Reduce access network deployment projectrisk and troubleshooting time

More than 70% of IT organizations lackstandardized processes to validate deploymentand solve problems. This results in more than 1hour (average) to resolve problems. In addition,40% of IT tickets are not solved the first timeand require escalation. Intermittent problemscan take twice as long to resolve.

By automating and standardizing the validation& troubleshooting process, the OneTouch ATNetwork Assistant empowers novice networktechnicians to validate performance easily, solvemore problems faster, and escalate issues moreefficiently – allowing more IT projects to becompleted on time and with quality, freeing upengineer’s time.

Empower IT professional teams to effectively validate, andtroubleshoot Ethernet and Wi-Fi access networks

| DATA SHEETS |

Datasheet: OneTouch™ AT G2 Network Assistant

All-in-one: a handheld tester combining infrastructure, network service and end-to-end path performancemeasurement in one tool

Versatile: The OneTouch AT has a modular design: select the G2 module that has dual 10/100/1Gcopper/fiber Ethernet test ports and 802.11a/b/g/n/ac Wi-Fi radio, or the 10G module that has 100M/1/10Gcopper and fiber Ethernet test ports.

Standardize: Network engineer can pre-program AutoTest profiles for field technician to choose thatautomatically run a suite of test with the press of a button, enabling identification of the most commonproblems in about a minute

Authoritative: Measure end-to-end path performance prior and after the deployment of new services ornetwork infrastructure to assess network readiness and post deployment to prove SLA compliance

Visibility: Switched Ethernet and Wi-Fi discovery and analysis provides visibility and documentation intoconnected devices, key device properties and problems

Collaborative: Engineers can take full remote control of the OneTouch to collaborate with on-sitetechnicians and speed isolation of issues

VoIP ready: The G2 Module troubleshoots desktop SIP/SCCP based VoIP problems in real-time with inlinecall monitoring, logging and scoring

Capture friendly: Wired or Wi-Fi packet capture streamlines collaboration and escalation of the mostcomplex issues. Capture wireline traffic using the G2 module’s inline capture features avoids the need forSPAN port or TAP

Centralized Management: The Link-Live.com cloud portal offers visibility to all of the test results and projectprogress from any NETSCOUT portable tools, LinkSprinter, LinkRunner AT, AirCheck G2 and OneTouchAT, when the tester is dispatched for troubleshooting or validating network installation or change projects.Test results can be organized by project and recalled as baseline. User can also remote control OneTouchAT from the cloud and remotely update software of all OneTouch AT units claimed by their organization

1 of 22

OneTouch AT featuresVersatile copper, fiber and Wi-Fi troubleshootingBe ready for a broad range of troubleshooting scenarios with the handheld OneTouch AT G2 Network Assistant. The tester incorporates dual copper and fiber optic testports to facilitate troubleshooting of 10/100/1000 Mbps twisted pair and 100/1000 Mbps fiber Ethernet networks. The dual ports simplify inline packet capture and VoIPmonitoring by eliminating the need for mirror ports or taps. For troubleshooting Wi-Fi networks the OneTouch AT G2 tester incorporates an 802.11ac dual-band Wi-Firadio with a 3x3 antenna. When connected to both wired and Wi-Fi networks the tester displays test results side-by-side on a single page to aid in problem domainisolation.

The OneTouch AT Network Assistant has a modular design. A 10G module is available for testing wired 100Mbps to 10Gbps Ethernet switch port and link performance atup to 10Gbps rate.

All-in-one testing from the patch cable & Wi-Fi to the cloudWhen validating and troubleshooting the access network, one needs to test from where the client device is connected to the network—where the device could be a PC,tablet, smart phone, IP phone, printer, POS terminal, industrial equipment controller, a medical imager etc. The OneTouch AT can prove that the network is good —byemulating the client device and measuring network performance. It measures, analyzes and documents the performance of each the critical network elements: thenetwork cabling, the delivery of Power over Ethernet (PoE), the connection to the nearest switch, the connection to the nearest access point, and the performance of keynetwork services and server-based applications in the intranet, and cloud or internet.

Standardized network validation and troubleshootingUse the intuitive touch interface and the Setup Wizard to create test profiles, where a profile is a set of tests, tailored to specific networks, services, and applications. Buildprofiles to accommodate different types of users, devices, locations or technologies. Profiles can be very simple with just a few tests or advanced with dozens of tests.Once created, profiles can be saved for quick and easy reuse. Create a library of standardized profiles to elevate the troubleshooting know-how of the entire networksupport staff. Share profiles with other OneTouch AT users. Use the profiles to establish best practices for consistent, faster, more productive troubleshooting andnetwork acceptance testing.

2 of 22

Automated suits of test with pass/fail analysisTest everything defined in a profile automatically with the one button AutoTest. The AutoTest progresses from the physical layer of the network through the wired andwireless infrastructure, to network services and user-defined applications. Clear pass/fail and warning indicators highlight potential problems. A top-level pass/fail indicatorprovides the overall AutoTest status at a glance.

Figure 1. The AutoTest provides a comprehensivemeasurement of network performance from theend user point-of-view, from cable to services andapplications (Test result from OneTouch AT withG2 Modules for both Wired and Wi-Fi network shown)

User defined Performance TestsConnectivity & response time test to application/servers, and performance test toend-point(s) in all three network layers: the local broadcast domain, the privateintranet and the public cloud (Internet).

Client network AnalysisCable & nearest switch test, Wi-Fi network accessibility test, Wired and Wi-Fiaccess network/device discovery & network service tests: DHCP & DNS & 802.1x

3 of 22

Centralize Cloud-based managementOrganizations can claim their OneTouch AT units to the Link-Live.com cloud portal. Claimed units will be visible from the cloud portal as long as they are connected to theinternet. They can be remotely managed when and where convenient using a smart device through its web browser. Users can upload test results, download latestsoftware and test profiles, and remote control their OneTouch AT. Users can view and analyze test result on the cloud portal.

Centralize report managementLink-Live.com supports storing and viewing of test results from other NETSCOUT handheld network test products, such as LinkSprinter, LinkRunner AT, and AirCheckG2. After each test, test results and reports from these test units can be exported and stored to Link-Live.com. A user can setup such that an email will be sent to theoperator of the OneTouch so that he can enter comments, such as test location, and/or upload picture(s) of the test environment. Multiple parties can access the Link-liveCloud Portal over the web at anytime from anywhere using a smart device or PC via a web browser. Free-string match search, and filter condition make it easy to locatethe test report(s) of interest by text in comment or the test result.

Figure 2. Link-live consolidate test results from OneTouch AT and other NETSCOUT Handheld Network Test products.

4 of 22

Figure 3. Remotely control the OneTouch AT andaccess saved files using a PC, laptop, tablet orsmart phone

Remote visibility, control and file accessUse the built-in RJ-45 management port or optional USB Wi-Fi adapter to remotely control the OneTouch AT and access saved files. Any action that can be performeddirectly on the OneTouch AT using the touch screen can be performed remotely using a PC, laptop, tablet or smart phone. Minimize the time, expense and inconvenienceof traveling to the client location where the problem was reported. Webcam support enables live, remote viewing of the physical environment near the tester. Remotecontrol of units via the Cloud Service also allows traversal of NAT devices, which is very advantageous when troubleshooting from outside the office.

5 of 22

Figure 4. Test link speed over twisted pair and fiberoptic links at rates up to 1Gbps and measure POEvoltage with the G2 Module

Figure 5. Test a Wi-Fi connection at up to 802.11acrates and verify channel width, signal and noiselevel.

Test FeaturesCopper and fiber optic cable testingTroubleshoot cable performance quickly by measuring twisted pair cable wiremap and length. Use cable identifiers and tone probe, such as Fluke Networks IntellitoneTM,to locate and identify cables. Measure the optical power received through fiber optic links. Verify the cleanliness of fiber optic connections by viewing connector end faceswith the optional USB video probe, such as Fluke Networks FiberInspector™.

PoE testing (Supported with OneTouch AT G2 Module)Verify the successful delivery of PoE with the TruePower™ load test. Emulate an 802.3at (PoE+) class 1-4 powered device and measure power up to 25.5 watts. See therequested and received PoE class, the pairs used, the PSE type, measured PoE voltage unloaded and under load, and PoE power under load.

Wi-Fi and wired client devices connectivity testingUnderstand how a client device connects to the wired infrastructure by testing link negotiation, identifying the nearest switch, and monitoring key switch port statistics. TheOneTouch AT with G2 Module tests IEEE 802.11a, .11b, .11g, .11n and .11ac Wi-Fi networks. It shows understand how a client device connects to the Wi-Fiinfrastructure by testing the link between the client and the nearest access point, identifying the AP name, channel and security type, observing the authentication andassociation process, and monitoring key AP and network statistics, including roaming details by AP. For Wired client, the OneTouch AT with G2 Module tests10/100/1000BASE-T twisted pair and 100BASE-FX/1000BASE-X fiber optic Ethernet networks, while the OneTouch AT with 10G Module test RJ-45 test port for100/1000/10GBASE-T and 1000 BASE-X SFP/10 G BASE-SR/LR SFP+ Ethernet over optical fiber Network.

6 of 22

Figure 6. Detailed breakdown of DHCP provisioningand response performance

Figure 7. Path Analysis showing the path throughswitches from OneTouch to a client.

Network services testingTest DHCP server responsiveness. Identify the wired and Wi-Fi DHCP servers and view the offer and acceptance timing and the lease information. Test DNS serverresponsiveness. Identify the wired and Wi-Fi DNS servers and view the DNS lookup time. Also, determine if a second DHCP address is being offered. If unexpected or isa potential rogue server, use the path analysis tool - a layer 2 and layer 3 trace route - to track down the device to mitigate a problem situation.

7 of 22

Figure 8. Detailed breakdown of network-hostedapplication performance

Figure 9. Group tests by hosting location – local,intranet, internet

Network application testingDetermine if a server-based application is the root cause of a reported problem by measuring availability and response metrics. Add to the AutoTest profile theperformance test appropriate for the application: ping (ICMP), connect (TCP), web (HTTP), file (FTP), multicast (IGMP), video (RTSP) or email (SMTP). Each test isgraphically represented on the OneTouch AT home page as an icon. After running the AutoTest, touch a test icon on the home page to get a detailed breakdown ofapplication performance including DNS lookup time, server response time and data rate. The test results are presented side-by-side for easy wired/Wi-Fi and IPv4/IPv6performance comparisons. A few examples: ping your WLAN controller, connect to port 2000 on your VoIP call manager, download a page of an application with a webinterface, upload or download a file from a server, subscribe to a multicast group, access video content from an on-demand streaming video server or email a textmessage to your mobile phone.

8 of 22

Local, intranet and internet performanceUnderstand the performance of network services and server-based applications wherever they are hosted: locally in the datacenter, on a corporate intranet server or on aserver reached via the public internet. Create location centric AutoTest profiles by grouping together co-located services and applications. Measure service levels to thedifferent groups to quickly spot problems.

Enterprise network managers use the Wired Performance tests for: Assessing network performance prior to deployment of new services or network infrastructureValidating the performance of newly installed network infrastructure and critical network links within the LAN or data centerTroubleshooting network and service performance problemsVerifying independently that service providers are meeting agreed upon service levels (SLAs) and maintaining QoS end-to-end

Service providers and system integrators use the Wired Performance tests for: Documenting network performance from layer 1 to 7 where the documentation serves as proof that the services they provided were delivered successfullyProviding value-added service to their enterprise customers in the form of network assessments and troubleshooting

1G and Wi-Fi End-to-end path performance measurementEnsure that newly installed or upgraded wired and Wi-Fi networks meet SLA objectives and are ready for new high-bandwidth applications by measuring end-to-end pathperformance. Measure throughput, frame loss, latency and jitter between a local OneTouch AT G2 connected to Wi-Fi or wired client network, and a remote OneTouchAT peer or a remote LinkRunner reflector connected to the end of path to test. A remote peer provides upstream and downstream results while a remote reflector yieldsround trip results. Measure performance at rates up to 1 Gbps on copper and fiber networks and 600 Mbps on Wi-Fi networks. A special use model exists that enablestesting from the OneTouch AT wired interface to the Wi-Fi interface on the same instrument for testing without a remote.

Figure 10. End-to-end path performancemeasurement validates link readiness andSLA compliance

9 of 22

The OneTouch AT with G2 Module will be located at one end. There are options for the test instrument to be located at the other end of the link. The OneTouch AT withG2 Module also support loop back testing to itself from its Wire to its WiFi interface.

Remote Tester (End-Point)

OneTouch AT G2 as local LinkRunner AT 2000 OneTouch AT G2 (wired)

< 600Mbps Wi-Fi ✓ ✓

≤ 1 Gbps rate ✓ ✓

1 traffic stream ✓ ✓

IETF RFC 2544 test method ✓ ✓

Round trip results ✓

Bi-directional results OneTouch AT G2 (wired)

Frame loss, latency, jitter ✓ ✓

10 of 22

10G End-to-end path performance measurementThe OneTouch AT with 10G Module features 10G and 1G Wired Performance tests for validating and troubleshooting end-to-end network path performance. TheseWired Performance tests facilitate measurement of throughput, frame loss, latency and jitter across wide area networks, local area networks and within sites anddatacenters.

Figure 11. Detailed breakdown of XG customperformance

Figure 12. Detailed breakdown of wired to peer

The OneTouch AT with 10G module will be located at one end. There are options for the test instrument to be located at the other end of the link.

11 of 22

Remote Tester (End-Point)

OneTouch AT 10G as local LinkRunner AT 2000 OneTouch AT G2 OneTouch AT 10G OptiView XG

≤ 1 Gbps rate ✓ ✓ ✓

1 traffic stream ✓ ✓ ✓

IETF RFC 2544 test method ✓ ✓ ✓

Round trip results ✓

Bi-directional results ✓ ✓

Frame loss, latency, jitter ✓ ✓ ✓

≤ 10 Gbps rate ✓

≤ 4 traffic streams ✓

ITU Y.1564 test method ✓

Throughput, availability,information rate, burst rate

✓

Class of service testing, trafficpolicing

✓

12 of 22

Figure 13. Analyze Wi-Fi health by each availablechannels.

Figure 14. Visibility into each Wi-Fi channel,showing bandwidth occupied by 802.11 and non-802.11 traffic

Wired network discovery and analysisAutomatically discover copper and fiber-connected devices and key device properties. Select from among fourteen different sorts to obtain different views into the wirednetwork. For example, sort by IPv4 or IPv6 address to identify used and available addresses. Or sort by switch name/slot/port to understand where on the networkdevices are connected. Sort by discovered problems to quickly identify potential issues. Additional discovery-assisted analysis tools aid with troubleshooting and profilecreation. For example, the Multiport Statistics tool provides visibility into switch, router and AP port statistics including speed, duplex, slot, port, VLANs, host count,utilization, discards and errors. The Devices on Port tool provides visibility into the devices connected to an individual switch port. The Path Analysis tool provides a layer2 and 3 trace route from the OneTouch AT to a target device including time to each hop and SNMP switch and router port statistics.

Wi-Fi discovery and analysis (supported by OneTouch AT with G2 Module)Automatically discover Wi-Fi devices and key device properties. Select from among twenty context-relative sorts to obtain different views into the wireless network. Forexample, sort by signal strength to troubleshoot Wi-Fi coverage issues. Sort by MAC manufacturer to discover Wi-Fi devices by type and to understand how they areconnected relative to SSID, AP and channel. Sort by channel to identify channel spacing and usage problems. Sort by authorization status to find potential securityviolations. Additional discovery-assisted analysis tools aid with troubleshooting and security enforcement. If a Wi-Fi device is also discovered via Wired Analysis, theCross Link feature enables one-button toggling between wired and Wi-Fi analysis views.

13 of 22

Figure 17. Inline VoIP analysis simplifiestroubleshooting of desktop VoIP problems in real-time without TAPs or switch mirror ports

Figure 18. VoIP Analysis shows the entire callsetup process as well as quality of the VoIP call ineach direction

Figure 15. Unique Interferer analysis classifysources of non-802.11

Figure 16. Explanation of non-802.11 sources andhow to mitigate

Inline VoIP analysis (Supported by OneTouch AT G2 Module only)Connect the OneTouch AT inline between an IP phone and the network for real-time troubleshooting and analysis. The VoIP analysis test reveals issues related to PoE,DHCP, TFTP, SIP, and SCCP. The test provides visibility into unencrypted SIP and SCCP traffic to debug VoIP phone problems and quantify the quality of a VoIP call.Simultaneous capture of the VoIP conversation is optional.

14 of 22

Packet captureCapture wired and AutoTest traffic when a packet-level view is required to solve a complex network or application issue. Filter the traffic to capture what is most important.Export the capture file to a PC for decoding and analysis using protocol analysis software. Capture wired traffic on a single port, on two ports aggregated, or inlinebetween a client device and the network. Inline capture avoids the complexity, time and cost associated with standalone taps or configuring switch mirror ports. TheOneTouch AT with G2 Module can capture VoIP traffic, and Wi-Fi traffic by channel and mode (20 MHz or 40 MHz+).

Figure 19. Inline packet capture simplifiesdocumentation of client application problemswithout TAPs or SPAN ports

Figure 20. Capture packets to solve complex issues

Streamline collaborationCollaborate with peers, consultants, integrators and vendors more effectively by sharing packet captures, screen shots and AutoTest reports. Remotely control and viewthe user interface and remotely access files using a PC, tablet or smart phone. Attach a web cam to the OneTouch AT to share a view of the test environment.

Save test resultsSave the test results to share with colleagues or outside parties. A report serves as trouble ticket documentation, as a record of historical performance for benchmarkingor as a certification report after new infrastructure deployment and turn up. Define which test results to include in the report (AutoTest, Wired Analysis, Wi-Fi Analysis,Tools Settings, and VoIP Analysis) and the report format (PDF, XML). Open the results in a spreadsheet for flexibility in results analysis.

15 of 22

Setup wizardSimplify AutoTest profile creation while learning about the tester's capabilities by running the Setup Wizard. The wizard simplifies profile creation with step-by-step guidedinstructions, yes/no prompts, on-screen help and graphical progress indicators. Experienced users can bypass the wizard if desired.

Figure 21. Setup Wizard simplifies creation ofAutoTest profiles

Figure 22. Detailed breakdown of network serviceperformance

Purpose-built for use by field teamThe OneTouch AT is engineered specifically for network support professionals on the go. Useful test and management tools include a web browser, Telnet/SSH client,cable toner, webcam support and optional fiber optic connector inspection camera. Remote control over web-browser enable collaboration between field team and skilledengineering resources in back-office. The durable platform provides years of reliable operation in tough environments.

Gold SupportProtect your investment with Gold Support. Gold Support benefits include free software upgrades and MIB updates, unlimited priority repair service with loaner units,annual factory performance verification, free accessory replacement and 24x7 technical support with priority members-only access numbers.

16 of 22

Technical SpecificationsGeneral

Dimensions (with module and battery installed) 10.3 in x 5.3 in x 2.9 in (26.2 cm x 13.5 cm x 7.3 cm)

Weight (with module and battery installed) 3.5 lb. (1.6 kg)

Display 5.7 in (14.5 cm) LCD with projected capacitance touch screen, 480 x 640 pixels

AC adapterInput: 100-240 VAC, 50-60 Hz, 1.0 AOutput: +15 VDC, 2.0 A

Battery type Lithium ion battery pack, 7.2 V

Battery lifeApproximately 3-4 hours depending on type of usage, 4 hours to charge from 10% capacity to 90%capacity with the unit powered off

MemoryInternal: 2 GB shared between system and user filesSD card: 4/8 GB, brand and model selected for optimal performanceUSB 2.0 type A port: for use with USB mass storage devices

Management portOne RJ-45 10/100BASE-T EthernetOne USB 802.11 (requires optional adapter)

G2 Module Network Interfaces

Network analysis portsTwo RJ-45 10/100/1000BASE-T EthernetTwo SFP 100BASE-FX/1000BASE-X Ethernet

Wi-Fi adapter data rate

802.11a: 6/9/12/24/36/48/54 Mbps802.11b: 1/2/5.5/11 Mbps802.11g: 6/9/12/24/36/48/54 Mbps802.11n (20 MHz): MCS0-23, up to 216 Mbps802.11n (40 MHz): MCS0-23, up to 450 Mbps802.11ac (80 MHz): MCS0NSS1-MCS9NSS3, up to 1.3 Gbps

Wi-Fi adapter operating frequency2.412 ~ 2.484 GHz (Industrial Scientific Medical Band)5.170 ~ 5.825 GHz

Wi-Fi security 64/128-Bit WEP Key, WPA/WPA2 personal, WPA/WPA2 enterprise, 802.1X

17 of 22

10G Module Network Interfaces

Network analysis ports100/1000/10 G BASE-T RJ-45 Ethernet over twisted pair1000 BASE-X SFP/10 G BASE-SR/LR SFP+ Ethernet over optical fiber

Management portOne RJ-45 10/100 BASE-T EthernetOne USB 802.11 (requires optional adapter)

Supported network standardsIEEE 100 BASE-T, IEEE 1000 BASE-T, IEEE 10 G BASE-T, IEEE 1000 BASE-X, IEEE 10 GBBASE-SR, IEEE 10 G BASE-LR

RFCs and standard MIBs used1213, 1231, 1239, 1285, 1493, 1512, 1513, 1643, 1757, 1759, 2021, 2108, 2115, 2127, 2233, 2495,2515, 2558, 2618, 2737, 2790, 2819, 3592, 3895, 3896, 4188, 4502.

Note: The OneTouch AT analyzer is NOT designed for connection to a telephone network, ISDN line. Do not connect to a telephone network or ISDN line except through a regulatory agency compliantcomputer network modem device.

Copper Cables Test

Cable types100 Ω Unshielded Twisted Pair (UTP) LAN cables.100 Ω Shielded or Screened Twisted Pair (STP) LAN cables.TIA Category 3, 4, 5, 5e, and 6. ISO Class C, D, E and F.

Cable length measurementMeasurable cable lengths are from 3 feet (1meter) to 656 feet (200 meters).

Accuracy: ± 30 feet (±10 meters).

Length measurement is based on NominalVelocity of Propagation (NVP) for CAT 5e cable.

18 of 22

Environmental and Regulatory

Operating temperature 32°F to 122°F (0°C to 50°C)

Battery charging temperature 32°F to 104°F (0°C to 40°C)

Storage temperature-40°F to 160°F (-40°C to 71°C)-4°F to 122°F (-20°C to 50°C) for periods longer than 1 week

Operating relative humidity(% RH without condensation)

5% to 45% at 32°F to 122°F (0°C to 50°C)5% to 75% at 32°F to 104°F (0°C to 40°C)5% to 95% at 32°F to 86°F (0°C to 30°C)

Shock and vibration Meets the requirements of MIL-PRF-28800F for Class 3 Equipment

Safety CAN/CSA-C22.2 No. 61010-1-04, IEC 61010-1:2001

Operating altitude 13,123 ft (4,000 m), 10,500 ft (3,200 m) with AC adapter

Storage altitude 39,370 ft (12,000 m)

Pollution degree 2

EMC EN 61326-1:2006

Certifications and Compliance

Conformite Europeene. Conforms to the requirements of the European Union and the European Free Trade Association (EFTA).

Listed by the Canadian Standards Association.

Conforms to relevant Australian standards.

Conforms to relevant South Korean EMC Standards.

19 of 22

Models, Options and AccessoriesMainframes:

Model Description

1TG2-1500 ONETOUCH AT G2 ETHERNET TESTER

1TG2-3000 ONETOUCH AT G2 ETHERNET WI-FI TESTER

1T10G-1000 ONETOUCH AT 10G ETHERNET TESTER

Gold Support:One year and three year gold support is available for mainframes, bundles and upgrades. We encourage customers to purchase Gold Support at the time of purchase.Purchase of Gold Support after product was shipped will be subjected to back-date charge. Please contact your nearest NETSCOUT sales representative for model andpricing.

Item Description

1TG2-1500-1YS 1 Year Gold Tools Support for 1TG2-1500

1TG2-1500-3YS 3 Year Gold Tools Support for 1TG2-1500

1TG2-3000-1YS 1 Year Gold Tools Support for 1TG2-3000

1TG2-3000-3YS 3 Year Gold Tools Support for 1TG2-3000

1T10G-1000-1YS 1 Year Gold Tools Support for 1T10G-1000

1T10G-1000-3YS 3 Year Gold Tools Support for 1T10G-1000

20 of 22

Options & Accessories:

Model Description

1TG2-3000-MOD 1TG2-3000-MOD,ONETOUCH AT G2 ETHERNET WI-FI TEST MODULE

1T10G-1000-MOD 1T10G-1000-MOD,ONETOUCH AT 10G ETHERNET TEST MODULE

1TG2-ETH-OPT 1TG2-ETH-OPT,ONETOUCH AT G2 ETHERNET UPGRADE

1TG2-WIFI-OPT 1TG2-WIFI-OPT,ONETOUCH AT G2 WI-FI UPGRADE

1T-ANT 1T-ANT,ONETOUCH AT EXTERNAL DIRECTIONAL ANTENNA

SFP-1000LX SFP-1000LX,LX GIG FIBER DDM SFP TRANSCEIVER

SFP-1000SX SFP-1000SX,SX GIG FIBER DDM SFP TRANSCEIVER

SFP-1000ZX SFP-1000ZX,ZX GIG FIBER DDM SFP TRANSCEIVER

SFP-100FX SFP-100FX,100BASE-FX FIBER DDM SFP TRANSCEIVER

WIREVIEW 1 WIREVIEW 1,WIREVIEW WIREMAPPER #1

WIREVIEW 2-6 WIREVIEW 2-6,WIREVIEW CABLE ID SET 2 THRU 6

Bundles:

Model Description

1TG2-1500/GLD 1TG2-1500/GLD,ONETOUCH AT G2 1500 AND 1 YR GOLD SUPPORT

1TG2-3000/GLD 1TG2-3000/GLD,ONETOUCH AT G2 3000 AND 1 YR GOLD SUPPORT

1T10G-1000/GLD 1T10G-1000/GLD,ONETOUCH AT 10G 1000 AND 1 YR GOLD SUPPORT

1TG2-3000-1T10G1M 1TG2-3000-1T10G1M,ONETOUCH AT G2 3000 AND ONETOUCH AT 10G 1000 MODULE

1TG2-1500-LRAT2 1TG2-1500-LRAT2,ONETOUCH AT G2 1500 AND LINKRUNNER AT 2000

1TG2-3000-LRAT2 1TG2-3000-LRAT2,ONETOUCH AT G2 3000 AND LINKRUNNER AT 2000

1TG2-1500-2PK 1TG2-1500-2PK,ONETOUCH AT G2 1500 2-PACK

21 of 22

Gold Support for Bundles:

Model Description

1TG2-1500-2PK-1YS 1 Year Gold Tools Support for 1TG2-1500-2PK

1TG2-1500-2PK-3YS 3 Year Gold Tools Support for 1TG2-1500-2PK

1TG2-1500-LRAT2-1YS 1 Year Gold Tools Support for 1TG2-1500-LRAT2

1TG2-1500-LRAT2-3YS 3 Year Gold Tools Support for 1TG2-1500-LRAT2

1TG2-30001T10G1M-1YS 1 Year Gold Tools Support for 1TG2-3000-1T10G1M

1TG2-30001T10G1M-3YS 3 Year Gold Tools Support for 1TG2-3000-1T10G1M

1TG2-3000-LRAT2-1YS 1 Year Gold Tools Support for 1TG2-3000-LRAT2

1TG2-3000-LRAT2-3YS 3 Year Gold Tools Support for 1TG2-3000-LRAT2

© 2016 NETSCOUT. Rev: 09/14/2016 11:13 am (Literature Id: 4212995)

22 of 22