error messages - cisco · error messages - cisco ... eid-6017

Error Messages

The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These termsdo not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration.Rather, these terms, as well as "Path Protected Mesh Network" and "PPMN," refer generally to Cisco'spath protection feature, which may be used in any topological network configuration. Cisco does notrecommend using its path protection feature in any particular topological network configuration.

Note

This chapter lists the error messages for the Cisco . The error dialog box in Figure 1: Error Dialog Box, onpage 1 consists of three parts: the error title, error ID, and error message.

Figure 1: Error Dialog Box

• Error Messages Reference, page 1

Error Messages ReferenceTable 1: Error Messages, on page 2 gives a list of all error or warning message numbers, the messages, anda brief description of each message. The table lists two types of messages: error messages (EID-nnnn) andwarning messages (WID-nnnn). Error messages are alerts that an unexpected or undesirable operation hasoccurred that either indicates the risk of loss of traffic or an inability to properly manage devices in the network.Warnings are alerts that the requested operation could lead to an error.Warnings are sometimes used to conveyimportant information.

Cisco ONS 15454 DWDM Troubleshooting Guide, Release 9.6.x 78-20789-02 1

Table 1: Error Messages

DescriptionError/Warning MessageError/WarningID

The error ID is invalid.Invalid error ID.EID-0

Cisco Transport Controller (CTC)encountered a null pointer in the areadescribed by the specified item.

A null pointer encountered in {0}.EID-1

Refer to the error message text.The host name of the network element cannot beresolved to an address.

EID-1000

Refer to the error message text.Unable to launch CTC due to applet securityrestrictions.

Please review the installation instructions to make surethat the CTC launcher is given the permissions it needs.

Note that you must exit and restart your browser inorder for the new permissions to take effect.

EID-1001

The node is not reachable from CTCclient station.

The host name (e.g., for the network element) wassuccessfully resolved to its address, but no route canbe found through the network to reach the address.

EID-1002

Unexpected exception or error whilelaunching CTC from the applet.

An error was encountered while attempting to launchCTC. {0}

EID-1003

Unable to delete the CTC cachedJARs, because another applicationmay have the JAR files running; forexample, another instance of CTC.

Problem Deleting CTC Cache: {0} {1}EID-1004

CTC encountered an error whilewriting to log files, preference files,etc.

An error occurred while writing to the {0} file.EID-1005

The URL used to download thespecified JAR file is incorrect.

The URL used to download {0} is malformed.EID-1006

An input or output exception wasencountered when CTC tried todownload the specified JAR file.

An I/O error occurred while trying to download {0}.EID-1007

The password is invalid.Password shall not contain the associated user-ID.EID-1018

CTC could not create the file due toan invalid filename.

Could not create {0}. Please enter another filename.EID-1019

Cisco ONS 15454 DWDM Troubleshooting Guide, Release 9.6.x2 78-20789-02

Error MessagesError Messages Reference


CTC was unable to switch from thenode or card view to the network viewand is now shutting down.

Fatal exception occurred, exiting CTC. Unable toswitch to the Network view.

EID-1020

CTC was unable to display therequested view (node or network).

Unable to navigate to {0}.EID-1021

Refer to the error message text.An IOS session cannot be opened right now with thisslot. Most likely someone else (using a different CTC)already has a session opened with this slot. Please tryagain later.

EID-1022

Refer to the error message text.This IOS session has been terminated. Terminationsare caused when the session has timed out, the cardresets, there is already a session with the slot, orpassword configuration is required.

EID-1023

CTC was unable to create the helpbroker for the online help.

Unable to create Help Broker.EID-1025

CTC encountered an error in theonline help file.

Error found in the Help Set file.EID-1026

CTC was unable to locate the contentfor the help ID.

Unable to locate help content for Help ID: "{0}".EID-1027

There was an error while saving thespecified table.

Error saving table. {0}EID-1028

Refer to the error message text.CTC cannot locate the online user manual files. Thefiles may have been moved, deleted, or not installed.To install online user manuals, run the CTC installationwizard on the software or documentation CD.

EID-1031

Refer to the error message text.CTC cannot locate Acrobat Reader. If Acrobat Readeris not installed, you can install the Reader using theCTC installation wizard provided on the software ordocumentation CD.

EID-1032

Refer to the error message text.CTC experienced an I/O error while working with thelog files. Usually this means that the computer has runout of disk space. This problem may or may not causeCTC to stop responding. Ending this CTC session isrecommended, but not required.

EID-1035

Refer to the warning message text.WARNING: Deleting the CTC cache may cause anyCTC running on this system to behave in an unexpectedmanner.

WID-1036




Invalid file name. CTC is unable toopen the specified file. Ensure that thefile exists and the filename was typedcorrectly.

Could not open {0}. Please enter another filename.EID-1037

The specified file does not exist.The file {0} does not exist.EID-1038

Refer to the error message text.The version of the browser applet does not match theversion required by the network element. Please closeand restart your browser in order to launch the CiscoTransport Controller.

EID-1039

CTC encountered an error whileclosing the specified connection.

An error occurred while closing the {0} connection.WID-1041

Refer to the warning message text.You have selected Java version {0}. This version isoutside of the recommended range and may cause anunpredictable behavior of the software. Do you wishto continue?

WID-1042

Check for possible causes and tryagain.

Error writing to file: {0}. This might be caused by adirectory permission, quota or disk volume full issue.

EID-1043

Refer to the warning message text.Warning: there is a discrepancy in the build timestampbetween the NE cached jar file ({0}) and the NE ({1}).Your CTC jar cache should be emptied.

WID-1044

The CTC software version must begreater than or equal to the softwareversion on the node being managed.

Selected CTC version ({0}) must be greater than orequal{to the login NE version ({1}).

EID-1046

Refer to the error message text.No additional Pseudo IOS windows may be opened atthis time. The maximum number of Pseudo IOSwindows are open.

EID-1047

Refer to the error message text.This Pseudo IOS connection has been terminated.Terminations are caused when the session has timedout, the node resets, or when the exit command hasbeen invoked.

This may also occur when the maximum number ofconcurrent Pseudo IOS connections has been reached.

EID-1048

Refer to the error message text.A Pseudo IOS connection cannot be opened right nowon this node. Please try again later.

EID-1049

Refer to the error message text.Connection failed on node {0}EID-1050




No rolls were selected for the bridgeand roll.

No rolls were selected. {0}EID-2001

You cannot delete the roll unless ithas been completed or cancelled.

The roll must be completed or canceled before it canbe deleted.

EID-2002

There was an error when CTC triedto delete the roll.

An error occurred while deleting the roll. {0}EID-2003

You did not select a Cisco IOS slot.No Cisco IOS slot was selected.EID-2004

CTC cannot find the online help filesfor the specified window. The filesmight have been moved, deleted, ornot installed. To install online help,run the setup program on the softwareCD.

CTC cannot find the online help files for {0}. The filesmight have been moved, deleted, or not installed. Toinstall online help, run the setup program on thesoftware CD.

EID-2005

An error occurred when CTC tried toopen the circuit for editing.

An error occurred while editing the circuit(s). {0} {1}.EID-2006

CTC cannot save the preferences.The preferences could not be saved.EID-2007

CTC cannot find the file needed tosave the circuit preferences.

The circuit preferences could not be saved: {0}EID-2008

Refer to the error message text.CTC was unable to download the package: {0}EID-2009

CTC could not delete the destination.An error occurred while deleting the destination.EID-2010

CTC could not destroy the circuit.The circuit could not be destroyed.EID-2011

CTC could not reverse the circuitdestroy.

The reverse circuit could not be destroyed.EID-2012

Refer to the error message text.The circuit creation failed. The circuit creation cannotproceed due to changes in the network which affectedthe circuit(s) being created. The dialog box will close.Please try again.

EID-2013

You must select a circuit to completethis function.

No circuit(s) were selected. {0}EID-2014

Youmust delete the rolls in the circuitbefore deleting the circuit itself.

The circuit {0} cannot be deleted because it has one ormore rolls.

EID-2015

CTC could not delete the tunnel asthere are circuits that use the tunnel.

The circuit deletion failed.EID-2016




There was an error mapping thecircuit.

An error occurred while mapping the circuit. {0}EID-2017

There was a failure in circuit roll.Change the circuit state toDISCOVERED and proceed.

The circuit roll failed. The circuit must be in theDISCOVERED state in order to perform a roll.

EID-2018

Refer to the error message text.The circuit roll failed. Bridge and roll is not supportedon DWDM circuits.

EID-2019

Refer to the error message text.The circuit roll failed. The two circuits must have thesame direction.

EID-2020

Refer to the error message text.The circuit roll failed. The two circuits must have thesame size.

EID-2021

Refer to the error message text.The circuit roll failed. A maximum of two circuits canbe selected for a bridge and roll operation.

EID-2022

Refer to the error message text.CTC was unable to create a new user account.EID-2023

There was an error during nodeselection.

An error occurred during node selection.EID-2024

Refer to the error or warning messagetext. For example, this error isgenerated from the node viewProvisioning> WDM-ANS> tabs toindicate that the selected ring type isnot supported by the endpoints of thecircuit. Another example is theProvisioning> VLAN tabs in cardview (Ethernet card only), where itindicates that the back-end spanningtree protocol (STP) disabling is notsupported.

This feature cannot be used. Verify that each endpointof this circuit is running software that supports thisfeature.

EID-2025

Error occurred while attempting toswitch a path protection circuit awayfrom a span.

The {0} request could not be applied. {1}EID-2026

CTC could not delete the circuit drop.An error occurred while deleting the circuit drop.EID-2027

CTC could not remove the circuitnode.

An error occurred while removing the circuit node.EID-2028

The task you are trying to complete isnot supported by CTC.

The requested operation is not supported.EID-2029




There was an error duringprovisioning.

An error occurred during provisioning.EID-2030

There was an error while adding anode.

An error occurred while adding the node.EID-2031

CTC could not rename the circuit.The circuit could not be renamed. {0}EID-2032

There was an internal error whilevalidating the user changes after theApply button was pressed. This errorcan occur in the Edit Circuit dialogbox or in the BLSR table in the shelfview (rare condition).

An error occurred during validation. {0}EID-2033

Refer to the error message text.Network circuits could not be added: {0}EID-2034

Refer to the error message text.The source and destination nodes are not connected.EID-2035

You cannot delete the DCC/GCC linkas it is needed to access the node.

The {0} cannot be deleted. LAN Access has beendisabled on this node and this {0} is needed to accessthe node.

EID-2036

CTC cannot find an attribute for thespecified item.

The attribute for {0} cannot be found.EID-2037

The protection operation you tried toexecute is invalid.

The protection operation is invalid.EID-2038

You must select a node beforeperforming the task.

Please select a node first.EID-2040

You must select a link that has pathsavailable.

No paths are available on this link. Please make anotherselection.

EID-2041

Refer to the error message text.This span is not selectable. Only the green spans withan arrow may be selected.

EID-2042

Refer to the error message text.This node is not selectable. Only the source node andnodes attached to included spans (blue) are selectable.Selecting a selectable node will enable its availableoutgoing spans.

EID-2043

You must select only one link goingin and out of a node. Selecting morethan one link is contradictory to thepath selection algorithm.

This link may not be included in the required list.Constraints only apply to the primary path. Each nodemay have a maximum of one incoming signal and oneoutgoing link.

EID-2044




Refer to the error message text.This link may not be included in the required list. Onlyone outgoing link may be included for each node.

EID-2045

There was an error due to an invalidslot number.

Please enter a valid value for the slot number.EID-2047

There was an error due to an invalidport number.

Please enter a valid value for the port number.EID-2048

CTC could not destroy the newcircuit.

The new circuit could not be destroyed.EID-2050

The specified circuit cannot bedowngraded.

The circuit cannot be downgraded. {0}EID-2051

There was an error during the circuitprocessing.

An error occurred during circuit processing.EID-2052

There was an error during theendpoint selection.

An error occurred while selecting an endpoint.EID-2054

This error occurs in the circuitcreation dialog only during a racecondition that has incorrectly allowedentities without endpoints to bedisplayed in the combination boxes.

No endpoints are available for this selection. Pleasemake another selection.

EID-2055

An internal error occurred in NetworkAlarm tab while synchronizing alarmswith the nodes.

A communication error occurred: {0}EID-2056

There was an error during the nodedeletion.

An error occurred while deleting the node. {0}EID-2059

CTC could not find any protectionchannel access (PCA) circuits for thistask.

No PCA circuits were found.EID-2060

There was an error defining theVLAN.

An error occurred while provisioning the VLAN.EID-2061

Refer to the error message text.An error occurredwhile deletingVLANs. NoVLAN(s)were selected. Please select a VLAN.

EID-2062

The selected VLAN is the defaultVLAN and cannot be deleted.

The default VLAN cannot be deleted.EID-2063




There was an error deleting thespecified VLAN.

An error occurred while deleting VLANs. {0}EID-2064

Cannot import the profile because theprofile has reached the maximumnumber of copies in the editor.

The profile cannot be imported. The profile "{0}" existsin the editor and the maximum number of copies (ten)exists in the editor. The import will be aborted. Theprofile has already been loaded eleven times.

EID-2065

CTC encountered an error whiletrying to store the profile.

The profile could not be stored. An error occurred whilewriting to {0}.

EID-2066

CTC encountered an error whilewriting the specified file.

An error occurred while writing to the file. {0}EID-2067

CTC encountered an error trying toload the alarm profile from the node.

The alarm profile could not be loaded from the node.EID-2068

Either the specified file was not found,or there was an input/outputexception.

The file could not be found or an I/O exceptionoccurred. {0}

EID-2069

There was a failure in deleting thespecified profile.

The profile could not be deleted. {0}EID-2070

You cannot select more than onecolumn during clone action.

Only one column may be highlighted.EID-2071

You cannot select more than oneprofile.

Only one profile may be highlighted.EID-2072

You cannot delete a permanentcolumn.

This column is permanent and cannot be removed.EID-2073

You have not selected any profile orcolumn. Reset operation is done byright-clicking the selected column.

Select one or more profiles.EID-2074

A permanent column cannot be reset.This column is permanent and cannot be reset.EID-2075

You cannot rename a permanentcolumn.

This column is permanent and cannot be renamed.EID-2077

You cannot compare two profilesunless you select two columns.

At least two columns must be highlighted.EID-2078




Refer to the error message text.The alarm types cannot be loaded into table. There areno reachable nodes from which the list of alarm typescan be loaded. Please wait until such a node is reachableand try again.

EID-2079

The specified node does not have anyprofiles.

The node {0} has no profiles.EID-2080

There was an error while removingthe specified profile from the specifiednode.

An error occurred while removing profile {0} from thenode {1}.

EID-2081

CTC cannot find the specified profilefrom the specified node.

The profile {0} does not exist on the node {1}.EID-2082

There was an error adding thespecified profile to the specified node.

An error occurred while adding profile {0} to the node{1}.

EID-2083

You tried to select an invalid profile.Select another profile.

The profile selection is invalid. No profiles wereselected.

EID-2085

You tried to select an invalid node.Select another node.

The node selection is invalid. No nodes were selected.EID-2086

Refer to the error message text.No profiles were selected. Please select at least oneprofile.

EID-2087

The profile name cannot be empty.The profile name is invalid.EID-2088

Select a unique name.Too many copies of {0} exist. Please choose anothername.

EID-2089

You must select one or more nodeson which you can store the profile.

No nodes were selected. Please select the node(s) onwhich to store the profile(s).

EID-2090

CTC is unable to switch to thespecified node.

Unable to switch to the node {0}.EID-2091

CTC encountered a general exceptionerror while trying to complete the task.

A general exception error occurred.EID-2092

The name must have a minimum ofsix characters.

The name is too short. It does not have enoughcharacters. {0}

EID-2093

You must make sure the two fieldshave the same password.

The password and confirmed password fields do notmatch.

EID-2094




The password you entered is notallowed.

The password is invalid. {0}EID-2095

You must have an assigned securitylevel to perform this task.

The user must have a security level.EID-2096

You did not specify a user name.No user name was specified.EID-2097

There was an error during the ringswitch.

An error occurred while ring switching.EID-2099

You have not selected the profile todelete.

Please select at least one profile to delete.EID-2100

There was an error during theprotection switching.

An error occurred while protection switching.EID-2101

The forced switch could not beremoved for some circuits. You mustswitch these circuits manually.

The forced switch could not be removed for somecircuits. You must switch these circuits manually.

EID-2102

There was an error during the spanupgrade.

An error occurred while upgrading the span.EID-2103

This error occurs during the pathprotection span upgrade procedure.

The circuits cannot be switched back because one orboth nodes are not reachable.

EID-2104

You must supply a name for the node.The node name cannot be empty.EID-2106

There was an error adding thespecified item.

An error occurred while adding {0}. The host isunknown.

EID-2107

The specified item exists in thenetwork.

{0} is already in the network.EID-2108

The node you are trying to add isalready present in the current logingroup.

The node is already in the current login group.EID-2109

You must enter a number in the rangebetween 0 and the specified value.

Please enter a number between 0 and {0}.EID-2110

Select a node ID that is not in use.This node ID is already in use. Please choose another.EID-2111

CTCcannot set theBLSR/MS-SPRingextension byte.

The extension byte for the ring cannot be set. {0}EID-2113




This error can occur during an attemptto apply a BLSR protection operationto a line.

A card communication failure occurred during theoperation.

EID-2114

There was an error in applying thespecified operation.

An error occurred during the operation. {0}EID-2115

The extension byte set for thespecified ring is invalid.

The extension byte setting for the ring is invalid. {0}EID-2116

Clear all the protection operations forthe ring before deleting it.

The ring cannot be deleted. A protection operation isset. All protection operations must be clear for ring tobe deleted.

EID-2118

Clear all protection operations orswitches before deleting the ring.

{0} cannot be deleted because a protection switch isin effect. Please clear any protection operations, ensurethat the reversion time is not "never" and allow anyprotection switches to clear before trying again.

EID-2119

The specified nodes could not beunprovisioned. Try deleting thisBLSR or MS-SPRing later.

The following nodes could not be unprovisioned {0}Therefore you will need to delete this {1} again later.

EID-2120

CTC cannot upgrade the specifiedring.

The ring cannot be upgraded. {0}EID-2121

You have selected an incorrect ringspeed for upgrade. Only rings withinthe specified parameters can beupgraded to 4-fiber BLSR.

The ring speed for is inadequate for the upgradeprocedure. Only {0} (or higher) {1} can be upgradedto four-fiber.

EID-2122

Nonupgradable nodes. Verify that thespecified nodes have at least twoIS-NR ports with the same speed asthe 2-fiber BLSR. The specified portscannot serve as a timing reference,and they cannot have datacommunications channel (DCC)terminations or overhead circuits.

Verify that the following nodes have at least twoin-service ports with the same speed as the two-fiber{0}. The ports cannot serve as timing references, andthey cannot have DCC terminations or overheadcircuits. {1}

EID-2123

Refer to the error message text.You cannot add this span because it is connected to anode that already has the east and west ports defined.

EID-2124

Refer to the error message text.You cannot add this span as it would cause a singlecard to host both the east span and the west span. Acard cannot protect itself.

EID-2125




There is an Open Shortest Path First(OSPF) area error.

An error occurred while provisioning the OSPF area.{0}

EID-2126

A circuit cannot occupy different STSregions on different spans. You mayadd a different span or delete thespecified circuit.

You cannot add this span. It would cause the followingcircuit(s) to occupy different {0} regions on differentspans: {1}

Either select a different span or delete the abovecircuit(s).

EID-2127

An internal error occurred whiletrying to remove a span from a BLSR.

This alarm occurs in the network-levelBLSR creation dialog box.

The state is invalid.EID-2128

Refer to the error message text.You cannot use same slot for east and west protectports.

EID-2129

Enter a ring ID value between 0 and9999.

The ring ID value, {0}, is not valid. Please enter a validnumber between 0 and 9999.

EID-2130

You must select another reversiontype.

The reversion cannot be set to INCONSISTENT.EID-2131

Input/Output error. Unable to storeoverhead circuit preferences.

The overhead circuit preferences could not be stored:{0}

EID-2135

There was an error while merging thecircuits.

An error occurred during the circuit merge. {0}EID-2137

Refer to the error message text.Not all destinations could be deleted. Please try again.EID-2138

There was an error in updating thecircuit destinations.

An error occurred while updating the destinations.EID-2139

Select the version of online help, andproceed.

No online help version was selected. The online helpbook cannot be deleted.

EID-2143

You cannot delete the specified onlinehelp.

An error occurred while deleting the online helpbook(s). {0}

EID-2144

Refer to error message.No nodes appear to have a Cisco IOS card.EID-2145

You cannot logout of an account otherthan your own.

This is a security violation. You may only logout ofyour own account.

EID-2146

You cannot change an account otherthan your own.

This is a security violation. You may only change yourown account.

EID-2147




You cannot delete the account you arecurrently logged in.

This is a security violation. You cannot delete theaccount under which you are currently logged in.

EID-2148

Refer to the error message text.There is no exportable content in this view.WID-2149

Wait till the specified node isinitialized and try again.

The node {0} is not initialized. Please wait and tryagain.

WID-2150

Refer to the warning message text.Spanning tree protection is being disabled for thiscircuit.

WID-2152

Refer to the warning message text.Adding this drop will make the circuit a PCA circuit.WID-2153

Refer to the warning message text.Monitor circuits cannot be created on a port groupingcircuit.

WID-2154

The specified nodes do not supportswitch counts completely.

Switch counts might not be fully supported on somenodes. {0}

WID-2155

Refer to the warning message text.The manual roll mode is recommended for dual rolls.For auto dual rolls, please verify that roll to facilitiesare in service and error-free.

WID-2156

CTC could not complete the rollbecause the roll is destroyed, in anincomplete state, in a TL1_roll state,is cancelled, or is not ready tocomplete.

The roll(s) cannot be completed. {0}WID-2157

There are two roll modes: auto andmanual. For a one-way circuit sourceroll, the roll mode must be auto andfor a one- way circuit destination roll,the roll mode must be manual.

The roll mode is invalid. {0}EID-2158

The roll is not ready for completion.The roll is not ready for completion. {0}EID-2159

Refer to error message text.The roll is not connected. {0}EID-2160

One of the rolls is not completed forthe dual roll. If it is auto roll, it willbe completed when a valid signal isdetected. If it is a manual roll, youmust complete the roll from CTC ifBridge and Roll is operated fromCTC, or from TL1 if Bridge and Rollis operated from TL1.

The sibling roll is not complete. {0}EID-2161




Refer to the error message text.An error occurred during roll acknowledgement. {0}EID-2162

CTC cannot cancel the roll.The roll cannot be canceled. {0}EID-2163

CTC encountered a roll error.An error occurred during the roll. {0}EID-2164

Repair the circuits that originate fromor drop at the specified node, with thenew MAC address.

The MAC address of the node {0} has been changed.All circuits originating from or dropping at this nodewill need to be repaired.

WID-2165

Initialize the node and proceed.The node cannot be inserted into the domain becauseit is not initialized.

WID-2166

You do not have the privilege toperform this action.

You have insufficient security privileges to performthis action.

WID-2167

CTC encountered warnings whileloading the alarm profile import file.

The following warnings surfaced while loading {0}.{1}

WID-2168

The profile selected does not exist onthe node. Select another profile.

One or more of the profiles selected do not exist onone or more of the nodes selected.

WID-2169

The number of profile that can existon a node has reached the limit. Toadd a profile, delete any of theexisting profiles.

The profile list on node {0} is full. Please delete oneor more profiles if you wish to add the profile. {1}

WID-2170

Refer to the warning message text.You have been logged out. Click OK to exit CTC.WID-2171

The Internet Inter-ORB Protocol(IIOP) listener port setting for theCTCCommonObject Request BrokerArchitecture (CORBA)will be appliedon the next CTC restart.

The CTC CORBA (IIOP) listener port setting of {0}will be applied on the next CTC restart.

WID-2172

Select an alternate port, as the currentport is either in use or you do not haveenough permission on it.

The port is unavailable. The desired CTC CORBA({0}) listener port, {1}, is already in use or you do nothave permission to listen on it. Please select an alternateport.

EID-2173

You entered an invalid firewall portnumber. Try again.

An invalid number was entered. Please check it and tryagain.

EID-2174

There is a mismatch with theextension byte.

An extension byte mismatch occurred. {0}WID-2175




Refer to the warning message text.Not all spans have the same OSPF area ID. This willcause problemswith protection switching. To determinethe OSPF area for a given span, click on the span andthe OSPF area will be displayed in the pane to the leftof the network map.

WID-2176

Refer to the warning message text.Only one edit pane can be opened at a time. Theexisting pane will be displayed.

WID-2178

Refer to the warning message text.No update is available because the circuit has beendeleted.

WID-2179

CTC initialization has failed in thespecified step.

The CTC initialization failed during step {0}.EID-2180

You must not include this link as itoriginates from destination of acircuit. It is against the path selectionalgorithm.

This link cannot be included because it originates fromthe destination.

EID-2181

The value of the specified item isinvalid.

The value of {0} is invalid.EID-2182

Refer to the error message text.The circuit roll failed. Bridge and roll is not supportedon VCAT circuits.

EID-2183

Refer to the error message text.Spanning Tree Protocol cannot be enabled on someports because the ports have been assigned anincompatible list of VLANs. You can view theVLAN/Spanning Tree table or reassign the Ethernetport VLANs.

EID-2184

Refer to the error message text.The VLANs on some ports cannot be assigned becausethey are incompatible with the Spanning Tree Protocol.You can view the VLAN/Spanning Tree table orreassign the VLANs.

EID-2185

The software could not bedownloaded onto the specified node.

The software download failed on node {0}.EID-2186

You must shorten the length of thering name.

The ring name cannot exceed {0} characters. Pleasetry again.

EID-2187

The ring ID should not containalphanumeric characters, and must bein the specified range.

The nodes in this ring do not support alphanumericIDs. Please use a ring ID between {0} and {1}.

EID-2188




Refer to the error message text.The TL1 keyword "all" cannot be used as the ringname. Please provide another name.

EID-2189

You have reached the maximumnumber of nodes allowed.

Adding this span will cause the ring to contain morenodes than allowed.

EID-2190

You must supply a ring name.The ring name must not be empty.EID-2191

CTC could not complete the circuitcreation request either because thereare no physical links, or the bandwidthof the available links are alreadyreserved.

A valid route cannot be found for the circuit creationrequest.

EID-2192

Refer to the error message text.A valid route cannot be found for the circuit dropcreation request.

EID-2193

Refer to the error message text.A valid route cannot be found for the roll creationrequest.

EID-2194

Refer to the error message text.The circuit VLAN list cannot be mapped to onespanning tree. You can view the VLAN/Spanning Treetable or reassign VLANs.

EID-2195

There is an error relaunching CTC.CTC cannot be relaunched. {0}EID-2196

There was a CORBA failure, and thetask cannot proceed. Verify the Javaversion.

A CORBA failure occurred. CTC cannot proceed.EID-2197

CTC is unable to switch to thespecified view.

CTC is unable to switch to the {0} view.EID-2198

The login failed on the specified tasks.Login failed on {0} {1}EID-2199

Refer to the error message text.CTC has detected a jar file deletion. The jar file wasused to manage one or more nodes. This CTC sessionwill not be able to manage those nodes and they willappear gray on the network map. It is recommendedthat you exit this CTC session and start a new one.

EID-2200

Intranode circuit must have twosources to be a dual ring interconnect(DRI).

An intra-node DRI circuit must have two sources.EID-2202

You must select a member.No member was selected.EID-2203




The number of circuits cannot be zeroor negative.

The number of circuits must be a positive integer.EID-2204

You must select a circuit type.The circuit type must be selected.EID-2205

Refer to the error message text.The profile cannot be autoselected. Please selectprofile(s) to store and try again.

EID-2206

Reduce the length of the ring name,or remove the alphanumeric charactersfrom the end points.

You cannot add this span. Either the ring name is toolong (that is, ring name length is greater than {0}) orthe endpoints do not support alphanumeric IDs.

EID-2207

The version of Java RuntimeEnvironment (JRE) is either invalidor unsupported.

This is an invalid or unsupported JRE.EID-2208

The user name must be at least of thespecified character length.

The user name must be at least {0} characters long.EID-2209

You must select a package name.No package name was selected.EID-2210

You must select a node for theupgrade.

No node was selected for upgrade.EID-2211

The protected line cannot beprovisioned. Choose another line.

A protected line is not provisionable.EID-2212

The circuit state, specified by {0}cannot be applied to the selecteddrops.

The current type or state of some drops does not allowthe new circuit state of {0} to be applied to themindirectly.

WID-2213

Refer to the error message text.The node is disconnected. Please wait until the nodereconnects.

EID-2214

There was an error while leaving thespecified page.

An error occurred while leaving the {0} page.EID-2215

There was an error while entering thespecified page.

An error occurred while entering the {0} page.EID-2216

Refer to the error message text.Some conditions could not be retrieved from thenetwork view

EID-2217

The bandwidth must be within thespecified parameters.

The bandwidth must be between {0} and {1} percent.EID-2218




As the protection operation failed, across-connect (XC) loopback will beapplied on cross-connection.

The protection operation failed. An XC loopback wasapplied on the cross-connection.

EID-2219

Refer to the error message text.The tunnel status is PARTIAL. CTC is not able tochange it. Please try again later.

EID-2220

Refer to the error message text.A valid route cannot be found for the unprotected to{0} upgrade request.

EID-2221

The nodes, specified by {1}, arealready part of a 4-fiberBLSR/MS-SPRing type (specified by{0}).

One or more of the following nodes are currently partof a four-fiber {0}. Only a single four-fiber {0} issupported per node. {1}

EID-2222

Refer to the error message text.Only one circuit can be upgraded at a time.EID-2223

Refer to the error message text.This link may not be included because it terminates onthe source.

EID-2224

Roll can be completed only when avalid signal is detected. If not, the rollcompletion may result in an error.

A valid signal could not be detected while trying tocomplete the roll. {0}

EID-2225

Refer to the error message text.The circuit roll failed. {0}EID-2226

You can not delete a circuit that is amember of VCAT circuit.

This VCAT circuit does not support deletion of itsmember circuits.

EID-2320

Refer to the error message text.An error occurred while deleting member circuits. {0}EID-2321

Refer to the warning message text.Not all cross-connects from selected circuits could bemerged into the current circuit. They might appear aspartial circuits.

WID-2322

A monitor circuit does not supportBridge and Roll.

The circuit roll failed. Bridge and roll is not supportedon monitor circuits.

EID-2323

Refer to the error message text.An error occurred during the circuit upgrade. {0}EID-2324

The maximum amount of attempts tounlock this session has been reached.

You have failed {0} times to unlock this session. CTCwill exit after you click OK or close this dialog box.

EID-2325

Refer to the warning message text.Currently, CTC does not support bridge and roll oncircuits that are entirely created by TL1. To continuewith bridge and roll in CTC, the selected circuits mustbe upgraded. Is it OK to upgrade the selected circuitsand continue the bridge and roll operation?

WID-2326




Refer to the warning message text.Currently, CTC does not support bridge and roll oncircuits that are partially created by TL1. To continuewith bridge and roll in CTC, the selected circuits mustbe upgraded. Is it OK to upgrade the selected circuitsand continue the bridge and roll operation?

WID-2327

The attempt to reconfigure thespecified circuit has failed.

An error occurred during the circuit reconfiguration.{0}

EID-2328

A few circuits could not be created.{0} of {1} circuits could not be successfully created.EID-2329

The selected item, specified by {0},is invalid as per the details, specifiedin {1}.

An error occurred during circuit verification. Theselected {0} is invalid! {1}

EID-2330

Deleting the item can affect theservice of CTC.

Deleting {0} might be service affecting.EID-2331

Refer to the error message text.A validation error occurred in row {0}. {1} hold-offtimer for {2} must be between {3}-10,000 ms, in stepsof 100 ms.

EID-2332

Refer to the error message text.The SSLIOP port cannot have the same port value asIIOP port. Please change it and apply again.

EID-2333

Change a few parameters in anEthernet remote monitoring (RMON)threshold and try again.

An Ethernet RMON thresholdwith the same parametersalready exists. Please change one or more of theparameters and try again.

EID-3001

There was an error while retrievingthe defaults from the specified node.

An error occurred while retrieving defaults from thenode: {0}

EID-3002

CTC cannot load the specified file.The file {0} cannot be loaded.EID-3003

Refer to the error message text.Properties cannot be loaded from the node.EID-3004

CTC cannot save the network element(NE) update values to the specifiedfile.

NE update properties cannot be saved to the file {0}.EID-3005

Refer to the error message text.NE update properties cannot be loaded from the node.EID-3006

There was a provisioning error for thespecified item.

An error occurred while provisioning the {0}.EID-3007




You cannot perform DWDMautomatic node setup (ANS) from theCard view. Please navigate to theNode view and try again.

This is not a valid card.EID-3008

Select the specified item, for example,VLAN, port, slot, etc.

No {0} was selected.EID-3009

Refer to the error message text.A bidirectional optical link could not be created.EID-3010

Refer to the error message text.The subnet address is invalid.EID-3016

Refer to the error message text.The subnet address already exists.EID-3017

Enter the complete internal subnetaddress.

The internal subnet address is incomplete.EID-3019

A node internal subnet must bedifferent from one another as eachTSC is on separate ethernet buses,isolated by broadcast domains.

The subnet address cannot be the same for both TSCcards. The requested action is not allowed.

EID-3020

Refer to the error message text.An error occurred while retrieving the diagnostics: {0}EID-3021

The requested action is not allowed.The requested action is not allowed.EID-3022

Refer to the error message text.The low order cross-connect mode could not beretrieved.

EID-3023

CTC cannot switch the cross-connectmode for the specified item, as thetype or the number of circuits does notmatch with the criterion for switchingmodes.

The {0} cross-connect mode could not be switched.Please verify that the type and/or number of circuitsprovisioned does not exceed the criterion for switchingmodes.

EID-3024

There was an error retrieving thethresholds.

An error occurred while retrieving thresholds.EID-3025

You cannot modify the SendDoNotUse field.

The send DoNotUse attribute cannot be modified.EID-3026

You cannot modify the SyncMsgfield.

The SyncMsg attribute cannot be modified.EID-3027

You cannot change the port type.The port type cannot be changed.EID-3028

Refer to the error message text.Unable to switch to the byte because an overheadchange is present on this byte of the port.

EID-3029




There was an error while resettingcard hardware.

An error occurred while hard-resetting the card.EID-3031

There was an error while resetting thecard.

An error occurred while resetting the card.EID-3032

Refer to the error message text.The lamp test is not supported on this shelf.EID-3033

Refer to the error message text.The cross-connect diagnostics cannot be performedEID-3035

The cross-connect diagnostics test isnot supported on this shelf.

The cross-connect diagnostics test is not supported onthis shelf.

EID-3036

There was an error while changing thecard.

An error occurred while changing the card type.EID-3039

The selected card type is invalid.The card type is invalid.EID-3040

CTC is unable to create a protectiongroup. Check if the protect portsupports circuits, a timing reference,SONET SDCC, orderwire, or a testaccess point.

An error occurred while applying changes.EID-3041

Refer to the error message text.The flow control low value must be less than the flowcontrol high value for all ports in the card.

EID-3042

The flow control watermark valuemust be between the two specifiedvalues.

The flow control watermark value must be between{0} and {1}, inclusive.

EID-3046

Refer to the error message text.The file {0} could not be read. Please verify the nameand try again.

EID-3047

CTC could not find the configurationfile for IOS startup.

There is no Cisco IOS startup configuration fileavailable to download.

EID-3048

Refer to the error message text.The download cannot be done at this time because anupdate in progress.

EID-3049

Check whether the file already existsand cannot be over written, or there isa space constraint in the file system.

An error occurred while trying to save the file to yourlocal file system.

EID-3050

The size of the configuration fileshould not exceed the specifiednumber of bytes.

The configuration file has amaximum size of {0} bytes.EID-3051




Refer to the error message text.An error occurred while saving the configuration fileto the TCC2/TCC2P.

EID-3052

The value of the itemmust be betweenthe specified values.

The value of {0} must be between {1} and {2}.EID-3053

Another user may be updating thecard. You can try again later.

The provisioned input/output ports cannot be removedor another user is updating the card. Please try toremove these ports later.

EID-3054

Refer to the error message text.The soak maintenance pane cannot be created.EID-3055

CTC cannot save the defaults to thespecified file.

Defaults cannot be saved to the file {0}.EID-3056

Refer to the error message text.Default properties cannot be loaded from the node.EID-3057

Refer to the error message text.The file {0} does not exist.EID-3058

There was an error while refreshing.An error occurred while refreshing.EID-3059

The automatic laser shutdown (ALS)Recovery Interval must be betweenthe specified range of seconds.

The ALS recovery pulse interval must be between {0}seconds and {1} seconds.

EID-3060

The automatic laser shutdown (ALS)Recovery Duration must be betweenthe specified range of seconds.

The ALS recovery pulse durationmust be between {0}seconds and {1} seconds.

EID-3061

Refer to the error message text.An error occurred while setting values in the table.EID-3062

This card is not a G1000-4 card.This is not a G1000 card.EID-3064

You must wait some time before youtry again.

An error occurred while attempting to create thisRMON threshold: {0}

EID-3065

Refer to the error message text.The sample period must be between 10 and {0}.EID-3066

This is an invalid rising thresholdentry. The valid range is from 1 to thespecified value.

The rising threshold must be between 1 and {0}.EID-3067

This is an invalid falling thresholdentry. The valid range is from 1 to thespecified value.

The falling threshold must be between 1 and {0}.EID-3068

Refer to the error message text.The rising threshold must be greater than or equal tothe falling threshold.

EID-3069




CTC encountered data error for thespecified ports. Only one VLANshould be marked untagged for eachport.

Error in data for ports {0} Exactly one VLANmust bemarked untagged for each port. These changes will notbe applied.

EID-3070

Unable to retrieve the learned MACaddress from the NE.

An error occurred while retrieving the learned addresslist.

EID-3071

Failure attempting to clear the learnedMAC address from a specific card orEther group.

An error occurred while clearing the learned address.EID-3072

Failure attempting to clear the learnedMAC address from a specific card orEther group.

An error occurred while clearing the selected rows.EID-3073

Error encountered trying to clear thelearned MAC address from either aVLAN or a port.

An error occurred while clearing the learned addresslist by {0}.

EID-3074

Refer to the error message text.At least one row in the parameter column must beselected.

EID-3075

Refer to the error message text.CTC lost its connection with this node. The NE SetupWizard will exit.

EID-3076

Refer to the error message text.No optical link was selected.EID-3077

Refer to the error message text.An optical link could not be created.EID-3078

CTC cannot apply the defaults to thespecified node.

Defaults cannot be applied to the node. {0}EID-3079

CTC cannot go to the specified targettab.

CTC cannot navigate to the target tab. {0}EID-3080

Refer to the error message text.The port type cannot be changed.EID-3081

You cannot modify the specifiedextension byte.

The {0} extension byte cannot be changed.EID-3082

There is no card, or there was aninternal communications error whenattempting to get the laser parametersfor the card.

An error occurred while retrieving laser parameters for{0}.

EID-3084

Select an OSC termination andproceed.

No OSC Terminations were selectedEID-3085




Refer to the error message text.One or more Osc terminations could not be created.EID-3086

Refer to the error message text.The OSC termination could not be edited.EID-3087

No card of the specified type isavailable to switch.

No {0} card is present to switch.EID-3088

You cannot use or change thespecified state when the card is failedor missing.

The {0} state cannot be used or changed when the {1}has failed or is missing.

EID-3089

You cannot perform operation.The operation cannot be performed because the {0} is{1}LOCKED_ON/LOCKED_OUT.

EID-3090

Refer to the error message text.The operation cannot be performed because the protectcard is active.

EID-3091

Select another service state andproceed.

The requested action cannot be applied because theservice state is invalid.

EID-3092

Refer to the error message text.The operation cannot be performed because the duplexpair is {0}locked.

EID-3093

You cannot perform the requestedoperation on the cross connect cardwithout having a backup cross connectcard.

The operation cannot be performed because nocross-connect redundancy is available.

EID-3094

Refer to the error message text.The deletion failed because the circuit is in useEID-3095

Refer to the warning message text.An internal communication error was encounteredwhile retrieving laser parameters. This can happenwhen equipment is not present or when equipment isresetting. Check the equipment state and try to refreshthe values again.

WID-3096

The ring termination you are trying toaccess is in use. Try after sometime.

The ring termination is in use.EID-3097

Select one of the ring terminations.No ring terminations were selected.EID-3098

Check the authentication key andreenter.

The entered key does not match the existingauthentication key.

EID-3099

There was an error in authentication.Verify that the key does not exceedthe character limit.

An error occurred during authentication.EID-3100




The DCC metric should be in therange of 1 to 65535.

The DCC metric must be between 1 and 65535.EID-3101

There was an invalid DCC metric.The DCC metric is invalid.EID-3102

The IP address is invalid.The IP address {0} is invalid}.EID-3103

The router priority should be in therange of 0 to 255.

The router priority must be between 0 and 255.EID-3104

The router priority is invalid.The router priority is invalid.EID-3105

The hello interval should be in therange of 1 to 65535.

The hello interval must be between 1 and 65535.EID-3106

The hello interval is invalid.The hello interval is invalid.EID-3107

The dead interval value must bebetween 1 and 2147483647.

The dead interval must be between 1 and 2147483647.EID-3109

Refer to the error message text.The dead interval must be larger than the hello interval.EID-3110

The LAN transit delay should be inthe range of 1 to 3600 seconds.

The LAN transmit delay must be between 1 and 3600seconds.

EID-3111

The transmit delay is invalid.The transmit delay is invalid.EID-3112

The retransmit interval should be inthe range of 1 to 3600 seconds.

The retransmit interval must be between 1 and 3600seconds.

EID-3113

The retransmit interval is invalid.The retransmit interval is invalid.EID-3114

The LAN metric should be in therange of 1 to 65535.

The LAN metric must be between 1 and 65535.EID-3115

The LAN metric is invalid.The LAN metric is invalid.EID-3116

Refer to the error message text.If OSPF is active on the LAN, no DCC area IDs maybe 0.0.0.0. Please change all DCC area IDs tonon-0.0.0.0 values before enabling OSPF on the LAN.

EID-3117

LANmust be part of a different OSPFarea other than the DCC network.

If OSPF is active on the LAN, the LAN area ID cannotbe the same as the DCC area ID.

EID-3118




CTCwas unable to validate the valuesentered by the user. This errormessage is common to severaldifferent provisioning tabs withinCTC (examples include the SNMPprovisioning tab, the General>Network provisioning tab, theSecurity > Configuration provisioningtab, etc.).

An error occurred during validation.EID-3119

Choose an object of the specified typeto delete.

No object of type {0} was selected for deletion.EID-3120

There is an error deleting the item.An error occurred while deleting {0}.EID-3121

Choose an object of the specified typeto edit.

No object of type {0} was selected to edit.EID-3122

There was an error editing the item.An error occurred while editing {0}.EID-3123

Refer to the error message text.The {0} termination is in use. Delete the associatedOSPF range table entry and try again.

EID-3124

No specified terminations are selected.No {0} terminations were selected.EID-3125

CTC could not edit the specifiedtermination.

The {0} termination could not be edited.EID-3126

Refer to the error message text.Orderwire cannot be provisioned because the E2 byteis in use by {0}.

EID-3127

The authentication key cannot exceedthe specified number of characters.

The authentication key cannot exceed {0} characters.EID-3128

Refer to the error message text.The authentication keys do not match!EID-3129

CTC encountered an error whilecreating the area virtual link.

An error occurred while creating the OSPF area virtuallink.

EID-3130

CTC encountered an error creating thevirtual link.

An error occurred while creating the OSPF virtual link.EID-3131

CTC encountered an error whilesetting the area range for the specifiedvalues.

An error occurred while setting the OSPF area range:{0}, {1}, false.

EID-3132

OSPF area ranges exceeded themaximum number.

The maximum number of OSPF area ranges has beenexceeded.

EID-3133




Refer to the error message text.The area ID is invalid. Use the DCC OSPF area ID,LAN port area ID, or 0.0.0.0.

EID-3134

Refer to the error message text.The mask is invalid.EID-3135

The range address is invalid. Tryagain.

The range address is invalid.EID-3136

Refer to the error message text.Your request has been denied because the timing sourceinformation was updated while your changes were stillpending. Please retry.

EID-3137

You have selected an invalid clocksource. Choose another clock.

The clock source for switching is invalid.EID-3138

Refer to the error message text.A switch cannot be made to a reference of inferiorquality.

EID-3139

You cannot switch the timing sourcemanually when a higher priorityswitch is already active.

A higher priority switch is already active.EID-3140

Refer to the error message text.An attempt was made to access a bad reference.EID-3141

None of the switches are active.No switch is active.EID-3142

CTC encountered an error while acreating static route entry.

An error occurred while creating the static route entry.EID-3143

The number of static routes hasexceeded its limit.

The maximum number of static routes has beenexceeded.

EID-3144

The Routing Information Protocol(RIP) metric should be in the range of1 to 15.

The RIP metric must be between 1 and 15.EID-3145

Refer to the error message text.The RIP metric is invalid.EID-3146

There was an error while creating thesummary address.

An error occurred while creating the summary address.EID-3147

You must provision any one of thelayer 2 domain.

No Layer 2 domain has been provisioned.EID-3148

Refer to the error message text.The MAC addresses could not be retrieved.EID-3149

The specified target file is not anormal file.

The target file {0} is not a normal file.EID-3150




The target file is not writeable.Specify another file.

The target file {0} is not writable.EID-3151

CTC encountered an error creatingProtection Group.

An error occurred while creating the protection group.EID-3152

Refer to the error message text.The card cannot be deleted because it is in use.EID-3153

CTC cannot perform the task on thecard.

An error occurred while provisioning the card: CTCcannot {0} the card.

EID-3154

CTC encountered an error buildingthe menu.

An error occurred while building the menu.EID-3155

CTC encountered an error whilebuilding the menu, as cards could notbe found for the specified group).

An error occurred while building the menu. Cards werenot found for the {0} group.

EID-3156

CTC encountered an unexpectedmodel class while trying to completethe task.

The selected model could not be set because of anunexpected model class: {0}.

EID-3157

Refer to the error message text.Probable causes: - Unable to switch, because a similaror higher priority condition exists on a peer or far-endcard. - A loopback is present on the working port. -Protect port is in OOS disabled admin state

EID-3158

CTC encountered an error whileapplying this operation.

EID-3159 can appear if you attemptto perform another switchingoperation within a certain timeinterval. This interval is an algorithmof three seconds per working card inthe protection group. The maximuminterval is 10 seconds.

An error occurred while applying the operation.EID-3159

CTC encountered the specified error.An error occurred while provisioning the {0}.EID-3160

An error was encountered whileattempting to upgrade the BLSR.Refer to the details portion of the errordialog box for more information.

An error occurred while upgrading the ring.EID-3161

Refer to the error message text.This protection operation cannot be set because theprotection operation on the other side has been changedbut not yet applied.

EID-3162




CTC cannot validate the data for thespecified row.

The data in row {0} cannot be validated.EID-3163

The new specified node ID for thespecified ring ID is the same asanother node ID.

The new node ID ({0}) for ring ID {1} duplicates theID of node {2}.

EID-3164

Refer to the error message text.The ring ID provided is already in use. Ring IDs mustbe unique.

EID-3165

CTC encountered an error whilerefreshing the specified table.

An error occurred while refreshing the {0} table.EID-3166

Refer to the error message text.The slot is already in use.EID-3167

An error was encountered whileattempting the specified provisioningoperation. Refer to the details portionof the error dialog box for moreinformation.

An error occurred while provisioning.EID-3168

CTC encountered an error whileadding the card.

An error occurred while adding the card.EID-3169

Refer to the error message text.You cannot delete this card: {0}.EID-3170

CTC encountered an error creating thetrap destination.

An error occurred while creating the trap destination.EID-3171

Select an RMON threshold.No RMON thresholds were selected.EID-3172

The specified contact exceeds thespecified character limit.

The contact ''{0}'' cannot exceed {1} characters.EID-3173

The specified location exceeds thespecified character limit.

The description ''{0}'' cannot exceed {1} characters.EID-3174

The specified operator identifierexceeds the specified character limit.

The operator identifier ''{0}'' cannot exceed {1}characters.

EID-3175

The specified operator specificinformation exceeds the specifiedcharacter limit.

The operator specific information ''{0}'' cannot exceed{1} characters.

EID-3176

The specified name is empty.The node name cannot be empty.EID-3177

The specified name exceeds thespecified character limit.

The node name ''{0}'' cannot exceed {1} characters.EID-3178




Refer to the error message text.The protect card is in use.EID-3179

Create a 1+1 protection group.The 1+1 protection group does not exist.EID-3180

Refer to the error message text.The Y-cable protection group does not exist.EID-3181

You cannot delete the topologyelement which is in use.

The topology element is in use and cannot be deletedas requested.

EID-3182

CTC encountered an error whiledeleting the protection group.

An error occurred while deleting the protection group.EID-3183

You must select an item beforecompleting this task.

No {0} was selected.EID-3184

Refer to the error message text.This ring has an active protection switch operation andcannot be deleted at this time.

EID-3185

The request cannot be completed.The node is busy: {0} is {1} and cannot be deleted asrequested.

EID-3186

CTC encountered an error deleting thetrap destination.

An error occurred while deleting the trap destination.EID-3187

The password you entered is invalid.Enter the password again.

An error occurred during authentication. The passwordentered is invalid.

EID-3188

Refer to the error message text.The sum of the {0} must be between {1} and {2}.EID-3189

The number of High Orders(STS/STM) for the line is notavailable.

The number of high order circuits for the line couldnot be retrieved.

EID-3214

Used frequently in pane classes toindicate a general error conditionwhen trying to refresh from themodel.

An error occurred while refreshing.EID-3215

Refer to the error message text.The proxy port is invalid.EID-3216

CTC could not refresh statisticsvalues.

The statistics could not be refreshed.EID-3217

Refer to the error message text.The automatic node setup could not be launched.EID-3218

Failure trying to retrieve automaticnode setup information.

The automatic node setup information could not berefreshed.

EID-3219

Error refreshing the specified row.An error occurred while refreshing row {0}.EID-3220




Refer to the error message text.The statistics could not be cleared.EID-3222

Used frequently in pane classes toindicate a general error conditionwhen trying to refresh from themodel.

An error occurred while refreshing the pane.EID-3225

Refer to the error message text.The {0} termination(s) could not be deleted. {1}EID-3226

CTC failed to set the baseline valueswhile provisioning NE. Previousvalues remain unchanged.

A baseline could not be recorded. Performance metricswill remain unchanged.

EID-3227

Refer to the error message text.The {0} termination(s) could not be created. {1}EID-3228

Turn off the Routing InformationProtocol (RIP) on the LAN, beforeenabling OSPF.

RIP is active on the LAN. Please disable RIP beforeenabling OSPF.

EID-3229

Turn off the OSPF on the LAN beforeenabling RIP.

OSPF is active on the LAN. Please disable OSPF beforeenabling RIP.

EID-3230

An error was encountered whileattempting to provision the opticalpower received (OPR).

An error occurred while setting the OPR.EID-3231

Edit the port state while provisioningthe port.

The port state cannot be indirectly transitioned becausethe port is still providing services. If the port stateshould be changed, edit it directly through portprovisioning.

WID-3232

Refer to the error message text.The current loopback provisioning does not allow thisstate transition.

EID-3233

You cannot transition the port state tothe target date while in the currentsynchronization state.

The current synchronization provisioning does notallow this state transition.

EID-3234

Refer to the error message text.The requested state transition cannot be performed onthis software version.

EID-3235

CTC failed to restore the specifieddatabase.

The database restore failed. {0}EID-3236

CTC failed to backup the specifieddatabase.

The database backup failed. {0}EID-3237




The send payload defect indicator path(PDI-P) setting on the specified itemshould be consistent with that of thespecified control node.

The send PDIP setting on {0} is inconsistent with thesetting on the control node {1}.

EID-3238

Refer to the error message text.The overhead termination is invalidEID-3239

Overhead terminations have exceededthe limit.

The maximum number of overhead terminations hasbeen exceeded.

EID-3240

The specified termination port is inuse. Select another port.

The {0} termination port is in use.EID-3241

The specified DCC already exists onthe selected port. You can create aDCC of another type.

An {1} exists on the selected ports. Therefore, youmust create the {0}s one by one.

EID-3242

The same port can not be used bymultiple DCCs.

The port you have chosen as an {0} endpoint alreadysupports an {1}. The port cannot support both DCCs.After the {0} is created, verify that no EOC alarms arepresent and then delete the {1} to complete thedowngrade.

WID-3243

The specified DCC already exists onthe selected port. You can create aDCC of another type.

An {0} exists on the selected ports. Therefore, youmust create the {1}s one by one.

EID-3244

The port selected as a DCC endpointalready supports another DCC. Referto the warning message text.

The port you have chosen as an {1} endpoint alreadysupports an {0}. The port cannot support both DCCs.After the {1} is created, verify that no EOC alarms arepresent and then delete the {0} to complete the upgrade.

WID-3245

CTC encountered an error.The wizard was not able to validate the data. {0}EID-3246

The absolute value entered waswrong.

An ordering error occurred. The absolute value shouldbe {0}.

EID-3247

CTC changed the incorrect parameter.The value for the parameter {0} is invalid.EID-3248

Refer to the error message text.The voltage increment value is invalid.EID-3249

Refer to the error message text.The power monitor range is invalid.EID-3250

CTC could not complete the specifiedaction.

The requested action could not be completed. {0}EID-3251

Refer to the error message text.No download has been initiated from this CTC session.EID-3252




Refer to the error message text.The reboot operation failed. {0}EID-3253

The Cisco Transport Controller (CTC)was unable to validate the valuesentered by the user, specified by {0}.This error message is common toseveral different provisioning tabswithin the CTC.

An error occurred during validation. {0}EID-3254

Refer to the error message text.You cannot change the timing configuration becausea Manual/Force operation is in effect.

EID-3255

Refer to the warning message text.The timing reference(s) could not be assigned becauseone or more of the timing reference(s): - is already usedand/or - has been selected twice and/or - is attemptingto use the same slot twice. Please verify the settings.

WID-3256

CTC detected more than oneoccurrence of the a DCC number.Remove one of them.

Duplicate DCC numbers are not permitted. {0}.EID-3257

Refer to the error message text.A software error occurredwhile attempting to downloadthe file. Please try again later.

EID-3258

You must create a Fibre ChannelMultirate (FC_MR) card threshold.

An error occurred while creating the FC-MR threshold.EID-3259

The specified internal subnet couldnot be provisoned.

An error occurred while provisioning the internalsubnet: {0}

EID-3260

Refer to the error message text.The port rate provisioning cannot be changed whilecircuits exist on this port.

EID-3261

You must provision the ports onlywhen the port is Out of Service.

The port provisioning cannot be changed when the portstatus is {0}.

EID-3262

CTC is being launchedwith the wrongversion of the JRE {0}. This versionof CTC requires a particular versionof the JRE {1}. The CTC and browsermust be closed and restarted to allowthe correct Java version to be loaded.

You are using Java version {0}. CTC should run withJava version {1}. It can be obtained from theinstallation CD or http://java.sun.com/j2se/

WID-3263

Protection Group could not bemodified.

An error occurred while modifying the protectiongroup.

EID-3265

Refer to the error message text.Conditions could not be retrieved from the shelf or cardview.

EID-3266




Refer to the warning message text.The XTC protection group cannot be modified.WID-3267

The specified entry is invalid.The filter entry is invalid. {0}WID-3268

Refer to the error message text.The {0} operation was successfully initiated for {1}but its completion status could not be obtained fromthe node. When the node is accessible, check itssoftware version to verify if the {0} succeeded.

WID-3269

The specified file does not exist.The file {0} does not exist.WID-3270

The value enteredmust be greater thanthe specified value.

The value entered must be greater than {0}.WID-3271

An entry is required to complete thistask.

An entry is required.WID-3272

The specified item already exists inthe list.

{0} already exists in the list.WID-3273

Refer to the warning message text.A software upgrade is in progress. Networkconfiguration changes that result in a node rebootcannot take place during a software upgrade. Pleasetry again after the software upgrade is done.

WID-3274

Refer to the warning message text.Ensure that the remote interface ID and the localinterface ID on the two sidesmatch. (The local interfaceID on this node should equal the remote interface IDon the neighbor node and vice-versa).

WID-3275

The specified port has both SDCC andLDCC.

Both {0} and {1} exist on the same selected port. {2}WID-3276

The input exceeds the character limit.The value will be truncated to themaximum character limit.

The description cannot exceed {0} characters. Yourinput will be truncated.

WID-3277

CTC returns to node view.This card has been deleted. CTCwill return to the shelfview.

WID-3279

Refer to the warning message text.ALSwill not engage until both the protected trunk portsdetect LOS.

WID-3280

Refer to the warning message text.Performing a software upgrade while TSC 5 is activecould result in a service disruption. It is recommendedthat you make TSC 10 the active TSC by performinga soft reset of TSC 5. The following ONS 15600s arecurrently unsafe to upgrade...

WID-3282




Refer to the warning message text.Before activating a new version, ensure that you havea database backup from the current version.

WID-3283

CTC is being reverted to an olderversion of application.

Reverting to an older version.WID-3284

Refer to the warning message text.Applying FORCE or LOCKOUT operations mightresult in traffic loss.

WID-3285

Refer to the warning message text.The ring status is INCOMPLETE. CTC cannotdetermine if there are existing protection operations orswitches in other parts of the ring. Applying aprotection operation at this time could cause a trafficoutage. Please confirm that no other protectionoperations or switches exist before continuing.

WID-3286

Refer to the warning message text.There is a protection operation or protection switchpresent on the ring. Applying this protection operationnow will probably cause a traffic outage.

WID-3287

Change the ring status to apply thechange to all nodes in the ring type.

The status of this ring is INCOMPLETE. CTCwill notbe able to apply this change to all of the nodes in the{0}.

WID-3288

Refer to the error message text.The specified provisionable patchcord(s) could not bedeleted.

EID-3290

Protection switch should not be activeto change the revertive behavior.

The revertive behavior cannot be changed because aprotection switch is active.

EID-3291

CTC encountered an error whileresetting the node.

An error occurred while resetting the shelf.EID-3292

You are attempting to delete aprovisionable patchcord that does notexist. This happens when multipleinstances of CTC are running andattempting to delete the sameprovisionable patchcord concurrently.

No such provisionable patchcords exists.EID-3293

Refer to the error message text.No RMON thresholds are available for the selectedport.

EID-3294

Refer to the error message text.This card does not support RMON thresholds.EID-3295

Refer to the error message text.Buffer-to-buffer credit is only supported for FibreChannel (FC) and FICON.

EID-3296




Refer to the error message text.This interfaces does not support ALS auto restart.EID-3298

OSPF area IDs should be unique.Duplicate OSPF area IDs are not permitted.EID-3300

Refer to the error message text.The LAN metric cannot be zero.EID-3301

Standby controller card is not ready.The standby {0} is not ready.EID-3302

DCCArea ID and ring type, specifiedby {0}, conflict each other due to thedetails specified by {1}.

The DCC area ID and {0} conflict. {1}EID-3303

Enter a DCC number that is within therange

The DCC number is out of range.EID-3304

You cannot have the default OSPFarea on a DCCwhile OSPF is enabledon the LAN.

OSPF cannot be active on the LAN interface when thebackbone area is set on a DCC interface.

EID-3305

Refer to the error message text.Ethernet circuits must be bidirectional.EID-3306

CTC encountered an error at thespecified connection while creatingthe connection.

An error occurred while creating a connection objectat {0}.

EID-3307

Refer to the error message text.DWDM links can be used only for optical channelcircuits.

EID-3308

The optical channel (circuit) does notallow the specified link to be includedbecause it is in the wrong opticaldirection.

The link was excluded because it was in the wrongdirection.

EID-3309

Refer to the error message text.The DWDM link does not have wavelengths available.EID-3310

Refer to the error message text.The laser is already on.EID-3311

CTC cannot change the powersetpoint. The new setpoint wouldeithermake the thresholds inconsistentor set the fail threshold outside therange.

The power setpoint cannot be changed. {0} {1}EID-3312

Refer to the error message text.The offset cannot be modified because the service stateof the port is IS.

EID-3313

Refer to the error message text.The requested action is not allowed. The state value isinvalid.

EID-3314




CTC is unable to perform operation.This operation cannot be performed.EID-3315

This task was applied to the wrongnode side.

The node side is invalid.EID-3316

Reduce the number of characters inthe name.

The ring name is too long.EID-3317

The name you entered is illegal.The ring name is invalid.EID-3318

Select another lineThe wrong line was selected.EID-3319

CTC cannot delete the optical link.The optical link could not be deleted.EID-3320

Refer to the error message text.This feature is unsupported by this version of software.EID-3321

Plug-in the equipment and proceed.The equipment is not plugged in.EID-3322

Automatic Power Control (APC)system is busy.

The APC system is busy.EID-3323

There is no circuit path to regulate.There is no path to regulate.EID-3324

Generic DWDM provisioning failuremessage.

The requested action is not allowed.EID-3325

The input value is incorrect.The input was invalid.EID-3326

There was an error retrieving thethresholds. This message is displayedonly for the OSCM/OSC-CSM linethresholds.

An error occurred while retrieving thresholds.EID-3327

There was an error applying thechanges to the specified row. Thevalue is out of range.

An error occurred while applying changes to row {0}.The value is out of range.

EID-3328

Refer to the error message text.Unable to switch to the byte because an overheadchannel is present on this byte of the port.

EID-3330

Refer to the error message text.An error occurred while applying changes to the row.EID-3331

You cannot change timing parameterson protect port.

Timing parameters on the protect port cannot bechanged.

EID-3334




Refer to the error message text.The port type cannot be changed because the SDHvalidation check failed. Check if this port is part of acircuit, protection group, SONET DCC, orderwire, orUNI-C interface.

EID-3335

The Control Mode must be retrieved.An error occurred while reading a control mode value.EID-3336

The Gain Set Point must be set.An error occurred while setting a set point gain value.EID-3337

The Gain Set Point must be retrieved.An error occurred while reading a set-point gain value.EID-3338

The tilt calibration must be set.An error occurred while setting a tilt calibration value.EID-3339

The expected wavelength must be set.An error occurred while setting expected wavelength.EID-3340

The expected wavelength must beretrieved.

An error occurred while reading expected wavelength.EID-3341

The actual wavelength must beretrieved.

An error occurred while reading actual wavelength.EID-3342

The actual band must be retrieved.An error occurred while reading actual band.EID-3343

The expected band must be retrieved.An error occurred while reading expected band.EID-3344

The expected band must be set.An error occurred while setting expected band.EID-3345

There was an error retrieving defaultsfrom the specified node.

An error occurred while retrieving defaults from thenode: {0}.

EID-3346

CTC cannot load the specified file.The file {0} cannot be loaded.EID-3347

Refer to the error message text.Properties cannot be loaded from the node.EID-3348

Check your file system for spaceconstraint or any other problem.

NE update properties cannot be saved to a file.EID-3349

Refer to the error message text.NE update properties cannot be loaded from the node.EID-3350

The specified file does not exist.The file {0} does not exist.EID-3351

There was an error while setting thevalue at the specified location.

An error occurred while setting a value at {0}.EID-3352

The interface specified is not presentin CTC.

No such interface is available.EID-3353




Select another endpoint that is not inuse.

The specified endpoint is in use.EID-3354

Refer to the error message text.The specified endpoint is incompatible.EID-3355

Refer to the error message text.The connections could not be calculated.EID-3357

Create an optical linkmodel for theinterface, and proceed.

An optical link model does not exist for the specifiedinterface.

EID-3358

Refer to the error message text.Optical parameters could not be set for the node.EID-3359

Refer to the error message text.ANS cannot be performed. Please check {0} parametervalue.

EID-3360

You cannot delete a ring in use.The ring termination is in use. An error occurred whiledeleting the ring termination.

EID-3361

There was an error while deleting ringtermination.

An error occurred while deleting the ring termination.EID-3362

You must select a ring termination.No ring terminations were selected.EID-3363

There was an error while creating thering ID.

An error occurred while creating the ring ID.EID-3364

Select another optical service channel(OSC) which is not in use.

The OSC termination is in use.EID-3365

There was an error deleting the OSCtermination.

The OSC termination could not be deleted.EID-3366

You must select an optical link.No optical link was selected.EID-3370

Refer to the error message text.An error occurred while calculating the automaticoptical link list.

EID-3371

CTC destroyed an external attempt toaccess an optical channel networkconnection.

CTC attempted to access an OCHNC connection thathas been destroyed.

EID-3372

Refer to the error message text.The expected span loss must be set.EID-3375

Refer to the error message text.The measured span loss could not be retrieved.EID-3376

The interface used for the card iswrong.

The wrong interface was used.EID-3377



Descript

error messages - cisco · error messages - cisco ... eid-6017

Documents