equipment lesson
TRANSCRIPT
-
8/3/2019 Equipment Lesson
1/15
CADWorx Video Training Series
Module Five Modeling 3D Equipment
Written by Anthony W. Horn 2011CAD Training Technologies, LLC Houston, TX USA 304
Module Five
Modeling 3D Equipment
In this Module you will model a variety of 3D equipment, using the CADWorxEquipment Modeler program.
Youll see how to model Pumps, Vertical Vessels, Exchangers, Filters, Flat PlateExchangers, and Steam Traps.
-
8/3/2019 Equipment Lesson
2/15
CADWorx Video Training Series
Module Five Modeling 3D Equipment
Written by Anthony W. Horn 2011CAD Training Technologies, LLC Houston, TX USA 305
The EquipmentBuilder is dialogdriven to simplifymodeling
You can buildhorizontal or verticalmodels
Modeling a Pump
When you model a pump, the main concerns are the location of thesuction and discharge nozzles in relation to the pump base. Whenthese are right, the rest of the pump is usually not too much of aconcern. Modeling the base, motor , shaft, and coupling are
important mainly for verifying you have room around the pumpfor its operation and installation, and also to establish a spatialvolume for the pump to occupy. Then you can see if somethingmight be clashing or interfering with parts of the pump.
Watch the opening sections of the video and then start your model.
To start the process, have Equipment running and
1. Click New
2.
Enter in the name: P-1000.3. Click Horizontal (for the orientation).
-
8/3/2019 Equipment Lesson
3/15
CADWorx Video Training Series
Module Five Modeling 3D Equipment
Written by Anthony W. Horn 2011CAD Training Technologies, LLC Houston, TX USA 306
Placing the maincomponents
In pumps, the mainconcern is locatingthe nozzles correctly
Then youll4. Click the Components tab and5. Click the first four buttons on the pump tool bar (see video).
You can follow the videos, then pause them at certain points,and fill out your dialog boxes with values as shown in thefollowing figures.
The video will show you exactly how to get the dischargenozzle oriented correctly.
-
8/3/2019 Equipment Lesson
4/15
CADWorx Video Training Series
Module Five Modeling 3D Equipment
Written by Anthony W. Horn 2011CAD Training Technologies, LLC Houston, TX USA 307
The body and baseof a pump model canshow you if there isadequate clearance
from other objects inthe model
The only tricky part to a pump is getting the discharge nozzle oriented correctly (seevideo). Also, you will have to do some adjustments to get the nozzles positioned asneeded in relation to the base. The video will explain that as it goes along.
Details on the discharge when you click Distance.
-
8/3/2019 Equipment Lesson
5/15
CADWorx Video Training Series
Module Five Modeling 3D Equipment
Written by Anthony W. Horn 2011CAD Training Technologies, LLC Houston, TX USA 308
Other values used in the pump model
:
-
8/3/2019 Equipment Lesson
6/15
CADWorx Video Training Series
Module Five Modeling 3D Equipment
Written by Anthony W. Horn 2011CAD Training Technologies, LLC Houston, TX USA 309
This model willcontain vessel parts,nozzles, andplatforms
Modeling a Vertical Vessel
In this section youll model the vertical vessel named 35-450.
This will be an interesting example, because youll model thevarious components that make up the vessel, as well asplatforms and nozzles.
Note: The top platform has been modified from the video.See the details in the later section of this lesson.
-
8/3/2019 Equipment Lesson
7/15
CADWorx Video Training Series
Module Five Modeling 3D Equipment
Written by Anthony W. Horn 2011CAD Training Technologies, LLC Houston, TX USA 310
Use the dialog boxesfor data as you gothrough the videos
Dialog boxes makeupdating the modeleasy and dynamic
Start the video for the lesson, and watch the first section. Then
you can pause it and do some of the steps it shows. Go back and forth from the video to CADWorx Equipment and work you way along step by step.
As you progress through the videos you will enter in values inthe dialog boxes as shown.
-
8/3/2019 Equipment Lesson
8/15
CADWorx Video Training Series
Module Five Modeling 3D Equipment
Written by Anthony W. Horn 2011CAD Training Technologies, LLC Houston, TX USA 311
-
8/3/2019 Equipment Lesson
9/15
CADWorx Video Training Series
Module Five Modeling 3D Equipment
Written by Anthony W. Horn 2011CAD Training Technologies, LLC Houston, TX USA 312
-
8/3/2019 Equipment Lesson
10/15
CADWorx Video Training Series
Module Five Modeling 3D Equipment
Written by Anthony W. Horn 2011CAD Training Technologies, LLC Houston, TX USA 313
-
8/3/2019 Equipment Lesson
11/15
CADWorx Video Training Series
Module Five Modeling 3D Equipment
Written by Anthony W. Horn 2011CAD Training Technologies, LLC Houston, TX USA 314
You can savemodels and easilymodify them forother clients
In CADWorx, youcan also transfermodel and designdata back and forthbetween CADWorxand PVElite
Equipment ModelingModeling Heat Exchanger
In this lesson you will model a heat exchanger. The HeatExchanger youll model looks as shown.
You could model the exchanger yourself, step-by-step if needed.It would be a matter of naming it, setting the orientation tohorizontal, and clicking components from the first toolbar toarrange them (elliptical head, cylinder, body flange, stiffeningring, etc.).
-
8/3/2019 Equipment Lesson
12/15
CADWorx Video Training Series
Module Five Modeling 3D Equipment
Written by Anthony W. Horn 2011CAD Training Technologies, LLC Houston, TX USA 315
1. Start the Equipment module in CADWorx Plant.
2.
On the Placement Tab,3. Click New4. Fill out the name: EX-1000
5. Set the Orientation to Horizontal.
Follow along with the video and model the exchanger as it shows.
The values youll need to fill out, as you watch the video, are shown in thefollowing figures.
Save the drawing regularly, and replay the video if you need to watch certainsections more than once.
-
8/3/2019 Equipment Lesson
13/15
CADWorx Video Training Series
Module Five Modeling 3D Equipment
Written by Anthony W. Horn 2011CAD Training Technologies, LLC Houston, TX USA 316
-
8/3/2019 Equipment Lesson
14/15
CADWorx Video Training Series
Module Five Modeling 3D Equipment
Written by Anthony W. Horn 2011CAD Training Technologies, LLC Houston, TX USA 317
-
8/3/2019 Equipment Lesson
15/15
CADWorx Video Training Series
Module Five Modeling 3D Equipment
Written by Anthony W. Horn 2011CAD Training Technologies, LLC Houston, TX USA 318
Experiment with other parts of the exchanger. Try some different measurements andnotice how the system handles your input.