4700 Broadmoor SE, Suite 200 Kentwood, MI 49512 Telephone: 616-656-7401 Facsimile: 616-656-2022 www.intertek-etlsemko.com

Emeco Report No.:102021948GRR-001 Date: March 26, 2015 Page 1 of 26 _________________ ____________________ Jacob Wisniewski Anthony Serge Project Manager Reviewer This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program.

Test Report For:

Emeco

BS EN 16139:2013 BS EN 1728:2012

Navy Chair

Emeco Report No.:102021948GRR-001 Date: March 26, 2015 Page 2 of 26

Attention: Magnus Breitling Emeco 805 Elm Avenue Hanover, PA 17731 Phone: (717) 637-5951 ext. x4 Fax: (717) 633-6018 Email: magnus@emeco.net DATE RECEIVED: 2/11/15 DATES TESTED: 2/27/15 – 3/23/15 DESCRIPTION OF SAMPLES: Part Description: Navy Chair Condition of Test Sample: New WORK REQUESTED/APPLICABLE DOCUMENTS: To test the submitted sample per BS EN 16139:2013 Test Standard for the following test program:

Test No.

Reference Test Description

1 EN 1728:2012, 6.4 Seat and Back Static Load Test 2 EN 1728:2012, 6.5 Seat Front Edge Static Load Test 3 EN 1728:2012, 6.6 Vertical Static Load on Back 8 EN 1728:2012, 6.17 Seat and Back Durability Test 9 EN 1728:2012, 6.18 Seat Front Edge Durability Test

12 EN 1728:2012, 6.15 Leg Forward Static Load Test 13 EN 1728:2012, 6.16 Leg Sideways Static Load Test 14 EN 1728:2012, 6.24 Seat Impact Test 15 EN 1728:2012, 6.25 Back Impact Test 21 EN 1728:2012, 6.28 Backward Fall Test 22 EN 1728:2012, 6.27.3 Drop Test From the Height of a Table

Emeco Report No.:102021948GRR-001 Date: March 26, 2015 Page 3 of 26

CONCLUSION:

Test Results Notation EN 1728:2012, 6.4

Seat and Back Static Load Test Compliant No loss of serviceability.

EN 1728:2012, 6.5 Seat Front Edge Static Load Test Compliant No loss of serviceability.

EN 1728:2012, 6.6 Vertical Static Load on Back Compliant No loss of serviceability.

EN 1728:2012, 6.17 Seat and Back Durability Test Compliant No loss of serviceability.

EN 1728:2012, 6.18 Seat Front Edge Durability Test Compliant No loss of serviceability.

EN 1728:2012, 6.15 Leg Forward Static Load Test Compliant No loss of serviceability.

EN 1728:2012, 6.16 Leg Sideways Static Load Test Compliant No loss of serviceability.

EN 1728:2012, 6.24 Seat Impact Test Compliant No loss of serviceability.

EN 1728:2012, 6.25 Back Impact Test Compliant No loss of serviceability.

EN 1728:2012, 6.28 Backward Fall Test Compliant No loss of serviceability.

EN 1728:2012, 6.27.3 Drop Test From the Height of a Table Compliant No loss of serviceability.

TEST EQUIPMENT:

Asset Description Cal Date Cal Due 138379 Stopwatch 09/02/2014 09/02/2016 138012 SCALE / 0-1,000 # 11/24/2014 11/24/2015 138148 DIGITAL PROTRACTOR 09/11/2014 09/11/2015 138279 FORCE GAGE; DIGITAL 100LB 03/31/2014 03/31/2015 138112 GRADUATED RULE 36" 10/11/2013 10/11/2018 138211 BED EDGE TESTER VBU VBU 138205 IMPACT TESTER VBU VBU 138247 MULTI-LOAD TESTER VBU VBU 138213 IMPACT HAMMER VBU VBU

Emeco Report No.:102021948GRR-001 Date: March 26, 2015 Page 4 of 26

1. Seat and Back Static Load Test (Level 2): Date Tested: 2/27/15 Condition of Test Sample: New Number of Samples Tested: One (1) Test Procedure: Test Method: EN 1728:2012, 6.4 Seat Load: 2,000 N Back Load: 700 N

x Apply designated load to seat. x While maintaining seat load, apply the back load. x Repeat for 10 cycles.

Acceptance Criteria: There shall be no fractures of any member, joint, or component. No loosening of joints intended to be rigid. Seating shall remain functional, and fulfill stability requirements. Results:

Sample ID Cycles Description of Results 1 10 Pass

The submitted sample meets the acceptance criteria of the test described above. Refer to the following page for photograph.

Emeco Report No.:102021948GRR-001 Date: March 26, 2015 Page 5 of 26

Seat and Back Static Load

Emeco Report No.:102021948GRR-001 Date: March 26, 2015 Page 6 of 26

2. Seat Front Edge Static Load Test (Level 2): Date Tested: 3/2/15 Condition of Test Sample: New Number of Samples Tested: One (1) Test Procedure: Test Method: EN 1728:2012, 6.5 Seat Load: 1,600 N

x Apply the specified force using the seat loading pad at a point on the seat center line 100 mm inwards from the front edge.

x Repeat 10 times. Acceptance Criteria: There shall be no fractures of any member, joint, or component. No loosening of joints intended to be rigid. Seating shall remain functional, and fulfill stability requirements. Results:

Sample ID Cycles Description of Results 1 10 Pass

The submitted sample meets the acceptance criteria of the test described above. Refer to the following page for photograph.

Emeco Report No.:102021948GRR-001 Date: March 26, 2015 Page 7 of 26

Seat Front Edge Static Load

Emeco Report No.:102021948GRR-001 Date: March 26, 2015 Page 8 of 26

3. Vertical Static Load on Back (Level 2): Date Tested: 3/2/15 Condition of Test Sample: New Number of Samples Tested: One (1) Test Procedure: Test Method: EN 1728:2012, 6.6 Seat Load: 1,800 N

x Place designated load in seat. x Apply a vertical static force of 900 N to the top of the back rest. x Repeat for 10 cycles.

Acceptance Criteria: There shall be no fractures of any member, joint, or component. No loosening of joints intended to be rigid. Seating shall remain functional, and fulfill stability requirements. Results:

Sample ID Cycles Description of Results 1 10 Pass

The submitted sample meets the acceptance criteria of the test described above. Refer to the following page for photograph.

Emeco Report No.:102021948GRR-001 Date: March 26, 2015 Page 9 of 26

Vertical Static Load on Back

Emeco Report No.:102021948GRR-001 Date: March 26, 2015 Page 10 of 26

8. Seat and Back Durability Test (Level 2): Date Tested: 3/2/15 – 3/12/15 Condition of Test Sample: New Number of Samples Tested: One (1) Test Procedure: Test Method: EN 1728:2012, 6.17 Seat Load: 1,000 N Back Load: 300 N

x Apply designated loads to seat and back. x Repeat for 200,000 cycles.

Acceptance Criteria: There shall be no fractures of any member, joint, or component. No loosening of joints intended to be rigid. Seating shall remain functional, and fulfill stability requirements. Results:

Sample ID Cycles Description of Results 1 200,000 Pass

The submitted sample meets the acceptance criteria of the test described above. Refer to the following page for photograph.

Emeco Report No.:102021948GRR-001 Date: March 26, 2015 Page 11 of 26

Seat and Back Durability

Emeco Report No.:102021948GRR-001 Date: March 26, 2015 Page 12 of 26

9. Seat Front Edge Durability Test (Level 2): Date Tested: 3/13/15 – 3/17/15 Condition of Test Sample: New Number of Samples Tested: One (1) Test Procedure: Test Method: EN 1728:2012, 6.18 Force: 800 N

x Apply designated force alternatively on two points, each 100 mm from the front edge and 100 mm in from each side edge.

x Repeat for 100,000 cycles. Acceptance Criteria: There shall be no fractures of any member, joint, or component. No loosening of joints intended to be rigid. Seating shall remain functional, and fulfill stability requirements. Results:

Sample ID Cycles Description of Results 1 100,000 Pass

The submitted sample meets the acceptance criteria of the test described above. Refer to the following page for photograph.

Emeco Report No.:102021948GRR-001 Date: March 26, 2015 Page 13 of 26

Seat Front Edge Durability

Emeco Report No.:102021948GRR-001 Date: March 26, 2015 Page 14 of 26

12. Leg Forward Static Load Test (Level 2): Date Tested: 3/19/15 Condition of Test Sample: New Number of Samples Tested: One (1) Test Procedure: Test Method: EN 1728:2012, 6.15 Seat Load: 1,800 N Force: 620 N

x Place designated load in seat. x Apply a horizontal force centrally to the rear of the seat, at seat level, in a

forward direction. x Repeat for 10 cycles.

Acceptance Criteria: There shall be no fractures of any member, joint, or component. No loosening of joints intended to be rigid. Seating shall remain functional, and fulfill stability requirements. Results:

Sample ID Cycles Description of Results 1 10 Pass

The submitted sample meets the acceptance criteria of the test described above. Refer to the following page for photograph.

Emeco Report No.:102021948GRR-001 Date: March 26, 2015 Page 15 of 26

Leg Forward Static Load

Emeco Report No.:102021948GRR-001 Date: March 26, 2015 Page 16 of 26

13. Leg Sideways Static Load Test (Level 2): Date Tested: 3/19/15 Condition of Test Sample: New Number of Samples Tested: One (1) Test Procedure: Test Method: EN 1728:2012, 6.16 Seat Load: 1,800 N Force: 760 N

x Place designated load in seat. x Apply a horizontal force centrally to the side of the seat, at seat level, in the

direction towards the restrained feet. x Repeat for 10 cycles.

Acceptance Criteria: There shall be no fractures of any member, joint, or component. No loosening of joints intended to be rigid. Seating shall remain functional, and fulfill stability requirements. Results:

Sample ID Cycles Description of Results 1 10 Pass

The submitted sample meets the acceptance criteria of the test described above. Refer to the following page for photograph.

Emeco Report No.:102021948GRR-001 Date: March 26, 2015 Page 17 of 26

Leg Sideways Static Load

Emeco Report No.:102021948GRR-001 Date: March 26, 2015 Page 18 of 26

14. Seat Impact Test (Level 2): Date Tested: 3/23/15 Condition of Test Sample: New Number of Samples Tested: One (1) Test Procedure: Test Method: EN 1728:2012, 6.24 Weight of Impactor: 25 kg

x Place one layer of 25 mm thick foam on the seat. Determine the height of the fall from the position of the impactor when it is resting on the surface of the foam.

x Place a second layer of 25 mm foam on the seat. x Allow the seat impactor to fall freely from 300 mm onto the seat loading position. x Repeat for 10 cycles.

Acceptance Criteria: There shall be no fractures of any member, joint, or component. No loosening of joints intended to be rigid. Seating shall remain functional, and fulfill stability requirements. Results:

Sample ID Cycles Description of Results 1 10 Pass

The submitted sample meets the acceptance criteria of the test described above. Refer to the following page for photograph.

Emeco Report No.:102021948GRR-001 Date: March 26, 2015 Page 19 of 26

Seat Impact Test

Emeco Report No.:102021948GRR-001 Date: March 26, 2015 Page 20 of 26

15. Back Impact Test (Level 2): Date Tested: 3/23/15 Condition of Test Sample: New Number of Samples Tested: One (1) Test Procedure: Test Method: EN 1728:2012, 6.25 Height of Fall, mm/°: 330/48

x Strike the center of the top outside of the back with the impact hammer. Drop the hammer through the height, or angle, specified.

x Repeat for 10 cycles. Acceptance Criteria: There shall be no fractures of any member, joint, or component. No loosening of joints intended to be rigid. Seating shall remain functional, and fulfill stability requirements. Results:

Sample ID Cycles Description of Results 1 10 Pass

The submitted sample meets the acceptance criteria of the test described above. Refer to the following page for photograph.

Emeco Report No.:102021948GRR-001 Date: March 26, 2015 Page 21 of 26

Back Impact Test

Emeco Report No.:102021948GRR-001 Date: March 26, 2015 Page 22 of 26

21. Backward Fall Test (Level 2): Date Tested: 3/23/15 Condition of Test Sample: New Number of Samples Tested: One (1) Test Procedure: Test Method: EN 1728:2012, 6.28

x Place the unloaded unit on the rubber padded drop test floor. x Apply a rearward horizontal load to a point 50 mm below the top of the back rest

at the center. Measure the force required to lift the front legs off the floor. x If the measured force is less than 30N, push the back rest until it reaches

equilibrium, and then allow it to fall freely on its back. x Repeat for 5 cycles.

Acceptance Criteria: There shall be no fractures of any member, joint, or component. No loosening of joints intended to be rigid. Seating shall remain functional, and fulfill stability requirements. Results:

Sample ID Cycles Description of Results 1 5 Pass

The submitted sample meets the acceptance criteria of the test described above. Refer to the following page for photograph.

Emeco Report No.:102021948GRR-001 Date: March 26, 2015 Page 23 of 26

Backward Fall Test

Emeco Report No.:102021948GRR-001 Date: March 26, 2015 Page 24 of 26

22. Drop Test From the Height of a Table (Level 2): Date Tested: 3/23/15 Condition of Test Sample: New Number of Samples Tested: One (1) Test Procedure: Test Method: EN 1728:2012, 6.27.3 Drop Height: 600 mm

x Support the seating so that one leg is lifted to the specified drop height, and the line joining that leg to the leg diagonally opposite is incline 10° to the horizontal.

x The two remaining legs shall be maintained at the same level. x Drop it on to the rubber faced test floor. x Perform 5 cycles on a front leg, and 5 cycles on a rear leg.

Acceptance Criteria: There shall be no fractures of any member, joint, or component. No loosening of joints intended to be rigid. Seating shall remain functional, and fulfill stability requirements. Results: Sample

ID Leg Cycles Description of Results

1 Front 5 Pass Rear 5 Pass

The submitted sample meets the acceptance criteria of the test described above. Refer to the following page for photograph.

Emeco Report No.:102021948GRR-001 Date: March 26, 2015 Page 25 of 26

Drop Test From the Height of a Table

Emeco Report No.:102021948GRR-001 Date: March 26, 2015 Page 26 of 26

SD 3.1.2 (10/19/07) Mandatory

Revisions Made To Test Report

Index Date Revision Description Revised by Revised by

001 26-March-2015 Initial release.

Jacob Wisniewski