GB - 35

ENGINE AND BELT DRIVE

Model 926001, 002, 003, 004, 005, 006, 101, 102, 103, 300, 301, 302, 303, 304, 500, 501, 502, 504

PS1082

2

34

6

7 811

12

10

13

15

16

1718

1921

4

22

9

23

24

26

1

22

3420

31 32

29

2230

28

33

353637

39

38

40

4141

GB - 36

Model 926007, 008, 009, 010, 011, 012

PS1082

2

4

6

7 811

12

10

13

15

16

1718

1921

4

22

9

23

25

27

1

22

3420

31 32

29

2230

28

33

3536

37

39

38

40

4141

1243

42

44

45

GB - 37

ENGINE AND BELT DRIVE

Model AllItem Part No. Qty. Description

1 06529200 3 Nut, Hex .31-18 (500, 501)06529200 4 Nut, Hex .31-18

2 06307400 3 Washer, Lock .312 x .097 (500, 501)06307400 4 Washer, Lock .312 x .097

3 08200038 1 Engine, 9.25HP Tecumseh LH318SA - 156582H - 120 Volt (001, 101)08200039 1 Engine, 9.25HP Tecumseh LH318SA - 156581H - 240 Volt (504) 08200040 1 Engine, 9.25HP OHV Tecumseh OH318SA - 221825B - 120 Volt (004)08200041 1 Engine, 9.25HP OHV Tecumseh OH318SA - 221827B - 240 Volt (301)08200043 1 Engine, 11.5HP OHV Tecumseh OH318SA - 221828B - 120 Volt (002, 005, 102)08200044 1 Engine, 11.5HP OHV Tecumseh OH318SA - 221826B - 240 Volt (300, 304)08200045 1 Engine, 13HP Tecumseh OHV OH358SA - 223842F - 120 Volt (003, 006, 103)08200046 1 Engine, 13HP Tecumseh OHV OH358SA - 223841F - 240 Volt (302, 303)08200047 1 Engine, 13HP Tecumseh OHV OH358SA - 223843F - 12 Volt (500, 501)08200042 1 Engine, 9HP Tecumseh OHV OH318EA - 222719E - (502)

4 08200112 1 Engine, 9.5hp Briggs & Stratton, Powerbuilt 20A1140120E1, 120V (007)08200113 1 Engine, 9.5hp Briggs & Stratton, Intek 20B4140121E1, 120V (008)08200114 1 Engine, 11.5hp Briggs & Stratton, Intek 21C3140116E1, 120V (009, 010)08200015 1 Engine, 13.0hp Briggs & Stratton, Intek 21B4140117E1, 120V (011, 012)

5 00461900 1 Belt Finger6 05947300 2 Bolt, Hex .31-24 x .75 Grade 57 00397100 1 Sheave, Drive8 00397000 1 Sheave, Attachment9 00384100 1 Cover, Belt10 07200020 1 V-Belt 4L 37.06 (001, 002, 004, 005, 007, 008, 009, 010, 011, 012, 101, 102, 300, 301, 304, 502, 504)

07200021 1 V-Belt 4L 38.00 (003, 006, 103, 302, 303, 500, 501)11 52602100 1 Plate, Swing Assembly 12 07200101 1 V-Belt,Traction Drive (001, 002, 004, 005, 007, 008, 009, 010, 011, 012, 101, 102, 300, 301, 304, 502,

504)07200102 1 V-Belt, Traction Drive (003, 006, 103, 302, 303, 500, 501)

13 52601800 1 Arm, Brake Attachment with Pad14 00180500 1 Pad, Brake15 08300017 1 Spring, Tension .056 x .60 x 4.4016 06542000 1 Nut, Locking Top Flange .38-1617 07300013 1 Idler, Flat 3.0018 05957900 1 Bolt, Hex .38-16 x 1.50 Grade 519 05947500 1 Bolt, Hex .31-18 x 1.25 Grade 520 01213100 1 Spacer, Bearing21 02457400 1 Idler22 07412000 4 Screw, Tapping .25-20 x .50 Hex Washer Head Thread Rolling23 02483100 1 Cord, Extension 110V24 21533500 1 Plug, Spark25 21534100 1 Plug, Spark26 07532000 1 Key, Push/Pull Tecumseh (001, 002, 004, 005, 007 ,101, 102, 300, 301, 304, 500, 501)27 07500012 1 Key, Push/Pull Briggs & Stratton (007, 008, 009, 010, 011, 012)28 00430751 1 Pivot, Brake29 05957200 1 Bolt, Hex .31-18 x 2.00 Grade 530 06543100 1 Nut, Locking-Top-Flange .31-1831 06308800 1 Washer, Locking .38 x .09432 05958600 1 Bolt, Hex .38-24 x 2.033 06307400 2 Washer, Locking .312 x .097 Heavy 34 06543100 1 Nut, Locking-Top-Flange .31-1835 06310500 1 Washer, Lock Internal .31 (500, 501)36 06437200 1 Washer, Flat-Steel .344 x .688 x .065 (500, 501)37 06529800 1 Nut, Locking-Center .31-18 (500, 501)38 08300019 1 Spring, Tension .048 x .50 x 2.839 00380900 1 Rod, Housing Pivot40 06436200 1 Washer, Flat Steel .406 x .812 x .065 (001, 002, 004, 005, 007 ,101, 102, 300, 301, 304, 500, 501)41 06714800 3 Pin, Hair42 06443000 1 Washer, Flat, Steel 1.062 x 2.0 x .134 (007, 008, 009, 010, 011, 012)43 06435700 1 Washer, Flat Steel .38 x .875 x .083 (007, 008, 009, 010, 011, 012)44 07500013 1 Gas cap (007, 008, 009, 010, 011, 012)45 00486451 1 Guard, Belt Cover, Briggs & Stratton (007, 008, 009, 010, 011, 012)

GB - 38

WHEELS AND AXLEThe wheels are held onto the axle with locking pins. To remove a wheel pull the locking pin and the wheel will slideoff. To remove the axle:

1. Place the unit in upright service position.20.Remove the bottom plate.21.Remove both wheels.22.Drive out roll pin.23.The axle will slide out either side.

NOTE: Make a record of the positions for the washers and flanges for reassembly.To install the axle:

1. Slide the axle into the main frame from either direction.24.Place bearings, washers, and spur gear into the axle in correct order.

NOTE: The spur gear can go on in either way. The nylon flanges must enter into the bushings from the inside out.25.Insert the woodruff key into the axle and slide the spur gear into position.26.Move washers into position and drive the roll pins into the axle27.Replace wheels.

SPROCKET AND CHAINA friction wheel is driven and provides power to the axle shaft. Power is transferred using a chain to a sprocketassembly. To replace the drive chain remove both shafts. To remove pinion shaft:

1. Place unit in up right service position.28.Remove wheels and bottom plate.29.Drive out the two roll pins. These two pins are different in diameter. Make note of which pin is in each hole.30.Slide the shaft out towards the end with the grease fitting.

NOTE: The components on the pinion shaft can all be removed. The hex shaft must be removed (at least partially)to remove the roller chain. To remove the hex shaft:

(see Friction Disc Replacement on page 30).To install pinion shaft:

1. Slide pinion shaft into the main body with the roll pin hole closest to the end away from the pinion. 31.Put the washer, flange, and pinion over the shaft. The shaft should be through the center of the chain.32.Position the shaft with pinion and other parts in place.33.Select the correct roll pin for the hole on the shaft and drive it into position. 34.Drive the second roll pin into the shaft.35.Grease the pinion using the grease fitting on the end of the shaft.

WHEELS, AXLE AND REDUCTION DRIVE