3 887 * Turtle tile plastic matting for compartment floor 68.27

17.3 888 * Enter '1' here for Turtle tile on all 3 shelves of compartment 204.81

17.3 889 * Dri-Deck for compartment floor 64.28

17.3 890 * Enter '1' here for Dri-Deck on all 3 shelves of compartment 192.84

17.3 891 * Specify the color for the Turtle tile or Dri-Deck:

17.3 892 * Rubber mat for compartment floor 57.37

17.3 893 * Enter '1' for Rubber mats on all 3 shelves of compartment 172.10

17.3 901

17.3 902 Compartment L3/1: (Outside electrical compartment for power distribution panel)

17.3 903 * DELETE the L3/1 compartment and relocate the power distribution panel to 184.59





17.3 904 * inside the patient compartment in the front bulkhead cabinet behind the attendant seat.

17.3 905 * NOTE: Relocating the power distribution panel to the interior of the patient compartment

17.3 906 * may require using the cabinet above the walk-through OR the area below the pass-through

17.3 907 * on a Type I for the installation of optional electrical components.

17.3 908 * Electrical schematics to be installed in clear pouch on L3/1 compartment door 80.15


17.3 910 * Allow the light in the L3/1 compartment to operate via a switch mounted 166.95

17.3 911 * directly on the power distribution panel (to be battery powered) in lieu of

17.3 912 * operating from the magnetically controlled door switch.

17.3 913 * Key the exterior door latch for the L3/1 compartment differently from all other 30.77

17.3 914 * exterior compartment doors using a #545 lock and key (in lieu of the #1250 key).

17.3 918

17.3 919 Compartment L3/2: (Streetside Intermediate)

17.3 920 * Install spare tire in L3/2 - per selection made at line 246

17.3 921 Type of shelves in L3/2: Quantity Thickness of aluminum



17.3 924 Each shelf in this compartment costs $172.10

17.3 925 * Fixed vertical divider in L3/2. # of adjustable dividers: 2 419.02

17.3 926 * DELETE fixed vertical divider. Install adjustable dividers only. (161.28)

17.3 927 * Provide inside access to L3/2 with sliding polycarbonate doors 558.74

17.3 928 * Perforated aluminum metal cover for component installed in compartment 158.80

17.3 929 * Diamond plate cover for component installed in compartment 138.85




17.3 933 * Dual-doors (e.g., split doors) for L3/2 exterior - standard @ N/C on 166" boxes 848.05

17.3 934 * L3/2 exterior compartment door to be louvered or vented (for generator storage) 492.24

17.3 935 * Sliding tray (24" - 48" wide) manufactured by Excellance (rated for 150#) 788.20

17.3 936 * Sliding tray (24" - 48" wide) from "Slide Master" #SM2-LP (rated for 300#) 871.29





17.3 951

17.3 952 Compartment L4: (Streetside Forward)

17.3 953 * Fixed vertical divider in L4. # of adjustable dividers: 2 419.02

17.3 954 * DELETE fixed vertical divider. Install adjustable dividers only. -161.28

17.3 955 Type of shelves in L4: Quantity Thickness of aluminum







17.3 962 * Install switch in action area to activate light in L4 compartment for O2 gauge. 128.03

17.3 963 * Dual-doors (e.g., split doors) for L4 exterior (Consult Factory first) 848.05





17.3 978

17.3 979 Compartment R1: (Curbside Rear)

17.3 980 Short R1 - standard for 146" module

17.3 981 Short R1 - optional @ N/C for 166" module

17.3 982 Inside / Outside access for Short R1

17.3 983 * DELETE inside access in Short R1 (making a fixed lid on squad bench) resulting in:

17.3 984 * all exterior storage with outside access only to Short R1 (98.77)

17.3 985 * exterior storage w/ outside access & interior storage under squad bench lid 93.80





17.3 986 * dropwell in Short R1 for spare tire - per line # 249 299.32

17.3 987 * Dual-doors (split doors) for Short R1 compartment exterior 848.05

17.3 988 * Short R1 exterior door to be louvered or vented (for generator storage) 492.24



17.3 991 Type of shelves in Short R1: Quantity Thickness of aluminum




17.3 995

17.3 996 Tall R1 - standard on 166" & over boxes - includes short R2 unless deleted at 1027

17.3 997 Tall R1 - optional on 146" boxes 744.00

17.3 998 Note: a Tall R1 on a 146" box includes a short R2 unless it is deleted at line # 1027

17.3 999 * Backboard storage in Tall R1. # of adjust. dividers: 2 0.00

17.3 1000 * DELETE backboard storage from Tall R1 compartment. (123.06)

17.3 1001 Type of shelves in Tall R1: Quantity Thickness of aluminum




17.3 1005 * Fixed vertical divider in R1. # of adjustable dividers: 2 388.26

17.3 1006 Outside access for Tall R1

17.3 1007 * Provide inside access to Tall R1 w/ one hinged 623.56

17.3 1008 door(s) which will be made of polycarbonate

17.3 1009 One standard LED light in R1 compartment - to be door activated standard

17.3 1010 * Enter number of additional "standard" LED lights for R1 compartment 81.48






17.3 1026

17.3 1027 Compartment Short R2: (Curbside Rear) Only available if Tall R1 is selected.

17.3 1028 * DELETE Short R2 compartment (369.18)

17.3 1029 Inside / Outside access for Short R2

17.3 1030 * DELETE inside access in Short R2 resulting in:

17.3 1031 * all exterior storage with outside access only to Short R2 (128.21)

17.3 1032 * exterior storage w/ outside access & interior storage under squad bench lid 93.80

17.3 1033 Type of shelves in R2: Quantity Thickness of aluminum













17.3 1053

17.3 1054 Compartment R4: (Curbside Forward)

17.3 1055 Inside / Outside access for full height of R4 compartment

17.3 1056 * Inside access only for full height of R4 -- delete all outside access (352.52)

17.3 1057 * Outside access only for full height of R4 -- delete all inside access (352.52)

17.3 1058 * Inside / Outside access for only bottom portion of R4 -- with inside access only for top portion

17.3 1059 * Exterior door for R4 compartment to be "3/4 height" that stops at the top of outside access

17.3 1060 * Inside / Outside access for only top portion of R4 -- with inside access only for bottom portion

17.3 1061 * Exterior door for R4 compartment shall only be for that area with outside access





17.3 1062 * SUBSTITUTE: Two full height polycarbonate non-locking doors inside R4 (243.11)

17.3 1063 * SUBSTITUTE: 2 lower doors on inside of R4 shall be made with formica 154.63

17.3 1064 * DELETE the 2 lower doors on inside of R4 (for open access inside) (189.56)

17.3 1065 * DELETE the 2 upper doors on inside of R4 (for open access inside) (189.56)


17.3 1067 * DELETE standard cabinet beside drug box in R4 and expand drug box 101.43

17.3 1068 storage to include the area for this standard cabinet.

17.3 1069 Drug box storage in R4 shall have a locking formica door.

17.3 1070 Cabinet beside the drug box storage in R4 will have inside / outside

17.3 1071 access with a non-locking formica interior door.

17.3 1072 The vertically-hinged doors will be individually latching doors

17.3 1073

17.3 1074 * Eliminate both the drug box and the cabinet next to it, making R4 one single (173.60)

17.3 1075 large compartment.

17.3 1076

17.3 1077 * Relocate the HVAC system from over the R4 to the center of the 345.87

17.3 1078 bulkhead and install a cabinet in the top of the R4 with…

17.3 1079 dual sliding doors that are made of polycarbonate ("standard" with the above option)

17.3 1080 two horizontally-hinged cabinet doors of polycarbonate w/ gas shock hold-opens 216.16

17.3 1081 one horizontally-hinged cabinet door of polycarbonate w/ gas shock hold-opens 249.41

17.3 1082





17.3 1087

17.3 1088 * Roll up door for access to the lower half of interior R4 1,029.21

17.3 1089 * Drawers to be installed in R4. Location: 891.31

17.3 1090 * Nylon net w/ quick release buckles. Location: 254.60

17.3 1091



17.3 1094








17.3 1109

17.3 1110 Compartment R5 (Curbside Forward)

17.3 1111 * Compartment R5 -- WITHOUT interior cabinet 922.95





17.3 1116

17.3 1117 * Compartment R5 -- WITH interior cabinet with vented formica door 1,757.70

17.3 1118 Shelves in exterior R5 compartment: Quantity Thickness of aluminum




17.3 1122

17.3 1123 Shelves for interior R5 cabinet: Quantity Thickness of aluminum








17.3 1127 * Fixed vertical divider in R5. # of adjustable dividers: 2 449.79

17.3 1128 * DELETE fixed vertical divider. Install adjustable dividers only. -161.28



17.3 1131





17.3 1139

17.3 1140 * Sliding tray manufactured by Excellance (rated for 150#) 788.20

17.3 1141 * Sliding tray from "Slide Master" #SM2-LP (rated for 300#) 871.29

17.3 1148

17.3 1149 * A curbside wheel well compartment with 52C latch and 1,109.15

17.3 1150 * top-hinged door with gas-shock hold-open.

17.3 1151 Notice: Wheel well compartment is not recommended for Type I Ford chassis.

17.3 1152 * Inside / Outside access 202.86




17.3 1156 * Enter '1' here for Turtle tile for sliding tray 87.86


17.3 1158 * Enter '1' here for Dri-Deck for sliding tray 81.32



17.3 1161 * Enter '1' here for a Rubber mat for sliding tray 50.72

17.3 1168

17.3 1169 * A streetside wheel well compartment: 1,109.15




17.3 1173 * Enter '1' here for Turtle tile for sliding tray 87.86


17.3 1175 * Enter '1' here for Dri-Deck for sliding tray 81.32



17.3 1178 * Enter '1' here for a Rubber mat for sliding tray 50.72

17.3 1183

17.3 1184 * Additional locking drug box in existing cabinetry: 400.75

17.3 1185

17.3 1186 * Install Turtle Tile "Edging" in all 5 compartment floors 142.75

17.3 1187 * Install Dri-Deck "Edging" in all 5 compartment floors 126.39

17.3 1188 * Install Turtle Title "Edging" on all 6 compartment shelves 171.30

17.3 1189 * Install Dri-Deck "Edging" on all 6 compartment shelves 151.67

17.3 1190

17.3 1191 Five exterior compartment(s) to be finished in Excellance texturized paint. standard

17.3 1192 Specify each compartment here: ALL - EXCEPT R4 which is to be finished white

17.3 1193 Number of exterior compartment(s) to remain in raw aluminum with no special treatment.

17.3 1194 Specify each compartment here:

17.3 1195 * Number of exterior compartment(s) to be DA sanded / with Clearcoat 136.19

17.3 1196 * Specify each compartment here:

17.3 1197 * Number of exterior compartment(s) to be DA sanded / without Clearcoat 81.48


17.3 1199 * Number of exterior compartment(s) to have DA swirl pattern / with Clearcoat 166.95


17.3 1201 * Number of exterior compartment(s) to have DA swirl pattern / without Clearcoat 112.25


17.3 1203 * Number of compartment(s) to be .125" diamond plate (in lieu of .125" alum.) 229.46


17.3 1205 * Number of compartment(s) w/ diamond plate floor only, .125" thick 129.54






17.3 1207 Bio-Shield polyurethane spray-on coating for exterior compartments:

17.3 1208 * Enter '1' for Bio-Shield coating for up to 6 exterior compartments and 6 shelves 1,336.93

17.3 1209 * Enter number of exterior compartments over " 6 " for Bio-Shield coating 150.82

17.3 1210 * Enter number of individual compartments (in lieu of all compartments) 181.58

17.3 1211 * Specify compartments for coating:

17.3 1212 * Enter number of exterior shelves over " 6 " for for Bio-Shield coating 66.68

17.3 1213 * Enter number of individual shelves for coating (in lieu of all shelves) 88.13

17.3 1214 * Specify compartments for coating:

17.3 1215 * Specify color other than gray for spray-on coating: 90.79

17.3 1216

17.3 1217 * Number of compartment(s) with unistrut mounted horizontally on back wall 150.82


17.3 1219

17.3 1220 * Zico brand SCBA bracket with safety strap. Location: 169.26

17.3 1221 Specify the bottle style / size for safety strap:

17.3 1222

17.3 1223 * Enter number of restraint strap sets with quick-release buckle 44.07


17.3 1225

17.3 1226 * Compartment(s) to have 52C door latches (in lieu of 206 latches)

17.3 1227 Specify compartments for the above:

17.3 1228

17.3 1229

17.3 1230 Electric door lock options:

17.3 1231 * Electric door locks for module personnel doors only 1,044.65

17.3 1232 * Electric door locks for module personnel & R4 doors 1,167.38

17.3 1234 Note: If no module door has electric locks, then the first exterior compartment is $734.34

17.3 1235 and each additional compartment thereafter will cost $134.43

17.3 1236 If any module door has electric locks, $134.43 is the cost for each exterior compartment.

17.3 1237

17.3 1242Note: The additional charge for each

separate door lock switch: $92.12 0.00

17.3 1243

17.3 1244 * Electric door locks to have remote control activation 232.47

17.3 1245 * Concealed weatherproof override switch for electric door locks 162.96

17.3 1246 * Concealed override switch location: behind the front grill on the chassis

17.3 1247

17.3 1262 PATIENT COMPARTMENT: STANDARD SPECIFICATIONS

17.3 1264 Install clear polycarbonate throughout the unit.

17.3 1265 * Install smoke polycarbonate throughout the unit. 297.45

17.3 1266 * Install red polycarbonate throughout the unit. 149.82

17.3 1267 * Install this color of polycarbonate: throughout the unit. 302.77

17.3 1268Standard

17.3 1269 Door-activated flush-mounted stepwell light, LED Standard

17.3 1270 3 interior entry door panels, aluminum laminated with formica Standard

17.3 1271 Alternating red/white 10" reflective diagonal stripes on each Personnel Door Standard

17.3 1272 *DELETION CREDIT: No reflective diagonal stripes on Personnel Doors (263.94)

17.3 1273 * Brushed stainless steel kick panels, 9" high at bottom of each Personnel 317.59

17.3 1274 Door with 3-inch reflective red & white safety stripe on the interior face of door

17.3 1275 * Diamond plate kick panels, 9" high at bottom of each Personnel Door 264.39

17.3 1276 Grab handles for module doors to be: 1.25" diameter seamless stainless steel

17.3 1277 Grab handle(s) for the inside of the side entry door: 18" long Pricing:

17.3 1278 * SUBSTITUTION: "L" Handle Bar (in lieu of standard straight bar) 83.70

17.3 1279 Grab handle(s) on each rear door inside the module: "L" shape 33" x 17.5" Pricing:

17.3 1280 Aluminum walls laminated with formica Standard

17.3 1281 Aluminum ceiling finish painted white Standard

17.3 1282 Insulation in the module walls and ceiling Standard

Full seam-welded NFPA-compliant anti-skid aluminum diamond plate stepwell with flush

sweep-out design





17.3 1283 * Styrofoam planking (in lieu of standard insulation) to insulate walls and ceiling 369.18

17.3 1284 Welded tubular aluminum cabinet framework with cabinet tubular faces painted white Standard

17.3 1285 Sliding medical cabinet doors of 1/4" polycarbonate with full height extruded aluminum handles Standard

17.3 1286 All cabinet interiors are to be painted white Standard

17.3 1287 Streetside action area with solid surface counter top Pricing:

17.3 1288 The color for all counter tops will be: light gray w/ white & charcoal speckles 94.78

17.3 1290 Interior cabinet to have restocking feature (price each) 232.47

17.3 1296 Action area shelf to have lip Standard

17.3 1297Standard

17.3 1298 1 set EMT seat with belts and retractors Standard

17.3 1299 Squad bench w/vinyl covered padded split seat cushion and with a hinged

17.3 1300 sets of seatbelts and retractors: 3 red

17.3 1301 sets of patient restraint straps: 3 red

17.3 1302 Squad bench to have a solid vinyl covered padded back rest Standard

17.3 1303 * Squad bench to have a "split" back rest made of padded covered vinyl 166.95

17.3 1304 * OPTION: Streetside squad bench with storage under squad bench 1,202.25

17.3 1305 * OPTION: Streetside squad bench without storage under squad bench 814.80

17.3 1306 2 "No smoking oxygen equipped / Fasten your seatbelt" decals, one in cab and one in module Standard

17.3 1307Standard

17.3 1308 Two 72" x 1.25" diameter stainless steel overhead grab rails on 146" module: 2

17.3 1309 Two of 96" x 1.25" diameter stainless steel overhead grab rails on 166" module: 2

17.3 1310 * 96" x 1.25" diameter stainless steel grab rails in lieu of above standard 72" 91.19

17.3 1311 * 116" x 1.25" diameter stainless steel grab rails in lieu of above standard 96" 167.00

17.3 1312 1 CPR seat with vinyl covered padded seat and head protectors Standard

17.3 1313 CPR seat to have " fold down back rest " feature Standard

17.3 1314 * DELETE fold down feature on CPR seat back rest (resulting in stationary back) (61.53)

17.3 1315 * CPR seat to have "standard" across-the-lap seatbelt (which is not KKK compliant)

17.3 1316 * CPR seat to have 5-point harness system in addition to "standard" seatbelt 940.21

17.3 1317 * OPTION: Provide storage area under CPR seat 503.86

17.3 1318 * OPTION: Delete CPR seat. Extend action area with full-length countertop. Add one additional

17.3 1319 upper cabinet over action area & build full-height cabinet w/ vertical hinged door in aft action area w/ 3 shelves.

17.3 1320 * OPTION: Delete CPR seat. Extend action area with full-length countertop. Add 593.60

17.3 1321 one additional upper cabinet over action area and build two cabinets (w/ one shelf each) in aft action area.

17.3 1322 * OPTION: Eliminate countertop and cabinetry in aft action area. Widen CPR seat area to

17.3 1323 include dual seat belts.

17.3 1324

17.3 1335 PATIENT COMPARTMENT: OPTIONS Price Each

17.3 1337 Mica finish to be low gloss Standard

17.3 1338 * mica color to be light gray ( " studio gray " ) OR Standard

17.3 1339 * mica color to be tan ( " crème tranquility " )

17.3 1340 * Specify special mica color here: 50.00

17.3 1341

17.3 1342 * High back EMT Captains Chair (Bucket Seat) at Action Area w/ these features: Standard

17.3 1343 Built-in Child-Safety Seat? yes 199.50

17.3 1344 # of seat belt harness points: 4 179.55

17.3 1345 # of arm rests: 0 no arm rests 0.00

17.3 1346 * Swivel seat base (2-way swivel) Standard

17.3 1347 * Swivel seat base (8-way swivel) (not available with child seat) 13.30

17.3 1348 * Fixed seat base with locking storage underneath

17.3 1349 * Sewn upholstery Standard

17.3 1350 * Seamless upholstery 71.82

17.3 1351 * WISE brand Standard

17.3 1352 * EVS brand 460.53

17.3 1353

17.3 1354 Options: Surface mounted fold-down w/ velcro - Recessed - IV Hanger Hook (clip style)

17.3 1355 Type of IV holder Quantity Mounting location for IV holders:

17.3 1356 Rubber shaft fold-down w/ velcro 1 head of primary cot

oxygen compartment shall have one polycarbonate hinged access door for "M" & "H" size

cylinders

Removable wiring access panels, vinyl padded down the center of the ceiling w/ 1" x 2"

tubular supports





17.3 1357 Rubber shaft fold-down w/ velcro 1 head of squad bench

17.3 1364 Pricing: Up to 2 IV holders are at N/C; cost for each additional IV holder (over 4): $58.35

17.3 1365

17.3 1366 * Stainless steel Vertical Handrail / IV Pump mounting pole with stanchion 121.38

17.3 1367 Location: action area

17.3 1368

17.3 1369 * Monitor/Defibrillator Holder (NCE H7000) 560.28

17.3 1370 * What brand and model of Defibrillator will be used?

17.3 1371

17.3 1372 * "SmithWorks" IV Warmer (requires adding a 12V outlet - included in price) 699.93

17.3 1373 * Heat Pump for IV temp controlled interior cabinet (max. 8000 cubic inches) 2,875.11

17.3 1374 * Specify location for interior cabinet:

17.3 1375 * One set of Stryker Stainless Steel Cot Plates (one set = 3) 325.22

17.3 1376 * One set of Ferno Stainless Steel Cot Plates (one set = 3) 230.79

17.3 1377 * Stainless Steel Action Counter (flat sheet of stainless steel on action counter) 432.32

17.3 1378 * Stainless Steel Action Counter to be pan-formed 739.97

17.3 1379 * Stainless Steel back wall behind action counter 370.79

17.3 1380

17.3 1381 * Drill holes in doors made of polycarbonate for security break-away seals 92.30

17.3 1382 * Install "footman loops" on the following doors: 72.17

17.3 1383

17.3 1384 Location for shelf / shelves:

17.3 1385 * Additional adjustable shelf (.090" aluminum) 257.74

17.3 1386 * Additional adjustable shelf (.125" aluminum) 271.04

17.3 1387 * Fixed shelf within cabinet (.090" aluminum) 182.91

17.3 1388 * Fixed shelf within cabinet (.125" aluminum) 196.21

17.3 1389

17.3 1390 *Rubber mat for adjustable shelf (price per shelf) 50.72

17.3 1391

17.3 1392 Cabinet over Action Area to have…

17.3 1393 Sliding doors that are made of polycarbonate

17.3 1394 * Two vertically-hinged cabinet doors with latch (in lieu of sliding doors) 427.35

17.3 1395

17.3 1396 * Divide cabinet over Action Area into two equal size sections with an adjustable 625.24

17.3 1397 shelf in each section - with one door in each section as specified above.

17.3 1398 * Divide cabinet over Action Area into two equal size sections with an adjustable 1,004.36

17.3 1399 shelf in each section - with two doors in each section as specified above.

17.3 1400

17.3 1401 * Cabinet at head of squad bench for 166" module (available only w/ short R1) 705.04

17.3 1403 * The top of this cabinet will have: (select one of the following)

17.3 1404 Solid surface counter top 621.81

17.3 1405 Formica with one-inch lip and trim 251.90

17.3 1406 Stainless steel pan formed 1,110.76

17.3 1407 * Cabinet at the head of the squad bench will have two

17.3 1408 hinged door(s) with two adjustable shelves / shelf.

17.3 1410

17.3 1411 * Cabinet over squad bench (KKK requires 43+" between squad bench & cabinet) 773.22

17.3 1412 with dual sliding doors made of polycarbonate ("standard")

17.3 1413 * with a single set of sliding doors of polycarbonate (ILO dual sliding doors)

17.3 1414 * 2 horizontally-hinged cabinet doors of polycarbonate w/ gas shock hold-opens 256.06

17.3 1415 * Single horizontally-hinged cabinet door with gas-shock hold-opens 229.46

17.3 1416

17.3 1417 * Cabinet over CPR seat (half-depth) (KKK requires 43+" between seat & cabinet) 542.08

17.3 1418 with dual sliding doors made of polycarbonate ("standard")

17.3 1419 * with a single horizontally-hinged cabinet door with one gas-shock hold-open 141.33

17.3 1420

17.3 1421 * Cabinet w/ two drawers under pass-thru window on Type I 1,197.28

17.3 1422

17.3 1423 * Slide-out writing surface (with latch) below Action Area countertop 605.29

17.3 1424 Overall dimensions to be approx.: 16 D x 14 W x 3 H 0.00





17.3 1425 * Increase height of Action Area countertop (and L3/2 compartment) by 2 inches 121.38

17.3 1426 thereby reducing the cabinet over the Action Area by 2 inches

17.3 1427

17.3 1428 * Latching drawer below Action Area countertop to be locking 864.71

17.3 1429 * with a hinged writing lid made of polycarbonate set in top of the drawer 166.95

17.3 1430 Overall dimensions to be approx.: 18 D x 16 W x 3 H 0.00

17.3 1431 * Increase height of Action Area countertop (and L3/2 compartment) by 2 inches 121.38

17.3 1432

17.3 1433 Location for additional cabinet:

17.3 1434 * without restocking feature: state location (price per cabinet) 414.05

17.3 1441 * with restocking feature w/ hold open: state location (price per cabinet) 495.53

17.3 1458

17.3 1459 BIO-HAZARD / TRASH CONTAINERS:

17.3 1461 Select from the following options:

17.3 1462 Two wall mounted Maxxim kits - each kit has one sharps container and one trash container Standard

17.3 1463 One wall mounted Maxxim kit with sharp and trash containers (30.00)

17.3 1464 DELETE both wall mounted Maxxim kits (60.00)

17.3 1465 Maxxim kit(s) to be mounted by Excellance when customer picks up unit

17.3 1466 Maxxim kit(s) to be shipped loose with unit and mounted by customer

17.3 1467

17.3 1468 * Compartment in top of action area (L3/2 access) for sharps and trash - 708.40

17.3 1469 Trash with hinged, spring loaded polycarbonate lid; Sharps to be without lid.

17.3 1470

17.3 1471 * Recessed compartment without lid in front face of action area (with access 688.45

17.3 1472 in the L3/2 compartment) for Sharps and Trash

17.3 1473

17.3 1474 Specify Sharps or Trash:

17.3 1475 * Small tilt-out compartment front face of squad bench: 442.33

17.3 1476 * Compartment (open hole) front face of squad bench: 422.38

17.3 1477

17.3 1478 * Pull-out drawer with container in squad bench: size ? 804.86

17.3 1479

17.3 1480 * Shorten the curbside squad bench and install an access door for two 844.76

17.3 1481 one-gallon containers (one Sharps and one Trash). Each container will

17.3 1482 have its own hinged surface-mounted polycarbonate lid (one red and one clear,

17.3 1483 each with a knob) built into the access door. The access door will have a flush-

17.3 1484 mounted stainless steel key locking latch for container removal.

17.3 1485

17.3 1486 * Sage #8516-1H 5 quart Wall-mounted "Sharps" container with insert 118.72

17.3 1487 * #8513-1 disposable inserts for the above container 15.96

17.3 1488

17.3 1489 * Sage #8530-1H 3 gallon Wall-mounted "Sharps" container w/ insert 169.78

17.3 1490 * #8522-1R disposable inserts for the above container 19.54

17.3 1491

17.3 1492 * Non-sterile glove box holder option for either of above (#8550-LG) 41.16

17.3 1493

17.3 1494

17.3 1495 * The head-knocker over the side entry door shall provide storage for the 462.28

17.3 1496 * placement of the following number of glove boxes: 3

17.3 1497

17.3 1498 * The head-knocker over the rear entry door shall provide storage for the 462.28

17.3 1499 * placement of the following number of glove boxes: 3

17.3 1500

17.3 1501 * Excellance shall fabricate and mount an aluminum door caddy in the inside 863.03

17.3 1502 door panel of the side entry door which shall be capable of storing items such

17.3 1503 as paper towels, glove boxes, spray bottles and/or cleaning supplies.

17.3 1504

17.3 1505 * Recessed area (aluminum) for installing Sharps Container: Streetside wall 529.48

17.3 1506 * Recessed area (alum.) for installing Sharps Container: Face of Squad Bench 529.48





17.3 1507 * Recessed area (stainless) for installing Sharps Container: Streetside wall 809.83

17.3 1508 * Recessed area (s.s.) for installing Sharps Container: Face of Squad Bench 809.83

17.3 1520

17.3 1521 SEATING / UPHOLSTERY: OPTIONS

17.3 1523 Padded vinyl head protectors over module entryways, color coordinated to match interior standard

17.3 1524

17.3 1525 Select UPHOLSTERY color:

17.3 1526 Gray color for upholstery (Gray)

17.3 1527 * Dark Blue color for upholstery (Dark Blue)

17.3 1528 * Light Blue color for upholstery (Light Blue)

17.3 1529 * Maroon color for upholstery (Ruby)

17.3 1530 * Tan color for upholstery (Tan)

17.3 1531 * Earth tone color for upholstery (Mauve)

17.3 1532 * Special upholstery color (vendor/part #): 194.53

17.3 1533 * There is an upcharge for any special color of upholstery not listed above .

17.3 1534

17.3 1535 Net at head of Squad Bench, standard 58" x 17" size standard

17.3 1536 * DELETION CREDIT: Delete standard net at head of Squad Bench (193.07)

17.3 1537 * Custom net at head of Squad Bench, see specifications in Customer Notes 502.11

17.3 1538 * Padded fixed arm rest at head of squad bench 216.16

17.3 1539 * Removable feature for Padded Armrest at head of Squad Bench 184.59

17.3 1540 * Padded Mansaver with Hold-up Pin 418.15

17.3 1550

17.3 1551 FLOOR COVERING: OPTIONS

17.3 1553 Heavy duty vinyl floor covering will be installed inside patient compartment

17.3 1554 * Lonseal / Lonplate II flooring (this flooring will exte

excellance, inc. - ohioprocure.ohio.gov/pricelist/800579pricelist.pdf · 2017. 8. 22. · ohio...

Documents