ericsson msc commands
DESCRIPTION
Ericsson MSC CommandsTRANSCRIPT
CDLCP
© Telefonaktiebolaget LM Ericsson 2001
Call Duration Supervision, Long Duration Call, Print
1 Format
1.1 Command
CDLCP;
1.2 Parameters
This command has no parameters.
2 Function
The command CDLCP initiates the printout LONG DURATION CALL SUPERVISION DATAthat lists the set-up data of the function time supervision and disconnection of long duration calls and whether automatic disconnection is initiated.
The order does not remain after system restart.
3 Examples
3.1 Example 1
CDLCP;
The command results in an answer printout being issued.
4 Printouts
4.1 Check Printout
No.
4.2 Procedure Printouts
NOT ACCEPTEDfault type
Fault type:
FUNCTION BUSYThe function is busy.
FORMAT ERRORThe command or a parameter was incorrectly specified.
FAULT CODE 10 FUNCTIONALITY NOT SUPPORTED BY THIS EXCHANGE
The functionality addressed by the command is not supported by this exchange.
4.3 Answer Printouts
LONG DURATION CALL SUPERVISION DATA
4.4 Result Printouts
This command has no result printouts.
© Telefonaktiebolaget LM Ericsson 1998
Transmission Function Synchronous Digital Path, State, Print
1 Format
1.1 Command
/ \ |SDIP=sdip... |TPSTP:[IO=io,]+ +; |SDIP=ALL[,STATE=state...]| \ /
1.2 Parameters
IO=io Input/Output (IO) device nameIdentifier 1 - 7 characters
SDIP=sdip Synchronous Digital Path (SDIP) nameIdentifier 1 - 7 characters ALL
All SDIPsSTATE=state State of SDIP
BLOC Blocked
PBLOC Partly blocked
TRAFBLOC Traffic blocked
TRAFLIM Traffic limited
WO Working
2 Function
This command prints the state of specified SDIP on specified or default IO device.
Printout SYNCHRONOUS DIGITAL PATH STATE is received.
Up to 10 SDIPs can be specified in each command.
The order does not remain after system restart.
3 Examples
3.1 Example 1
TPSTP:SDIP=LONDON;
The state of SDIP LONDON is printed.
3.2 Example 2
TPSTP:IO=AT-4,SDIP=LONDON&OSLO;
The state of the SDIPs LONDON and OSLO is printed on IO device AT-4.
3.3 Example 3
TPSTP:SDIP=ALL;
The state of all SDIPs is printed.
3.4 Example 4
TPSTP:IO=AT-4,SDIP=ALL,STATE=WO&BLOC;
All working and all blocked SDIPs are printed on IO device AT-4.
4 Printouts
4.1 Check Printout
No.
4.2 Procedure Printouts
ORDEREDNOT ACCEPTEDfault type
Fault type:
FUNCTION BUSYThe function is busy.
FORMAT ERRORdetails
The command or a parameter was incorrectly specified.
UNREASONABLE VALUEdetails
The parameter was specified with an unreasonable value.
FAULT CODE 2 SDIP DOES NOT EXISTdetails
The specified SDIP does not exist.
FAULT CODE 3 ALL IS NOT ACCEPTED AS AN SDIP NAME
"ALL" is not accepted as a SDIP name.
FAULT CODE 4 NO SDIPS EXIST
No SDIPs exist.
FAULT CODE 5 TOO MANY SDIPS SPECIFIED
Too many SDIPs are specified.
4.3 Answer Printouts
SYNCHRONOUS DIGITAL PATH STATE
4.4 Result Printouts
SYNCHRONOUS DIGITAL PATH STATE
5 Logging
No.
6 Command Category Group
Recommended value 0 (H'0)
Telefonaktiebolaget LM Ericsson 2000
Transcoder Pool Resource Data, Print
1 Format
1.1 Command
/ \ |ALL |/ / \\TKPRP:TRAPOOL=+ +|,DETAILS|,BLOC||; |trapool...|\ \ // \ /
1.2 Parameters
BLOC Blocked transcoder pool resources
Specifies that only the blocked transcoder resources belonging to the transcoder pool are printed.
DETAILS Detail resources
Specifies that all the resources belonging to the transcoder pool are printed.
TRAPOOL=trapool
Transcoder poolIdentifier 1 - 7 characters
2 Function
This command initiates a printout of transcoder pool data for the specified transcoder pools. The data is presented in the answer printout TRANSCODER POOL RESOURCE DATA. If parameter DETAILS is specified in the command, all the transcoder resources connected to the pool are printed with their resource state. If parameter BLOC is specified in the command, only the blocked transcoder resources connected to the pool are printed.
The order does not remain after system restart.
3 Examples
3.1 Example 1
TKPRP:TRAPOOL=UAMR;
The transcoder pool data for the pool UAMR is printed.
3.2 Example 2
TKPRP:TRAPOOL=UAMR,DETAILS;
The transcoder pool data for the pool UAMR is printed. A list of all transcoder resources in the pool is printed.
3.3 Example 3
TKPRP:TRAPOOL=UAMR,DETAILS,BLOC;
The transcoder pool data for the pool UAMR is printed. A list of all the transcoder devices in the pool that are blocked is printed.
4 Printouts
4.1 Check Printout
No.
4.2 Procedure Printouts
NOT ACCEPTEDfault type
Fault type:
FUNCTION BUSYThe function is busy.
FORMAT ERRORThe command or a parameter was incorrectly specified.
UNREASONABLE VALUEdetails
The parameter was specified with an unreasonable value.
FAULT CODE 4 TRANSCODER POOL NAME DOES NOT EXISTdetails
The transcoder pool to be printed does not exist.
FAULT CODE 35 FUNCTIONALITY NOT SUPPORTED BY THIS EXCHANGE
Optional feature transcoder service not supported by this exchange.
4.3 Answer Printouts
TRANSCODER POOL RESOURCE DATA
4.4 Result Printouts
This command has no result printouts.
5 Logging
No.
6 Command Category Group
Recommended value 0 (H'0)
SQTLP
SERVICE QUALITY STATISTICS TIME LIMITS, PRINT
1 Format
1.1 Command
SQTLP;
1.2 Parameters
-
2 Function
The command requests printout of the time limits for post-dialling delay,time to B-answer and conversation time. These times are specified with command SQTLI.The order does not remain after system restart.
3 Examples
3.1 Example
SQTLP;The time limits for post-dialling delay,B-answer and conversation time will be printed.
SQREP
SERVICE QUALITY STATISTICS RESULT, PRINT
1 Format
1.1 Command
/ / \\ | |DETAILED||SQREP:MP=mp|,+ +|; | |SURVEY || \ \ //
1.2 Parameters
DETAILED Detailed answer printoutMP=mp Measuring program identity (Numeral) The number of measuring programs is size alterable. See Application Information for block SEQS3.SURVEY Survey answer printout
2 Function
The command requests a printout of the current servicequality statistics which is received as an answerprintout. If there is no result output period inprogress the previous result output period resultswill be printed.The answer printout can be detailed or survey. Ifthe parameter DETAILED or SURVEY is omitted the answerprintout type will be survey. The detailed answerprintout shows all events. Time limits (PDD, BANSWER,CTIME) which have not been specified are not shown.The survey answer printout is presented in main groups,and events that have not got any registrations willnot be included in this printout.The results are presented in the printout SERVICEQUALITY STATISTICS RESULT and the printout SERVICEQUALITY STATISTICS RESULT SURVEY.The order does not remain after system restart.
3 Examples
3.1 Example 1
SQREP:MP=6;A subresult received as an answer printout isrequested for measuring program 6.The answer printout type is survey.
3.2 Example 2
SQREP:MP=7,DETAILED;A subresult received as an answer printout isrequested for measuring program 7.The answer printout type is detailed.
4 Printouts
4.1 Check Printout
No.
4.2 Procedure Printouts
NOT ACCEPTEDfault type
Fault type:
FORMAT ERROR Format error
UNREASONABLE VALUEdetails Unreasonable value
FAULT CODE 16SPECIFIED MP IS NOT DEFINED FOR THE FUNCTION The specified measuring program is not defined for the function.FAULT CODE 17THE FIRST RECORDING PERIOD HAS NOT STARTED The first recording period has not started.FAULT CODE 24BUFFER FOR OUTPUT NOT AVAILABLE Buffer for output is not available.
Give the command again.
4.3 Answer Printouts
SERVICE QUALITY STATISTICS RESULTSERVICE QUALITY STATISTICS RESULT SURVEY
4.4 Result Printouts
-
5 Logging
No.
6 Command Category Group
Recommended value 0 (H'0).
7 Command Receiving Block
COMMAND DESCRIPTION 3/190 82-CNT 216 1205 Uen A1
SQMPP
SERVICE QUALITY STATISTICS MEASURING PROGRAM, PRINT
1 Format
1.1 Command
/ \ |mp...|SQMPP:MP=+ +; |ALL | \ /
1.2 Parameters
mp Measuring program identity.
ALL All measuring programs defined in the function.
2 Function
The command requests output of data for one or severalmeasuring programs and of the number of idle measuringprograms.The order does not remain after system restart.
3 Examples
3.1 Example 1
SQMPP:MP=1&3;Printout of measuring programs 1 and 3 is requested.
3.2 Example 2
SQMPP:MP=ALL;Printout of all measuring programs is requested.
4 Printouts
4.1 Check Printout
No.
4.2 Procedure Printouts
NOT ACCEPTED fault type
Fault type:
FORMAT ERROR Formal format fault in relation to the command description.
UNREASONABLE VALUE details Unreasonable values, overaddressing.
FAULT CODE 16details The specified measuring program is not defined for the function.
4.3 Answer Printouts
SERVICE QUALITY STATISTICS MEASURING PROGRAM
4.4 Result Printouts
-
5 Logging
No.
6 Command Category Group
Recommended value 0 (H' 0 ).
7 Command Receiving Block
SEQS2
COMMAND DESCRIPTION 2/190 82-CNT 216 1470 Uen B
SQESP
Service Quality Statistics Connection of End-of- Selection Codes, Print
1 Format
1.1 Command
/ \ |event...|SQESP:EVENT=+ +; |ALL | \ /
1.2 Parameters
EVENT=event Event group
ALL All event groups The following events are possible:
GROUP 1:
ARBDAD A-replacement before, during or after dialling
BBUSY B-subscriber busy
BNOEX B-number does not exist
BOUT B-number out of order
CONGGS Congestion in group switch
CONGJT Congestion in junctor terminals
CONGNW Congestion in the network (that is, in the next exchange)
CONGOT Congestion in outgoing trunk (last choice route)
CONGTS Congestion in time switch. (in the digital subscriber switch)
EOSNOSE End-of selection codes not connected to any specified event group
FSIGCR Faulty signal received in code receiver
FSIGCS Faulty signal received in code sender
FSIGIT Faulty signal received in incoming trunk
FSIGOT Faulty signal received in outgoing trunk
HWFCR Hardware fault in code receiver
HWFCS Hardware fault in code sender
HWFJT Hardware fault in junctor terminals
HWFIT Hardware fault in incoming trunk
HWFOT Hardware fault in outgoing trunk
HWFTS Hardware fault in the time switch. (in the digital subscriber switch)
NMBLO Calls blocked due to Network Management actions
TOBDD Time out before or during dialling
TOCS Time out in code sender
TOOT Time out in outgoing trunk
SPARE1 For own use
SPARE2 For own use
SPARE3 For own use
. .
. .
. .
SPARE16 For own use
GROUP 2:
RESHF Hardware fault in speech position
RESSF Signalling fault in speech position
2 Function
Command SQESP requests a printout of specified eventgroups with the corresponding end-of-selectioncodes.The printout SERVICE QUALITY STATISTICSEND-OF-SELECTION CODES PER EVENT is received inanswer to this command.The order does not remain after system restart.
3 Examples
3.1 Example 1
SQESP:EVENT=BBUSY&BOUT&BNOEX;The corresponding end-of-selection codes willbe printed for the following event groups: - B-subscriber busy - B-number out of order - B-number does not exist
3.2 Example 2
SQESP:EVENT=EOSNOSE;The end-of-selection codes which are notconnected to any event group will be printed.
3.3 Example 3
SQESP:EVENT=ALL;End-of-selection codes will be printed for allevent groups.
4 Printouts
4.1 Check Printout
No.
4.2 Procedure Printouts
NOT ACCEPTEDfault type
Fault type:
FORMAT ERROR Format error.
UNREASONABLE VALUEdetails Unreasonable value.
FAULT CODE 26EVENT CANNOT BE SPECIFIED WITH THIS APPLICATION SYSTEM If the application parameter HFANDSFALLOWED is not set, then events RESHF and RESSF are not allowed for the function.
4.3 Answer Printouts
SERVICE QUALITY STATISTICS END-OF-SELECTION CODES PER EVENT
4.4 Result Printouts
-
5 Logging
No.
6 Command Category Group
Recommended value 0 (H'0).
7 Command Receiving Block
SEQS1
COMMAND DESCRIPTION 2/190 82-CNT 216 1470 Uen B
SQESP
Service Quality Statistics Connection of End-of- Selection Codes, Print
1 Format
1.1 Command
/ \ |event...|SQESP:EVENT=+ +; |ALL | \ /
1.2 Parameters
EVENT=event Event group
ALL All event groups The following events are possible:
GROUP 1:
ARBDAD A-replacement before, during or after dialling
BBUSY B-subscriber busy
BNOEX B-number does not exist
BOUT B-number out of order
CONGGS Congestion in group switch
CONGJT Congestion in junctor terminals
CONGNW Congestion in the network (that is, in the next exchange)
CONGOT Congestion in outgoing trunk (last choice route)
CONGTS Congestion in time switch. (in the digital subscriber switch)
EOSNOSE End-of selection codes not connected to any specified event group
FSIGCR Faulty signal received in code receiver
FSIGCS Faulty signal received in code sender
FSIGIT Faulty signal received in incoming trunk
FSIGOT Faulty signal received in outgoing trunk
HWFCR Hardware fault in code receiver
HWFCS Hardware fault in code sender
HWFJT Hardware fault in junctor terminals
HWFIT Hardware fault in incoming trunk
HWFOT Hardware fault in outgoing trunk
HWFTS Hardware fault in the time switch. (in the digital subscriber switch)
NMBLO Calls blocked due to Network Management actions
TOBDD Time out before or during dialling
TOCS Time out in code sender
TOOT Time out in outgoing trunk
SPARE1 For own use
SPARE2 For own use
SPARE3 For own use
. .
. .
. .
SPARE16 For own use
GROUP 2:
RESHF Hardware fault in speech position
RESSF Signalling fault in speech position
2 Function
Command SQESP requests a printout of specified eventgroups with the corresponding end-of-selectioncodes.The printout SERVICE QUALITY STATISTICSEND-OF-SELECTION CODES PER EVENT is received inanswer to this command.The order does not remain after system restart.
3 Examples
3.1 Example 1
SQESP:EVENT=BBUSY&BOUT&BNOEX;The corresponding end-of-selection codes willbe printed for the following event groups: - B-subscriber busy - B-number out of order - B-number does not exist
3.2 Example 2
SQESP:EVENT=EOSNOSE;The end-of-selection codes which are notconnected to any event group will be printed.
3.3 Example 3
SQESP:EVENT=ALL;End-of-selection codes will be printed for allevent groups.
4 Printouts
4.1 Check Printout
No.
4.2 Procedure Printouts
NOT ACCEPTEDfault type
Fault type:
FORMAT ERROR Format error.
UNREASONABLE VALUEdetails Unreasonable value.
FAULT CODE 26EVENT CANNOT BE SPECIFIED WITH THIS APPLICATION SYSTEM If the application parameter HFANDSFALLOWED is not set, then events RESHF and RESSF are not allowed for the function.
4.3 Answer Printouts
SERVICE QUALITY STATISTICS END-OF-SELECTION CODES PER EVENT
4.4 Result Printouts
-
5 Logging
No.
6 Command Category Group
Recommended value 0 (H'0).
7 Command Receiving Block
SEQS1
COMMAND DESCRIPTION 6/190 82-CNT 298 0026 Uen B
NRGGP
© Telefonaktiebolaget LM Ericsson 2001
Network Resourcing, Media Gateway Group, Print
1 Format
1.1 Command
/ \ |mgg...|NRGGP:MGG=+ +; |ALL | \ /
1.2 Parameters
MGG=mgg Media gateway groupText string 1 - 7 characters ALL
All defined Media Gateway Groups (MGG)s.
2 Function
This command orders a printout with information about a specific or all the defined MGGs. When parameter MGG is assigned with a name of a specific MGG, only data for the specified MGG are printed. When it is assigned with the value ALL, data for all defined MGGs are printed.
Answer printout MEDIA GATEWAY GROUP DATA is received.
The order does not remain after system restart.
3 Examples
3.1 Example 1
NRGGP:MGG="MGG4GBR"&"MGG3GR";
Information about media gateway groups "MGG4GBR" and "MGG3GR" are printed.
3.2 Example 2
NRGGP:MGG=ALL;
Information about all defined media gateway groups are printed.
4 Printouts
4.1 Check Printout
No.
4.2 Procedure Printouts
NOT ACCEPTEDfault type
Fault type:
FORMAT ERRORThe command or a parameter was incorrectly specified.
UNREASONABLE VALUEdetails
The parameter was specified with an unreasonable value.
FAULT CODE 10 THE SPECIFIED MGG HAS NOT BEEN DEFINED
The specified MGG has not been defined.
FAULT CODE 14 FUNCTIONALITY NOT SUPPORTED BY THE APPLICATION
The functionality is not supported by the application.
FAULT CODE 26 FUNCTIONALITY NOT SUPPORTED BY THIS EXCHANGE
The functionality is not supported by this exchange.
4.3 Answer Printouts
MEDIA GATEWAY GROUP DATA
4.4 Result Printouts
This command has no result printouts.
5 Logging
No.
6 Command Category Group
Recommended value 00 (H'00)
7 Command Receiving Block
NRM
8 Glossary
MGG Media Gateway Group
9 References
9.1 Printout Descriptions
MEDIA GATEWAY GROUP DATA
COMMAND DESCRIPTION 3/190 82-CNT 238 0164 Uen A
HGSTP
© Telefonaktiebolaget LM Ericsson 1999
Home Location Register, Subscriber Tracing, Print
1 Format
1.1 Command
/ \ |imsi|HGSTP:IMSI=+ +; |ALL | \ /
1.2 Parameters
IMSI=imsi International Mobile Subscriber Identity (IMSI)
See the Application Information for block HTRAN.
ALL All IMSI with initiated trace data
2 Function
This command prints the trace data for mobile subscribers in Home Location Register (HLR).
Answer printout HLR SUBSCRIBER TRACING DATA is received.
This command can be initiated from up to 16 Input/Output (IO) devices simultaneously.
Only one command can be initiated when parameter ALL is specified.
The order does not remain after system restart.
3 Examples
3.1 Example 1
HGSTP:IMSI=ALL;
The trace data for all mobile subscribers, are printed.
3.2 Example 2
HGSTP:IMSI=1234567890;
The trace data for IMSI 1234567890 are printed.
4 Printouts
4.1 Check Printout
No.
4.2 Procedure Printouts
NOT ACCEPTEDfault type
Fault type:
FUNCTION BUSYThe function is busy.
FORMAT ERRORThe command or a parameter was incorrectly specified.
UNREASONABLE VALUEdetails
The parameter was specified with an unreasonable value.
FAULT CODE 13 IMSI NOT DEFINED
The IMSI is not defined.
FAULT CODE 73 SUBSCRIBER DISCONNECTION IN PROGRESS
Disconnection in progress for that mobile subscriber.
FAULT CODE 75 FUNCTIONALITY NOT SUPPORTED BY THIS EXCHANGE
The functionality connected to the command is not supported by this exchange.
FAULT CODE 232 TRACE DATA NOT INITIATED FOR THIS IMSI
No trace data are initiated for the specified IMSI.
4.3 Answer Printouts
HLR SUBSCRIBER TRACING DATA
4.4 Result Printouts
This command has no result printouts.
5 Logging
No.
6 Command Category Group
Recommended value 0 (H'0)
7 Command Receiving Block
HSTRA
8 Glossary
HLR Home Location RegisterIMSI International Mobile Subscriber IdentityIO Input/Output
9 References
9.1 Printout Descriptions
HLR SUBSCRIBER TRACING DATA
9.2 Application Information
HTRAN
COMMAND DESCRIPTION 2/190 82-CNT 238 0034 Uen D
HGSDP
© Telefonaktiebolaget LM Ericsson 2001
Home Location Register, Subscriber Data, Print
1 Format
1.1 Command
/ \
/ \ | / \ | |MSISDN=msisdn...| | |ALL | | | | | |SUDA| |HGSDP:+IMSI=imsi... + |,+SSDA+ |; | | | |LOC | | |CONNECTED | | |PDP | | \ / | \ / | \ /
1.2 Parameters
ALL All subscriber dataCONNECTED All connected subscribersIMSI=imsi International Mobile Subscriber Identity (IMSI)
See the Application Information for block HTRAN. LOC Subscriber location dataMSISDN=msisdn Mobile Station ISDN Number (MSISDN)
See the Application Information for block HTRAN. PDP Packet Data Protocol (PDP) context subscriber data
Application system dependant parameter.SSDA Permanent and supplementary service subscriber dataSUDA Permanent subscriber data
2 Function
This command prints subscriber data for mobile subscribers in Home Location Register (HLR).
Answer printout HLR SUBSCRIBER DATA is received.
Associated answer printouts are also received depending on the parameter given:
PERMANENT SUBSCRIBER DATA , SUPPLEMENTARY SERVICE DATA, LOCATION DATA and PACKET DATA PROTOCOL CONTEXT DATA answer printouts are received when parameter ALL is entered.
PERMANENT SUBSCRIBER DATA is received when parameter SUDA is entered. PERMANENT SUBSCRIBER DATA and SUPPLEMENTARY SERVICE DATA answer
printouts are received when parameter SSDA is entered. LOCATION DATA answer printout is received when parameter LOC is entered. PACKET DATA PROTOCOL CONTEXT DATA answer printout is received when
parameter PDP is entered.
This command can be initiated from up to 16 Input/Output (IO) devices simultaneously.
The order does not remain after system restart.
3 Examples
3.1 Example 1
HGSDP:CONNECTED;
Subscriber data for all connected subscribers are printed.
3.2 Example 2
HGSDP:IMSI=1234567890,ALL;
All subscriber data for the mobile subscriber with IMSI 1234567890 are printed.
3.3 Example 3
HGSDP:IMSI=1234567890,SUDA;
Permanent subscriber data for the mobile subscriber with IMSI 1234567890 are printed.
3.4 Example 4
HGSDP:MSISDN=3417429013,SSDA;
Permanent and supplementary service subscriber data for the mobile subscriber with MSISDN 3417429013 are printed.
3.5 Example 5
HGSDP:MSISDN=3417429013,LOC;
Location data for the mobile subscriber with MSISDN 3417429013 are printed.
3.6 Example 6
HGSDP:CONNECTED,LOC;
Location data for all connected subscribers are printed.
3.7 Example 7
HGSDP:MSISDN=3417429013&3417429015,SSDA;
Permanent and supplementary service subscriber data for the mobile subscribers with MSISDNs 3417429013 and 3417429015 are printed.
3.8 Example 8
HGSDP:IMSI=3417429013&3417429015,PDP;
PDP context data for the mobile subscribers with IMSIs 3417429013 and 3417429015 are printed.
4 Printouts
4.1 Check Printout
No.
4.2 Procedure Printouts
NOT ACCEPTEDfault type
Fault type:
FUNCTION BUSYThe function is busy.
FORMAT ERRORThe command or a parameter was incorrectly specified.
UNREASONABLE VALUEdetails
The parameter was specified with an unreasonable value.
FAULT CODE 183 PARAMETER NOT SUPPORTED BY THIS EXCHANGEdetails
The parameter is not supported by this exchange.
4.3 Answer Printouts
HLR SUBSCRIBER DATALOCATION DATAPACKET DATA PROTOCOL CONTEXT DATAPERMANENT SUBSCRIBER DATA
SUPPLEMENTARY SERVICE DATA
4.4 Result Printouts
This command has no result printouts.
5 Logging
No.
6 Command Category Group
Recommended value 0 (H'0)
7 Command Receiving Block
HSDA
8 Glossary
HLR Home Location RegisterIMSI International Mobile Subscriber IdentityIO Input/OutputMSISDN Mobile Station ISDN NumberPDP Packet Data Protocol
9 References
9.1 Printout Descriptions
HLR SUBSCRIBER DATA
LOCATION DATA
PACKET DATA PROTOCOL CONTEXT DATA
PERMANENT SUBSCRIBER DATA
SUPPLEMENTARY SERVICE DATA
9.2 Application Information
HTRAN