error code manual - Форумыforum.delta-systems.ru/docs/mx8600(vtb24)_error code...

Error Code Manual MONiMAX8600 System

V01.00.03 (2016. 12. 14)

© 2016 Nautilus Hyosung Inc. All Rights Reserved.


Revision History

Error Code Manual – MX8600 System

No. Version Date Description of Change Chapter

1 V01.00.00 2014/09/25 New Publication All

2 V01.00.01 2016/08/30 Updated all chapters All

3 V01.00.02 2016/10/25 Added “95D0014, 95D1326, 95D1318, 9530317, 2

9590800, 9590900, 9591000”

4 V01.00.03 2016/12/14 Added error codes in chapter2. 2

(9513300 and so on)

© 2016 Nautilus Hyosung All Rights Reserved.

The content of this specification is protected by copyright laws.

2016. 10. 25. 3rd Release


Contents

Chapter1. Barcode Reader .................................................................................................................................. 1-1

Chapter2. Bill Recycling Machine (BRM) ............................................................................................................. 2-1

Chapter3. Camera ................................................................................................................................................ 3-1

Chapter4. Card Reader ........................................................................................................................................ 4-1

Chapter5. Encryption PIN Pad (EPP) .................................................................................................................. 5-1

Chapter6. Journal Printer ..................................................................................................................................... 6-1

Chapter7. Receipt Printer (SPR) .......................................................................................................................... 7-1

Chapter8. RF Module ........................................................................................................................................... 8-1

Chapter9. UPNC .................................................................................................................................................. 9-1

Notes ............................................................................................................................................................ Notes-1

Error Code Manual Chapter1. Barcode Reader

© 2016 Nautilus Hyosung Inc. All Rights Reserved. 1-1

Chapter1. Barcode Reader

Problem Code Problem Description Trouble Shooting

9708014 Failed to open communication port Check the serial port, cable, or reset the unit to recover. It it is not recovered, replace main board or the unit.

9708030 Failed to create Registry 1 .SP Close and Open(Take the Log for failure) 2. Restart the system

9708031 Failed to read Registry 1 .SP Close and Open(Take the Log for failure) 2. Restart the system

9708032 Failed to write Registry 1 .SP Close and Open(Take the Log for failure) 2. Restart the system

9708034 Failed to delete Registry 1 .SP Close and Open(Take the Log for failure) 2. Restart the system

9708042 Failed to run sensor polling thread. 1 .SP Close and Open(Take the Log for failure) 2. Restart the system

9708043 Failed to stop sensor polling thread. 1 .SP Close and Open(Take the Log for failure) 2. Restart the system

9708101 Failed to make enable barcode Device 1 .SP Close and Open(Take the Log for failure) 2. Restart the system

9708102 Failed to make disable barcode Device 1 .SP Close and Open(Take the Log for failure) 2. Restart the system

9708103 Failed to read data from barcode device 1 .SP Close and Open(Take the Log for failure) 2. Restart the system

9708104 communication error between SP and firmware during idle status.

1 .SP Close and Open(Take the Log for failure) 2. Restart the system

9708105 encountered unexpected timeout from firmware.

1 .SP Close and Open(Take the Log for failure) 2. Restart the system

Error Code Manual Chapter2. Bill Recycling Machine (BRM)


Chapter2. Bill Recycling Machine (BRM)


5@AE600 Error to received Download command. during TE Button Operating by applying encryption.

1. Operate to initialize BRM(Recovery) 2. Reboot the system when same error occurred (message timeout error) after initialization

5@AEE00 RBU RS485 communication sequence disorder during Download by applying encryption.


5@AEF00 RBU RS485 connection line disorder during Download by applying encryption.


5@AH500 Error to NVRAM(128denominations) Read/ Write during Download by applying encryption.


5@AHA00 Checksum disorder when MAIN EP Download by applying encryption.

1. Check the download bin file 2. Change the bin file

5@AHB00 Flash Rom write failure when MAIN EP Download by applying encryption.

1. Change MAIN board when same error occurred after retry download

5@BHA00 Effectiveness disorder when RBU EP Download by applying encryption.

1. Check the download bin file 2. Change the bin file

5@BHB00 Flash Rom write failure when RBU EP Download by applying encryption.

1. Change RBU board when same error occurred after retry download

5@US100 Duplicated USB sequence number error during applying encryption.

"1. Restart over AP-SP"

5@US300 USB command data length error during applying encryption.


5@USA00 Error to compare INFORMATION 1 from 0xC1 command during applying encryption.


5@USB00 Error to compare INFORMATION 2 from 0xC1 command during applying encryption.


5@USC00 Error to compare EPRN from 0xEE command during applying encryption.


5@USD00 Security session status is not AUTH_SUCCESS from 0xEE command during applying encryption.


5@USE00 Error to perform security Libray API during applying encryption.(0xC1 Error to open EP)


5@USF00 Error to perform security Libray API during applying encryption.(0xC2 Error to done EP)


5@USG00 Error to perform security Libray API during applying encryption.(0xEE Error to received full text deciphering)


Chapter2. Bill Recycling Machine (BRM) Error Code Manual

2-2 © 2016 Nautilus Hyosung Inc. All Rights Reserved.


5@USH00 Error to read INFORMATION during applying encryption.


5@USJ00 Error to write INFORMATION during applying encryption.


5@USK00 When received C1 command in previous encryption during applying encryption, exist INFORMATION.


5@USL00 When received plain text during applying encryption, INFORMATION exist.


5@USM00 When to resend encryption bulk during applying encryption, no INFORMATION.


5@USP00 Received undefined command during applying encryption.


5@USQ00 Failed to encryption during applying encryption.


5@USR00 Failed to encryption mode at EP DONE during applying encryption.


5@USS00 Undefined command at C1, C2 command during applying encryption .


5@UST00 Failed to encryption at bulk retransmission during applying encryption.


5@USU00 When received C1 during applying encryption, INFORMATION 1 is NULL


5@USV00 When received C1 during applying encryption, INFORMATION 2 is NULL


5102100 Error occurred by the notes remained on the GS801 during Deposit Ready.

"1. Open the upper unit. 2. Open the customer service module (CSM)3. Open the BC(5) 4.Remove notes and substance in the Front Transport Path(4) 5. Check whether the sensor is contaminated or not if there are No notes or substance "

5102200 Error occurred by the notes remained on GS002 during Deposit Ready.

"1. Open the upper unit2. Open the customer service module (CSM)3. Open the BC(5)4. Remove the notes and the substance from the Front Transport Path (4)5. Check whether the sensor is contaminated or not if there are No notes or substance"

5102300 Error occurred by the notes remained on GS003 during Deposit Ready .

"1. Open the upper unit. 2. Open the TE(Temporary Escrow) (12). 3. Open the Rear Transport Path(6) 4. Remove notes and substance in the Rear Transport Path(6)5. Check whether the sensor is contaminated or not if there are No notes or substance "





"1. Open the upper unit. 2. Open the TE(Temporary Escrow) (12)3. Open the cassette not received(9). 4. Remove notes and substance in the Rear Transport Path(6)5. Check whether the sensor is contaminated or not if there are No notes or substance "


"1. Open the upper unit. 2. Open the TE(Temporary Escrow) (12)3. Remove notes and substance in the Rear Transport Path(11)4. Check whether the sensor is contaminated or not if there are No notes or substance "


"1. Open the upper unit. 2. Open the TE(Temporary Escrow) (12)3. Open the cassette no received(9). 4. Remove notes and substance in the Rear Transport Path(7)5. Check whether the sensor is contaminated or not if there are No notes or substance"

5102A00 Error occurred by the notes remained on GS021 during Deposit Ready .

"1. Open the lower unit2. Remove notes and substance in the Mid Transport Path(13)3. Check whether the sensor is contaminated or not if there are No notes or substance"

5102B00 Error occurred by the notes remained on GS022 during Deposit Ready .

"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the banknotes and the foreign substance from the reject cassette (19).4. Check whether the sensor is contaminated or not if there are No notes or substance"

5102G00 Error occurred by the notes remained on GS614 during Deposit Ready .

"1. Open the upper unit. 2. Open the customer service module (CSM)(3)3. Remove notes and substance in the CSM(3)4. Check whether the sensor is contaminated or not if there are No notes or substance"

5102H00 Error occurred by the notes remained on GS618 during Deposit Ready .

"1. Open the upper unit. 2. Open the customer service module (CSM)(3)3. Remove notes and substance in the Rear Transport Path(11)4. Check whether the sensor is contaminated or not if there are No notes or substance"

5102J00 Error occurred by the notes remained on GS619 during Deposit Ready .





5102K00 Error occurred by the notes remained on GS703 during Deposit Ready .

"1. Open the upper unit2. Open the TE(Temporary Escrow) (12)3. Rotate a knob of TE(12)4. Remove notes and substance in the Rear Transport Path(11)"

5102M00 Error occurred by the notes remained on GS031 during Deposit Ready .

"1. Open the lower unit. 2. Rotate the knob of the Mid Transport Path. 3. Remove notes and substance in the Mid Transport Path (13).4. Check whether the sensor is contaminated or not if there are No notes or substance"

5102N00 Error occurred by the notes remained on GS032 during Deposit Ready .


5102P00 Error occurred by the notes remained on GS033 during Deposit Ready .


5102Q00 Error occurred by the notes remained on GS034 during Deposit Ready .


510G100 Failure to 3 Way Gate 0 degree mode conversion during Deposit Ready .

"1. Open the upper unit. 2. Open the CSM and TE(12)3. Remove notes and substance from the gate in the Rear Transport Path"

510G200 Failure to 3 Way Gate 120 degree mode conversion during Deposit Ready .

"1. Open the upper unit. 2. Open the CSM and TE(12)3. Remove notes and substance from the gate in the Rear Transport Path"

510NC00 Failure to check the last note at the termination of mid transport path during Deposit Ready.

"1. Operate to initialize BRM(Recovery)2. Reboot the system when same error occurred (message timeout error) after initialization"

510NK00 No gate for insertion error during Deposit Ready.


510R100 Message timeout error during operation ready in the Deposit Ready.





510R200 Message timeout error during operation ready in the Deposit Ready .


510R300 Message timeout error during postprocessing to Deposit End Error.


510RJ00 Message timeout error during Stop Ready in the Deposit Ready.


5111100 GS101 sensor jam during Deposit Ready.

"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (A) . 4. Put down the Stage after open the recycle cassette door (A)5.Remove notes and substance using jam removal Knob in the upper side6. Check whether the sensor is contaminated or not if there are No notes or substance"

5111200 GS102 sensor jam during Deposit Ready .











5112500 Failure of return notes to GS101 during Deposit Ready.


511G100 Failure of return notes to GS101 during Deposit Ready.


511G200 Failure to move the position of RC1 PP stack during Deposit Ready.

"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (A) . 4. Open the recycle cassette door (A)5. Check cassette status to move stage up and down6. Check the lower edge of the door's right side(Key part) if you don't find any problem"

511G400 Failure to upword moving of PP during RC1 stack roller retreat movement in the Deposit Ready.

"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (A) . 4. Open the recycle cassette door (A)5. Check cassette status to move stage up and down6. Check the lower edge of the door's right side(Key part) if you don't find any problem"

511G500 Failure of RC1 stack roller retreat during Deposit Ready.(sensor error)

"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (A) . 4. Put down the Stage after open the recycle cassette door (A)5.Check the jam removal knob rotates softly"

511G600 Exceeds retry count limit of detecting RC1 stack roller's falling back and avoiding during Deposit Ready.





511G800 Failure to RC1 push pressure movement during Deposit Ready.

"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (A) . 4. Put down the Stage after open the recycle cassette door (A)5.Check upper side of the recycle cassette "

511GA00 RC1 solenoid echo error duing Deposit Ready.

"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (A) . 4. Reload the recycle cassette (A) after removing recycle cassette5. Change the cassette when same error occur"

511GB00 Encoder Sensor(GS107) for Feed Motor failed to detect Light status when Feed Motor runs in stacking direction duing Deposit Ready.

"1. Open the lower unit.2. Open the Mid Transport Path.3. Take out the recycle cassette #1 and open its door.(A)4. Remove jammed notes or substance using any wheels on the upper side.5. See whether GS107 works fine if there is nothing jammed."

511GC00 Encoder Sensor(GS107) for Feed Motor failed to detect Dark status when Feed Motor runs in stacking direction duing Deposit Ready.

"1. Open the lower unit.2. Open the Mid Transport Path.3. Take out the recycle cassette #1 and open its door.(A)4. Remove jammed notes or substance using any wheels on the upper side.5. See whether GS107 works fine if there is nothing jammed."

511GJ00 Failure of RC1 stack roller retreat during Deposit Ready.(Overrun)


511GK00 Failure of RC1 stack roller retreat during Deposit Ready.(Motor status error)


511GL00 Failure to move RC1 feed roller to home position during Deposit Ready. (Motor status error)

"1. Open the lower unit2. Open the Mid Transport Path3. Remove the recycle cassette (A)4. Put down the Stage after open the recycle cassette door (A)5. Remove notes and substance using jam removal Knob in the upper side6. Check the GS107 sensor status if there are No notes or substance"

511J300 RC1 full check failure during Deposit Ready.

"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (A) . 4. Check the stage status after open the recycle cassette(A)6.Check contamination of GS112 sensor"




511S100 Undefined return values of RC1 during Deposit Ready.


511S200 Undefined command of RC1 during Deposit Ready .



"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (B) . 4. Put down the Stage after open the recycle cassette door (B)5.Remove notes and substance using jam removal Knob in the upper side6. Check whether the sensor is contaminated or not if there are No notes or substance"





5122100 Error occurred by the banknote remaining on GS201 during Deposit Ready .









512G100 Failure of return notes to RC2 during Deposit Ready.


512G200 Failure to move stack position of RC2 PP during Deposit Ready.

"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (B) . 4. Open the recycle cassette door (B)5. Check cassette status to move stage up and down6. Check to demage lower edge of the door's right side(Key part) if you don't find any problem"

512G400 Failure to upword moving of PP during RC2 stack roller retreat movement in the Deposit Ready .

"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (B) . 4. Open the recycle cassette door (B)5. Check cassette status to move stage up and down6. Check to demage lower edge of the door's right side(Key part) if you don't find any problem"


"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (B) . 4. Put down the Stage after open the recycle cassette door (B)5.Check the jam removal knob rotates softly"




"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (B) . 4. Put down the Stage after open the recycle cassette door (B)5.Check the upper side of the recycle cassette "




512GA00 RC2 solenoid echo error during Deposit Ready.

"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (B) . 4. Reload the recycle cassette (B) after removing recycle cassette5. Change the cassette when same error occur"

512GB00 Encoder Sensor(GS207) for Feed Motor failed to detect Light status when Feed Motor runs in stacking direction during Deposit Ready.

"1. Open the lower unit.2. Open the Mid Transport Path.3. Take out the recycle cassette #2 and open its door.(B)4. Remove jammed notes or substance using any wheels on the upper side.5. See whether GS207 works fine if there is nothing jammed."

512GC00 Encoder Sensor(GS207) for Feed Motor failed to detect Dark status when Feed Motor runs in stacking direction during Deposit Ready.

"1. Open the lower unit.2. Open the Mid Transport Path.3. Take out the recycle cassette #2 and open its door.(B)4. Remove jammed notes or substance using any wheels on the upper side.5. See whether GS207 works fine if there is nothing jammed."





512GL00 Failure to move RC2 feed roller to home position during Deposit Ready. (Motor status error)

"1. Open the lower unit2. Open the Mid Transport Path3. Remove the recycle cassette (B)4. Put down the Stage after open the recycle cassette door (B)5. Remove notes and substance using jam removal Knob in the upper side6. Check the GS207 sensor status if there are No notes or substance"

512J300 Failure to RC2 full check during Deposit Ready.

"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (B) . 4. Check the stage status after open the recycle cassette(B)6.Check contamination status of the GS112 sensor"

512S100 RC2 message timeout error during operation ready in the Deposit Ready.





512S200 RC2 message timeout error during transation operation in the Deposit Ready .



"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (C) . 4. Put down the Stage after open the recycle cassette door (C)5.Remove notes and substance using jam removal Knob in the upper side6. Check whether the sensor is contaminated or not if there are No notes or substance"





5132100 Error occurred by the notes remained on the GS301 during Deposit Ready .











513G200 RC3 PP stack position movement failure during Deposit Ready.

"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (C) . 4. Open the recycle cassette door (C)5. Check cassette status to move stage up and down6. Check to demage lower edge of the door's right side(Key part) if you don't find any problem"


"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (C) . 4. Open the recycle cassette door (C)5. Check cassette status to move stage up and down6. Check to demage lower edge of the door's right side(Key part) if you don't find any problem"

513G500 Failure of RC3 stack roller retreat during Deposit Ready .(sensor error)

"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (C) . 4. Put down the Stage after open the recycle cassette door (C)5.Check the jam removal knob rotates softly"



513G800 Failure to RC3 push pressure movement of during Deposit Ready.

"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (C) . 4. Put down the Stage after open the recycle cassette door (C)5.Check the upper side of the recycle cassette "





"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (C) . 4. Reload the recycle cassette (C) after removing recycle cassette5. Change the cassette when same error occur"


"1. Open the lower unit.2. Open the Mid Transport Path.3. Take out the recycle cassette #3 and open its door.(C)4. Remove jammed notes or substance using any wheels on the upper side.5. See whether GS307 works fine if there is nothing jammed."


"1. Open the lower unit.2. Open the Mid Transport Path.3. Take out the recycle cassette #3 and open its door.(C)4. Remove jammed notes or substance using any wheels on the upper side.5. See whether GS307 works fine if there is nothing jammed."

513GJ00 Failure of RC3 stack roller retreat during Deposit Ready .(Overrun)




513GL00 Failure to move RC3 feed roller to home position during Deposit Ready.(Motor status error)

"1. Open the lower unit2. Open the Mid Transport Path3. Remove the recycle cassette (C)4. Put down the Stage after open the recycle cassette door (C)5. Remove notes and substance using jam removal Knob in the upper side6. Check the GS307 sensor status if there are No notes or substance"

513J300 Failure to RC3 full check RC3 during Deposit Ready.

"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (C) . 4. Check the stage status after open the recycle cassette(C)6.Check contamination status of the GS312 sensor"









"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (D) . 4. Put down the Stage after open the recycle cassette door (D)5.Remove notes and substance using jam removal Knob in the upper side6. Check whether the sensor is contaminated or not if there are No notes or substance"














514G100 Failure of return notes to RC4 during Deposit Ready.


514G200 Failure to move stack position of RC4 PP during Deposit Ready.

"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (D) . 4. Open the recycle cassette door (D)5. Check cassette status to move stage up and down6. Check to demage lower edge of the door's right side(Key part) if you don't find any problem"


"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (D) . 4. Open the recycle cassette door (D)5. Check cassette status to move stage up and down6. Check to demage lower edge of the door's right side(Key part) if you don't find any problem"

514G500 Failure to RC4 stack roller retreat during Deposit Ready.(sensor error)

"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (D) . 4. Put down the Stage after open the recycle cassette door (D)5.Check the jam removal knob rotates softly"




"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (D) . 4. Put down the Stage after open the recycle cassette door (D)5.Check the upper side of the recycle cassette "





"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (D) . 4. Reload the recycle cassette (D) after removing recycle cassette5. Change the cassette when same error occur"


"1. Open the lower unit.2. Open the Mid Transport Path.3. Take out the recycle cassette #4 and open its door.(D)4. Remove jammed notes or substance using any wheels on the upper side.5. See whether GS407 works fine if there is nothing jammed."


"1. Open the lower unit.2. Open the Mid Transport Path.3. Take out the recycle cassette #4 and open its door.(D)4. Remove jammed notes or substance using any wheels on the upper side.5. See whether GS407 works fine if there is nothing jammed."

514GJ00 Failure to RC4 stack roller retreat during Deposit Ready.(Overrun)


514GK00 Failure to RC4 stack roller retreat during Deposit Ready.(Motor status error)



"1. Open the lower unit2. Open the Mid Transport Path3. Remove the recycle cassette (D)4. Put down the Stage after open the recycle cassette door (D)5. Remove notes and substance using jam removal Knob in the upper side6. Check the GS407 sensor status if there are No notes or substance"

514J300 Failure to RC4 full check during Deposit Ready.

"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (D) . 4. Check the stage status after open the recycle cassette(D)6.Check contamination status of the GS412 sensor"

514S100 Undefined return value of RC4 during Deposit Ready.





514S200 Undefined command of RC4 during Deposit Ready.



"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (E) . 4. Put down the Stage after open the recycle cassette door (E)5.Remove notes and substance using jam removal Knob in the upper side6. Check whether the sensor is contaminated or not if there are No notes or substance"







5152200 Error occurred by the notes remained on GS502 during Deposit Ready.









515G200 RC5 PP stack position movement failure during Deposit Ready.

"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (E) . 4. Open the recycle cassette door (E)5. Check cassette status to move stage up and down6. Check to demage lower edge of the door's right side(Key part) if you don't find any problem"

515G400 Failure to upword moving of PP during RC5 stack roller retreat movement in the Deposit Ready.

"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (E) . 4. Open the recycle cassette door (E)5. Check cassette status to move stage up and down6. Check to demage lower edge of the door's right side(Key part) if you don't find any problem"


"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (E) . 4. Put down the Stage after open the recycle cassette door (E)5.Check the jam removal knob rotates softly"




"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (E) . 4. Put down the Stage after open the recycle cassette door (E)5.Check the upper side of the recycle cassette "





"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (E) . 4. Reload the recycle cassette (E) after removing recycle cassette5. Change the cassette when same error occur"

515GB00 Encoder Sensor(GS507) for Feed Motor failed to detect Light status when Feed Motor runs in stacking direction. during Deposit Ready.

"1. Open the lower unit.2. Open the Mid Transport Path.3. Take out the recycle cassette #5 and open its door.(E)4. Remove jammed notes or substance using any wheels on the upper side.5. See whether GS507 works fine if there is nothing jammed."


"1. Open the lower unit.2. Open the Mid Transport Path.3. Take out the recycle cassette #5 and open its door.(E)4. Remove jammed notes or substance using any wheels on the upper side.5. See whether GS507 works fine if there is nothing jammed."






"1. Open the lower unit2. Open the Mid Transport Path3. Remove the recycle cassette (E)4. Put down the Stage after open the recycle cassette door (E)5. Remove notes and substance using jam removal Knob in the upper side6. Check the GS507 sensor status if there are No notes or substance"

515J300 RC5 full check failure during Deposit Ready.

"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the recycle cassette (E) . 4. Check the stage status after open the recycle cassette(E)6.Check contamination status of the GS512 sensor"








5162100 Error occurred by the notes remained in CSM during Deposit Ready .

"1. Open the upper unit. 2. Open the customer service module (CSM)3.Remove notes and substance in the CSM(1) 4. Check whether the sensor is contaminated or not if there are No notes or substance "

5162400 Undefined error of CSM during Deposit Ready .


516G100 Error of BP stack position movement during Deposit Ready.

"1. Open the upper unit. 2. Open the customer service module (CSM) shutter(1)3.Check the notes and substance inside of the CSM"

516G200 BP notes out error during Deposit Ready.


516G300 BP separate position movement error during Deposit Ready.

"1. Open the upper unit. 2. Open the customer service module (CSM) shutter(1)3.Check the notes and substance inside of the CSM "

516G400 BP separate control error during Deposit Ready.


516G500 BP notes out error during Deposit Ready.


516G600 Failure to move pick-up roller to home position during Deposit Ready.

"1. Open the upper unit. 2. Check the knob rotates softly in the CSM(2) "

516G800 Failure to revert notes during Deposit Ready(Separate moter disorder).

"1. Open the upper unit2. Check the notes and substance in the CSM(2)3. Check the knob rotates softly in the CSM(2) 4. Check the GS660 sensor status"

516GA00 Failure to move withdrawal(stack) position of stack roller during Deposit ReadyStack roller (GM605 disorder).

"1. Open the upper unit. 2. Check the knob rotates softly in the CSM(3)"

516GB00 Failure to move deposit(stack) position of stack roller during Deposit ReadyStack roller (GM605 disorder).


516GC00 Failure to control stack roller during Deposit Ready Stack roller (GM605 disorder).


516GD00 Failure to Lift-up during Deposit Ready..





516GE00 Failure to Lift-down during Deposit Ready..


516GF00 Failure to move gate roller to home position during Deposit Ready.

"1. Open the upper unit. 2. Check the knob rotates softly in the CSM(2) "

516P100 PP withdrawal(stack) position movement error during Deposit Ready .

"1. Open the upper unit. 2. Check PP rotates softly using knob of the CSM(1) "

516P200 PP deposit position movement error during Deposit Ready.


516P300 PP separate position movement error during Deposit Ready.


516P400 PP lose return position movement error during Deposit Ready.


516P500 PP notes out error during Deposit Ready .


516P600 PP notes alignment error during Deposit Ready .


516P700 PP separate control(during separating) error during Deposit Ready .


516P800 PP stack control(during stacking) error during Deposit Ready .


516P900 Error of reverting notes during Deposit Ready .

"1. Open the upper unit. 2. Check the notes and substance in the CSM(2)3. Check the knob rotates softly in the CSM(2)4. Check the contamination of the sensor in the CSM(2) "

516PA00 PP ready stop error during Deposit Ready .


516R100 CSM message timeout error during operation ready in the Deposit Ready .


516R200 CSM message timeout error during transaction operation in the Deposit Ready .


516R300 CSM message timeout error during postprocessing of Deposit Ready Error.





516RJ00 CSM message timeout error during Stop Ready in the Edposit Ready.


5171300 GS703 dark jam during Deposit Ready. "1. Open the upper unit2. Open the TE(Temporary Escrow) (12)3. Rotate a knob of TE(12)4. Remove notes and substance in the Rear Transport Path(11)"









517G100 Motor's stack direction running disorder during Deposit Ready.

"1. Open the upper unit2. Confirm to Rotate a knob of TE(12) softly"

517G200 Motor's separate Direction running disorder during Deosit Receipt.


517G300 Moter stop disorder during Deposit Ready.


517G400 No detect the front end in the tape during Deposit Ready.

"1.Open upper Unit2. Check the notes remain in the TE(12)3. Check the color of tape's front end is black in the TE(12)4. Remove notes remain in the TE"

517G500 Detect the front end in the tape during Deposit Ready.

"1.Open upper Unit2. Check the notes remain in the TE(12)3. Check the color of tape's front end is black in the TE(12)4. Remove notes remain in the TE"

517G700 Detect the rear end in the tape during Deposit Ready.

"1.Open upper Unit2. Check the notes remain in the TE(12)3. Cheeck whether black tape is wrap with a drum in the TE(12)4. Remove notes remain in the TE"

517J100 TE drum full during Deposit Ready. "1. Open the upper unit2. Check the notes remain in the TE(12)3. Remove notes remain in the TE"




517R100 TE message timeout error during operation ready in theDeposit Ready.


517R200 TE message timeout error during transaction operation in the Deposit Ready.


517R300 TE message timeout error during postprocessing of Deposit Ready Error.


517RJ00 TE message timeout error during Deposit Ready.


518HA01 Error GS801A during Deposit Ready. "1. Check GS801A2. Operate to initialize BRM(Recovery)"

518HA02 Error GS801B during Deposit Ready. "1. Check GS801B2. Operate to initialize BRM(Recovery)"

518HA03 Error GS801A, GS801B during Deposit Ready.

"1. Check GS801A, GS801B2. Operate to initialize BRM(Recovery)"

518HA04 Error GS802A during Deposit Ready. "1. Check GS802A2. Operate to initialize BRM(Recovery)"

518HA05 Error GS801A, GS802A during Deposit Ready.

"1. Check GS801A, GS802A2. Operate to initialize BRM(Recovery)"

518HA06 Error GS801B, GS802A during Deposit Ready.

"1. Check GS801B, GS802A2. Operate to initialize BRM(Recovery)"

518HA07 Error GS801A, GS801B, GS802A during Deposit Ready.

"1. Check GS801A, GS801B, GS802A2. Operate to initialize BRM(Recovery)"

518HA08 Error GS802B during Deposit Ready. "1. Check GS802B2. Operate to initialize BRM(Recovery)"



518HA10 Error GS801B, GS802B during Deposit Ready.

"1. Check GS801B, GS802B2. Operate to initialize BRM(Recovery)"

518HA11 Error GS801A, GS801B, GS802B during Deposit Ready.

"1. Check GS801A, GS801B, GS802B2. Operate to initialize BRM(Recovery)"



518HA13 Error GS801A, GS802A, GS802B during Deposit Ready.

"1. Check GS801A, GS802A, GS802B2. Operate to initialize BRM(Recovery)"

518HA14 Error GS801B, GS802A, GS802B during Deposit Ready.

"1. Check GS801B, GS802A, GS802B2. Operate to initialize BRM(Recovery)"

518HA15 Error GS801A, GS801B, GS802A, GS802B during Deposit Ready.

"1. Check GS801A, GS801B, GS802A, GS802B2. Operate to initialize BRM(Recovery)"

518HF03 Error to load shading data of the CIS during Deposit Ready.

"1. Operate shading in the BC CIS2. Operate to initialize BRM(Recovery)"

518HF04 Error to load recognition DB table during Deposit Ready.

"1.Download DB again after delecting all recognition DB2. Operate to initialize BRM(Recovery)"




518HF05 Error to BC FPGA data checksum during deposit ready..

"1. Check to BC FPGA File2. Operate to initialize BRM(Recovery)"

518HF06 Error to BC FPGA configuration during deposit ready..

"1. Re-download BC FPGA2. Change the BC B/D if continuous error."

518HF07 Error to load to info of BC FPGA header during deposit ready..


518HF08 Error to FPGA initialize during deposit ready..


518HF09 Error to FPGA Read during deposit ready..


518HF11 Error to load recognition DB #01 during Deposit Ready.




















518HG01 Error of mode set up during BCU Mode Command in the Deposit Ready.

"1. Operate to initialize BRM(Recovery)2. Reboot the system when same error occurred after initialization"

518HG02 Error of the recognition level set up during BCU mode command in the Deposit Ready.


518HG03 Error of the transaction ready set up during BCU ready command in the Deposit Ready.


518HG04 Error of mode set up during BCU ready command in the Deposit Ready.





518HG05 Error of the recognition level set up during BCU ready command in the Deposit Ready.


518HG06 Error of the BC insert direction during BCU ready command in the Deposit Ready.


518HG07 Error of BCU undefined command reception during Deposit Ready.


518HG08 Error of available support country numbers set up during receiving BCU data write command in the Deposit Ready .

"1. Check the country2. Operate to initialize BRM(Recovery)3. Reboot the system when same error occurred after initialization"

518HG09 Error of country-code set up during receiving BCU data write command in the Deposit Ready .

"1. Check the country 2. Operate to initialize BRM(Recovery)3. Reboot the system when same error occurred after initialization"

518HG10 Error of no recognition DB for the country during receiving BCU data write command in the Deposit Ready .

"1. Check the country 2. Download DB again after delecting all recognition DB3. Operate to initialize BRM(Recovery)4. Reboot the system when same error occurred after initialization"

518HG11 Error of no country code set up during receiving BCU ready command in the Deposit Ready .

"1. Check the country 2. Operate to initialize BRM(Recovery)3. Reboot the system when same error occurred after initialization"

518HG12 BC spec differs from data write command paramter during deposit ready..

"1. Check the BCU specifications.2. Operate to initialize BRM(Recovery)3. Reboot the system when same error occurred after initializatio"

518HG20 Error to initialize CIS during receiving BCU ready command in the Deposit Ready .

"1. Operate to initialize BRM(Recovery)2. Check whether the sensor is contaminated or not if same error occures after Initialize3. Reboot the system when same error occures even though there is no substance "

518HG21 Error of power on during receiving BCU ready command in the Deposit Ready .


518HG22 Error of DD sensor initialization during receiving BCU ready command in the Deposit Ready .





518HG23 Error of set up for DD sensor DAC during receiving BCU ready command in the Deposit Ready .


518HG24 Error of encoder set-up mode during receiving BCU ready command in the Deposit Ready .


518HG36 Error of recognized mode during receiving BCU mode command in the Deposit Ready .

"1. Check to the recoginzed mode2. Operate to initialize BRM(Recovery)3. Reboot the system when same error occurred (message timeout error) after initialization"

518HG37 Error of transaction setting during receiving BCU mode command in the Deposit Ready .

"1. Check to the transaction setting2. Operate to initialize BRM(Recovery)3. Reboot the system when same error occurred (message timeout error) after initialization"

518HI01 Error of Timeout during RecogTask Message in the Deposit Ready.


518HI02 Error of Timeout during ScanTask Message Message in the Deposit Ready.


518HI03 Error of Timeout during UartTask Message in the Deposit Ready.


518HI04 Error of Timeout during BcUsbTask Message in the Deposit Ready.


518HJ01 Error of Initialize Recognition Algorithm in the Deposit Ready.


518HJ02 Error of Ready Recognition Algorithm in the Deposit Ready.


518HJ03 Error of Currency Set Recognition Algorithm in the Deposit Ready.


518HS01 Error of the Fpga Write Scan Driver Init During in the Deposit Ready.





518HS02 Error of the Sensor(MR/UV/DD/Gate) Power Off Scan Driver Init During in the Deposit Ready.


518HS03 Error of the CIS Led On Value Set Fail Scan Driver Init During in the Deposit Ready.


518HS04 Error of the Light Source Set Fail Scan Driver Init During in the Deposit Ready.


518HS05 Error of the CIS Shading Scan Driver Init During in the Deposit Ready.

1. Retry to Cis Sensor Shading

518HS08 Error of the DAC Set Fail Scan Driver Init During in the Deposit Ready.


518HS11 Error of the Fpga Write BCU Ready During in the Deposit Ready.


518HS12 Error of the Sensor(MR/UV/DD/Gate) Power Off BCU Ready During in the Deposit Ready.


518HS13 Error of the CIS Led On Value Set Fail BCU Ready During in the Deposit Ready.


518HS14 Error of the Light Source Set Fail BCU Ready During in the Deposit Ready.


518HS15 Error of the CIS Shading BCU Ready During in the Deposit Ready.

"1. Retry to Cis Sensor Shading"

518HS17 Error of the AFE Chip Set BCU Ready During in the Deposit Ready.


518HS18 Error of the DAC Set Fail BCU Ready During in the Deposit Ready.


518HS19 Error of the MR/UV/DD Sampling BCU Ready During in the Deposit Ready.


518HS1A Error of the Hall Sensor Dac Set Fail BCU Ready During in the Deposit Ready.

"1. Check to Hall Sensor2. Check to Hall Sensor Connected Cable"

518HS1B Error of the Hall Sensor Shading Fail BCU Ready During in the Deposit Ready.

"1. Retry to Hall Sensor Shading"




518HS22 Error of the BC Stop Sensor(MR/UV/DD/Gate) Power Off Scan Driver Init During in the Deposit Ready.


518HS28 Error of the BC Stop DAC Set Fail Scan Driver Init During in the Deposit Ready.


518HS29 Error of the BC Stop MR/UV/DD Sampling BCU Ready During in the Deposit Ready.


51A2100 Status of remaining notes on the Transport Path (GS801) before the operation during Deopsit Ready.

"1. Open the upper unit. 2. Open the customer service module (CSM)3. Open the BC(5)4. Remove notes and substance in the Front Transport Path(4) 5. Check whether the sensor is contaminated or not if there are No notes or substance "

51A2200 Status of remaining notes on the Transport Path (GS002) before the operation during Deopsit Ready .

"1. Open the upper unit2. Open the customer service module (CSM)3. Open the BC(5)4. Remove the notes and the substance from the Front Transport Path (4)5. Check whether the sensor is contaminated or not if there are No notes or substance"


"1. Open the upper unit. 2. Open the TE(Temporary Escrow) (12). 3. Open the Rear Transport Path(6) 4. Remove notes and substance in the Rear Transport Path(6)5. Check whether the sensor is contaminated or not if there are No notes or substance "




"1. Open the upper unit. 2. Open the TE(Temporary Escrow) (12)3. Remove notes and substance in the Rear Transport Path(11)4. Check whether the sensor is contaminated or not if there are No notes or substance "







1. Open the upper unit. 2. Open the TE(Temporary Escrow) (12) 3. Open the cassette not received(9). 4. Remove notes and substance in the Rear Transport Path(8) 5. Check whether the sensor is contaminated or not if there are No notes or substance

51A2A00 Status of remaining notes on the Transport Path (GS021) before the operation during Deopsit Ready .

"1. Open the lower unit2. Remove notes and substance in the Mid Transport Path(13)3. Check whether the sensor is contaminated or not if there are No notes or substance"

51A2B00 Status of remaining notes on the Transport Path (GS022) before the operation during Deopsit Ready .

"1. Open the lower unit. 2. Open the Mid Transport Path. 3. Remove the banknotes and the foreign substance from the reject cassette (19).4. Check whether the sensor is contaminated or not if there are No notes or substance"

51A2G00 Status of remaining notes on the Transport Path (GS614) before the operation during Deopsit Ready .

"1. Open the upper unit. 2. Open the customer service module (CSM)(3)3. Remove notes and substance in the CSM(3)4. Check whether the sensor is contaminated or not if there are No notes or substance"

51A2H00 Status of remaining notes on the Transport Path (GS618) before the operation during Deopsit Ready .


51A2J00 Status of remaining notes on the Transport Path (GS619) before the operation during Deopsit Ready .


51A2K00 Status of remaining notes on the Transport Path (GS703) before the operation during Deopsit Ready .





51A2M00 Status of remaining notes on the Transport Path (GS031) before the operation during Deopsit Ready .


51A2N00 Status of remaining notes on the Transport Path (GS032) before the operation during Deopsit Ready .


51A2P00 Status of remaining notes on the Transport Path (GS033) before the operation during Deopsit Ready .


51A2Q00 Status of remaining notes on the Transport Path (GS034) before the operation during Deopsit Ready .


51A2W00 Status of remaining notes on the Transport Path (GS802) before the operation during Deopsit Ready .

"1. Open the upper unit. 2. Open the customer service module (CSM)3.Open BC(5) 4. Remove the notes and substance in the BC(5)5. Check whether the sensor is contaminated or not if there are No notes or substance "

51AA100 Status of UTC detachment before the operation during Deposit Ready .

"1. Open the upper Unit2. Check removal status of the cassette not received (9)"

51AA200 S

error code manual - Форумыforum.delta-systems.ru/docs/mx8600(vtb24)_error code...

Documents