engineering mechanics solutions
TRANSCRIPT
Solutions Manual
For
Engineering
Mechanics
Manoj Kumar HarbolaIIT Kanpur
1
Chapter 1
1.1 Rotational speed of the earth is very small (about radians per second). Its
effect on particle motion over small distances is therefore negligible. This will not be
true for intercontinental missiles.
1.2 The net force on the (belt+person) system is zero. This can be seen as follows. To
pull the rope up, the person also pushes the ground and therefore the belt on which he
is standing. This gives zero net force on the belt. For the person, the ground pushes
him up on the feet but the belt pulls him down when he pulls it, giving a zero net
force on him.
1.3 A vector between coordinates (x1, y1, z1) and (x2,y2,z2) is given by
. Thus (i), (ii) and (iv) are equal.
1.4 The vectors are (i) (ii) (iii) (iv)
1.5 (i) The resultant vectors are , and
(ii) The resultant vectors are , and
1.6
1.7 On each reflection, the sign of the vector component perpendicular to the reflecting
mirror changes.
1.8
2
A
BBA
B
A
AB
z
xO
vy
The fly is flying along the vector from (2.5, 2, 0) to (5, 4, 4). This vector is
. The unit vector in this direction is .
The velocity of the fly is therefore
.
1.9 After time t, the position vectors and of particles A and B, respectively, are
Their velocities and are given by differentiating these vectors with respect to
time to get
Velocity of A with respect to B is obtained by subtracting from
1.10 For rotation about the z-axis by an angle
It is given that . Therefore
3
1.11 Component of a vector along an axis is given by its projection on that axis. This is
obtained by taking the dot product of the vector with the unit vector along that axis.
Thus
Also
Substituting the expression for Ax, Ay and Az completes the proof.
1.12 (i) Dot product of two vectors and is
This gives the dot product of the first vector of problem 1.4 each of the other vectors
to be 4, 2 and 25.
(ii) Cross product between two vectors and is
Taking to be the fourth vector and to be the first, second and the third vector
gives the cross products to be
1.13 If the angle between two vectors is , the cosine of this angle is given by
. Thus
Between (i) and (ii)
Between (i) and (iii)
Between (i) and (iv)
Between (ii) and (iii)
Between (ii) and (iv)
4
Between (iii) and (iv)
1.14 Vector can be written as
Similarly
Taking the dot product between the two vectors and using the formula ,
where is the angle between the two vectors, we get the answer.
1.15 Magnitude
Similarly
Equating the two gives which implies that the two vectors are perpendicular
to each other.
1.16
This comes out to be equal to and
1.17 From the expression for it is clear that it is equal to the determinant
Interchange of two rows in a determinant changes the sign of the determinant. This
implies
5
thereby proving the equalities in problem 1.16.
1.18
Therefore
The x-component of
On the right hand side above, add and subtract to get
Do the same manipulation for the other components to get
1.19 ( i)
(ii) Body diagonal from the origin to the opposite corner is .
This vector is perpendicular to the vectors AB, AC and BC in the plane, because
its dot product with each one of them vanishes. This shows that the diagonal is
perpendicular to the plane.
6
Another way to see this is to find a vector perpendicular to the plane by taking
cross product of any of the two vectors from AB, AC or BC, and show that it is
parallel to the body diagonal. For example taking the cross product of AB and AC
gives
which is parallel to the body diagonal.
(iii) If the angle between OA and AB is then
This gives . Note that we have taken dot product with the vector BA rather
than AB because we wish to keep less than . In the same manner we get the
angle between OA and AC also to be .
1.20 The problem is to be solved exactly in tha same manner as done in example 1.3 by
replacing the position vector by the velocity vector and the velocity vector by the
acceleration.
1.21 Position vector
Velocity vector
Acceleration
1.22 (i) In reference frame 2, the components of vector at time t are given
in terms of its components in frame 1 by formula (1.10) as
Here are time-independent because vector is constant in frame 1.
Differentiating with respect to time, we get
7
(ii) From (i) it is clear that
1.23 Done in later chapters
1.24 Magnitude of a vector quantity is fixed. This means
Differentiating both sides with respect to time we get
Since is not zero, the equation above implies that and are
perpendicular to each other.
An everyday example is a particle moving in a circle. The magnitude of its position
vector is a constant and therefore its velocity, which is the time-derivative of its
position vector, is perpendicular to the position vector.
1.25
The area of triangle OAB is given as
This is maximum at
1.26 Let the angle between the z axis and the vector be . Then the component OB is
. Thus the magnitude of OB is . However, its direction is
perpendicular to the plane containing the z axis and the vector OA. To get the proper
8
direction we again take cross product of with . The component in the z
direction is given as . Thus the vector OA is . In general
can be replaced by .
9
Chapter 2
2.1 (i)
(ii) Since the element of length y is in equilibrium, we have
Using Taylor series expansion for T(y+y), which gives
And taking limit leads to the differential equation for T(y). The equation is
Solution of this equation is
where C is the integration constant. This is determined by using the fact that at the
lose end (y=L) of the rope, the tension is zero. This gives
and
10
yL
yT(y)
T(y+y)+
2.2 Torque
It is given that and the force has magnitude 50N and acts in the direction of
vector . Thus the force is 50 times the unit vector in the direction of the given
vector. This gives
With this the torque is
2.3 (a)
(b) The centre of the rod is at (3, 2)
The right end is at position and the force at this end is
The left end is at position and the force at this end is
Torque with respect to the origin =
100N
100N
11
Torque with respect to the centre of the rod =
Torque with respect to the left end of the rod =
Torque with respect to the right end of the rod =
(c) Torques about all the points are equal because the net force on the rod is zero.
2.4 (a)
(b) gives
(i)
Net torque about A is zero, which gives
(ii)
Equation (ii) gives
This substituted in equation (i) gives
30N0.5m
A 3m
1m
B
70N 120N
TA TB
12
2.5 Component of force in the plane perpendicular to the axis is at a distance of R
from the axis.
Therefore the torque about the axis is
2.6 Free-body diagram of the block
N1, N2 and W are three forces in a plane. Thus they must pass through one common
point for equilibrium. So the equilibrium conditions are only the force conditions.
gives
gives
Solution of these two equations is
N2
N1
W
13
2.7 Free-body diagram of the plank
Free-body diagram of the block
If the rod makes angle with the horizontal then
and
(a) To get the horizontal force F, we first calculate the normal force N on the rod. To do so,
we calculate the total torque about the hinged end of the plank and
equate it to zero. This gives
Now we balance the horizontal forces on the block to get
(b) Force balance on the plank
N
0.2m
Rx
100N
2m
1mRy
F
Nground
N
14
This gives
Minus sign in front implies that the direction is opposite to that shown in the free-body
diagram above.
2.8 Free-body diagram of the rod
Balancing the vertical forces gives N1 = W = 50N
Balancing the horizontal forces gives N2 = F
Balancing the torque about the centre of gravity gives
leading to
2.9 Free body diagram of the painting
W
N2
F
N1
15
Force balance equations give
and
N1 and N2 are equal because the component of torque perpendicular to the wall must vanish.
This gives
N1=N2=25N
Balancing the component of torque parallel to the wall taken about the lower end of the
painting gives
giving
2.10 We first calculate the forces at the ends of the rod. These forces are applied by the
supports. After finding the forces on the rod, we then calculate the forces and the
torques applied by the wall on the supports.
Free body diagram of the rod
N1+N2
T
W
Fx
W
N1 N2
16
Free body diagrams of the left and the right supports
The forces on the rod satisfy which gives
Taking torque about the left end and using gives
This gives
Now balancing vertical forces and the torque on the supports gives
For the left support F1=20N and
For the right support F2=15N and
2.11
35N
60cm
140cmN1 N2
1
F1
N1
5cm2
F2
N2
5cm
17
To find the force applied by the plastic block, we balance torque about the upper left corner.
This leads to
Balancing the vertical forces gives Ry = 40N
Balancing the horizontal forces gives Rx = 30N
Negative sign means that the direction of Rx is opposite to that assumed in the free-body diagram
above.
Free-body diagram of the pole
Ry
40cm
40N
60cm
Rx
N
18
Balancing the vertical forces on the pole gives N = 40N
There is no net horizontal force and the two horizontal forces give a couple = 300.4 = 12Nm
Balancing the torques on the pole about the ground gives = 300.4 = 12Nm
2.12 Free-body diagram of the table
To find Ny, we balance the torque on the table about its left hand edge to get
30N
40cm
30N
40N
N
j
i
90cm
Nx
NyRy
Rx
20N
19
By balancing the vertical forces, we get . The negative sign tells us that the force is
direction opposite to that shown above.
Free-body diagram of one of the rods
Free body diagram of the entire system
To get Nx, we balance the component of the torque coming out of the paper on the entire system
about the lower hinge. This gives
The negative sign again tells us that the direction of the force is opposite to that shown.
Balancing the horizontal component of the force on the table then gives
Sx
Sy
2Rx 30
2Ry
2Sy
Nx
Ny
30
90cm
20N2Sx
20
Note: The net force on each rod on its upper end is which is along
the rod as it must be for the equilibrium of a rod held at its ends.
Balancing the horizontal and vertical components of forces on each rod gives
Thus the net force on each rod is 10N compressive.
2.13 Free body diagrams of the two side portions and the portion AC over the pulley:
Tension TA and TC at both ends of the portion over the pulley is the same because the torque
about the centre must vanish. This gives
Free body diagrams of the portion AB and BC
TA
TATC
TCN
F
gLML1
gLML2
gL
RM
21
Notice that Torque of the normal reaction about the centre of the cylinder vanishes because for
each small portion of the rope over the cylinder, the normal reaction is radial. Thus T A (or TC)
and TB cannot be equal because they together provide a torque to balance the torque due to the
weight of the rope. Balancing the torque about the centre on AB gives
Thus if the net force by the cylinder on the rope is Neff at an angle from the horizontal then by
force balance
Note that Neff acts at a point different from the centre of BC because on different infinitesimal
portions it is different.
2.14 The support does not apply any torque about the x-axis. All other components and torques
are balanced by the support.
2.15 When forces are applied at two points of the rod, force balance demands that the force be
equal and opposite. However two such forces acting at two different points will give rise to
a couple moment. The couple moment is zero only if the forces point along the rod (see
figure below)
Neffx
TA
TB
gL
RM2
Neffy
Neffx
TC
TB
gL
RM2
Neffy
22
2.16 Let cables OA and OC make angle 1 and OB and OD angle 2 with the vertical. Then
balancing the vertical forces gives
The sine of the angles is easily calculated to be
This gives T=14050N
2.17 The torque direction is given by the direction of cross product , which is
perpendicular to . This implies there is no component of the torque in the direction of .
2.18 The net force on the plate is
Therefore the force that must be applied to the plate to keep it in equilibrium is
. Since there are only three forces acting on the body, they must all pass
through the same point so that their net torque is zero. This is shown in figure below.
Couple moment non-zero Couple moment zero
23
The force is at an angle from the line DC. Thus it
does not pass through O and intersects with side AD and diagonal BD of the square. Therefore:
(i) It is not possible to keep the square in equilibrium by applying the third force at O.
(ii) It is possible to keep the square in equilibrium by applying the third force at a point
on BD.
Equation of BD with O as origin is
Equation of line along which the third force acts is
Solving the two equations gives
This gives the distance of point O = 0.125a
And from B =
(iii) It is clear that for equilibrium, the force can be applied only on AD and BC.
D C
BA
O
24
Chapter 3
3.1 For the three trusses shown, m = 21, j = 12. Thus they all satisfy 2j-3 = m. Thus they are
all simple trusses.
3.2 Showing that pin E is in equilibrium
There are five forces acting on E of which two (FE and ED) are horizontal, two (CE and
the external load) are vertical and one (BE) is at an angle. We wish to check if the
horizontal and vertical forces add up to zero. It is solved in 3.1 that
Since all the forces are tensile, they all pull the pin. In addition there is the external load
of 5000N vertically down.
The net horizontal force is
Similarly the net vertical force is
3.3 (i) The truss has 4 members and 4 joints. Number of force balance equations therefore is
8 (2number of joints). On the other hand, number of forces available is only 7
(3+number of members), which implies that the truss will not be stable and will collapse.
In terms of stability condition which implies that the truss will collapse.
(ii) If we add one more member to the truss, i.e make m = 5, then is satisfied
and the truss becomes stable and a simple truss. Let us add a member across AC.
To find forces in each member we start by first finding the forces applied by the
external supports. The free-body diagram of the truss is as follows:
25
The direction of the forces applied by the external supports has been anticipated as
shown. To find ND, we balance torque about A to get
Now balancing the vertical and horizontal forces on the truss gives
NAx = 0 and NAy = 1875N
The negative sign again tells us that the direction of the force is opposite to that
shown.
We begin to apply the method of joints from point D since at this point there are two
unknown forces FAD and FCD. Assuming these forces to be tensile gives the free body
diagram of joint D as follows
Balancing the vertical forces on point D gives
CB
5000NNAx
NAy
ND
A D
60FAD
FCD
6875N
26
The negative sign shows that the force FCD is compressive and not tensile as assumed.
Balancing the horizontal forces on point D gives
The negative sign again shows that the force FAD is compressive and not tensile as assumed.
Next we go to point A and balance the forces there. The free body diagram of point A is
In drawing the figure above, we have shown the direction of FAD according to it being a
compressive force.
The length of rod AC is = m
So
Now balancing the horizontal forces at A gives
and balancing the vertical forces at A gives
Solving these two equations gives FAB = 0 and FAC = 4390N
Since the sign of FAC is positive it is in the same direction as assumed and therefore tensile.
Now we can easily see that force FBC will be zero because point B is under equilibrium under
only two forces FAB and FBC and FAB has already been determined to be zero. Thus FBC = 0.
Thus all the forces are now determined. They are
FAB
60
3969N
1875N
FAC
27
FAB = 0 FAC = 4390N (tensile) and FBC = 0.
Finally to check our answer we make the forces at point C and see if they all balance. The
free body diagram of point C is
Balancing the horizontal forces at C gives
Balancing the vertical forces at C gives
This indicates that our answers are correct.
Note: We see that FAB and FBC both vanish. This implies that members AB and BC may
not bee needed for the truss. This is true because with just three members AD, AC and
CD (m=3) there are only three joints (j=3) and the truss satisfies the condition
for it to be a stable structure.
3.4 Free body diagram of the truss
7939N
60
5000N4390N
28
Since point C is in equilibrium under one known and two unknown forces, both unknown
forces can be determined easily. The forces on C look as follows
Balancing the vertical forces at C gives
With this implies FAC = 54N (compressive)
Balancing the horizontal forces at C gives
The only force left is at AB. We calculate this by balancing forces acting on pin A, which
look as follows.
Ry
B 30cm
20cm30N
A
C
N
Rx
FBC
30N
FAC
29
This gives
Additionally we can also solve for the normal reaction N and the forces Rx and Ry. These
are
N = 54N, Rx = 45N, and Ry = 30N
3.5 Rod AB provides a vertical force to hold pin A. However if it is removed and the vertical
force is provided by a fixed pin joint, the structure will remain stable because we need
3j=6 forces for equilibrium of 3 joints; two of these are provided by the fixed supports
and two by the two members. The forces in the members remain the same. So do the
forces by the two support except that the fixed point at A also provides a vertical fore of
30N that was earlier provided by member AB.
3.6 Free-body diagram of the truss
FAC
FAB
N
30
Since pin D has only two unknown forces acting on it, we can start our calculations from this
point onwards. The forces on D are
It is immediately clear that
FAD = 0 and FCD = 100 N (tensile)
Next we go to pin C and balance the forces there. The forces acting on C are
C
N
Rx
Ry
100N
A
B
D
FCD
100N
FAD
31
Balancing the vertical forces at C gives
(compressive)
Balancing the horizontal forces at C then gives
(tensile)
Next we go to pin A. The forces there are as follows
Balancing the vertical forces at A gives
(tensile)
Balancing the horizontal forces at A gives
N=100N
Finally balancing forces at pin B will give the external forces
Rx = 100N and Ry = 100N
3.7 Free body diagram of the truss is as follows
FAC
100N
FBC
N
FAB
N2100
32
(i) There are 4 reaction forces at the supporting pins at A and B. In addition the forces
generated by the members of the truss equal 6. This makes the total number of forces
available = 10. The number of joints in the truss is 5 that require exactly 10 number
of forces for equilibrium. Thus the truss is a stable one.
(ii) It is also statically determinate since the number of forces available is equal to the
number of equations to be satisfied for equilibrium.
(iii) First we find Nx by balancing the torque about point B. This gives
We now begin by balancing the forces at point D
Balancing the vertical forces at D gives
(compressive)
DC
A
B
500N
Rx
Ry
Nx
Ny
E
FED
500N
FCD
33
Balancing the horizontal forces at D then gives
(tensile)
Nest we go to pin E because it has two unknown forces acting on it. The forces are as
follows
Balancing forces at E gives
(compressive)
(tensile)
Next we go to pin at A. The forces there are
Balancing the forces gives
(compressive)
and
(tensile)
Finally we go to point C where only one force FBC is unknown. The forces on C are
FAE
N
FCE
FAC
Ny
500N1000N
34
Balancing the horizontal forces at C gives
FBC=1000N
As a final check, the value for FBC gives the horizontal force Rx by pin B on the truss to be
1000N and vertical force Ry to be zero. This is consistent with the overall equilibrium of the
truss when it is treated as a system by itself.
3.8 Since each member of the truss weighs 50N, at each pin we take the load by each pin at
that point to be 25N. The free body diagram of the truss is as follows; here each small
arrow pointing down indicates the weight of the truss member, acting at its centre.
We firs find NE. To do this we balance the torque about B. This gives
FAC
FBC
500N
500N
CB
1000NA
DE
NE
NBxNBy
35
This immediately gives, by balancing forces on the entire truss
NBx = 0 and NBy = 925N
The negative sign showing that the force I opposite to the direction assumed in the figure
above.
We begin at pin D as there are two unknown forces there. The force diagram on pin D is as
follows (there are two members meeting at pin D that give a load of 225=50N there)
Balancing the forces gives
(tensile)
and
(compressive)
Next we go to pin E. The forces acting there are (including 325=75N from 3 members)
Balancing the forces gives
(compressive)
FCD
1050N
FDE
FAE
2275N
FCE +75N
1050N
36
and
(compressive)
Next we go to pin A. The forces acting there are (including 325=75N from 3 members)
Balancing the forces gives
(tensile)
and
(compressive)
Net we move to point B where the forces are (including 225N=50N from two members)
This immediately gives
FAB = 975N (compressive) and FBC = 0
As a final check, one balances all the forces at C and sees that they all balance properly. This
implies that the answers obtained by us are correct.
FAB
1050N
FAC
75N
FAB
FBC
925N
50N
37
3.9 Free body diagram of the truss with the weight of each member included. The free body
diagram is then as follows.
By balancing the torque about A we get
Balancing the vertical and horizontal forces on the truss, this gives
and
For calculating force in members, we take the weight of each member shared equally at each
joint. The forces on A are (including the weight of two members)
Balancing the forces at point A
Next we go to point F. The forces at point F are (including the weight of three members)
F E D
CB
5000N
NA ND
Nx
A
N3
11750
FAF
FAB500N
38
Balancing the forces here gives
Next we go to point B since now there are only two unknown forces there. At point B the forces
look as follows (including the weight of four members)
Balancing the forces
Negative sign above means that the direction of the force is opposite to the one assumed. So
FBC = 5083N (compressive)
N3
10250
FBF
FFE
750N
750N
FBC
4832N
FBE1000N
39
We next consider point C and balance the forces there. The forces at point C are (including
750N form the weight of three members)
Balancing the forces
Next we go to pin D where the normal reaction is N and balance the forces there. The
force diagram there is (including 500N form the weight of two members)
It is easily seen that the vertical forces balance at this point. This points to the correctness of our
calculations so far. Balancing horizontal forces then gives
FED = 5083 N (tensile)
750N
FCE
5083NFCD
500N
7188N
FED
N3
16750
40
As a final check we should check whether all the calculated forces balance at pin E. The forces
at pin E are (including the weight of four members)
All these forces balance as can be seen by calculating the net x and y components of the
forces. Thus our calculations are correct.
3.10 Free body diagram of the truss
Taking torque about B we get
Balancing the horizontal and vertical forces now gives
NBx = 1000 N and NBy = N
Negative sign above means that the direction of the force is opposite to the one assumed.
1000N
2357N
N
4333N
5083N
5000N
E
D
C
B
A
1000N
2000N
NBx
NBy
NE
41
We begin at pin D. The forces there are
In the diagram above
Balancing the vertical forces gives
(compressive)
Balancing the horizontal forces gives
2789N
Next we go to pin E. The forces there are
Balancing the vertical forces gives
(compressive)
Balancing the horizontal forces gives
N (compressive)
1000N
FED
FCD
2000N
FAE
FCE
N
2683N
42
Next we go to pin A. The forces there are
Balancing the vertical forces gives FAC = FAB.
Balancing the horizontal forces gives
This also means that
FAC = 895N (tensile)
Now we go to pin C. The forces there are
The vertical forces are already balanced here. Balancing the horizontal forces gives
To check our answers, we finally balance the forces at pin B and see if they all balance there.
At pin B the forces are as follows
FAC
FAB
1192N
895N
FBC
895N
2789N
43
It is easily seen that all the forces above balance. So our answers are all consistent.
3.11 The weight of the road = volume of the roaddensityg
= 128.3200010
= 576000N
This weight is divided equally between the two trusses on the sides. Thus only
288000N is supported by each truss.
Weight of the members of the truss = 135000
= 65000N
Total weight supported by each truss therefore is = 353000N
Free body diagram of the truss is
From the balance of forces, is clear that
895N
1000N
N
1596N
NAxH G F E
DCB
A
353000N
NAy NE
44
Let us now consider forces at each pin one by one. Each pin has the following forces
acting on it: The weight of the road divided over 5 pins, which is ;
the weight of the members at that pin; and the forces applied by the members.
Let us now balance forces at point E. The forces on pin E are (including the weight of
the members)
In the figure above
Balancing the vertical forces in the figure above gives
(compressive)
Balancing horizontal forces then leads to
(tensile)
Next we consider pin D. The forces on pin D are (including the weight of the
members)
57600N
FEF
176500N
FDE5000N
45
Balancing horizontal forces then leads to
(compressive)
Balancing the vertical forces gives
(tensile)
Next we look at pin F. The forces there are (including the weight of the members)
Balancing the vertical forces in the figure above gives
(compressive)
Balancing horizontal forces then leads to
(tensile)
By symmetry of the problem, forces on the members to the left of member CG will be
exactly the same as on the corresponding members to its right. The only force that we
now have to calculate is on member CG. For this we consider point G. Two horizontal
FCD
142375N
FDF
7500N
57600N
FGF
106400N
FCF10000N
85425N
46
forces at G are by HG and GF and are equal to 114525N each. The forces at point G are
then given as
This gives FCG = 65100N
Finally we check our answer at point C. The forces there (including the weight of 5
members meeting there) are
As is easily seen, the forces at C balance and therefore our calculations have been
consistent throughout.
3.12 Free body diagram of the truss is as follows
57600N
FCG
7500N
114525N114525N
65100N
48500N 48500N
FCF12500N
85425N85425N
47
Here the distances and the angles are
AH = HG = GF = FE = 2.5m BH = DF = 1.25m (similarity of triangles)
Balancing torque about point A gives
Thus NA = 2000N and RA = 0
Now that the external reactions have been determined, we can go about calculating the forces
in the members. We start with pin E because there are only two unknown forces there. The
forces at E are
Balancing the vertical forces in the figure above gives
(compressive)
Balancing the horizontal forces gives
N (tensile)
RA
NA
1000N
E
D
C
B
A FGH
2000N
NE
FEF E
1000N
FDE
48
Nest we go to pin D. The forces there are
Balancing the forces gives
(compressive)
FDF = 0
Next we go to point F where the forces are as shown below.
Balancing the forces gives
FGF = 2000N (tensile) FCF = 0
Pin G is considered next. Since the forces there are only vertical and horizontal, even
without making the forces there, we immediately can write
FCG = 0 and FGH = 2000N (tensile)
Next we consider point A where two members AB and AH meet and therefore there are two
unknown forces. The forces there are
D
2236NFDF
FCD
2000N
FCF
FFGF
0N
49
Balancing the vertical forces gives
(compressive)
Balancing horizontal forces then gives
(tensile)
Next we go to point B. Here there are four forces acting and each pair (FBH and 2000N; and
FBC and 4472N) has two forces in opposite directions. Thus without solving the detailed
force balance equations, we can directly write
FBH = 2000N (compressive) and FBC = 4472N (compressive)
Next we go to point H and balance the forces there. The forces there are as follows
By balancing the forces at H, it becomes clear that (tensile)
Finally the answers are checked at C. The forces at C are as shown below
FAB
FAHA
2000N
45
FCH
4000N2000N
H
2000N
50
As is easily seen, the horizontal a n vertical forces all balance at C. Thus our answers are all
correct.
To calculate the forces by method of sections, we make a cut through the truss so that it
passes the concerned members. In the present case we take the following section of the truss
and show various forces on that section.
In the figure above, FCH is determined easily by taking torque about A since the torque due to
FCB and FGH both vanish about A. This gives
(tensile)
To find FCB, we balance the vertical component of the forces to get
Negative sign here means that the force is opposite to the direction assumed and therefore is
compressive in nature.
Finally, balancing the horizontal forces leads to
1000N
D
2236N4472N
N22000
2000N
FCB
B
A H
2000N
FCH
FGH
51
(tensile)
3.13 The free-body diagram of the truss on one side is as follows (Notice that the weight of the
truck is equally divided between the two trusses)
We first calculate NE by balancing torque about A. This gives
This gives NA = 12.5 kN and RA = 0
To find forces in members CD and DG, we make a cut through CD, DG and GF. This looks
like the following
RA
NA
NE
50kN
H G F
E
DCB
A
FGF
37.5 kN
50kN
FGD
F
E
DFCD
52
To find FGF, we balance torque about point D about which the torques due to FCD and FGD
vanish. This gives
(tensile)
To obtain FCD, we take torque about point where FDG and FGF intersect, which is point G.
This leads to
(compressive)
Now we balance the horizontal and vertical forces on the truss. Balancing horizontal forces
gives
Negative sign here means that the force is opposite to the direction assumed and therefore is
compressive in nature.
To find the forces in the members BC and BG, we make a cut through the members BC, BG
and HG as follows and then calculate the forces.
To obtain FBC, we take torque about point where FGH and FBG intersect, which is point G.
This leads to
(compressive)
Next we find FGH by taking torque about B. We get
(tensile)
Finally we get FBG by balancing vertical and horizontal forces. Horizontal force balance
gives
(tensile)
12.5 kN
HFGH
FBCB
A
FBG
53
Finally to find FCG, we make the following cut through the truss
Since the vertical forces all balance, this implies FCG = 0.
Further, the horizontal forces are also balanced.
12.5kN37.5kN
50kN
H G F
E
DFCGB
A
54
Chapter 4
4.1
4.2 Since the block is in equilibrium under three forces, the three forces must pass through
the same point. Thus the normal reaction will be at the point where the arrow showing
the weight meets the inclined plane. This is shown below.
4.3 The free body diagram of the block is as follows
Applied force
Frictional force
sN
Fmax
f
mg
θ
N
55
Balancing the horizontal forces gives
Balancing the vertical forces gives
Since the maximum frictional force , for equilibrium we should have
4.4 We consider two different situations when the weight on the table is about to move to the
left or to the right. When it is about to move to the left, its free body diagram will look
as follows
By equilibrium conditions, we have
N = 50g
f + mg = 10g
f
N
mg
F
10g
N
50g
f
mg
56
Since
We have
Thus the minimum value of m is 5kg when the frictional force is at its maximum pointing to the
right. As m is increased above 5kg, frictional force becomes less and less, eventually changing
direction and attaining its maximum value pointing left. In that situation, the free body diagram
of the block on the table is as follows.
In this situation, the equation for horizontal force balance is
f + 10g = mg
This coupled with leads to
Thus
4.5 Taking the x axis along the plane and the y axis perpendicular to the plane, the free-body
diagram of the block looks as follows.
50g
f
10g
N
mg
57
The equations describing equilibrium in the X and the Y directions are
The first equation implies that
Taking g = 9.8ms2, the value of F for different values of F is
4.6 Free body diagram of the box when it is about to move (i.e. the frictional force is at its
maximum) is shown below
N
F
F
30º
30º
XY
100g
N
a
bh
F N
mg
58
When the box is about to move, the friction is at its maximum and is equal to N. The force F
also equals N at this point. This creates a couple that is counterbalanced by the couple formed
by the weight of the box mg and N (=mg). This is the reason that N shifts towards the direction
of the push. However, the maximum couple moment that can be created by mg and N is .
Thus for the box not to topple, the couple created by F and the friction should remain less than
. Thus implies
4.7 suppose each break show makes an angle at the centre as shown below
The force F is assumed distributed uniformly over the shoe. Then the torque due to the
frictional force will be
With two shoes therefore, the torque would be
4.8 It is given that mass M is balanced by mass m. The contact angle is π. Since each time the
string is wound once more around the rod, the mass M that can be balanced by m becomes
twice as large, we have
This gives = 0.11
59
4.9 Neglecting the length of the rope passing over the pulley, we have mass on one
side of the pulley that is balanced by mass on the other side. Thus we have
4.10 As the weight is put, it has a tendency to move down. Hence
the frictional force will be in the counterclockwise direction. Thus if the tension in the rope
on the spring balance side is T1 and that on the weight side is T2 then
Now it is given that T1 = 5g and T2 = mg. Thus we get
An interesting possibility exists if a person had pulled the weight down and then slowly
brought it to equilibrium. In that case the tension will work in the other direction and
However we have not considered this possibility.
4.11 There is a range of M2 that exists because frictional force can act with its maximum value
in one direction to the maximum in the other direction. Largest value of M2 is when the
mass M1 is about to slide up the plane. The free body diagram of M1 in that case is as
follows
f
N
M1g
T
60
When the mass M1 is about to slide up, we have
The contact angle between the rope and the pulley is
Since the rope has a tendency to move clockwise, the frictional force due to the pulley will be
acting counterclockwise. Thus we have
The other extreme is when the mass M1 is about to slide down the plane. In that case the free
body diagram of M1 is
Thus we have
Now the rope has a tendency to move counterclockwise, the frictional force due to the pulley
will be acting clockwise. Thus we have
4.12 Free body diagram of the tire when it is loaded and is about to roll is as follows
f
N
M1g
T
61
Balancing the vertical forces gives
Balancing the horizontal forces gives F = f
Balancing torque about the centre of the wheel gives
NW
F
f
62
Chapter 5
5.1 Consider a composite surface of total area A made up of N different surfaces. Then the
coordinates of the centroid satisfy
If the area of each surface is then
Now in the definition of the centroid, the integrals can be performed separately over each surface
so that we can write
This immediately gives
5.2 By symmetry it is clear that XC = 2. We are nevertheless going to prove it below. We first
calculate the area of the surface. It is
Substituting we get
To calculate Xc, we take vertical strips of width dx on the
surface at distance x from the origin and then calculate
63
O X
Y
x
Thus
Similarly to calculate YC, we take horizontal strips of width dy at height y and calculate
At height y, the strip extends from x1 to x2. These
points are given by the equation
Therefore
We thus have
Substituting so that , we get
This gives
Thus the centroid is at
5.3 One curve (call it curve 1) in this problem is the same as that in the problem
above. The other curve (curve 2) is
64
x1 x2OX
Y
y
The y-axis of curve 2 is thus 4 times curve 1. The area of curve 2 is therefore . Similarly
the x coordinate the centroid of curve will remain at 2 but the y coordinate will be .
Thus we have
The area A for which we wish to obtain the centroid is obtained by removing surface
formed by curve 1 from the surface formed by curve 2. We thus have
5.4 Trapezoidal loading is shown in the figure below
The total force on the beam will be equal to the area under the curve. Thus the total force is
equal to
This load will be acting at the centroid of the area. Thus it acts at
X
f(x)
X1 X2
w2
w1
65
Adding and subtracting and in the numerator we get
5.5 From figure 5.14, for a plate of width w
Similarly, from figure 5.15
66
This gives from formula 5.9
which is equivalent to the depth given by formula (5.17)
5.6 Loading on the tank door is triangular as shown below
The average pressure is the pressure of water at the centroid of the submerged part. Thus the
average pressure will be
Thus the total force due to the water pressure is
This force acts at the centroid of the loading that is triangular in this case. Thus it is at a distance
below point A.
We now apply equilibrium conditions to the door. This leads to
0.25m
NB
NA
N1
153.125N
19.6N
0.5m
67
5.7 The rectangular surface looks as follows
To find Ixx, we take a strip (see figure above) of width dy parallel to the x-axis and calculate
Similarly to find Iyy, we take a strip (see figure above) of width dx parallel to the x-axis and
calculate
To find Ixy, we take a small square (see figure above) of size dxdy parallel and calculate
by symmetry of the inegrand.
b
a
X
Y
68
5.8
From the figure
From the formula for transformation of area moments (taking X and Y axis as in the problem
above) we get
Similary
b
Y’
X’
a
O
69
and
5.9
To calculate IXX we take a horizontal strip of width dy at y (see figure) for dA and calculate
dyybbaydAyI
b
bXX
2222 2
Taking , we get
Similarly for IYY, we take a vertical strip at x for dA and calculate
Taking , we get
b
a
X
Y
70
And by symmetry
We now calculate the moments and product of inertia about a set of axes rotated by an angle
with respect to the original one and with the same origin. Thus
Similarly
Product of inertia is calculated using the formula
5.10
71
To calculate IXX we take a horizontal of width dy strip at y (see figure) for dA and calculate
To evaluate the integral, we substitute so the integral is transformed to
Now substituting , we get
Similarly for IYY, we take a vertical strip of width dx at x for dA (see figure) and calculate
X
Y
O x1 x2
y
X
Y
O
x
72
Taking we get
Now , and . This gives
5.11 Product of area about the origin O is given as
If the centroid is at O’ which has the coordinates and the coordinates of a point with
respect to O’ are then
Therefore
O
(x0,y0)
X
Y Y’
X’
73
However, by definition of the centroid
Thus
5.12 Consider the moments and product of inertia of a square about a set of axes parallel to its
sides and passing through its centre.
For this set of axes
Now by the formula
Ix’y’ will always remain zero because of the equality of Ixx and Iyy irrespective of the angle of
rotation of the new set of axes x’y’. Thus any set of axes passing through the centre is the
principal set of axes.
5.13 The formulae for the moments of inertia in rotated frames are
a
Y
X
74
Taking the second derivative of these expressions with respect to , we get
Thus the two derivatives have opposite signs. This implies if one of them is a maximum, the
other one will be a minimum.
75
Chapter 6
6.1 (i) (a) and (d) are the virtual displacements because these are the only ones consistent with
the constraint that the block can move only in the vertical direction.
(ii) Suppose the strech is y0. In that situation, the forces on the block are as shown
Now a virtual displacement gives a displacement of in the vertical direction. Taking it in
the vertically up direction gives the virtual work to be
Equating this to zero gives
6.2 Figure below shows the students and the plank on a wedge and a possible virtual
displacement of the system.
It is clear that as long as the point on the wedge does not move, the only possible displacement is
the rotation of the plank about this point and the system has only one degree of freedom. For the
ky0
mg
x (3-x)
40g50g
30g
76
virtual displacement shown, the displacement and the virtual work done by various forces is as
follows:
Since the net virtual work must vanish for equilibrium, we have
6.3 (i) Since the number of parameters required to describe the system is 1, the number of
degrees of freedom is 1. We choose it to be the angle , the rod makes from the vertical. A
virtual displacement will be to change by .
(ii) To apply the principle of virtual work, we need to calculate the virtual work done by various
force when is changed to +. For this we first write the coordinates (x, y) of the tip of the
rod and yCG of the centre of gravity of the rod with respect to the pivot point. These are
As is changed to +, these coordinates change and the changes are given by
Thus the total virtual work done by the external forces – 2g at the CG, 20g at the tip, both in the
positive y direction, and T at the tip in the positive x direction – is
20kg
T2kg
1.5m
77
Equating this to zero gives
6.4 To find the forces applied by the bricks, we treat these forces as external. For only vertical
motion, there are two degrees of freedom. One is the vertical displacement of the centre of
gravity and the other the rotation of the plank about the CG. Equivalently, we can take the
vertical displacements of the ends A and B as the virtual displacements. We choose the
second option because this is related directly to the forces applied by the bricks. The plank
in equilibrium and virtually displaced is shown below
Now the vertical virtual displacement of different points is
Point A :
Point B :
Centre of gravity of the plank :
Athlete :
Thus the total virtual work done is
500N
NA
2m100N NB
y2
y11m
1.5m
78
Equating the virtual work to zero and therefore the coefficients of each independent
displacement (y1 and y2) to zero gives
NA=175N and NB = 425N
6.5 (i) Constraints on the system: length of the strings holding the masses is fixed
(ii) There is only one degree of freedom. This can be understood as follows. There are
three variables needed to describe the system: The distance of two masses and one
pulley from the ground. However there are two constraints: To of the strings have
fixed lengths. Thus only one variable is left to change freely.
(iii) In terms of the lengths shown in the figure
The constraint that the longer string has fixed length is expressed as
The constraint that the shorter string has fixed length is expressed as
(iv) The constraint forces are the tension in the two strings. It is by these tensions that
the constraints are maintained.
(v) To apply the method of virtual work, we make a virtual displacement of mass 1.
The corresponding displacement of mass 2 is then . However, since there is only
y2
M2
M1h1
y1
h2
79
1 degree of freedom, we will finally express in terms of to apply the method
of virtual work. The virtual work done in these processes is
Notice that the two virtual displacements are not independent. Therefore we should not
conclude that M1=M2=0 for equilibrium. To apply the method, we first express the virtual
work in terms of only .
From the first constraint equation, since h1 if constant,
From the second constraint we have
Substituting these in the expression for the virtual work gives
Equating this to zero then gives, for equilibrium
6.6 (i) Since the two blocks are free to move in one dimension without any constraint, the
number of degrees of freedom for the system is 2.
(ii) The system in equilibrium is shown below. At equilibrium spring on the left is
stretched by x1 and the total stretch of the two springs together is by x2. Thus spring
on the right is stretched by (x2x1). Thus force on mass m1 is to the left and
to the right. These two forces must be equal for equilibrium but we wish
to obtain this by applying the principle of virtual work. Similarly the two force
acting on m2 are F and to the left. Again these two forces must be equal
for equilibrium and we will obtain this by applying the principle of virtual work.
80
As the mass m2 is moved by a virtual displacement , let us assume that mass m1 moves
by . Then the virtual work done will be
Equating this to zero and therefore the coefficients of and to zero gives
and
This gives and .
6.7 (i) There is only one degree of freedom. Although the piston moves in the vertical direction
and the wedge in the horizontal direction, their movements are connected because the piston
moves on the surface of the wedge.
(ii) Normal reactions on all the surfaces are the constraint forces. In the present context, the
constraint force specific to the piston’s movement on the surface of the wedge is the normal
reaction of the wedge surface on the piston.
(iii) if the distance of the middle line of the piston is at a distance a from the origin, its
height is y and the distance of the left edge of the wedge is x (see figure) then the
constraint is expressed as
F
k1 k2m1 m2
x1 x2
81
Now the method of virtual work is applied by considering x as the free variable, varying it by x,
and equating the total virtual work to zero. The virtual work is
Equating the coefficient of x to zero gives
6.8 When the equilibrium angle is , the distances of various points (see figure) , taking A as the
origin are as follows
The force on the two points B and D due to the spring is
to the left on B and to the right on D
F
m
a
yx
82
It is clear that we need only one parameter to specify the system. Thus there is only one
degree of freedom. Now let us make a virtual displacement by changing by . In that
situation
Thus the total virtual work done as is changed by is
Vanishing of the virtual work then implies
Or equivalently
If then the solution is . For very small value of therefore we have ,
where x is very small. Substituting in the equation above, we get
W
A
B D
C
x
y
83
Since is small, we get by Taylor series expansion
Thus the equation for equilibrium is
Or to a good approximation
Thus
6.9 (i) Even if we consider only one dimensional motion, we would require two variables, one
the angle that the bar makes with the vertical and the other describing the position of the
mass. However, the two are connected by a rope. Hence the two variables cannot vary
independently since the length of the rope is foxed (constraint). Therefore there is only one
degree of freedom in the system.
(ii) The constraint is the length of the rope remaining constant. It is enforced by the
tension that develops in the rope. This tension makes the movement of the bar and
the mass restricted. Thus it is the tension in the rope that is the force of constraint.
(iii) A virtual displacement would be to displace the bar by an angle from its
equilibrium position. Since the length of the rope is fixed, the midpoint of the bar
moves by the same distance as the mass connected to the rope. Therefore the tension
does positive work at one end of the rope and exactly equal but negative work at the
other end. The sum of the work done by the tension then vanishes.
(iv) Let us say we make a virtual displacement of the bar by turning it counterclockwise
by an angle from the vertical. Then the end of the rod moves by l in the
84
direction of the force. At the same time, the virtual displacement of the mass is
equal to the movement of the midpoint of the bar. Thus the mass moves by
opposite to the gravitational force (see figure)
The net virtual wok therefore is
Equating this to zero then gives
6.10 Initially the bars are at 90. The weight has a tendency to fall down so the torque applied is
such that it tends to pull the weight up. Thus is a virtual displacement of angle is made
in the direction of the torque, the weight will be lifted up by the corresponding distance y.
The corresponding virtual work done by the torque is and the corresponding work by
the gravity is Wy. By the method of virtual work then we have
This gives
m
F
85
Next we calculate the relationship betweeny and . As the rod is rotated by angle , the
length of the horizontal diagonal decreases by . If the corresponding angle at the
vertical corner changes from 90 to 90+α, then we have (see figure)
Change in the length of the horizontal diagonal
=
This should equal so we have
As the angle changes the length of the vertical diagonal changes by
Thus we have
This gives
6.11 (a) For the motion in a plane, the orientation of the rod can be described by the
displacement of its centre of mass and the angle it has rotated by about its CM. Or
W
(90+α)
86
equivalently the displacement of its two ends is sufficient to describe its orientation. Thus
the degrees of freedom is 2.
(b) We take the vertically down displacement of the two ends as the virtual displacement as
shown in the figure.
Let the centre of mass be at a distance from the left hand end of the rod. In that case,
the centre of mass moves down by . The virtual work
done by the springs in such a virtual displacement is and respectively while
that by the weight of the rod is . Thus equating the net virtual work to
zero gives
Now equating the coefficient of each independent displacement to zero gives
y2
y1
yCM
87
Chapter 7
7.1 For Cartesian coordinates (x,y), the planar polar coordinates are and
. If y<0 and x<0, 270>>180 and if y<0 and x>0, >270.
Unit vectors are given by
and
7.2 At each point the velocity is given as . Thus for (iv) for a
particle at (-2,-3), the velocity is
7.3 The two points with polar coordinates and and the corresponding
vectors are shown in the figure below
(i) As is clear from the figure, the angle between the vectors and is . This also the
angle between unit vectors and and unit vectors and . Therefore
2
1
(21)
88
Similarly, angle between and is and that between and is .
Therefore
(ii) Similarly, from the figure
(iii)
7.4 The trajectory of the projectile is shown schematically in the figure below. The
horizontal distance from the origin to the point of highest elevation (height 1.25m) is
. The vertical component of the velocity at this point vanishes while the
horizontal component is . Similarly, the vertical component of the
acceleration is 10ms-2 vertically down. Also shown in the figure are unit vectors in the
radial and the tangential directions at the highest point and on the ground.
From the figure it is clear that for the point of highest elevation
Therefore the radial and tangential components of the velocity at the highest point are
Similarly the radial and tangential components of the acceleration are
1.25m
89
On the ground, the radial unit vector points towards positive x direction and the
tangential unit vector is in the negative y direction. Thus the radial component of the
velocity is its x component and the tangential component is its y component. Therefore
Similarly, since the gravitational acceleration on the ground is in the negative y direction,
its radial and tangential components are
7.5 The position of the particle at time t is shown in the figure below.
The polar coordinates of the particle at time t are given as
Therefore
This gives the velocity in polar coordinates as
Differentiating the velocity vector gives
2t
1
2ms-1
90
Now substituting and , we get the acceleration above to be
zero.
7.6 (i) Kepler’s second law states that the rate of the area swept by the radius vector is
constant. This can be expressed as (see figure for the symbols used)
constant
Now differentiating the equation above with respect to time gives
The expression on the right is the tangential acceleration. Thus Kepler’s second law gives
tangential acceleration to be zero.
(ii) Since the tangential acceleration is zero, the force is only in the radial direction.
Acceleration in the radial direction is
We differentiate the orbit equation with respect to time to get
Sun
r
91
Since is constant, differentiating the equation above once more with respect to time, we get
This gives
This shows that the force is proportional to r2.
7.7 It is given that
which gives
Now write and differentiate it twice with respect to t to get
This gives
Substitute this in to get
Multiplying and rearranging terms gives
The equation does not appear to be easily ingrable.
7.8 It is given that and
92
(i) Since , integrating the equation for gives
or equivalently
(ii)
If the velocity vector is at 45 to the radius vector, we have
This gives
Squaring both sides gives
OR
This is equivalent to
(iii) Radial acceleration zero implies
which leads to
giving
This also gives the distance from the origin to be
7.9 Free body diagram of the bead when its radius vector is making an angle (increasing as
the particle slides down) from the vertical is shown below
93
Taking the components of the forces in the radial and tangential directions and equating these
to mass times the radial and tangential components of the acceleration, respectively, gives
In the radial direction
In the tangential direction
Since the particle moves on a path of constant radius , we have
When substituted in the equations above, this gives
Now using , we get from the second equation above
which gives upon integration
When substitutes in the equation , this gives
7.10 The free body diagram of the bead at equilibrium is shown in the figure below.
R
mg
N
94
The horizontal components of the normal reaction N provides the centripetal force while the
vertical component balances the weight of the bead. Thus
Dividing the first equation by the second one gives
The slope of the curve is also equal to . Thus
This gives
and
7.11 Since , we have
;
Thus and
7.12 We know that
Therefore
mg
N
95
Similarly
7.13 Since
We get from the solution
From , we get
Now from we get
And from we get
7.14
96
(i) The tension in the outermost string provides the centripetal force for the outermost bead.
Let the tension in this string be T1. Then
Similarly, centripetal force for the second bead from outer end is provided by the difference
in the tension T2 in the second string and tension T1 in the first string. Thus
Extending further
and so on. In general we can write for the ith string from the outside,
This is then easily seen to be
(ii) Now we generalize the result of part (i) to a rope of length L and mass per unit length
λ. To make the transformation from the problem in part (i) to this problem, we
consider the mass of each bead to be distributed over the connecting string whose
length we take to be vanishingly small i.e. . Thus we have
and
Substituting this in the expression for Ti above, we get
ml
T1T2
97
On taking limit , we then get
To get this answer by considering the rope directly, we take a small portion of the rope of
length at a distance x from the centre O. The centripetal force to it is provided by the
difference in the tension at its two ends, as shown in the diagram below
Then
This gives the differential equation
The solution of this equation is
where C is the integration constant. With the condition that the tension vanishes at x=L, we
then get
7.15 Consider a small section of the rope making a small angle at the centre of the
loop. The force at its two ends due to the tension in the rope is shown in the diagram
below
T(x) T(x+x)
98
For small angle the forces at the ends give a net force towards the centre which is equal to
This provides the required centripetal force for the segment. Therefore
7.16 The relevant coordinates and the free body diagrams of the two masses are shown
below
We treat the mass m using the polar coordinates as shown in the figure. The total number of
unknowns in the problem are : y coordinate of mass M, polar coordinates of mass m and
tension T in the string. The corresponding equations are
TT
/2
Tsin(/2)
r
y
M
m
Mg
T
mg
T
99
And the constraint equation
7.17 (i) After time t, the end of the rod that was at the origin has moves by a distance .
Thus the relationship between the x and y coordinates will be
(ii) Free body diagram of the bead is shown below
Thus the equations of motion are
From the constraint equation
Thus
which gives
Thus
Or
θθ
N
100
(iii) Integrating the equation above with the condition gives
Thus the bead will take time to reach the lower end.
7.18 Suppose the lower corner with angle is at the origin at t=0. Then if the position of
the mass is (x, y) at time t, the relationship between these coordinates is
if the acceleration of the wedge is A. This implies
(i) Now if the mass falls vertically down, which gives i.e. the
wedge accelerates to the right with acceleration . The interpretation is
quite simple: when the wedge moves by horizontal distance , the mass
should move vertically down by and the relationship between the two at
minimum acceleration is .
(ii) For the particle not to move with respect to the wedge, we have
which implies
.
The free body diagram of the mass is as follows
101
Thus we have by the conditions above
which gives
7.19 From example 7.9
This gives (assuming )
Similarly
This gives
Y
θX
N
102
Thus if mass m starts from height h, it will take time
And at this time the speed of the wedge will be
7.20 The coordinates used in solving the problem are shown in the figure below
Let the tension in the string be T. The equations of motion for the two masses are
And since the pulley P3 is massless, we have
Thus we have four unknowns y1, y2, y3 and T but only three equations. One more equation is
provided by the constraint equation. The constraint is that the length of the string is a constant.
If the heights of the two fixed pulley are h1 (for P1) and h2 (for P2), the constraint is expressed as
P1
P2
P3m
my1
y2
y3
T TT
Th1
h2
103
or equivalently as
Now adding the equations of motion for the two masses gives
On substituting and from the equations above, we get
This gives
The general solution of the equation above is the sum of its homogeneous solution yh(t) and the
particular solution yp(t). We have
Here A and B are two constants to be determined by the initial conditions and . Thus
the general solution is
Now the initial condition is
These give
Thus
This immediately gives through the equation
104
This gives
This is easily integrated. Since it is gives that and , we get
In exactly tha same manner we get
7.21 (i) Wedge m3 is free to move only in the horizontal direction; m1 and m2 move both
horizontally as well as vertically. Thus we would have had 5 degree of freedom.
However, there are three constraints: The length of the string is fixed, mass m1 moves
only in the vertical shaft and mass m2 moves on the plane of the wedge. These
constraints reduce the degrees of freedom to 2. Thus there are only two degrees of
freedom.
(ii) The origin and the coordinate axes chosen to describe the motion are given in the figure
below. Also shown are the free-body diagrams of the three masses
m2
m1
m3
x1
y1
x2
x3
y2
105
We see that there are in total 8 unknowns: x1, y1, x2, y2, x3, N1, N2, N3 and T. The equations of
motion are:
These are the equations of motion. In addition there are three constraint equations.
In the above, h is the height of the wedge. There are a total of nine variables and nine equations.
Of these equation (vi) is not relevant for the motion since the wedge moves only in the horizontal
direction.
Equations (i), (iii), (iv) and (ix) give
which gives
This is the equation expressing momentum conservation in the horizontal direction.
Similarly equation (iv) and (v) along with (ii) give
m2gm1g
m3N1 N1
N2 N2
N3
TT
TT
m2g
106
Now substituting for from (viii) and from (vii) and using (ix), we get
Which is equivalent to
Now using , we eliminate from the equation above to get
This gives
And using , we then get
Now using equation (viii) we get
Using equation (vii), we get
As , we get
7.22 Consider two parts of the rope x and (L-x) in length. The free body diagrams (showing
only the horizontal forces) of the rope and these two parts are shown below
107
Since the rope is moving with constant speed, there is no net force on the rope or any part of
it. Thus from the free body diagram of the rope
From the free body diagram of the left portion of the rope
Or from the free body diagram of the right portion of the rope
It is also instructive to solve the problem by considering a small portion of length dx at
distance x from the left and balancing the forces there to get a differential equation for T(x).
The free body diagram of such a portion is as given below
With the condition that T(L) = 0, the equation above can be integrated to get
xF
Friction
F
Friction
T(x)
T(x)
Friction
T(x)
Friction
T(x)+dT(x)
dx
108
7.23 The force applied should be such that the frictional force on mass m is sufficient to balance
its weight. Free body diagrams of the two blocks are shown below
If the entire system is moving with acceleration a then
This gives
If mass m is not falling then
Thus
For m=16kg, M=88kg, =0.38 and g=9.8ms-2, we get
mgM
Ffriction
NN
friction
Mg Normal reaction
109
7.24 The forces on the bead are: Its weight, normal reaction NV in the vertical direction and
normal reaction NH in the horizontal direction. Thus the free body diagram of the bead is
as follows (assuming the rotating arm is going into the page)
These force provide the radial and the tangential acceleration given by
Since the rod is rotating with a constant angular speed , we have
(i) If the bead is stationary at r=R, we have
This gives
Since , we get for stationary bead
(ii) If and negligible weight of the bead, we have
The minus sign for the friction shows that since the bead slides outwards, the frictional force in
inwards. The equation describing the motion of the bead is then
Assuming a solution of the form and substituting it in the equation above we get
Solution of this equation gives
mg
NV
NH
friction
110
Thus the general solution is
Here A and B are to be determined by the initial conditions that .
Thus
The solution is
Thus the distance of the bead from the center is given as
7.25 The solution for the distance travelled by the particle is
For k=0, we can’t substitute this directly in the formula since we are dividing by k in the
expression above. Thus we take the limit . In this limit, the first nonzero term we get is
This gives
7.26 The equation of motion for the particle is
111
The solution of the homogeneous equation
is
Here A is a constant to be determined by the initial conditions. The particular solution is
Therefore the full solution is
Now the initial condition is . This gives
Thus
This is easily integrated to get y(t) also. Thus
When the ball reaches the highest point, its speed is zero. If this time is tup, then
This gives the height h to be
112
If the total time of flight is T then T=tup+tdn, where tdn is the time taken to come down from
the highest point. At time T, y(T)=0. Therefore
Thus tdn will be given by solving
To understand whether tup is larger or tdn is larger, let us see the time change in the limit of
very small k. In that case (up to order k)
And tdn is given by solving
This gives
Therefore
113
A comparison shows that tup is smaller than tdn. This makes sense because the while coming
down, the average speed is smaller since the particle has lost energy due to viscosity and
continues to do so.
This also gives the total time of flight to be (up to order k)
However, this approximation will be valid only if
5.27 It is given that and . Therefore . It is also
given that .
(i) Height = Range =
(ii) When , from the expression derived in the problem above, we get with the initial
vertical speed
Height =
Substituting the values , we get
For k=0.1, Height = 202m
For k=0.2, Height = 172.3m
To find the range, we first fine the total time of flight and then use formula derived in example
7.13 to find the horizontal distance travelled. From the solution of the previous problem, we
know that the time of flight T is given by solving
For k=0.1, this gives
114
Since the time of flight without drag is , and as the result of the problem
shows the time of flight becomes smaller for , we tabulate T and the right hand side of the
equation above to find T for
It is clear from the Table above that the expression on the right was smaller than T till T=13s and
becomes larger at 12.5s. Thus the time of flight will be between 13 and 12.5s. A little more
tabulation gives T=12.8s.
Substituting this in , we get Range = 669m
Since , we get tdn= 6.75s. This confirms numerically that time
taken to come down is greater.
For k=0.2, the equation to determine the time of flight is
Making a table like above gives T=11.8s and Range T
14 13.62
13.5 13.29
13 12.93
12.5 12.58
115
(iii)
(iv) When drag is introduced, it is the range that is affected much more than the height.
(7.28) In the problem above, we have already found the range for . Let us now take the
case of k=0.1 and find the range for and .
For , the equation
beomes
or
and gives
T=11.7s.
This gives a range of
116
k=0
k=0.1
k=0.2
= 678m.
Thus for , the range increases.
For , the equation
beomes
or
and gives
T=13.8s.
This gives a range of
= 641m.
Thus for the range decreases.
The two calculations above show that for maximum range, the projectile should be launched at
an angle less than .
The reason for this is as follows. Since the horizontal speed reduces as the projectile moves, it
should cover a larger distance in the initial part of the flight. For this it is better to have a
relatively larger horizontal component of the velocity compared to the case when there is no
drag. Thus the angle should be smaller than .
(7.29) In this case the drag force is proportional to the square of the speed. So the equation of
motion will be given as follows for the motion up and motion down (taking vertically up
direction to be the positive y direction)
Motion up
Motion down
Since we are only interested in height, we change to to get the speed as a
function of the vertical distance of the ball from the ground. The first equation in that case is
117
The solution of this equation is the sum of the solution of the homogeneous equation
and a particular solution . These solutions are
and
Here A is a constant to be determined from the initial conditions. The full solution therefore is
The initial condition is that . This gives
This the speed of the ball as it moves up is
At the maximum height h, the speed becomes zero. Therefore
This gives
Now we consider the motion for downward motion. This can be rewritten as
Again the solution of this equation is the sum of the solution of the homogeneous
equation and a particular solution . These solutions are
and . Thus the complete solution is
Now the initial conditions are . This gives, with
118
This gives
If the final speed is vf, then
Note that of k=0 then The answer can also be written as
119
Chapter 8
8.1 Since there is no external force on the system in the horizontal direction, the total momentum
in the horizontal direction is conserved.
Initial momentum in the horizontal direction = momentum of the carriage + momentum of rain
=
=
Final momentum of the system after time t =
Here vf is the final velocity. Equating the two moment gives
8.2 Since the water leaking out of the carriage still has a horizontal velocity equal to the velocity
of the carriage, total momentum of water after it came out for time t is =
If the initial amount of water in the carriage was m0, then the initial momentum of the system
(carriage + water in it) =
If the aped of carriage (with left over water in it) after time t is vf, then by momentum
conservation
8.3 Exactly like in problem 8.2, there will be no change in the speeds of the two bicyclists. This
is easily done by considering the momentum of the two friends before and after the books
are given by one of them to the other person. Consider the person giving the books. Her
momentum before transferring the books is . After she gives the books, let her speed by
vf. Then by momentum conservation
Similarly, for the person receiving the books
8.4 Conserve momentum after the first bullet has been fired. Initial momentum is 0. Let the
velocity (since the motion is one dimensional, we write only the symbol for it, the direction
is taken care of by the sign) of the gun after the bullet is fired be v1. Since the relative
velocity of the bullet when it leaves the gun is u, and the bullet leaves the gun when the gun
120
is already moving with v, bullet’s speed ug with respect to the ground is calculated as
follows:
Therefore momentum conservation gives
Now the momentum of the gun and bullets in it is
Now let the speed of the gun after the second bullet is fired be v2. Then momentum
conservation gives
Similarly one can now show that if the speed after the third bullet is fired is v3 then
Generalizing this we get after N bullets have been fired
8.5 (i) Momentum of the system = sum of the momentum of each particle
= kg ms1
(ii) velocity of the centre of mass = total momentum/total mass
8.6 (i) acceleration of the CM
121
(ii) No, the acceleration is not in the same direction as the momentum of the CM.
8.7 If the base of the cylinder is in the xy plane, as shown in the figure, the x and y coordinates
of the CM are (0, L/2). We thus have to calculate the z coordinate of the CM.
To obtain the z coordinate of the CM, consider a rectangular sheet of thickness dz at height z, as
shown in the figure below.
If the density of the material that the cylinder is made of is , the z coordinate of the CM, by
definition, is
L
R
x
y
z
z R
122
To evaluate the integral, we substitute and . This gives
8.8 (i) CM of a cone shown in the figure below
The CM is on the axis of the cone by symmetry. To calculate its height, we take a thin disc of
thickness dz at height z. By similarity of triangles, it radius r is given by
If the density of the material that the cone is made of is , then the position of the CM is given
by
It is reasonable that the location of the CM is more towards the base since larger mass of the
cone is concentrated there.
R2
h
zr
123
(ii) Hemispherical bowl of radius R is shown in the figure below.
The CM will be on the line passing through the centre of the base. To calculate its height zCM, we
take a ring of height dz at height z. According to the figure
and ,
If the mass per unit area for the shell is , then the mass dm of the ring is
Thus
8.9 Given N particles of masses mi (i=1-N) with total mass at positions (i=1-N),
position of their CM is given as
r
R z
124
Now let us make m subsystems of these masses with number of particles N1, N2, N3……Nm in
them. Then we have the mass of each subsystem as . The position of the CM can
then be written as
By definition of the CM we have for the position of each subsystem .
Thus the expression above can be written as
This shows that the CM of the system can be calculated by treating each susbsystem as a point
particle of mass Mi located at the CM of each subsystem.
8.10 To find the CM, we will treat the cone and the hemisphere as two subsystems. It is also
clear by symmetry that the CM will be on the extended axis of the cone. Taking the axis
as the z direction with z = 0 at the base of the cone, we have
Assuming the entire system is made of a material of uniform density, we get
8.11 Since there is no external force on the system in the horizontal direction, the position of the
CM will remain unchanged as the small block moves from one side to the other. Taking
horizontal direction to be the x-direction, let the position of the CM when the block in on
125
the left be X1 and let it be X2 when the block is on the right. Then the poison of the CM of
the block is (X1R) and (X2+R), respectively. Since the CM does not move, we have
This immediately gives
8.12 When the ball is compressed, it looks like shown in the picture below
The radius r of the circular area of contact for x<<R is
Thus, if the pressure in the ball remains unchanged, the force that the ball applies on the wall is
8.12 As a photon hits the surface, it gives it an impulse proportional to its momentum. If it gets
absorbed, the impulse and if it is reflected then . And the force by the
stream of photons hitting the surface will be where n is the number of particles hitting the
surface per second. If the cross-sectional area of the parallel beam of light is a, then
Thus the pressure P
R
Rx
126
(i) when the light is completely absorbed
(ii) when light is perfectly reflected
8.14 By equation (8.42b), the force on the planar surface will be equal to momentum
transfer per unit time. On hitting the surface, the component of momentum perpendicular
to the plane becomes zero while that parallel to the plane remains unchanged. Thus all the
momentum that water stream carries perpendicular to the surface is transferred to it. The
momentum carried by the stream of water per second is
Its component perpendicular to the surface is
When the water stream hits the surface, it makes an elliptical cross sectional area on the
surface because the surface is slanted. The major axis of the ellipse is =
And the minor axis remains the same as
Thus the cross-sectional are of the ellipse is =
Thus the pressure on the surface =
8.15 At steady state flow let the mass flow rate from the upper portion of the hour-glass be
. If the height through which it falls before hitting the lower surface is h then the
amount of mass in the air is the rate at which the mass is falling and the time it takes
for it to reach the bottom. Thus it is and its weight is . Thus the hour
glass should have weighed less by this amount. However as the sand hits the bottom,
it transfers momentum to the hour glass that exactly compensates for the weight in the
127
air. This is shown as follows. As the mass hits the bottom, its speed is . Thus
the momentum it transfers to the bottom per second is .
8.16 Consider equation (8.43) for the rocket.
Now since the mass coming out leaves the rocket with , we have
This is because when the mass leaves the rocket, it has already achieved velocity
. This gives in the equation above
8.17 Example (8.9) using equation derived above. The example is solved exactly as done
in the text except that in applying the equation derived above, each
time the bullet is fired. This immediately leads to equation (8.50) and the rest is the
same as done in the example.
8.18 (i) Force needed to hold the chain is equal to the force required to hold the part of the
chain hanging vertically. This force is =
(ii)If the chain is to be pulled at a constant speed v, its mass increases at the rate of .
This gives momentum change per unit time = . This is the additional force required
to provide momentum. Thus the total force is . This is also seen easily by the
rocket equation
Now it is given that . This substituted in the rocket equation
immediately gives the result derived above.
(iii) The rocket equation, with is
128
If at a time t, the length of the chain on the table is x then and
. Thus the rocket equation can be rewritten as
This is integrated as
Upon integration this gives
Upon solving this gives
8.19 Since the peg is frictionless and the length of the portion of chain passing over the
peg is negligible, the other portion has length (Lx) and the tension in the chain is the
same throughout. Taking the tension to be T, the equation of motion for the two
portions is (see figure)
129
Adding the two equations to eliminate T gives
This equation is also obtained by direct application. Since the total mass being moved is
M, the net force is and the acceleration is .
The solution for the equation above is a sum of the solution of the homogeneous equation
and the particular solution . The solution of the homogeneous part is
Where A and B are two constants to be determined by the initial conditions. The full
solution is
x(t)
TT
130
The initial conditions are . This gives . This give
the solution for x(t) to be
8.20 (i) Since the pressure inside the box is p, and the force is unbalanced over an area S,
the force on the box will be pS.
(ii) The acceleration of the box will be
(iii) In the simplest calculation, the rate at which the molecules are coming out in one
second will be those contained in a cylinder of height , where is the average
speed in the x direction in the rms sense. Thus the rate at which the gas will be
leaking out is where n is the number density of molecules and m the mass
of each molecule.
(iv) Equation (8.45)
In our case so
by equation (8.40)
8.21 By the rocket equation . If the mass of the fuel is M, we have
, Mf = M. Thus we have
131
This gives
8.22 In this case the rocket equation becomes (assuming vertically up direction to be
positive)
Solution to the equation above is given by the sum of the solution for the homogeneous
part and the particular solution. This gives
A is determined by the initial condition . This gives . Thus
132
Chapter 9
9.1 Consider a frame the origin O and another frame with origin O’. Frame O’ is moving
with velocity V in the x-direction with respect to frame O. Let there be a force F act
on a particle; the force is the same in the two frames. Then by the work energy
theorem in frame O, we have
Now in the frame O’, the corresponding velocities are related to the velocities in frame O
as follows
and
and
Substituting this in the work energy theorem gives
Now is noting but the momentum change , which is the
same in both the frames. Thus . This, when substituted in the
equation above leads to
Which is the work energy theorem in frame O’.
9.2 Kinetic energy of each particle is
Thus the total kinetic energy of the system is = 0.45J
133
Momentum of the system is =
Velocity of the CM therefore is =
Thus the kinetic energy of the CM is =
Thus the kinetic energy of then particles in the CM frame is = 0.450.417 = 0.033J
This can also be checked by calculating the kinetic energy of each particle in the CM
frame, which is
9.3 Since the momentum of the system is zero, the kinetic energy of the CM = 0
9.4 Masses, velocities, moment and kinetic energies o feach particle are shown in the table
below
mi(kg) vi(ms1) pi(kgms1) KEi(J)
1 1 1 0.5
2 2 4 4.0
3 3 9 13.5
4 4 16 32
5 5 25 62.5
Thus the total mass is = 15kg
Total momentum is = 15kgms1
Velocity of the CM =
Total kinetic energy = 112.5J
Kinetic energy of CM =
Kinetic energy about the CM = 105J
134
This is easily checked by calculating the kinetic energy of each particle about the CM and
adding them all up. Thus
KE about the CM =
= 105J
9.5 From equation (9.37), we have
Thus the kinetic energy of the system
Since , we get
9.6 (a) We will be using to calculate the force. Thus ,
where C is a constant chosen according to the reference point x0, where .
(i)
(ii) To calculate the potential energy, substitute so that
to get
(iii)
135
(iv)
(b) The plots of force and potential in each of the cases above are as follows. The force is
shown on the left and the corresponding potential on the right in each case.
(i) We have taken k = 1.5. We have chosen the constant such that U(0) = 0.
(ii) The plots are drawn for a = 5
(iii) We have chosen the constant such that U(0) = max.
136
(iv)We have chosen the constant such that U(0) = 0. Notice that the average force is always
positive, i.e. pointing in the positive x-direction. Therefore the potential energy curve keeps
going down as x increase.
9.7 We use and keep the potential continuous everywhere. In the
plots the force is shown on the left and the corresponding potential on the right in each
case.
(i)
If we choose
For the plots drawn below we have chosen k = 2.
137
(ii)
If we choose U(x) = 0, C=0.
For the plots below, we have chosen k=2.
(iii)
The nature of force implies that the potential is a constant for
138
Choosing U(0) = 0 gives and
For the plots below, we have chosen k=2 and a =15.
(iv)
The nature of force implies that the potential is a constant for
Choosing U(0) = 0 gives
Thus
For the plots below, we have chosen C=250 and a =20.
139
9.8 We use . This gives
(i)
(ii)
(iii)
(iv)
(b) Plot for part (i) is straightforward; it is a constant force and linearly varying potential
Plots for part (ii) are similar to that of part (i) in problem 9.7. This has been given above.
(iii) We have chosen a = 5. The force is shown on the left and the corresponding potential
on the right.
140
Notice that the force is negative for negative x and positive for positive x. Thus it is a force
that pushes a particle away from x = 0 and the position at x = 0 is an unstable equilibrium
point. Thus when a particle is displaced slightly from this point, it will runaway to infinity.
(iv) We have chosen a = 5. The force is shown on the left and the corresponding
potential on the right.
Notice that the force is positive for negative x and negative for positive x. Thus it is a
restoring force and the position at x = 0 is a stable equilibrium point. Further the force is
varying almost linearly with x near x = 0. Thus when a particle is displaced slightly from this
point, it will perform simple harmonic oscillation.
9.9 Since all the potentials except (i) are time-dependent, only (i) is conservative.
9.10 For the block not to fall off the track, its speed v at the top of the loop should be such that
Now by the conservation of energy we have
9.11 For the potential energy we have the potential energy curve (with
parameters C = 0.5 and a =2)
141
It is clear from the curve that a particle will always experience a force in the negative direction
except at a = 2. From this it is clear that the point x = a is a point of unstable equilibrium.
For the potential energy we have the potential energy curve (with parameters C
= 0.5 and a =2)
This potential energy curve gives force opposite to the displacement, and the force is zero at x =
a. Thus this point is a point of stable equilibrium. Notice that unlike the potential energy for a
142
spring , this potential energy is quite flat near the equilibrium point (because
for . For larger displacements from x = a, the curve rises much faster
than the spring potential energy.
9.12 Let the velocities of the balls be v1 and v2 after the collision (since this is a one
dimensional motion, we are not putting vector signs on top of the velocities). Then by
momentum conservation
The first equation gives
This and the second equation implies that
Thus either v1 is zero, i.e. the first ball is not moving. This is the situation after collision.
Or v2 is zero, i.e. the second ball is not moving. This is the situation before collision.
9.13 According to the situation give, the two balls are undergoing an elastic collision (no loss
in energy) when they are moving in the opposite directions with equal speed V. Let
the mass of the lighter ball be m and that of the heavier one be M. If the velocity of
smaller ball is v1 after the collision, then by equation 9.36 (taking vertically up
direction to be positive)
In the extreme limit, when M>>m, we have
If the balls are dropped from a height h then
If after the collision the smaller ball goes to height H then
These two equations give
9.14 By momentum conservation we have
143
Totla initial energy =
Final energy =
As is clear, the final energy is less than the initial energy. Therefore some energy is lost in
the process.
Now consider a pile of beads, each of mass m, connected with strings of length l between
them. As the first bead falls over the edge, its initial speed is zero bu by the time the string
connecting it to the second bead is taut, it gains a velocity of . However, as soon
as it pulls the second bead, by momentum conservation at that instant (neglecting the
impulse due to gravity) the speed of two beads is
Now the two beads fall together and as the string connecting the second bead to the third
bead becomes taut, the energy of hse two beads is
This gives the speed of the two beads to be
Thus when the third bead is pulled over, momentum conservation at that instant gives the
speed of the three beads to be =
One can go on like this and build up the solution up to p th bead falling by recognizing a
pattern. We can also do the problem in the following way.
Suppose when the (p-1)th bead has just fallen of the edge, the speed of the beads becomes
. Then when these beads fall and the string between the (p-1) th and pth string becomes
taut, the energy of the system will be
Thus the speed of these beads just before the pth bead falls off the edge is given by
144
By momentum conservation, therefore, we get the speed when the pth bead falls off as
follows
We know that i.e. when the first bead just falls off the edge of the table, its speed is
zero. Now we can write
And so on so that continuing in this manner we get ( )
This gives
9.15 From problem 8.18, the total force required to move the chain is . Thus the
power delivered by the person pulling the chain is =
On the other hand, the energy of the chain is = kinetic energy + potential energy
If the length of the chain on the table is x then and
Kinetic energy = potential energy =
Thus Total energy E =
This gives
Thus the rate of change of the energy of the chain is not equal to the power delivered. As
shown in the previous problem, the energy is lost in the inelastic collision.
One may ask a question: what if instead of the chain, it s a rope or a strin that is being
pulled? Where does the energy go in that case? The answer is that the energy difference is
then used in stretching the rope to generate the required force.
145
9.16Let the length of the chain be L. If its length y is hanging from the table, the force
pulling it down is =
Taking the vertically down direction to be positive, the coordinate of the end of the hanging
portion of the chain, when its length is y , is also y.
Thus the equation of motion of the chain is
The equation can also be derived by considering the two protions, the one hanging from the
table and the other on the table, separately.
Writing we get from the equation above
This gives
The second term in the equation above is the change in the potential energy of the chain as
the length of its hanging portion changes from y1 to y. Thus the total energy of the chain
remains unchanged as it slips off or the energy is conserved. This can also be seen as
follows
When length y1 is hanging,
kinetic energy = 0 potential energy = Total energy =
When length y is hanging,
kinetic energy = potential energy =
Total energy =
It is clear from the above that the total energy remains unchanged.
9.17As the chain unfolds, the mass of the hanging (and moving) portion keeps on
changing. Thus the problem is like the variable mass problem. We take the mass per
146
unit length of the chain to be λ. Taking the vertically down direction to be positive,
the coordinate of the end of the hanging portion of the chain, when its length is y , is
also y. The external force on the chain is , , and the relative velocity of
the mass that is added to it is . Thus the equation of motion of
the chain is
Using we write this equation as
We now solve this equation for as the sum of the solution of the homogeneous
part and the particular solution to get
Here A is a constant. Using the condition that , we get and
therefore
The same result can be obtained by letting and such that in the solution for
a coiled set of beads in problem 9.14.
Now let us compare the energy of the chain at the beginning o fthe motion and agter it has
slipped so that y of its length is hanging.
At the beginning, when length y1 is hanging,
kinetic energy = 0 potential energy = Total energy =
When length y is hanging,
Kinetic energy =
147
Potential energy =
Total energy =
Thus we see that the energy is lost during the motion. This happens due to the inelastic
collision between the chain links as each new link is pulled by the moving chain (see
problem 9.14).
148
Chapter 10
10.1 (a) The fields are shown on the axses. They are the same all over the place.
(i)
(ii)
(b) If we think of the force arrows as velocity of a fluid, we see that a matchstick thrown in
that fluid will tend to rotate clockwise in (i) and counterclockwise in (ii). Thus the curl of
both the fields is not zero; it is negatve for (i) and positive for (ii).
(c) curlf of force field (i)
Curl of force field (ii)
149
x
y
x
y
10.2
(i) Force field .
Path 1: Work done is zero as the particle moves along the x-axis. Similarly as it moves from
(2,0) to (2,1), work done is again zero since the particle is moving perpendicular to the force
field. Thus alongh path 1, the net work is zero.
Path 2: Work done is zero as the particle moves along the y axis. However, as it moves from
(0,1) to (2,1), it is under a constant force of 1 unit in the x direction. So the work done by the
field is 2 units.
Path 3: Along path 3 . Thus . The displacement along path 3 is given as
. Thus
unit
(ii) Force field
Path 1: Work done is zero as the particle moves along the x-axis since the particle is moving
perpendicular to the force field. Similarly as it moves from (2,0) to (2,1), Field is constant and
equal to 2 units. Thus the work done by the field will be 2 units. Thus alongh path 2, the net
work is 2 units.
Path 2: Work done is zero as the particle moves along the y axis because the field is zero. As it
moves from (0,1) to (2,1), it is is moving perpendicular to the force field so the work done is zero
again. So the net work done by the field is zero.
O X
Y
(2, 1)
150
Path 3: Along path 3 . Thus . The displacement along path 3 is given as
. Thus
unit
In both the cases the work done depends on the path. It is therefore consistent with the curl of
both the fields not being zero.
10.3 Force field is . The paths are shown below
We will calculate the work done along path 1 in two parts: first when the particle mones
along the x-axis and secondly when it is moving from (1,0) to (1,1). Along the x-axis, the
force is and the displacement is . Thus the work done is zero when the particle
moves along the x-axis. When the particle moves from (1,0) to (1,1), the force is
and displacement is . Thus the total work done is
This then is the total work done along path 1.
Along path 2 y = x so that dy = dx. The work done is given by the integral
Since the work done along two paths is different, the force field is NOT conservative.
10.4 The figure for the path si shown below. The way we have set up the transformations
Path2
O X
Y (1, 1)
path1
151
, the corresponding angle is as shown in the figure and
varies from π to 2π. Thus the integral from A to B over the
semicircular path is
The integral can be carried out easily and gives
10.5 . The force field will be conservative if its curl vanishes. The curls
of it is
If the curl has to vanish, we should have .
For the force field it is clear by inspection that the potential should be
. However, to derive it formally we put
This gives
Y
X
C
BA
(0,1)
(2,1)
152
Which is integrated to
Differentiating this with respect to y and writing gives
By the condition , the const. is zero. Thus
10.6 (i) Curl of the field
is not zero. Therefore the field is not conservative.
(ii) The curl of the field
is not zero. Therefore the field is not conservative.
10.7 (i) The function will be a constant where its
argument is a constant. Thus the contours are given by
These are concentric circles with centre at .
(ii) The gradient of the function is given by
10.8 Kinetic energy of the system of N particles with masses and positions
is
153
Let the position of the CM be so that . If the positions and velocities of these
particles with respect to the CM are given respectively by and then
and
Substituting this in the equation for kinetic energy above, we get
Denoting the total mass as and using the property of the CM that , we
get
This is the desired result.
10.9 When some energy is released during collision, the equations during the collision are
(momentum conservation)
(energy conservation)
Here the unprimed quatities are before collision and the primed quantities are after collision.
Further . The easiest way to prove that in the bove situation, the paricles cannot move
stuck together is to write all quatities in the with respect to the CM. In that case (referring to
quantities in the CM frame with subscript c)
And using the splitting of the kinetic energy as in the problem above and the fact that
Now if the particles are moving together, their momenta after the collision with respect to the
CM will be zero. This is also seen mathematically as follows. By momentum conservation
154
And if they are moving together, then
The above two equation give
Putting this in the energy conservation equation gives
However that is not possible because two positive quantities cannot add up to zero. Thus the
particles cannot move stuck together.
10.10 The picture of the carom coin and the striker is shown below
The coin will move in the direction of the impulse that it receives from the striker. This
direction is perpendicular to their common surfaces and theefore along the line joining their
centres. Thus the coin moves at an angle such that
We will work in cgs units. Initial momentum of the system is that equal to the initial
momentum of the striker which is .
Y
X
2cm
2ms-1
2.05cm 1.55cm
Direction of impulse on coin
155
If after the coliision, the velocity of the striker is and the speed of the coin is v
then its velocity would be and the momentum
conservation will lead to
Since the collision is elastic, the total energy is conserved and we get
These equations simplify to
These are 3 equations for 3 unknowns so all the answers can be obtained from these
equations. Substituting
In the energy conservation equation gives
This gives after collision. The trivial answer of course refers
to the situation before collision.
This then leads to . This gives the angle of deflection
of the striker to be below the x-axis.
(ii) KE o fthe CM remains unchanged during the collision. It is therefore .
(iii) Velocity of the CM =
Therefore the striker is moving with velocity 0.5 ms1 and the coin with -1.5 ms1 along the x-
axis in the CM frame. The magnitude of momentum of each body is 0.0075 kgms1 in
156
directions opposite to each other (see figure). In the CM frame the magnitude of velicities
does not change during an elastic collision. Thus the momentum and the velocity vectors of
the striker and the coin just rotate. Further, the impulse J is in the direction (see figure) such
that it makes and angle
from the x-axis. As is clear from the figure, the magnitude of J must be such that the final
momentum has the same magnitude as the initial momentum. This is seaily done by drawing
a circle of radius equal to the magnitude of the momentum with its centre at the tail of the
initial momentum vector. We then draw the impulse vector from the head of the initial
momentum vector at the angle and take its length such that its head touches the circle. The
vector from the centre to this point gives the final momentum. The construction
immediately shows that
It is also clear from the figure that
It is also clear from the figure that the angular momenta vector srotate by
33.75
J
0.0075 kgms1
0.0075 kgms1
157
As a check we now calculate the velocities of the striker and the coin in the lab frame from
the information above and compare our answer. As is clear from the figure, the x component
of the striker’s velocity in the CM frame is
This then gives Vxlab as follows (keep in mind that the CM is moving in x direction only)
And we get from the figure (the CM is moving in x direction only)
Thus
Similarly for the coin (see figure)
This gives
and we get from the figure
This gives
These match with the previously obtained answers.
10.11 As in the problem above, the stationary balls will move in the direction of impulse
after the collision. This is going to be along the line joining the centre of the striking ball
and the centres of the stationary balls. At the time of colliding, the three balls will look as
shown below.
158
Since the net impulse (due to the two stationary ball) will be along the line of its initial
motion by symmetry (see figure), it will continue to move along its original direction. This is
also seen by noticing that the statinary balls have a net momentum in the direction of v0.
Thus there will be no component of the momentum to be balanced in the direction
perpendicular to that. Thus the striking ball will continue to move along its original
direction. Let the speed of the striking call be v1 after the collision and the speeds (equal by
symmetry) of the other balls be v. Then by momentum conservation
Since the collision is elastic, we have by energy conservation
There are two unknowns v1 and v and two equations so we can get their values. Squaring the
momentum conservation equation and subtracting it from the energy conservation equation
gives
One of its solutions is the trivial solution referring to the situation before collision.
Theother solution is
Substituting this in the the momentum conservation equation gives
30
Direction of impulse on ball
Direction of impulse on ball
159
Chapter 11
11.1 Disc rotating about a point on its periphery. Consider first a rotation about a point on
the periphery by an angle. This is shown on the left in the figure below. The dashed
circle shows the initial position of the disc while the solid circle shows the position
after rotation.
On the right we show the same rotation carried out by translating the CM of the disc first to
its new position, as shown by the straight arrow and then carrying out the rotation about the
CM. We have made the disc in this position by dotted circle. As is evident from the figure,
the magnitude and the sense of rotation is the same as in the figure on the left.
11.2 Now we generalize the result of the problem above. On the right in the figure below,
we show the same rotation as in the figure on the left carried out by translating the opposite
end of the diameter of the disc first to its new position, as shown by the straight arrow and
then carrying out the rotation about the this point. We have made the disc in this
intermediate position by dotted circle. As is evident from the figure, the magnitude and the
sense of rotation is the same as in the figure on the left. Similarly, it can be shown about any
other point.
160
11.3 The angular momentum about the origin is given by . Thus the answers in
different cases are
(i) (ii) (iii)
(iv)
11.4 The position of the wheel and the stone stuck to its periphery is shown in the figure
below.
Vt
t
X
Y
x(t)
y(t)
161
Thus we have for the position , velocity (obtained by differentiating with
respect to time once) and acceleration (obtained by differentiating with respect to
time twice) of the stone
As is evident, the acceleration is towards the centre of the wheel. It is the centripetal
acceleration. The force for this is provided by the force that keeps the stone stuck to the
wheel. This force is
The angular momentum of the stone with respect to the origin is
This gives
The angular momentum changes due to the torque provided by the force that keeps the stone
stuck to the wheel and is equal to the centripetal force. Thus the torque
Thus it is equal to the rate of change of the angular momentum.
11.5 We assume that at time t = 0, the paricle is on the x axis. Thus after time t, its position
vector is give as (see figure)
162
Thus its velocity and acceleration are (obtained by differentiating with respect to time
once for the velocity and twice for the acceleration)
As expected, the acceleration is the centriprtal acceleration. It is provided by the external
force towards the centre. The angular momentum of particle with respect to the origin is
Its time derivative is
The torque due to the external force is
This is the same as the rate of change of angular momentum.
11.6 The angular momentum for a collection of particles about an origin O is
Now let is choose a different origin O’ such that the position vector of O’ from O is (see
figure) so that
and
X
Y
R
Ot
163
Substituting the expressions above in the formula for , we get
where we have used the fact that .
Now the angular momentum about O’ is
Thus if the total momentum of the system is zero, then
and
11.7 At the maximum distance Rmax and the minimum distance Rmin from the sun, the
velocity vector is perpendicular to the radius vector. If the speed of the earth at these
distances is Vmax and Vmin, respectively, then the angular momentum of the earth at
these two points is MearthRmaxVmax and MearthRminVmin , respectively. By the conservation
of angular momrntum we have
MearthRmaxVmax = MearthRminVmin
This gives
O
O’
X
X’Y
Y’
ZZ’
164
11.8 Initial momentum , the final mpmentum and the change in the momentum
are shown in the figure below.
As is evident from the figure, the magnitude of is where and it is
in the direction bisecting the angle between the incident and the scattered direction.
Mathematically it can be seen as follows. Choose the direction of incoming particle to be the
x direction. Then
and
Thus the magnitude of is and it is in the direction .
(ii) Since the paticle is moving parallel to the x axis at a distance d, its angular momentum is
mvd going into the plane of the paper. This can be seen as follows. The position and
velocity vectors of the particle are
and
This gives for the angular momentum
Further, since the force is central, the angular momentum about the origin is a constant.
X
Y
165
(iv) Since , we have . Therefore is in the same direction as
.
To calculate , we change the integration over time to integration over the angle by
using the angular momentum conservation. Using polar coordinates, we write the angular
momentum of a particle moving in the xy plane as . Since in the present
problem, it is a constant equal to , we have
The force between the two charges is in the radial direction and is equal to
Thus
Thus the magnitude of is . Comparison of this expression with that for
the momentum change shows that the two are in the same direction and
Or
This is the Rutherford formula.
166
11.9 (i) At angle the potential energy of the girl is with
respect to the equilibrium point, i.e. when the swing is in the vertical position. The
kinetic energy of the system at the lowest point , if the angular speed is , is
. By energy conservation
(ii) Whe the child stands up at the lowest point, all the external forces on the her are
passing through the pivot so her angular momentum remains unchanged. However
as she stands up her moment of inertia about the pivot is where ICM
is her moment ofinertia about her CM. Neglecting it gives the moment of inertia to
be . Then by conservation of angular momentum
keeping only linear terms in since d<<L.
(iii) The final kinetic energy of the girl is
keeping only linear terms in since d<<L. Thus we see that the kinetic energy of the
system has increased in comparison with the original energy. Threfore the swing would go
higher on the other side.
(iv) Suppose the swing goes up to angle on the othwr side, we have by energy
conservation and the fact that
167
Now we have the approximation d<<L, which gives
keeping only linear terms in . Thus
This gives the increase in the angle of swing in half a period. While going back, the new
amplitude by the time the swing reached its starting point will be.
In the full period, the net increase in the amplitude will therefore be
168
Chapter 12
12.1 Moment of inertia of a ring. Let the mass of the ring be m and its radius R. Since all
the points on the radius are at the same distance from the axis, each small mass on the
periphery gives the same contribution to the moment of inertia. Thus the total
moment of inertia is
A disc can be thought of made of many rings of width at different radii (see figure).
The moment of inertia of each ring is . Thus
the total moment of inertia is
For the moment of inertia about the diameter of a ring, consider a small portion of it of
extent at and angle It moment of inertia about the diameter is .
Thus the total moment of inertia is
12.2 Moment of inertia of a rectangular sheet. The sheet is shown in the figure below
169
We first calculate its moment of inertia about the x axis. For this, let us take a thin strip of
width dy parallel to the x axis and at a distance y from it. Its mass is .
Since the perpendicular distance of all its points is y from the x-axis, its moment of inertia
about the x axis is . Thus the total moment of inertia about the x-axis is
Similarly by taking a thin strip parallel to the y axis, we will get the moment of inertia Iy
about the y axis to be
Let us now calculate the moment of inertia about the z axis. Consider again the strip
parallel to the x axis. By parallel axis theorm the moment of inertia of this strip about the
z axis is = (moment of inertia of its CM with respect to the z-axis + its moment of inrtia
about the axis passing through its CM and parallel to the z-axis)
which upon integration leads to
Z
Y
b
a
X
y
170
12.3 The disc and a strip on it perpendicular to the axis of rotation (y-axis) is shown in the
figure below. The strip is of width dy and at a distance y fron the centre.
Length of this strip is and its mass is . Thus its moment of inertia
about the y-axis is
The integration is easily carried out by substituting and gives the resuly
12.4 This problem can be done exactly in the same manner as above. We now divide the
shell inti thinn rings at an angle (see figure).
X
Y
yR
171
The radius of the ring is and therefore its mass is and
its moment of inertia about the rotation axis is
Thus the total moment of inertia is
12.5 In this problem, we divide the sphere into thin discs and add the moments of inertia of all
discs. Thus for a disc of thickness dy at height y (see figure), its radius is , its
mass is
.
Therefore, the moment of inertia of the disc is
.
Integrating it from R to R gives the total moment of inertia
X
Y
yR
172
12.6 For the moment of inertia about the y-axis, the problem is done exactly in the same
way as in 12.5 by taking a disc at height y. The only difference is that the mass M is
now distributed over half the volume and the y integration runs from 0 to R. Thus the
mass of the disc is
And its moment of inertia is
Thus the total moment of inertia is given as
Similarly, to calculate the moment of inertia about the x axis, we make a cylindrical shell as we
did in example 12.3 (see figure)
Thus the moment of inertia will be calculated exactly like in example 12.3. The mass of this
shell is given by
Y
R y
X
173
Th factor of comes because there is only half the shell in a hemisphere. Therefore the moment
of inertia of the hemisphere is
12.7 A conical shell is shown below. To calculate the moment of inertia, we take a ring at a
distance x from the base extending from x to x+dx. Then by similarity fo triangles, its
radius is . Similarly the length of its side is
Thus the mass of the ring is . Its moment of
inertia therefore is
The moment of inertia of the shell is then given by integrating the expression above over x from
0 to h and gives
Now we calculate the moment of inertia about the y-axis. To do this we use the parallel axis
theorem and write the moment of inertia of the ring considered above as that of its CM plus its
moment of inertia about the axis parallel to the y axis and passing through the CM. Thus
X
Y
h
r
x
174
Integrating this we get
We now do the calculations for a solid cone. The calculations proceed in exactly the same
manner as for the shell bu now instead of a ring, we take a disc at distance x. The mass of the
disc is . Thus its moment of inertia is
Thus the total moment of inertia is
For the moment of inertia about the y axis, we again consider the same disc and use the parallel
axis theorem to write the moment of inertia of the ring considered above as that of its CM plus
its moment of inertia about theaxis parallel to the y axis and passing through the CM. So
Now the integration over x from 0 to h gives
12.8 (i) The total angular momentum = angular momrntum of large disc + angular momentum
of small disc
I2 is calculated using the parallel axis theorem and its value is
Thus
(ii) Let the large disc start rotating with angular speed in the opoosite direction.
Then by conservation of angular momentum
175
(iii) For and , we have
This keeps the total angular momentum zero since the large disc rotates in the opposite
direction with exactly the same angular speed as given to the small disc.
(iv) In a helicopter also, as the large rotor starts, the body of the helicopter will tend to
rotate in the opposite direction. To prevent this, a tail rotor is fitted that provides
the counterbalancing torque.
12.9 The position of the person (represented by the filled circle) after time t is shown on
the platform in the figure below.
As the person moves on the platform, the platform starts rotating clockwise with angular
speed so that the total angula momentum remains zero. As the platform rotates, the
person also moves with it. The net velocity of the person with respect to the ground is
equal to (velocity of the person with respect to the platform + rotational velocity of
the person due to the rotation of the platform). This is expressed as
Thus the angular momentum of the person is
u
A
B
utO
176
Here is the position vector of the person from the origin O on the axis. The position,
various distances and the velocities, as seen from the top, are shown in the figure below.
It is clear from the figure that
Here the sign takes care of the ddirection of angular momentum along the aixs of rotation;
it is positive for counterclockwise rotation and negative for clockwise rotation. Thus the
angular momentum of the perso is
The angular momentum of the platform is
Now equation the total angular momentum to zero (by conservation of angular momentum)
gives
O
A
B
ut
177
This gives
Total time that the person takes to move from A to B is
Thus the angle through which the platform rotates by the time the person reaches B is
This integration can be done by substituting
So we get
Now substitute which gives to get
where . This gives
178
If m = 0, we have and . Thus although on the platform, the person has moved
from A to B but overall he remains at his original position since the platform has rotated
back by .
For , we have
Thus , where 1 . We can therefore write
Thus
This gives
12.10 This is similar to the variable mass problem except that in this
problem we will get the answer by applying the principle of conservation of angular
momentum because this is an extended body and if we try to apply Newton’s second
law to each point particle, it is impossible to solve the problem because of a large
number of internal forces involved.
Let a small mass come out at a given time t during the time interval from t to
t+t from one of the containers. Let the angular speed of the display be at t. Then
the speed of gases coming out with respect to the ground is , as shown in the
figure
179
If in time the angular speed of the display becomes , then by conservation of
angular momentum
Here factor of 4 comes because of 4 containers. Here is the mass of each container at
time t. Obviously . Neglecting the second order term , we get
Thus
This equation can not yet be integrated because should be written in terms of for
that. Obviously . This gives
Integrating this gives, starting from = 0 at t = 0
Thus after the entire gubpowder is exhausted, we have
u-l
u-l
180
12.11 This problem is exactly the same as the problem above except
that the moment of inertia of the display is different because of different positioning
of the containers of gunpowder. Conservation of angular momentum now gives
Neglecting second-order terms and simplifying leads to
Following the steps in the solution of problem 12.10, this leads to
and
12.12 As the water comes out of the sprinkler pipes, it carries angular momentum with it. If
the opposing torque were not there, the system will rotate in the opposite direction with
increasing angular speed to conserve the angular momentum. However it does not happen
because of the opposing torque which is the external torque on the system. Taking the
direction of rotation of the rods to be positive, we have
Here external torque is with the minus sign indicating that it is in the direction opposite
to the rotation. Since the mass of the rod remains unchanged, if the mass of water coming
out from each end in time interval is , we have
and
Thus we have
181
This gives
Since the area of each hole is S, we have , where is the density of water. In
steady state, the sprinker system rotates with constant angular speed so that .
Substituting and in the equation above gives
Assuming that at the beginning of turning the spinker on, all pipes are filled, we also solve
how the angular speed changes with time until it approaches the above vaue. The
differential equation for can be written as
This equation has the solution
Since , we get
This gives
12.13 Let the angle between the unit vector and vector be (see
figure).
182
It is clear from the figure that the magnitude of is and it is in the direction of
. Since the magnitude of is also , we get .
12.14 As the disc hits the rough surface, let the surface apply an
impulse J on it (see figure).
As a consequence the disc moves with a smaller velocity and also starts rotating because
the impule applies a torque on it about its CM. By rolling condition we have .
By the equation for the CM, we get
And by the torque equation
This gives
r
n
rO
JV
V1
183
12.15 Free body diagram of the disc is given below.
Here f is the frictional force on the disc. By the equation for the motion of its CM we get
Taking torque about the CM of the disc we get
For pure rolling we have . Substituting this in the above two equations we get
12.16 (i) Free body diagram of the cylinder is shown below.
Here Jf is the frictional impuse on the disc. By the equation for the motion of its CM we
get
Similarly the angular momentum equation about the CM gives
Where the second equality follows from the rolling condition . Solving the above
two equations leads to
fF
Jf
Jd
184
(ii) For a sphere the equations are the same as for a cylinder except that its I about the
CM is different. Thus the equations become
Their solution gives
.
12.17 The rod in example 12.11 bounces back with angular speed
and speed V. Before it impacts the ground, its angular momentum about the point of
impact is equal to the angular momentum of its CM because it is not rotating, and it is
pointing into the page (see figure).
Thus
After the impact, the rotation about CM gives angular momentum coming out of the page
and the translational motion gives angular momentum going into the page. Thus
h
V
l/2
185
By conservation of angular momentum, we have
By energy conservation we have
These are two equations for two unknowns. Substituing from the
first equation into the second equation, we get the equation
This is a quadratic equation in V, and its solution is
The plus sighn in front of 1 above gives the trivial solution that the velocity of the rod
before impact is downward. And after the impact its velocity is gives by the second
root which is
From , this gives
It is evident from the equations above, for , the rod rebounds without any rotation.
12.18 This problem is similar to the problem 12.17 . However, the
CM and the moment of inertia about the CM are different in this problem. In this
case the CM is at distance from mass m. Thus the moment of inertia about
the CM
Like the previous problem, before the system impacts the ground, its angular momentum
about the point of impact is equal to the angular momentum of its CM because it is not
rotating, and it is pointing into the page. Its value is
186
Let the system bounce back with angular speed and speed V after the impact. Then
Thus angular momentum conservation about the point of impact gives
Similarly energy conservation gives
Again we substitute in the second equation to get
Its solution gives one trivial solution and for speed after impact
and
12.19 The figure below shows the rod and the stone just before the
impact.
187
(i) Right after the impact the angular momentum about the pivot is conserved. Thus,
if the rod and stone stuch with it move with angular speed after the impct, we
have (moment of inertia of the rod and the stone together is )
With , we get
(ii) The kinetic energy of the rod and the stone system after the impact is
If the rod rises by an angle , the potential energy of the system at this point is
Equating the KE and PE, we get
(iii) The impulse by the pivot. As soon as the stone hits the rod and gets stuck with it,
the horizontal momentum of the system changes. This change is brought about by
l43l
188
the impulse that the pivot applies on the rod. Thus by calculating the change in the
momentum of the system, we obtain the impulse that the pivot applies on the rod.
Initial momentum of the system =
Final momentum of the system =
Thus after the stone gets stuck, the momentum of the system changes by
in the same direction that the stone was moving initially. Thus the impulse given by the
pivot is
in the same direction that the stone was moving initially.
It is also instructive to solve this problem by angular momentum consideration by
calculating the change in the angular momentum of the system and attributing it to the
torque provided by the impulse. For this we apply the equation
Here CM is the centre of mass of the entire system (rod+sone). Note that this equation can
be applied only about the CM of the system and NOT about the CM of the rod alone.
Distance of the CM from the pivot point =
Thus the CM of the rod is above the system CM. Similarly the stone is
below the system CM. The velocity of the CM is in the same
189
directon as the stone. Thus befor the stone strikes the rod, it is moving with respect to the
system CM with speed in the same direction and the CM of the rod is moving with
speeed (in the opposite direction). This is shown in the figure below in the system
CM frame.
Thus the angular momentum of the system in its CM before the impact is
where we have used the fact that . The sense of rotation is counter clockwise.
Immediately after the stone hits the rod, rod starts moving with speed
With respect to the CM of the system, the CM of the rod and the stone are moving with
speed (keep in mind that is the same about any point and we are thinking of the motion
of the system as the translation of the system CM plus rotation about the system CM. Thus
with respect to the system CM, the motion is roational)
and
190
Thus the angulat momentum of the system about the system CM after the impact
where we have used the fact that . The sense of rotation is counter clockwise. Thus
the impuse gives a torque equal to
The negative sign here shows that the change is in clockwise direction. Its magnitude is the
torque impulse which is equal to the impulse J provided by the pivot times the distance fo
the pivot from the system CM. For clockwise sense, J is in the same direction as the
firction of stone’s velocity. Thus
12.20 Let the distance of the sweet spot be ls. The ball hitting the bat and its swing is
shown in the figure below.
ls
0
F
191
The point where the bat is held is the pivot point of the bat. Further, let the ball come
horizontally with speed vi and retun alonh the same line with speed vf. Considering
clockwise rotation to be represented by the positive direction, we have:
Initial angular momentum
Final angular momentum
Since there is no external torque about the pivot, we have
or
Finally the momentum change of the system is caused by the force applied on the bat.
Initial momentum is the sum of the momentum of the bat and that of the ball. The final
momentum is that of the ball only. This gives
Since for the sweet spot force is zero, we have
This combined with the equation gives
(i) For M=2 kg, LC=40 cm and I=0.3kgm2, we get
(ii) From the momentum equation above, we get
(iii) With the wrapping of the tape, the mass the moment of inertia of the bat and its CM
all change. We have
and
This gives
192
Thus the sweet spot is lowered by 1.1 cm.
12.21 The problem is solved as example 15.2 in chapter 15.
12.22 For generality we first take the masses on the dumbel to be of
mass M each and the mass striking to have mass m. Since there are no external
forces or torques acting on the system, its momentum and angular momentum
remains the same before and after the collision. For convenience we take angular
momentum about the origin. We show various distances in the figure below.
The momentum components of the mass m are as follows
Initial angular momentum about the origin arises only from the motion of mass m. When
particle is on the x axis, only the y component of its momentum gives the angular momentum
about the origin and it is
clockwise
After the mass m gets stuck with M after hitting it, the CM of the system is at
al/2
M
l/2
Ov
M
mX
Y
193
immediately after the impact.
By momentum conservation the momentum of the system after the imact is the same as before it.
Thus the angular momentum of the CM of the system after the impact is (see figure below)
Since angular momentum is conserved, the rest of the angular momentum comes from the
angular momentum about the CM of the system. Thus the angular momentum about the CM is
This then gives the rate of rotation through the equation
For this we first calculate . It is
Thus
With these we easily calculate the velocity of mass (M+m) and mass M right after the impact.
These will be given by adding the velocity of the CM to their velocity due to rotation about the
CM. Thus
Y
px
M
O
yCM
M
(M+m)
X
py
194
For these answers become
Angular momentum of the system CM about the origin after the impact =
Angular momentum of the system about its CM
and
Chapter 13
13.1 (i)
Thus
(ii) To find the principal axes, one rotates the frame with respect to the z-axis by an
angle so that the coordinates for each particle transform by the formulae
and the resulting coordinates make . Numbering the masses as shown in the figure,
we get
195
Substituting these in the formula for and equating the resulting expression to zero
gives
Substitution of new (x’, y’) also gives
and
13.2 The principal axes (1,2) of the rectangle passing through its CM are shown in the
figure when it is in the plane of the paper. Axis (3) is coming out of the paper.
Y
w
lX
1 2
34X’
Y’
196
(i) Components of the angular velocity are
(ii) Components of angular momentum along the principal axes are
Thus if the unit vectors along the principal axes are denoted as and then
(iii) Kinetic energy of the rectangle
13.3 The system and its principal axes (1,2) are shown in the figure below. Principal axis
(3) is coming out of the paper.
a a
b
12
197
We have
Rate of change of angular momrntum can be found easily by either the Euler’s equations or
by taking components of angular momentum in directions parallel to and perpendicular to
the direction of .
By Euler’s equations: Since the components of in the direction of the principal axes
remain unchanged, we have for the change in angular momentum
With the components calculated above, we get
Thus the vector is always in the direction opposite to that of principal axis . Thus at
the instant shown, it is pointing into the paper.
1
2
a
b
L
198
By taking components of angular momentum in directions parallel to and
perpendicular to the direction of : If we decompose the angular momentum
components L|| in the direction parallel to and L perpendicular to , then as the body
rotates, L|| remains unchanged and L rotates with angulae speed and changes at the rate
and that gives the rate of change of angular momentum. From the figure above, it is
clea that
This is also shown in the figure above. It is then clear that at the instant shown this vector
is going to rotate into the plane of the paper. Thus the direction of change of angular
momentum is into the paper and its magnitude is
13.4 The picture of the system of eight particles is shown below. We also show the
diagonal about which we consider it rotating.
(i) To show that the coordinate system chosen is is also the principal axes system,
it is sufficient to show that all the off diagonal elements of its moment of inertia
tensor vanish. This is easily shown. We do it for Ixy here.
X
Y
Z
199
Thus the set of axes chosen is the principal set of axes.
(ii) For the diagonal shown, the unit vector is =
Thus the angular velocity is given as
To calculate the angular momentum, we also need the moment of inertia about the principal
axes. These are
Thus we have
The kinetic energy
13.5 As the rod rotates, its angular momentum also changes. The required torque is
provided by the gravitational force pulling it down. Thus the rod can be in
equilibrium at two positions. Absolutely vertical or at an angle from the vertical.
The first solution is trivial. For the second solution, we find by equating the
angular momentum change about the pivot (a staionary point) to the torque. Later
we will check the answer by applying the torque equation about the centre of mass
also.
The rotating rod in the plane of the paper is shown in the figure along with its principal
axes at the pivot; axis (3) is coming out of the plane fop the paper. Also shown is the free
200
body diagram of the rod. The pivot applies a vertical force N to balance the weight mg of
the rod and a horizontal force F to provide the required centripetal accelerartion to the CM
of the rod.
The moment of inertia of the rod about the principal axes at the pivot are
The angular velocity components are
Thus the angular momentum components are
Since the angular velocity and its components along the principal axes are constant, we have for
the torque
Thus
Here the negative sign shows that the torque is pointing into the paper. This is proided by the
weight of the rod. The torque of the weight about the pivot is pointing into the paper and its
magnitude is
1
2 N
F
mg
201
Thus we should have
The same answer can also be obtained by taling horizontal (perpendicular to ) LH and
vertical (parallel to ) LV components of the angular momentum and then calculating the
rate of change of angular momentum as LH.
Now we calculate F. This provideds the centripetal force so we have
Check: To check our answers, we apply the torque equation about the CM and see if the forces
calculated by us satisfy this. About the CM we have
Further, for the principal axes at the CM (parallel to those at the pivot)
So that (angular velocity components are the same)
Thus we have, with
Let us see if , N and F calculated by us give the same torque. This is in the direction
perpendicular to the paper and its magnitude is
Substituting we get the torque as
202
Thus our answers also satisfy the torque equation about the CM and are therefore correct.
13.6 (i) Since the wheel is rolling without slipping, it rotates about the horizontal axis
with an angular speed
Further, it rotates about the vertical axis with an angular speed . This can also be
seen easily as follows. Since the wheel rotates a full radians in time , its angular
speed about the vertical is in counterclockwise direction looking at it
from the top.
(ii) Angular momentum about O = angular momentum of the CM + angular momentum about
the CM
Angular momentum of the CM about O = MLV in the vertically up direction
Angular momentum about the CM has both the horizontal and the vertical components.
Angular momentum about the CM = in the vertically up direction + in
the horizontal direction pointing towards O.
Thus total angular momentum about O is
Horizontal component LH = in the horizontal direction pointing towards O.
Vertical components LV= in the vertically up direction.
(iii) As the wheel rotates, the vertical component of the angular momentum remains
unchanged while the horizontal component rotates. Its rate of change is
therefoe equal to
If seen from the top, its direction is as shown in the figure below
203
(iv) The free body diagram of the wheel, when it is going into the page is shown below.
As the wheel rotates, the change in the angular momentum is such that at the position
shown above, it will point out of the paper. On the other hand, torque due to the weight
about O is pointing into the paper. Thus to generate torque coming out of the paper, the
normal reaction of the ground has to be more than the weight of the wheel so that
By balancing the vertical forces, we get
Thus when the wheel is moving, it is pulled down by the vertical shaft at the centre. In
turn, the shaft is pulled up. Thus with time it will tend to come out of the ground.
The horizontal force applied by the shaft provided the centripetal acceleration. Thus
OLH
LH
mgO
N
N1
LF
204
The explanation for why the wheel presses theground harder has been given above.
Another way to think about it is as follows. If there were no gravity, the horizontal shaft of
the wheel will tend to turn clockwise about a horizontal axis as the wheel moves so that the
change in the torque is zero. In turn the wheel presses the ground and generated enough
torque so that the rate of change of its angular momentum is equal to the torque generated.
13.7 This problem is like the previous problem except for position of the centre of mass
and the moment of inertia of a cone. We again obtain the horizontal component of the
angular momentum of the cone and multiply it with the vertical component of the angular
velocity of the cone to get the rate of change of the angular momentum. The horizontal and
the vertical components of the angular velocity and the free body diagram of the cone are
shown below.
Since the speed of the centre of cone’s base is V and its radius is R, . Similarly
.
The principal axes of the cone at its vertex are its axis and two axes perpendicular to it.
The moment of inertia about the axis of the cone is . Thus the horizontal moment
of inertia is
And its rate of change is
H
V N1
mgN
F
205
Coming out of the plane of the paper at the position of the cone shown. This shoud be
equal to the torque about the pivot. Thus
And
Similarly, the force F provides the centripetal force. Thus
13.8 This is a problem where we take the components of the angular velocity according
to the convenience of applying the rolling condition. So we split the angular velocity so
that it has component about the vertical and about its axis. We then find the
relationship between them by demanding that the speed of all the points on the ground
vanishes so that the cone rolls without slipping.
(i) Now a point at distance x from the vertex (pivot point) on the line touching the ground
moves with speed due to the rotation about the vertical axis through the vertex and
speed (see figure below) in the opposite direction due to rotation about the axis of
the cone.
Thus for rolling we get
Now if the centre of the base moves with speed V, we have
x
206
This also gives
As is clear from the components, the net angular velocity of the cone is parallel to
the line touching the ground an in direction shown in the figure. Thus
(ii) To calculate the angular momentum of the cone, we calculate the angular momenta
along the principal axes shown in the figure below.
From the figure it is clear that
In this case, the angular momentum changes because its vertical component rotates with
angular speed . Thus the rate of change of angular momentum is given by
and it is in the direction of axis 3. Its sign depends on the relation between h and R.
Check: The answer can be checked easily by applying the Euler equations that give
12
207
which is the same answer as obtained above.
13.9 In the figure below, we show the horizontal angular momentum LH of the rotating
disc, its change LH as the platform rotates and its free body diagram.
We have
If the torque applied on the disc is zero, i.e., N1 and N2 are equal, there cannot be any
change in the angular momentum. Hence the disc will tend to rotate clockwise in the
position shown so that N1 will become larger than N2. Finally, N1 and N2 will be such that
the torque is equal to change in the angular momentum. This gives
Solving these two equations gives
13.10: It has been worked out in section 13.5.3 (see figure 13.18). Carry it out further for
each axis step by step.
13.11 We show in the figure below the principal axes for the system
at the pivot point and the forces that act on the vertical rod at the bearings. Principal
mg
N2
N1
LH
LH
208
axis 1 is along the rod and 2 and 3 are perpendicular to the rod with axis 3 coming out
of the plane of the paper at the instant the rod is shown. In the free body diagram of
the rod, we have not shown the vertical forces. The cetre of mass of the system is
also indicated in the figure.
The moment of inertia about the principal axes are as follows
The angular velocity components are
Thus the angular momentum components are
The torque required to keep the rod rotating can be calculated either by Euler’s equations or
by the horizontal component LH of the angular momentum and multiplying it by .
Euler equations give
This is the same answer as obtained through LH as is easily checkd.
N2
d
12
d
LH
N1
209
The torque is provided by the reactions of the bearings. The difference in these reactions
also provides the centripetal force as the CM of then system is moving in a circle of radius
. Thus
Solving these two equations gives
13.12 In the figure below we show the principal axes for all the
three rigid bodies. Axes (1, 2) are in the plane of the paper and axis 3 is coming out of
the the paper in all three cases.
In all the three cases we have
and
Thus we have
(b)
1
2
(c)
1
2
(a)
12
210
Now in case (a)
This gives
In case (b)
. This gives
In case (c)
. This gives
13.13 As the ring rotates, the tension in the string does two three things: it balances the
weight of the ring, it provides the centripetal acceleration and it provides the torque
for the angular momentum change of the ring. The figure below shows the principal
axes of the ring at its CM and the free body diagram of the ring. Axes (1, 2) are in
the plane of the paper while axis 3 is coming out of the paper.
211
mgB
AT
O2
B
A1
The components of the angular velocity are
Therefore components of the angular momentum along the principal axes at the CM are
Thus the change in the angular momentum is times the horizontal component of the
angular momentum =
And it points in the direction of axis (3) i.e. coming out of the page at the instant shown.
Euler equations also give the same answer through
However, at the position shown, the tension and the weight of the ring give no torque about
the CM of the ring. Thus the internal forces will move the ring so that there is an opposing
change in the angular momentum. This ring moves so that its B end moves up. This
implies that the ring moves towards position 1. However, as it moves up, the tension
gets misaligned with the CM and starts giving a torque about it and finally the ring stops at
an angle such that the torque equals the angular momentum change.
Now balancing the forces gives
These equations give
If the ring moves up by an angle , The perpendicular distance of the tension and the CM
is about . This gives a torque
Equating this to the rate of change of angular momentum gives
212
This gives
13.14 Following the notation of example 13.7, we have (using parallel axis theorem for
calculating )
Given
(i) The presseion angular frequency will then be
Seeing the change in the angular momentum for the given sense of rotation, the top will be
coming out of the paper.
(ii) We see that . Therefore for the nutation motion we can write
with
The maximum difference between and 0 is therefore . Substituting all the numbers,
we get
(iii) The frictional force is needed to provide the centripetal force. Thus
13.15 The soulution of the Euler equations governing the motion
is the same as in
example 13.7 but the initial conditions are different. Thus we have
213
Here . Let the initial angular speed given about the vertical be . Then
the initial conditions for the subsequent motion are
These give
Thus we get
If the precession velocity of the top is then
This gives
And
214
Upon integration, the equation for gives
The variation of with time is similar to that shown in figure 13.23.
To get the angle through which the top has precessed, we substitute the value of in the
equation for and integrate it numerically. Finally to see the motion of the tip of the
axis of the top, is plotted against .
215
Chapter 14
14.1 For this spring rad s1
(i) giving
(ii) leading to
(iii)
(iv)
(v)
(vi)
14.2 It is given that . Thus the velocity is and the
acceleration is . This is shown below for different values of .
Displacement curve is the one with smallest amplitude of 5, the velocity curve has
216
intermediate amplitude of 10 and the acceleration curve has the largest amplitude of
20. Notice that phase difference of π and π give identical curves.
217
218
14.3 Equilibrium points of the potential are given by .
For , this gives
The roots of this equation are at x = 2 and x = 1. The second derivative of the potential at
these points is
Thus the potential is minimum at x = 2. The corresponding spring constant is
. This gives .
14.4
Equating the derivative to zero gives x = x0. At this point the second derivative
is positive and therefore at this point the potential is minimum.
(i) The corresponding spring constant .
(ii) To plot the potential and harmonic approximation to it, we have taken C=2, x0=1.0
and two values of a: a=0.4 and a=1.2
a = 0.4 a = 1.2
219
(iii)
(iv) As is clear from the figure, depending on the value of a the potential becomes softer
or harder for larger displacements from x = x0. Thus the frequency will become
smaller and time-period larger for a=1.2 and the frequency will become larger and
time-period smaller for a=0.4.
14.5
Equating the derivative to zero gives . At this point the second derivative
Thus the corresponding spring constant is and the frequency of small oscillations is
14.6 The surface charge density gives a electric field that pulls the
displaced electrons back, i.e. it applies a restoring force. We consider volume V of
the displaced block, the force on it is .
The total mass of the block is = number of electrons in volume V electron mass
220
=
So the equation of motion for the displaced block of electrons is (writing )
This gives the plasma frequency (here n is the number density of electrons)
14.7 In this problem
(i)
(ii) Velocity of platform and person on it is calculated by principle of linear momentum
conservation and gives
(iv) If we take the equilibrium point of (person+platform) as y=0, then the displacement
without the person on the platform is = . Thus this is a problem
with the initial conditions
Representin the motion as , we have
Thus the displacement is given by
14.8 In this case, it is the motion of a rigid body about a pivot point. Thus the equation of
motion is written in terms of the moment of inertia, angular acceleration and the
restoring torque. If the square is displaced by an angle about the vertical (see
figure) the torque is
221
The moment of inertia about the pivot is calculated by the parallel axis theorem and is
The quation of motion is
This can be rewritten as
This gives the frequency of oscillation to be
14.9 These two pendulums with their displacements are shown in the figure below.
a
mg
222
For visualizing the force applied by the spring, let us take . Then the bob on the left
feels a force to the right due to the spring and to the left due to the weight of the bob. The
spring force is in the opposite direction on the pendulum on the right.
(i) Since the rods are rigid, and therefre generate internal forces, we use the angular-
momentum torque equation for describing the motion of the pendulums. Thus the
equations of motion for the two pendulums are
(ii) The equations above are solved by adding them to get the equation for
and for . These are
These give
Combination of these two gives and . There are four unknowns that will be given
in terms of four initial conditions.
M
L
1
K
2
223
14.10 Angular displacement of the rod by and angle and the
corresponding angle that the strings make with the vertical are shown in the figure
below. Also shown are the tensions in the strings; these are equal by symmetry.
Since we are dealing with a rigid rod, the correct equation of motion to be used is the
angular momentum-torque equation. There are three unknowns in the problem: , and
T. We thus need three equations. These are
In the small angle approximation we have
Then
And the equation of motion becomes
Thus the frequency of oscillation is .
14.11 We show in the figure below a displacement of the rod when
the left spring is stretched by y1 and the right one by y2.
l
L
TT
224
The equation of motion for the CM is
with .
And the equation for rotation about the CM is
where we mesure counterclockwise as positive. Then
Thus we have for the CM
And for rotation about the CM
With the initial conditions and the rod held stationary in the beginning,
we have
This then gives the answer
L
y1y2yCM
225
14.12 Since we are writing the displacement as , the projection of the
phasor on the y-axis gives the displacement. The phase angle is measured from the x-axis.
In the following we show the position of he phasor at t = 0. After that it rotates
counterclockwise.
14.13 Assuming that the swing is performing simple harmonic
motion, the period of the swing is
Therefore the speed of the person on the swing as the swing passes through its equilibrium
point is =
(i) When the swing is at the extremes and the child is handed over, the amplitude will
not change. It is like strating a swing, ireespective of its mass, from a distance A
from the equilibrium with zero initial speed. Energetically it can be seen as
follows:
When only the man is on the swing the total energy is =
When the child is handed over to the person at the extreme, the child brings in additional
potential energy (with respect to the equilibrium point)
= Mchildgthe height of the extreme point with respect to the equilibrium point
(i) (ii) (iii)
(iv) (v) (vi)
226
Thus the total energy that the swing posseses after the child is handed over is
If the new amplitude is Anew, this should equal (keep in mind that remains unchanged)
A comparison in the total energies calculated in two ways immediately gives .
(ii) When the child is handed over at the equilibrium point, the speed os the swing decreses
by the conservation of linear momentum. It is
And the total energy of the system is now
If the new amplitude is Anew, then (keep in mind that remains unchanged)
This gives .
(iii) As is clear from the calculations above, energy is conserved in case (i) only.
14.14 The equation of motion now will be
Its general solution is
With the initial conditions , the solution is
Since the velocity of the block is
227
It becomes zero at , At this time
14.15 (i) Since this is the motion of a rigid body pivoted at a point
under an external force, its motion is described by the angular momentum-torque equation.
The torque on the body is applied by the weight acting at its CG, and it is a restoring torque
(see figure). The value of the torque about the pivot point is
The moment of inertia of the rod about the pivot point is
Thus the equation of motion for the rod is
For small angles this equation bocomes
(ii) As the pendulum swings about, the frictional torque causes it to lose energy and
therefore the amplitude of the pendulum decreases slowly. The equation of motion
mg
228
can be written and solved exactly as in the problem above. When the pendulum in
the figure above is moving clockwise, the equation of motion is
With the initial conditions , the solution of the equation above is
(just like in the problem of spring-mass system with friction)
Like in the problem above, this then leads to a reduction in the amplitude by by the
time the pendulum reaches the left extreme. Thus in one cycle the amplitude reduces by
. We will now derive this result from energy considerations also.
Suppose at a certain instant the pendulum starts with the maximum displacement of and
goes to the maximum angle on the other side. Then the total angle covered by it is
and the work done against the frictional torque is therefore . The energy
loss during the motion is . Equating this to the work done against
friction gives
Thus in one cycle the amplitude reduces by .
Now if the pendulum starts with an angle and completes N cycles, it will stop swinging
when it is at angle such that . Thus we have
14.16 As the mass leaks out, it carries with it the energy at the rate
. If at time t, the amplitude is A(t) and the frequency (t), then
229
and the average rate of loss of energy E(t) of the
oscillator is
In time averaging A(t) and (t) come out of the integral because they vary slowly over a
few oscillations (that is precisely why they can be defined). The negative sign shows that
the energy is being lost with time.
And if amplitude is A(t), the energy and the rate of change of energy
. Combining all this gives
If the amplitude at t = 0 is A0, this equation is integrated as
This gives
14.17 The energy loss is given by the formula
Thus the average energy loss is
If the damping factor of the system is , then where the energy E is
. Thus for the current problem we get
230
14.18 We consider an oscillator with initial conditions so that its
motion is given by
For undamped oscillatot the siplacement is maximum when . For the damped
oscillator, it will be given at time when
Since Q is very high, the maximum occurs when where is very small. Since
the maximum occurs before , it is advanced by phase angle . Thus
For small , we have
This gives .
14.19 If the person gives an impulse J, the energy gained by him is
Jv, where v is the speed at the equilibrium point. Since , we have
Energy gained per cycle =
This will equal the energy loss per cycle due to damping.
Energy loss per cycle = 2πenergy loss per radian =
Here E is the energy of the swing. This follows from the definition of the quality factor.
231
Thus we get
Putting in all the numbers gives
14.20 It is given that and the mass of the platform is
50kg. Since the system is critically damped for 500kg put on the platform, we have
So the coefficient of drag force
Thus when a 200kg weight is on the platform, the value of
And the angular frequency
Thus , which makes the system hevily damped.
The solution then is
with
So
Here A and B are to be determined by the initial conditions.
Initial conditions:
Since we are taking the equilibrium position of the (load+platform) as y = 0, the initial
displacement from that position is .
(i) The speed of the load when it lands on the platform is .
Then by momentum conservation, the load+platform will move with the speed
.
232
(ii) From the above, the initial conditions are .
Thus we have from the solution above
Thses give
The solution therefore is
14.21 For a forces oscillation the angle by which the displacement
lags the applied force is given by equations
For a very heavily damped oscillator . Thus we have
This gives
233
Chapter 15
15.1 We perform our calculations in a noninertial frame attached with the box and take the
origin (x = 0) at the point where the spring is connected to the box. In this frame,
there is a pseudo force ma acting in the negative x direction. Thus the system in the
noninertial frame looks as shown below.
The equilibrium point x0 is given by
Thus the equation of motion for the mass in this frame is
At , the initial conditions are
We change the variables to and write the above equation as
with the initial conditions This gives the
soulution
15.2 This problem is very easy to solve in the accelerating frame attached with the car.
The free body diagram of the door in the car frame with pseudo force included is
shown below.
ma x = 0
l
234
In the car frame therefore the door is being pulled at its CM by a force Ma and rotates
about the hinges. Thus the problem becomes like examples 12.7 and 15.3 where a
ruler/rod, pivoted at one of its ends’ rotates about an axis at that point when the pivot point
starts accelerating with an acceleration. Then by energy conservation this gives the answer
for the angular speed of the door when it is about to close
15.3 This problem is similar to problem 12.7 and the problem above and is solved in
exactly the same manner.
15.4 We substitute in
to get
Now from equation 15.8 and so we have
Since , the above equation is
Again substituting from equation 15.8 and ,
we get
car
Ma w
235
which gives
15.5 In the rotating frame the rod is stationary and there is a pseudo force – the centrifugal
force – acting on it. Thus the free-body diagram of the rod in the rotating frame is as
shown below. Notice that we are not taking the centrifugal force to be acting at the centre
of mass because it is different for different portions of the rod; it increases with the distance
of fom the axis.
(i) It is clear from the figure above that the rod is pulled out horizontally by the
centrifugal force (in the rotating frame) and would therefore move out when
displaced from the vertical position. Since we are dealing with a rigid body, we
should be working in terms of totques. Thus at the given position, the centrifugal
force applies a counterclockwise torque on the rod but at the vertical position,
neither its weight nor the force by the pivot apply any torque. Thus the rod will
tend to swing away from the axis. It will be clearer mathematically in part (ii).
(ii) When the rod is at an angle from the vertical, the component of force on a portion
of length ds at distance s from the pivot is (see figure).
Centrifugal force
mg
236
Thus the torque due to the centrifugal force is
At the same time there is an opposing torque due to gravity and its value is
Balancing these two gives
Thus as long as , the rod will be at equilibrium at the angle whose
cosine is given above. Thus when disturbed from the vertical position it will move out to
this equilibrium position (with very small friction damping the motion but not affecting the
equilibrium position). For angular speeds such that , the rod will
not move out because the torque due to the centrifugal force will not be able to overcome
the torque due to the rod’s weight.
15.6 This problem is similar to the problem above except that there
is no gravitational force involved here. If looked at from the top along CD, the free
body diagram of the rod in the rotating frame, when it is at an angle from the frame,
looks as shown below.
mg
s
237
If we take a strip of width ds at a distance s from the axis CD, the mass of the strip will be
and the centrifugal force on it = . The net torque on it is
therefore
This shows that both and are equilibrium positions of the sheet.
(i) Thus when disturbed slightly , the torque on the sheet is
and tends to take it away from that position. The equation of motion for slight
disturbance from the position parallel to the frame is therefore
This gives
Therefore the equilibrium position at is an unstable equilibrium position.
(ii) If we call the angle from the perpendicular position of the sheet then .
The expression for torque in terms of remains
However, as the sheet is disturbed from this position, the torque has restoring nature. For
small therefore the equation of motion is
A Bs
238
Thus the motion about this position is oscillatory and is given by
or equivalently by
Therefore the equilibrium position at is a stable equilibrium position.
15.7 We follow the convention for the directions as in the main
text. There is no force in the horizontal plane. The equations of motion in the northern
hemisphere are therefore
If , vx and vy would remain zero for a particle thrown up. Thus correct to the linear
order in , the equations above are
and
This gives
and
Upon integration, the second equation gives
Straightforward approach to solve for the deflection by the time the particle reaches the earth
again would be to find the time for it to come back to the ground and substitute it in the equation
for x(t). We have
,
Time taken to reach the highest point
239
And the total time of flight = 2T = 9.04s.
Thus the total deflection by the time the stone comes back to the ground is
cm
The negative sing in front indicates that the deflection is towards the west. This is an interesting
result. One’s immediate answer would normally have been that the stone deflects one way while
going up and the other way while coming down, since the sign of vz changes, the net deflection
would have been zero. This does not happen because by the time the stone reaches its highest
point, it already has a westward velocity. To see its effect, let us calculate the distances in two
steps: first when the stone goes up and the second when it comes down.
While going up, the deflection of the particle by the time it reaches the highest point is
At this point it has the horizontal velocity
cm s1
The negative sing in front indicates that the velocity is towards the west. Now, as shown in
example 15.9, if a stone is dropped from a height of 100m, it deflects to the east by cm.
However, now the stone has an initial westward speed of cm s1. Thus the nest
deflection fo th stone while it is coming down will be
This gives a total deflection of during the entire flight.
15.8 The initial components of the velocity in the east, north and vertical direction are
Equations of motion in are
240
Since is very small, we will do our calculations correct to the first order in . This means that
for vx and vy, we substitute their initial values and for vz we substitute in the
equations above. This gives
Integration of the last equation, with proper initial conditions , gives
For time of flight T calculation, we substitute z = 0 and get
Thus the time of flight of the projectile increases. Now we integrate the equation for motion in
the x direction, with the initial conditions to get
Similarly, integration of the equation for the motion in the y direction gives
241
Thus the deflection of the projectile in the east and north direction are known. As a check, we
take a projectile thrown staright up and find that the answer matches with that obtained
in problem 15.7. To know the deflection in the direction of launch and perpendicular
to it, we transform these as (see figure)
This transformation gives
To calculate the range and deflection from the path during the flight, we substitute the time of
flight T for t. To the first order in , we then have
X
Y
X’
Y’
α
O
242
Therefor the range, up to the first order in is
So the change in the range due to the coriolis force is .
The sideways deflection is given by
Thus the sideways deflection is .
This shows that a projectile fired eastward will deflect towards the south and that fired
westward will deflect to the north. If we look at the equations of motion in the
northern and the southern hemisphere, they differ by the sign of the terms containing ,
which is equivalent to changing the sign of λ to λ. From the expression derived above, it is then
clear that the change in the range will not change but the sideways deflection will change to
in the southern hemisphere.
15.9 Exact solution of the equations of motion on the surface of the earth. Thse are
243
To get the exact solutions, we differentiate the first equation once and get
Substituting for the derivatives of the velocity components appearing on the right, we get
The solution of this differential equation is given by the sum of the solution for its homogeneous
part and the particular solution. Thus it is
Here A and B are determined by the initial conditions. Subztituting this solution in the equation
for vy gives
Here C is another constant. Similarly from the last equation we get
Here D is another constant.
No wlet us determine the constants appearing in the equations above for a stone dropped from
height h. Since we have solved a second-order differential equation for vx , we need two initial
condtions for it. These are . Then we have
244
This gives
For the y and the z components of the velocity we have . These give
C = 0 and D = 0. Thus the complete solution for the velocity is
In the limit of this gives, to the first order in ,
This leads to the same answers as in example 15.9.
15.10 Cyclone building up in the Bay of Bengal. If only the motion in the horizontal plane is
considered, the equations of motion are
We choose the coordinate system such that its origin is where the storm starts from. Thus the
initial conditions are . The second
equation above can be immediately integrated to obtain
245
where C is a constant. Since , we get C = 0. Thus
We substitute this in the first equation above to get
This gives
With the initial conditions , this gives
Thus
With the initial conditions we get . Thus finally we have
for the coordinates of the eye of the cyclone
and
(i) This gives the equation for the trajectory as
Since , the above equation can also be written in
kilometers as
246
Thus the trajectory is a circlular one with the centre at km.
(ii) Thus the sense of the trajectory is clockwise as seen from above. On the other hand, since
we are in the northern hemisphere, the winds around the eye move in counterclockwise direction.
(iii) To find out where the cyclone hits the coast, we substitute in the equation above
and get and . The second coordinate is for the return
path. Thus the cyclone hits the coast 18km north of where it started from.
15.11 The solution here is similar to the solution above except for the initial conditions. We
take the origin to be where the striker is played from. The x and the y axes are shown in the
figure below.
For the problem . Thus the equation of motion in the xy plane are
1 2
A
B
x
y
247
Note that the signs on th right hand side are opposite to what they are in the equations of motion
in the orther hemisphere of the earth because the direction of the angular velocity is opposite.
Assuming that the striker is played at an angle from the x axis, the initial conditions are
The second equation above is integrated to give
With the initial condition , we get . Thus
Substituting this in the first equation of motion, we get
The solution for the equation is then obtained as the sum of the solution for the homogeneous
part and the particular solution. Thus
With the initial condition , we get . Thus
When substituted in , this gives
Solved with the initial condition y(0) = 0, this gives
Thus the trajectory is described by the coordinates
These can be combined together to give the equation of trajectory as
248
Thus the trajectory is a circle with centre at and the sence of direction is
therefore counterclockwise. This implies that the striker should be played in direction 2. Now
we want the trajectory to be such that it pass through point B, i.e. through coordinates .
When substituted in the equation for the trajectory, this gives
If the angle with AB is α, then
The striker is played in direction 2 making an angle from AB.
(ii) We first solve this problem for correct to first order in in an easy way. We then
solve the problem exactly.
Easy approximate solution correct to first order in :
It is given that initially and . Thus as we integrate the equations above and
therefore . So up to order , vy can be taken to be a constant equal to v. Thus
and the integration of the first equation above gives
Since , we get C = 0. This gives
because x(t=0)=0.
Therefore by the time the striker reaches the other end, time taken by it is and its has
moved a distance and has x-component of the velocity . Now the
249
striker starts its journey back after hitting then board. It again takes time to reach the side
it started from. Now the initial x-componet of the velocity is and the displacement
. Now if we integrate the equation with these conditions, then
This gives
Keep in mind that t is being measured from T onwatds. Thus t = 0 inplies when the striker starts
its journey back. Integrating this with the initial condition , we get
For this gives
This is the final displacement when the striker comes back. One would have thought that the
striker will come back to its original position; that does not happen because when it starts its
journey back, it has an x-component of velocity that makes it drift. Had the x-component been
zero when it started back, the striker would have reached its original position.
Exact solution:
If the striker is played along line AB then . The trajectory of the striker is then
and with time x(t) and y(t) vary as
Thus for y = L, we have from the trajectory equation
250
Thus the striker gets displaced in x direction as it reached point B. One of the two answers
(smaller magnitude ) is when the particle is moving upward. The other
one (larger magnitude ) is when the striker would have returned had it
not hit the other side of the board. Further, when the striker reaches the other end, it would have
taken time T such that y(T) = L. This gives
The x and y components of the velocity at the other end are therefore
From the above, one sees that the speed remains unchanged during the motion. This is
expected since the coriolis force is perpendicular to the velocity and therefore does no work on
the striker. As the striker hits the opposite side of the carom and returns back, its x velocity
remains unchanged and the y component of the velocity changes direction and it traverses a new
trajectory. Taking the time when it starts back to be t = 0, the new trajectory is thus determined
by the initial conditions
One could solve this problem with these initial conditions. However, we can make use of the
equations already derived for the trajectory if we describe the journey back with new coordinate
system with the origin at the point where the striker starts back. This is shown in the figure
below. In this coordinate system the initial conditions are
So that we have initial speed v at an angle such that
251
Thus the x and y displacement of the striker in the new coordinate system is
These can be combined together to give the equation of trajectory as
For y = L this then gives
While cutting the y = L line for the first time, the value of x will be
This is in addition to the previous displacement of the origin in journey. Thus the total
displacement is
x
y
v
241
2 2
22 vv
Lvx
A
B
252
It is easily seen that for this goes over to the approximate answer obtained earlier.
253
Appendix A
A.1 In this problem there are four variables. So we make one dimensionless variable and equate
it to a constant. The variables of the problem and the corresponding dimensions are
Let the dimensionless variable be . Since this is a dimensionless variable we have,
on equating the dimensions of the right hand side in the equation above to zero
Since we want an expression for p, we take a = 1. Then the equations above give
and . Therefore the dimensionless variable is
Equating it to a constant k, we get
A.2 This problem has three variables. Therefore to apply Buckingham’s π theorem we form one
dimensionless variable and equate it to a constant. The variables of the problem and the
corresponding dimensions are
Let the dimensionless variable be . On equating the dimensions of the right hand
side in the equation above to zero we get
Taking a = 1, since we want an expression for p, we get and . Therefore the
dimensionless variable is
Equating it to a constant k, we get
254
A.3 This problem has four variables. Therefore to apply Buckingham’s π theorem we form one
dimensionless variable and equate it to a constant. The variables of the problem and the
corresponding dimensions are
If the dimensionless variable is , on equating the dimensions of the right hand side
in the equation above to zero we get
Since we want an expression for E, we take a = 1. Then the equations above give
and . Therefore the dimensionless variable is
Equating it to a constant k, we get
A.4 This problem has four variables. Therefore we form one dimensionless variable and equate
it to a constant. The variables of the problem and the corresponding dimensions are
If the dimensionless variable is , on equating the dimensions of the right hand side
in the equation above to zero we get
Since we want an expression for , we take a = 1. Then the equations above give and
. Therefore the dimensionless variable is
Equating it to a constant k, we get
255
A.5 This problem has five variables. Therefore to apply Buckingham’s π theorem we form
twodimensionless variables and write one of them as a function of the other. The variables of the
problem and the corresponding dimensions are
If the dimensionless variables are expressed as , on equating the
dimensions of the right hand side in the equation above to zero we get
These give and . Since we want an expression for , we form one of
the dimensioless variables with a = 1. Then the equations above give and
. Taking d = 0 gives giving one dimensionless variable as
For the other dimensionless variable, we take a = 0. This gives b = c = 0 and . Taking e =
1, the second dimensionaless variable is
Thus the functional relationship between the variables can be expressed as
Now we have several choices for the function f. If we take it to be a constant, we get
But this is not consistent with observations. We next take where k is a constant. Then
we get
This gives answer consistent with observations. For corrections to higher orders, we can take
higher powers of and construct higher order functional relationships.
256