ENCORE™ DYADOPERATOR (SILL MOUNT)

26l

SEE FIG 2

SEE FIG 2

SEE FIG 2

SEE FIG 2

MAXMIN

3

3

3

2

3

MAXMIN

[330.2 mm]13.000

SASH AT 90° WITH14.97 WASHABILITYHINGE

[125.4 mm]4.938

25.4 mm6.3 mm

1.000.250

[203.2 mm]8.000

[44.5 mm]1.750

[6.3 mm].250

[135.4 mm]5.330

[12.7 mm].500 MAX

[30.2 mm]1.188

[17.1 mm].675 MIN

[9.0 mm].35354.0 mm

41.3 mm

2.1251.625

[10.7 mm].420 MAX

[20.6 mm].810

[15.1 mm].595 MIN

[2.0 mm].080

[125.9 mm]4.955 MIN

[2.4 mm]4X R.094

[125.9 mm]4.955 MIN

[2.4 mm]2X R.094

FRAME

SASH

FRAME

SEE FIG 2

SILLFILLER

SILLFILLER

OPERATOR CUT-OUT(WOOD)

OPERATOR CUT-OUT(PVC)

MIN."A"

LEFT HAND SHOWN

APPROXIMATE MINIMUMCOMPONENT WIDTH

BASEMOUNTINGFLANGE

BELOWOPERATOR

REQUIRED FORBOTTOM SEAL

SEE FIG.2 FOR BILL OF MATERIAL AND NOTES

SASH

FIG. 1 APPLICATION OF ENCORE DYAD OPERATOR(SILL MOUNT VERSION)

ENCORE™ DYADOPERATOR (SILL MOUNT)

26m

12511.XX STUD BRACKET

50.60.00.011

14.97.00.XXX

12616.XX

32658

DYAD OPERATOR

WASHABILITY HINGE

TANGO HANDLE/COVER PACK

GASKET (PVC)

SASH

FRAME

HARDWARE SHOWN FOR LEFT HAND WINDOW, SEE FIG. 1

DESCRIPTION PART NUMBER

14.12.00.XXX

HINGE "A"

14.97.00.XXX .300 [7.6 mm]

.250 [6.4 mm]

[10.7 mm] .420

[1.6 mm] .062

12511.XX BRACKET PLACEMENT

OTHER 14 SERIES CASEMENT HINGE

NOTES:

1. STUD BRACKET 12510.XX AND 12511.XX REQUIRES THE SAME MOUNTING LOCATION FOR BOTH THE ENCORE DUAL ARM OPERATOR AND THE ENCORE DYAD OPERATOR.

2 STUD BRACKET 12510.XX AND 12511.XX MAY NOT FIT IF 2.125/1.625 DIMENSION (SEE FIG. 1) IS LESS THAN 1.875. CONTACT TRUTH FOR RECOMMENDATIONS.

3 HOLD THIS DIMENSION AS CLOSE TO THE MINIMUM AS MANUFACTURING TOLERANCES ALLOW. A CLOSE FITTING CUT-OUT HELPS TO STABILIZE THE OPERATOR AGAINST ROCKING.

4. GASKET 32658 IS REQUIRED ON PVC AND METAL PROFILES FOR AN IMPROVED AIR AND WATER SEAL

5. HANDLE/COVER IS OPPOSITE HAND ON ENCORE DYAD OPERATORS. EXAMPLE: LH ENCORE DYAD OPERATORS REQUIRE RH HANDLE/COVER

FIG. 2 APPLICATION OF ENCORE DYAD OPERATOR CONTINUED(SILL MOUNT VERSION)

ENCORE™ DYADOPERATOR (SILL MOUNT)

26n

STAINLESS STEEL VERSION AVAILABLE

50.62 REAR MOUNT VERSION AVAILABLE

FOR USE WITH50.62 REAR MOUNTVERSION ONLY

(SILL MOUNT VERSION)

[125.4 mm]4.938

[107.9 mm]4.250

[92.1 mm]3.625

[76.2 mm]3.000

[31.7 mm]1.250

[15.9 mm].625[30.1 mm]

1.186[23.8 mm]

.938

[11.1 mm].437

[15.4 mm].606

RECOMMENDED SCREWS:

(QTY 6)(PN 19240.XX)#8 X 1 FLAT HEADSHEET METAL SCREW (SEE TRUTH TIPS FORMORE INFORMATION)

(QTY 2)FOR REAR MOUNT:(PN 19545.XX)#8-32 X 3/8 PAN HEAD MACHINE SCREW

50.60.XX.011 LEFT HAND SHOWN

FIG. 4 ENCORE TANGO HANDLE/COVER 12616.XX(RH)(SHOWN), 12614.XX(LH)

FIG. 5 BACK PLATE 21969.92[115.3 mm]

4.540

[7.3 mm].286

[16.9 mm].665

[4.7 mm].185

[135.4 mm]5.330

[40.8 mm]1.607

[41.0 mm]1.616

[18.5 mm].730

[38.4 mm]1.513

[129.1 mm]5.084

[14.2 mm].560

[11.7 mm].459

RECOMMENDED SCREWS:

(QTY 3)(PN 19240.XX)#8 X 1 FLAT HEAD SHEET METAL SCREW (SEE TRUTHTIPS FOR MORE INFORMATION)

[28.6 mm]1.125

[75.4 mm]2.970

[6.3 mm].250

[12.7 mm].500

[4.7 mm].186

[1.6 mm].062[8.5 mm]

.336

[55.5 mm]2.186

[27.8 mm]1.093

[35.1 mm]1.380

STAINLESS STEEL VERSION AVAILABLE

HAND OF BRACKET DOES NOT NECESSARILYMATCH HAND OF OPERATOR

FIG. 6 STUD BRACKET 12510.XX(LH) (SHOWN),12511.XX(RH)

[14.0 mm].553

FIG. 3 ENCORE DYAD OPERATOR(SILL MOUNT VERSION)

FIG. 4 ENCORE TANGO HANDLE/COVER 12616.XX(RH) (SHOWN) 12614.XX(LH)

FIG. 6 STUD BRACKET 12510.XX(LH) (SHOWN) 12511.XX(RH)

FIG. 5 BACK PLATE 21969.92