et entertainment subaru wrx

7/25/2019 ET Entertainment Subaru wrx

1/12

ENTERTAINMENT


2/12ET-2

ENTERTAINMENTGENERAL DESCRIPTION

1. General Description

A: CAUTION Before disassembling or reassembling parts, al-ways disconnect the battery ground cable. Whenreplacing radio, control module, and other partsprovided with memory functions, record memory

contents before disconnecting the battery groundcable. Otherwise, the memory will be erased. Reassemble in reverse order of disassembly, un-less otherwise indicated. Adjust parts to the given specifications. Connect the connectors and hoses securely dur-ing reassembly. After reassembly, make sure functional parts op-erate smoothly.

B: PREPARATION TOOL

1. GENERAL TOOLS

TOOL NAME REMARKS

Circuit TesterUsed for measuring resis-

tance and voltage.

Conductive Silver Composi-

tion

(DUPONT No. 4817 or

equivalent)

Used for repairing antenna

wire.


3/12ET-3

ENTERTAINMENTRADIO SYSTEM

2. Radio System

A: SCHEMATIC

B: INSPECTION

Symptom Repair order

No power coming in. (No display and no sound from speakers) (1) Check the fuse and power supply for radio.(2) Check the radio ground.

(3) Remove the radio for repair.

A specific speaker does not operate. (1) Check the speaker.

(2) Check the output circuit between radio and speaker.

Radio generates noise with engine running. (1) Check the radio ground.

(2) Check the generator.

(3) Check the ignition coil.


AM and FM modes are weak or noisy. (1) Check the antenna.

(2) Check the antenna amplifier.

(3) Check the noise suppressor.

(4) Check the radio ground.



4/12ET-4

ENTERTAINMENTFRONT ACCESSORY POWER SUPPLY SOCKET SYSTEM

3. Front Accessory Power Sup-ply Socket System

A: SCHEMATIC


5/12ET-5

ENTERTAINMENTRADIO BODY

4. Radio Body

A: REMOVAL1) Disconnect the ground cable from battery.2) Remove the center panel while disconnectingconnector.

3) Remove the fitting screws, and slightly pull outthe radio from center console.

4) Disconnect the harness connectors and antennafeeder cord.

B: INSTALLATIONInstall in the reverse order of removal.

(A) Hook pawl

ET-00076: (A)

ET-00077


6/12ET-6

ENTERTAINMENTFRONT SPEAKER

5. Front Speaker

A: REMOVAL1) Disconnect the ground cable from battery.2) Remove the front door trim. 3) Remove the front speaker mounting screws.

4) Disconnect the harness connector and remove

front speaker.B: INSTALLATIONInstall in the reverse order of removal.

ET-00072


7/12ET-7

ENTERTAINMENTTWEETER

6. Tweeter

A: REMOVAL

1) Disconnect the ground cable from battery.2) Remove the front door trim. 3) Remove the tweeter mounting screws.


tweeter.B: INSTALLATION

Install in the reverse order of removal.

ET-00053


8/12ET-8

ENTERTAINMENTREAR SPEAKER

7. Rear Speaker

A: REMOVAL1) Disconnect the ground cable from battery.2) Remove the rear door trim. 3) Remove the rear speaker mounting screws.


rear speaker.B: INSTALLATIONInstall in the reverse order of removal.

ET-00073


9/12ET-9

ENTERTAINMENTANTENNA

8. Antenna

A: INSPECTION

Measure the resistance between antenna terminaland each antenna wire.If an antenna wire is OK, resistance will be lessthan 1 . If an antenna wire is broken, the resis-

tance will be more than 1 M

.NOTE:When checking the continuity, wind a piece of alu-minum foil around the tip of tester probe, and thenpress the aluminum foil against wire with your fin-ger.

To locate the broken point, move the probe alongantenna wire.

B: REPAIR

1) Clean the antenna wire and surrounding areawith a cloth dampened by alcohol.2) Paste a thin masking film on the glass along bro-ken wire.3) Deposit conductive silver composition (DU-PONT No. 4817) on the broken portion with a draw-

ing pen.

4) Dry out the deposited portion.5) After repair has been completed, measure theresistance in repaired wire.

(A) Tester probe

(B) Aluminum foil

(C) Antenna wire

ET-00007

(B)

(C)

(A)

ET-00008

(A) Broken portion

(B) Masking film

(C) Conductive silver composition

(B)

(C)

ET-00009

(A)


10/12ET-10

ENTERTAINMENTANTENNA AMPLIFIER

9. Antenna Amplifier

A: REMOVAL

1. SEDAN

1) Disconnect the ground cable from battery.2) Remove the rear pillar upper trim. 3) Disconnect the harness connector and terminal.4) Remove the mounting screws and detach anten-na amplifier.

2. WAGON

1) Disconnect the ground cable from battery.2) Remove the rear quarter upper trim and rooftrim. 3) Disconnect the harness connector and terminal.4) Remove the mounting screws and detach theantenna amplifier.


C: INSPECTIONMeasure the antenna amplifier resistance. SEDAN

WAGON

ET-00058

ET-00059

Terminal No. Standard

1-a and Amplifier body More than 100 k

1-b and Amplifier body Less than 1 2-a and Amplifier body More than 100 k

3 and Amplifier body More than 100 k

4-a and Amplifier body More than 100 k

4-b and Amplifier body Less than 1

ET-00074

(3)

(1) (1)-a(2)-a

(1)-b

(2)

ET-00062

(1)-a

(2)-a

(1)-b

(1)

(4)

(2)(4)-a

(4)-b


11/12ET-11

ENTERTAINMENTNOISE SUPPRESSOR

10.Noise Suppressor

A: REMOVAL

1. SEDAN

1) Disconnect the ground cable from battery.2) Remove the rear pillar upper trim. 3) Remove the rear shelf trim. 4) Disconnect the feeder cord connector from an-tenna amplifier.5) Disconnect the harness connector of noise sup-pressor from terminal on glass antenna.6) Remove the harness clip.7) Remove the mounting nut and detach the noisesuppressor.

2. WAGON

1) Disconnect the ground cable from battery.2) Remove the rear gate trim. 3) Disconnect the connector from noise suppres-sor.4) Remove the mounting nut and detach the noisesuppressor.


ET-00063

ET-00064


12/12ET 12

ENTERTAINMENTFRONT ACCESSORY POWER SUPPLY SOCKET

11.Front Accessory Power Sup-ply Socket

A: REMOVAL1) Disconnect the ground cable from battery.2) Remove the center panel.

3) Disconnect the harness connectors and removefront accessory power supply socket.


ET-00065

et entertainment subaru wrx

Documents