emerson ld190, ld195, 19md359 tv-dvd_lcd

LCD TV/DVDchassis FL9.3

SERVICE MANUALContents

19 LD195SSX SYLVANIA Limited19 LD195EMX EMERSON19 19MD359B/F7 MAGNAVOX19 LD190EM1 EMERSON19 19MD350B/F7 MAGNAVOX19 LD190SS1 SYLVANIA Limited

2010 Funai Electric Co., Ltd.

All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed, downloaded or stored in any storage medium, in any form or for any purpose without the express prior written consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited.

Information in this document is subject to change without notice. Funai reserves the right to change the content herein without the obligation to notify any person or organization of such changes.

with the design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way without the express written consent of Funai. All other trademarks used herein remain the exclusive property of their respective owners. Nothing contained in this manual should be construed as granting, by implication or otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights to the fullest extent of the law.

A94N1UH/A94N4UH/A94N0UH/A9DN4UH/A9DN0UH/A9DN1UH100401

IMPORTANT SAFETY NOTICEProper service and repair is important to the safe, reliable operation of all Funai Equipment. The service procedures recommended by Funai and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended.It is important to note that this service manual contains various CAUTIONS and NOTICES which should be carefully read in order to minimize the risk of personal injury to service personnel. The possibility exists that improper service methods may damage the equipment. It also is important to understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE. Funai could not possibly know, evaluate and advice the service trade of all conceivable ways in which service might be done or of the possible hazardous consequences of each way. Consequently, Funai has not undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not recommended by Funai must first use all precautions thoroughly so that neither his safety nor the safe operation of the equipment will be jeopardized by the service method selected.

The LCD panel is manufactured to provide many years of useful life. Occasionally a few non active pixels may appear as a tiny spec of color. This is not to be considered a defect in the LCD screen.

Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.

TABLE OF CONTENTSSpecifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1Laser Beam Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1Standard Notes for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1Cabinet Disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1Electrical Adjustment Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 How to Initialize the LCD TV/DVD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1Firmware Renewal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1Schematic Diagrams / CBA and Test Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1System Control Timing Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1Lead Identifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-1Exploded Views. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-1Mechanical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-1Electrical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-1Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-1

1-1 A94N1SP

SPECIFICATIONS< LCD TV Section >< TUNER / NTSC >

ANT. Input ---------------------- 75 Unbal., F type

< TUNER / ATSC >

< LCD PANEL >

< VIDEO >

< AUDIO >All items are measured across 8 load at speaker output terminal with L.P.F.

Description Condition Unit Nominal Limit1. AFT Pull-In Range --- MHz 2.3 2.1

2. Synchronizing Sens.TV.ch.4

CA.ch.31CA.ch.87

dBdBdB

181818

202023

Description Condition Unit Nominal Limit1. Received Freq. Range (-28dBm) --- kHz --- 100

2. ATSC Dynamic Range (min / max)ch.4ch.10ch.41

dBmdBmdBm

---

---

---

-76/0-76/0

-76/+4

Description Condition Unit Nominal Limit

1. Native Pixel Resolution HorizontalVerticalpixelspixels

1366768

---

---

2. Brightness (w / filter) --- cd/m2

280 [LD195SSX, LD195EMX,

19MD359B/F7]230

[LD190EM1, 19MD350B/F7,

LD190SS1]

---

3. Viewing Angle HorizontalVertical

-85 to 85-80 to 80

---

---

Description Condition Unit Nominal Limit

1. Over Scan HorizontalVertical%%

55

5555

2. Color Temperature---

xy

K 120000.2720.278

---

3%3%

3. Resolution (composite video) HorizontalVerticallineline

400350

---

---

Description Condition Unit Nominal Limit1. Audio Output 10% Distortion (ATSC 0 dBfs) Lch/Rch W 1.5/1.5 1.3/1.32. Audio Distortion (NTSC) 500mW: Lch/Rch % 0.5/0.5 2.0/2.03. Audio Freq. Response (NTSC) -6dB: Lch

-6dB: RchHzHz

70 to 10 k70 to 10 k

---

---

1-2 A94N1SP

< DVD >

Note: Nominal specifications represent the design specifications. All units should be able to approximate these. Some will exceed and some may drop slightly below these specifications. Limit specifications represent the absolute worst condition that still might be considered acceptable. In no case should a unit fail to meet limit specifications.

Description Condition Unit Nominal Limit1. Horizontal Resolution (TDV-540 TIT.2 CHP.16) --- Line 350 3302. Audio Distortion (LPCM 48 kHz, W/LPF) (PTD 1-NOR TIT.1 CHP.1)

LR % 0.03 0.07

3. Audio freq. response (LPCM 48 kHz) (PTD 1-NOR TIT.1 CHP.5 -- 10)

L, 20 HzR, 20 HzL, 20 kHzR, 20 kHz

dB 0 +4/-5

4. Audio S/N (LPCM 48 kHz, W/LPF, A-WTD) (PTD 1-NOR TIT.1 CHP.1 -- 2)

LR dB 85 75

2-1 TVDVDN_LBSP

LASER BEAM SAFETY PRECAUTIONSThis DVD player uses a pickup that emits a laser beam.

The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep your eyes at least 30 cm away from the pickup lens when the diode is turned on. Do not look directly at the laser beam.CAUTION: Use of controls and adjustments, or doing procedures other than those specified herein, may result in hazardous radiation exposure.

Location: Top of LCD module.

Do not look directly at the laser beam coming from the pickup or allow it to strike against your skin.

Drive Mechanism Assembly

Laser Beam Radiation

Laser Pickup

Turntable

3-1 LTVN_ISP

IMPORTANT SAFETY PRECAUTIONSPrior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.

Safety Precautions for LCD TV Circuit1. Before returning an instrument to the

customer, always make a safety check of the entire instrument, including, but not limited to, the following items:a. Be sure that no built-in protective devices are

defective and have been defeated during servicing. (1) Protective shields are provided on this chassis to protect both the technician and the customer. Correctly replace all missing protective shields, including any removed for servicing convenience. (2) When reinstalling the chassis and/or other assembly in the cabinet, be sure to put back in place all protective devices, including but not limited to, nonmetallic control knobs, insulating fishpapers, adjustment and compartment covers/shields, and isolation resistor/capacitor networks. Do not operate this instrument or permit it to be operated without all protective devices correctly installed and functioning. Servicers who defeat safety features or fail to perform safety checks may be liable for any resulting damage.

b. Be sure that there are no cabinet openings through which an adult or child might be able to insert their fingers and contact a hazardous voltage. Such openings include, but are not limited to, (1) spacing between the Liquid Crystal Panel and the cabinet mask, (2) excessively wide cabinet ventilation slots, and (3) an improperly fitted and/or incorrectly secured cabinet back cover.

c. Antenna Cold Check - With the instrument AC plug removed from any AC source, connect an electrical jumper across the two AC plug prongs. Place the instrument AC switch in the on position. Connect one lead of an ohmmeter to the AC plug prongs tied together and touch the other ohmmeter lead in turn to each tuner antenna input exposed terminal screw and, if applicable, to the coaxial connector. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohm, an abnormality exists that must be corrected before the instrument is returned to the customer. Repeat this test with the instrument AC switch in the off position.

d. Leakage Current Hot Check - With the instrument completely reassembled, plug the AC line cord directly into a 120 V AC outlet. (Do not use an isolation transformer during this test.) Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI) C101.1 Leakage Current for Appliances and Underwriters Laboratories (UL) 1410, (50.7). With the instrument AC switch first in the on position and then in the off position, measure from a known earth ground (metal water pipe, conduit, etc.) to all exposed metal parts of the instrument (antennas, handle brackets, metal cabinet, screw heads, metallic overlays, control shafts, etc.), especially any exposed metal parts that offer an electrical return path to the chassis. Any current measured must not exceed 0.5 milli-ampere. Reverse the instrument power cord plug in the outlet and repeat the test.

ANY MEASUREMENTS NOT WITHIN THE LIMITS SPECIFIED HEREIN INDICATE A POTENTIAL SHOCK HAZARD THAT MUST BE ELIMINATED BEFORE RETURNING THE INSTRUMENT TO THE CUSTOMER OR BEFORE CONNECTING THE ANTENNA OR ACCESSORIES.

2. Read and comply with all caution and safety-related notes on or inside the receiver cabinet, on the receiver chassis, or on the Liquid Crystal Panel.

ALSO TEST WITHPLUG REVERSEDUSING ACADAPTER PLUGAS REQUIRED

TEST ALL EXPOSEDMETAL SURFACES

READING SHOULD NOT BE ABOVE 0.5 mA

EARTHGROUND

_

DEVICELEAKAGECURRENT

TESTER

+BEINGTESTED

3-2 LTVN_ISP

3. Design Alteration Warning - Do not alter or add to the mechanical or electrical design of this TV receiver. Design alterations and additions, including, but not limited to circuit modifications and the addition of items such as auxiliary audio and/or video output connections, might alter the safety characteristics of this receiver and create a hazard to the user. Any design alterations or additions will void the manufacturer's warranty and may make you, the servicer, responsible for personal injury or property damage resulting therefrom.

4. Hot Chassis Warning -a. Some TV receiver chassis are electrically

connected directly to one conductor of the AC power cord and maybe safety-serviced without an isolation transformer only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC power source. To confirm that the AC power plug is inserted correctly, with an AC voltmeter, measure between the chassis and a known earth ground. If a voltage reading in excess of 1.0 V is obtained, remove and reinsert the AC power plug in the opposite polarity and again measure the voltage potential between the chassis and a known earth ground.

b. Some TV receiver chassis normally have 85V AC(RMS) between chassis and earth ground regardless of the AC plug polarity. This chassis can be safety-serviced only with an isolation transformer inserted in the power line between the receiver and the AC power source, for both personnel and test equipment protection.

c. Some TV receiver chassis have a secondary ground system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulation material that must not be defeated or altered.

5. Observe original lead dress. Take extra care to assure correct lead dress in the following areas: a. near sharp edges, b. near thermally hot parts-be sure that leads and components do not touch thermally hot parts, c. the AC supply, d. high voltage, and, e. antenna wiring. Always inspect in all areas for pinched, out of place, or frayed wiring. Check AC power cord for damage.

6. Components, parts, and/or wiring that appear to have overheated or are otherwise damaged should be replaced with components, parts, or wiring that meet original specifications. Additionally, determine the cause of overheating and/or damage and, if necessary, take corrective action to remove any potential safety hazard.

7. Product Safety Notice - Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection, nor can the protection they give necessarily be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by a # on schematics and in parts lists. Use of a substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire, and/or other hazards. The product's safety is under review continuously and new instructions are issued whenever appropriate. Prior to shipment from the factory, our products are strictly inspected to confirm they comply with the recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.

3-3 LTVN_ISP

Precautions during ServicingA. Parts identified by the # symbol are critical for

safety.Replace only with part number specified.

B. In addition to safety, other parts and assemblies are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements.Examples: RF converters, RF cables, noise blocking capacitors, and noise blocking filters, etc.

C. Use specified internal wiring. Note especially:1) Wires covered with PVC tubing2) Double insulated wires3) High voltage leads

D. Use specified insulating materials for hazardous live parts. Note especially:1) Insulation Tape2) PVC tubing3) Spacers4) Insulators for transistors.

E. When replacing AC primary side components (transformers, power cord, etc.), wrap ends of wires securely about the terminals before soldering.

F. Observe that the wires do not contact heat producing parts (heat sinks, oxide metal film resistors, fusible resistors, etc.)

G. Check that replaced wires do not contact sharp edged or pointed parts.

H. When a power cord has been replaced, check that 5~6 kg of force in any direction will not loosen it.

I. Also check areas surrounding repaired locations.J. Use care that foreign objects (screws, solder

droplets, etc.) do not remain inside the set.K. When connecting or disconnecting the internal

connectors, first, disconnect the AC plug from the AC supply outlet.

L. When installing parts or assembling the cabinet parts, be sure to use the proper screws and tighten certainly.

3-4 LTVN_ISP

Safety Check after ServicingExamine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards.

1. Clearance DistanceWhen replacing primary circuit components, confirm specified clearance distance (d) and (d') between soldered terminals, and between terminals and surrounding metallic parts. (See Fig. 1)Table 1: Ratings for selected area

Note: This table is unofficial and for reference only. Be sure to confirm the precise values.

2. Leakage Current TestConfirm the specified (or lower) leakage current between B (earth ground, power cord plug prongs) and externally exposed accessible parts (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks, etc.) is lower than or equal to the specified value in the table below.Measuring Method: (Power ON)Insert load Z between B (earth ground, power cord plug prongs) and exposed accessible parts. Use an AC voltmeter to measure across both terminals of load Z. See Fig. 2 and following table.

Table 2: Leakage current ratings for selected areas

Note: This table is unofficial and for reference only. Be sure to confirm the precise values.

AC Line Voltage Region Clearance Distance (d), (d)

110 to 130 V U.S.A. or Canada 3.2 mm

(0.126 inches)

AC Line Voltage Region Load Z Leakage Current (i) Earth Ground (B) to:110 to 130 V U.S.A. or Canada

0.15 F CAP. & 1.5 k RES. Connected in parallel i 0.5 mA rms

Exposed accessible parts

Chassis or Secondary Conductor

Primary Circuit

Fig. 1

d' d

AC Voltmeter (High Impedance)

Exposed Accessible Part

B Earth Ground Power Cord Plug Prongs

Z

Fig. 2

4-1 TVDVDN_SN

STANDARD NOTES FOR SERVICINGCircuit Board Indications1. The output pin of the 3 pin Regulator ICs is

indicated as shown.

2. For other ICs, pin 1 and every fifth pin are indicated as shown.

3. The 1st pin of every male connector is indicated as shown.

Instructions for Connectors1. When you connect or disconnect the FFC (Flexible

Foil Connector) cable, be sure to first disconnect the AC cord.

2. FFC (Flexible Foil Connector) cable should be inserted parallel into the connector, not at an angle.

Pb (Lead) Free SolderPb free mark will be found on PCBs which use Pb free solder. (Refer to figure.) For PCBs with Pb free mark, be sure to use Pb free solder. For PCBs without Pb free mark, use standard solder.

How to Remove / Install Flat Pack-IC1. RemovalWith Hot-Air Flat Pack-IC Desoldering Machine:1. Prepare the hot-air flat pack-IC desoldering

machine, then apply hot air to the Flat Pack-IC (about 5 to 6 seconds). (Fig. S-1-1)

2. Remove the flat pack-IC with tweezers while applying the hot air.

3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)

4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)

CAUTION:1. The Flat Pack-IC shape may differ by models. Use

an appropriate hot-air flat pack-IC desoldering machine, whose shape matches that of the Flat Pack-IC.

2. Do not supply hot air to the chip parts around the flat pack-IC for over 6 seconds because damage to the chip parts may occur. Put masking tape

Top View

Out In

Bottom ViewInput

5

10

Pin 1

Pin 1

FFC Cable

Connector

CBA

* Be careful to avoid a short circuit.

Pb free mark

Fig. S-1-1

4-2 TVDVDN_SN

around the flat pack-IC to protect other parts from damage. (Fig. S-1-2)

3. The flat pack-IC on the CBA is affixed with glue, so be careful not to break or damage the foil of each pin or the solder lands under the IC when removing it.

With Soldering Iron:1. Using desoldering braid, remove the solder from

all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3)

2. Lift each lead of the flat pack-IC upward one by one, using a sharp pin or wire to which solder will not adhere (iron wire). When heating the pins, use a fine tip soldering iron or a hot air desoldering machine. (Fig. S-1-4)



Hot-airFlat Pack-ICDesolderingMachine

CBA

Flat Pack-IC

Tweezers

Masking Tape

Fig. S-1-2

Flat Pack-IC Desoldering Braid

Soldering Iron

Fig. S-1-3

Fine TipSoldering Iron

SharpPin

Fig. S-1-4

4-3 TVDVDN_SN

With Iron Wire:1. Using desoldering braid, remove the solder from

all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3)

2. Affix the wire to a workbench or solid mounting point, as shown in Fig. S-1-5.

3. While heating the pins using a fine tip soldering iron or hot air blower, pull up the wire as the solder melts so as to lift the IC leads from the CBA contact pads as shown in Fig. S-1-5.



Note: When using a soldering iron, care must be taken to ensure that the flat pack-IC is not being held by glue. When the flat pack-IC is removed from the CBA, handle it gently because it may be damaged if force is applied.

2. Installation1. Using desoldering braid, remove the solder from

the foil of each pin of the flat pack-IC on the CBA so you can install a replacement flat pack-IC more easily.

2. The I mark on the flat pack-IC indicates pin 1. (See Fig. S-1-7.) Be sure this mark matches the pin 1 on the PCB when positioning for installation. Then presolder the four corners of the flat pack-IC. (See Fig. S-1-8.)

3. Solder all pins of the flat pack-IC. Be sure that none of the pins have solder bridges.

To Solid Mounting Point

Soldering Iron

Iron Wire

or

Hot Air Blower

Fig. S-1-5

Fine TipSoldering IronCBA

Flat Pack-ICTweezers

Fig. S-1-6

Example :

Pin 1 of the Flat Pack-ICis indicated by a " " mark. Fig. S-1-7

Presolder

CBA

Flat Pack-IC

Fig. S-1-8

4-4 TVDVDN_SN

Instructions for Handling Semi-conductorsElectrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work.

1. Ground for Human BodyBe sure to wear a grounding band (1 M) that is properly grounded to remove any static electricity that may be charged on the body.

2. Ground for WorkbenchBe sure to place a conductive sheet or copper plate with proper grounding (1 M) on the workbench or other surface, where the semi-conductors are to be placed. Because the static electricity charge on clothing will not escape through the body grounding band, be careful to avoid contacting semi-conductors with your clothing.

CBA

Grounding Band

Conductive Sheet orCopper Plate

1M

1M

CBA

5-1 A94N1DC

CABINET DISASSEMBLY INSTRUCTIONS1. Disassembly FlowchartThis flowchart indicates the disassembly steps for the cabinet parts, and the CBA in order to gain access to item(s) to be serviced. When reassembling, follow the steps in reverse order. Bend, route and dress the cables as they were.

2. Disassembly Method

Step/Loc. No.

Part

Removal

Fig. No.

Remove/*Unhook/Unlock/Release/Unplug/Unclamp/

DesolderNote

[1] Stand Assembly D1 3(S-1) ---

[2] Rear Cabinet D1 10(S-2), 2(S-3), (S-4) ---

[3] DVD Holder D2D54(S-5), 3(S-6), *CN901, *CN902 ---

[4] DVD MechanismD2D5

(S-7), *CN201, *CN301, *CN801

123456

[5] DVD Main CBA Unit D2 --------------- ---

[1] StandAssembly

[4] DVD Mechanism

[5] DVD Main CBA Unit

[2] Rear Cabinet [16] Junction-BCBA[6] Jack Holder(D)

[15] Junction-CCBA

[10] Main CBA[13] Speaker Holder

[9] Jack CBA

[14] Speaker

[3] DVD Holder

[11] Stand Holder

[7] Digital MainCBA Unit

[18] FunctionCBA

[12] LCD ModuleAssembly

[19] FrontCabinet

[8] Jack Holder(A)

[17] Junction-ACBA

[6] Jack Holder(D) D3 (S-8) ---

[7] Digital Main CBA UnitD3D5

4(S-9), (S-10), 4(S-11), 2(H-1), *CN301, *CN302, *CN303, *CN3902, Shield Box

---

[8] Jack Holder(A) D3 (S-12) ---

[9] Jack CBA D3D54(S-13), CN702, *CN861A ---

[10] Main CBA D3D57(S-14), *CN102, *CN201, *CN862A, *CN1001, *CN1002

---

[11] Stand Holder D4 2(S-15), (S-16) ---

[12]LCD Module Assembly

D4 --------------- ---

[13] Speaker Holder D4 4(S-17) ---

[14] Speaker D4 --------------- ---

[15] Junction-C CBAD4D5 Desolder ---

[16] Junction-B CBAD4D5 Desolder ---

[17] Junction-A CBAD4D5 Desolder ---

[18] Function CBAD4D5 2(S-18) ---

[19] Front Cabinet D4 --------------- ---

(1)

(2)

(3)

(4)

(5)

Step/Loc. No.

Part

Removal

Fig. No.

Remove/*Unhook/Unlock/Release/Unplug/Unclamp/

DesolderNote

5-2 A94N1DC

Note:(1) Order of steps in procedure. When reassembling,

follow the steps in reverse order. These numbers are also used as the Identification (location) No. of parts in figures.

(2) Parts to be removed or installed.(3) Fig. No. showing procedure of part location(4) Identification of parts to be removed, unhooked,

unlocked, released, unplugged, unclamped, or desoldered. P = Spring, L = Locking Tab, S = Screw, H = Hex Screw, CN = Connector* = Unhook, Unlock, Release, Unplug, or Desoldere.g. 2(S-2) = two Screws (S-2), 2(L-2) = two Locking Tabs (L-2)

(5) Refer to the following "Reference Notes in the Table."

Reference Notes1. CAUTION 1: Electrostatic breakdown of the laser

diode in the optical system block may occur as a potential difference caused by electrostatic charge accumulated on cloth, human body etc., during unpacking or repair work.To avoid damage of pickup follow next procedures.1) Short the three short lands of FPC cable with

solder before removing the FFC cable (CN201) from it. If you disconnect the FFC cable (CN201), the laser diode of pickup will be destroyed. (Fig. D2)

2) Disconnect the Connectors (CN301), and (CN801). Remove Screw (S-7) and remove the DVD Main CBA Unit. (Fig. D2)

2. Reassembly Notes of New DVD Mechanism: a. To remove the Chassis Cover, remove two

screws A as shown in Fig. D2.b. To avoid damage of the pickup unit (laser

diode), confirm that the three short lands (either of two places) are shorted out by soldering between them as shown in View A in Fig. D2.

c. Connect the FFC cables of the new DVD Mechanism to the three connectors (CN201, CN301, CN801) on the DVD Main CBA Unit.

d. After confirming that the FFC cables are securely connected to the three connectors, remove the solder from the three short lands. If the solder is not removed, the laser diode will not light and it will not be possible to read discs.

e. Insert the pin A on the Chassis Cover into the hole A on the Main Chassis as shown in Fig. D2. Then tighten two screws A to install the Chassis Cover.

3. CAUTION 2: When reassembling, confirm the FFC cable (CN201) is connected completely. Then remove the solder from the three short lands of FPC cable. (Fig. D2)

4. How to eject a disc in emergencyPress and hold [EJECT] on the unit for more than 5 seconds.

5. How to eject manually 11) Remove the Rear Cabinet.2) Rotate the gear in the direction of the arrow as

shown below.

6. How to eject manually 21) Remove the Rear Cabinet.2) To remove the DVD Main CBA Unit, remove a

screw (S-7) in Fig. D2. Do not disconnect connectors.

3) To remove the Chassis Cover, remove two screws A as shown in Fig. D2.

4) Remove a disc.

View for B

The gear is turned to the directionof the arrow.

B

5-3 A94N1DC

[2] Rear Cabinet

(S-1)

[1] Stand Assembly

(S-2)

(S-4)

(S-2)

(S-2)

(S-3)

Fig. D1

5-4 A94N1DC

Remove two screws A, then short the three short lands by soldering as shown in View for A.

View for A

Either of two places

FPC Cable

Chassis Cover

Pin A

A

Hole A

Main Chassis

Screws A

(S-5)

(S-7) (S-6)

(S-6)

A

[5] DVD Main CBA Unit

[4] DVD Mechanism

[3] DVD Holder

Fig. D2

5-5 A94N1DC

(S-8)

(S-9)

(S-9)

[9] Jack CBA

[6] Jack Holder(D)

[8] Jack Holder(A)

[10] Main CBA

[7] Digital Main CBA Unit

(S-14)

(S-11)

(S-14)

(S-12)

Shield Box

(S-13)

(H-1)(S-10)

Fig. D3

5-6 A94N1DC

(S-16)

(S-18)

(S-17)

(S-17)

[12] LCD ModuleAssembly

[11] Stand Holder

[18] Function CBA

[13] SpeakerHolder

[13] SpeakerHolder

[15] Junction-C CBA

[16] Junction -B CBA

[17] Junction-A CBA

[14] Speaker

[19] Front Cabinet

(S-15)

[14] Speaker

Fig. D4

5-7 A94N1DC

TV Cable Wiring Diagram

Main CBA

Jack CBA

CN201

CN1001

CN1002

CN3902

CN4001

CN3702

CN3701

Digital Main CBA Unit

CN102

CN101CN101A

CN702

AC CORD

CN302

CN303

CN701

CN861A

CN861B CL861

CN902 CN901

CN862A

CN301

CN101B

Junction-C CBA

Junction-A CBAJunction-B CBA

Function CBA

DVD MainCBA Unit

CN601

CN301

CN201

CN801 CN401

To DVD Mechanism

To LCD Module Assembly

To Speaker

To Speaker

CN862B CL862

To LCD Module Assembly

Fig. D5

6-1 FL9.3EA

ELECTRICAL ADJUSTMENT INSTRUCTIONSGeneral Note: CBA is abbreviation for Circuit Board Assembly.Note: Electrical adjustments are required after

replacing circuit components and certain mechanical parts. It is important to perform these adjustments only after all repairs and replacements have been completed. Also, do not attempt these adjustments unless the proper equipment is available.

Test Equipment Required1. NTSC Pattern Generator (Color Bar W/White

Window, Red Color, Dot Pattern, Gray Scale, Monoscope, Multi-Burst)

2. Remote control unit3. Color Analyzer

How to make the Service remote control unit:

[LD195SSX, LD190EM1, LD190SS1]Cut A portion of the attached remote control unit as shown in Fig. 1.

.[LD195EMX]Cut A portion of the attached remote control unit as shown in Fig. 2.

[19MD359B/F7, 19MD350B/F7]Cut A portion of the attached remote control unit as shown in Fig. 3.

How to set up the service mode:Service mode:1. Use the service remote control unit.2. Turn the power on.3. Press the service button on the service remote

control unit. The following screen appears.

Fig. 1

service button

A

Fig. 2

service button

A

Fig. 3

service button(There is a button under the plastic housing.)

A

Code : Pic code : MIPS :

***********-*** **-***-**-*****-***Push 0key

Tuner : Safety :

****-*****-****safety_Non

"*" differs depending on the models.

6-2 LC7NEA

1. Purity Check ModeThis mode cycles through full-screen displays of red, green, blue, and white to check for non-active pixels.1. Enter the Service mode.2. Each time pressing [7] button on the service

remote control unit, the display changes as follows.

2. VCOM Adjustment

1. Operate the unit for more than 20 minutes.2. Set the color analyzer and bring the optical

receptor to the center on the LCD-Panel surface after zero point calibration as shown above.Note: The optical receptor must be set perpendicularly to the LCD Panel surface.

3. Enter the Service mode. 4. Press [3] button on the service remote control unit.5. Press [CHANNEL UP/DOWN] buttons on the

service remote control unit so that the color analyzer value becomes minimum.

[7] button

Note:When entering this mode, the default setting is White mode.

Purity Check Mode

[7] button

Red mode

Green mode

Blue mode

Black mode

[7] button

White mode

[7] button

[7] button

White 20% mode[7] button

Test Point Adj. Point

Screen [CHANNEL UP/DOWN ] buttonsM. EQ. Spec.

Color analyzer See belowFigure

Color Analyzer

To avoid interference from ambinent light, this adjustment should be performed in a dark room.

L = 3 cm

Perpendicularity

6-3 LC7NEA

The White Balance Adjustment should be performed when replacing the LCD Panel or Digital CBA.

3. White Balance AdjustmentPurpose: To mix red, green and blue beams correctly for pure white. Symptom of Misadjustment: White becomes bluish or reddish.

1. Operate the unit for more than 20 minutes.2. Input the White Raster(70%=70IRE, 40%=40IRE).

3. Set the color analyzer to the CHROMA mode and bring the optical receptor to the center on the LCD-Panel surface after zero point calibration as shown above.Note: The optical receptor must be set perpendicularly to the LCD Panel surface.

4. Enter the Service mode. Press [VOLUME DOWN] button on the service remote control unit and select C/D mode.

5. [CUTOFF]Press [1] button to select COR for Red Cutoff adjustment. Press [3] button to select COB for Blue Cutoff adjustment.[DRIVE]Press [4] button to select DR for Red Drive adjustment. Press [6] button to select DB for Blue Drive adjustment.

6. In each color mode, press [CHANNEL UP/DOWN] buttons to adjust the values of color.

7. Adjust Cutoff and Drive so that the color temperature becomes 12000K (x= 0.272 / y= 0.278 0.005).

Test Point Adj. Point Mode Input

Screen[VOLUME DOWN]button

[VIDEO1]C/D

White Raster (APL 70%)

or(APL 40%)

M. EQ. Spec.Pattern Generator,

Color analyzerx= 0.272 0.005y= 0.278 0.005

Figure

Color AnalyzerL = 3 cm

Perpendicularity

INPUT: WHITE 70%, 40%

To avoid interference from ambinent light, this adjustment should be performed in a dark room.

40%=40IRE 70%=70IRE100IRE100IRE

0IRE 0IRE

INPUT SIGNAL

LowLight

HightLight

7-1 A94N1INT

HOW TO INITIALIZE THE LCD TV/DVDThe purpose of initialization is to place the set in a new out of box condition. The customer will be prompted to select a language and program channels after the set has been initialized.To put the program back at the factory-default, initialize the LCD TV/DVD using the following procedure.

< DVD Section >1. Turn the power on.2. To enter the service mode, press the service

button on the service remote control unit. - To cancel the service mode, press [POWER]

button on the service remote control unit.3. To put the LCD TV/DVD into the DVD mode, press

[CH RETURN] or [PREV CH] on the remote control unit.

4. To put the LCD TV/DVD into the Flash clear mode, press [INPUT SELECT] or [SOUCE] buttons on the remote control unit in that order within five seconds.The following screen appears.

When OK appears on the screen, the factory default will be set.

5. To exit this mode, press[CHANNEL UP/DOWN] button to go to TV mode, or press [POWER] button to turn the power off.

Note: The name of buttons may vary with the brand of unit.

< LCD TV Section >1. Turn the power on.2. To enter the service mode, press the service

button on the service remote control unit. - To cancel the service mode, press [POWER]

button on the service remote control unit.3. Press [INFO] button on the service remote control

unit to initialize the LCD television.4. "INITIALIZED" will appear in the upper right of the

screen. "INITIALIZED" color will change to green from red when initializing is complete.

Flash Memory Clear : OK

CHUCKING ON

8-1 A94N1FW

FIRMWARE RENEWAL MODE< DVD Section >1. Turn the power on and press [EJECT] button on

the remote control unit to put the LCD TV/DVD into DVD mode. Then remove the disc.

2. To put the LCD TV/DVD into F/W version up mode, press [9], [8], [7], [6], and [MODE] buttons on the remote control unit in that order.Fig. a appears on the screen.

Fig. a Version Up Mode Screen3. Insert the disc for version up into the disc slot.4. The LCD TV/DVD enters the F/W version up mode

automatically. Fig. b appears on the screen. Make sure to insert the proper F/W for the state of this model.

Fig. b Programing Mode ScreenThe appearance shown in (*1) of Fig. b is described as follows:

5. After programming is finished, the disc will be ejected automatically. Fig. c appears on the screen and the checksum will be shown in (*2).

Fig. c Completed Program Mode ScreenAt this time, no button is available.

6. Remove the disc.7. Unplug the AC cord from the AC outlet. Then plug

it again.8. Press [EJECT] button on the remote control unit to

put the LCD TV/DVD into DVD mode again.9. Press [1], [2], [3], [4], and [INFO] buttons on the

remote control unit in that order. Fig. d appears on the screen.

Fig. d10. Press [CLEAR] button on the remote control unit.

Fig. e appears on the screen.

Fig. eWhen OK appears on the screen, the factory default will be set. Then the firmware renewal mode is complete.

11. To exit this mode, press [CHANNEL UP/DOWN] button to go to TV mode, or press [POWER] button to turn the power off.

F/W Version Up Mode Model No : ******VERSION : *.**

Please insert a DISCfor F/W Version Up.

EXIT: SELECT

"*******" differs depending on the models.

VERSION : ************.***Reading...


"*******" differ depending on the models.

(*1)

AppearanceNo. StateReading... Sending files into the memoryErasing... Erasing previous version data Programming...

123 Writing new version data

VERSION : ************.***CompletedSUM : ****


"*******" differ depending on the models.

(*2)

MODEL : ****** Version : *.** Region : *

EXIT: SELECTEEPROM CLEAR : CLEAR


MODEL : ****** Version : *.** Region : *

EEPROM CLEAR : OK

EXIT: SELECTEEPROM CLEAR : CLEAR


8-2 A94N1FW

< LCD TV Section >Equipment Requireda. USB memoryb. Remote Control Unit

Firmware Update ProcedureNote: There are two states (the User Upgrade and

the Factory Upgrade) in firmware update.

The identification of User Upgrade and Factory Upgrade are done by the filename.1. Turn the power off and unplug the AC Cord.2. Insert the USB memory to the USB port as shown

below.

3. Plug the AC cord in the wall outlet and turn the power on.

4. The update will start and the following will appear on the screen.

Note: If the above screen isnt displayed, repeat from step 1.

The appearance shown in *1 is described as follows.

5. When the firmware update is completed, the following will appear on the screen.

Unplug the AC cord and kindly remove the USB memory from the USB port. Plug the AC cord in the wall outlet again and turn the power on.

Note:When the Factory Upgrade is used, after restarting TV, shift to initial screen menu in service mode. "INITIALIZED" will appear on the upper right of the screen. "INITIALIZED" color will change to green from red when initializing is complete.

User Upgrade Upgrade the firmware only. The setting values are not initialized.

Factory upgrade Upgrade the firmware and initialize the setting values.

Rear Cabinet

USB Memory

USB port

Software upgrade in progress. Please wait.Do not remove the USB device or turn the TV offwhile upgrade is in progress.

Software Upgrade

Downloading...

0%*1

Appearance State

Downloading... Downloading the firmware from the USB memory.

Writing... Writing the downloaded firmware in flash memory.Checking... Checking the new firmware.

Software Upgrade

The software upgrade is completed.Remove USB storage device, unplug and replug power code.

9-1 A94N1TR

TROUBLESHOOTING[ Power Supply Section ]

The power cannot be turned on.

The fuse blows out.

FLOW CHART NO.1

FLOW CHART NO.2

Is normal state restored when once unpluggedpower cord is plugged again several seconds?

Check if there is any leak or short-circuiting on theprimary circuit component, and service it if defective.(D601, D602, D603, D604, Q601, Q602, T601)

Yes

No

Yes

Is the fuse (F601) normal? See FLOW CHART No.2

No

Yes

Is the INV+31V line voltage normal?No

Check each rectifying circuit of the secondarycircuit and service it if defective.

Check the presence that the primary componentis leaking or shorted and service it if defective.

Check the presence that the rectifying diode or circuit is shorted in each rectifying circuit of secondary side, and service it if defective.

After servicing, replace the fuse.

When the output voltage fluctuates.FLOW CHART NO.3

Does the photocoupler circuit on the secondary side operate normally?

No

Yes

Check IC601, D633, Q631 and their periphery circuit, and service it if defective.

When buzz sound can be heard in the vicinity of power circuit.FLOW CHART NO.4

Check if there is any short-circuit on the rectifying diode and the circuit in each rectifying circuit of the secondary side,and service it if defective. (IC631, IC901, Q201, Q205, Q206, Q634, Q635, Q636, Q637, Q640, Q641, Q643, Q901, Q903, Q904, D631, D632, D636, D638, D639, D640, D641, D643)

Check D667, R655 and their periphery circuit, and service it if defective.

INV+31V is not output.FLOW CHART NO.5

Is approximately +31V voltage supplied to thecathode of D632?

No

Yes

Check C632, D632, D633 and their periphery circuit, and service it if defective.

Check IC601, D608, D610 and their periphery, circuit and service it if defective.

9-2 A94N1TR

Check Q202, Q203, D203, P-ON-H1 line and their periphery circuit, and service it if defective.

PANEL+24.5V is not output.FLOW CHART NO.6

Is approximately +30V voltage supplied to the collector of Q205?

No

Yes

See FLOW CHART No.5

Replace Q201.

Is approximately +13V voltage supplied to thebase of Q201?

Yes

NoCheck Q202, Q203, D201, D202, D210 and theirperiphery circuit, and service it if defective.

No

PANEL+13V is not output.FLOW CHART NO.7

Is approximately +15V voltage supplied to thecollector of Q201?

Yes


P-ON+7V is not output.FLOW CHART NO.8


Check C641, D641 and their periphery circuit, and service it if defective.

Yes

No

Check if there is any leak or short-circuit onthe loaded circuit, and service it if defective.

See FLOW CHART No.8

P-ON+5V is not output. (PANEL+13V is outputted normally.)FLOW CHART NO.9

Is approximately +6.8V voltage supplied to thecollector of Q635?

Is approximately +6V voltage supplied to the base of Q635 and the base of Q636?

NoYes

Yes

Check D659 and their periphery circuit, and service it if defective.

No

Replace Q635 and Q636.

9-3 A94N1TR

See FLOW CHART No.8

TUNER+5V is not output. (PANEL+13V is outputted normally.)FLOW CHART NO.10


Is approximately +6V voltage supplied to the base of Q637?

NoYes

Yes


No

Replace Q637.

P-ON+3.3V(PANEL+3.3V) is not output.FLOW CHART NO.12


Is the "H" signal (approximately +3.5V) inputted to the base of Q640?

NoYes

Yes

Check C639, D639 and their periphery circuit, andservice it if defective.

Check Q638, Q639, P-ON-H2 line and their periphery circuit, and service it if defective.

No

No

EV+3.3V is not output.FLOW CHART NO.13


Yes

Replace Q640.

Check Q903, D905 and their periphery circuit, and service it if defective.

P-ON+3V is not output.FLOW CHART NO.11


Yes

No

Check if there is any leak or short-circuit onthe loaded circuit, and service it if defective.



9-4 A94N1TR

EV+9V is not output. (PANEL+13V is outputted normally.)FLOW CHART NO.15


Yes

No

No

DVD-ON+3.3V is not output.FLOW CHART NO.14


Yes

Check Q904, D906, and their periphery circuit, and service it if defective.

Check Q905, D901 and their periphery circuit, and service it if defective.




Is approximately +4V voltage supplied to Pin(3) of IC901?

Yes

NoCheck Q901, Q902, DVD-MAIN PWR line and their periphery circuit, and service it if defective.

No

EV+1.2V is not output.FLOW CHART NO.16

Is approximately +5V voltage supplied to theemitter of Q901?

Yes

Replace IC901.

P-ON+9V is not output. (PANEL+13V is outputted normally.)FLOW CHART NO.17


Is approximately +10V voltage supplied to thebase of Q641?

NoYes

Yes



No

Replace Q641.

9-5 A94N1TR

Is approximately +5V voltage supplied to Pin(1) of IC631?

Yes

NoCheck Q634, D650 and their periphery circuit, andservice it if defective.

See FLOW CHART No.5No

AL+3.3V is not output.FLOW CHART NO.18


Yes

Replace IC631.


Check Q202, Q203, D204, P-ON-H1 line and their periphery circuit, and service it if defective.

Replace Q206.

Is approximately -8V voltage supplied to thebase of Q206?

Yes

No

No

LCD-7.1V is not output.FLOW CHART NO.19

Is approximately -9V voltage supplied to theAnode of D636?

Yes

9-6 A94N1TR

[ Video Signal Section ]

No

Is the "L" pulse sent out Pin(1) terminal of remote control receiver (RS101) when the infrared remote control is activated?

Check the line between Pin(1) terminal of remote control receiver(RS101) and Pin(25) of CN301, and service it if defective.

Yes

Is the "L" pulse supplied to Pin(25) of CN301?

Yes

Is 3.3V voltage supplied to Pin(2) terminal of theremote control receiver (RS101)?

No

FLOW CHART NO.2

Operation is possible from the unit.

Check AL+3.3V line and service it if defective.

NoReplace the remote control receiver(RS101) or the remote control unit.

Yes

Replace Digital Main CBA Unit.

When pressing each switches (SW104~SW109, SW951~SW953) do the voltage of Pin(29) of CN302 and Pin(2) of CN303 increase?

Yes

The key operation is not functioning.FLOW CHART NO.1

Are the contact point and installation state of the key switches (SW104~SW109, SW951~SW953) normal?

Re-install the switches (SW104~SW109, SW951~SW953) correctly or replace the poor switch.

Check the switches (SW104~SW109, SW951~SW953) and their periphery, and service it if defective.

Yes


No

No

No operation is possible from the remote control unit.

Picture does not appear normally.(Video input)FLOW CHART NO.3

Are the video signal inputted to Pin(4) of CN302?

Yes

Check the line between Pin(4) of CN302 and JK752, and service it if defective.

No

Replace Digital Main CBA Unit or LCD ModuleAssembly.

9-7 A94N1TR

Picture does not appear normally.(S-Video input)FLOW CHART NO.5

Are the video signal outputted to Pin(6, 8) of CN302? Check the line between Pin(6, 8) of CN302 and JK751, and service it if defective.

Check the line between Pin(26, 28) of CN302 andPin(10, 11) of TU302, and service it if defective.

Yes

No

No

Picture does not appear normally.(Tuner input)FLOW CHART NO.4

Are the DIF signal inputted to Pin(26,28) of CN302?

Yes



Pin(6): S-VIDEO-CPin(8): S-VIDEO-Y

Picture does not appear normally.(Y/Pb/Pr input)FLOW CHART NO.6

Are the video signal inputted to Pin(15, 17, 19) of CN302?

Check the line between Pin(15, 17, 19) of CN302 and input terminals(JK731, JK732, JK733), and service it if defective.

Yes

No


Pin(15): VIDEO-YPin(17): VIDEO-PbPin(19): VIDEO-Pr

Are the video signal inputted to Pin(1, 3, 5) of CN902? Replace DVD Main CBA Unit.No

Picture does not appear normally.(DVD PB)FLOW CHART NO.7


Pin(9) : DVD-YPin(11) : DVD-PbPin(13) : DVD-Pr

Yes

9-8 A94N1TR

[ Audio Signal Section ]

Check SP861,SP862 and their periphery circuit,and service it if defective.

Are the audio(L/R) signals inputted to Pin(1, 9)of IC801?

Yes

Yes

Yes

Audio is not outputted normally.(Audio input)FLOW CHART NO.1


Check the line between Pin(2, 15) of IC771 and input terminal(JK753, JK754), and service it if defective.

No

No

Are the audio(L/R) signals outputted to Pin(4, 6)of IC801?

Check IC801 and their periphery circuit, and service it if defective.

No

Yes

Are the audio(L/R) signals inputted to Pin(6, 8) of CN301?


Check the line between Pin(1, 7) of IC803 and Pin(1, 9) of IC801, and service it if defective.


No

Yes

Check the line between Pin(6, 8) of CN301 and Pin(3, 5) of IC803, and service it if defective.


No

Yes

Replace IC803

No



Yes

Yes

Yes

Audio is not outputted normally.(Component Audio input)FLOW CHART NO.2



No

No



No

Yes





No

Yes



No

Yes

Replace IC803

No

9-9 A94N1TR



Yes

Yes

Yes

Audio is not outputted normally.(Tuner input)FLOW CHART NO.3

Are the DIF signals outputted to Pin(26, 28) of CN302? Check TU302 and their periphery circuit, and service it if defective.

No

No



No

Yes





No

Yes



No

Yes

Replace IC803

No



Yes

Yes

Yes

Audio is not outputted normally.(HDMI Audio input)FLOW CHART NO.4



No

No



No

Yes





No

Yes



No

Yes

Replace IC803

No

9-10 A94N1TR



Yes

Yes

Yes

Audio is not outputted normally.(PC Audio input)FLOW CHART NO.5


Check the line between Pin(1, 12) of IC771 and input terminal(JK711), and service it if defective.

No

No



No

Yes





No

Yes



No

Yes

Replace IC803

No

10-1

BLOCK DIAGRAMSSystem Control Block Diagram

A94N1BLS

AC18

KEY

SWIT

CH

IC33

01(M

AIN

MICR

O C

ONT

ROLL

ER)

DIG

ITA

L M

AIN

CBA

UNI

T

FUNC

TIO

N CB

A

MA

IN C

BA

CN10

1BREM

OTE

SENS

OR

RS1

01

AL+3

.3V

D10

4PO

WER

STAN

DBY

D10

3

D95

0DV

D

LED

14

4

CN10

1AR

EMOT

E2

2P-

ON-

H15

5

CN30

3CN

4001

CN30

2CN

3702

CN37

02CN

302

CLKO

UTCL

KIN

X310

125

MH

zO

SCN

1N

2

SCL

SDA

4 5

TU30

2(T

UNER

UNI

T)

TO

INVE

RTER

BLO

CK

DIA

GRA

M

TO

POW

ER S

UPPL

Y BL

OCK

DIA

GRA

M

DVD

-SCL

KD

12D

11 F5 AB8

AB17

DVD

-CS

E12

AB14

C12

PROT

ECT3

AE5

VCO

M-P

WM

AC14

PROT

ECT2

AD4

PROT

ECT1

AD5

KEY-

IN1

AC5

DVD

-LED

E5

KEY-

IN2

AD6

BACK

LIG

HT-SW

AB16

LED

1F1

E1 E2

P-O

N-H2

AB13

REM

OTE

R22

P-O

N-H1

PROT

ECT2

PROT

ECT1

P-O

N-H2

P-O

N-H1

R23

JUNC

TIO

N -A

CBA

CN10

1

KEY-

IN1

66

KEY

SWIT

CH

CN10

2

CN30

1

Q171

Q400

1

Q172

CN37

01

AB23

BACK

LIG

HT-AD

J

IC31

01 (M

EMOR

Y)

SCK SI SO

AB25

AB24

AC25

AC24

6 5 2 1E1

13

AC19

SCL

SDA

CN30

3CN

4001

CN40

1CN

901

CN60

1CN

902

CN30

1CN

3701

TO

DVD

SYS

TEM

CO

NTRO

L / S

ERVO

BLO

CK D

IAG

RAM

DVD

MA

IN C

BA U

NIT

CS WP

SCK

SIN

SOUT

CS WP

KEY-

IN2

77

DVD

-LED

88

DVD

-SDA

TA

U23

LED

-CO

NTDV

D-P

-ON

DVD

-REM

OTE

DVD

-DIS

C-IN

DVD

-DIS

C-O

UTDV

D-A

UDIO

-MUT

E

DVD

-SCL

KDV

D-C

S

DVD

-SDA

TA

DVD

-P-O

NDV

D-R

EMOT

E

DVD

-DIS

C-IN

DVD

-DIS

C-O

UT

DVD

-AUD

IO-M

UTE

BUFF

ER

IC20

1,Q2

07,

Q208

,Q20

9D

RIV

E

66

DVD

-P-O

N16

16LE

D-C

ONT

77

DVD

-REM

OTE

88

DVD

-SDA

TA13

13DV

D-S

CLK

1111

DVD

-CS

99

DVD

-DIS

C-IN

1515

DVD-

DISC

-OUT

2525

DVD-

AUDI

O-MU

TEAB

10DV

D-M

AIN

-PW

R5

5DV

D-M

AIN-

PWR

2222

SCL

2121

SDA

1111

PROT

ECT1

1515

PROT

ECT2

55

PROT

ECT3

2929

VCO

M-P

WM

2626

BACK

LIGHT

-SW

2828

BACK

LIGHT

-AD

J

KEY-

IN1

2929

P-O

N-H1

99

REM

OTE

2525

LED

127

27P-

ON-

H21

1

KEY-

IN2

22

DVD

-LED

33

LED

14

4

REM

OTE

22

P-O

N-H1

55

KEY-

IN1

66

KEY-

IN2

77

DVD

-LED

88

2626

DVD

-P-O

N

LED

-CO

NT2

2LE

D-C

ONT

2525

DVD

-REM

OTE

2424

DVD

-SDA

TA21

21DV

D-S

CLK

2222

DVD

-CS

2323

DVD

-DIS

C-IN

33

DVD-

DISC

-OUT

413

DVD-

AUDI

O-MU

TE

DVD

-MAI

N-P

WR

TO DV

D D

IGIT

ALSI

GNA

L PR

OCE

SSBL

OCK

DIA

GRA

M

TO AU

DIO

BLO

CK

DIA

GRA

MAU

DIO

-MUT

E

INPU

T0IN

PUT1

U6 V6

SHD-

SPD-

ENDV

D-S

PD-E

N

AUD

IO-M

UTE

INPU

T0IN

PUT1

SHD-

SPD-

ENDV

D-S

PD-E

N

AB9

PROT

ECT3

BACK

LIGHT

-SW

BACK

LIGHT

-AD

J

VCO

M

10-2 A94N1BLV

Video Block Diagram

DIG

ITA

L M

AIN

CBA

UNI

T

COM

PONE

NT-Y-

IN

COM

PONE

NT-Pb

-IN

COM

PONE

NT-Pr

-IN

JK73

1

JK73

2

JK73

3

VID

EO-IN

44

S-VI

DEO

-C-IN

66

S-VI

DEO

-Y-IN

88

S-VI

DEO

-SW

55

COM-

VIDE

O-Y-I

N15

15CO

M-VID

EO-P

b-IN

1717

COM-

VIDEO

-Pr-IN

1919

JACK

CBA

CN70

2CN

701

VID

EO-IN

27S-

VIDE

O-C

-IN28

S-VI

DEO

-Y-IN

26

27 28 26JK

751

S-VI

DEO

-IN

CY

JK75

2VI

DEO

-IN

S-VI

DEO-

SW-IN

1919

COM-

VIDE

O-Y-

IN20

20CO

M-VI

DEO-

Pb-IN

1818

COM-

VIDE

O-Pr

-IN16

16

MA

IN C

BA

TU30

1

DIF

-OUT

111

DIF

-OUT

210

(TUN

ER U

NIT) I

F-AG

C9

CN30

2CN

3702

DIF

-OUT

126

26

IF-A

GC

2424

DIF

-OUT

228

28

TO DV

D D

IGIT

ALSI

GNA

L PR

OCE

SSBL

OCK

DIA

GRA

M

DIF

-OUT

1D

IF-O

UT2

IF-A

GC

CN30

2CN

3702

VID

EO-IN

S-VI

DEO

-C-IN

S-VI

DEO

-Y-IN

S-VI

DEO

-SW

COM-

VIDE

O-Y-I

N

COM-

VIDEO

-Pr-IN

COM-

VIDEO

-Pb-I

N

CN60

1CN

902

DVD

MA

IN C

BA U

NIT

DVD

-Pb

DVD

-Y11

3DV

D-P

b

DVD

-Pr

131

DVD

-Pr

95

DVD

-Y

CN40

01

JK37

03PC

-RG

BIN

CN30

3

DVD

-Pb

DVD

-Pr

2020

DVD

-Pb

DVD

-Y22

22DV

D-Y

1818

DVD

-Pr

TO D

IGIT

ALSI

GNA

L PR

OCE

SSBL

OCK

DIA

GRA

M

WF1

WF2

WF3

WF9

WF4

WF5

WF6

WF8

WF1

0

VID

EO S

IGNA

LA

UDIO

SIG

NAL

1 2 3

VGA-

R-IN

VGA-

G-IN

VGA-

B-IN

10-3

Audio Block Diagram

A94N1BLA

IC77

1(A

UDIO

SEL

ECTO

R)

HD

MI-

AUDI

O(L)

-IN

HD

MI-

AUDI

O(R

)-IN

JK72

1

JK72

2

COM

PONE

NT-

AUDI

O(L)

-IN

COM

PONE

NT-

AUDI

O(R

)-IN

JK74

1

JK74

2

PC-A

UDIO

-INJK

711

2 4 1 5 15 11 12 14JACK

CBA

AUDI

O(L)

-IN AU

DIO

(R)

-INJK

753

JK75

4

CN37

02CN

302

AUDI

O(L)

1313

AUDI

O(R

)11

11CN

702

CN70

1

CN70

2CN

701

AUDI

O(L)

1313

AUDI

O(R

)15

15CN

3702

CN30

2IN

PUT1

1010

INPU

T012

12 CN3

701

CN30

1

AMP(

L)-OU

T6

6AM

P(R)

-OUT

88

MA

IN C

BAJU

NCTI

ON-

B CB

AD

IGIT

AL

MA

IN C

BA U

NIT

8

4 6

IC80

1 (A

UDIO

AM

P)

1 9

MUT

E CO

NTRO

L

CL86

2CN

862B

CN86

2ASP

862

SPEA

KER

R-C

H

DR

IVE

CN30

2CN

3702

CN30

3CN

4001

AUDI

O-M

UTE

2020

JK84

1D

IGIT

ALAU

DIO

-OUT

(COA

XIAL

)Q8

41

Q771

Q722

BUFF

ER

SPDI

F2

2

SPDI

F23

23

DVD

-SPD

IF28

28

Q801

CONT

ROL

LOG

IC

3

109

13

IC80

3(O

P AM

P)

13

75

DR

IVE

CN60

1CN

902

DVD

-AUD

IO(L)

59

DVD

-AUD

IO(R

)3

11DV

D-S

PDIF

113

IC90

2 (O

P AM

P)

75

13

IC38

01(D

/A C

ONVE

RTER

)

D/A CO

NVER

TER

15148 7 6 5

(L-CH

)(R

-CH)

AUDI

O(L)

AUDI

O(R

)

CN40

01CN

303

DVD

-AUD

IO(L)

2424

DVD

-AUD

IO(R

)26

26

DVD

-AUD

IO(L)

DVD

-AUD

IO(R

)TO

DIG

ITAL

SIG

NAL

PRO

CESS

BLO

CKD

IAG

RAM

TO

DIG

ITAL

SIG

NAL

PRO

CESS

BLO

CKD

IAG

RAM

INPU

T1

DVD

-AUD

IO(L)

DVD

-AUD

IO(R

)DV

D-S

PDIF

LRCL

KBC

LKAD

ATA0

ACLK

SHD-

SPDI

F

INPU

T0AU

DIO

-MUT

E

TO

SYST

EMCO

NTRO

LBL

OCK

DIA

GRA

M

TO

SYST

EMCO

NTRO

LBL

OCK

DIA

GRA

M

IC33

03

(BUF

FER

GAT

E)

4

1

2

IC33

02

(BUF

FER

GAT

E)

4

1

2

AUD

IO S

IGNA

L

TO DV

D

DIG

ITAL

SIG

NAL

PR

OCE

SSBL

OCK

D

IAG

RAM

DVD

MA

IN C

BA U

NIT

WF1

1

WF1

3W

F12

SHD-

SPD-

ENDV

D-S

PD-E

N

WF7

BUFF

ERQ9

07

BUFF

ERQ7

73 BUFF

ERQ7

74

Q906

BUFF

ER

INPU

T124

24IN

PUT0

2222

1 2SP

(R)

1,2

1,2

SP-G

ND3,

43,

4

HEAD

PHON

E(R)3

,43,

4HE

ADPH

ONE(L

)9,1

09,

10SP

(R)

1,2

1,2

JUNC

TIO

N-C

CBA

CL86

1CN

861B

CN86

1ASP

861

SPEA

KER

L-CH

1 2SP

(L)1,

21,

2SP

-GND

3,4

3,4

JK85

1H

EAD

PHO

NEJA

CK

10-4

Digital Signal Process Block Diagram

A94N1BLD

DIG

ITA

L M

AIN

CBA

UNI

TIC

3301

(DIG

ITAL

SIG

NAL

PRO

CESS

)IC

3901

(TIN

ING

CONT

ROLL

ER)

LCD

MO

DULE

ASSE

MBL

YCN

3902

LLV1

(+)21

LLV1

(-)20

LLV0

(+)23

LLV0

(-)22

LLV2

(+)19

LLV2

(-)18

LLV3

(+)13

LLV3

(-)12

LLV4

(+)11

LLV4

(-)10

LLV5

(+)9

LLV5

(-)8

LLVC

LKP

16LL

VCLK

N15

TP6

POL

5CP

V4

OE1

3ST

V1

48 47 46 45 44 43 38 37 36 35 34 33 42 41 63 64 30 31 32

8 7 10 9 12 11 16 15 14 13

DATA

PRO

CESS

ING

FRC

LIN

E BU

FFER

GAM

MA

CORR

ECTO

R

LVD

SR

X

LVD

S O

UTPU

T

DATA

INPU

T LA

TCH

AD23

AD24

AE23

AF23

AF22

AE22

AD21

AD22

AF24

AE24

LVD

STX

DIG

ITAL

SIG

NAL

PRO

CESS

A/D

CONV

ERTE

R

S-VI

DEO

-Y-IN

SW

V1 U2U1

S-VI

DEO

-C-IN

U3

VID

EO-IN

VGA-

R-IN

VGA-

G-IN

VGA-

B-IN

V3T3T1T2

COM

-VID

EO-P

r-IN

COM

-VID

EO-P

b-IN

COM

-VID

EO-Y

-IN

Y1 W2

W1

DVD

-Pr

DVD

-Pb

DVD

-Y

AA3

IF-A

GC

HD

MI-I

N1

HD

MI-I

N2

JK37

01

TMD

S-D0

(+)TM

DS-

D0(-)

TMD

S-D1

(+)TM

DS-

D1(-)

TMD

S-D2

(+)TM

DS-

D2(-)

SDA

SCL

7 9 4 6 1 3 10 12 16 15 7 9 4 6 1 3 10 12 16 15

JK37

02

TMD

S-D0

(+)TM

DS-

D0(-)

TMD

S-D1

(+)TM

DS-

D1(-)

TMD

S-D2

(+)TM

DS-

D2(-)

TMD

S-CL

OCK

(+)TM

DS-

CLO

CK(-)

SDA

SCL

A9 B9 C8 C9 B8 A8 B10

A10

A11

B11

A5 B5 C4 C5 B4 A4 B6 A6 A7 B7

TMD

S-CL

OCK

(+)TM

DS-

CLO

CK(-)

DEM

ODU

LATO

R/M

PEG

DEC

ODE

RAE

2

AF7

AUDI

O I/

FTO

AU

DIO

BLO

CK D

IAG

RAM

ACLK

BCLK

LRCL

K

ADAT

A0SH

D-SP

DIF

AD9

AD12

AD10

AD11

AC10

DATA

(0-15

)

ADD

ESS(

0-12)

IC32

01

A13-1

5,A18

,A2

1-23,B

13-15

,B1

7,B19

-23C1

5,C17

-19,

C23,C

24,D

14,

D15,D

17-19

,D2

2,D23

B1,B

9,C2,C

8,D1

,D3,D

7,D9,

F1,F9

,G2,G

8,H1

,H3,H

7,H9

M2,M

3,M7,M

8,N2

,N3,N

7,N8,

P2,P

3,P7,P

8,R2(

DDR2

SDR

AM)

HD

MI

I/F

HD

MI-I

N3

WIT

H H

DM

I-IN

37 9 4 6 1 3 10 12 16 15

JK37

04

TMD

S-D0

(+)TM

DS-

D0(-)

TMD

S-D1

(+)TM

DS-

D1(-)

TMD

S-D2

(+)TM

DS-

D2(-)

TMD

S-CL

OCK

(+)TM

DS-

CLO

CK(-)

SDA

SCL

B1 B2 C1 C2 D1 D2 A1 A2 A3 B3

AUDI

OD

ECO

DER

DIF

-OUT

1D

IF-O

UT2

IF-A

GC

TO VI

DEO

BLO

CK D

IAG

RAM

TO VI

DEO

BLO

CK D

IAG

RAM

VID

EOD

ECO

DER

AF2

S-VI

DEO

-SW

C6S-

VIDE

O-S

W

M2

AUDI

O(R

)M

1AU

DIO

(L)L2

DVD

-AUD

IO(R

)L1

DVD

-AUD

IO(L)

VID

EO S

IGNA

LA

UDIO

SIG

NAL

10-5

Inverter Block Diagram

A94N1BLINV

MA

IN C

BA

PROT

ECT3

BACK

LIGHT

-AD

JBA

CKLI

GHT-

SWTO

SYS

TEM

CONT

ROL

BLO

CK

DIA

GRA

M

IC10

01(P

WM

CONT

ROL)

BACK

LIG

HT1 2

CN10

02

Q100

1,

Q100

7,

Q101

6

Q101

4

Q100

5

Q100

4,Q1

006,

Q1

008,

Q101

2Q1

002,

Q101

1 Q102

3,Q1

024

Q102

2

DR

IVE

Q101

0,

Q101

7,

Q101

8

DR

IVE

OSC

PWM

CONT

ROL

LOGI

C

VCC

DCT

CURR

ENT

CONT

ROL

SWITC

H

CURR

ENT

CONT

ROL

SWITC

H

Q100

9OV

ER VO

LTAG

EPR

OTEC

TOR

Q101

5OV

ER VO

LTAG

EPR

OTEC

TOR

11 8

56

1534

VREF

1412 16 2 1

SW+1

6V

SW

SW+1

6V

Q101

9

Q100

3

LCD

MO

DULE

ASS

EMBL

Y

T100

2

4 1 3

78 6 5

2BA

CKLI

GHT

1 2

CN10

01

IC10

02

(COM

PARA

TOR) 6

75 2 3

1

PAN

EL+1

5V

INV+

31V

Q100

5CU

RREN

TCO

NTRO

LSW

ITCH

LD19

0EM

1,/1

9MD3

50B/

F7/L

D190

SS1

LD19

5SSX

,LD

195E

MX,

19M

D359

B/F7

10-6

Power Supply Block Diagram

A94N1BLP

HOT

COLD

MA

IN C

BA

HO

T CI

RCUI

T. B

E CA

REFU

L.

Q602

SWIT

CHIN

GCO

NTRO

L

14 3

2

IC60

1

T601

2LI

NE

FILT

ER

L601

AC60

1AC

CO

RD

BRID

GE

REC

TIFI

ER

D60

1- D

604

43

11 15 10 9 16 14 13 12

7 6

FEED

BACK

Q601

SWIT

CHIN

G

Q631

CN20

1

CN40

1

CN30

1CN

3701

Q202

,Q20

3SW

ITCH

ING

Q206

SW-7.

1V

Q402

Q201

,D20

2SW

+13V

Q904

,D90

6SW

+3.3

V

Q903

,D90

5SW

+3.3

V

Q634

IC63

1+

3.3V

REG

.2

3

Q633

Q638

,Q63

9

Q635

,Q63

6SW

+5V

Q637 SW

+5VQ6

41 SW+9

V

Q640

,D66

2SW

+3.3

V

IC90

1+

1.2V

REG

.

4A/1

25V

F601

4A

/125

V

P-O

N-H1

TO SY

STEM

CO

NTRO

L BL

OCK

DIA

GRA

M

P-O

N-H2

VCO

M

+5V

REG

.

PRO

TECT

2

DVD

-MAI

N-P

WR

PRO

TECT

1

SWIT

CHIN

G

AL+3

3VP-

ON+

5V

AL+3

.3V

SP+1

4VTU

NER+

5V

P-O

N+9V

P-O

N+3.

3VPA

NEL

+13V

19,2

021

,22

13,1

4

P-O

N+3V

P-O

N+7V

AL+3

.3V

P-O

N+3.

3VP-

ON+

5V

AL+3

.5V

DVD-

ON+3

.3VEV

+3.3

VDV

D-ON

+5V

EV+9

VEV

+1.2

V

LCD

MO

DULE

ASS

EMBL

Y

DVD

MA

IN C

BA U

NIT

DIG

ITA

L M

AIN

CBA

UNI

T

PAN

EL-7

.1V

8

P-O

N+3.

3V19

,20

P-O

N+3.

3V6,

7PA

NEL

+24.

5V4

PAN

EL+1

3V2,

3

AL+3

.3V

21,2

21610

P-O

N+7V

16P-

ON+

3V10

P-O

N+5V

13,1

4

Q205

SW+2

4.5V

Q901

,Q90

2SW

ITCH

ING

10 11,1

2

6~8

4,59

DVD

-ON+

5V10

EV+9

V11

,12

1AL

+3.3

V1

EV+3

.3V

6~8

EV+1

.2V

4,5

DVD

-ON+

3.3V

9

CN90

1

Q905 SW

+9V

VCO

M10

CAUT

ION

!Fi

xed

volta

ge (o

r Auto

volta

ge se

lectab

le) po

wer s

upply

circu

it is u

sed i

n this

unit.

If M

ain

Fuse

(F60

1) is

blown

, che

ck to

see t

hat a

ll com

pone

nts in

the p

ower

supp

lyci

rcui

t are

not

def

ectiv

e be

fore

you

con

nect

the

AC p

lug

to th

e AC

pow

er s

uppl

y.O

ther

wise

it m

ay c

ause

som

e co

mpo

nent

s in

the

powe

r sup

ply

circu

it to

fail.

For c

ontin

ued

prot

ectio

n ag

ains

t risk

of f

ire,

repl

ace

only

with

sam

e ty

pe 4

A, 1

25V

fuse

.CA

UTIO

N ! :

ATT

ENTI

ON

: Utili

ser u

n fu

sible

de

rech

ange

de

mm

e ty

pe d

e 4

A, 1

25V.

4A/1

25V

NO

TE:

The

volta

ge fo

r par

ts in

hot

circ

uit i

s m

easu

red

usin

gho

t GND

as

a co

mm

on te

rmin

al.

10-7

DVD System Control / Servo Block Diagram

A94N1BLSD

IC30

1(S

ERVO

D

RIV

E)

CN30

1

M

SLED

M

OTO

R

M

SPIN

DLE

MO

TOR

IC10

1(M

ICRO

CO

NTRO

LLER

)

+ -+ -

+ -+ -

+ -+ - + -

SLED

MOT

OR

DR

IVE

FOCU

SAC

TUAT

OR

DR

IVE

SPIN

DLE

MOT

OR

DR

IVE

TRAC

KING

ACTU

ATO

RD

RIV

E12

6

LOAD

-DIS

C

SLD

67

SPDL

66

TRAC

KING

DR

IVE

127

FOCU

S DR

IVE

FS(+)

FS(-)

TS(+)

TS(-)

LOAD

-DIS

C

1SP

(+)2

SP(-)

6LO

AD-D

ISC

3G

ND4

SL(-)

5SL

(+)

VREF

RES

ET70

RES

ET

IC46

2

13

+3.

3V

IC20

2(O

P AM

P)

15 16 14 13 12 11 17 182364 531 225 2427 26

121

SP-R

OT

124

FD-O

FST

123

TD-O

FST

RES

ET

IC46

1

21

+3.

3V

TO DV

D D

IGIT

AL

SIG

NAL

PRO

CESS

BL

OCK

DIA

GRA

M

DR

IVE

CBA

DVD

MA

IN C

BA U

NIT

122

SL-A

DS

DIS

C-IN

12 6

753

3DV

D-DI

SC-IN

32

DVD-

DISC

-OUT

2CN8

01CN

5001

DIS

C-O

UT

SENS

OR

CBA

+3.

3V

1LE

D-P

OWER

1

Q804

63DV

D-D

ISC-

IN61

DVD

-DIS

C-O

UT

TO SYST

EM C

ONT

ROL

BLO

CK D

IAG

RAM

53DV

D-S

CLK

54DV

D-C

S

49DV

D-R

EMOT

E56

DVD

-SDA

TA

DVD

-SCL

KDV

D-C

SDV

D-S

DATA

DVD

-REM

OTE

LED

-CO

NTDV

D-D

ISC-

OUT

DVD

-DIS

C-IN

77DV

D-P

-ON

DVD

-P-O

N

65

1

NO

TE:

Ei

ther

IC46

1 or

IC46

2 is

used

for D

VD M

AIN

CBA

UNIT

.

10-8 A94N1BLDD

C16

D18

A17

B15

DVD

-LD

8CD

-LD

10

PD-M

ONI

7

FS(+)

2FS

(-)3

TS(+)

1TS

(-)4CN

201

CN20

1

CN20

1

IC20

1(S

W)

IC10

1(M

ICRO

CO

NTRO

LLER

)

FS

FS(+)

CD/D

VD

FS(-)

TS(+)

TS(-)

TSDETE

CTO

R

CD/D

VD19

Q251

,Q25

2

CDDV

D

AMP

Q253

,Q25

4AM

P

4

13

6

GND(C

D-PD)

5GN

D(LD

)9

RF SIG

NAL

PRO

CESS

CIRC

UIT

DVD

/CD

FORM

ATTE

R

AUD

IOI/F VI

DEO

I/FN

TSC/

PAL

ENCO

DER

DM

A

BCU

INST

.

ROM

32BI

TCP

UDA

TAR

AM

INTE

RRU

PTCO

NTRO

LLER

WAT

CH D

OG

TIM

ERCP

UI/F

TIM

ER

DEC

ODE

RI/F

CPU

I/FR

EAD

MEM

ORY

DATA

RAM

DSP

DEC

ODE

R

I/O PRO

CESS

OR

INST

.

ROM

DATA

RAM

INST

.

ROM

SERI

AL

D/A

GEN

ERAL

I/O INTE

RRU

PTCO

NTRO

LLER

TIM

ER

WAT

CH D

OG

TIM

ER

REM

OTE

CONT

ROL

32BI

T CP

U

STRE

AMI/F

EXTE

RN

AL

MEM

ORY

I/FSD

RAM

ECC

UMAC

100

115

116

113

114

106

104

105

103

62

DEB

UG

BCU

INST

CACH

EDA

TACA

CHE

D/A

131

130

Y Pb

DVD

-Y

DVD

-Pb

152

DVD

-SPD

IF

151

DVD-

AUDI

O-MU

TE

146

DVD-

AUDI

O(R)

144

DVD-

AUDI

O(L)

SDRA

M A

DDRE

SS(0-

10)

IC10

3(F

LASH

RO

M)

FLAS

HRO

M

29 36 38 45

~

~

FDQ

(0-15

)

~1 9 16 25 48

~

FAD

R (0

-19)

SDRA

M D

ATA(

0-15)

PICK

UP

TO DV

D S

YSTE

M

CONT

ROL

/ SER

VOBL

OCK

DIA

GRA

M

DVD

MA

IN C

BA U

NIT

TO VI

DEO

BLO

CK

DIA

GRA

M

TO AU

DIO

BLO

CK

DIA

GRA

M

IC50

3(SD

RAM)

SDRA

M D

ATA(

0-15)

SDRA

M A

DDRE

SS(0-

10)

194

209~

2 13 42 53

~

~

22 26 29 34

~ ~

159

178~

99 98 97

21~3

034

~42

212

1~4

7~14

17~1

821

5 2

16

AUD

IO D

/ACO

NVER

TER

D/A

129

PrDV

D-P

r

GND(D

VD-P

D)6

VID

EO S

IGNA

LA

UDIO

SIG

NAL

TO

SYST

EMCO

NTRO

LBL

OCK

DIA

GRA

M

DVD Digital Signal Process Block Diagram

11-1 FL9_3_SC

SCHEMATIC DIAGRAMS / CBA AND TEST POINTSStandard NotesWARNINGMany electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts that have these special safety characteristics are identified in this manual and its supplements; electrical components having such features are identified by the mark # in the schematic diagram and the parts list. Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement parts that do not have the same safety characteristics as specified in the parts list may create shock, fire, or other hazards.

Notes:1. Do not use t

emerson ld190, ld195, 19md359 tv-dvd_lcd

Documents