ENetwork Basic Configuration PT Practice SBA A few things to keep in mind while completing this activity:

1. Do not use the browser Back button or close or reload any Exam windows during the exam. 2. Do not close Packet Tracer when you are done. It will close automatically. 3. Click the Submit Assessment button to submit your work.

Introduction In this practice Packet Tracer Skills Exam, you will:

• finish connecting the devices • design and implement an addressing scheme to meet stated requirements • configure, verify, and troubleshoot connectivity between all devices in the network

Addressing Table

Device Interface Address Subnet Mask Default Gateway

Router1 Fa0/0 172.16.1.1 255.255.255.224 n/a

Fa0/1 172.16.1.33 255.255.255.240 n/a

Switch1 VLAN1 172.16.1.2 255.255.255.224 172.16.1.1

PC1 NIC 172.16.1.30 255.255.255.224 172.16.1.1

PC2 NIC 172.16.1.46 255.255.255.240 172.16.1.33

NOTE: The initial network has some errors. To aid in configuring and verifying the devices as well troubleshooting the existing errors, use a printed version of these instructions to fill in the missing address information in the table during Step 2.

Step 1: Connect the Devices. Connect the following devices using the appropriate cable:

a. Connect PC1 to Switch1.

b. Connect Switch1 to the Fa0/0 interface on Router1.

c. Connect Switch2 to the Fa0/1 interface on Router1.

d. Connect PC1 to the Router1 console port.

Step 2: Determine the IP Addressing Scheme. Design an addressing scheme and fill in the Addressing Table based on the following requirements:

a. Subnet the address space 172.16.1.0/24 to provide 30 host addresses for LAN 1 while wasting the least amount of address space.

b. Assign the first available subnet to LAN 1.

c. Assign the lowest (first) host address in this subnet to the Fa0/0 interface on Router1.

d. Assign the second address in this subnet to the VLAN 1 interface on Switch1.

e. Assign the highest (last) host IP address in this subnet to PC1.

f. Using the next available subnet, further subnet it to provide 10 host addresses for LAN2 while wasting the least amount of address space.

g. Assign the lowest (first) host address in the LAN2 subnet to the Fa0/1 interface on Router1.

Step 3: Configure Router1. a. Configure Router1 with the following basic parameters:

• The router name is Router1.

• The privileged EXEC mode uses the following encrypted password: class

• Enable Telnet and console line login using the following password: cisco

• Configure the banner message-of-the-day as Authorized access only!

b. Configure the two Fast Ethernet interfaces, including addressing and a description.

c. Close the terminal window after completing the router configuration.

Step 4: Configure Switch1 and Verify Connectivity. a. Remove the console connection between PC1 and Router1.

b. Connect PC1 to the Switch1 console port.

c. Configure Switch1 with the following basic parameters:

• The switch name is Switch1

• The privileged EXEC mode uses the following encrypted password: class

• Enable Telnet and console line login using the following password: cisco

• Configure the banner message-of-the-day as Authorized access only!

d. Configure interface VLAN 1 and default gateway for Switch1.

e. Switch1 should be able to ping the default gateway.

Step 5: Configure and Verify PC1 Addressing. a. Using the IP addressing you determined in Step 2, configure PC1 with the correct addressing.

b. PC1 should be able to ping the default gateway.

Step 6: Verify and Troubleshoot End-to-End Connectivity. Verify that PC1 is able to ping PC2. If the ping fails, locate and correct any errors. For example, make sure PC2 is configured correctly with appropriate addressing for the subnet it belongs to.

Version 1.0 Created in Packet Tracer 5.2.1 and Marvel 1.0.1 All contents are Copyright © 1992 - 2010 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.  

 

 

 

 

 

 

Activity Topology and Instructions

In this section, the initial topology and instructions are shown for review purposes.

Topology

Instructions

ENetwork Basic Configuration PT Practice SBA

A few things to keep in mind while completing this activity:

1. Do not use the browser Back button or close or reload any Exam windows during the exam. 2. Do not close Packet Tracer when you are done. It will close automatically. 3. Click the Submit Assessment button to submit your work.

Introduction

In this practice Packet Tracer Skills Exam, you will:  

• finish connecting the devices • design and implement an addressing scheme to meet stated requirements • configure, verify, and troubleshoot connectivity between all devices in the network

Addressing Table

Device Interface Address Subnet Mask Default Gatewa

Router1 Fa0/0     n/a Fa0/1     n/a

Switch1 VLAN1       PC1 NIC       PC2 NIC      

NOTE: The initial network has some errors. To aid in configuring and verifying the devices as well troubleshooting the existing errors, use a printed version of these instructions to fill in the missing address information in the table during Step 2.

Step 1: Connect the Devices.

Connect the following devices using the appropriate cable:

a. Connect PC1 to Switch1.

b. Connect Switch1 to the Fa0/0 interface on Router1.

c. Connect Switch2 to the Fa0/1 interface on Router1.

d. Connect PC1 to the Router1 console port.

Step 2: Determine the IP Addressing Scheme.

Design an addressing scheme and fill in the Addressing Table based on the following requirements:

a. Subnet the address space 172.16.1.0/24 to provide 30 host addresses for LAN 1 while wasting the least amount of address space.

b. Assign the first available subnet to LAN 1.

c. Assign the lowest (first) host address in this subnet to the Fa0/0 interface on Router1.

d. Assign the second address in this subnet to the VLAN 1 interface on Switch1.

e. Assign the highest (last) host IP address in this subnet to PC1.

f. Using the next available subnet, further subnet it to provide 10 host addresses for LAN2 while wasting the least amount of address space.

g. Assign the lowest (first) host address in the LAN2 subnet to the Fa0/1 interface on Router1.

Step 3: Configure Router1.

a. Configure Router1 with the following basic parameters:

⎬ The router name is Router1.

⎬ The privileged EXEC mode uses the following encrypted password: class

⎬ Enable Telnet and console line login using the following password: cisco

⎬ Configure the banner message-of-the-day as Authorized access only!

b. Configure the two Fast Ethernet interfaces, including addressing and a description.

c. Close the terminal window after completing the router configuration.

Step 4: Configure Switch1 and Verify Connectivity.

a. Remove the console connection between PC1 and Router1.

b. Connect PC1 to the Switch1 console port.

c. Configure Switch1 with the following basic parameters:

⎬ The switch name is Switch1

⎬ The privileged EXEC mode uses the following encrypted password: class

⎬ Enable Telnet and console line login using the following password: cisco

⎬ Configure the banner message-of-the-day as Authorized access only!

d. Configure interface VLAN 1 and default gateway for Switch1.

e. Switch1 should be able to ping the default gateway.

Step 5: Configure and Verify PC1 Addressing.

a. Using the IP addressing you determined in Step 2, configure PC1 with the correct addressing.

b. PC1 should be able to ping the default gateway.

Step 6: Verify and Troubleshoot End-to-End Connectivity.

Verify that PC1 is able to ping PC2. If the ping fails, locate and correct any errors. For example, make sure PC2 is configured correctly with appropriate addressing for the subnet it belongs to.

  

Version 1.0 Created in Packet Tracer 5.2.1 and Marvel 1.0.1 

All contents are Copyright � 1992 - 2010 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. �

Proposed Solution

Answer Topology

Answer Scripts

Router1

show run

Building configuration... Current configuration : 838 bytes ! version 12.4 no service timestamps log datetime msec no service timestamps debug datetime msec no service password-encryption ! hostname Router1

! ! ! enable secret 5 $1$mERr$9cTjUIEqNGurQiFU.ZeCi1 ! ! ! ! ! ! ! ! ip ssh version 1 ! ! ! ! ! ! interface FastEthernet0/0 description LAN 1 ip address 172.16.1.1 255.255.255.224 duplex auto speed auto ! interface FastEthernet0/1 description LAN 2 ip address 172.16.1.33 255.255.255.240 duplex auto speed auto ! interface Serial0/0/0 no ip address shutdown ! interface Serial0/0/1 no ip address shutdown ! interface Vlan1 no ip address shutdown ! ip classless ! ! ! ! ! banner motd ^CAUTHORIZED ACCESS ONLY^C ! ! ! ! logging trap debugging line con 0 password cisco login line vty 0 4 password cisco login

line vty 5 15 password cisco login ! ! ntp update-calendar ! end

Switch1

show run

Building configuration... Current configuration : 1247 bytes ! version 12.2 no service timestamps log datetime msec no service timestamps debug datetime msec no service password-encryption ! hostname Switch1 ! enable secret 5 $1$mERr$9cTjUIEqNGurQiFU.ZeCi1 ! ! ! interface FastEthernet0/1 ! interface FastEthernet0/2 ! interface FastEthernet0/3 ! interface FastEthernet0/4 ! interface FastEthernet0/5 ! interface FastEthernet0/6 ! interface FastEthernet0/7 ! interface FastEthernet0/8 ! interface FastEthernet0/9 ! interface FastEthernet0/10 ! interface FastEthernet0/11 ! interface FastEthernet0/12 ! interface FastEthernet0/13 ! interface FastEthernet0/14 ! interface FastEthernet0/15 ! interface FastEthernet0/16

! interface FastEthernet0/17 ! interface FastEthernet0/18 ! interface FastEthernet0/19 ! interface FastEthernet0/20 ! interface FastEthernet0/21 ! interface FastEthernet0/22 ! interface FastEthernet0/23 ! interface FastEthernet0/24 ! interface GigabitEthernet1/1 ! interface GigabitEthernet1/2 ! interface Vlan1 description VLAN1 address ip address 172.16.1.2 255.255.255.224 ! ip default-gateway 172.16.1.1 ! banner motd ^CAUTHORIZED ACCESS ONLY^C logging trap debugging ! line con 0 password cisco login ! line vty 0 4 password cisco login line vty 5 15 password cisco login ! ! end

Switch2

show run

Building configuration... Current configuration : 1081 bytes ! version 12.1 no service timestamps log datetime msec no service timestamps debug datetime msec no service password-encryption ! hostname Switch2 !

! ! interface FastEthernet0/1 ! interface FastEthernet0/2 ! interface FastEthernet0/3 ! interface FastEthernet0/4 ! interface FastEthernet0/5 ! interface FastEthernet0/6 ! interface FastEthernet0/7 ! interface FastEthernet0/8 ! interface FastEthernet0/9 ! interface FastEthernet0/10 ! interface FastEthernet0/11 ! interface FastEthernet0/12 ! interface FastEthernet0/13 ! interface FastEthernet0/14 ! interface FastEthernet0/15 ! interface FastEthernet0/16 ! interface FastEthernet0/17 ! interface FastEthernet0/18 ! interface FastEthernet0/19 ! interface FastEthernet0/20 ! interface FastEthernet0/21 ! interface FastEthernet0/22 ! interface FastEthernet0/23 ! interface FastEthernet0/24 ! interface GigabitEthernet1/1 ! interface GigabitEthernet1/2 ! interface Vlan1 ip address 172.16.1.34 255.255.255.240 ! ip default-gateway 172.16.1.33 ! logging trap debugging !

line con 0 ! line vty 0 4 login line vty 5 15 login ! ! end

Terminology

Performance Component - a description of what the student knows and can do about a coherent set of networking knowledge and skills; the level at which the student's work product can be assigned a proficiency estimate.

Proficiency Estimate - a description of a student's level of mastery of the performance component. The proficiency estimate is not meant to be a comprehensive statement of what the student knows and can do.

Work Product - student performance recorded during this assessment. For example, the submitted activity file, timing statistics, and final running configurations.

Work Product Feature - An aspect of the student's work product. The feature can have a name and a value. For example, Name = FastEthernet0/0:IP Address; Value = 192.168.1.1

Individual work product features are combined into performance components and scored based on the complexity of the performance observed. Because the construction of performance components is based on the underlying work product features as well as the unique design of each scenario, strict boundaries for determining a proficiency rating are not possible. In general:

• None - 0% to 25% of possible points • Novice - 26% to 50% of possible points • Partial - 51% to 85% of possible points • Proficient - 86% to 100% of possible points