engine tools

17-2

Sprocket Shaft SealInStaller by JImSThis tool presses oil seal over sprocket shaft into case.t4841 69-up Big Twin

Sprocket ShaftbearIng InStallatIon toolUsed to install crank shaft assembly into crank case Timken bearing.t4860 55-up Big Twin Includes Twin Cam 88, aftermarket & S&S motors. repl. oem 97225-55t4879 Replacement bearing & flat washerst3225 Use on all Sportster & K models

hard capUse to protect sproket shaft when using T4869 or a press. t4655 55-present Big Twin Includes Twin Cam 88 aftermarket and S&S motors.

Sprocket Shaft bearIngrace toolUse to remove and install Timken bearing race from motor case.t3222 69-up Big Twin t3223 77-up XL, 87-up Buell

alSo needed:t4835 Handle for bearing race toolst4688 Tool driver spacer

Sprocket Shaft holderUse to hold the flywheel assembly in vise, with or without left case attached. Including aftermarket and S&S motors.t4654 55-present Big Twin

17-3

engine tools

tImken bearIngremoverSUse to remove Timken bearing from sprocket shaft withoutremoving shaft from flywheels.t4874 57-up Sportstert4875 55-up Big Twin

tImken bearIng race InStallerUse to install bearing races in left crankcase & to press in bearing races straight. Also aftermarket & S&S motors.t4683 69-present Big Twin, Twin Cam 88, aftermarket & S&S motors 77-present Sportster & 87-present Buell

bIg twIn Sprocket locker by JImSUse to lock final drive sprocket. For removing and installing sprocket nut.t3670 80-up Big Twin with Belt Drives

tall engIne StandAt a full 1 taller than most stands this powder coated finished stand will fit all Big Twin cases for convenient bench top engine repair.t4832 Big Twin tall engine stand

engIne Stand for XlFits Sportster engines. Top quality steel bench stand simplifies engine overhaul and has a powder coated finish.t4866 57-up XL

engine tools

17-4

head holder toolThis tool is used to hold head in vise by threading directly into spark plug hole. Has 14mm and 12mm ends.t3655 48-up Big Twin 48-Up & 57-up Sportster from JIMSt4440 48-up Big Twin 48-up & 57-up Sportster from Pingel

eXhauSt Stud drIll plateThis tool is designed to keep alignment of drill bit in order to drill out broken exhaust stud, completely. A follow up with a tap is all that is needed to clean up thread hole. This tool can be used with motor in most frames.t4890 84-up Big Twin, 86-up Sportster & 87-up Buell

balancer Shaft alIgnment toolThis tool is a must have for maintaining a long life of your balancers drive chains and bearings. This tool will take all the guess work out of setting up your sprocket and chain alignment.t4685 2000-present Twin Cam B Softail

compreSSIon releaSe valve toolUse this tool for machining all Twin Cam heads 1999 & later, for preparing heads to install JIMS compression release valves. Install on the front or rear head, with or without the valves installed.t4828 All Twin Cam A or B model enginesthread tap toolFor cutting threads in cylinder heads to install compressionrelease valves. Tap size: M10 X 1.0. Use with 9mm .354 pilot.t4833 Big Twin, Sportster, Buell engines

engIne Stand for twIn cam by JImS Fits all Twin Cam engines to present.t4810 Twin Cam 88 A Engine standt4816 Twin Cam 88 B Engine stand

17-5

engine tools

flywheel rebuIldIng JIgEasy R & R of all shafts. Two 7/16 allen set screws hold bottom keyed flywheel. Channel Iron keeps unkeyed top flywheel from moving. Very little truing of flywheels needed. Usually squeezes with C clamp or spreads with chisel. Made by Rowe.t4803 Flywheel Jig complete kit.

caSe lap toolThis tool allows the builder to remove more material in less time with greater accuracy than any conventional lap. Guided on both sides of pinion bearing.t4871 Case lap

balancer Shaft bearIng remover & InStaller This tool will pull the bearings from the B motor case in one easy smooth motion preventing any damage to the bearing bores.t4686 2000-present Twin Cam B Softail

crank dISaSSemblyremovIng toolThis tool can be used to press flywheels from engine cases. It will also press cases apart and break sealant bond. Tool part# T4655 required.t4869 55-up Big Twin Includes Twin Cam 88, aftermarket & S&S motors.

cam caSe borIng tool for twIn cam by JImSThis Twin Cam Alpha & Beta case boring tool takes all the guess work out of boring Twin Cam engine cases to accept Jims 4 bore cylinders, 100 Big Bore kits & 113 & 116 flywheel stroker kits. This tool was designed to be used in a heavy duty 15 drill press or milling machine. Comes complete with instructions.t4907 Cam Case Boring Tool

cam cover holdIng toolHolds cam cover for installing and removing bushings. Holds cover flat and keeps it from being scratched, a must for chrome or polished covers. Single cam motors.t4884 70-up Big Twin

cam buShIng lIne reamerUse this tool to line ream cam cover bushing from inner cam bearing. This will provide a true centerline between the two dimensions.Single cam motors.t4876 70-up Big Twin

cam buShIng InStallatIon drIll JIgUsed to install and drill dowel pin hole in cam bushing to the factory location. Supplied with drill #31. Single cam motors.t4863 70-up Big Twin

cam cover buShIng alIgnment toolUse this tool to check the alignment of cam bearing to cam cover bushing to .0003 of center line. Any binding of this tool indicates misalignment of cam cover or bushing.Single cam motors.t3685 70-up Big Twin

cam cover buShIngremover by JImSUse this tool to remove the cam cover bushing. This sturdy and reliable tool will remove the cam cover bushing in one easy operation. Single cam motors.t3680 36-69 Big Twin

engine tools

17-6

engine tools

17-7

Inner cam bearIng remover toolRemoves the bearing easily without any damage to the crankcase. Also will keep the pin rollers from accidentally falling into the crankcase.t4894 Inner Cam Bearing Remover Twin Cam 88

craneS cam InStallatIon toolThis tool comes complete with instructions to install Cranes adjustable pushrods without removing the gas tank or rocker covers. For FL, FX engines with adjustable pushrods, this tool makes it easy for cam changes without removing pushrods, pushrod covers, tappets or tappet guides. It also has a one year hassle free warranty.e6640 48-up Big Twin

Inner cam bearIng InStallatIon toolThis tool easily installs the inner cam bearing to the proper depth. Single cam motors.t3650 58-Up Big Twin

Inner cam bearIng InStaller toolInstalls the two inner cam needle bearings on Twin Cams. It perfectly aligns to the shaft bores for a precision press fit.t4891 Twin Cam 88

cam bearIng pullerUnlike a general purpose puller, this tool was designed to remove the bearing straight with no slipping or binding.t4898 Twin Cam 88

cam bearIng toolSUse these to install inner cam bearing.With JIMS handle, Win part T4835.t4886 58-up Big Twint4887 57-90 XL

alSo needed:t4835 Handle for bearing tools

engine tools

17-8

cam / crank Sprocket lock toolLock the cam shaft and crankshaft sprockets to properly remove, replace, and torque the sprocket bolts. Made from non marring delrin.t4896 Twin Cam 88

cam chaIn tenSIoner toolThis tool will unload the pressure on the primary and secondary chain tensioners to assemble and disassemble cams. Will also check spring load on chain tensioners.t4895 Twin Cam 88

cam / crank Sprocket lock toolThis tool will unload the pressure on the primary and secondary chain tensioners to assemble and disassemble cams. This tool also chesck spring loads on chain tensioners.t3654 99-06 FL 99-05 FXD 00-06 FXST

twIn cam Inner cam bearIng InStallerUse this tool to press in the two inner cam bearings. This tool has been designed to press from the letter side of the inner cam bearings by putting all the pushing pressure to the very outer wall of the bearing shell. This eliminates any damage to the bearings, cam and cases. This tool will stop at the case and set the bearing depth to .023 to .028 below the case surface. Use with tool T3653 to remove bearings. t3652 06-up Twin Cam Dyna 07-up FL & FXST

Inner cam bearIng remover toolUse this tool to easily remove the inner cam bearing. Insert puller collet into the cam bearing I.D. Insert dowell pin, place remover body over collet, lube threads and with hand tools the bearing is pulled fromthe case. This precision tool will also keep all pin bearings from falling into the engine case.t3653 06-up Twin Cam Dyna 07-up FL & FXST

engine tools

17-9

cam Shaft remover & InStallerWill remove and replace front and rear camshafts and the ball bearings in Twin Cams. It provides precision alignment of the camshaft to ensure a smooth press in and out of the support plate.t4892 Twin Cam 88

bIg twIn cam Seal InStaller and removerNow, for the first time, only from JIMS, you can install and remove a 70-present cam seal without removing the cam cover. t4682 70-present Big Twin single cam only

cam bearIng pullerUse to remove inner cam bearing without splitting cases. Easily pulls bearing from case and also keeps rollers from coming out during removal.t4873 58-up Big Twint4880 57-90 XL

gear Shaft nut Socket wrench by JImSUse to secure pinion gear nut to pinion gear shaft.t4850 55-up Big Twins repl. oem 94555-55a

engine tools

17-10

rod holder toolUse to keep connecting rods in place and eliminate twisting or bending of the connecting rod while reaming or honing the wrist pin busings.t4652 All Big Twins and Buell Blast. Includes Twin Cam 88 A and B.

rod alIgnment toolUse to check rod straightnesswithout removing rods from case.Includes aftermarket and S&S motors .927 wrist pin.t4857 Rod toolt4653 Use on Twin Cam 88 A & B

rod race toolSupports both sides of rod as races are removed or replaced, minimizing the possibility of distortion to female rod or race. Also a new design for installing male rod race. The washer will center the race in the middle of rod.t4865 All Big Twins

rod lappIng SetBesides Big Twins, this tool works for Indian rods. Arbor assemblyincludes 1 1/2 & 1 5/8 laps. t4847 All Big Twins, XL, K, 45 repl. oem 96740-36

tappet oIl fIlter Screw plug toolUse to remove tappet oil fliter screen plug without removing exhaust pipes. t4680 All Big Twin with slotted screw

tappet block alIgnment tool by JImSThis tool ensures that the tappets track on the center line of cam lobe.Single cam motors.t4836 L77-up Big Twin

tappet guIde puller tool by JImSRemoves press fit tappet guides from crankcase.t4842 57-E78 Sportster

17-11

engine tools

pInIon gear InStaller & puller by JImSUse to install pressed on splined pinion gears on Big Twin 39-53. Also to remove pinion gear on Big Twin 39-89 & Sportster 57-76.t4848 Pinion gear tool repl. oem 96830-51

pInIon bearIng pullerUse to remove pinion bushing from cam cover in one simple operation.t4870 54-up Big Twin

pInIon buShIng lIne reamer by JImSUse to line pinion bushing in cam cover from right case race. This is the finest precision line reamer available.t4830 54-up Big Twins & XL idler gear bushing repl. oem 94805-57

pInIon gear lock tool by JImSUse to lock pinion gear, necessary to torque the pinion nut. Tool is simple to use, just align underneath gear and screw into case.t3645 54-up Big Twin

pInIon buShIng InStaller drIll JIgJust press in new bushing with jig and drill through guide hole in jig. Supplied with #31 drill bit.t3203 93-up Big Twint4864 54-29 Big Twin

engine tools

17-12

pISton pIn buShIng tool by JImSUse to remove and install wrist pin bushings without removing rods from crankcase.t4844 Twin Cam 88 repl. oem 95970-32c

wrISt pIn remover & InStallerCut the time it takes to remove wrist pins. easily used by one person.t4888 Twin Cam 88

connectIng rod buShIng toolUse to remove and replace wrist pin bushings in Twin Cams without removing connecting rod from crankcase.t4897 Twin Cam 88

valve guIde puSher SetAmerican made by Rowe. This kit lets you push the guide into Evo heads rather than drive it in with a punch.t4804 Evo valve guide pusher

valve guIde drIver tool SetMade in America by JIMS, this deluxe set can be used for the removal and installation of valve guides.t4807 3 piece set

pISton rIng compreSSor SetSupplied with 6 bands ranging from 2 7/8 to 4 3/8. Fine tooth ratcheting motion to compress bands in small increments for accurate compression. Will not break or damage rings.t4465 Use on all models

pISton pIn keeper tool by JImSUsed to install retaining ring in piston.t4837 83-up Big Twin & L85-up Sportster

engine tools

17-13

crane valve SprIng Seat machInIng toolSCranes valve spring seat machining tools are job-shop quality with carbide cutting tips. They are used for lowering spring seats for high lift cams.e6700 84-up Evolution 80cc cuts spring seat to 1.475 o.d. Win part E6680 arbor requirede6710 48-84 61-80cc cuts spring seats to 1.630 o.d. Win part E6690 arbor required

valve SprIng compreSSor by JImS Necessary for installing or removing valves & springs. This compressor will hold center line of the two working ends to +.030. and eliminate the possibility of any binding. An acme thread is precision machined to a 32 finish and heat treated as are all other moving parts to give a full life time of service. Use a lube on threads.t4829 All models

valve guIde machInIng toolSCranes valve guide machining tools are job-shop quality with carbide cutting tips. They are used for machining valve guide outside diameters for our Teflon valve stem seals.e6670 48-84 61-80cc cuts 38 valve guides to .531 o.d. arbor includede6660 84-up Evolution 80cc cuts 516 valve guides to .531 o.d. arbor included

JImS conIcal valve SprIng compreSSor toolAdd this collar to your JIMS valve spring compressor tool to remove and replace valves and conical (bee hive) springs. A must have tool for safe valve work. t3651 05-up All Twin Cam except SE models 04-up XL & Buell

clutch tools

17-14

clutch SprIng tenSIon toolUse to release the clutch springtension for disassembly.t4858 Mid 84-90 Sportster

adapter nut forcompreSSor toolThis nut adapts to Win part T4872 which is a Clutch Spring Compressor forSportster. t4881 91-up Sportster

clutch SprIngcompreSSor by JImSRemoves and installs clutch components.t4849 71-84 XL repl. oem 97178-71

clutch lock plateThis tool is used to lock clutch shell to clutch hub, & for removing or installing clutch hub nut.t3665 41-84 Big Twin

5-Speed tranSmISSIon Shaft InStallerThis tool allows installation of transmission shafts without the use of a hydraulic or arbor press.t4658 All 5 & 6 Speed transmissions Including Twin Cam 88 A & B

17-15

clutch tools

maIn drIve gear Seal InStaller by JImSUse to install main drive gear oil seal to proper depth with transmission assembled. Comes with a protective sleeve for seal.t3675 All Big Twin 5 Speed models

drIve gear bearIng & Seal InStallerUse to install both bearings and the seal on the clutch side. 5 speed.t4885 80-90 Big Twin

maIn drIve gear tool by JImSThis tool removes and installs main drive gear and its bearing without removing the transmission. 5 speed.t4839 80-up Big Twin & 91-up Sportster

counterShaft Sprocket locknut wrench by JImSThis countershaft sprocket locknut wrench has an extra long two-piece design. Inner collar will retain wrench to nut for safer service work.t4831 36-up Big Twins repl. oem 94660-37a

ShIft fork gaugeSUse for setting and aligning shift forks.t4846 79-up Big Twin repl. oem 96385-78at4845 39-78 Big Twin repl. oem 96384-39

transmission tools

17-16

tranSmISSIon gearSpacIng tool by JImSUse this tool to check proper gear spacing. t4840 86-90 XL

tranSmISSIon race lappIng toolUse to line main race on the same center-line as the main shaft ball bearing, after installing new case race or fitting oversized rollers. This extremely rigid tool can be powered by a low speed drill motor from the ball bearing side.t4867 37-E77 Big Twin 4 speed

tranSmISSIon Stand for rubber mountFits all rubber mount 5 speed Big Twin transmissions except 93-up FLT & Dyna modelst4883 5 speed transmission stand

clutch aSSembly ServIce tool for bIg twInSThis tool will safely dissassemble and assemble the clutch shell assembly. Easily removes and installs the clutch hub from its bearing. Safely removes and installs the clutch shell ball bearing (H-D No.37906-90) without any damage to the new bearing. This is done by pushing on the outer perimeter of the bearing.t4452 90-up Big Twins

6 Speed twIn cam maIn drIve gear Seal InStallerThis tool is designed to properly align and install to the right depth, the main drive gear seal (H-D No.12077) into the end of the gear. This can be performed while the assembled transmission is either on a bench or in the motorcycle chassis.t4453 06-up FXD Twin Cams 07-up FXST & FL Twin Cams

17-17

transmission toolstranSmISSIon cover bearIng remover & InStallerUse this tool to remove and replace the transmission door bearings. It can also be used to remove the transmission door for replacement without removing the complete transmission assembly. Door bearings must be replaced if using this tool to pull door off case.t3690 80-up Big Twin 5 speed

tranSmISSIon Stud InStaller toolUse on all stock and aftermarket transmissions that use the bottom mounting studs.t4661 36-86 Big Twin 36-86 4 Speeds & 85-present Softail 5 Speeds

rocker buShIng reamer toolUse to fit rocker bushings in line witheach other.t4868 66-up Big Twins & 57-up XL

rocker buShIng & roller bearIng pullert4882 57-up Big Twin & XL

cylInder torque plateSThe JIMS torque plates are drilled for multiple application use, and can accommodate up to a 4 bore with stock EVO bolt pattern.t4684 66-present Big Twin single cam only, 86-present Sportster & 87-present Buell

cylInder torque plateSTo check cylinder measurements accurately these torque plates are essential. Simulate stress conditions when boring and honing. These plates are lasered with the correct torqueing sequence for big bore cylinders.t4893 Twin Cam 88, Jims T/C Big Bore cylinders, and all big Bore cylinders up to 4

transmission tools

17-18

crankShaft guIdeThis tool will spread crankcase pinion bearing rollers while reassembling right side engine case on the fly-wheel assembly.t4687 Twin Cam 88 A and B

twIn cam crankShaft buShIng reamer Use this tool when replacing crankshaft bushings. This tool will ream bushings for proper size, and align crankshaft to cam support plate.t4651 99-present Twin Cam 88

crankShaft bearIng toolDesigned to remove and replace the right crankcase bearing. Made of non marring delrin, use it to press the bearing in and out straight with no damage to the case.t4889 Twin Cam 88

outer race toolWorks on 55-68 Big Twin to remove Timken bearing outer race from crankcase. Also for use on 55-up Big Twins for installation of outer race. t4851 Race tool repl. oem 97194-57

breather reamer toolRepair a damaged breather hole with JIMStool. No need to disassemble the cases. Using the new reamer tool will repair a damaged breather hole to use at .030 oversize breather gear.t4676 36-present Big Twin

pIngel cylInder head holderThis threaded tool mounts in any bench vise in any position and holds cylinder head securely in place for all types of head work. Made of steel and plated with zinc, it offers 12mm threads on one end and 14mm threads on the other end. Use the 12mm end on EVO XL and Twin Cam and 14mm on all others. The shaft of the tool is also drilled out for clean and easy wall storage.t4440 Head holder

crankShaft buShIng remover & InStaller for twIn cam by JImSRemoves the crankshaft bushing in the support plate on a Twin Cam 88.t4899 Remover & Installer

miscellaneous tools

17-19

all prImary drIve lockIng toolUse on all primaries between front primary chain and motor sproket. Made out of black delrin.t4681 Locking tool

5-Speed maIn bearIng removerThis tool will remove the old bearing straight without possible damage to the transmission case, & without removing the transmission case.t4657 All Big Twin 5 and 6 Speed Twin Cam 88 A and B

Seal drIver early & late 5 SpeedSUse to install the main seal in transmission. This tool will press in the seal as flat and straight as possible to .050 below housing for a no leak fit. t4656 85-present Big Twin 5 & 6 Speeds & Twin Cam 88 A and B

maInShaft bearIng racetool by JImSThis tool is used to install and remove the bearing inner race on the transmission mainshaft.t4838 84-up Big Twin

5 Speed door pullerUse to remove Big Twin 5 Speed transmission door.This tool easily removes the transmission door with gears and shafts attached, without any scratches.t4659 80-present Big Twin 5 & 6 Speed transmission doors.

miscellaneous tools

17-20

multI puller by JImSThis hub puller will pull the clutch of a 45, all 3,5, & 10 finger Big Twin clutches as well as early and late sportster clutch. It also pulls Big Twin alternator cover, Big Twin Motor sprocket, and Sportster transmission sprocket. t4834 Clutch hub puller

clutch hub puller by JImSUse to remove wet and dry clutch hub without removing clutch release rod 4 bolts included.t4843 36-90 Big Twin, repl. oem 95960-52c

clutch hub pullerDeluxe clutch hub puller, late 70-84. Pulls clutch hub on 45s. Also pulls Big Twin clutch hubs 3, 5, or 10 finger, Big Twin & Sportster motor sprockets Big Twin rotor assembly & Sportster transmission sprockets.t4670 Clutch Hub Puller

clutch SprIng compreSSorUse this tool to release clutch spring for ease of retainer ring removal and installation.t4872 90-up Big Twin

dIaphragm clutch SprIng compreSSIon toolMakes it easy to remove and re-install retainer ring.t4862 90-later Big Twins & 91-later Sportster

17-21

miscellaneous tools

wheel bearIng race remover & InStaller toolThis tool is used to remove and install bearing races from JIMS.t4808 73-up Big Twin & Sportster

alSo needed:t4835 Handle for bearing race toolst4688 Tool driver spacer

bearIng attachmentS for wheel truIng & balancIng StandRowes truing and balancing stand is the same tool used in all the H-D service schools. It can true on centers or V slot and balance on ball bearings.

t4802 Bearing Attachment Kit for truing stand

t4802

late Sealed wheel bearIng remover and InStaller kItUse to remove and install new style sealed wheel bearings without damaging the wheel. Includes new 25mm, with or without ABS. Kit comes with 18 different parts.t4461 00-up Twin Cams 2000 Sportster & Buell 02-up V-Rods

SteerIng head bearIng race InStallerUse to install steering head races, stock and custom as well as install cups in a frame. This tool pulls the races and cups in straight and true without any damage.t4662 All models bearing race installer

SteerIng head bearIng race removal toolThis tool is used to remove and install steering head bearing race.t3660 49-up Big Twin & 78-up Sportster

alSo needed:t4835 Handle for bearing race toolst4688 Tool driver spacer

cleveblock SpreadIng toolUse to install the swing arm in a 5-Speed rubber mount frame. This tool will spread the swing arm cleveblocks allowing for installation of swing arm.t4665 80-present Big Twin Twin Cam 88 A and B

compenSatIng Sprocket Shaft nut wrenchUsed to remove and install compensating nut.t4859 55-70 Big Twin & Sportster repl. oem 94557-55a

buShIng aSSembly rear SwIng arm aSSembly toolUse to remove and replace swing arm cleveblocks. JIMS tool presses on the outer sleeve of the bushing, preventing damage to the cleveblock.t4666 80-present FLT, 82-94 FXR & all aftermarket FXR style frames

miscellaneous tools

17-22

Shock adJuStIng wrenchThis zinc plated shock wrench is used to adjust the spring compression of the rear shocks.f2127 67-up FX, FL, XL repl. oems 94700-65 & 94700-52b

Spoke wrenchHeavy-Duty spoke wrench to fit nipple sizes from 1 to 6. Sold eacht4660 Spoke wrench

Soft vISe JawSAmerican Made by Rowe, this quality set of aluminum jaws fits any size vise. Protects expensive parts from damage by regular vise jaws. Sold pair.t4800 Soft Vise jaws

oIl pump drIll JIg tool by JImSThis crankcase oil passage jig allows you to modify 73-80 Big Twin crankcases to accept later 81-91 style oil pumps. This includes Jims oil pumps, stock H-D and other aftermarket oil pumps 81-91.e1531 Oil pump drill jig

brake calIper pISton removerThis tool will support the brake caliper pistons for removal by holding the pistons square to their bores.t4664 2000-present H-D, 4 piston brake caliper

machInIng tool arborCranes machining tool arbors are required to use their spring seat machining tools with our parts E6700 & E7610e6690 38 valve guidese6680 516 valve guides

miscellaneous tools

17-23

crankcaSe oIl paSSage drIllIng JIgS&Ss crankcase oil passage drilling jig enables any builder to perform all the required and optional modifications necessary to install any S&S oil pump kit.t0100 Crankcase Oil Passage Drilling Jig

fork Seal & cap InStallerSUse to install fork seals, dust seals, and chrome caps. Lightly grease to keep from scratching fork tubes.t4678 39mm slider with Delrin plastict4679 41mm slider

35mm heX top fork nut Socket 3/8 drIveUse to remove or install to fork nut on glide forks. Has rubber protector on inside to prevent damage to the chrome nut.t4663 All Big Twins and Sportster

fork nut SocketUse to remove and install top fork tube plug. Eliminates possible burning of plug caused by wrenches.t4677 48-later Wide Glide models

miscellaneous tools

17-24

gaSket locator tool

t4450 3 piece set

twIn cam tImken caSe bearIng converSIon toolThis tool is a must for the big cubic inch late model Twin Cam engine builder. It may also be used to replace the bearing for stock 88 or 96 engines. Utilizing the special JIMS precision insert, it is designed to easily and accurately convert the left side crankshaft roller bearing (H-D No 24604-00D) to the more durable Timken bearing (HD No.9028). This insert is manufactured from aerospace quality steel that is several times stronger than the aluminum case material the standard bearing rides in. The tool includes: A new steel bearing insert held to under .0002 total indicator reading A press plate that will hold the bearing insert in line with the case bearing bore at the time it is being pressed into the case. All the necessary drill bits to drill oil feed and return holes, hardware and detailed instructions. This job can be performed with normal hand tools, a hand drill, and a 2 ton press.t4441 03-up All Twin Cam Engines

kit contains 19 parts1 Timken bearing insert 11 Screw, 10-24 X 1 SHCS2 Press plate 12 Roll tap3 Bottom locator plate 13 Base installer4 Big Twin press installer plug 14 Protective case5 Drill bit 15 Tap guide6 Drill stop collar 16 Screw, Flat phillips7 Drill bit 17 #620 loctite8 Drill stop collar 18 Screw, 3/8-16 X 2 SHCS9 Drill bit 19 Tap magic10 Drill stop collar

balance Shaft removal toolThis tool is designed to remove both front and rear counter balancer shaft bearing assembly from the left engine case on the new 96 and 110 Beta engines. t4442 07-up Softail

miscellaneous tools

17-25

oXygen SenSor Socket toolThis tool is used to remove or install the oxygen sensor on all closed loop fuel injected H-D models. Socket has a 3/8 drive receiver or can be used with a 7/8 wrench. Socket will withstand up to 125 ft/lbs of torque.t4451 Use on all 06-up EFI models

outer balance bearIng InStaller & remover toolThis tool removes and installs the outboard balancer bearing on the new 96 and 110 B Softail engines chain guide support plate. t4443 07-up Softail

fl power traIn alIgnment toolThis tool easily and safely aligns the power train (rubber mounted engine, transmission and the swingarm assembly) to the correct position as found on most touring models. Alignment service must be performed when the engine, transmission, or swingarm has either been removed or repaired. The safety in handling and performance of the motorcycle could be greatly effected without the accurate alignment this tool provides. t4446 93-up FLHT

prImary lockIng barSUse to lock primary for service work.t4464 07-up FL

miscellaneous tools

17-26

JImS Starter rIng gear rIvet fIXture toolUse to remove rivots from old starter ring gear on clutch basket. t4447 90-06 FXST, FL 90-05 FXR, FXD

Starter JackShaft Seal InStaller toolThis tool is designed to easily align and install the starter jackshaft seal (H-D No.12066) without distorting or damaging the seal. This seal is located in the upper part of the inner primary of Big Twins.t4448 99-06 FL Twin Cams 00-06 FXST Twin Cams 99-05 FXD Twin Cams 94-00 EVO Big Twins

Inner prImary cover bearIng & Seal InStaller / remover toolDesigned to safely remove and install the inner primary bearing, (H-D No.9135) without any damage to the new bearing. This is done by pushingon the outer perimeter of the bearing. Also removes and installs inner primary seal, (H-D No.12052A). This is the bearing and seal that the transmission mainshaft passes through.t4449 84-06 FXST, FL, FXR, FXD

hoSe repaIr kIt 1/4 - 5/16Hose bared end is .3125 (5/16), threaded end is 12mm. It can be used with either a .250 or .3125 hose.t4462 Hose repair kit

miscellaneous tools

17-27

twIn cam engIne rotator, from the flywheel Sprocket ShaftUse this tool to rotate the flywheel / piston assembly, with the engine still in the frame or on a bench. This tool is used to rotate the flywheel assembly. When doing pushrod adjustments, or when building big inch engines, checking operating clearances such as piston to piston, or valve to valve. Also can be used to hold the flywheel assembly from rotating when torquing the cam drive sprocket retention bolts. This tool has been manufactured with a long socket design making it easier to use without the use of a driver. For engine bench work we recommend that the engine be boltedin a engine stand. Caution: Not for use with an air or electric impact, this tool is only guaranteed for use with hand drivers. t4455 06-up FXD Twin Cams 07-up FXST & FL Twin Cams

twIn cam engIne rotator, from the flywheel Sprocket ShaftUse this tool to rotate the flywheel / piston assembly, with the engine still in the frame or on a bench. This tool is used to rotate the flywheel assembly. When doing pushrod adjustments, or when building big inch engines, checking operating clearances such as piston to piston, or valve to valve. Also can be used to hold the flywheel assembly from rotating when torquing the cam drive sprocket retention bolts on Twin Cams or pinion shaft nut or single cam models. This tool has been manufactured with a long socket design making it easier to use without the use of a driver. For engine bench work we recommend that the engine be boltedin a engine stand. Caution: Not for use with an air or electric impact, this tool is only guaranteed for use with hand drivers. t4456 06-up FXD Twin Cams 07-up FXST & FL Twin Cams

Sprocket Shaft / flywheel holderUsed to hold flywheel assembly in vise, for assisting assembly or dissassembly with or without left case attached. Can also be used to check case clearance on stroker flywheels.t4463 06-up FXD Twin Cams 07-up FXST & FL Twin Cams

miscellaneous tools

17-28

JImS # wIn #

959 t4441

960 t4442

961 t4443

962 t4444

963 t4445

964 t4446

965 t4447

966 t4448

967 t4449

968 t4450

969 t4451

971 t4452

972 t4453

973 t4454

974 t4463

975 t4455

976 t4456

1001 t4807

1003 t4865

1007 t4866

1010 t4857

1022 t4810

JImS # wIn #

2237 t3645

2243 t4682

2244 t4663

2245 t3665

2246 t4683

2256 t3675

2260 t3670

2280 t3685

2281 t3680

2283 t4659

2312 t4464

2341 t3655

2388 t4688

2528 t4674

1004a t4834

1006t t4832

1008-5 t4883

1012-70tb t4863

1013-54tb t4864

1023-70 t4876

1041-tc t4884

1042-8 t4461

tImken bearIng or race InStaller adapter kItThis tool will upgrade part# T4860 bearing installer tool to work on the latest fine spline Twin Cam sprocket shafts. This tool is designed install either H-D No.9028 Timken bearing or the roller bearing race from H-D No.24004-03 bearing assembly onto the sprocket shaft as shown.t4454 06-up FXD Twin Cams 07-up FXST & FL Twin Cams JIMS 120 or 131 motors

bearIng and race puller toolThis tool has been designed to remove the flywheel sprocket shaft inner bearing race with the supplied T-bar and hardware. t4445 03-up Twin Cams Use to remove Timken bearing (H-D No. 9028) or No. 9029 on Big Twins, 1955 Panhead to present Twin Cam, including JIMS 120 or 131 engines. Use to remove the flywheel sprocket shaft inner bearing race or the Timken bearing. Also removes pinion shaft inner bearing race on Sportster 1954-up, including all Buell to present. Use to correctly remove press fit transmission gears and bearings from input and output shafts on all V-Rod models 02-up.

miscellaneous tools

JImS toolS croSS reference chartJImS # wIn #

1034 t4654

1042 t4667

1048 t4655

1050 t4661

1051 t4897

1073 t4684

1078 t3690

1095 t4878

1148 t4653

1162 t4664

1166 t4685

1167 t4686

1169 t4828

1177 t4907

1236 t4465

1275 t4889

1276 t4888

1277 t4892

1278 t4891

1279 t4894

1280 t4898

1281 t4899

JImS # wIn #

1283 t4895

1284 t4652

1285 t4896

1287 t4893

1288 t4687

1668 t4816

1705 t4890

1706 t4676

1707 t4665

1708 t4668

1720 t4657

1725 t4662

1743 t4666

1800 t4930

2043 t4677

2044 t4678

2047 t4679

2188 t3650

2189 t4658

2232 t3660

2233 t4680

2234 t4681

JImS # wIn #

1044-tS t4874

1045-tS t4875

1047-tp t4869

1087-2 t4462

1094c t4827

1169-1 t4833

2347-7cb t4669

33071-73 t4808

33416-80 t4835

33443-84 t4836

34623-83 t4837

34734-81 t4885

34761-84 t4858

34902-84 t4838

35316-80 t4839

35820-86 t4840

38515-90 t4872

39361-69 t4841

94547-80a t3222

94547-80b t3223

94555-55a t4850

94557-55a t4859

JImS # wIn #

94660-37a t4831

94804-57 t4868

94805-57 t4830

95660-85 t4656

95724-57 t4842

95760-57 t4882

95760-tb t4873

95760-tp t4870

95760-Xl t4880

95960-52c t4843

95970-32c t4844

96384-39 t4845

96385-78a t4846

96600-36b t4829

96710-tl t4871

967740-36 t4847

96830-51 t4848

97081-54 t3225

97178-71 t4849

97225-55 t4860

97272-60 t4886

97273-60 t4887

17-29

tool kit & boxes

17-30

bIker travelIn tool kItWin does it again! Our kit has everything you need to make minor repairs on the road in a handy zip-up pouch. Kit includes: pliers, spark plug wrench, screw driver with 6 bits, 1/4 bit with 6 sockets, 3/16 to 1/2, 4 open end wrenches, 3/8 to 3/4, and an all-in-one box wrench. 9 X 5 when zipped shut. Big seller!t4710 Biker Travelin Tool Kit

kIdney tool boXThis quality chrome plated OEM style reproduction comes complete with lock & keys. Perfect for restoration or the custom look. t4650 Kidney tool box repl. oem 64205-40

kIdney tool boX mountIng bracketS for SoftaIlSChrome kidney Tool Box mounting bracket.Necessary for mounting T4650 toolbox. For all 84-up Softail except 90-up Heritage Softail Classic.t4730 Left side

kIdney tool boX mountIng bracket for fX & fXwgChrome mounting bracket for our T4650 toolbox. Stock passenger pegs may be turned upside down or relocated to the bottom shock stud where earlier models had them.t4740 77-86 FX & FXWG

heavy-duty chaIn breakerA compression screw forces the pin out of the chain to aid in the removal of links used on all 420 to 630 size chain.t3521 Chain breaker repl. oem 94480-89

17-31

Wheel chocks & sPacerspIngel wheel chockThe Pingel wheel chock secures your bike in a truck or trailer and features quick and easy removal. It features heavy-duty thick wall steel construction, steel flush-mount floor attachments and easy installation and removal. They feature a high quality, lustrous chrome finish.g3482 5 I.D. Wheel chockg3484 3 I.D. Wheel chock g3471 Mounting hardware

chrome plated SpacerSI.D.s 1/4 and 5/16 lengths from 1/4 1 1/4

f6555160 Pieces - 16 Sizes

I.D.s 3/8 and upf6556114 Pieces - 12 Sizes

Spacer refIllS for f6555 10 packSpart# Id od lengthf6522 1/4 7/16 3/16f6523 1/4 7/16 1/4f6524 1/4 7/16 3/8f6525 1/4 7/16 5/8f6526 1/4 7/16 3/4f6527 1/4 7/16 7/8f6528 1/4 7/16 11/16f6529 5/16 1/2 3/16f6530 5/16 1/2 1/4f6531 5/16 1/2 1/2f6532 5/16 1/2 3/4f6533 5/16 1/2 1f6534 5/16 1/2 1f6535 5/16 1/2 17/32f6537 3/8 9/16 1/8f6539 3/8 13/16 5/32

Spacer refIllS for f6556 10 packSpart# Id od lengthf6540 3/8 5/8 1/4f6541 3/8 5/8 1/2f6542 3/8 5/8 3/4f6543 3/8 5/8 1f6544 3/8 5/8 1f6537 3/8 9/16 1/8f6545 7/16 11/16 5/16f6546 3/8 13/16 1/2f6547 7/16 3/4 3/32f6548 3/8 1 5/16f6549 5/8 1 3/8f6550 1/2 11/16 5/16

bearings & lock

17-32

mIScellaneouS bearIngSA wide selection of bearings is listed for a variety of applications. Bearings are listed by OEM for easy cross-reference.

part # bearIng applIcatIon b3900 8888 84-up XL Countershaft low gear b3901 8904 Big Twin 5 speed Mainshaft 5th gear needle bearing b3902 8905 77-81 Big Twin Main Drive Gear b3904 9008 63-78 XL Rear Wheel, 54-72 XL & 71-72 FX Front Wheel b3905 9009 Same As Above, Shielded b3906 9010 54-72 Sportster Rear Wheel double row b3907 9020 41-85 4 speed Transmission Mainshaft b3908 9025 54-up Sportster Transmission Mainshaft b3926 9028 69-up Big Twin Timken Case Bearing Set with Spacers b3927 9029 55-68 Big Twin Timken Case Bearing Set with Spacers b4910 9040 70-87 Big Twin Chain Housing h3030 9052 73-up Big Twin Front & Rear Wheel, 73-up Sportster Front Wheel, 79-up Sportster Rear Wheel includes Races Sold pair b3925 9052 Same as above Timken Sold each b3911 9057 58-up Sportster Cam Gear needle bearing e4970 9058 58-up Big Twin Cam Gear needle bearing b3912 9062 65-up Big Twin & 67-80 Sportster Starter Shaft Housing needle bearing e4430 9063 65-up Big Twin & 67-80 Sportster Chain Housing Cover needle bearing b3920 9076 Softail Swingarm Bearings with Snap rings Sold in pairs b3914 9088 58-69 BT & 58-81 XL Generator End Cover needle bearing with seal b3930 24626-87 Big Twin Pinion Bearing white/grey b3931 24628-87 Big Twin Pinion Bearing green b3932 24641-87 Big Twin Pinion Bearing red b3933 24643-87 Big Twin Pinion Bearing blue b3935 24660-87 XL Pinion Bearing green b3936 24650-87 XL Pinion Bearing red b3937 24647-87 XL Pinion Bearing blue b3928 24729-52 54-76 XL Timken Left Case Bearing Set with Spacers b3929 24729-74 77-up XL Timken Right Case Bearing Set with Spacers b3915 31539-66 66-82 Big Twin & 67-80 Sportster Starter Motor Drive End b3916 35960-54 54-up Sportster Countershaft closed end needle bearing b3917 35961-52 77-85 BT 4 speed C/shaft, Clutch & 54-up XL Gear & C/shaft open end needle b3924 45586-78 78-81 XL Timken Bearing Head Cup b3918 48300-60 60-up Big Twin & 82-up XL Fork stem Steering Head Bearing & Race b3922 48300-60 60-up Big Twin & 82-up XL Fork stem Steering Head Bearing only Timken b3919 48315-60 60-up Big Twin & 82-up XL Fork stem Steering Head Race only b3923 48315-60 60-up Big Twin & 82-up XL Fork stem Steering Head Race only Timken

repl. oem

pIngel lockSterThe Pingel Lockster was designed to store a padlock on your motorcycle when the lock is not securing the motorcycle. It is made of polished stainless steel so it wont rust or corrode. Installation is fast & easy using existing bolt holes. No drilling is required. It can be installed on the forward frame yoke below the steering pin or on one of the highway peg mounting plate bolts, forward frame yoke cross brackets, fork leg trim lower bolts or upper crash bar bolts. Lockster fits H-D logo lock, Master Lock 220, American lock H-10. g3497 Master Lock 220g3498 Lockster

g3497

g3498

17-33

fastener assortments

chrome allen Screw aSSortmentS & refIllSGardner-Westcotts Assortments organize styles & sizes for fast access. These allen screws are high quality chrome and have knurls polished off. Assortment containers are labeled with size for quick reorder time.f4830 Coarse assortment, sizes 1/4 thru 3/8, 24 sizes, 220 pieces.f4840 Fine assortment, sizes 1/4 thru 3/8, 23 sizes, 210 pieces.

chrome heX head bolt aSSortment and refIllSf4872 Coarse assortment 1/4 thru 3/8, 24 sizes, 220 piecesf4873 Fine assortment 1/4 thru 3/8, 24 sizes, 220 pieces

chrome allen Screw refIll 10 packS8/32 10/24 10/32 1/4 - 20 1/4 - 28 5/16 - 18 5/16 - 24 3/8 - 16 3/8 - 24 SIZe

f4011 f4016 f4022 1/2 f4012 f4017 f4023 f4990 f5080 f5150 f5240 5/8f4013 f4018 f4024 f5000 f5090 f5160 f5251 f5320 f5380 3/4

f5010 f5100 f5170 f5250 7/8f4015 f4019 f4025 f5020 f5110 f5180 f5260 f5330 f5390 1

f4021 f5030 f5120 f5190 f5270 f5340 f5400 1 1/4f5040 f5130 f5200 f5280 f5350 f5410 1 1/2f5050 f5140 f5210 f5290 f5360 f4520 1 3/4f5060 f5220 f5300 f5370 f5430 2f5070 f5230 f5310 f5440 2 1/4

f5450

chrome heX head refIll 10 packS1/4

- 201/4

- 241/4 - 28 5/16

- 185/16 - 24

3/8 - 16

3/8 - 24

SIZe

f6445 f6470 f6474 1/2 f6446 f6475 f6455 f6484 5/8f6447 f6471 f6476 f6456 f6485 f6464 f6492 3/4f6448 f6472 f6477 f6457 7/8f6449 f6473 f6478 f6458 f6486 f6465 f6493 1f6450 f6479 f6459 f6487 f6466 f6494 1 1/4f6451 f6480 f6460 f6488 f6467 f6495 1 1/2f6452 f6481 f6461 f6489 f6468 f6496 1 3/4f6453 f6482 f6462 f6490 f6469 f6497 2f6454 f6483 f6463 f6491 f6498 2 1/4

chrome flathead allen bolt aSSortment and refIllSf5207 Assortment contains 24 sizes, 240 pieces

chrome flathead refIll 10 packS8/32 10/24 10/32 1/4 - 20 5/16 - 18 5/16 - 24 3/8 - 16 3/8 - 24 SIZe

f5208 f5211 f5216 1/2 f5209 f5212 f5217 f5219 f5223 f5228 3/4

f5213 f5218 f5221 f5224 f5229 f5241 f5234 1f5214 f5222 f5226 f5231 f5233 f5236 1 1/4

f5227 f5232 f5238 f5237 1 1/2f5239 2

fastener assortments

17-34

button head allen ScrewaSSortment and refIllSf4871 Coarse assortment 1/4 thru 3/8 24 sizes 112 pieces.

chrome locknut aSSortmentThis set features 11 sizes from 10/24 thru 7/16-20 both coarse and fine thread. f6191 190 pieces.

chrome flat lock waSher aSSortmentThis set features 8 sizes of flat and lock washers from #8 thru 5/8. f4860 960 pieces.

chrome acorn aSSortmentThis set features 11 sizes from 10/24 thru 5/8-18 both coarse and fine thread. f4850 182 pieces.

chrome heX nut aSSortmentThis set features 16 sizes from 6/32 thru 5/8-18 both coarse and fine thread. f4870 534 pieces.

button head Screw refIll 10 packS8/32 10/24 10/32 1/4 - 20 1/4 - 28 5/16 - 18 5/16 - 24 3/8 - 16 3/8 - 24 1/2 - 13 SIZe

f6588 f6592 f6597 f6192 f6426 f6415 f6433 f6421 f6440 1/2 f6589 f6593 f6598 f6193 f6427 f6416 f6434 5/8f6590 f6594 f6599 f6194 f6428 f6417 f6435 f6422 f6441 f6166 3/4

f6195 f6429 f6418 f6436 7/8f6591 f6595 f6600 f6196 f6430 f6419 f6437 f6423 f6442 1

f6596 f6197 f6431 f6420 f6438 f6424 f6443 1 1/4f6198 f6432 f6601 f6439 f6425 f6444 1 1/2f6199 f6602 f6604 1 3/4f6413 f6603 f6605 2f6414 2 1/4

chrome heX nut, acorn nut, locknut, flat waSher and lock waSher refIll packS6/32 8/32 10/24 10/32 1/4

- 201/4

- 285/16 - 18

5/16 - 24

3/8 - 16

3/8 - 24

7/16 - 14

7/16 - 20

1/2 - 13

1/2 - 20

5/8 - 11

5/8 - 18

SIZe

f557010 pk

f5580 10 pk

f559010 pk

f560010 pk

f561010 pk

f5620100 pk

f5630100 pk

f5640100 pk

f5650100 pk

f5660100 pk

f567050 pk

f568050 pk

f569010 pk

f570010 pk

f571010 pk

f572010 pk

heX nut

f546010 pk

f547010 pk

f548010 pk

f549010 pk

f550010 pk

f551010 pk

f552010 pk

f553010 pk

f554010 pk

f555010 pk

f556010 pk

acorn nut

f650920 pk

f651020 pk

f649920 pk

f650020 pk

f650120 pk

f650220 pk

f650320 pk

f650420 pk

f650520 pk

f650620 pk

f650820 pk

f650720 pk

lock nut

f573010 pk

f574010 pk

f5750100 pk

f5760100 pk

f5770100 pk

f578050 pk

f579010 pk

f580010 pk

flat waSherS

f581010 pk

f582010 pk

f5830100 pk

f5840100 pk

f5850100 pk

f586050 pk

f587010 pk

f588010 pk

lock waSherS

17-35

fastener assortmentswaSher aSSortmentS & refIllS by gardner-weStcott

Assortment containers are labeled with size for quick reorder time. These assortments are specially designed for specialty applications on Harley-Davidson motorcycles.

f4215

f4215 1/2 Id waSher aSSortment

refIll no. type & SIZe qty

f5005 rocker Shaft waSher 20

f5015 head bolt waSher 1/2 8

f5025 1/2 X 1 1/4 20

f5035 aXle waSher 5/8 20

f5045 trIple tree waSher 5/8 20

f5055 trIple tree nut 1 waSher 20

f5065 fender mount waSher 3/8 20

f5075 head bolt cyl. 7/16 20

f5085 7/16 X 15/16 20

f5095 top motor mount. 1 20

f5105 top motor mount. 1 1/8 20

f5115 top motor mount. 7/8 20

f5125 tank mount. 5/16X 1 1/8 20

f5135 fender mount. 5/16X 1 1/4 20

f5145 motor mount. 5/16 20

f5155 motor mount. 3/8 20

f5165 evo head bolt waSher 3/8 10

f5175 3/8 X 7/8 20

f5185 SIde cover waSher 1/4 20

f5195 rocker boX waSher 1/4 20

f5205 taIl lIght mount 1/4 20

f5215 rocker boX waSher 5/16 50

f5225 5/16 X 3/4 20

f5235 5/16 X 1 1/32 10

f4205 waSher aSSortment for h-d

refIll no. type & SIZe qty

f5245 banJo bolt waSher 12mm 20

f5255 braSS oIl pump waSher 20

f5265 draIn Screw nylon 1/2 20

f5275 oIl draIn plug 1/2 81-up 20

f5285 draIn plug nylon 5/8 20

f5295 tranS. oIl fIll waSher 4 Spd. 20

f5305 chrome an flat waSher 3/8 20

f5315 nylon 3/8 20

f5325 neoprene S/S 3/8 20

f5335 banJo boltS alum. 10mm 20

f5345 nylon 7/16 20

f5355 rocker Shaft S/S 20

f5365 oIl Screen/pump, braSS 20

f5375 1/4 copper v2 rocker boX 20

f5385 neoprene S/S 1/4 20

f5395 braSS fork draInS 8mm 20

f5405 nylon 5/16 20

f5415 neoprene S/S 5/16 20

f5425 fork draIn 4mm 20

f5435 oIl pump nylon #8 20

f5445 nylon #10 20

f5455 neoprene S/S #10 20

f5465 nylon SIde coverS 1/4 20

f5475 Seat mount nylon 1/4 20

f4205

electrIcal termInal aSSortment & refIllS by gardner-weStcottContaining 322 pieces and 24 sizes in a metal tray, this Electrical Terminal Assortment has been put together with the motorcycle mechanic in mind. Assortment containers are labeled with size for quick reorder time. R indicates red, B indicates blue & Y indicates yellow. Refill part numbers & quantities are also listed in charts.

f4880

f4880 electrIcal termInal aSSortment

refIll no. termInal type qty

f5890 #6 rIng end b 10

f5900 #8 rIng end b 10

f5910 #10 rIng end b 10

f5920 1/4 rIng end b 10

f5930 5/16 rIng end b 10

f5940 3/8 rIng end b 10

f5950 #6 Spade end b 10

f5960 #8 Spade end b 10

f5970 #10 Spade end b 10

f5980 #8 rIng end r 10

f5990 #10 rIng end r 10

f6000 1/4 rIng end y 10

f6010 5/16 rIng end y 10

f6020 3/8 rIng end y 10

f6030 female SlIde connector b 10

f6040 male SlIde connector b 10

f6050 InlIne connector b 10

f6060 butt connector r 10

f6070 butt connector b 10

f6080 butt connector y 10

f6090 #6 rIng end r 10

f6100 1/4 Spade end b 10

f6110 Snap plug recept. b 10

f6120 Snap plug b 10

fastener assortment & harDWare

17-36

chrome rocker boX hardware Set by gardner-weStcottThese chrome 12 point screws fasten Rocker Box to Evolution Motors. Includes washers forall Evolution Enginesf4055 12 point Rocker Box screws

chrome oIl pump fIttIng Set by gardner-weStcottDress up your Big Twins Oil Pump with this 5 piece fitting set from Gardner-Westcott.f4035 84-91 Big Twin

oIl fIlter mountIng Set f4185 92-up EVO

fatbob tank mount kIt With shimsf4145 88-up Fatbob

tranSmISSIon allen Screw SetS by gardner-weStcottf6101 87-up 5 speeds & Dyna Transmission Side Cover f6102 80-86 5 speeds & Dyna Transmission Side Cover f6161 91-98 Dyna Glide Transmission Top & Bottom Cover Includes oil fill cover and speed sensor mountf6162 88-97 5 speeds Transmission Top Cover

builDer kits & motor sets

f4010

chrome motor SetSBig Twin sets include hardware for side covers, lifter base, timing plug, inner primary mount, motor mount top, front & rear, rocker box covers Pan & Evo, header mount, point cover or generator mount. Sportster sets include hardware for cam & primary, generator or oil filter mount, sprocket, rocker box, top motor mount, lifter base, point or magneto cover.

motor SetS for bIg twInS

part# applIcatIon

f4058 2007-up SoftaIl twIn cam

f4066 2007-up flt twIn cam

f4071 2007-up dyna glIde

f4037 2000-06 SoftaIl twIn cam

f4036 1999-06 dyna glIde

f4038 1999-06 flt twIn cam

f6511 1991-98 dyna glIde

f6512 1991-98 flt & fXr

f6513 1987-91 flt & fXr

f6514 1987-99 fXSt & flSt modelS

f6515 1977-84 fX & flh 4 Spd modelS

f6516 1970-76 fX & flh all modelS

f4165 S&S bIg twIn motor caSeS

motor SetS for SportSter

f6517 1991-03 Xl modelS

f6518 1986-90 Xl modelS

f6519 1977-e84 Xl modelS

f6520 1971-76 Xl modelS

17-37

buIlder faStener SetS for evo bIg twInS

part# applIcatIon

f4057 2007-up twIn cam SoftaIl modelS

f4064 2007-up twIn cam flt modelS

f4069 2007-up dyna glIde modelS

f5203 2000-06 twIn cam SoftaIl modelS

f4972 1999-06 twIn cam dyna glIde

f5204 1999-06 twIn cam flt modelS

f4115 1996-99 fXSt & flSt

f5206 1996-98 dyna glIde modelS - chrome

f4075 1996-98 dyna glIde modelS - polIShed

f4125 1996-98 flt

f4970 1992-95 dyna glIde modelS

f6140 1991-95 fXr & flt

f4020 1987-90 fXr & flt

f4010 1987-95 fXSt & flSt

f4030 1986 fXSt & flSt

f4040 1984-86 fXr & flt

f4050 1985-86 4-Spd & 84 & 85 fXSt

buIlder faStener SetS for SportSter

f6121 1991-03 evolutIon Xl

f4100 1986-90 evolutIon Xl

f4110 1985 Iron head alternatorS

f4120 1979-84 SportSter

f4130 1977 & 78 Xl

f4140 late 1973-76 Xl

chrome allen head buIlder faStener SetS Builder sets Contain Timing Plug, Oil Pump, Left & Right Side Covers, Clutch & Chain Cover, Top Front & Rear Motor Mount with all Stabilizing Link Fasteners & Regular Bracket Mt. on FXR & FLT Models, Lifter Base, Point Cover, Header Mount, Casing & Inner Primary to Casing, Rocker Box, Cylinder Base, Motor Case & Transmission Cover.

buIlder faStener SetS for Shovelhead & panhead

part# applIcatIon fItment

f4060 1982 & 83 fXr

f4070 1979-84 fX & flh

f4080 1977-78 fX & flh

f4090 1970-76 fX & flh

f4890 1966-69 Shovelhead

f4900 1965 panhead

f4910 1958-64 panhead

f4920 1948-57 panhead

assorteD fasteners

17-38

SpecIalty faStener by gardner-weStcottTop quality American made fastener. 10 pack

chrome allen Screw SIde cover SetS All high quality polished chrome. All you need to complete the job. American made.

Cam and Primary Cover Sets Include: Transmission, chain clutch, and derby.

f6141

f4980 f4930 f6122

allen Screw SIde cover SetS SportSter

part # applIcatIon fItmentf6122 cam & prImary 91-up Xlf4200 cam & prImary 86-90 Xlf4210 cam & prImary 77-85 Xlf4220 cam & prImary 71-76 Xlf6141 SIde cover waSherS,

bag of 100 chromed

allen Screw SIde cover SetS bIg twInSpart # applIcatIon fItmentf4026 cam prImary tranS 2000-up twIn camf4028 cam prImary tranS 99-up fXd f4027 cam prImary tranS 99-up flt tcf4980 SIde cover Set 1991-98 dyna glIdef4160 cam prImary tranS 87-99 SoftaIlf4150 cam prImary tranS 87-98 flt & fXrf4170 cam prImary tranS 85-86 flt & fXrf4180 cam prImary tranS - 80-84 flt & fXrf4190 cam prImary tranS - 70-84 fX & flhf4930 cam prImary InSpectIon 65-69f4940 cam prImary InSpectIon 36-64f4135 tranS mount Set 89-99 SoftaIl modelSf4175 tranS top cover kIt, 91-98 dynaf6141 1/4 SIde cover waSherS

bag of 100 chromedf5770 3/8

part # repl. oem deScrIptIon Sold SIZe

f6171 16831-83 evo top motor mount 10 pk 3/8-16-24 X 2 3/16

f6172 16715-83 evo rocker boX & eXhauSt 10 pk 5/16-18-24 X 1 11/16

f6173 24820-78 carb. mount 10 pk 5/16-18 X 1 11/16

f6174 29253-78 carb. mount 10 pk 5/16-18 X 1 3/4

f6175 29254-78 carb. mount 10 pk 5/16-18 X 1 1/4

f6165 38130-71 Slotted clutch Set Screw for Xl 10 pk 3/8-24 X 1 1/2

f6111 16830-54 cylInder baSe for 900 Xl each 3/8-16-24 X 2-5/16

f6112 16830-72 cylInder baSe for 1000 Xl each 3/8-16-24 X 2-11/32

f6113 16831-30 cylInder baSe for 74 cu each 7/16-20-14 X 2-1/2

f6114 16837-78 cylInder baSe for 80 cu each 7/16-14-20 X 2-3/8

f6115 16837-85a cylInder head for late evo b.t. each 3/8 X 6-11/16 Spec.

f6116 16832-86a cylInder head for evo Xl each 3/8 X 5-3/4 Spec.

part # deScrIptIonf6163 clutch plate removal waSher, bt thru 84, ZInc platedf6164 clutch adJuStment Screw 41-84 bt repl. oem 31357-41

common Style h-d StudS by gardner-weStcottA wide variety of top quality American made studs listed by OEM for easy reference.

Some are sold in packs of 10 while others are sold each. See Sold column.

17-39

assorteD fasteners & kitsmotor tranS dreSS-up kIt for twIn cam 88 chromeKits for Twin Cam include hardware for motor case, trans to motor, coil cover, trans top & side covers, trap door, primary inner & outer, lifter base, crank shaft position sensor, points cover, motor mounts, rocker box, cam cover & oil filter mount.wIn# deScrIptIon f6263 2000-up TC88B Softail FXST, FLST f6264 99-up TC88 Dyna Glide f6265 99-up TC88 FLT

Stock Style replacement faStenerby gardner-weStcott

A wide variety of top quality American made fastener listed by OEM for easy reference. 10 pack

motor mount bolt SetSf4690 84-up FXSTf4680 48-84 Big Twin 4 speed

part # repl. oem deScrIptIonf6166 868 button allen Screw -13 X f6168 6007 oIl tank & tranSmISSIon draIn nylon waSher, f6169 6114 copper waSher evo rocker boXf6170 6410 nylon waSher - Seat mount fX - Idf6176 6655 fork top bolt waSher - 39mm chromef6177 31433-84 wet clutch derby cover waSher nylon f6178 45405-75a Screw damper tube Xl, fXr & fltf6179 41734-73 brake arm bracket mount - rear dISc -13 boltf6180 44174-77 brake calIper mount Screw front - Short chromef6181 44173-77 brake calIper mount Screw front - long chrome

motor tranS dreSS up kIt for bIg twIn chromeThese Evo Kits include hardware for rocker box, lifter base, cam cover, points cover, primary inner & outer, tranny top & side covers, trap door, & motor mounts.wIn# deScrIptIon f6266 87-99 EVO Softail FXST, FLST f6267 91-98 Dyna Glide f6268 91-98 FLT

17-40

garDner-Westcott cross reference gw # wIn #

10130 f4011

10132 f4012

10134 f4013

10138 f4015

10154 f4016

10155 f4022

10156 f4017

10157 f4023

10158 f4018

10159 f4024

10162 f4019

10163 f4025

10166 f4021

10208 f4990

10209 f5080

10210 f5000

10211 f5090

10212 f5010

10213 f5100

10214 f5020

10215 f5110

10218 f5030

10219 f5120

10220 f5040

10221 f5130

10222 f5050

10223 f5140

10224 f5060

10226 f5070

10272 f5150

10273 f5240

10274 f5160

10275 f5250

10278 f5170

10279 f5251

10280 f5180

10281 f5260

10284 f5190

10285 f5270

10286 f5200

10287 f5280

10288 f5210

10289 f5290

10290 f5220

10291 f5300

10292 f5230

10293 f5310

10326 f5320

10327 f5380

10330 f5330

10331 f5390

gw # wIn #

10334 f5340

10335 f5400

10336 f5350

10337 f5410

10338 f5360

10339 f5420

10340 f5370

10341 f5430

10343 f5440

10345 f5450

10428 f6608

10429 f6613

10430 f6609

10431 f6614

10432 f6610

10433 f6615

10436 f6611

11206 f6445

11207 f6474

11208 f6446

11209 f6475

11210 f6447

11211 f6476

11212 f6448

11213 f6477

11214 f6449

11215 f6478

11218 f6450

11219 f6479

11220 f6451

11221 f6480

11222 f6452

11223 f6481

11224 f6453

11225 f6482

11226 f6454

11227 f6483

11272 f6455

11273 f6484

11274 f6456

11275 f6485

11278 f6457

11280 f6458

11281 f6486

11284 f6459

11285 f6487

11286 f6460

11287 f6488

11288 f6461

11289 f6489

11290 f6462

gw # wIn #

11291 f6490

11292 f6463

11293 f6491

11326 f6464

11327 f6492

11330 f6465

11331 f6493

11334 f6466

11335 f6494

11336 f6467

11337 f6495

11338 f6468

11339 f6496

11340 f6469

11341 f6497

11343 f6498

11428 f6616

11429 f6621

11431 f6622

11432 f6618

11433 f6623

11436 f6619

11489 f4451

13130 f6588

13132 f6589

13134 f6590

13138 f6591

13154 f6592

13155 f6597

13156 f6593

13157 f6598

13158 f6594

13159 f6599

13162 f6595

13163 f6600

13166 f6596

13206 f6192

13207 f6426

13208 f6193

13209 f6427

13210 f6194

13211 f6428

13212 f6195

13213 f6429

13214 f6196

13215 f6430

13218 f6197

13219 f6431

13220 f6198

13221 f6432

13222 f6199

gw # wIn #

13224 f6413

13226 f6414

13270 f6415

13271 f6433

13272 f6416

13273 f6434

13274 f6417

13275 f6435

13278 f6418

13279 f6436

13280 f6419

13281 f6437

13284 f6420

13285 f6438

13286 f6601

13287 f6439

13288 f6602

13290 f6603

13322 f6421

13323 f6440

13326 f6422

13327 f6441

13330 f6423

13331 f6442

13334 f6424

13335 f6443

13336 f6425

13337 f6444

13338 f6604

13340 f6605

13445 f5236

14130 f5208

14134 f5209

14154 f5211

14155 f5216

14158 f5212

14159 f5217

14162 f5213

14163 f5218

14166 f5214

14210 f5219

14214 f5221

14218 f5222

14274 f5223

14275 f5228

14280 f5224

14281 f5229

14284 f5226

14285 f5231

14286 f5227

14287 f5232

gw # wIn #

14331 f5234

14334 f5233

14336 f5238

14337 f5237

14340 e5239

15546 f5610

15547 f5620

15548 f5630

15549 f5640

15551 f5660

15552 f5670

15553 f5680

20049 f6529

20050 f6530

20051 f6531

20052 f6532

20053 f6533

20054 f6534

20067 f6540

20069 f6541

20070 f6542

20072 f6543

20075 f6544

20080 f6522

20081 f6523

20082 f6524

20083 f6525

20084 f6526

20085 f6528

20087 f6537

20088 f6545

20091 f6539

20092 f6546

20093 f6535

20094 f6527

22334 f4975

22418 f4085

22420 f4795

22490 f4095

23200 f6550

23203 f6141

23569 f5750

23571 f5770

23572 f5780

23573 f5790

23575 f5800

23580 f6547

23593 f6163

24569 f5830

24570 f5840

24571 f5850

gw # wIn #

24572 f5860

24573 f5870

24575 f5880

31430 f6617

61103 f6111

61104 f6112

61105 f6113

61106 f6114

61200 f6115

61201 f6116

69554 f3496

03-15550Sw f5650

03-21547Sw f5490

03-21548Sw f5500

03-21551Sw f5530

03-21555Sw f5550

03-23204Sw f5185

03-23570Sw f5760

09106/20pk f5295

09340/10pk f6180

09341/10pk f6181

09418/10pk f6179

09566/10pk f6177

09566/20pk f5465

09568/10pk f6169

09568/20pk f5375

09570/20pk f5395

09570/20pk f5395

09571/20pk f5255

09574/20pk f5005

09579/20pk f5335

09825/20pk f5245

09985/20pk f5425

10774low/10pk f6178

11250/10pk f6470

11251/10pk f6471

11252/10pk f6472

11256/10pk f6473

13414/10pk f6166

15538Sw f5570

15540Sw f5580

15542Sw f5590

15543Sw f5600

15554Sw f5690

15555Sw f5700

15558Sw f5710

15559Sw f5720

17542/20pk f6509

17543/20pk f6510

17546/20pk f6499

17547/20pk f6500

17-41

garDner-Westcott cross reference gw # wIn #

17548/20pk f6501

17549/20pk f6502

17550/20pk f6503

17551/20pk f6504

17552/20pk f6505

17553/20pk f6506

17555/20pk f6508

17559/20pk f6507

20091/20pk f5155

21542Sw f5460

21543Sw f5470

21546Sw f5480

21549Sw f5510

21550Sw f5520

21553Sw f5540

21559Sw f5560

23200/8pk f5015

23214/20pk f5205

23274/20pk f5225

23282/20pk f5125

23283/10pk f5235

23284/20pk f5135

23328/20pk f5175

23336/20pk f5065

23375/20pk f5085

23376/20pk f5095

23377/20pk f5105

23379/20pk f5115

23418/20pk f5025

23492/10pk f6176

23492/20pk f5045

23566Sw f5730

23567Sw f5740

23580/20pk f5075

24566Sw f5810

24567Sw f5820

24-c f4872

24-cap f4830

24-f f4873

24-fap f4840

26571/20pk f5305

26578/20pk f5055

33569/20pk f5195

33571/20pk f5145

33575/20pk f5035

61119/10pk f6174

61126/10pk f6171

61129/10pk f6172

61130/10pk f6175

61131/10pk f6165

61132/10pk f6173

gw # wIn #

61142/10pk f6164

62112Sw f6090

62113Sw f5980

62114Sw f5990

62122Sw f5890

62123Sw f5900

62124Sw f5910

62125Sw f5920

62126Sw f5930

62127Sw f5940

21543Sw f5470

62135Sw f6000

62136Sw f6010

62137Sw f6020

62222Sw f5950

62223Sw f5960

62224Sw f5970

62225Sw f6100

62310Sw f6060

62320Sw f6070

62330Sw f6080

62425Sw f6030

62525Sw f6040

62723Sw f6120

62920Sw f6050

62a23Sw f6110

81567/20pk f5455

81569/20pk f5385

81570/20pk f5415

81571/20pk f5325

84572h/20pk f5355

84573/20pk f5275

87566/20pk f5435

87567/20pk f5445

87569/10pk f6170

87569/20pk f5475

87570/20pk f5405

87571/20pk f5315

87572/20pk f5345

87573/10pk f6168

87573h/20pk f5265

87575/20pk f5285

99-23 f3370

a-10 f5207

a-13 f4880

a-15 f6555

a-16 f6556

a-26 f4871

a-30 f4870

a-31 f4860

a-6 f4850

gw # wIn #

a-61-100 f4561

a-61-110 f4562

a-68 f4205

a-69 f4215

a-8 f6191

a80-10 f4570

a80-100 f4560

a80-15 f4055

b23569/20pk f5365

c10-23-01 f4930

c20-04 f4330

c20-04n f4340

c20-12 f4720

c20-20 f6157

c20-34 f4630

c20-36 f6190

c20-37 f4730

c20-55 f4320

c20-56 f6189

c20-58 f4450

c20-64 f4710

c20-69 f4400

c31-07 f4410

c31-100 f6549

c31-167 f4035

c31-32 f6548

c31-32/10pk f5165

c61-31 f4302

c6131t f4045

c61-32 f4301

c61-56 f6188

c6318-hw f5215

c74-01 f4370

c74-150 f4105

c74-150b f4156

c74-16 f4650

c74-28 f6187

c74-32 f6186

c74-44 f4740

c74-47 f4460

c74-50b f4550

c74-51 f4390

c74-52 f4380

c74-55 e4850

c74-55b f4760

c80-12 f6160

c80-14 f6159

c80-158 f4135

c80-15w f4065

c80-20 f6137

c80-41 f4360

gw # wIn #

c80-42 f4350

c80-43 f4300

c80-97 f6185

c88-06h f3494

c88-12t f6606

f6562 f6562

p10-12-01 f4059

p10-12-07 f4061

p10-14-01 f4067

p10-14-07 f4068

p10-15-08 f4062

p10-16-01 f4026

p10-17-01 f4027

p10-18-01 f4028

p10-18-06 f4063

p10-19-01 f4980

p10-20-01 f4150

p10-20-07 f6101

p10-21-01 f4170

p10-22-01 f4180

p10-22-07 f6102

p10-24-01 f4160

p10-25-01 f4190

p10-26-01 f4220

p10-27-01 f4940

p10-27-02 f4960

p10-27-03 f4950

p10-28-01 f4210

p10-29-01 f4200

p10-30-01 f6122

p20-07 f6130

p20-14 f4490

p20-15 f4790

p20-16 f4670

p20-17 f4590

p20-26 f4620

p20-35 f4440

p20-40 f4540

p20-41 f4640

p20-49 f4290

p20-50 f4780

p20-52 f4530

p20-68 f6124

p20-86 f6517

p20-87 f6518

p20-89 f6519

p20-90 f6520

p31-57 f4165

p61-08 f6125

p61-12 f6139

p61-16 f6128

gw # wIn #

p61-24 f6138

p61-29 f6129

p61-68 f4280

p74-10 f4580

p74-11 f6153

p74-14 f4500

p74-150 f4155

p74-19 f4680

p74-24 f6156

p74-25 f4610

p74-26 f4660

p74-31 f6151

p74-40 f4810

p74-43 f4310

p74-45 f4470

p74-48 f4270

p74-49 f4240

p74-50 f6149

p74-58 f4250

p74-59 f4230

p74-89 f6515

p74-90 f6516

p80-02 f6117

p80-06 f4800

p80-07 f4801

p80-105 f4441

p80-108 f4175

p80-110 f6182

p80-111 f6183

p80-112 f6184

p80-116 f4185

p80-120 f4195

p80-134 f4145

p80-147 f4032

p80-148 f4033

p80-15 f4770

p80-150 f4039

p80-157 f6214

p80-18 f4690

p80-46 f6142

p80-49 f4480

p80-50 f4820

p80-51 f4260

p80-52 f4520

p80-55 f4510

p80-57 f6152

p80-69 f6162

p80-70 f6145

p80-72 f6146

p80-73 f6148

p80-78 f6161

gw # wIn #

p80-81 f6511

p80-86 f6513

p80-87 f6514

p80-88 f6512

p80-98 f6147

p88-11 f4034

p88-19 f4031

p88-79 f4037

p88-98 f4038

p88-99 f4036

p96-75 f4071

p96-76 f4058

p96-77 f4066

pgw-56-a f4140

pgw-57-a f4130

pgw-58-a f4120

pgw-59-a f4110

pgw-60-a f4100

pgw-61-a f6121

pgw-75-a f4069

pgw-76-a f4057

pgw-77-a f4064

pgw-79-a f5203

pgw-80-a f6140

pgw-81-a f4970

pgw-82-a f4060

pgw-83-a f4050

pgw-84-a f4040

pgw-85-a f4030

pgw-86-a f4020

pgw-87-a f4010

pgw-88-a f4070

pgw-89-a f4080

pgw-90-a f4090

pgw-91-a f4890

pgw-92-a f4900

pgw-93-a f4910

pgw-94-a f4920

pgw-95-a f4115

pgw-96-a f5206

pgw-97-a f4125

pgw-98-a f5204

pgw-99-a f4972

t-12 f6558

t-16 f6559

t-20 f6560

t-24 f6561

t-6 f6585

chrome acorn Screw & nut kItS for SportSterwIn# deScrIptIonf6247 57-84 Cylinder Base Nut Kit f6308 57-84 Lifter Base Screw Kit f6259 86-up 883 1100 XL Lifter Base Screw Kit f6307 76-up 12 PNT Lifter Base Screws

f6259

fasteners

17-42

f6204

acorn Screw &nut kItS for bIg twInwIn# deScrIptIon f6213 78-84 Shovelhead Cylinder Base Nut Kit f6219 36-75 Big Twin Lifter Base Screw Kit O.H.V. f6306 76-up BT Lifter Base Screw Kit f6226 36-84 BT Motor Mount Kit Lower f6227 36-84 BT Motor Mount Kit Upperf6230 36-69 Primary Cover Screw Kit Use on Stamped Steel Inner & Outer

f6231 65-70 Big Twin Primary Cover Screw Kit Cast Aluminum Coverf6232 71-up Big Twin 4-Speed Primary Cover Screw Kit f6234 85-89 Big Twins 5-Speed Except 89 FXST Primary Cover Screw Kit f6235 89 FXST Primary Cover Screw Kit f6237 66-84 Shovelhead Rocker Box Nut Kit f6239 71-up Big Twins Timing Cover Screw Kit f6242 87-up FX, FL Transmission Side Cover Screw Kit

chrome plated acorn nutSwIn# thread SIZe qty.

f6200 1/4 - 24 h-d 5

f6201 10 - 32 Sae 5

f6202 1/4 - 28 Sae 5

f6203 5/16 - 24 Sae 4

f6204 3/8 - 24 Sae 3

f6205 7/16 - 20 Sae 2

f6206 1/2 - 20 Sae 1

f6207 9/16 - 18 Sae 1

f6208 5/8 - 18 Sae 15/16 1

f6209 3/4 - 16 Sae 1-1/8 1

f6210 5/8 - 18 Sae 1-1/4 1

gardner weStcot cabInetS & trayS f6585 6 Tray empty cabinetf6562 6 Tray cabinet with the following trays 2 - 12 compartment trays 1 - 16 compartment tray 1 - 20 compartment tray 2 - 24 compartment trays

trayS Sold eachf6558 12 compartment trayf6559 16 compartment trayf6560 20 compartment trayf6561 24 compartment tray

f6585 f6562

17-43

fastener accessories

chrome Skull krommetSIf you want your bike honed to the finest detail, then these are for you. Krommets come complete with rhinestone eyes. 10 packk3600 Krommets

chrome Snap capSThese snap caps feature a two piece design and are available in three sizes. 10 pack f2226 1/4 #6f2227 5/16 #8f2228 3/8 #10

reInforced rubber waSherSThe answer to mechanical vibrations. Made of 1/8 thick reinforced neoprene rubber. Ideal for thin panels, fenders, license plates, air cleaner lids and a host of other items than benefit from rubber mounting. 10 packm9010 1/4 hole m9020 5/16 hole

kryakyn Star capSThese unique Star Caps can be used for a variety of applications, adding real pizzazz to license plate mounts, fenders and lots of unexpected places. Each includes a 6mm stud, nut and washer. They install with ease for a super-custom look on any bike. Their low draw means a long worry-free life.t3530 Chrome with red lensest3531 Chrome with amber lensest3532 Chrome with blue lenses

oIl dIpStIck abSorbent matMade from the same material used to clean major oil spills. The thirsty material is specially treated to soak up 10 times its weight in oil and oil related products. It can be used over and over again. To clean simply wash with warm water and mild detergent. Once clean, squeegee out excess water and let air-dry.o3442 Dipstick rag

bullet style harDWare

17-44

#1 wIth a bulletWins Bullet Style Stainless Steel Hardware is here! This complete line looks fantastic and

features American made quality and craftsmanship. Highly polished to a mirror finish, Bullet Style Stainless Steel Hardware will turn heads wherever you cruise. These are the type of

parts that add that subtle distinction that can mean the difference between a #1 show bike or a long ride home.

StaInleSS Steel rearfender Strut hardware f6407 Bolt, nut, washer kit for Softail

StaInleSS Steel front aXle nut & Spacer Setf6404 All Softail except Springer

StaInleSS Steel aXle & nut aSSemblIeS f6405 FXSTS Springer front axle f6406 Rear axle & spacer, washer set for Softail

StaInleSS Steel front fender bolt SetS f6411 84-90 Softail

17-45

bullet style harDWare

StaInleSS Steel SwIngarm pIvot bolt Setf6403 Softail models

StaInleSS Steelbullet head boltSFits outer only. We recommend that this product be installed by a qualified mechanic. Removing & installing these will shift head torque to inner bolts.Set of four.f6401 EVO Big Twin, EVO XL & Twin Cam models

StaInleSS SteelrISer bolt & waSher kItf6402 Dyna Glide, Wide Glide & Custom Softail

tie DoWns

17-46

t9160 5 6 x 1 1/2 black with orange 3/8 straight hook, thumb release buckle, pair.t9170 5 6 x 1 black with orange 3/8 straight hook, ratchet buckle, each.t9180 21 x 1 black tie down assist pairt9190 21 x 1 orange tie down assist pair

tIe downS & tIe down aSSIStSMade In America of strong 4,000 lb. test nylon webbing these one inch tie downs are the highest quality

available for every usage. All sews are made of strong nylon thread. The hook is covered with vinyl plastic to protect paint and chrome. Handy American Made 4,000 lb. test nylon assists are easy to use

and have many applications.

heavy-duty tIe downSThese ultra tough tie downs are made of super strong 3500 lb. test nylon webbing which is double stitched for added durability. This is the popular thumb release type. All hardware is made by ANCRA so you know its the best.t9200 7 X 1, pair

bungee cordSt9010 14 2 hook t9020 18 2 hookt9030 24 2 hook t9040 30 2 hook

t9160

t9190

t9180

t9170

17-47

Paints & cleaners

a. b. c.

f. g. h.

d. e.

a. gloSS black engIne paIntEasy to apply, this chip resistant paint bonds tight and protects against rust.c1001 11oz. can sold eachc1000 6/Case

b. flat black hI-temp paIntThe ultimate heat resisting paint, it protects to 1400 on exhaust and other high-temperature applications. Flat finish resists chips and rust.c1002 11oz. can sold eachc1140 6/Case

c. SatIn black caSe paIntThis semi-gloss finish is perfect for restoring engine and drive train components like new. Protects to 500 against chipping and corrosion.c1003 11oz. can sold eachc1150 6/Case

d. hIgh gloSS epoXy fInIShThis extra durable epoxy wet look finish is perfect for high wear areas that require the ultimate in chip resistant protection.c1004 11oz. can sold eachc1160 6/Case

e. wrInkle teXture coatOffering a durable, corrosion proof finish, this 500 wrinkle finish actually dissipates heat while covering scratches and chips.c1005 11oz. can sold eachc1170 6/Case

f. pro contact cleanerThis professional power spray removes contaminants from all electrical components. Wont harm rubber, plastic, painted materials or contaminate motor oils. Quick drying with no chlorinated solvents.c1006 19.7 oz. can sold eachc1020 6/Case

g. Super contact cleanerCan be used to clean, degrease and displace moisture on all metal parts. Also removes adhesives and grease spots from floors and fabric. Safe on most plastics and paint.c1007 13 oz. can sold eachc1120 6/Case

h. foam fIlter treatmentA super tacky formulation for high performance engines that filters grit and sand from engine air. It repels water and resists pooling. Propellant is ozone safe.c1008 13 oz. can sold eachc1010 6/Case

lubes & cleaners

17-48

a. b.

c. d.

e. f.

a. black label heavy duty chaIn lubeAll-purpose chain lube excellent for street, touring & off-road applications. Thick, tacky formula eliminates messy fly off and stops chain rust.c1009 6 oz. can sold eachc1060 12/casec1011 13 oz. can sold eachc1070 6/case

b. blue label chaIn lubeKeeps O-ring chains lubricated and pliable and adds life to O-ring chain. Wont fly off.c1012 5 oz. can sold eachc1080 12/casec1013 13 oz. can sold eachc1090 6/case

c. Spray & waShEasy to use deep-penetrating grease remover cleans oil and dirt with no ugly residue. Simply spray it on & hose it off.c1014 15 oz. can sold eachc1130 6/case

d. octane pluS gaS energIZerThis EPA approved power boost contains racing fuel to increase speed. It protects valve seat wear due to low-lead gasoline and reduces carburetor and intake valve deposits.c1015 Liter can sold eachc1050 6/case

e. renew & protectRenews & protects all rubber, plastic, vinyl and fine leather with a new super silicone moisturizing formula. Contains no damaging plasticizers or petroleum distillates.c1016 8 oz. can sold eachc1100 12/casec1017 1 Pint can sold eachc1110 12/case

f. fork oIlFork Tuner fork oil features consistent, smooth damping action for all seasons. This non-fading, non-foaming formula allows you to fine tune your ride to personal preference and contains a preservative to prevent seal leaks. 1 liter bottles available each or by the case of 6.

10wt 15wt 20wt 30wtc1032 c1033 c1018 c1019 eachc1029 c1031 c1030 c1040 6/caSe

17-49

lubes & cleaners

a. b. c.

d.

g.

f.

h.

e.

a. Spray fabrIc fIlter oIlFilters out dirt & sand, repels water and makes engine breathe more efficiently. For gauze type air filters.c1161 15 oz. can sold eachc1171 6/case

b. penetrant/lubrIcantLubricates all metal and moving parts with superior lubricating properties. Penetrates to unlock frozen threads while preventing rust and corrosion.c1162 11 oz. can sold eachc1172 6/case

c. foam fIlter cleanerQuickly dissolves dirt and grime with a simple spray on and hose off method. Wont harm filter glues.c1163 15 oz. can sold eachc1173 6/case

d. pro brake cleanerEnvironmentally safe formula and power propellant to clean and degrease contaminates from brake units. Increases performance. Contains no chlorinated solvents and wont contaminate oils.c1165 19.7 oz. can sold eachc1175 6/case

e. engIne aSSembly lubeProtects critical engine and transmission parts while reducing friction and providing the ultimate edge in lubricating requirements. Spray formula gets those hard to reach areas.c1166 11 oz. can sold eachc1177 6/case

f. pJ-1 motor oIlCooler running for reduced engine wear and provides smoother shifting to extend clutch and transmission life.c1023 10W40 Synthetic 1 Literc1021 6/case Syntheticc1024 20W50 Synthetic 1 Literc1022 6/case Syntheticc1041 20W50 1 Literc1042 6/case

g. pJ-1 tranSmISSIon oIlPJ-1s Hypoid Drive Shaft Oil quiets rear end noise, withstands extreme temperatures and is non-foaming.c1027 90wt 1 Literc1025 6/case h. hI-temp brake fluIdOur new brake fluid from Russell is hightemperature rated, D.O.T. 5 and sold each.c1034 Brake fluid

miscellaneous aPPlications

17-50

thread lock by threebondHi Temp. Thread Lock is made to withstand extreme temperature. It incorporates the various strengths of anaerobic locking agents and is capable of withstanding 392F. ThreeBonds Low Strength Frequent Repair product is perfect for small screws & bolts which are frequently removed, and require a force only 10-20% greater than that used for tightening.

Super glue by threebondA cyanoacrylate based instant high strength adhesive of the solventless single liquid type. Attains practical use strength in a matter of seconds. Never any shrinkage to weaken bonding points. Excellent for nonporous materials including rubber, metal, plastic and glass.c1410 Super Glue

Super glue gel by threebondA thixotropic gel with many of the same properties as C1410, but is suitable for large clearance areas and porous materials such as leather. When applied, the gel stays in place and will not run.c1469 Super Glue Gel

plaStIc thread lockerby threebondNow there is a thread lock safe for all plastic and painted applications such as taillights, fairings, plastic and small screws. A synthetic rubber resin which prevents screws, nuts and bolts from coming loose, leaking or rusting. Every shop needs it.c1465 Clear 200mgc1466 Green 200mgc1467 Red 200mg

c1440 Hi Strength, orange 10 ml.c1441 Hi Strength, orange 50 ml.c1442 Hi Strength, orange 250 ml.c1450 Low Strength blue 10 ml.c1451 Low Strength blue 50 ml.c1452 Low Strength blue 250 ml.

c1420 Med. Strength, red 10 ml.c1421 Med. Strength, red 50 ml.c1422 Med. Strength, red 250 ml.c1430 Med. Strength Hi Temp. green 10 ml.c1431 Med. Strength Hi Temp. green 50 ml.c1432 Med. Strength Hi Temp. green 250 ml.

17-51

miscellaneous aPPlications

grIplock by threebondA high strength adhesive specially formulated to keep grips in place without damaging the rubber. Griplock puts an end to twisting or sliding grips. Ideal for all Harley.c1468 Griplock

SIlver SIlIcone lIquId gaSket by threebondA one component, non-slumping paste, RTV silicone rubber which begins to set up in minutes. C1463 possesses superior pressure resistance just after application and assembly. Perfect for sealing complex three-point surfaces of cylinder blocks, oil pans, valve covers and joint surfaces with large clearances to prevent oil, water, gasoline and chemical leaks. Effective temperature range -76 to 482 F -60 to 250C. Tack free time 5 minutes; fully cured in 24 hours.c1463 Liquid gasket silver

whIte SIlIcone lIquId gaSket by threebondA free flowing, low viscosity, one component RTV silicone rubber. C1461 is ideal for places where a long faultless seal is absolutely critical. Recommended for sealing flange surfaces and screw sections to prevent oil, water, gasoline and chemical leaks. Effective from -76 to 482F -60 to 250C. Tack free in 90 minutes, fully cured in 24 hours.c1461 Liquid gasket white

cleaners

17-52

pIg SpIt engIne ShInethe beSt on the market!Specially developed for treating black wrinkle paint on Harley Engines. Also works great on mags, dashes, brake calipers and other wrinkle finish parts. Silicone based product will not attract dust or harm paint. Great for removing wax marks on black wrinkle paint.c1521 Pig Spit Engine Shine, 9 oz. can 12/Case c1522 Pig Spit Engine Shine, 9 oz. can Each

engIne gloSS by threebondA unique acrylic formula that protects external parts and helps keep surfaces clean. Protects external engine, running gear components, brushed aluminum and chrome from all types of corrosion and dirt. Use of a good degreaser is recommended prior to application.c1462 Detail engine gloss

blue-Job eXhauSt pIpe cleanerWorlds best chrome polish, chrome exhaust pipe de-bluer and rust remover.c1184 Blue Job 12/pack with P.O.P. displayc1185 Blue Job Sold each

blue-Job eXhauSt pIpe wIpeSYou asked for it, so we super sized the BLUE-JOB chrome polish cloth and packaged it separately. Use it with BLUE-JOB chrome polish for extreme shine. c1187 Blue Job Pipe Wipes 36/pack with P.O.P display c1186 Blue Job Pipe Wipes case with 4-36/pack with P.O.P display

no Scratch chrome cloth BLUE-JOB Pipe Wipes do not contain polishing compound Trust no other cloth on your precious chrome, gemstones, diamonds, and fine crystal. The BLUE-JOB Pipe Wipes finishing cloth will never scratch, swirl or dull chrome. BLUE-JOB Pipe Wipes polish support micro fibers give you the worlds finest polishing technology period. Once used with BLUE-JOB chrome polish, they become a magic fine chrome polishing cloth lasting a long time. Store clean in the resealable package.

17-53

Seal n aIr by threebondAerosol can inflates tire to moderate pressure in only 20 seconds. When you resume riding, the white foaming fluid spreads evenly inside the tire & seals the leak. Tire pressure also increases gradually while riding. Not effective for large holes or sidewall punctures. Works on tubed & tubeless tiresc1400 ThreeBond Seal n Air

aSSembly lubrIcantCamshaft assembly lube is a moly disulfide base lubricant for unequal wear protection. It is recommended for gears, bearings, bushings, pushrod tips and much more.e6650 2 oz. container

SlIcker n Snot lubrIcant by roweAmerican made assembly lubricant works great on all parts that reciprocate, rotate, roll, slide, turn, push or shove! c1485 12/Casec1473 1 oz. bottle sold each

seal & lubricants

SlIme tubeFlat tire eliminator. Slime works to bind the damaged rubber & create a clot in the punctured area.t3890 400, 450 X 18t3940 325, 350 X 19

17-54

k & n lubes & cleaners

k&n fIlter charger oIlK&N Air Filter Oil is the only oil specially formulated to work in combination with the cotton fabric in K&N Filtercharger elements providing a superior air filtration system. When used as directed, it quickly penetrates the filter pleats, where it remains suspended in the cotton fabric. Saturation is maintained until the element is cleaned with K&N Air Filter Cleaner.c1035 6 -oz aerosol can c1036 12-oz aerosol can

k&n fIlter cleanerThe only cleaner formulated to clean K&N Filtercharger elements. The use of any other cleaning solution will void the filters warranty and possibly damage the cotton material. Works to dissolve the dirt build up and old filter oil, and can be washed away with water. It is biodegradable and safe on paint, chrome, cast aluminum, plastic, rubber and vinyl when used as directed. Do not use on polished or anodized aluminum.c1037 12-oz squirt bottle c1038 32-oz squirt bottle

Dont riDe off Without us.