ethernet & ieee 802.3 what the ieee standard covers- physical layer and interface to the link...
TRANSCRIPT
![Page 1: Ethernet & IEEE 802.3 What the IEEE standard covers- Physical layer and interface to the link layer. IEEE 802.2 is the Link layer standard. History- DEC/Intel/Xerox](https://reader035.vdocuments.us/reader035/viewer/2022062421/56649cee5503460f949bb43b/html5/thumbnails/1.jpg)
Ethernet & IEEE 802.3
What the IEEE standard covers- Physical layer andinterface to the link layer. IEEE 802.2 is the Link layer standard.
History- DEC/Intel/Xerox came up with it, then submitted toIEEE for standardization. Some changes were made soEthernet is not identical to IEEE 802.3
Differences between Ethernet and 802.3
There are some electrical and connector differences; most equipment uses IEEE 802.3.There is difference in the header. DIX uses TYPE, 802.3uses LENGTH. SInce the frame is limited in size, the two coexist.Most people use the DIX format.
![Page 2: Ethernet & IEEE 802.3 What the IEEE standard covers- Physical layer and interface to the link layer. IEEE 802.2 is the Link layer standard. History- DEC/Intel/Xerox](https://reader035.vdocuments.us/reader035/viewer/2022062421/56649cee5503460f949bb43b/html5/thumbnails/2.jpg)
IEEE & OSI
PHY
MAC
LLC 2
1
LLC = Logical Link ControlMAC = Media Access ControlPHY = Physical
![Page 3: Ethernet & IEEE 802.3 What the IEEE standard covers- Physical layer and interface to the link layer. IEEE 802.2 is the Link layer standard. History- DEC/Intel/Xerox](https://reader035.vdocuments.us/reader035/viewer/2022062421/56649cee5503460f949bb43b/html5/thumbnails/3.jpg)
Ethernet• Work started back in 1973 by Bob Metcalfe and David Boggs from Xerox Palo Alto
Research Center (PARC).
–He studied the Aloha network and "fixed" the mathematics.
• Experimental Ethernet implemented in 1975.
• Cooperative effort between Digital, Intel, and Xerox produced Ethernet Version 1.0 in 1980. –This also became known as the Blue Book specification or DIX standard. Ethernet V2.0 adopted in 1982.
• Ethernet was adopted with modifications by the standards committees IEEE 802.3 and ANSI 8802/3.
• Ethernet allows for only connectionless communication.
![Page 4: Ethernet & IEEE 802.3 What the IEEE standard covers- Physical layer and interface to the link layer. IEEE 802.2 is the Link layer standard. History- DEC/Intel/Xerox](https://reader035.vdocuments.us/reader035/viewer/2022062421/56649cee5503460f949bb43b/html5/thumbnails/4.jpg)
Normal Ethernet Operation
A
B
D
Data
C
Address mismatchpacket discarded
Address mismatchpacket discarded
Address matchpacket processed
Send datato node D
Transmitted packet seenby all stations on the LAN
(broadcast medium)
![Page 5: Ethernet & IEEE 802.3 What the IEEE standard covers- Physical layer and interface to the link layer. IEEE 802.2 is the Link layer standard. History- DEC/Intel/Xerox](https://reader035.vdocuments.us/reader035/viewer/2022062421/56649cee5503460f949bb43b/html5/thumbnails/5.jpg)
Ethernet Collisions
A
B C
D
Collision
Data transmission for A Data transmission for C
![Page 6: Ethernet & IEEE 802.3 What the IEEE standard covers- Physical layer and interface to the link layer. IEEE 802.2 is the Link layer standard. History- DEC/Intel/Xerox](https://reader035.vdocuments.us/reader035/viewer/2022062421/56649cee5503460f949bb43b/html5/thumbnails/6.jpg)
CSMA/CD"Carrier Sense/Multiple Access with Collision Detection"
"Driving in Boston"
BUS!
"Many stations; Listen before talking; listen while talking; if a collision,backoff and try again"
51.2 microseconds
![Page 7: Ethernet & IEEE 802.3 What the IEEE standard covers- Physical layer and interface to the link layer. IEEE 802.2 is the Link layer standard. History- DEC/Intel/Xerox](https://reader035.vdocuments.us/reader035/viewer/2022062421/56649cee5503460f949bb43b/html5/thumbnails/7.jpg)
CSMA/CD - A Simple Definition• A network station wishing to transmit will first check the cable plant to ensure that
no other station is currently transmitting (CARRIER SENSE).
• The communications medium is one cable, therefore, it does allow multiple stations access to it with all being able to transmit and receive on the same cable (MULTIPLE ACCESS).
• Error detection is implemented throughout the use of a station "listening" while it is transmitting its data.
–Two or more stations transmitting causes a collision (COLLISION DETECTION)
–A jam signal is transmitted to network by the transmitting stations that detected the collision, to ensure that all stations know of the collision. All stations will "backoff" for a random time.
–Detection and retransmission is accomplished in microseconds.
![Page 8: Ethernet & IEEE 802.3 What the IEEE standard covers- Physical layer and interface to the link layer. IEEE 802.2 is the Link layer standard. History- DEC/Intel/Xerox](https://reader035.vdocuments.us/reader035/viewer/2022062421/56649cee5503460f949bb43b/html5/thumbnails/8.jpg)
Frame/Packet Format
Preamble SFD Dst Src Type Data/Pad FCS
Size 7 1 6 6 2 46-1500 4(octets)
In IEEE 802.3, the Type field is used as a Length field.
Addresses are generally (3) octets vendor code, (3) octets device number.
![Page 9: Ethernet & IEEE 802.3 What the IEEE standard covers- Physical layer and interface to the link layer. IEEE 802.2 is the Link layer standard. History- DEC/Intel/Xerox](https://reader035.vdocuments.us/reader035/viewer/2022062421/56649cee5503460f949bb43b/html5/thumbnails/9.jpg)
Ethernet Addressing
Each station recognizes three classes of addresses.• Own address• Broadcast address (all 1's)• Optionally, one or more multicast addresses
Major reason for broadcast is address discovery.Multicast addresses are used for specialized link layer functions.
![Page 10: Ethernet & IEEE 802.3 What the IEEE standard covers- Physical layer and interface to the link layer. IEEE 802.2 is the Link layer standard. History- DEC/Intel/Xerox](https://reader035.vdocuments.us/reader035/viewer/2022062421/56649cee5503460f949bb43b/html5/thumbnails/10.jpg)
Ethernet Cable Names
RG-8 RG-58 22 - 26 AWG 62.5/125 micron10BASE5 10BASE2 10BASET 10BASEF
IEEE 802.3 IEEE 802.3a IEEE 802.3i
Name
Wire Type
IEEE Name
Standard Number
Other names
FiberUnshielded Twisted PairThin coaxialThick coaxial
N/A
Thick net Thin net UTP
![Page 11: Ethernet & IEEE 802.3 What the IEEE standard covers- Physical layer and interface to the link layer. IEEE 802.2 is the Link layer standard. History- DEC/Intel/Xerox](https://reader035.vdocuments.us/reader035/viewer/2022062421/56649cee5503460f949bb43b/html5/thumbnails/11.jpg)
Thick Coax Makeup
Jacket of PVC or Teflon
Thick braid for EMI
FoilThin braid for EMI
Thin foil bonded to insulation
Center conductor of tin plated solid copper conductor
Teflon is used forfire code regulations
![Page 12: Ethernet & IEEE 802.3 What the IEEE standard covers- Physical layer and interface to the link layer. IEEE 802.2 is the Link layer standard. History- DEC/Intel/Xerox](https://reader035.vdocuments.us/reader035/viewer/2022062421/56649cee5503460f949bb43b/html5/thumbnails/12.jpg)
Thick Coaxial Connection
Pierce clamp
Transceiver
Transceiver cable
Black marksevery 2.5 meters
to show transceiverplacement
500 meter maximum cable run
![Page 13: Ethernet & IEEE 802.3 What the IEEE standard covers- Physical layer and interface to the link layer. IEEE 802.2 is the Link layer standard. History- DEC/Intel/Xerox](https://reader035.vdocuments.us/reader035/viewer/2022062421/56649cee5503460f949bb43b/html5/thumbnails/13.jpg)
Transceivers• Transmitter/Receiver: AUI on one side, media on the other
• Used on all Ethernet networks and is the device that allows data to flow between the controller card and the network.
• Detects errors on the bus cable plant and reports them to the station's controller card.
• For thick coaxial cable, the transceiver is external to the controller card and attaches directly to the thick coaxial cable via a special cable known as the transceiver cable.
• External transceivers have a SQE function that enables the controller to determine the status of the transceiver.
• Usually has status indicators (LEDs) physically located on it to indicate the state of the transceiver (transmitting, receiving, collision, and power.)
![Page 14: Ethernet & IEEE 802.3 What the IEEE standard covers- Physical layer and interface to the link layer. IEEE 802.2 is the Link layer standard. History- DEC/Intel/Xerox](https://reader035.vdocuments.us/reader035/viewer/2022062421/56649cee5503460f949bb43b/html5/thumbnails/14.jpg)
Thin Coaxial Cable Makeup
Jacket made of PVC or Teflon
Polyethylene foam
Tinned copper wire
EMI braided shielding
![Page 15: Ethernet & IEEE 802.3 What the IEEE standard covers- Physical layer and interface to the link layer. IEEE 802.2 is the Link layer standard. History- DEC/Intel/Xerox](https://reader035.vdocuments.us/reader035/viewer/2022062421/56649cee5503460f949bb43b/html5/thumbnails/15.jpg)
Thin Coaxial Connection
T connector
Directconnection
to card
BNC connector at each cable end
Concatenation of network attachments
![Page 16: Ethernet & IEEE 802.3 What the IEEE standard covers- Physical layer and interface to the link layer. IEEE 802.2 is the Link layer standard. History- DEC/Intel/Xerox](https://reader035.vdocuments.us/reader035/viewer/2022062421/56649cee5503460f949bb43b/html5/thumbnails/16.jpg)
Thin Coaxial Connection (cont.)
Interface to computer bus
T connector for connection to cable plant
transceiver logicOn-board
BNC connector
AUI connector
02608C
ASIC
![Page 17: Ethernet & IEEE 802.3 What the IEEE standard covers- Physical layer and interface to the link layer. IEEE 802.2 is the Link layer standard. History- DEC/Intel/Xerox](https://reader035.vdocuments.us/reader035/viewer/2022062421/56649cee5503460f949bb43b/html5/thumbnails/17.jpg)
UTP Makeup• UTP was standardized by the IEEE 802.3 committee in October of 1990.
• Standardized by the EIA under TIA 568A.
• UTP for LANs is now classified as:
–Category 3 - used for LANs up to 10 Mbps.–Category 4 - used for LANs up to 16 Mbps.–Category 5 - used for LANs up to 100 Mbps.
• Cable is made up of 8 strands of 24 AWG wire.–Only 2 pair are used for single 10BASET connection.
![Page 18: Ethernet & IEEE 802.3 What the IEEE standard covers- Physical layer and interface to the link layer. IEEE 802.2 is the Link layer standard. History- DEC/Intel/Xerox](https://reader035.vdocuments.us/reader035/viewer/2022062421/56649cee5503460f949bb43b/html5/thumbnails/18.jpg)
Unshielded Twisted Pair
Unshielded twisted pairatleast two (2) twists per foot
RJ-45Connector
RJ-45connector
100m max cable run
8 pin 8 pin
Unshielded twisted pair cable
Straight through pins 1, 2, 3 and 6
Repeater unit required
![Page 19: Ethernet & IEEE 802.3 What the IEEE standard covers- Physical layer and interface to the link layer. IEEE 802.2 is the Link layer standard. History- DEC/Intel/Xerox](https://reader035.vdocuments.us/reader035/viewer/2022062421/56649cee5503460f949bb43b/html5/thumbnails/19.jpg)
Concentrator (Hub) Management• With the concentration of the wiring into a common point, network managers can manage the hub with specialized
software.
• Network management software resides not only in the concentrator but on an external workstation’s device (a PC, for example).
– The workstation can query the concentrator for information.
• Concentrators also allow the control of individual ports.
• This software allows managers to extract information from each card that is inserted in the repeater. You could query the hub for statistics such as:
– number of packets (bytes),
– number of collisions (single and multiple),
– number of framing errors,
– number of time the particular card de-inserted itself from the network,
– ability to turn on/off any repeater card in the hub, and
– all information is time and date stamped.
• With 10BASET, all information is provided on an individual-connection basis, giving a manager information right from the desktop.
![Page 20: Ethernet & IEEE 802.3 What the IEEE standard covers- Physical layer and interface to the link layer. IEEE 802.2 is the Link layer standard. History- DEC/Intel/Xerox](https://reader035.vdocuments.us/reader035/viewer/2022062421/56649cee5503460f949bb43b/html5/thumbnails/20.jpg)
Ethernet Repeaters• Extend the network by interconnecting multiple segments
–Extend the physical domain of the network
• Governed by the IEEE 802.3c working group standard.
–This governs the electrical specifications of a repeater.–The physical configurations of a repeater varied from vendor to vendor.
• Some repeaters contain the intelligence to:
–detect collisions per cable plant (will not repeat collision fragments to other cable plants).
–de-insert themselves from a wiring concentrator (when there are excessive errors on the cable plant).
– submit network management information to a central controller.
• Repeaters have been transformed into wiring concentrators or hubs
• Repeaters can be used to interconnect different wiring types but not different access methods (i.e., not Token Ring to Ethernet).
![Page 21: Ethernet & IEEE 802.3 What the IEEE standard covers- Physical layer and interface to the link layer. IEEE 802.2 is the Link layer standard. History- DEC/Intel/Xerox](https://reader035.vdocuments.us/reader035/viewer/2022062421/56649cee5503460f949bb43b/html5/thumbnails/21.jpg)
IEEE802.3 Efficiency
"WARNING: Opinion"
% Utilization Status
0 - 10 Great!
10 - 40 OK
40 - 60 Performance Problems -- look at it
60+ RIP
Time
SignalOn
"Utilization"